Camp Chef Smoke Pro PG24SE-5 Warning & Instruction Booklet

Marque: Camp Chef

Modèle: Smoke Pro PG24SE-5

Catégorie: Barbecues

Taper: Warning & Instruction Booklet

PELLET GRILL AND SMOKER

WARNING & INSTRUCTION BOOKLET

MODEL PG24SE-5

www.CampChef.com | 1.800.650.2433 • Camp Chef is a registered trademark of Logan Outdoor Products

5003132

Conforms to UL SUBJECT 2728

Certiﬁed to CSA STD C22.2 #3

WARNING

FOR OUTDOOR USE ONLY

WARNING

If the information in this manual is not

followed exactly, a ﬁre or explosion may

result causing property damage, personal

injury or loss of life.

WARNING

• To installer or person assembling this appliance:

Leave this manual with this appliance for future

reference.

• To consumer: Keep this manual with this

appliance for future reference.

This instruction manual contains important

information necessary for the proper assembly

and safe use of this product. Read and follow

all warnings and instructions before assembling

and using this appliance. Do not discard this

instruction manual.

CAUTION

Use Only Wood Pellet Fuel Speciﬁed By The

Manufacturer. Do Not Use Pellet Fuel Labeled As

Having Additives. Only use Camp Chef Premium

Pellets with the following speciﬁcations. 8,000-

8,300 BTU/LB 0.75-0.85% Ash content

CAUTION

Contact local building or ﬁre ofﬁcials about

restrictions and installation inspection

requirements in your area.

A MAJOR CAUSE OF FIRES IS FAILURE TO

MAINTAIN REQUIRED CLEARANCES (AIR SPACES)

TO COMBUSTIBLE MATERIALS. IT IS OF UTMOST

IMPORTANCE THAT THIS PRODUCT BE INSTALLED

ONLY IN ACCORDANCE WITH THESE INSTRUCTIONS.

DANGER

1. Never operate this appliance unattended.

2. Never operate this appliance within 10 ft (3 m)

of a stored LP cylinder.

3. Never operate this appliance within 25 ft (7.5

m) of any ﬂammable liquid.

4. If a ﬁre should occur, keep away from

appliance and immediately call your ﬁre

department. Do not attempt to extinguish an oil

or grease ﬁre with water.

Failure to follow these instructions could result in

fire, explosion or burn hazard, which could cause

property damage, personal injury or death.

CAUTION

Always store wood pellets away from heat

producing appliances and other food containers.

Pellets should be stored in a dry environment.

WARNING

Normal use will create a buildup of ash, grease,

and creosote inside the grill. The grill must be

thoroughly cleaned after every 50 hours of use or

if a buildup of grease or creosote is noticed inside

the grill. Clean the grill by removing all internal

parts and thoroughly scrape away all grease and

creosote from all internal surfaces including the

grease drain and remove debris from the grill. The

drip tray must always be cleaned prior to turning

the grill to high. Excessive buildup of grease and

creosote may result in a grease ﬁre. If a grease

ﬁre does occur, turn off the grill using the main

power switch and close the lid. Leave the lid closed

until the ﬁre extinguishes itself. If an uncontrolled

ﬁre does occur, immediately call the local ﬁre

department. Never put water on a grease ﬁre.

PG24SE-5 PARTS

OPTIONAL

(NOT INCLUDED)

0217-PG24SE-5-PARTS

PG24SE-9 (1)

CHIMNEY

PG24SE-10 (1)

CHIMNEY CAP ASM

PG24-70 (2)

COOKING GRATE

PG24-3 (1)

DRIP TRAY

PG24-4 (1)

HEAT DEFLECTOR

PG24-11 (1)

GREASE BUCKET

M6 X 45 BOLT (14)

M6 NUT (8)

M6 LOCK WASHER (14)

M6 FLAT WASHER (8)

PG24-44 (1)

THERMOMETER

PG24-34 (1)

FEED GASKET

M6 FLAT WASHER (2)

M6 NUT (2)

M6 LOCK WASHER (2)

M6 X15 MACHINE SCREW (12)

PG24LS-9 (2)

HINGE BOLT WITH NUT

PG24LS-8 (2)

HINGE ASM

PG24LS-9 (2)

HINGE BOLT WITH NUT

PG24LS-1 (2)

WHEEL

PG24SE-1 (2)

WHEEL AXLE

M8 FLAT WASHER (2)

M8 NYLOC NUT (2)

PG24SE-13 (1)

HOPPER ASM

097110 (2)

1.25" LEG PLUG

PG24SE-4 (1)

FRONT LEG

PG24SE-5 (1)

REAR LEG

PG24SE-6 (2)

LEG BRACKET

PG24SE-7 (1)

WIRE SHELF

PG24LS-7 (1)

GRILL LID

PZ90-2 (1)

3" DELUXE THERMOMETER

PG24-54 (1)

PROBE COVER

M6 FLAT WASHER (2)

M6 NUT (2)

M6 LOCK WASHER (2)

PG24-7 (1)

CHIMNEY GASKET

1/4-20 X 3 BOLT (1)

1/4-20 NUT (2)

PG24LS-6 (1)

HANDLE

PG24-41 (1)

BURNER PULLOUT

PG24-42 (1)

PULLOUT LOCK

PG24-9 (1)

BURNER PULLOUT KNOB

PG24-17 (1)

ASH CUP

PG24-1 (1)

WARMING RACK

HARDWARE KIT - PG24SE-12

CHIMNEY HARDWARE KIT - PG24-73

CARBON MONOXIDE WARNING

Follow these guidelines to prevent this colorless, odorless gas from poisoning you, your family or others. Know the

symptoms of carbon monoxide poisoning: headache, dizziness, weakness, nausea, vomiting, sleepiness, and confusion.

