Hunter Fan 80210 Le manuel du propriétaire

Installation Guide

Model 80210 Bath Ventilator with Light

READ and SAVE THESE INSTRUCTIONS

43033-01 01/24/2008

FRANÇAIS

Consulter la page 23

ENGLISH

See page 2

ESPAÑOL

Vea la página 45

43033-01 01/24/2008

2

WARNING

!

WARNING

!

COOKING AREA

CAUTION

!

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

PREVENTATIVE MAINTENANCE

A clean fan provides better service. Disconnect the power supply and clean the

fan as listed below.

TO CLEAN GRILLE: Use a mild detergent, such as dishwashing liquid, and a

soft cloth. DO NOT use abrasive cloths, steel wool pads or scouring powders.

TO CLEAN FAN ASSEMBLY: Unplug motor cord from receptacle. To remove

motor plate, find the single tab on the motor plate (located next to the recepta-

cle). Push up rear motor plate tab while pushing out on the side of the housing

or insert a screwdriver into the slot in the housing (next to tab) and twist screw-

driver. Gently vacuum fan, motor and interior of housing.

METAL AND ELECTRICAL PARTS SHOULD NEVER BE IMMERSED IN

WATER.

MAINTENANCE

The motor is permanently lubricated and never needs oiling. If the motor bear-

ings are making excessive or unusual

noises, replace the motor with the exact service motor. You should replace the

impeller at the same time.

1. Use this unit only in a manner intended by the manufacturer. If

you have questions, contact the manufacturer.

2. Before servicing or cleaning the unit, switch power off at ser-

vice panel and lock the service disconnecting means to prevent

power from being switched on accidentally. when the service

disconnecting means cannot be locked, securely fasten a promi-

nent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by qualified

person(s) in accordance with all applicable codes and standards,

including fire-rated construction.

4. Sufficient air is needed for proper combustion and exhausting

of gasses through the flue (chimney) of fuel burning equipment

to prevent backdrafting. Follow the heating equipment manufac-

turer’s guideline and safety standards, such as those published

by the National Fire Prevention Association (NFPA), and the

American Society for Heating, Refrigeration and Air-Conditioning

Engineers (ASHRAE), and the local code authorities.

5. When cutting or drilling into wall(s) or ceiling, do not

damage electrical wiring or other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. If this unit is to be installed over a tub or shower, it must be marked as

appropriate for the application and be connected to a GFCI (Ground

Fault Circuit Interrupter) - protected branch circuit.

8. Never place a switch where it can be reached from a tub or shower.

9. Install fan at least 5 feet (1.52 m) above the floor.

10. This unit must be grounded.

11. Unit must not be installed in a ceiling thermally insulated to a value

greater than R40.

DISCONNECT ELECTRIC

POWER SUPPLY

AND LOCK OUT

SERVICE PANEL BEFORE

SERVICING UNIT

1. For general ventilating use only. Do not use to exhaust haz-

ardous or explosive materials and vapors.

2. To avoid motor bearing damage and noisy/unbalanced impel-

lers, keep drywall spray, construction dust, etc. off power

unit.

3. DO NOT install this product in a wall. This product is

designed for installation in ceilings up to a 12/12 pitch (45

degrees). Ductwork must point upward.

4. Please read specification label on product for further infor-

mation and requirements.

Do Not Install Above

Or Inside This Area

Cooking

Equipment

Floor

45° 45°

43033-01 01/24/2008

3

x2

D

E

F

G

H

I

L

M

N

95044-01-000

95029-01-000

75191-01-000

03242-07-133

98037-01

74508-03-133

98025-01

75184-01-133

Q

x4

*

NOTE:

Strain relief cable connector

must be installed. Not

Included.

A

B

C

Extra Screws

x2

I

3/8” Cable Connector

O

P

J

K

65219

66002-01

77539-01

98255-01

98044-01

77521-01

1

2

E

I

Turn off the power source.

Tools Needed.

Estimated assembly time: 30 to 60 minutes

Before Installation

Check all the parts.

If damaged, call

1-888-830-1326

for replacements.

Included.

Loosen screws.

NOTE: Remove all packing materials before installation.

43033-01 01/24/2008

4

5

4

7

G

8

F

H

E

3

6

Remove the motor/blower from the housing.

Remove the pre-loaded screw tip covers.

Remove the wiring cover screw.

