Wells Manufacturing HDTG-2430G Mode d'emploi

Marque: Wells Manufacturing

Modèle: HDTG-2430G

Catégorie: Plaques électriques

Taper: Mode d'emploi

Ce manuel convient également à

WELLS BLOOMFIELD, LLC

2 ERIK CIRCLE, P. O. Box 280 Verdi, NV 89439

www.wellsbloomfield.com

PRINTED IN CHINA

telephone: 775-689-5703

fax: 775-689-5976

IMPORTANT: DO NOT DISCARD THIS MANUAL

This manual is considered to be part of the appliance and is to be given to the OWNER or

MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of

this appliance. Additional manuals are available from your WELLS DEALER.

THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR

INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any

questions concerning installation, operation or maintenance of this equipment.

OPERATION MANUAL

HEAVY DUTY

GAS GRIDDLE

MODELS

HDTG-2430G

HDTG-3630G

HDTG-4830G

Includes

INSTALLATION

USE & CARE

123

p/n 307735 Rev. (-) ECN-13411 M123 080623 cps

FOR YOUR SAFETY

Do not store gasoline or other flammable liquids

in the vicinity of this or any other appliance.

WARNING:

Improper installation, adjustment, alteration, service or maintenance can cause

property damage, injury or death. Read the installation, operating and mainte-

nance instructions thoroughly before installing or servicing this equipment.

IMPORTANT:

The purchaser of this equipment must post in a prominent location instructions to be followed in the

event the user smells gas. This information shall be obtained by consulting the local gas supplier.

Model HDTG-2430G

ENGLISH

Unless otherwise specified, all commercial cooking

equipment manufactured by WELLS BLOOMFIELD, LLC is

warranted against defects in materials and workmanship for

a period of one year from the date of original installation or

18 months from the date of shipment from our factory,

whichever comes first, and is for the benefit of the original

purchaser only.

THIS WARRANTY IS THE COMPLETE AND ONLY

WARRANTY, EXPRESSED OR IMPLIED IN LAW OR IN

FACT, INCLUDING BUT NOT LIMITED TO, WARRANTIES

OF MERCHANTABILITY OR FITNESS FOR ANY

PARTICULAR PURPOSE, AND/OR FOR DIRECT,

INDIRECT OR CONSEQUENTIAL DAMAGES IN

CONNECTION WITH WELLS BLOOMFIELD PRODUCTS.

This warranty is void if it is determined that, upon inspection

by an authorized service agency, the equipment has been

modified, misused, misapplied, improperly installed, or

damaged in transit or by fire, flood or act of God. It also

does not apply if the serial nameplate has been removed, or

if service is performed by unauthorized personnel. The

prices charged by Wells Bloomfield for its products are

based upon the limitations in this warranty. Seller’s

obligation under this warranty is limited to the repair of

defects without charge by a Wells Bloomfield factory

authorized service agency or one of its sub-service

agencies. This service will be provided on customer’s

premises for non-portable models. Portable models (a

device with a cord and plug) must be taken or shipped to

the closest authorized service agency, transportation

charges prepaid, for service. In addition to restrictions

contained in this warranty, specific limitations are shown in

the Service Policy and Procedure Guide. Wells Bloomfield

authorized service agencies are located in principal cities.

This warranty is valid in the United States and Canada and

void elsewhere. Please consult your classified telephone

directory, your foodservice equipment dealer or contact:

Service Department, Wells Bloomfield, LLC

P.O. Box 280, Verdi, Nevada 89439

phone (775) 689-5707 or fax (775) 689-5976

for information and other details concerning warranty.

LIMITED WARRANTY STATEMENT

SERVICE POLICY AND PROCEDURE GUIDE and ADDITIONAL WARRANTY EXCLUSIONS

NOTE: For your protection, please note that equipment in

this shipment was carefully inspected and packaged by

skilled personnel before leaving the factory. Upon

acceptance of this shipment, the transportation company

assumes full responsibility for its safe delivery.

IF SHIPMENT ARRIVES DAMAGED:

1. VISIBLE LOSS OR DAMAGE: Be certain that any

visible loss or damage is noted on the freight bill or

express receipt, and that the note of loss or damage is

signed by the delivery person.

2. FILE CLAIM FOR DAMAGE IMMEDIATELY:

Regardless of the extent of the damage.

3. CONCEALED LOSS OR DAMAGE: if damage is

unnoticed until the merchandise is unpacked, notify the

transportation company or carrier immediately, and file

“CONCEALED DAMAGE” claim with them. This

should be done within fifteen (15) days from the date

the delivery was made to you. Be sure to retain the

container for inspection.

Wells Bloomfield cannot assume liability for damage or loss

incurred in transit. We will, however, at your request, supply

you with the necessary documents to support your claim.

SHIPPING DAMAGE CLAIM PROCEDURE

1. Resetting of safety thermostats, circuit breakers, over

load protectors, and/or fuse replacements are not

covered by this warranty unless warranted conditions

are the cause.

2. All problems due to operation at voltages or phase

other than specified on equipment nameplates are

not covered by this warranty.

Conversion to correct voltage and/or phase must be

the customer’s responsibility.

3. All problems due to electrical connections not made

in accordance with electrical code requirements

and wiring diagrams supplied with the equipment are

not covered by this warranty.

4. Replacement of items subject to normal wear, to

include such items as knobs, light bulbs; and, normal

maintenance functions including adjustments of

thermostats, adjustment of micro switches and

replacement of fuses and indicating lights are not

covered by warranty.

5. Damage to electrical cords and/or plug due to exposure

to excessive heat are not covered by this warranty.

6. Full use, care, and maintenance instructions supplied

with each machine. Noted maintenance and

preventative maintenance items, such as servicing and

cleaning schedules, are customer responsibility. Those

miscellaneous adjustments noted are customer

responsibility. Proper attention to preventative

maintenance and scheduled maintenance procedures

will prolong the life of the appliance.

7. Travel mileage is limited to sixty (60) miles from an

Authorized Service Agency or one of its sub-service

agencies.

8. All labor shall be performed during regular working

hours. Overtime premium will be charged to the buyer.

9. All genuine Wells replacement parts are warranted for

ninety (90) days from date of purchase on non-

warranty equipment. This parts warranty is limited only

to replacement of the defective part(s). Any use of

non-genuine Wells parts completely voids any

warranty.

10. Installation, labor, and job check-outs are not

considered warranty and are thus not covered by this

warranty.

11. Charges incurred by delays, waiting time or operating

restrictions that hinder the service technician’s ability to

perform service are not covered by warranty. This

includes institutional and correctional facilities.

123 307735 OpManual for HDTG-Series Griddles

ENGLISH

WARRANTY xi

SPECIFICATIONS 1

FEATURES & OPERATING CONTROLS 2

PRECAUTIONS & GENERAL INFORMATION 3

AGENCY LISTING INFORMATION 3

INSTALLATION 4

OPERATION 8

CLEANING INSTRUCTIONS 10

TROUBLESHOOTING SUGGESTIONS 12

PARTS & SERVICE 13

CUSTOMER SERVICE DATA 13

FRANÇAIS

DESCRIPTION ET AVERTISSEMENTS DE SÛRETÉ 14

SPÉCIFICATIONS 15

FONCTIONNALITÉS ET COMMANDES 16

PRÉCAUTIONS & RENSEIGNEMENTS D’ORDRE

GÉNÉRAL 17

INFORMATIONS CONCERNANT LES AGENCES 17

INSTALLATION 18

FONCTIONNEMENT 22

INSTRUCTIONS POUR LE NETTOYAGE 24

CONSEILS POUR LE DÉPANNAGE 26

Thank You for purchasing this Wells Bloomfield appliance.

Proper installation, professional operation and consistent maintenance of this appliance will ensure that it

gives you the very best performance and a long, economical service life.

This manual contains the information needed to properly install this appliance, and to use and care for the

appliance in a manner which will ensure its optimum performance.

TABLE OF CONTENTS

SPECIFICATIONS

INTRODUCTION

MODEL STYLE FUEL

MANIFOLD

PRESSURE

B.T.U.

per HOUR

HDTG-2430G

2 Dual Burners w/

Individual Control

Natural Gas 5.0” W.C.

60,000

Propane (LP) 10” W.C.

HDTG-3630G

3 Dual Burners w/

Individual Control

Natural Gas 5.0” W.C.

90,000

Propane (LP) 10” W.C.

HDTG-4830G

4 Dual Burners w/

Individual Control

Natural Gas 5.0” W.C.

120,000

Propane (LP) 10” W.C.

123 307735 OpManual for HDTG-Series Griddles

ENGLISH

FEATURES & OPERATING CONTROLS

Fig. 1 HDTG Heavy Duty Gas Griddle - Features & Operating Controls

ADJUSTABLE

LEG

GREASE TRAY

CONTROL

VALVE

COOKING SURFACE

GREASE

TROUGH

GREASE

CHUTE

OPENING

INTERIOR

COMPONENTS

BURNER ASSEMBLIES

PILOT

LIGHTS

THERMOSTATIC

CONTROL VALVE

(typical)

PILOT ADJUST

EXHAUST GAS FLUE

THERMOBULB

ASSEMBLIES

123 307735 OpManual for HDTG-Series Griddles

ENGLISH

This appliance is intended for use in commercial establishments

only.

This appliance is intended

to prepare food for human consumption.

No other use is

recommended or authorized by the manufacturer or its

agents.

This appliance must be installed by a technician qualified and certified

or licensed to install gas-fired equipment. A licensed technician must

perform the initial start-up and adjustment of the appliance.

Operators of this appliance must be familiar with the appliance use,

limitations and associated restrictions. Operating instructions must be

read and understood by all persons using or installing this appliance.

Cleanliness of this appliance is essential to good sanitation. Read and

follow all included cleaning instructions and schedules to ensure the

safety of the food product.

DO NOT submerge appliance or burners in water. This appliance is

not jet stream approved. DO NOT direct water jet or steam jet at this

appliance, or at any control. DO NOT splash or pour water on, in or

over any controls. DO NOT wash counter around this appliance with

water jet. Burners which have become wet must be thoroughly dried

before use.

Griddle surface will be very hot when in use. Contact will cause severe

injury.

This appliance must be operated with the supplied 4” legs properly

installed.

Do not operate this appliance if the smell of gas is present. Turn off

all gas supply valves and move to a remote location to call your

Authorized Wells Service Agent for service.

The technical content of this manual, including any parts breakdown

illustrations and/or adjustment procedures, is intended for use by

qualified technical personnel only.

Any procedure which requires the use of tools must be performed by a

qualified technician.

This manual is considered to be a permanent part of the appliance.

This manual and all supplied instructions, diagrams, schematics, parts

breakdown illustrations, notices and labels must remain with the

appliance if it is sold or moved to another location.

This appliance conforms to NSF Standard 4 for sanitation only if

installed in accordance with the supplied Installation Instructions and

maintained according to the instructions in this manual.

This appliance meets ANSI Z.83.11 specifications for gas-fired food

service equipment.

This appliance is Canadian Standards Association design certified for

gas operation

WARNING:

FIRE HAZARD

All servicing of the gas

supply and combustion

components of this appliance

must be performed by a

technician trained and

certified in the maintenance

of gas appliances.

Improper servicing of gas

equipment can result in fire

and explosion.

CAUTION:

HOT SURFACE

Exposed surfaces can be hot

to the touch and may cause

burns.