Carbon monoxide reduces the blood’s ability to carry oxygen. Low blood oxygen levels can result in loss of consciousness

and death. See a doctor if you or others develop cold or ﬂu-like symptoms while cooking or in the vicinity of this

appliance. Carbon monoxide poisoning, which can easily be mistaken for a cold or ﬂu, is often detected too late. Alcohol

consumption and drug use increase the effects of carbon monoxide poisoning. Carbon monoxide is especially toxic to

mother and child during pregnancy, infants, the elderly, smokers and people with blood or circulatory system problems,

such as anemia, or heart disease.

0218-PG24SE-13-PARTS

PG24-21 (1)

HEATING ROD

PG24-22 (1)

AUGER

PG24-23 (1)

AUGER BUSHING

PG24-24 (1)

AUGER MOTOR

PG24-25 (1)

AUGER PIN W/NUT

PG24-26 (1)

BLOWER MOTOR

PG24-27 (1)

BLOWER IMPELLER

M4.2 X 10 SCREW (4)

PG24-45 (1)

CONTROLLER GASKET

PG24-51 (1)

GUARD PLATE

PG24-20 (1)

BURNER

PG24SE-3 (1)

CONTROLLER

PG24-30 (1)

CONTROLLER KNOB

M4.2 X 10 SCREW (2)

PG24LS-11 (1)

HOPPER LID

M6 X 15 SCREW (2)

M6 NUT (2)

M6 LOCK WASHER (2)

M6 FLAT WASHER (2)

PG24-49 (1)

AUGER IMPELLER

PG24SE-8 (1)

HOPPER COVER

PG24-48 (1)

POWER CORD

M4.2 X 10 SCREW (2)

PG24-53 (1)

AUGER GUARD

PGC24-12 (1)

HOPPER HANDLE

1. Do NOT leave this appliance unattended while in use.

The user must remain in the immediate area of the

product and have a clear view of the product at all times

during operation.

2. Keep children and pets away from burner at all times.

3. The use of alcohol, prescription or non-prescription drugs

may impair your ability to properly assemble or safely

operate

this appliance.

4. For OUTDOOR use only. Do NOT use in a building,

garage or any other enclosed area. Do NOT use in or on

recreational vehicles or boats. NEVER use this appliance

as a heater.

5. Do not operate appliance under ANY overhead

construction. Keep a minimum clearance of 36 inches

(0.9 m) from the sides, front and back of appliance to

ANY construction. Keep the area clear of all combustible

material and flammable liquids, including wood, dry

plants and grass, brush, paper, and canvas.

6. This product is not intended for commercial use.

7. Always allow the appliance to cool before covering with

the patio cover.

8. Always cover the appliance, with patio cover (if

supplied), when not in use.

9. Always unplug grill before installing patio cover.

10. Use only on a level, stable non-combustible surface like

bricks, concrete or dirt. Do not use this appliance on

any surface that will burn or melt like wood, asphalt,

vinyl or plastic.

11. Make sure the grease bucket is in place before starting

the grill.

12. In the event of a fire the dial should be turned to

shutdown, close the lid, and leave it closed until the

fire goes out. After allowing the grill to cool, follow the

cleaning instructions before the next use.

13. Use only food grade hardwood pellets manufactured for

use in pellet grills. Using softwood or heating pellets

will void your warranty.

14. Do not allow the hopper to run out of pellets. Pellets

can be added at any time. The hopper will hold

approximately 18 pounds of pellets. The pellet usage

will vary greatly depending on the ambient temperature

as well as

cooking temperature.

15. It is recommended that you not store pellets in the

hopper for extended periods as they may absorb

moisture from the air and clog the auger.

16. Keep the lid closed during cooking. The grill is designed

to cook with the lid closed.

17. Do not use accessories not specified for use with

appliance.

18. Never use gasoline, gasoline-type lantern fuel,

kerosene, charcoal lighter fluid, or similar liquids to

start or freshen up a fire in this appliance. Keep all

such liquids well away from the appliance when in use.

19. Ashes should be placed in a metal container with a

tight fitting lid. The closed container of ashes should

be placed on a non combustible floor or on the ground,

well away from all combustible materials, pending final

disposal. When the ashes are disposed by burial in soil

or otherwise locally dispersed they should be retained

in the closed container until all cinders have thoroughly

cooled.

20. Creosote – Formation and need for removal. When wood

pellets are burned slowly, they produce tar and other

organic vapors that combine with expelled moisture

to form creosote. The creosote vapors condense in a

relatively cool oven flue and exhaust hood of a slow

burning fire. As a result, creosote residue accumulates

on the flue lining and exhaust hood. When ignited,

this creosote makes an extremely hot fire. The grease

duct should be inspected every 50 hours to determine

when grease and/or creosote build-up has occurred.

When grease or creosote has accumulated, it should be

removed to reduce risk of fire.

DANGER

Do not work on this grill if it is plugged in. Electric shock

may occur resulting in death or serious injury.

Assembly Instructions

Remove all loose parts from the inside of the grill and

hopper. Lay a blanket or piece of cardboard down to protect

the grill.

Attach the Legs

With the help of another person flip the grill upside down

on the blanket or cardboard. The grill lid and hopper lid will

swing open when doing this so be careful not to damage

the lids. The grill may also want to roll on its lid so one

person should hold the grill steady while the other person

assembles the bottom legs and wheels.

1. Assemble the legs as shown in Fig. 1 using Qty (6)

M6 x 45 Bolts and Qty (6) Lock washers. Note that the

longer leg must go closest to the hopper. Finger tighten

hardware.

M6 LOCK WASHER

M6 X 45 BOLT

Fig. 1

2. Assemble Qty (2) leg brackets onto the legs as shown

in Fig 2 using Qty (4) M6 x 45 Bolts, Qty (4) M6 Flat

Washers, Qty (4) M6 Lock Washers, and Qty (4) M6 Nuts.