Back out the pre-loaded screw tips until flush

with the side of the housing.

Remove the wiring cover.

Remove packing material.

43033-01 01/24/2008

5

9

E

10

B

C

E

A11

5/8

1/2

A12

Pop out the first wiring access slug. Use second if

needed.

Insert the strain relief into the housing and

secure with the washer.

Position the correct depth mark at the bottom edge of

the joist based on the thickness of your sheetrock.

New Construction – attaching to joist

Choose Installation Option

For New Construction - attaching to joist go to step A11, page 5

For New Construction - suspended between joists go to step B11, page 8

For Existing Construction - accessible from above go to step C11, page 11

For Existing Construction - accessible only from below go to step D11,

page15

Screw pre-loaded screws into joist or framing.

43033-01 01/24/2008

6

A

3 Pin

2 Pin

Fan Motor

Light

Green

Black

White

Black

White

Bare Copper

Ground

A14

Main Switch 1 (AC In)

Switch 2 (AC In)

*Option Fan & Main Light Together

*Option

A13



A16

Connect 4” duct and vent to the outside. Tape joints.

If ducting does not fit securely, an adapter may need

to be purchased.

A15

E

F

G

Install the wiring cover plate. Make sure all

wiring connections are inside the box or under

the wiring cover plate.

Connect wires as shown.

Pull wires through the strain relief.

43033-01 01/24/2008

7

A19

I

A20

Connect wiring from the motor to the wiring cover

plate.

0000

A17

0000

H

A18

ON

OFF

A21

A2 2

E1

Go to step

on page 17

to attach grille.

Reinstall the motor by inserting the tabs and pushing

up into position. Make sure the wires are not pinched

between the motor and the housing.

Secure the motor by tightening the 2 screws.

Turn on the power source.

Test the motor. If the motor does not run, check the

plug connection.

43033-01 01/24/2008

8

B11

D

E

5/8

1/2

5/8

1/2

B12

1/8" Bit

B14

B15

B16

E

B13

Slide the mounting rails into brackets.

Mark position of screws by using holes as a template.

Insert screws, leaving space between the screw

head and the joist. Screws are not provided.

New Construction – suspended between joists

Position the correct depth mark at the bottom edge of

the joist based on the thickness of your sheetrock.

Drill a hole in the center of each outline.

Attach the rails onto the screws.

43033-01 01/24/2008

9

B17

B18

Connect wires as shown.

A

3 Pin

2 Pin

Fan Motor

Light

Green

Black

White

Black

White

Bare Copper

Ground

B19

Main Switch 1 (AC In)

Switch 2 (AC In)

*Option Fan & Main Light Together

*Option

B21

Connect 4” duct and vent to the outside. Tape joints.

If ducting does not fit securely, an adapter may need

to be purchased.

Install the wiring cover plate. Make sure all wiring

connections are inside the box or under the

wiring cover plate.

F

G

B20

Tighten screws. Pull wires through the strain relief.

43033-01 01/24/2008

10

B27

E1

Go to step

on page 17

to attach grille.

B22

H

Connect wiring from the motor to the wiring cover

plate.

H

B23

Reinstall the motor by inserting the tabs and pushing

up into position. Make sure the wires are not pinched

between the motor and the housing.

B25

Turn on the power source.

ON

OFF

B26

Test the motor. If the motor does not run,

check the plug connection.

B24

I

Secure the motor by tightening the 2 screws.

43033-01 01/24/2008

11

C12

D

E

EXISTING FAN

C11

NO EXISTING FAN

8”

8.5”

5/8

1/2

5/8

1/2

C13

C14

Existing Construction – accessible from above

OR

Remove an existing fan and check to make sure the

opening is large enough to accommodate the new

motor housing (8”x 8.5”).

Cut out an opening for the housing.

Use the motor housing as a template to mark position.

Slide the mounting rails into brackets.

Position the correct depth mark at the bottom edge of

the joist based on the thickness of your sheetrock.

Mark position of screws by using holes as a template.

43033-01 01/24/2008

12

C15

1/8" Bit

C16

C17

C18

C19

C20

Drill a hole in the center of each outline. Insert screws, leaving space between the screw head

and the joist. Screws are not provided.

Attach the rails onto the screws. Tighten screws.

Connect 4” duct and vent to the outside. Tape joints.

If ducting does not fit securely, an adapter may

need to be purchased.

