Maytag MGD6300TQ - Bravos Gas Dryer Mode d'emploi

Catégorie
Sèche-linge électriques
Taper
Mode d'emploi
IVI&YI-'AG®
BRAVOS _
FABRIC
USE
CARE SYSTEM GAS
& CARE GUIDE
DRYER
p
SECHEUSE
A GAZ BRAVOS _ AVEC
DE SOIN DES TISSUS
.%
SYSTEME
GUIDE D'UTILISATION ET D'ENTRETIEN
FOR QUESTIONS ABOUT FEATURES, OPERATION/PERFORMANCE, PARTS, ACCESSORIES OR SERVICE
CAI.I.: 1.800.688.9900
IN CANADA, CAI.I.: 1.800.807.6777
VISIT OUR WEBSITE AI- WWW.MAYTAG.COM
IN CANADA, WWW.MAYTAG.CA
AU CANADA, POUR ASSISTANCE, INSTAI.I.ATION OU SERVICE, COMPOSEZ I.E : 1.800.807.6777
OU VISITEZ NOTRE SITE INTERNET ,_
WWW.MAYTAG.CA
PARA OBTENER ACCESO AI. MANUAl. DE USO Y CUIDADO EN ESPAIqOI., O PARA OBTENER INFORMACION ADICIONAI. ACERCA DE SU PRODUCTO, VISITE: WWW.MAYTAG.COM
TENGA I.ISTO SU N(JMERO DE MODEI.O COMPI.ETO. PUEDE ENCONTRAR El. N(JMERO DE MODEI.O Y DE SERIE DENTRO DE I.A CAVIDAD SUPERIOR DE I.A PUERTA.
W10150660A
iliiiiiiiiiiiiiiiiiiiiiiiiiiilil!i!i!i!i!i!i!i!iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii!iiiiii//liliiii_iiii_iiii_iiii_iiii_iiii_iiii_iiii_iiii_iiii_iiii_iiii_iiiiii_iiiiii_iiiiiIi_iiiiiiiiiiiiliiii_iiiiiiiii_iiiiiiiii_iiiiiiiii_iiiiiiiiiiiiIiiiiiiiiiiiiiiiiiiilliiiiii:iiiiiii!!iiiil¸¸_iiiiiii_iii_ii_.....................................................................ii_iiiiiiiiiiiiiiiiiiiii_iiiiiiiiiiliiiiiiiiiiiiliiiiiiiiiiiIiiiiiiiiiiii_i_iiiii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiliiiiiiiiiiiliii_i_iiiii_i_iliii__iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
TABLE OF CONTENTS
DRYER SAFETY ........................................................................................................................ 3
INSTALLATION INSTRUCTIONS ........................................................................................... 5
Tools and Parts ..................................................................................................................... 5
I.ocation Requirements ........................................................................................................ 5
Electrical Requirements ........................................................................................................ 7
Gas Supply Requirements .................................................................................................... 7
Venting Requirements .......................................................................................................... 8
Plan Vent System ............................................................................................................... 10
Install Vent System ............................................................................................................ 11
Install I_eveling I.egs .......................................................................................................... 11
Make Gas Connection ....................................................................................................... 12
Connect Vent .................................................................................................................... 12
I.eve[ Dryer ....................................................................................................................... 12
Reverse Door Swing .......................................................................................................... 13
Complete Installation ........................................................................................................ 15
DRYER USE ........................................................................................................................... 16
Starting Your Dryer ............................................................................................................ 16
Stopping, Pausing or Restarting ......................................................................................... 17
Drying and Cycle Tips ....................................................................................................... 17
Status I_ights ....................................................................................................................... 18
Cycles ............................................................................................................................... 18
Modifiers ........................................................................................................................... 19
Options ............................................................................................................................. 20
End of Cycle Signal ........................................................................................................... 20
Changing Cycles, Modifiers and Options .......................................................................... 20
Drying Rack Option .......................................................................................................... 21
DRYER CARE ........................................................................................................................ 22
Cleaning the Dryer I.ocation ............................................................................................. 22
Cleaning the I_int Screen ................................................................................................... 22
Cleaning the Dryer Interior ................................................................................................ 22
Removing Accumulated I_int ............................................................................................. 23
Vacation and Moving Care ............................................................................................... 23
Changing the Drum Light .................................................................................................. 23
TROUBLESHOOTING .......................................................................................................... 24
ASSISTANCE OR SERVICE .................................................................................................... 26
ACCESSORIES ...................................................................................................................... 26
WARRANTY ......................................................................................................................... 27
TABLE DES MATIERES
SI_CURITI_ DE LA SI_CHEUSE ................................................................................................. 29
INSTRUCTIONS D'INSTALLATION ..................................................................................... 31
Outillage et pi_ces ............................................................................................................. 31
Exigences d'emp[acement .................................................................................................. 31
Sp6cifications 6lectriques ................................................................................................... 33
A[imentation en gaz ........................................................................................................... 33
Exigences concernant ['6vacuation .................................................................................... 35
P[anification du syst_me d'6vacuation ............................................................................... 36
Installation du syst_me d'6vacuation .................................................................................. 38
Installation des pieds de nivellement .................................................................................. 38
Raccordement au gaz ......................................................................................................... 38
Raccordement du conduit d'6vacuation ............................................................................. 39
R6g[age de ['aplomb de [a s6cheuse ................................................................................... 39
Inversion du sens d'ouverture de [a porte ........................................................................... 40
Achever ['installation .......................................................................................................... 42
UTILISATION DE LA SI_CHEUSE ........................................................................................... 43
Mise en marche de [a s6cheuse .......................................................................................... 43
Arr_t, pause ou remise en marche ...................................................................................... 44
Consei[s pour [e s6chage et [es programmes ...................................................................... 45
T6moins [umineux .............................................................................................................. 45
Programmes ....................................................................................................................... 46
Modificateurs ..................................................................................................................... 47
Options .............................................................................................................................. 48
Signal de fin de programme ............................................................................................... 48
Changement des programmes, modificateurs et options .................................................... 48
Option de grille de s6chage ............................................................................................... 49
ENTRETIEN DE LA SI_CHEUSE .............................................................................................. 50
Nettoyage de ['emplacement de Has6cheuse ...................................................................... 50
Nettoyage du filtre _ charpie .............................................................................................. 50
Nettoyage de ['int6rieur de Has6cheuse .............................................................................. 51
Retrait de Hacharpie accumul6e ......................................................................................... 51
Pr6cautions _ prendre pour [es vacances et avant un d6m6nagement ................................ 51
Changement de ['ampoule d'6clairage du tambour ............................................................ 51
DI_PANNAGE ........................................................................................................................ 52
ASSISTANCE OU SERVICE .................................................................................................... 54
ACCESSOI RES........................................................................................................................ 54
GARANTIE ............................................................................................................................. 55
2
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
WARNING: For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, or to prevent property damage, personal injury, or death.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance,
- WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Clear the room, building, or area of all occupants.
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency, or
the gas supplier.
3
In the State of Massachusetts, the following installation instructions apply:
m Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by
the State of Massachusetts.
m If using a ball valve, it shall be a T-handle type.
m A flexible gas connector, when used, must not exceed 3 feet.
IM PORTANT SAFETY INSTRUCTIONS
WAR NiNG" To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,
including the following:
[] Read all instructions before using the dryer.
[] Do not place items exposed to cooking oils in your dryer.
Items contaminated with cooking oils may contribute to
a chemical reaction that could cause a load to catch fire.
[] Do not dry articles that have been previously cleaned in,
washed in, soaked in, or spotted with gasoline, dry-
cleaning solvents, or other flammable or explosive
substances as they give off vapors that could ignite or
explode.
[] Do not allow children to play on or in the dryer. Close
supervision of children is necessary when the dryer is
used near children.
[] Before the dryer is removed from service or discarded,
remove the door to the drying compartment.
[] Do not reach into the dryer if the drum is moving.
[] Do not install or store the dryer where it will be exposed
to the weather.
[] Do not tamper with controls.
[] Do not repair or replace any part of the dryer or attempt
any servicing unless specifically recommended in this
Use and Care Guide or in published user-repair
instructions that you understand and have the skills to
carry out.
[] Do not use fabric softeners or products to eliminate static
unless recommended by the manufacturer of the fabric
softener or product.
[] Do not use heat to dry articles containing foam rubber or
similarly textured rubber-like materials.
[] Clean lint screen before or after each load.
[] Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint, dust,
and dirt.
[] The interior of the dryer and exhaust vent should be
cleaned periodically by qualified service personnel.
[] See installation instructions for grounding requirements.
SAVE THESE INSTRUCTIONS
iMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1.
The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National
Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.
4 .....
iiiiii1_i_)iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_;_)i_iii)ii)i)//li;¸););_ii¸);_)iilii_)iilii_)iiiiili;_ii¸;);_ii¸;;iliiiii;iiiiiiil;iiiiil;iiiii::ii;;iiii))iiiii))))iii¸ :_)i_i_i_i_i_i_iiiii_))i_iiiiii_))i_iiiiii_))i_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiii(i_i}1i_II_i;¸););_ii¸);_ii¸);_ii¸);_)iilii_)iiii))))iiiiiii)iiii)iiii)iiii)iiii)iiii)iiii)iiii_iiii)i)//li;¸);iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_!i!)
INSTALLATION INSTRUCTIONS
Gather the required tools and parts before starting installation. Read and follow the
inshuctions provided with any tools listed here.
8" or 10" pipe wrench V4" nut driver or socket
wrench
8" or 10" adjustable
wrench (for gas Knife
connections)
Vent clamps
Flat-blade screwdriver
Pipe-joint compound
Adjustable wrench that resistant to I.P gas
opens to 1" (2.5 cm) or
hex-head socket wrench
(for adjusting dryer feet)
I.evel
Caulking gun and
compound (for installing
new exhaust vent)
Pliers
Parts supplied:
Remove parts package from dryer drum. Check that all parts were included.
4 leveling legs
Parts needed:
Check local codes and consult gas supplier. Check existing gas supply, electrical supply and
venting, and read "Electrical Requirements," "Gas Supply Requirements" and "Venting
Requirements" before purchasing parts.
Mobile home installations require special parts (listed following) that may be ordered by
calling the dealer from whom you purchased your dryer. For information on ordering, please
refer to the "Assistance or Service" section. You may also contact the dealer from whom you
purchased your dryer.
Mobile home installation kit. Ask for Part Number 346764.
Metal exhaust system hardware.
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Place dryer at least 18 inches (46 cm) above the floor
for a garage installation.
Failure to do so can result in death, explosion, or fire.
You will need
A location that allows for proper exhaust installation. See "Venting Requirements."
A separate 30-amp circuit.
A grounded electrical outlet located within 2 ft (61 cm) of either side of the dryer. See
"Electrical Requirements."
A sturdy floor to support the total weight (dryer and load) of 200 Ibs (90.7 kg). The
combined weight of a companion appliance should also be considered.
A level floor with a maximum slope of 1" (2.5 cm) under entire dryer.
Do not operate your dryer at temperatures below 45°t: (7°C). At lower temperatures, the dryer
might not shut off at the end of an automatic cycle. Drying times can be extended.
The dryer must not be installed or stored in an area where it will be exposed to water and/or
weather.
Check code requirements. Some codes limit, or do not permit, installation of the dryer in
garages, closets, mobile homes or sleeping quarters. Contact your local building inspector.
NOTE: No other fuel-burning appliance can be installed in the same closet as a dryer.
InstallationClearances
The location must be large enough to allow the dryer door to open fully.
Dryer Dimensions
cm)
*Most installations require a minimum 5" (12.7 cm) clearance behind the dryer for the
exhaust vent with elbow. See "Venting Requirements."
Installation spacing for recessed area or closet installation
The following spacing dimensions are recommended for this dryer. This dryer has been tested
for spacing of O" (O cm) clearance on the sides and rear. Recommended spacing should be
considered for the following reasons:
Additional spacing should be considered for ease of installation and servicing.
Additional clearances might be required for wall, door and floor moldings.
Additional spacing should be considered on all sides of the dryer to reduce noise transfer.
For closet installation, with a doo_; minimum ventilation openings in the top and bottom
of the door are required. I.ouvered doors with equivalent ventilation openings are
acceptable.
Companion appliance spacing should also be considered.
Additional spacing is required if you exhaust out the rear of the dryer to either the right or
left side.
_r 3"*
(310cm2)!
24in'2'JJ 3"*
(155cm2qI_" I-'_.6cm)
1"_ I_ 29"_ _1" _11"*1_ 29,/,"_1s"÷ -T
(2.5cm) (73.7crn) (2,5crn) (2.5cm)(74,3crn)(12.7crn)
A B C
A. Recessed area
B. Side view - closet or confined area
C. Closet door with vents
*Required spacing
Mobile home - Additional installation requirements
This dryer is suitable for mobile home installations. The installation must conform to the
Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the
Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280) or
Standard CAN/CSA-Z240 MH.
Mobile home installations require:
Metal exhaust system hardware, which is available for purchase from your dealer.
Mobile home Installation Kit Part Number 346764. See "Tools and Parts" section for
information on ordering.
Special provisions must be made in mobile homes to introduce outside air into the dryer.
The opening (such as a nearby window) should be at least twice as large as the dryer
exhaust opening.
6
ect cat
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
120 Volt, 60 Hz., AC only, 15- or 20-amp fused electrical supply is required. A time-delay
fuse or circuit breaker is recommended. It is also recommended that a separate circuit
serving only this dryer be provided.
GROUNDING iNSTRUCTiONS
For a grounded, cord-connected dryer:
This dryer must be grounded, in the event of malfunction or
breakdown, grounding will reduce the risk of electric shock
by providing a path of least resistance for electric current.
This dryer is equipped with a cord having an equipment-
grounding conductor and a grounding plug. The plug must
be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes
and ordinances.
WARNING: improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service representative
or personnel if you are in doubt as to whether the dryer is
properly grounded. Do not modify the plug provided with the
dryer: if it will not fit the outlet, have a proper outlet installed
by a qualified electrician.
SAVE THESE INSTRUCTIONS
Explosion Hazard
Use a new CSA International approved gas supply line.
install a shut=off valve.
Securely tighten all gas connections.
if connected to LP, have a qualified person make sure
gas pressure does not exceed 13" (33 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
Gas Type
Natural Gas:
This dryer is equipped for use with Natural gas. It is design-certified by CSA International for
I.P (propane or butane) gases with appropriate conversion.
Your dryer must have the correct burner for the type of gas in your home. Burner
information is located on the rating plate in the door well of your dryer. If this information
does not agree with the type of gas available, contact your dealer or call the phone
numbers referenced on the front page of this manual.
LP gas conversion:
Conversion must be made by a qualified technician.
No attempt shall be made to convert the appliance from the gas specified on the model/serial
rating plate for use with a different gas without consulting your gas company. For information
on ordering an LP conversion kit, please refer to the "Assistance or Service" section. Ask for
Part Number 49572.
Gas Supply Line:
Must include Vs" NPT minimum plugged tapping accessible for test gauge connection,
immediately upstream of the gas connection to the dryer (see illustration).
V2" IPS pipe is recommended.
3/811approvedaluminumorcoppertubingisacceptableforlengthsunder20ft(6.1m)if
localcodesandgassupplierpermit.
IfyouareusingNaturalgas,donotusecoppertubing.
3/8"flarex3/8"NPTadapterfittingbetweendryerpipeand3/8"approvedtubing.
I.engthsover20ft(6.1m)shoulduselargertubingandadifferentsizeadapterfitting.
Ifyourdryerhasbeenconvertedtouse12gas,3/8"12compatiblecoppertubingcanbe
used.Ifthetotallengthofthesupplylineismorethan20ft(6.1m),uselargerpipe.
NOTE:Pipe-jointcompoundsthatresisttheactionofI.Pgasmustbeused.Donotuse
TEFI.ON_'>_tape.
Mustincludeashutoffvalve:
IntheU.S.A.:
Anindividualmanualshutoffvalvemustbeinstalledwithinsix(6)feet(1.8m)ofthedryer
inaccordancewiththeNationalFuelGasCode,ANSIZ223.1.
InCanada:
AnindividualmanualshutoffvalvemustbeinstalledinaccordancewiththeB149.1,
NaturalGasandPropaneInstallationCode.Itisrecommendedthatanindividualmanual
shutoffvalvebeinstalledwithinsix(6)feet(1.8m)ofthedryer.
Thelocationshouldbeeasytoreachforopeninganddosing.
A C E
B D
A. aM"flexible gas connector
B. aM,,pipe to flare adapter fitting
C. _" NPT minimLIm plugged tapping
D. 7/,,, NPT gas supply line
E. Gas shutoff valve
Gas supply connection requirements
Use an e[bow and a 3/811f[are x 3/811NPTadapter fitting between the f[exib[e gas connector
and the dryer gas pipe, as needed to avoid kinking.
Use only pipe-joint compound. I)o not use TEFI.ON <_÷tape.
This dryer must be connected to the gas supply line with a listed flexible gas connector
that complies with the standard for connectors for gas appliances, ANSI Z21.24 or CSA
6.10.
Burner Input Requirements:
Elevations above 10,000 ft (3,048 m):
When insta[[ed above 10,000 ft (3,048 rn) a 4% reduction of the burner Btu rating shown
on the model/serial number plate is required for each 1,000 ft (305 m) increase in
elevation.
Gas Supply Pressure Testing
The dryer must be disconnected from the gas supply piping system during pressure testing
at pressures greater than 1/2psi.
Dryer Gas Pipe
The gas pipe that comes out through the rear of your dryer has a 3/811rna[e pipe thread.
A j.._,.j/,,.JT"Y_
(1.9 cm)
A. 3/8" NPT dryer pipe
Fire Hazard
Use a heavy metal vent.
Do not use a plastic vent.
Do not use a metal foil vent.
FaUure to follow these instructions can result in death
or fire.
WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS.
IMPORTANT: Observe all governing codes and ordinances.
The dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling or a
concealed space of a building.
t®TEFI ON is a registered trademarl< of E.I. Du Pont De Nemours and Company.
8 .....
If using an existing vent system
Clean lint from the entire length of the system and make sure exhaust hood is not plugged
with [int.
Replace any plastic or metal foil vent with rigid or flexible heavy metal vent.
Review Vent system chart. Modify existing vent system if necessary to achieve the best
drying performance.
If this is a new vent system
Vent material
Use a heavy metal vent. Do not use plastic or metal foil vent.
4" (1 0.2 cm) heavy metal exhaust vent and clamps must be used.
4" (10.2 cm) heavy metal exhaust vent
Vent products can be purchased from your dealer or by calling Maytag Services. For more
information, see the "Assistance or Service" section.
Rigid metal vent
For best drying performance, rigid metal vents are recommended.
Rigid metal vent is recommended to avoid crushing and kinking.
Flexible metal vent
Flexible metal vents are acceptable only if accessible for cleaning.
Flexible metal vent must be fully extended and supported when the dryer is in its final
location.
Remove excess flexible metal vent to avoid sagging and kinking that may result in
reduced airflow and poor performance.
Do not install flexible metal vent in enclosed walls, ceilings or floors.
Elbows
45 ° elbows provide better airflow than 90 ° elbows.
Good
Better
Clamps
Use clamps to seal all joints.
Exhaust vent must not be connected or secured with screws or other fastening devices
that extend into the interior of the duct. Do not use duct tape.
Clamp
Exhaust
Recommended hood styles are shown here.
B
(10.2 em)
A. Louvered hood style
B.Box hood style
The angled hood style (shown here) is acceptable.
(6.4 era)
An exhaust hood should cap the vent to keep rodents and insects from entering the home.
Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that may be in
the path of the exhaust (such as flowers, rocks or bushes, snow line, etc.).
Do not use an exhaust hood with a magnetic latch.
improper venting can cause moisture and lint to collect
indoors, which may result in:
[] Moisture damage to woodwork, furniture, paint, wallpaper,
carpets, etc.
[] Housecleaning problems and health problems.
Choose your exhaust installation type
Recommended exhaust installations
Typical installations vent the dryer from the rear of the dryer.
A -- f
A. Dryer
B.Elbow
C. Waft
D. Exhaust hood
E. Clamps
£ Rigid metal or flexible metal vent
G. Vent length necessary to connect elbows
H. Exhaust outlet
Standard exhaust installation with rigid metal or flexible metal vent
Alternate installations for close clearances
Venting systems come in many varieties. Select the type best for your installation. Two close-
clearance installations are shown. Refer to the manufacturer's instructions.
B
.,]-T 7-I-
L: i L]! 1Lt
]Z _ L
C
A. Over-the-top installation (also available with one
offset elbow)
B. Periscope installation
C. Rear exhaust installation to left or right side
NOTE: The following kits for close clearance alternate installations are available for purchase.
Please see the "Assistance or Service" section to order.
Over-the-Top Installation:
Part Number 4396028
Periscope Installation (For use with dryer vent to wall vent mismatch):
Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm) mismatch
Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm) mismatch
Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm) mismatch
Rear exhaust installation to [eft or right side:
Part Number 8212504
Special provisions for mobile home installations
The exhaust vent must be securely fastened to a noncombustible portion of the mobile home
structure and must not terminate beneath the mobile home. Terminate the exhaust vent
outside.
/
Determine vent path
Select the route that will provide the straightest and most direct path outdoors.
Plan the installation to use the fewest number of elbows and turns.
When using elbows or making turns, allow as much room as possible.
Bend vent gradually to avoid kinking.
Use the fewest 90 ° turns possible.
Determine vent length and elbows needed for best drying performance
Use the following Vent system chart to determine type of vent material and hood
combinations acceptable to use.
NOTE: Do not use vent runs longer than those specified in the Vent system chart. Exhaust
systems longer than those specified will:
Shorten the life of the dryer.
Reduce performance, resulting in longer drying times and increased energy usage.
The Vent system chart provides venting requirements that will help to achieve the best drying
performance.
Vent system chart
NOTE: Performance of rear exhaust to either side of the dryer is equivalent to adding one
elbow. To determine maximum exhaust length, add one elbow to the chart.
Number of Type of Box or Angled
90 ° turns vent Louvered hoods
or elbows hoods
O Rigid metal 64 ft (20 m) 58 ft (17.7 m)
Flexible metal 36 ft (11 m) 28 ft (8.5 m)
1 Rigid metal 54 ft (16.5 m) 48 ft (14.6 m)
Flexible metal 31 ft (9.4 m) 23 ft (7 m)
2 Rigid metal 44 ft (13.4 m) 38 ft (11.6 m)
Flexible metal 27 ft (8.2 m) 19 ft (5.8 m)
3 Rigid metal 35 ft (10.7 m) 29 ft (8.8 m)
Flexible metal 25 ft (7.6 m) 17 ft (5.2 m)
4 Rigid metal 27 ft (8.2 m) 21 ft (6.4 m)
Flexible metal 23 ft (7 m) 15 ft (4.6 m)
1,
2.
3.
Install exhaust hood. Use caulking compound to seal exterior wall opening around
exhaust hood.
Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust
hood with 4" (10.2 cm) clamp.
Run vent to dryer location. Use the straightest path possible. See "Determine vent path" in
"Plan Vent System." Avoid 90° turns. Use clamps to seal all joints. Do not use duct tape,
screws or other fastening devices that extend into the interior of the vent to secure vent.
Excessive Weight Hazard
Use two or more people to move and install dryer.
Failure to do so can result in back or other injury.
1. To protect the floor, use a large flat piece of cardboard from the dryer carton. Place
cardboard under the entire back edge of the dryer.
2. Firmly grasp the body of the dryer (not the top or console panel). Gently lay the dryer on
the cardboard. See illustration.
\\ ....................................
3. Examine the leveling legs. Find the diamond marking.
4. Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the
diamond marking is no longer visible.
5. Place a carton corner post from dryer packaging under each of the 2 dryer back corners.
Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location.
I.eave enough room to connect the exhaust vent or gas line.
For mobile home use
Gas dryers must be securely fastened to the floor.
Mobile home installations require a Mobile Home Installation Kit. See "Tools and Parts"
section for information on ordering.
1.
2.
Make Gas Con i: c I;o}"
Remove the red cap from the gas pipe.
Using a wrench to tighten, connect the gas supply to the dryer. Use pipe-joint compound
on the threads of all non-flared male fittings. If flexible metal tubing is used, be sure there
are no kinks.
A .......................................-_ ...............................B
A. fTared male thread
B.Non-flared male thread
NOTE: For I.P gas connections, you must use pipe-joint compound resistant to the action
of I.P gas. I])o not use TEFI.ON tape.
A combination of pipe fittings must be used to connect the dryer to the existing gas line.
Shown is a recommended connection. Your connection may be different, according to the
supply line type, size and location.
!
1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to
existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust
outlet and inside the exhaust hood. Check that the vent is secured to exhaust hood with a
4" (1 0.2 cm) clamp.
2. Move dryer into its final location. Do not crush or kink vent.
3. (On gas modeis) Check that there are no kinks in the flexible gas line.
4. Once the exhaust vent connection is made, remove the corner posts and cardboard.
Check the levelness of the dryer by first placing a level on the top of the dryer near the
conso[e.
Then, by placing a level in the crease on the side of the dryer between the top of the dryer and
the dryer cabinet, check the levelness from front to back.
3.
A
C
B
A. a_,,flexible gas connector
B. a_,,ctryer pipe
C. a_,,to a_,,pipe elbow
D. a_,,pipe-to-flare adapter fitting
Open the shutoff valve in the supply line. The valve is open when the handle is parallel to
the gas pipe.
If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs
up or clown and check again for levelness.
A. Closed valve
B. Open valve
Test all connections by brushing on an approved noncorrosive leak-detection solution.
Bubbles will show a leak. Correct any leak found.
t-_JFEF[ ON is a registered trademark of E.I. Du Pont De Nemours and Company.
12
Youcanchangeyourdoorswingfromaright-sideopeningtoaleft-sideopening,ifdesired.
1. Placeatowelorsoftclothontopofthedryerorworkspacetoprotectthesurface.
Removethedoorassembly
1. Openthedryerdoor.
2. Removethebottomscrewfromeachofthe2hingesthatattachthedryerdoortothefront
pane[ofthedryer.
3. I.oosenthetopscrewfromeachofthe2hingesinStep2.
5. Removethe4plasticplugslocatedoutsidethedryerdooropening.
I1
II
/4
B
./4
B
6. Install 4 plastic plugs into screw holes in the dryer [eft where the hinges were removed in
Step 4.
Reverse the strike
1. Remove the door strike from the dryer door opening.
2. Remove the cosmetic screw opposite the door strike.
4.
A. loosen these screws. A
B. Remove these screws.
Remove the dryer door and the hinges by lifting upward on the door. I.ay the door on a
flat, protected surface, with the inside of the door facing up. Remove remaining 2 loose
screws from dryer front panel.
Reinstall the door
1. Remove the 4 screws and 2 hinges from the dryer door.
3.
A. Door strike
B. Cosmetic screw
Reinstall the door strike and cosmetic screw on the opposite side of the dryer door
opening from where they were removed.
NOTE: Door strike and plugs must be on the same side of the dryer door opening.
2. Replace the 4 screws in the same holes.
3. Remove the 4 screws from the opposite side of the door.
\
!
I
I
Install the 2 hinges to the front panel of the dryer using 4 screws. Use the non-slotted side
to attach the hinge to the front panel.
5. Install screws in the top hinge holes in the door. I)o not tighten screws. I.eave
approximately '/4" (5 mm) of screw exposed.
A. Install these screws first.
Hang door by placing screw heads into top slotted holes of hinges and slide door down.
Align bottom screw holes in hinge and door. Install two bottom screws. Tighten all hinge
screws.
7. Close door to engage door strike.
14
1. Check that all parts are now installed. If there is an extra part, go back through the steps to
see which step was skipped.
2. Check that you have all of your tools.
3. Dispose of/recycle all packaging materials.
4. Check the dryer's final location. Be sure the vent is not crushed or kinked.
5. Check that the dryer is [eve[. See "l.eve[ Dryer."
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
7. Remove any protective film or tape remaining on the dryer.
NOTE: Glass door models have a protective film on the window that should be removed.
8. Read "Dryer Use."
9. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.
10. Test dryer operation by selecting a Timed Dry heated cycle and starting the dryer. For this
test, do not select the Air Fluff modifier.
If the dryer will not start, check the following:
Dryer is plugged into a grounded 3 prong outlet.
Electrical supply is connected.
Household fuse is intact and tight, or circuit breaker has not tripped.
Dryer door is closed.
11. When the dryer has been running for 5 minutes, open the dryer door and fee[ for heat. If
you fee[ heat, cancel cycle and close door. If you do not fee[ heat, turn off the dryer and
check that the gas supply line shutoff valve is open.
If the gas supply line shutoff valve is closed, open it, then repeat the 5-minute test as
outlined above.
If the gas supply line shutoff valve is open, contact a qualified technician.
6. Plug into a grounded 3 prong outlet. Turn on power.
DRYER USE
e c_L WRI_LECYCLES CYCLES
START
e UI_H @p
_MO_E _ MEDIUM LIGHT AUSE/
INORMAL ILOW H H CANCEL
I LESS I EXtrA OW
_Mp _LUFF WRINKL_
PrB/_NT
(9@ ®
DRY CYCLES MODIFIERS OPTIONS
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Do not dry anything that has ever had anything
flammable on it (even after washing).
Failure to follow these instructions can result in death,
explosion, or fire.
Fire Hazard
No washer can completely remove oil
Do not dry anything that has ever had any type of oil on
it (including cooking oils).
items containing foam, rubber, or plastic must be dried
on a clothesline or by using an Air Cycle.
Failure to follow these instructions can result in death
or fire.
This manual covers several different models. Your dryer may not have all of the cycles and
features described.
Follow these basic steps to start your dryen Please refer to specific sections of this manual for
more detailed information.
1. Clean lint screen before each load. See "Cleaning the Lint Screen."
2. Place laundry into dryer and shut door.
3. Press POWER.
4.
Turn the knob to the selected cycle. The preset settings for Sensor Dry Cycles or Timed
Cycles will illuminate. The estimated (automatic cycle) or actual (timed) cycle time (in
minutes) will show in the display.
NOTE: A default time is displayed when an automatic cycle is selected. During the first
few minutes of the drying process, the cycle time may automatically vary from the default
time based on the size and fabric type of the load. Toward the end of the drying process,
the estimated time display will adjust again, showing the final drying time.
16
To use a Sensor Dry Cycle
Press POWER.
Turn the knob to desired Sensor Dry Cycle.
Select I)RYNESS to adjust how dry you want the load. As the cycle runs, the control
senses the dryness of the load and adjusts the time automatically for the selected
dryness [eve[.
The default dryness setting is Normal when a Sensor Dry Cycle is selected. You can
select a different dryness level, depending on your load, by pressing Dryness and
choosing More, I.ess or Damp. Selecting More, I_essor Damp automatically adjusts
the sensed time needed. Once a dryness level is set, it cannot be changed without
stopping the cycle.
Select the desired Options.
To make changes during a Sensor Dry Cycle:
Press PAUSE/CANCEl .....
Adjust I)ryness.
MORE
NORMAL
_p• less
DRYNESS
ONlY
NOTE: I)ryness selections can be made only while using Sensor I)ry Cycles.
How the Sensi-Care TM Drying System Works
Moisture-sensing strips and temperature sensors inside the dryer drum monitor how fast
the load is drying, how hot the air should be and when clothes are dry. The system
automatically stops the cycle to help save time and avoid overdrying.
To use a Timed Cycle
Turn knob to desired Timed Cycle.
Press the TIMED CYCI.E ADJUST up or down arrows until the desired drying time is
displayed. Press the up or down arrows and the time will change by 1-minute
intervals. Press and hold the up or down arrows and the time will change by 5-minute
intervals.
NOTE: The Timed Cycle Adjust features can be used only with Timed Cycles.
®@
TIMED CYCLE
ADJUST
Press TEMP until the desired temperature illuminates.
MEDIUM
LOW
TEMP
ADJUST TIMED
CYCES
6.
NOTE: The Temp feature can be used only with Timed Cycles.
NOTE: I)uring a Timed Cycle, you can change the settings for Time, Temp, the Wrinkle
Prevent setting and the End of Cycle Signal
(OPTIONAl_ STEP) If desired, select OPTIONS. For more details, see "Options."
(OPTIONAl_ STEP) If desired, press ENID OF CYCI_E SIGNAl_. A signal will sound to alert
you when a cycle ends. For more details, see "End of Cycle SignaL"
Press START. Be sure the door is closed.
If you do not press Start within 5 minutes of selecting the cycle, the dryer
automatically shuts off.
If you wish to end your drying cycle after pressing Start, press PAUSE/CANCEl. twice.
_.,+,<_X)D }lls{:! _'_
I I ¢I
To stop or pause your dryer at any time
Open the door or press PAUSE/CANCEl once. Press PAUSE/CANCEl twice to cancel a cycle.
1O restart the dryer
Close the door. Press START until dryer starts.
NOTE: I)rying will continue from where the cycle was interrupted if you close the door and
press Start within 5 minutes. If the cycle is interrupted for more than 5 minutes, the dryer will
shut off. Select new cycle settings before restarting the dryer.
....F " b "' 'I '_='°
Select the correct cycle and dryness level or temperature for your load. If a Sensor I)ry Cycle
is running, the display shows the estimated cycle time when your dryer is automatically
sensing the dryness [eve[ of your load. If a Timed Cycle is running, the display shows the exact
number of minutes remaining in the cycle.
Coo[ I)own tumbles the load without heat during the last few minutes of all cycles. Coo[
I)own makes the loads easier to handle and reduces wrinkling. The length of the Coo[ I)own
depends on the load size and dryness [eve[.
Drying tips
Follow care [abe[ directions when they are available.
If desired, add a fabric softener sheet. Follow package instructions.
To reduce wrinkling, remove the load from the dryer as soon as tumbling stops. This is
especially important for permanent press, knits and synthetic fabrics.
Avoid drying heavy work clothes together with lighter fabrics. This could cause
overdrying of lighter fabrics and lead to increased shrinkage or wrinkling.
Cycle tips
Dry most loads using the preset cycle settings.
Refer to the Sensor Dry or Timed Preset Cycle Settings chart (in the "Cycles" section) for a
guide to drying various loads.
Drying temperature and dryness [eve[ are preset when you choose a Sensor Dry
Cycle. You can select a different dryness [eve[, depending on your load, by pressing
Dryness and choosing More, Normal I_essor Damp.
NOTE: You cannot use the Timed Cycle Adjust and you cannot choose a Temperature
with the Sensor Dry Cycles.
If you wish to adjust the cycle length of a Timed Cycle, press the Timed Cycle Adjust
up or down arrows. Adjust the temperature of a Timed Cycle by pressing Temp until
the desired temperature is selected.
NOTE: You cannot choose a dryness [eve[ with Timed Cycles.
Follow the progress of your dryer with the drying Status indicator lights.
COOL WRINKLE
SENSING WET DAMP DOWN DRY PREVENT
_0 Oj
Sensing
In a Sensor Dry Cycle, the Sensing light illuminates until a wet item is detected.
In a Timed Cycle, the Sensing light illuminates at the beginning of a cycle and turns off
5 minutes into the cycle.
Wet
The Wet light illuminates at the beginning of a Sensor Dry Cycle if a wet item is detected.
In a Sensor Dry Cycle, if a wet item is not detected after approximately 5 minutes, the
dryer goes directly into Coo[ Down. The Coo[ Down and the Wrinkle Prevent setting
indicators will illuminate, if selected.
In a Timed Cycle, wet items are not detected. The dryer will continue to run for the length
of time selected, and the Wet light will illuminate. The damp light will not illuminate.
Damp
The Damp light illuminates in a Sensor Dry Cycle when the laundry is approximately 80%
dry. Damp Dry Chime beeps, if selected. See "Options."
Cool Down
The Coo[ Down light illuminates during the coo[ down part of the cycle. I.aundry cools for
ease in handling.
Dry
The Dry light illuminates when the drying cycle is finished. This indicator stays on during the
Wrinkle Prevent setting.
Wrinkle Prevent Setting
The Wrinkle Prevent setting light illuminates when this option is selected. This indicator stays
on during the Wrinkle Prevent setting.
Indicator lights
Other indicator lights show Cycle, Modifiers, Options and Cycle Signal settings selected. The
display shows the estimated or actual time remaining.
Select the drying cycle that matches the type of load you are drying. See Sensor Dry or Timed
Preset Cycle Settings charts.
SENSOR DRY TIMED
CYCLES CYCLES
LFRESHEN
UP
DRY CYCLES
Sensor Dry Cycles
Sensor Dry Cycles allow you to match the cycle to the load you are drying. See the following
Sensor Dry Preset Cycle Settings chart. Each cycle dries certain fabrics at the recommended
temperature. A sensor detects the moisture in the load and automatically adjusts the drying
time for optimal drying.
Heavy Duty
Use this cycle to get high heat for heavyweight mixed loads, cottons and jeans.
Normal
Use this cycle to get medium heat for drying sturdy fabrics such as work clothes and sheets.
Wrinkle Control
Use this cycle to get low heat for drying no-iron fabrics, such as sport shirts, casual business
clothes and permanent press blends.
Delicate
Use this cycle to get extra-low heat to gently dry items such as lingerie, blouses or washable
knit fabrics.
Sensor Dry Preset Cycle Settings
Sensor Dry Cycles Temperature
Load Type
HEAVY DUTY High
Heavyweight mixed loads, cottons, jeans
NORMAL Medium
Corduroys, work clothes, sheets
WRINKLE CONTROL I.ow
Business casual clothes, permanent press, synthetics
DELICATE Extra-I_ow
Lingerie, blouses, washable knit fabrics
18 ....
Timed Cycles
Use Timed Cycles to select a specific amount of drying time and a drying temperature. When
a Timed Cycle is selected, the Estimated Time Remaining display shows the actual time
remaining in your cycle. You can change the actual time in the cycle by pressing the Timed
Cycle Adjust up or down arrows. See "Changing Cycles, Modifiers and Options."
NOTE: Timed Cycles may also be used with the dryer rack. See "Dryer Rack."
Timed Dry
Use this cycle to complete drying if items are still damp after a Sensor I)ry Cycle. Timed I)ry
is also useful for drying heavyweight and bulky items, such as bedspreads and work clothes.
I_ightweight garments, such as exercise wea_, can be dried using Timed Dry on a low
temperatu re setting.
Quick Dry
Use this cycle for drying small loads or loads that need a short drying time.
Freshen Up
Use this cycle to help smooth out wrinkles from such items as clothes packed in a suitcase or
items wrinkled from being [eft in the dryer too long.
Timed Preset Cycle Settings
Timed Cycles Default Default Time
Load Type Temperature (Minutes)
TIMED DrY High 40
Heavyweight, bulky items, work
clothes
QUICK DrY Medium 24
Small loads
FRESHEN UP Medium 20
Helps to smooth out wrinkles
Sensor Dry Cycle Modifiers
Use the DRYNESS button to select dryness levels for the Sensor I)ry Cycles. Press DRYNESS
until the desired Dryness setting illuminates.
The preset dryness setting is Normal when a Sensor Dry Cycle is selected. You can select a
different dryness level, depending on your load, by pressing Dryness and choosing More,
Normal, Less or Damp. Selecting More, Normal, Less or Damp automatically adjusts the
dryness level at which the dryer will shut off. Once a dryness level is set, it cannot be changed
without stopping the cycle.
Mot
NOrMAU
ESS
DRYNESS
SENSOR DRY
on,Y
NOTE: I)ryness Level selections cannot be used with the Timed Cycles.
Timed Cycle Modifiers
Use the TEMPERATURE button to select temperatures for the Timed Cycles. Press TEMP until
the desired temperature setting illuminates.
TEMP
ADJUST TIMED
CYCES
NOTE: Temperature modifiers cannot be used with the Sensor I)ry Cycles.
Air Fluff
Use the Air Fluff Modifier for items that require drying without heat such as rubbeb plastic
and heat-sensitive fabrics. This table shows examples of items that can be dried using Air
Fluff.
Type of Load Time* (Minutes)
Foam rubber - pillows, padded bras, stuffed toys 20 - 30
Plastic - Shower curtains, tablecloths 20 - 30
Rubber-backed rugs 40 - 50
O[efin, po[ypropy[ene, sheer nylon 10 - 20
*Reset cycle to complete drying, if needed.
When using Air Fluff
Check that coverings are securely stitched.
Shake and fluff pillows by hand periodically during the cycle.
Dry item completely. Foam rubber pillows are slow to dry.
NOTE: Air Fluff is not available with Sensor Dry Cycles.
Youcancustomizeyourcyclesbyselectingoptions.
DRUM
LIGHT
WRINKLE
PREVENT
DAMP DRY
CHIME
OPTIONS
Drum Light
On some models, select Drum I.ight to turn on the light inside the dryer drum. During a cycle,
if Drum I.ight is selected, the drum light turns on and will remain on until DRUM IJGHT is
pressed again, the door is opened and closed, or the door is [eft open for 5 minutes.
When the dryer is not running, the drum light will turn on when DRUM HGHT is pressed or
the dryer door is opened, and it will remain on until the dryer door has been open for
5 minutes, the dryer door is closed or DRUM I.IGHT is pressed again.
Press DRUM I.IGHT at any time to turn the drum light ON or OFF.
Wrinkle Prevent Setting
The Wrinkle Prevent setting helps keep wrinkles from forming when you cannot unload the
dryer promptly at the end of a cycle. During this option, the dryer stops tumbling and then
tumbles again for a brief period.
Press the Wrinkle Prevent setting to get up to 120 minutes of heat-free, periodic tumbling
at the end of a cycle.
Stop the WRINKI.E PREVENT at any time by pressing Wrinkle Prevent setting or opening
the dryer door.
For the Wrinkle Control Cycle, the Wrinkle Prevent setting is preset to ON. The other
Sensor Dry Cycles will retain the Wrinkle Prevent setting. For example, if you select the
Wrinkle Prevent setting in the Normal cycle, the Wrinkle Prevent setting will be on the
next time you select the Normal cycle.
NOTE: If you do not select the Wrinkle Prevent setting, the dryer stops after cool down.
Damp Dry Chime
Select the I)arnp I)ry Chime to alert you that your clothes are approximately 80% dry. This is
useful when you want to remove lightweight items in a mixed load to avoid overdrying or
remove partially dry items that may need ironing.
The Damp Dry Chime is useful when drying bedsheets/linens in a mixed load. When the
signal goes off, open the door to stop the dryec rearrange the load inside the dryec close the
door and restart the dryer to finish the drying cycle. Rearranging the load will aid in the drying
process.
NOTE: The Damp Dry Chime is available only with the Sensor Dry Cycles.
End of Cycle Signal
The End of Cycle Signal produces an audible sound when the drying cycle is finished.
Promptly removing clothes at the end of the cycle reduces wrinkling.
Press END OF CYCI.E SIGNAl. until the desired volume (High, I.ow or Off) is selected.
HIGH
LOW
END OF
CYCLE
SIGNAL
NOTE: When the Wrinkle Prevent setting is selected and the End of Cycle Signal is on, a tone
sounds every 5 minutes until the clothes are removed, or the Wrinkle Prevent setting ends.
" .I I
You can change Sensor Dry and Timed Cycles, Modifiers and Options anytime before
pressing Start.
Three short tones sound if an unavailable combination is selected. The last selection will
not be accepted.
Changing Cycles after pressing Start
1. Press PAUSE/CANCEl. twice.
2. Select the desired cycle and options.
3. Press START. The dryer starts at the beginning of the new cycle.
NOTE: If you do not press Start within 5 minutes of selecting the cycle, the dryer
automatically shuts off.
Changing Modifiers and Options after pressing Start
You can change an Option or Modifier anytime before the selected Option or Modifier
begins.
1. Press PAUSE/CANCEl. once.
2. Select the new Option and/or Modifiers.
3. Press START to continue the cycle.
NOTE: If you happen to press PAUSE/CANCEl. twice, the program clears and your dryer shuts
down. Restart the selection process.
Changing the Preset Dryness Level Settings
If all of your loads on all Sensor Dry cycles are consistently not as dry as you would like, you
may change the preset Dryness I.eve[ settings to increase the dryness. This change will affect
all of your Sensor Dry cycles.
Your Dryness I.eve[ settings can be adjusted to adapt to different installations, environmental
conditions or personal preference. There are 3 drying settings: 1 (factory preset dryness [eve[),
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Maytag MGD6300TQ - Bravos Gas Dryer Mode d'emploi

Catégorie
Sèche-linge électriques
Taper
Mode d'emploi

dans d''autres langues