Finger tighten hardware.

3. Assemble the wire shelf to the legs as shown in Fig 2

using Qty (4) M6 x 45 Bolts, Qty (4) M6 Flat Washers, Qty

(4) M6 Lock Washers, and Qty (4) M6 Nuts. Finger tighten

hardware.

M6 FLAT WASHER

M6 X 45 BOLT

M6 LOCK WASHER

M6 NUT

M6 FLAT WASHER

M6 LOCK WASHER

M6 NUT

Fig. 2

4. Assemble Qty (2) Wheels to the legs as shown in Fig 3

using Qty (2) Wheel Axles, Qty (2) M8 Flat Washers, and

Qty (2) M8 Nyloc Nuts. Tighten axle hardware with a

wrench.

M8 FLAT WASHER

M8 NYLOC NUT

WHEEL AXLE

Fig. 3

5. With the help of another person, stand the grill upright.

Be careful as the lid on the hopper and grill will close as

the grill is stood upright.

6. Tighten all hardware assembled in the previous steps. Do

not crush the tubes by over tightening the hardware.

Attach Chimney and Chimney Cap

1. Install chimney to grill as shown in Fig 4. Make sure to

install the gasket between the grill and the chimney.

2. Tighten all hardware.

3. Install 1/4-20 x 3 Bolt through chimney cap and secure

using Qty (1) 1/4-20 nut. Thread second nut onto bolt

leaving approximately 1.5 in to the top of the cap. Thread

cap assembly down into the chimney bracket until the

lower nut hits the bracket. See Fig 4.

4. The height of the chimney cap can be adjusted for

summer and winter. In the summer the gap should be

approximately 1-1/2 in. In the winter the gap should be

approximately ½ in.

5. Tighten all hardware.

M6 X 15 SCREW

M6 NUT

M6 FLAT WASHER

M6 LOCK WASHER

CHIMNEY GASKET

1/4-20 X 3 BOLT (1)

1/4-20 NUT (2)

Fig. 4

Install Handle

1. Install the handle as shown in Fig 5.

2. Tighten all hardware.

M6 FLAT WASHER (2)

M6 NUT (2)

M6 LOCK WASHER (2)

PG24LS-6 (1)

HANDLE

Fig. 5

Install Hopper Handle

1. Install hopper handle as shown in Fig. 6.

HOPPER HANDLE (1)

PGC24-12

M6 RUBBER WASHER (2)

M6 FENDER WASHER (2)

M6 LOCK WASHER (2)

M6 X 15 BOLT (2)

Fig. 6

Grease Bucket

1. Hang grease bucket from tube as shown in Fig 7.

GREASE BUCKE

ASH CUP

Fig. 7

Ash Cup

1. Install Ash Cup as shown in Fig 8. Never use grill without

Ash Cup in place.

Install Deﬂector and Drip Tray

1. Install the Heat Deﬂector and Drip Tray as shown in Fig 8

and Fig 9.

HEAT DEFLECTOR

DRIP TRAY

Fig. 8

HEAT DEFLECTOR

DRIP TRAY

Fig. 9

Warming Rack and Cooking Grate (Optional Rack Model

PG24-1 Not Included)

1. Install the Warming Rack and Cooking Grate as shown in

Fig 10.

PG24-70 (2)

COOKING GRATE

PG24-1 (OPTIONAL)

WARMING RACK

(NOT INCLUDED)

Fig. 10

Clean-out Knob Assembly Installation

Hand tighten the burner clean-out knob as shown in Fig 11.

PG24-9 (1)

BURNER PULLOUT KNOB

Fig. 11

Clean-out Port Knob

1. Clean-out Port knob must be pushed in when grill is on.

Make sure pullout lock is pushed down and locks the

knob to prevent inadvertent opening of the clean-out port.

See Fig 12.

CLEANOUT PORT CLOSED

CLEANOUT PORT OPEN

Fig. 12

2. Lift pullout lock and pull clean-out port knob to empty

ash into ash cup. See Fig 13.

CLEANOUT PORT CLOSED

CLEANOUT PORT OPEN

Fig. 13

3. See instructions for burner clean-out.

Burner Clean-out

Before each use the burner should be cleaned out by lifting

the pullout lock and pulling the clean-out port knob on the

right side of the grill to open the burner clean-out. This will

allow the ash from previous use to fall into the cup under

the grill. The cup should be removed and emptied and then

reinstalled before each use.

After cleaning out the burner make sure to close the burner

clean-out by pushing the clean-out port knob in on the right

side of the grill. Make sure to lift the pullout lock and push

the clean-out port knob all the way in and lock in place

with the pullout lock. Every 50 hours of use, remove the grill

grates, grease tray, and heat deﬂector and clean the inside

of the grill. If you notice a lot of ash blowing around in the

grill it is time to vacuum it out.

DANGER

Never Operate the Pellet grill without the ash cup in place.

Make sure the burner clean-out port is closed and locked

before starting the grill.

WARMING RACK

COOKING GRATE

CLEANOUT PORT KNOB

Never open the burner clean-out port when the grill is hot.

Filling the Auger Tube

Caution: Only use the feed setting when the hopper has

ran out of pellets. Feed setting is not for normal use.

The ﬁrst time you use your grill or any time the hopper has

ran out of pellets you will need to ﬁll the auger tube. This

simply means you must ﬁll the auger tube with pellets until

pellets reach the burner. This is done by turning the dial

to the FEED position. The auger will remain on for no more

than 7 minutes. This is ample time for the pellets to reach

the burner. It is easiest to open the burner clean-out by

pulling the knob on the right side of the grill. Once you hear

pellets dropping into the cup you can close the clean-out

port by pushing the knob on the right side of the grill and

then select your cooking temperature. (Never operate grill

without the ash cup in place). Always make sure the burner

clean-out port is closed by pushing in the knob on the right

side of the grill before selecting any of the cook settings.

Never open the burner clean-out port when the grill is hot.

Controller Explanation

Power Switch

Used to turn the main power onto the pellet grill. The fan

will be on whenever the power switch is on. The dial must

be rotated to any of the other positions before the grill will

start. If the power is turned on with the dial in any other

position than Shutdown the grill will immediately start that

function. “O” is Off. “-“ is On. See Fig 14

Fig. 14

Dial Positions

Shutdown -This setting must be used after each use. Turn

the dial to this setting and the fan will remain on. Wait for

10 minutes to allow the grill to ﬁnish burning any pellets in

the burner before turning the main power switch off. This

setting will burn up any extra pellets in the burner and cool

down the grill. Do not turn the main power switch off when

the grill is hot.

Low Smoke - This setting is used for smoking foods at an

average temperature of 160F. This setting will produce large

amounts of smoke.

High Smoke - This setting is used for smoking foods at an

average temperature of 220F. This setting will produce large

amounts of smoke.

175F to 400F - There are 25F increment settings from 175F

to 400F. You can simply select any temperature you want

and the grill will control the temperature within 15F of the

selected temperature.

High - This setting can be used to achieve temperatures up

to 500F depending on ambient temperatures.

Feed - This setting is used to feed pellets to the hopper. It

will be used the ﬁrst time you use the grill to ﬁll the auger

tube and any time you may inadvertently run the hopper out

of pellets. See instructions on ﬁlling the auger tube.

Display

LED Flashing Green – The LED will ﬂash green each time

the dial is changed from the OFF, SHUTDOWN, or FEED

settings, to any of the cook settings indicating that the grill

is in the startup cycle.

LED Green – A green LED light indicates that the grill in

functioning normally in any of the cook settings.

RED LED – The LED will be red when the dial is turned to the

shutdown mode or the ﬂame is extinguished in any of the

cook settings.

LED Flashing Red – The LED will ﬂash Red if there is an

error with the temperature sensor inside of the grill.

Breaking In the Grill

We suggest turning the grill to 350F for ½ hour before

cooking on the grill for the ﬁrst time. This will burn off any

manufacturing oils and cure the paint. Make sure to follow

the instructions for ﬁlling the auger tube before breaking in

the grill.

DANGER

Always start the grill with the lid open. The lid must be

closed after the start cycle.

Cooking

Once the auger tube has been properly ﬁlled you can begin

cooking by selecting any of the cooking temperatures. The

grill has 13 cook settings. Low Smoke, High Smoke, 175,

200, 225, 250, 275, 300, 325, 350, 375, 400, and High. By

selecting any of these the grill will go into the Startup mode.

The LED will ﬂash green for 8 minutes during the startup

cycle. After the 8 minutes the LED be green. The dial can be

changed at any time during the startup cycle or the cook

cycle between any of the 13 cook settings.

DANGER

Do not over-ﬁre the grill by over feeding pellets into the

burner prior to startup. If ﬂame is inadvertently extinguished

never restart the grill without ﬁrst cleaning out the burner.

Improper use can cause an uncontrolled ﬁre.

Shutdown

When you are done cooking the dial must be turned to the

Shutdown setting. The LED will be red. In this setting the

fan will remain on to ﬁnish burning any pellets in the burner

and cool the grill down. After 10 minutes, if the grill has

cooled the main power switch should be switched to off.

DANGER

Do not turn the main power switch off while the grill is hot.

Cleaning

Clean grates using a wire grill brush. This should be

done with each use. DO NOT use oven cleaner or abrasive

cleaners on the painted grill surfaces. Use warm soapy

water on all painted surfaces. Clean grease pan, grease

trough, and grease drain tube occasionally. A spatula can

be used to scrape excess grease and a grill brush to brush

clean. Do not allow grease to build up on the grease tray

or in the grease trough as this can cause ﬂare-ups inside

the grill. The grease tray can also be lined with aluminum

foil for easier cleanup. Make sure not to obstruct the ﬂow of

grease off of the tray and into the grease trough. Make sure

not to block the airﬂow to the temperature sensor on the left

side of the grill.

WARNING

Normal use will create a buildup of ash, grease, and creosote

inside the grill. The grill must be thoroughly cleaned after

every 50 hours of use or if a buildup of grease or creosote

is noticed inside the grill. Clean the grill by removing all

internal parts and thoroughly scrape away all grease and

creosote from all internal surfaces including the grease

drain and remove debris from the grill. The drip tray must

always be cleaned prior to turning the grill to high. Excessive

buildup of grease and creosote may result in a grease ﬁre.

If a grease ﬁre does occur, turn off the grill using the main

power switch and close the lid. Leave the lid closed until the

ﬁre extinguishes itself. If an uncontrolled ﬁre does occur,

immediately call the local ﬁre department. Never put water

on a grease ﬁre.

CHIMNEY CLEANING

When wood pellets are burned slowly, they produce tar and

other organic vapors that combine with expelled moisture to

form creosote. The creosote vapors condense in a relatively

cook oven chimney of a slow burning ﬁre. As a result,

creosote residue accumulates on the chimney. When ignited,

this creosote makes an extremely hot ﬁre. The chimney

should be inspected every 50 hours of use, to determine

when grease and or creosote buildup has occurred. When

grease or creosote has accumulated, it should be removed

to reduce risk of ﬁre. Use a wire brush to clean the screen

area of the chimney outlet on the inside of the grill with

every 50 hours of use. The chimney must be removed and

thoroughly cleaned to remove creosote and grease buildup

every 200 hours of use.

Troubleshooting

Grill does not turn on.

Grill fails to turn on after switching the power button to the

on position.

1. Make sure the grill is plugged into a powered outlet.

Check the circuit breaker and/or GFCI switch. Test the

outlet using another appliance.

2. Unplug the grill and remove the control panel on the

controller. Check the fuse located on the back of the

controller. If the fuse is blown replace only with 4.0 Amp

125V 5x20mm Fast Blow Fuse. Typical fuse marking will

be 4A125V, F4A125, 4A250V or F4A250V. Make sure to

conﬁrm they are a fast blow fuse. Actual fuse dimensions

are 5.2x20mm. If problem cannot be resolved please call

customer service.

Grill does not heat up or LED is red

1. Turn Power Off

2. Check hopper for pellets

3. Check ﬁrebox to see if there are pellets in the ﬁrebox by

removing the rack and heat deﬂectors. Use a vacuum to

clean-out any pellets that may be in the bottom of the

grill.

A. Try restarting the grill. If restarting the grill does not work

and pellets are getting to the burner cup the heating rod

may need to be replaced.

B. If there are few or no pellets in the burner then turn the

dial to the feed position and see if pellets fall into the

burner. If there are no pellets check to see if the auger

is turning. If the auger motor is turning but the auger is

not there may be a sheared auger pin. You can determine

if the auger motor is turning by watching the small white

fan at the end of the auger motor under the hopper. If the

white fan is turning the auger motor is on. If the white fan

is turning and the auger is not you will need to replace

the auger pin. If problem cannot be resolved please call

customer service.

LED ﬂashes red

1. Turn the power off and unplug the grill.

2. Check to make sure the sensor inside of the grill is

connected properly to the electronic board under the

hopper.

3. Call customer service for a replacement sensor.

LIMITED WARRANTY

Camp Chef No-Hassle Warranty

Here at Camp Chef we stand by our products and take pride in our

customer service. Because of this, your new Camp Chef product comes

with a No-Hassle Warranty. What does that mean? It means that if we

did something wrong, we will make it right. We guarantee our products

to be free from defect in all materials and workmanship (excluding

paint and ﬁnish). We will replace defective parts so you can get back to

enjoying your product as soon as possible.

Required Maintenance:

Clean your product after each use to maintain its ﬁnish and prolong

its lifespan. Wipe away all grease and ashes. Keep metal products

free of moisture, salts, acids and harsh ﬂuctuations in temperature.

Unfortunately, product paint and other ﬁnishes are not covered by this

warranty. The exterior ﬁnish of the product will wear down over time.

Coverage Details:

Warranty does not cover normal wear of parts or damage caused

by misuse, abuse, overheating and alteration. No alterations are

covered in this warranty. Camp Chef is not responsible for any loss

due to neglectful operation. Furthermore, this warranty does not cover

items purchased from a 3rd party company, unauthorized dealers, or

damages caused by natural disasters such as earthquakes, hurricanes,

tornadoes, ﬂoods, lightning, ﬁres, etc.

Upon the expiration of this warranty, all such liability will terminate. No

other warranties are expressed or implied.

Please keep all original sales receipts from the authorized dealer.

Proof of purchase is required to obtain warranty services. Any parts

or products returned without written authorization will be discarded

without notice.

To obtain warranty services submit a warranty request at

http://www.campchef.com/warranty-information, email warranty@

campchef.com, or call 1.800.650.2433. Mon-Fri 7 AM-5 PM MST

Our English speaking Product Specialists are happy to help.

Warranty applies to the contiguous U.S. states only.

WARRANTY COVERAGE PERIODS

Pellet Grills 3 year from purchase date

Stoves 1 year from purchase date

Fire Pits 1 year from purchase date

Water Heaters 1 year from purchase date

Movie Screens 1 year from purchase date

All other items & accessories 90 days from purchase date

White

Black

Auger Motor Blower Fan

Burner

Controller

RTD Sensor

Power Cord

White

Red

White

Orange

White

Purple

Hot Rod

MOLEX Connector

4A 125V

4 amp 125V

5 x 20 MM

Fast Blow Fuse

CAUTION

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1 this device may

not cause harmful interference, and 2 this device must accept any interference received, including interference that may

cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

www.CampChef.com • 1.800.650.2433 • Camp Chef is a registered trademark of Logan Outdoor Products

5003132

Conforms to UL SUBJECT 2728

Certiﬁed to CSA STD C22.2 #3

BARBECUE À GRANULES

AVERTISSEMENT & INSTRUCTION BROCHURE

MODÈLE: PG24SE-5

www.CampChef.com | 1.800.650.2433 • Camp Chef is a registered trademark of Logan Outdoor Products

AVERTISSEMENT

DESTINÉ À UN USAGE EN PLEIN

AIR UNIQUEMENT

AVERTISSEMENT

• À l’attention de l’installateur ou de la personne

chargée d’assembler cet appareil : conserver

la présente notice d’utilisation avec l’appareil

pour un usage ultérieur.

• À l’attention du consommateur : conserver la

présente notice pour un usage ultérieur.

La présente notice d’utilisation contient des

informations importantes nécessaires au

montage correct et à l’utilisation sécuritaire de

ce produit.

NE PAS JETER LA PRÉSENTE NOTICE D’UTILISATION.

AVERTISSEMENT

1. Ne jamais faire fonctionner cet appareil sans

surveillance.

2. N’utilisez jamais cet appareil à moins de 10 pi

(3 m) d’une bouteille de GPL conservée.

3. Ne jamais utiliser le présent appareil à moins

de 7,5 m (25 pi) de tout liquide inflammable.

4. En cas d’incendie, rester à bonne distance de

l’appareil et appeler immédiatement le service

des incendies. Ne pas essayer d’éteindre un

feu d’huile ou de friture avec de l’eau.

Le non-respect de ces consignes peut

entraîner des dommages matériels, des

blessures corporelles ou la mort pouvant

résulter d’un incendie, d’une explosion ou

d’un danger de brûlure.

AVERTISSEMENT

Entreposer en permanence les granules de bois

à l’abri des appareils produisant de la chaleur

et d’autres récipients alimentaires. Les granules

doivent être entreposés dans un endroit sec.

CAUTION

Contacter les autorités locales du bâtiment

ou de la protection incendie pour connaître les

restrictions et les exigences d’inspection en

vigueur dans votre région.

LE NON-RESPECT DES DÉGAGEMENTS (ESPACES

VIDES) REQUIS POUR LES MATÉRIAUX

COMBUSTIBLES CONSTITUE UNE DES PRINCIPALES

CAUSES D’INCENDIES. IL EST DONC PRIMORDIAL

D’INSTALLER CE PRODUIT CONFORMÉMENT À LA

PRÉSENTE NOTICE.

CAUTION

Utiliser uniquement les granules de bois indiqués

par le fabricant. Ne pas utiliser de granules de

bois dont les spéciﬁcations indiquent la présence

d’additifs. Utiliser uniquement des granules de

bois Camp Chef de première qualité répondant aux

spéciﬁcations suivantes : 8 000 à 8 300 BTU/LB

Taux de cendre de 0,75 à 0,85 %

AVERTISSEMENT

Une utilisation normale créera une accumulation

de cendres, de graisse et de créosote dans le

gril. Le gril doit être nettoyé à fond toutes les 50

heures d’utilisation ou si une accumulation de

graisse ou de créosote est observée à l’intérieur

du gril. Nettoyez le gril en enlevant toutes les

pièces internes et enlevez soigneusement toutes

les graisses et créosotes de toutes les surfaces

internes, y compris le drain de graisse et enlevez

les débris du gril. Le bac d’égouttement doit

toujours être nettoyé avant de mettre le gril en

position haute ou de cuire en mode ﬂamme directe.

Une accumulation excessive de graisse et de

créosote peut provoquer un incendie de graisse.

Si un feu de graisse se produit, éteignez le gril

à l’aide de l’interrupteur principal et fermez le

couvercle. Laissez le couvercle fermé jusqu’à ce

que le feu s’éteigne. En cas d’incendie incontrôlé,

appelez immédiatement le service d’incendie local.

Ne jamais mettre de l’eau sur un feu de graisse.

AVERTISSMENT CONCERNANT LE MONOXYDE DE CARBON

Avertissement concernant le monoxyde de carbone Respecter les présentes directives pour éviter de vous faire intoxiquer et

d’intoxiquer vos proches par ce gaz incolore et inodore. Vous devez connaître les symptômes d’une intoxication au monoxyde

de carbone : il s’agit de maux de tête, de vertiges, de faiblesses, de nausées, de vomissements, de somnolence et de

confusion. Le monoxyde de carbone réduit la capacité sanguine pour transporter l’oxygène. Un faible taux d’oxygène dans

le sang peut entraîner des pertes de connaissance, voire la mort. Consultez un médecin si vous ou autrui développez des

symptômes du rhume ou s’apparentant à la grippe en cuisinant à proximité de cet appareil. Une intoxication au monoxyde de

carbone, souvent confondue par erreur avec un rhume ou la grippe, est souvent détectée trop tard.

La consommation d’alcool ou de drogues renforce les effets de l’intoxication au monoxyde de carbone.

Le monoxyde de carbone est particulièrement toxique pour les femmes enceintes et leur fœtus, les jeunes enfants, les

personnes âgées, les fumeurs et les personnes souffrant de troubles sanguins ou circulatoires, comme l’anémie ou des

maladies cardiaques.

PG24SE-5

PIÈCES

0217-PG24SE-5-PARTS

PG24-70 (2)

GRILLE DE CUISSON

PG24-3 (1)

LÈCHEFRITE

PG24-4 (1)

DÉFLECTEUR DE CHALEUR

PG24-11 (1)

SEAU DE COLLECTE DES GRAISSES

BOULON M6 X 45 (4)

ÉCROU M6 (8)

RONDELLE FREIN M6 (14)

RONDELLE PLATE M6 (8)

PG24-44 (1)

THERMOMÈTRE

PG24-34 (1)

JOINT DU SYSTÈME

D'ALIMENTATION

RONDELLE PLATE M6 (2)

ÉCROU M6 (2)

RONDELLE FREIN M6 (2))

VIS À MÉTAUX M6 X 15 (12)

PG24LS-9 (2)

BOULON DE CHARNIÈRE AVEC ÉCROU

PG24LS-8 (2)

ENSEMBLE DE CHARNIÈRE

PG24LS-9 (2)

BOULON DE CHARNIÈRE AVEC ÉCROU

PG24LS-1 (2)

ROULETTE

PG24SE-1 (2)

AXE DE ROULETTE

ÉCROU BORGNE M8 (2)

RONDELLE PLATE M8 (2)

PG24SE-13 (1)

HOPPER ASM

097110 (2)

BOUCHON DU PIED DE 1,25 PO

PG24SE-4 (1)

PIED AVANT

PG24SE-5 (1)

PIED ARRIÈRE

PG24SE-6 (1)

SUPPORT DE PIED

PG24SE-7 (1)

GRILLE DES PIEDS

PG24LS-7 (1)

COUVERCLE DU BARBECUE

PZ90-2 (1)

THERMOMÈTRE DE LUXE DE 7,6 CM

PG24-54 (1)

COUVERTURE DE

LA SONDE

PG24LS-6 (1)

MANIPULER

PG24-41 (1)

BURNER PULLOUT

PG24-42 (1)

PULLOUT LOCK

PG24-9 (1)

BURNER PULLOUT KNOB

PG24-17 (1)

TASSE DE CENDRE

PG24-1 (1)

FACULTATIF

(NON INCLUS)

GRILLE DE

CONSERVATION

AU CHAUD

PG24SE-9 (1)

PG24SE-10 (1)

PG24-7 (1)

CHEMINÉE

ENSEMBLE DU CHAPEAU DE LA CHEMINÉE

BOULON 1/4-20 x 3 (1)

ÉCROU 1/4-20 (2)

JOINT DE LA CHEMINÉE

RONDELLE PLATE M6

RONDELLE FREIN M6 (2)

ÉCROU M6 (2)

HARDWARE KIT - PG24SE-12

CHIMNEY HARDWARE KIT - PG24-73

1114 PG2SE-2 PARTS

PG24-21 (1)

BOUGIE D'ALLUMAGE

PG24-22 (1)

VIS SANS FIN

DE TRANSPORT

PG24-23 (1)

DOUILLE DE LA VIS

SANS FIN DE TRANSPORT

PG24-24 (1)

MOTEUR DE LA VIS SANS FIN

PG24-25 (1)

AXE DE LA VIS SANS FIN

AVEC ÉCROU

PG24-26 (1)

MOTEUR DU SYSTÈME

DE VENTILATION

PG24-27 (1)

ROUE DU SYSTÈME

DE VENTILATION

VIS M4.2 X 10 (4)

PG24-45 (1)

JOINT DU PANNEAU

DE COMMANDE

PG24-51 (1)

PLAQUE DE PROTECTION

PG24LS-10 (1)

BRÛLEUR

PG24SE-3 (1)

PANNEAU DE COMMANDE

PG24-30 (1)

BOUTON DU PANNEAU DE COMMANDE

M4.2 X 10 SCREW (2)

PG24LS-11 (1)

COUVERCLE

DU RÉSERVOIR

VIS M6 X 15

ÉCROU M6 (2)

RONDELLE FREIN M6 (2)

RONDELLE PLATE M6 (2)

PG24-49 (1)

VENTILATEUR DE

LA VIS SANS FIN

PG24SE-8 (1)

CAISSON DU RÉSERVOIR

PG24-48 (1)

CORDON

D'ALIMENTATION

VIS M4.2 X 10 (4)

PG24-53 (1)

AUGER GARDE

PGC24-12 (1)

POIGNÉE DE TRÉMIE

1. NE PAS laisser l’appareil sans surveillance lorsqu’il

fonctionne. L’utilisateur est tenu de rester à proximité du

produit et de garder celui-ci dans son champ de vision

direct pendant toute la durée de son fonctionnement.

2. Tenir les enfants et animaux domestiques à l’écart du

brûleur en permanence.

3. La consommation d’alcool, ou de médicaments obtenus

ou non sur ordonnance, risque de diminuer votre faculté

de monter correctement l’appareil ou de l’utiliser en toute

sécurité.

4. Destiné à un usage EN PLEIN AIR uniquement. NE PAS

utiliser à l’intérieur d’un immeuble, d’un garage ou de

tout autre endroit fermé. NE PAS utiliser dans un véhicule

récréatif ou sur un bateau. NE JAMAIS utiliser cet appareil

comme système de chauffage.

5. Ne faire fonctionner cet appareil sous AUCUNE surface

surplombante. Conserver une distance minimale de

0.9 m (36 pi) entre les quatre côtés de l’appareil et

TOUTE construction. N’entreposer aucuns matériaux

combustibles et liquides inﬂammables, plantes et

herbes sèches, buissons, papiers et toiles à proximité de

l’appareil.

6. Cet appareil n’est pas destiné à un usage commercial.

7. Toujours laisser l’appareil refroidir avant de le recouvrir

de sa housse d’extérieur.

8. Toujours recouvrir l’appareil de sa housse d’extérieur

(lorsqu’elle est fournie) lorsque l’appareil ne sert pas.

9. Toujours débrancher le barbecue avant de le recouvrir de

la housse d’extérieur.

10. Utiliser uniquement sur une surface stable et non

combustible comme les briques, le béton ou la saleté.

N’utilisez pas cette application sur une surface qui

brûlera ou fondra comme du bois, de l’asphalte, du

vinyle ou du plastique.

11. Assurez-vous que le seau à graisse est en place avant

de démarrer le gril.

12. En cas d’incendie, placer le bouton de commande sur

la position SHUTDOWN, fermer le couvercle et le laisser

fermé jusqu’à extinction du feu. Lorsque le barbecue

aura refroidi, suivre les consignes de nettoyage avant la

prochaine utilisation.

13. Utiliser uniquement des granules de feuillu à usage

alimentaire qui sont fabriqués pour être utilisés dans

des barbecues à granules. L’utilisation de granules

de conifères ou de bois de chauffage annulera votre

garantie.

14. Ne pas laisser le réservoir à granules se vider

complètement de granules. Les granules peuvent être

ajoutés à tout moment. Le réservoir peut contenir

environ 8,2 kg de granules. La consommation de

granules variera considérablement en fonction de la

température ambiante ainsi que de la température de

cuisson.

15. Il vous est recommandé de ne pas entreposer les

granules dans leur réservoir pour des périodes

prolongées ; ils peuvent en effet absorber l’humidité de

l’air et obstruer la vis sans ﬁn de transport.

16. Garder le couvercle fermé pendant le fonctionnement

du barbecue. Le barbecue est conçu pour cuisiner en

gardant le couvercle fermé.

17. Ne pas utiliser d’accessoires dont l’utilisation n’est pas

indiquée avec cet appareil.

18. Ne jamais employer d’essence de carburant de lanterne

de type essence, de kérosène, de produit d’allumage

pour charbon ou de liquides semblables pour démarrer

ou raviver un feu dans cet appareil. Garder tous ces

liquides à bonne distance de l’appareil pendant qu’il est

en service.

19. Les cendres doivent être déposées dans un conteneur

métallique possédant un couvercle hermétique. Le

conteneur fermé qui contient les cendres doit être placé

sur une surface non combustible ou sur le sol, très

loin des matériaux combustibles jusqu’à l’élimination

déﬁnitive des cendres. Si les cendres sont destinées à

être enterrées dans le sol ou dispersées autrement sur

place, elles devraient être conservées dans le conteneur

jusqu’à ce qu’elles soient complètement refroidies.

20. La créosote – Formation et nécessité de la retirer.

Lors de leur lente combustion, les granules de bois

produisent du goudron et d’autres vapeurs organiques

qui, combinés à l’humidité rejetée, forment la créosote.

Les vapeurs de créosote se condensent dans les tuyaux

d’évacuation d’un four relativement froid et dans la

hotte de ventilation d’un foyer à combustion lente. Il

en résulte une accumulation de résidus de créosote

dans les tuyaux d’évacuation et la hotte de ventilation.

Une fois mise à feu, cette créosote produit un feu

brûlant. Le tuyau d’évacuation des graisses doit être

inspecté au moins deux fois par an pour déterminer si

une accumulation de graisse et/ou de créosote s’est

produite. Si tel est le cas, cette accumulation doit être

enlevée pour réduire le risque d’incendie.

DANGER

Ne pas effectuer de travaux sur le barbecue lorsque celui-

ci est branché. L’électrocution qui risquerait de se produire

pourrait entraîner le décès ou des blessures graves.

Consignes De Montage Des Pieds

Retirer toutes les pièces détachées se trouvant à l’intérieur

du barbecue et du réservoir.

Déposer par terre une couverture ou un morceau de carton

par terre pour protéger le barbecue.

Montage des pieds

Avec l’aide d’une autre personne, mettre le barbecue à

l’envers sur la couverture ou le carton. Les couvercles du

barbecue et du réservoir s’ouvriront lors de cette opération.

Veiller donc à ne pas les abîmer. Le barbecue risque

également de rouler sur son couvercle. Une personne devrait

donc le maintenir en place pendant que l’autre personne

monte les pieds ﬁxes et les roues.

1. Assembler les pieds comme indiqué à la Fig. 1 à l’aide de

six boulons M6 x 30 et de six rondelles freins. Remarque

: le pied le plus long s’attache le plus près du réservoir.

Serrer la quincaillerie manuellement.

BOULON M6 X 45

RONDELLE FREIN M6

Fig. 1

2. Attacher les deux supports des pied à ceux-ci comme

illustré à la Fig. 2 à l’aide de quatre boulons M6 x 45,

quatre rondelles plates M6, quatre rondelles freins M6 et

4 écrous M6. Serrer la quincaillerie manuellement.

3. Attacher la grille aux pieds comme indiqué à la Fig. 2 à

l’aide de quatre boulons M6 x 45, quatre rondelles plates

M6, quatre rondelles freins M6 et quatre écrous M6.

Serrer la quincaillerie manuellement.

RONDELLE PLATE M6

RONDELLE FREIN M6

ÉCROU M6

BOULON M6 X 50

RONDELLE FREIN M6

RONDELLE PLATE M6

BOULON M6 X 45

ÉCROU M6

Fig. 2

4. Monter les deux roulettes aux pieds comme illustré

à la Fig. 3 à l’aide de leurs deux axes, de 2 rondelles

plates M8 et de deux écrous borgnes M8. Serrer toute la

quincaillerie de l’axe avec une clé.

RONDELLE PLATE M8 (2)

ÉCROU BORGNE M8 (2)

AXE DE ROULETTE

Fig. 3

5. Avec l’aide d’une autre personne, remettre le barbecue

à l’endroit. Veiller à ce que les couvercles du réservoir et

du barbecue se referment lorsque le barbecue est posé à

l’endroit.

6. Resserrer toute la quincaillerie montée aux étapes

précédentes. Ne pas écraser les tubes en serrant

exagérément la quincaillerie.

Montage De La Cheminée Et De Son Chapeau

1. Monter la cheminée sur le barbecue comme indiqué à

la Fig. 4. S’assurer que le joint de la cheminée est placé

entre le barbecue et la cheminée.

2. Serrer toute la quincaillerie.

3. Placer le boulon 1/4-20 x 3 à travers le chapeau de la

cheminée et l’attacher au moyen d’un (1) écrou 1/4-

20. Visser un deuxième écrou sur le boulon en laissant

environ 3,8 cm à partir de l’extrémité supérieure du

chapeau. Visser l’ensemble du chapeau vers le bas dans

le support de la cheminée jusqu’à ce que l’écrou du bas

touche le support. Voir la ﬁgure 4.

4. Il est possible d’ajuster la hauteur du chapeau de la

cheminée en fonction de l’été et de l’hiver. En été, l’écart

doit être d’environ 3,8 cm. En hiver, l’écart doit être

La page charge ...

Camp Chef Smoke Pro PG24SE-5 Warning & Instruction Booklet

Marque: Camp Chef

Modèle: Smoke Pro PG24SE-5

Catégorie: Barbecues

Taper: Warning & Instruction Booklet

Télécharger le PDF

rapport

dans d''autres langues

English: Camp Chef Smoke Pro PG24SE-5

Camp Chef Smoke Pro PG24SE-5 Warning & Instruction Booklet

Camp Chef Smoke Pro PG24SE-5 Warning & Instruction Booklet

dans d''autres langues

Documents connexes

Autres documents