Pull wires through the strain relief.

43033-01 01/24/2008

13

C21

A

3 Pin

2 Pin

Fan Motor

Light

Green

Black

White

Black

White

Bare Copper

Ground

C22

Main Switch 1 (AC In)

Switch 2 (AC In)

*Option Fan & Main Light Together

*Option

C24

H

G

F

C23

Tighten the strain relief screws.

Connect wires as shown.

Install the wiring cover plate. Make sure all wiring

connections are inside the box or under the

wiring cover plate.

Connect wiring from motor the motor

to the wiring cover plate.

43033-01 01/24/2008

14

C25

H

C26

I

C27

ON

OFF

C2 8

C2 9

E1

Go to step

on page 17

to attach grille.

Secure the motor by tightening the 2 screws.

Reinstall the motor by inserting the tabs and pushing

up into position. Make sure the wires are not pinched

between the motor and the housing.

Turn on the power source. Test the motor. If the motor does not run,

check the plug connection.

43033-01 01/24/2008

15

EXISTING FAN

D11

E

D12

D13

2

1

D14

E

D15

Existing Construction – accessible only from below

Pull wires through strain relief.

Remove an existing fan and check to make sure the

opening is large enough to accommodate the new

motor housing (8”x 8.5”).

Move the housing into position above the ceiling.

Attach existing ducting to duct connector. Tape joints.

If ducting does not fit securely,

an adapter may need to be purchased.

Install the housing flush with the sheetrock and secure

by tightening the pre-loaded screws into the joist.

43033-01 01/24/2008

16

H

D18

H

D19

D20

I

A

3 Pin

2 Pin

Fan Motor

Light

Green

Black

White

Black

White

Bare Copper

Ground

D16

Main Switch 1 (AC In)

Switch 2 (AC In)

*Option Fan & Main Light Together

*Option

F

D17

G

Reinstall the motor by inserting the tabs and pushing

up into position. Make sure the wires are not pinched

between the motor and the housing.

Connect wiring from the motor to the wiring cover

plate.

Secure the motor by tightening the 2 screws.

Connect wires as shown.

Install the wiring cover plate.

43033-01 01/24/2008

17

ON

OFF

D22

D23

E1

Go to step

on page 17

to attach grille.

D21

K

E1

Test the motor. If the motor does not run, check the

plug connection.

Turn on the power source.

Attaching the Dome Assembly

Remove the thumbscrews.

L

E2

Connect wiring harness.

43033-01 01/24/2008

18

E6

E8

E7

M

Attach thumbscrews.

WARNING: To reduce the risk of electrical shock,

all 4 thumbscrews MUST be properly installed.

Install 2 Max 60 Watt A15 bulbs (Not Included).

E4

J

E5

Align posts A, B, C and D (stamped into motor housing)

with posts A, B, C and D (stamped into light fixture).

Slide light fixture over posts.

Remove the strain relief bracket screw.

Position the strain relief bracket under the motor as

shown.

Insert the strain relief bracket’s dog-leg tab so that it

hooks over the lip of the motor. Reinstall the strain

relief bracket screw.

E3

K

43033-01 01/24/2008

19

L

E10

Assemble the grille, glass dome, washer, and barrel

nut as shown. Tighten the barrel nut “finger-tight.”

NOTE: The washer must be oriented as shown.

Screw the dome assembly dome into position.

E9

Complete.

43033-01 01/24/2008

20

Trouble Shooting

Problem: Fan does not come on.

Solution:

• Harbor Breeze Fan Bath Ventilators are extremely quiet. To conrm that the fan is running, place

your hand near the vents to feel the air movement.

• Turn power on, replace fuse, or reset breaker.

• Check all plug connections to be sure they are secure.

• Check the wiring to make sure it matches the wiring diagram.

Problem: Light does not come on.

Solution:

• Replace the light bulb with a new bulb.

• Turn power on, replace fuse, or reset breaker.

• Check all plug connections to be sure they are secure.

• Check the wiring to make sure it matches the wiring diagram.

Problem: Fan is noisy.

Solution:

• Check and tighten all fasteners.

• Check the glass to make sure it is secure.

• Check the apper to make sure it moves freely.

If you need parts or service assistance, please call 866-405-3814.

La page charge ...

Hunter Fan 80210 Le manuel du propriétaire

Hunter Fan 80210 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents