Maestro E206XT Manuel utilisateur

Marque: Maestro

Modèle: E206XT

Taper: Manuel utilisateur

E200 Series

Multimode LAN/WAN/Wi-Fi Router

Model names:E206XT

Technical information:

 GSM/GPRS/EDGE bands:850/900/1800/1900MHz

 GPRS class B, multislot class 10 operation

 EDGE multislot class 12 operation

 HSDPA bands: 800/850/1900/2100MHz

 Max. RF power output: 2W(850/900MHz),1W(1800/1900 MHz)

 SIM interface (2FF) 1.8V/3V, with support for MFF2 SIM

 Support data (dl/ul up to 14.4Mbps/5.76Mbps), SMS, gpsOne

Power requirement:

 Input voltage: 9V to 60VDC

 Rated current: 650mA

DC input

12V

24V

48V

Idle state

(Ethernet, Wi-Fi & Cellular n/c)

110mA

82mA

43mA

23mA

Ethernet connected

(Wi-Fi & Cellular n/c)

150mA

112mA

57mA

31mA

Ethernet & Wi-Fi connected

(Cellular n/c)

202mA

151mA

76mA

41mA

Ethernet & Wi-Fi connected

(Cellular standby)

222mA

167mA

84mA

46mA

Ethernet & Wi-Fi connected Cellular

(CDMA2000@23dBm)

610mA

450mA

220mA

115mA

Interface Connections:

 SIM holder

 RJ45 8P8C WAN connector

 RJ45 8P8C LAN connector

 Wi-Fi RP-SMA antenna connector (50Ω)

 Active GPS SMA antenna connector (50Ω)

 Cellular SMA antenna connector (50Ω)

 4-pin MicroFit Molex connector for power supply and DI/Os

 Reset button

Dimensions:

 Overall size: 83.9mm x 60mm x 25mm

 Weight:130g

Temperature range:

 Operating: -20°C ~ 60°C

 Storage: -40°C ~ 80°C

 Relative humidity: up to 95% without condensation

Optional Accessories:

 Ultra-wide band antenna – ACC-A22

 Wi-Fi antenna – ACC-A21

 Ethernet cable – ACC-CA29

 DIN Rail Mount–ACC-DIN

 Power cord with fuse – ACC-CA10

 Power supply Europe – ACC-PS01

 Power supply America – ACC-PS09

 Power supply Australia – ACC-PS10

 Power supply UK – ACC-PS11

Safety Precautions

 The modem generates radio frequency (RF) power. When using the

modem care must be taken on safety issues related to RF interference as

well as regulations of RF equipment.

 Do not use your phone in aircrafts, hospitals, petrol stations or in places

where using GSM products is prohibited.

 Be sure that the modem will not be interfering with nearby equipment. For

example: pacemakers or medical equipment. The antenna of the modem

should be away from computers, office equipment, home appliance, etc.

 An external antenna must be connected to the modem for proper operation.

Only use approved antennas with the modem. Please contact authorized

dealer on finding an approved antenna.

 Always keep the antenna with minimum safety distance of 26.6 cm or more

from human body.

 Do not put the antenna inside metallic box, containers, etc.

Using the modem in vehicle

 Check for any regulation or law authorizing the use of GSM in vehicle in

your country before installing the modem

 Install the modem by qualified personnel. Consult your vehicle dealer for

any possible interference of electronic parts by the modem.

 The modem should be connected to the vehicle’s supply system by using a

fuse-protected terminal in the vehicle’s fuse box.

 Be careful when the modem is powered by the vehicle’s main battery. The

battery may be drained after extended period.

Protecting your modem

 To ensure error-free usage, please install and operate your modem with

care.

Do remember the following:

 Do not expose the modem to extreme conditions such as high

humidity/rain, high temperatures, direct sunlight, caustic/harsh chemicals,

dust, or water.

 Do not try to disassemble or modify the modem. There is no user

serviceable part inside and the warranty would be void.

 Do not drop, hit or shake the modem. Do not use the modem under

extreme vibrating condition.

 Do not pull the antenna or power supply cable. Attach/ detach by holding

the connector.

 Connect the modem only according to the instruction manual. Failure to

do it will void the warranty.

 In case of problem, please contact authorized dealer.

DEALER’S CHOP

Federal Communications Commission (FCC)

Declaration of Conformity

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation.

This device has been tested and found to comply with the limits for a Class B

digital , pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiated radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:

Changes or modifications not expressly approved by the party responsible for

compliance could void the user‘s authority to operate the equipment.

Industry Canada Note

This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2) This device must accept any interference, including interference that may

cause undesired operation of the device .

Le présent appareil est conforme aux CNR d'Industrie Canada applicables

aux appareils radio exempts de licence. L'exploitation est autorisée aux deux

conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d'en

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du

Canada.

IC: 20055-E206XT

RF Exposure Information

This device meets the government’s requirements for exposure to radio

waves.

This device is designed and manufactured not to exceed the emission limits

for exposure to radio frequency (RF) energy set by the Federal

Communications Commission of the U.S. Government.

This device complies with FCC radiation exposure limits set forth for an

uncontrolled environment. In order to avoid the possibility of exceeding the

FCC radio frequency exposure limits, human proximity to the antenna shall

not be less than 20cm (8 inches) during normal operation.

IC Radiation Exposure Statement

Cet appareil est conforme aux limites d'exposition aux rayonnements de la IC

CNR-102 définies pour un environnement non contrôlé. Afin d'éviter la

possibilité de dépasser les limites d'exposition aux fréquences radio de la IC

CNR-102, la proximité humaine à l'antenne ne doit pas être inférieure à 20 cm

(8 pouces) pendant le fonctionnement normal.

Maestro E206XT Manuel utilisateur

Marque: Maestro

Modèle: E206XT

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Maestro E206XT User manual

Maestro E206XT Manuel utilisateur

Maestro E206XT Manuel utilisateur

dans d''autres langues

Autres documents