STD 4

AGENCY LISTING INFORMATION

PRECAUTIONS AND GENERAL INFORMATION

123 307735 OpManual for HDTG-Series Griddles

ENGLISH

INSTALLATION

NOTE: DO NOT discard

the carton or other packing

materials until you have

inspected the appliance for

hidden damage and tested it

for proper operation.

Refer to SHIPPING DAMAGE

CLAIM PROCEDURE on the

inside front cover of this

manual.

DANGER:

HEALTH

HAZARD

This appliance must be

properly ventilated. Failure to

provide and maintain proper

ventilation of exhaust gasses

can result in severe injury or

death.

WARNING:

FIRE HAZARD

Do not store gasoline or

any other flammable or

combustible material near this

appliance. The open flame

can cause such materials to

ignite.

The area where the griddle is

installed must be kept clear of

combustibles and flammables.

This includes mops, rags,

grease, wrapping paper and

electric cords.

NOTICE: Manufacturer’s

warranty on this griddle is in

effect only when the griddle is

installed in accordance with

these instructions and local

codes and ordinances or, in

the absence of local codes,

the National Fuel Gas Code,

ANSI Z223.1 (current edition).

The manufacturer of this

griddle assumes no liability for

any damage or injury resulting

from failure to comply with this

notice.

UNPACKING & INSPECTION

Carefully remove the appliance from the carton. Remove all

protective plastic film, packing materials and accessories from the

appliance before connecting performing any installation procedure.

Carefully read all instructions in this manual and the Installation

Instruction Sheet packed with the appliance before starting any

installation.

Read and understand all labels and diagrams attached to the

appliance.

Carefully account for all components and accessories before

discarding packing materials. Store all accessories in a convenient

place for later use.

COMPONENTS

Dual Burner (-2430G, 2 ea.; -3630G, 3 ea.; -4830H, 4 ea.)

Adjustable Legs (set of 4)

Grease Tray (-2430G, 1 ea.; -3630G, 1 ea.; -4830H, 2 ea.)

SETUP

Setup the griddle only on a firm, level, non-combustible surface.

Verify local codes for requirements. Concrete, tile, terrazzo or metal

surfaces are recommended. Metal or tile over combustible material

may not meet code for non-combustible surfaces.

Install the provided adjustable

legs, one on each corner of the

appliance, in the holes provided.

Verify that the unit sits firmly ON

ALL FOUR LEGS. With the

adjustable legs, adjust as

required to level the appliance.

All four legs must be adjusted to

firmly contact the countertop in

order to prevent tipping.

Adequate clearance for air openings in the cabinet must be provided.

Refer to the Installation Instruction Sheet for required clearances.

Maintain required clearances between the appliance and adjacent

combustible surfaces.

The griddle must be installed in an area with sufficient make-up air

for proper combustion, and must be installed such that the flow of

combustion and ventilation air will not be obstructed.

When used with an exhaust fan, special precautions must be

observed to avoid interference with the operation of the griddle, such

as drafts and air starvation.

123 307735 OpManual for HDTG-Series Griddles

ENGLISH

GAS APPLIANCE CODE COMPLIANCE

The installation of gas piping from the outlet side of the gas meter or

service regulator to the griddle must be performed by a technician

qualified and certified or licensed to install gas-fired equipment.

A licensed and qualified technician must perform the initial startup and

adjustment of this appliance.

The installation of this gas-fired appliance must conform to local codes,

or in the absence of such codes, with the current edition of

National Fuel Gas Code ANSI Z223.1.

For use in the State of Massachusetts, this appliance must be installed

in compliance with Massachusetts Fuel Gas and Plumbing Code

CMR 248.

The installation of this gas-fired appliance must comply with

applicable portions of NFPA 96 for ventilation. The current edition of

NFPA 96 (Standard for the Installation of Equipment for the Removal

of Smoke and Grease Laden Vapors from Commercial Cooking

Equipment) specifies ventilation requirements to ensure the removal

of exhaust gasses and products of combustion.

IT IS THE RESPONSIBILITY OF THE INSTALLER TO ENSURE

THAT THIS GAS GRIDDLE INSTALLATION CONFORMS TO ALL

APPLICABLE CODES AND ORDINANCES.

The venting of this appliance must not be obstructed, nor may such

venting interfere with the flow of combustion air required for proper

operation of the gas burners.

Additionally:

1. The gas supply line used to connect the griddle to the gas

supply system must be black iron pipe, or other material as

approved by local ordinance for gas piping.

2. Gas supply piping must be inside 3/4” diameter or greater.

3. Use pipe sealant made specifically for gas piping on all pipe joints.

Apply sealant sparingly to the male threads only

Sealant must be resistant to the action of LP gas.

4. Verify that all supply piping is clean and free of obstructions, dirt,

chips and pipe sealant compound prior to installation.

5. All pipe joints must be checked for leaks before lighting. Leak

checks should be performed with a soap and water solution.

NEVER CHECK FOR LEAKS WITH AN OPEN FLAME.

INSTALLATION (continued)

DANGER:

FIRE AND

EXPLOSION

HAZARD

NEVER use an open flame to

check for gas leaks. Fire and

explosion may result.

WARNING:

RISK OF INJURY

Installation procedures must

be performed by a qualified

technician with full knowledge

of all applicable gas-fired

appliance codes. Failure can

result in personal injury and

property damage.

IMPORTANT:

All pipe joints must be

checked for leaks before

lighting. Leak checks should

be performed with a soap and

water solution.

IMPORTANT:

Information on the

construction and installation

of ventilating hoods may be

obtained from the current

edition of NFPA 96

Standard for the Installation

of Equipment for the Removal

of Smoke and Grease Laden

Vapors from Commercial

Cooking Equipment.

Copies of this standard are

available from the

Nation Fire Protection Assn.:

NFPA

1 Batterymarch Park

P.O. Box 9101

Quincy, MA 02269-9101

123 307735 OpManual for HDTG-Series Griddles

ENGLISH

INSTALLATION (continued)

INSTALLING THE GAS GRIDDLE

Refer to the nameplate. Verify the fuel type and pressure, which must

match the nameplate specifications. Connecting the hotplate to the

wrong fuel type and/or pressure will compromise the safety and/or

performance of the appliance.

BE SURE TO MAINTAIN REQUIRED CLEARANCES TO

COMBUSTIBLE SURFACES.

The griddle must be placed in its final operational position and leveled

front-to-back and side-to-side, with a spirit level, prior to beginning the

gas piping installation. Re-check the level of the unit at the conclusion

of the gas piping installation.

Each gas griddle is supplied with a separate gas pressure regulator,

which must be installed on the manifold pipe protruding from the rear

of the griddle. Ensure that the regulator is installed such that the flow

arrow stamped on the body of the regulator points toward the griddle.

Failure to properly install the supplied regulator will result in an ex-

tremely hazardous condition.

A moisture trap (drip leg) consisting of a tee, 4” nipple pointing down,

and cap must be installed upstream of the gas pressure regulator.

A manual gas shut-off valve may be required by local codes and is,

in any case, strongly recommended. The shut-off valve must be

installed between the gas supply piping and the gas pressure

regulator.

It is the responsibility of the gas piping installer to identify the code

requirement for a shut-off valve.

Shut-off valves, moisture trap and all associated piping must be

supplied by the gas piping installer.

DANGER:

FIRE AND

EXPLOSION

HAZARD

NEVER use an open flame to

check for gas leaks. Fire and

explosion may result.

IMPORTANT:

All pipe joints must be checked

for leaks before lighting. Leak

checks should be performed

with a soap and water solution.

WARNING:

FIRE HAZARD

This griddle is supplied with a

gas pressure regulator.

Failure to properly install the

supplied regulator will result in

an extremely hazardous

condition.

Flow arrow stamped on body

of regulator must point toward

the griddle.

Vent hole must point UP.

IMPORTANT:

Verify fuel gas type. If the

available fuel does not match

the nameplate specification,

exchange the hotplate for the

correct type.

IMPORTANT:

The appliance and its

individual manual shutoff valve

must be disconnected from

supply system piping during

any pressure testing of that

system at pressures in excess

of 1/2 p.s.i. (3.5 kPa).

Also, the appliance must be

isolated from the gas supply

piping system by closing its

individual manual shutoff valve

during any pressure testing of

the gas supply piping at test

pressures equal to or less than

1/2 p.s.i. (3.5 kPa).

Fig. 2 Gas Supply Piping

FLOW

DRIP LEG*

GAS

SHUT-OFF

VALVE*

SUPPLIED

REGULATOR

* by others

BACK OF GRIDDLE

GAS

SUPPLY*

VENT

123 307735 OpManual for HDTG-Series Griddles

ENGLISH

INSTALLATION (continued)

SET GAS PRESSURE:

Gas pressure regulator is factory set.

SET PILOT FLAME:

Remove all burner control knobs, then remove the front panel.

The pilot adjustments are near the control valve for each set of

burners.

Using a small, flat-blade screwdriver, turn the screw clockwise to

decrease the flame size, or counter-clockwise to increase the

flame size.

Adjust the pilot flame to 1/4” high. Test for operation: all sections

of the burner must light without undue delay. Drafty conditions

may require a higher flame to allow the pilot to remain lit.

Replace the front panel and all knobs before returning the unit to

service.

ADJUST BURNER FLAME:

Remove all burner control knobs, then remove the front panel.

Turn an individual burner on.

Loosen the locking screw on the shutter.

Turn the shutter to admit more or less air as required. Adjust the

air shutter until the flame is mostly blue in color.

Tighten the locking screw when finished. Replace the front panel

and all knobs before returning the unit to service.

Fig. 3 Flame Adjustments

IMPORTANT:

Adjustments must be performed

by a qualified technician only.

IMPORTANT:

The griddle is shipped from

the factory equipped for natural

gas and adjusted for sea level

to 2000 feet elevation.

For conversion to LP / Propane,

or for operation above 2000 feet

elevation, contact your

Authorized Wells Service

Agency.

LESS

FLAME

MORE AIR

LOCKING

SCREW

LESS

AIR

SHUTTER

PILOT

FLAME

ADJUST

BURNER

FLAME

ADJUST

BURNER

CONTROL

KNOB

PILOT

FLAME

ADJUST

123 307735 OpManual for HDTG-Series Griddles

ENGLISH

OPERATION

GENERAL OPERATIONAL NOTES

Carefully read the description of the griddle operation on the

specification sheet.

Do NOT use this appliance if it has been submerged in water.

Call a qualified technician to examine the appliance and to service

or replace any component which has been submerged. Burners

which have been allowed to become wet must be thoroughly dried

before use.

For initial startup, and any time the gas supply has been shut-off, it

may take several minutes to light the pilot while air in the piping and

manifolds is purged.

The burner control knobs must be turned by hand only. Never use

tools to turn the control knob. If the knob will not turn by hand, DO

NOT attempt to force or repair it. Contact your Authorized Wells

Service Agency for repairs. Forced or improperly repaired valves

pose the risk of fire and/or explosion.

Make sure burners, pilot burner and grease tray are properly installed

before attempting to operate.

LIGHTING THE PILOT FLAME

Before lighting the pilot light, smell all around the appliance area for

gas. Be sure to smell near floor level because some gas is heavier

than air and will settle to the floor.

For initial startup, and any time the gas supply has been shut-off, it

may take several minutes to light the pilot while air in the piping and

manifolds is purged.

The pilot light must be lighted by hand:

Turn all control knobs to the full OFF position.

The pilot is located adjacent to one leg of the burner, and is

accessible through the front panel opening.

Be sure the gas shut-off valve is ON and the appliance has had

time for the air to be purged from the lines. Attempt to light the

pilot every 15 seconds after the gas valve is turned on.

Light the pilot with a long match or fireplace lighter.

DO NOT use a cigarette lighter.

SHUT DOWN INSTRUCTIONS

Turn all burner knobs to OFF.

Turn all pilots OFF.

Turn the main gas supply OFF.

WARNING:

FIRE HAZARD

IF YOU SMELL GAS:

¤ DO NOT try to light

any appliance.

¤ DO NOT touch any

electrical switch

¤ DO NOT use any

telephone in your

building.

In the event a gas odor is

detected, shut down the

unit at the main gas shut-

off valve and contact your

local gas supplier from a

neighboring location.

Follow the instructions

received from the gas

supplier immediately

and exactly.

123 307735 OpManual for HDTG-Series Griddles

ENGLISH

WARNING:

FIRE HAZARD

NEVER attempt to force or

repair a stuck control valve.

Contact your Authorized Wells

Service Agency for repairs.

Forced or improperly repaired

valves pose the risk of fire and/

or explosion.

WARNING:

FIRE AND

EXPLOSION

HAZARD

If the pilot light should be

extinguished, turn off the gas

shut-off valve. Allow the

appliance to vent for five

minutes before attempting to

re-light.

CAUTION:

HOT SURFACE

Exposed surfaces can be hot

to the touch and may cause

burns.

OPERATION (continued)

SEASON THE GRIDDLE SURFACE

As manufactured, the steel surface of your Wells griddle has

microscopic pores. It is important to fill these pores with oil in order to

provide a hard, non-stick cooking surface.

a. Preheat the griddle surface to 375ºF (191ºC).

b. Spread a light film of cooking oil over the entire griddle surface

c. Allow the oil film to cook in for approximately 2 minutes, or until

it smokes.

d. Wipe the griddle surface with a clean damp cloth until all oil is

removed.

e. For new griddles, repeat this procedure 2-3 times until the

griddle has a slick, clean surface.

OPERATION

Inspect the unit for cleanliness before use. Clean as necessary: See

Cleaning Instructions, page 10.

Be sure the pilot light is lit before operation. See Lighting the Pilot

Light, page 8.

The burner control knobs must be turned by hand only. Never use

tools to turn the control knob.

The control used in this gas griddle provides a continuous range of

settings from approximately 200ºF (93ºC) to 450ºF (230ºC).

Light the burner by turning the control knob to the highest setting until

fire forms completely in all sections of the burner. Set the control knob

to the desired temperature. The setting can be readjusted at any time.

Turn knob folly colckwise to turn burner off.

Cooking Recommendations:

Save energy by turning the temperature control knob OFF any time the

griddle is not in use. Gas burners provide full heat instantly, making it

unnecessary to leave the unit on during intermittent use.

Fig. 4 Burner Control

200

300

350

250

400

450

OFF POSITION SET TO 350ºF≈

123 307735 OpManual for HDTG-Series Griddles

ENGLISH

CLEANING INSTRUCTIONS

PREPARATION

Turn control valve to a low setting before cleaning.

Allow griddle to cool to this lower setting before cleaning.

FREQUENCY

Daily

TOOLS

Bristle Brush

Clean Cloth or Sponge

Mild Detergent

Cleaner Formulated for Stainless Steel

Warm Water

DAILY CLEANING

1. Pour a small amount of water on the griddle surface and let it

"sizzle".

2. Clean the griddle surface. Use a pumice stone or griddle brick to

scrape food waste. Clean the griddle surface down to bright metal.

Wipe off any remaining powder residue.

IMPORTANT: NEVER USE STEEL WOOL TO CLEAN THE

GRIDDLE SURFACE!

DO NOT use detergent or oven cleaner to clean the griddle surface.

3. Use a soft-bristled fiber brush in a circular motion to remove any

remaining food particles.

4. Turn temperature control to OFF. Allow the griddle surface to cool,

then wipe the surface with a clean cloth. Dry the griddle surface

thoroughly.

IMPORTANT: SEASON THE COOKING SURFACE AFTER EACH

CLEANING. See page 9.

5. At least once each day, the grease trough must be thoroughly

cleaned. Using a scraper, remove all grease and food waste from

the grease trough by pushing it down the waste hole and into the

grease tray.

6. After scraping all cooking waste from grease trough into the grease

tray, take the grease drawer to the kitchen cleaning area and

properly dispose of all waste.

a. Clean drawer with hot water and a mild detergent.

b. Dry drawer thoroughly and reinstall in griddle.

7. Wipe down exterior of griddle cabinet with a clean cloth and non-

abrasive cleanser. Rinse thoroughly with water and a clean cloth.

Dry with a soft clean cloth.

Procedure is complete.

WARNING:

FIRE HAZARD

Shut off the gas supply

valve before cleaning.

CAUTION:

BURN HAZARD

Allow hotplate to cool

completely before

cleaning.

IMPORTANT: DO NOT spill

or pour water into controls.

DO NOT submerge griddle

cabinet in water. Damage to

internal components will

occur.

Damage to internal

components from water

damage is NOT covered by

warranty.

DO NOT steel wool or

metal scouring pads to clean

cabinet or grease tray.

Good sanitation is vital to the

quality of the final food

product. Be sure to clean in

all corners and crevices

where grease and other

cooking debris can

accumulate.

123 307735 OpManual for HDTG-Series Griddles

ENGLISH

PREPARATION

Turn gas shut-off valve OFF.

Allow griddle to cool before cleaning.

FREQUENCY

As Needed

TOOLS

Bristle Brush

Clean Cloth or Sponge

Mild Detergent

Cleaner Formulated for Stainless Steel

Warm Water

CLEANING BURNERS

If one or more individual flame openings does not light, or if the flame

is intermittent or uneven, the burner may need to be cleaned.

Turn shut-off valve OFF. Remove all control knobs and remove front

panel.

Note position of burner assemblies in cabinet. Remove burners.

Examine burner assemblies. Note position of air shutters before

cleaning. Clean food particles from burners with warm water, mild

detergent and a bristle brush. Rinse by wiping with a soft cloth

dampened with clean water. Wipe exterior surfaces dry with a soft

clean cloth. Allow burners to air dry so that interior passages are

completely free of water.

Examine burners to be sure the air shutters are in their proper position.

Reinstall burners with flame openings “up”. The venturi / air shutter

slides over the nozzle of the control valve. The pegs on the rear of the

burner set in corresponding notches in the rear burner support bracket.

The pegs on the front of the burner set on the front support bracket.

Turn shut-off valve ON and light pilot light.

Reinstall front panel and all control knobs.

Test all burners for proper operation.

Procedure is complete.

CLEANING INSTRUCTIONS (continued)

WARNING:

FIRE HAZARD

Shut off the gas supply

valve before cleaning.

IMPORTANT: DO NOT spill

or pour water into burners or

controls,

DO NOT submerge griddle

cabinet in water. Damage to

internal components will

occur.

Damage to internal

components from water

damage is NOT covered by

warranty.

123 307735 OpManual for HDTG-Series Griddles

ENGLISH

TROUBLESHOOTING

SYMPTOM POSSIBLE CAUSE SUGGESTED REMEDY

Pilot will not light

Gas supply off Check main / unit gas valves

Air in lines

Turn pilot valve on. Attempt to

light pilot every 15 sec.

Pilot valve not on Turn pilot valve on / adjust

Burners won’t light

Gas supply off Check main / unit gas valves

Air in lines

Turn gas valve on. Attempt to

light pilot every 15 sec.

Pilot burner not lit

Turn off gas - allow unit to

vent for 5 minutes. Turn gas

back on and light pilot

Control not set high enough

Turn control knob to desired

temperature

Set to desired setting when lit

Water in burner

Remove burner and dry

thoroughly

Damaged temperature control,

burner or other internal

component

Contact Authorized Wells

Service Agency for repairs

Portions of a burner won’t light

or have erratic flame

Burner wet or flame opening(s)

clogged

Clean and dry burner

Burner not hot enough

Temperature control not set Adjust for desired temperature

Shutter or nozzle out of

adjustment

Contact qualified technician for

adjustment

Damaged temperature control,

burner or other internal

component

Contact Authorized Wells

Service Agency for repairs

NOTE: There are no user

serviceable components in the

burner assemblies or in the

control valves. In all cases of

damage or malfunction,

contact your Authorized Wells

Service Agency for repairs.

One burner assembly

won’t light

123 307735 OpManual for HDTG-Series Griddles

CUSTOMER SERVICE DATA

please have this information available if calling for service

RESTAURANT _____________________________ LOCATION _____________

INSTALLATION DATE ________________________ TECHNICIAN ___________

SERVICE COMPANY ________________________________________________

ADDRESS ___________________________ STATE ______ ZIP__________

TELEPHONE NUMBER (_____)_____-_________

EQUIPMENT MODEL NO. _______________

EQUIPMENT SERIAL NO. _______________

FUEL (check one) NATURAL GAS PROPANE / LP

ENGLISH

DESCRIPTION PART NO.

LEGS, ADJUSTABLE 4” METAL (SET of 4) 20563

PARTS & SERVICE

IMPORTANT: Use only

factory authorized service

parts .

For factory authorized

service, or to order factory

authorized replacement parts,

contact your Wells authorized

service agency, or call:

Wells Bloomfield, LLC

2 Erik Circle

P. O. Box 280

Verdi, NV 89439

Service Parts Dept.

phone: (775) 689-5707

fax: (775) 689-5976

Service Parts Department can

supply you with the name and

telephone number of the

WELLS AUTHORIZED

SERVICE AGENCY

nearest you.

123 307735 OpManual for HDTG-Series Griddles

FRANÇAIS

MANUEL DE L’UTILISATEUR

WELLS GRILL PROFESSIONNEL

MODÈLES

HDTG-2430G

HDTG-3630G

HDTG-4830G

Comprend :

INSTALLATION,

MODE D’EMPLOI

& ENTRETIEN

POUR VOTRE SÉCURITÉ

Ne pas stocker d’essence ou d'autres liquides inflammables au voisinage de cet

appareil ou autres appareils ménagers.

AVERTISSEMENT !

L’installation, le réglage, les modifications, l’entretien ou la maintenance effectués

de manière incorrecte peuvent entraîner des dommages matériels, corporels ou même

la mort. Lire attentivement les instructions relatives à l’installation, au fonctionnement,

à l’entretien et à la maintenance avant d’installer ou de réparer l’équipement.

IMPORTANT :

L’acquéreur de ce matériel doit afficher, en pleine vue du public, les instructions à

suivre en cas de détection d’une odeur de gaz par l’utilisateur. Cette information

doit être obtenue après consultation de la société locale distributrice du gaz.

IMPORTANT : NE PAS JETER CE GUIDE

Ce guide fait partie de l’appareil et doit être remis au propriétaire, au directeur du

restaurant ou à la personne responsable de la formation des utilisateurs de l’appareil.

Des guides supplémentaires sont disponibles chez votre distributeur Wells.

Ce guide doit être lu et compris par toutes personnes installant ou utilisant cet appareil.

Contacter votre distributeur Wells pour toutes questions au sujet de l’installation, du

fonctionnement ou de l’entretien de cet appareil.

Modéle HDG-3630G

123 307735 OpManual for HDTG-Series Griddles

FRANÇAIS

TABLE DES MATIÈRES

FRANÇAIS

DESCRIPTION ET AVERTISSEMENTS DE SÛRETÉ 14

SPÉCIFICATIONS 15

FONCTIONNALITÉS ET COMMANDES 16

PRÉCAUTIONS & RENSEIGNEMENTS D’ORDRE

GÉNÉRAL 17

INFORMATIONS CONCERNANT LES AGENCES 17

INSTALLATION 18

FONCTIONNEMENT 22

INSTRUCTIONS POUR LE NETTOYAGE 24

CONSEILS POUR LE DÉPANNAGE 26

Merci d’avoir acquis cet appareil Wells Bloomfield. L’installation correcte, le fonctionnement professionnel

et l’entretien régulier de cet appareil assureront ses meilleures performances et sa longue durée de

service aux meilleurs coûts. Le présent manuel contient l’information nécessaire pour installer

correctement l’appareil et pour l’utiliser et l’entretenir de manière à ce qu’il fonctionne avec des

performances optimales.

INTRODUCTION

SPÉCIFICATIONS

MODÈLE STYLE COMBUSTIBLE

PRESSION DU

COLLECTEUR

CONSOMMATION

D’ÉNERGIE

TOTALE (BTU) par

heure

HDTG-1230G

2 brûleurs avec

commandes

individuelles

Gaz naturel 5.0” W.C. 53,000

Propane* 10” W.C.

HDTG-2430G

4 brûleurs avec

commandes

individuelles

Gaz naturel 5.0” W.C. 106,000

Propane* 10” W.C.

HDTG-3630G

6 brûleurs avec

commandes

individuelles

Gaz naturel 5.0” W.C. 159,000

Propane* 10” W.C.

43,000

86,000

129,000

*Propane (gaz de pétrole liquide--GPL)

123 307735 OpManual for HDTG-Series Griddles

FRANÇAIS

FONCTIONNALITÉS ET COMMANDES

Fig. 5 FONCTIONNALITÉS ET COMMANDES DU GRILL PROFESSIONNEL À GAZ

INTERIOR

COMPONENTS

LES TEMPÉRATURE

SENTANTS DES

AMPOULES

PIEDS

RÉGLABLES

BAC POUR

LA GRAISSE

CONTROLER

LE BOUTON

SURFACE DE

CUISSON

PLATEAU POUR

LA GRAISSE

OUVERTURE DU

CONDUIT D'ÉVACUATION

DE LA GRAISSE

CONDUIT

D'ÉVACUATION

DES GAZ

ENSEMBLES

DE BRÛLEURS

CONTROLER

LA SOUPAPE POUR

LA FLAMME DE BRULEUR

L'AJUSTEMENT DE

FLAMME D'ALLUMAGE

ALLUMAGE

DES

BRÛLEURS

123 307735 OpManual for HDTG-Series Griddles

FRANÇAIS

Cet appareil est prévu exclusivement à l’usage des

établissements commerciaux.

Cet appareil est destiné à la cuisson d’aliments pour la consommation

humaine. Aucun autre usage n’est recommandé ni autorisé par le

fabricant ou ses agents.

Cet appareil doit être installé par un technicien qualifié ou et certifié

ou agréé pour l’installation des équipements fonctionnant au gaz. Un

technicien qualifié et agréé doit assurer la mise en service et le réglage

initiaux de l'appareil.

Les utilisateurs de l’appareil doivent être familiarisés avec l’utilisation

de l’appareil, ses limites et ses restrictions associées. Le mode

d’emploi doit être lu et compris par toutes les personnes installant ou

utilisant cet appareil.

La propreté de cet appareil est essentielle à de bonnes conditions sa-

nitaires. Lire et suivre toutes les instructions relatives au nettoyage et

aux programmes visant à assurer l’innocuité des produits alimentaires.

NE PAS submerger l’appareil ou les brûleurs dans l’eau. Cet appareil

n’est pas approuvé pour supporter les jets d’eau. NE PAS orienter

de jet d’eau ou de vapeur directement sur cet appareil ou de ses

commandes. NE PAS éclabousser ni verser d’eau sur, dans ou par

dessus les commandes. NE PAS laver le comptoir entourant l’appareil

avec un jet d’eau. Les brûleurs mouillés doivent être complètement

séchés avant usage.

Les surfaces de cuisson deviennent très chaudes pendant l’usage.

Leur contact provoquera des brûlures graves.

Cet appareil doit être utilisé avec ses pieds de 10 cm (4 po.) de haut

correctement installés.

Ne pas utiliser cet appareil en présence d’une odeur de gaz. Fermer

tous les robinets à gaz et se rendre dans un lieu éloigné pour appeler

un technicien d’entretien agréé par Wells.

La partie technique du présent manuel, y compris tous les schémas

éclatés illustrant les pièces et/ou les procédures de réglage, est

destinée exclusivement à l’usage de techniciens qualifiés.

Toute procédure exigeant l’emploi d’outils doit être accomplie par un

technicien qualifié.

Le présent manuel est considéré être une pièce permanente de

l’appareil. Ce manuel et toutes les instructions, schémas, illustrations

de pièces éclatées, notices et étiquettes fournis doivent demeurer avec

l’appareil si ce dernier est revendu ou déménagé dans un autre local.

Cet appareil n’est conforme à la Norme 4 de la fondation nationale de

normalisation sanitaire des États-Unis (National Sanitation Foundation-

-NSF) que s’il est installé conformément aux Instructions relatives à

l’installation fournies avec l’appareil et si ce dernier est entretenu selon

les instructions du présent manuel.

Cet appareil est conforme aux spécifications ANSI Z.83.11 pour les

appareils à gaz utilisés dans les établissements préparant des

aliments.

Cet appareil est d’une conception certifiée pour le fonctionnement au

gaz par l’Association canadienne de normalisation (ACN/CSA).

AVERTISSEMENT!

DANGER D’INCENDIE

Toutes les opérations

d’entretien et de réparation

des composants servant à

l’alimentation et à la

combustion du gaz dans cet

appareil doivent être

effectuées par un technicien

qualifié et agréé pour la

maintenance des appareils

à gaz. L’entretien incorrect

des appareils à gaz peut

entraîner des incendies et

des explosions.

ATTENTION:

SURFACE CHAUDE

Les surfaces exposées

peuvent être chaudes au

toucher et peuvent

occasionner des brûlures.

Norme 4

INFORMATIONS CONCERNANT LES AGENCES

PRÉCAUTIONS & RENSEIGNEMENTS D’ORDRE GÉNÉRAL

123 307735 OpManual for HDTG-Series Griddles

FRANÇAIS

L'INSTALLATION

REMARQUE : NE PAS jeter le

carton ni les autres matériaux

d’emballage jusqu’à ce que

l’appareil ait été inspecté pour la

détection de vices cachés et ait

subi des tests de fonctionnement

satisfaisants. Consulter la

PROCÉDURE DE RÉCLAMA-

TION EN CAS DE DOMMAGES

DUS AU TRANSPORT imprimée

sur la face interne de la première

page de couverture du présent

manuel.

DANGER:

Danger pour la

santé

Cet appareil doit être situé dans

un local correctement aéré. Le

défaut d’assurance et de maintien

d’une aération convenable avec

mise à l’évent des gaz de

combustion peut entraîner des

dommages corporels graves ou

même la mort.

AVERTISSEMENT :

Danger d’incendie

Ne pas stocker

d’essence ou d'autres matériaux

combustibles ou

inflammables à proximité de cet

appareil. Toute flamme nue peut

provoquer l’inflammation de ces

matériaux. La zone où le grill est

installé doit être dépourvue de

tout matériau combustible ou

inflammable. Ceux-ci

comprennent, notamment, les

serpillères, les lavettes ou les

chiffons, la graisse, le papier

d’emballage et les cordons

d’alimentation électriques

NOTICE : La garantie du

fabricant concernant cet appareil

entre en vigueur exclusivement si

l’appareil est installé

conformément aux présentes

instructions, aux dispositions de

la réglementation et des codes

locaux, ou en l’absence de codes,

de la norme ANSI Z223.1 (édition

en vigueur) du code national

relatif au gaz combustible

(National Fuel Gas Code). Le

fabricant de ce grill décline toute

responsabilité en cas de

dommages corporels ou matériels

résultant du défaut d'application

des dispositions de la présente

notice.

DÉBALLAGE & INSPECTION

Sortir l’appareil du carton avec précaution. Enlever tous les films de

protection en plastique, les matériaux d’emballage et les accessoires

de l’appareil avant d'entamer toute procédure d'installation et de

connexion.

Lire attentivement toutes les instructions du présent manuel et de la

Notice-–Instructions relatives à l’installation, incluse avec l’appareil,

avant de commencer l’installation.

Lire et assimiler la signification de toutes les étiquettes et schémas

fixés sur l’appareil.

Vérifier que tous les composants et accessoires sont présents avant de

jeter les matériaux d'emballage. Ranger tous les accessoires dans un

lieu convenable pour les utiliser plus tard.

COMPOSANTS

Double brûleur

(-2430G, 2 pièce; -3630G, 3 pièce; -4830H, 4 pièce)

Pieds réglables (jeu de 4)

Plateau pour la graisse

(-2430G, 1 pièce; -3630G, 1 pièce;

-4830H, 2 pièce)

INSTALLATION

Installer l’appareil uniquement sur une surface solide, horizontale et

non combustible. Vérifier les conditions imposées par les codes locaux.

Les surfaces en ciment, en carreaux de céramique ou de marbre, ou

en métal sont recommandées. Le métal ou les carreaux de céramique

posés sur des matériaux combustibles peuvent être incompatibles avec

les dispositions du code imposant des surfaces

non combustibles.

Installer les pieds fournis avec l’appareil,

un pied à chaque coin de l’appareil, dans

les trous préparés. Vérifier que l’unité est

stable et repose bien SUR LES QUATRE

PIEDS. Les pieds étant réglables, les ajuster

selon les besoins pour que l’appareil soit

horizontal. Les quatre pieds doivent être

ajustés pour faire solidement contact avec

le comptoir afin d’éviter tout basculement.

Ménager des dégagements adéquats dans l’armoire pour les orifices

d’aération. Consulter la Notice—Intructions relatives à l’installation,

pour obtenir les dimensions de dégagement obligatoires. Conserver

les distances de dégagement nécessaires entre l’appareil et les

surfaces combustibles adjacentes.

L’appareil doit être installé dans un lieu où l’air est suffisamment

renouvelé pour assurer une combustion correcte et de telle manière

que le courant de l’air de combustion et d’aération ne soit pas obstrué .

Lorsqu’on utilise l’appareil avec un ventilateur d’extraction, il faut

prendre des précautions spéciales pour éviter toute interférence avec

le fonctionnement de l’appareil, tels que courants d’air et privation

d’air .

FIXATION PAR

VIS DANS LE

CADRE

TOURNER

POUR

RÉGLER

LA HAUTEUR

123 307735 OpManual for HDTG-Series Griddles

La page charge ...

Wells Manufacturing HDTG-2430G Mode d'emploi

Marque: Wells Manufacturing

Modèle: HDTG-2430G

Catégorie: Plaques électriques

Taper: Mode d'emploi

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Wells Manufacturing HDTG-2430G Operating instructions

Wells Manufacturing HDTG-2430G Mode d'emploi

Ce manuel convient également à

Wells Manufacturing HDTG-2430G Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents