KitchenAid KSBS25FKBL02 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KSBS25FKBL02

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

Kitchen_kid ®

CABINET DEFFH

SIDE BY SIDE REFRIGERATOR

For questions about features, operation/performance, parts accessories or service, call: 1-800-422-1230

In Canada, call for assistance 1-800-461-5681, for installation and service, call: 1-800-807-6777 or visit our website at...

www.kitchenaid.com or www.KitchenAid.ca

REFRIGERATEUR COTE A COTE A

PROFONDEUR D'AILMOIRE

Au Canada, pour assistance composez le 1-800-461-5681, pour installation ou service composez le 1-800-807-6777 ou visitez notre site web &...

www.KitchenAid.ca

Table of Contents/Table des matieres ............................................................................. 2

2221544

TABLE OF CONTENTS

REFRIGERATOR SAFETY .......................................................... 3

INSTALLATION INSTRUCTIONS .................................................. 4

Unpacking .................................................................................... 4

Location Requirements ................................................................ 4

Electrical Requirements ............................................................... 5

Removing the Door Handles ........................................................ 5

Water System Preparation ........................................................... 5

Water Supply Connection ............................................................ 6

Custom Door Panels .................................................................... 7

Base Grille .................................................................................... 8

Leveling Refrigerator .................................................................... 8

Normal Sounds ............................................................................ 9

REFRIGERATOR USE .................................................................... 9

Ensuring Proper Air Circulation .................................................... 9

Using the Controls ....................................................................... 9

Water and Ice Dispensers .......................................................... 10

Water Filtration System .............................................................. 11

Ice Maker and Storage Bin/Bucket ............................................ 12

REFRIGERATOR FEATURES ...................................................... 13

Refrigerator Shelves ................................................................... 13

Meat Drawer, Crisper and Covers ............................................. 13

Crisper Humidity Control ........................................................... 14

Beverage Drawer ........................................................................ 14

Wine or Can/Bottle Rack ........................................................... 14

Utility Bin .................................................................................... 14

FREEZER FEATURES .................................................................. 14

Freezer Shelf .............................................................................. 14

Freezer Basket ........................................................................... 15

DOOR FEATU RES ........................................................................ 15

Door Rails ................................................................................... 15

Door Bins .................................................................................... 15

REFRIGERATOR CARE ............................................................... 15

Cleaning ...................................................................................... 15

Changing the Light Bulbs ........................................................... 16

Power Interruptions .................................................................... 17

Vacation and Moving Care ......................................................... 17

TROUBLESHOOTING .................................................................. 17

ASSISTANCE OR SERVICE ......................................................... 20

In the U.S.A ................................................................................ 20

In Canada ................................................................................... 21

Accessories ................................................................................ 21

WATER FILTER CERTIFICATIONS ............................................. 21

PERFORMANCE DATA SHEETS ............................................. 22

WARRANTY .............................................................................. 23

TABLE DES MATIERES

SECURIT¢: DU REFRIGERATEUR ........................................... 24

INSTRUCTIONS D'INSTALLATION ............................................. 25

Deballage .................................................................................... 25

Emplacement d'installation ....................................................... 25

Specifications electriques .......................................................... 26

Enlevement des poignees des pores ........................................ 26

Preparation du systeme d'eau ................................................... 26

Raccordement de la canalisation d'eau .................................... 27

Panneaux de porte sur commande ........................................... 28

Grille de la base .......................................................................... 29

Nivellement du refrigerateur ....................................................... 30

Sons normaux ............................................................................ 30

UTILISATION DU REFRIGERATEUR .......................................... 31

Pour s'assurer d'une circulation d'air appropriee ...................... 31

Utilisation des commandes ........................................................ 31

Distributeurs d'eau et de glagons .............................................. 32

Systeme de filtration d'eau ........................................................ 33

Machine a glagons et bac d'entreposage ................................. 34

CARACTC:RISTIQUES DU REFRIGERATEUR ........................... 35

Tablettes du refrigerateur ........................................................... 35

Tiroir a viande, bac a legumes et couvercles ............................ 36

Reglage de I'humidite dans les bacs a legumes ....................... 36

Tiroir a boisson ........................................................................... 37

Porte-cannettes/bouteilles ou casier a vin ................................ 37

Bac utilitaire ................................................................................ 37

CARACTC:RISTIQUES DU CONGELATEUR ............................... 37

Clayette de congelateur ............................................................. 37

Panier du congelateur ................................................................ 38

CARACTI_RISTIQUES DE LA PORTE ......................................... 38

Tringles dans la porte ................................................................. 38

Compartiments dans la porte .................................................... 38

ENTRETIEN DU RI_FRIGI_RATEUR ............................................ 3g

Nettoyage ................................................................................... 39

Remplacement des ampoules d'eclairage ................................ 39

Pannes de courant ..................................................................... 40

Entretien avant les vacances ou Iors d'un demenagement .......40

Dg:PANNAGE ................................................................................. 41

ASSISTANCE OU SERVICE ......................................................... 45

Accessoires ................................................................................ 45

FEUILLES DE DONNC:ES SUR LE PRODUIT .......................... 46

GARANTI E................................................................................. 47

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all

safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or

"WARNING." These words mean:

You can be killed or seriously injured if you don't

immediately follow instructions.

You can be killed or seriously injured ifyou don't

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you

what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic

precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all panels before operating.

• Remove doors from your old refrigerator.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

• Use two or more people to move and install

refrigerator.

• Disconnect power before installing ice maker (on

ice maker kit ready models only).

• Use a sturdy glass when dispensing ice or water

(on some models).

SAVE THESE INSTRUCTIONS

Proper Disposal of

Your Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or

brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." Ifyou are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

Before you throw away your old refrigerator or freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily

climb inside,

INSTALLATION

INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Removing packaging materials

• Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water

and dry.

Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see the "Refrigerator Safety" section.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator

for cleaning or service, be sure to protect the floor.

Always pull the refrigerator straight out when moving it.

Do not wiggle or "walk" the refrigerator when trying to move

it, as floor damage could occur.

Cleaning before use

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions

in the "Refrigerator Care" section.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when re-

moving them to avoid impact from dropping.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion,

or fire.

NOTE: Do not install the refrigerator near an oven, radiator, or

other heat source, nor in a location where the temperature will fall

below 55°F (13°C).

_]_

(34cm}

36"

(91.5 cm) -_b

2 ..................... _ ...................................72"

(182.9 cm)

I III- 12V2" _, ,_ 20_/4" .

21/2 '' .--_ L 9_/4,,

(6.4cm) (23,5cm)

(42cm)

-- 2"

',5.1cm)

1. Minimum fixed wall position.

2. For full-overlay cabinet doors and a trim kit, the

height of the opening must be 72 _ in. (183.2 cm).

3. Recommended locations for electrical and water

connections.

If you are installing the refrigerator to fit flush with the front of

the base cabinets, all shoe molding and baseboards must be

removed from the rear of the refrigerator opening.

The water hookup and electrical hookup must be placed near

the bottom of the refrigerator.

A trim kit is available for those installations where the

refrigerator will not fit flush. See the "Assistance or Service"

section for ordering information.

ElectricalShock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in

death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical

connection:

Recommended grounding method

A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

IMPORTANT: If this product is connected to a

GFCI (Ground Fault Circuit Interrupter) protected outlet, nuisance

tripping of the power supply may occur, resulting in loss of

cooling. Food quality and flavor may be affected. If nuisance

tripping has occurred, and if the condition of the food appears

poor, dispose of it.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator

or Freezer Control depending on the model) to OFF and then

disconnect the refrigerator from the electrical source. When you

are finished, reconnect the refrigerator to the electrical source

and reset the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting.

..... _ _ *,

__%6_._.... _ _

Apply firm pressure with hand on face of trim. Slide top trim up

and bottom trim down away from handle, then lift off of shoulder

screws. Remove handle screws.

Please read before using the water system.

Immediately after installation, follow the steps below to make

sure that the water system is properly cleaned.

1. Open the freezer door and turn off the ice maker by lifting up

the wire shutoff arm as shown.

NOTES:

• If your model has a base grille filter system, make sure the

base grille filter is properly installed and the cap is in the

horizontal position.

• Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system.

Use a sturdy container to depress the water dispenser bar

until the water begins to flow. Flush the water system by

dispensing and discarding 2 to 3 gal. (8 to 12 L) of water.

Cleaning the system will take approximately 6 to 7 minutes

and will help clear air from the line. Additional flushing may be

required in some households.

NOTE: As air is cleared from the system, water may spurt out

of the dispenser.

Open the freezer door and turn on the ice maker by lowering

the wire shutoff arm. Please refer to the "Ice Maker and

Storage Bin/Bucket" section for further instructions on the

operation of your ice maker.

• Allow 24 hours to produce the first batch of ice.

• Discard the first three batches of ice produced.

Read all directions carefully before you begin.

IMPORTANT:

• If you turn the refrigerator on before the water line is

connected, turn the ice maker OFF.

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing

only in areas where household temperatures will remain

above freezing.

Tools required: Flat-blade screwdriver, 7/16in. and 1_ in. open-

end wrenches or two adjustable wrenches, 1/4in. drill bit, hand

drill or electric drill (properly grounded).

NOTE: Your refrigerator dealer has a kit available with a 1/4in.

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or 3/16in.

(4.76 mm) saddle valve which reduces water flow and clogs more

easily.

Cold Water Supply

Connect the ice maker to a cold water line with water pressure

between 30 and 120 psi. If you have questions about your water

pressure, call your utility company.

Connecting to Water Line

Unplug refrigerator or disconnect power.

Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

Find a 1/2in. (12.70 mm) to 11/4in. (3.18 cm) vertical COLD

water pipe near the refrigerator.

NOTE: Horizontal pipe will work, but the following procedure

must be followed: Drill on the top side of the pipe, not the

bottom. This will help keep water away from the drill. This

also keeps normal sediment from collecting in the valve.

4. Route 1/4in. (6.35 mm) copper tubing from the water pipe to

the lower rear corner of the refrigerator location. Be sure both

ends of copper tubing are cut square.

5. Using a grounded drill, drill a 1/4in. (6.35 mm) hole in the cold

water pipe you have selected.

..................... 1

7 ......_............2

!. Cold water pipe 5. Compression sleeve

2. Pipe clamp 6. Shutoff valve

3. Copper tubing 7.Packing nut

4. Compression nut

6. Fasten shutoff valve to cold water pipe with pipe clamp. Be

sure outlet end is solidly in the 1/4in. (6.35 mm) drilled hole in

the water pipe and that washer is under the pipe clamp.

Tighten packing nut. Tighten the pipe clamp screws carefully

and evenly so washer makes a watertight seal. Do not

overtighten or you may crush the copper tubing, especially if

soft (coiled) copper tubing is used. Now you are ready to

connect the copper tubing.

7. Slip compression sleeve and compression nut on copper

tubing as shown in the diagram. Insert the end of the tubing

into the outlet end of the shutoff valve as far as it will go.

Screw the compression nut onto the outlet end with an

adjustable wrench. Do not overtighten.

8. Place the free end of the tubing into a container or sink, and

turn ON main water supply and flush out tubing until water is

clear. Turn OFF the shutoff valve on the water pipe.

Connecting to Refrigerator

1. Remove the shipping tape from the gray, coiled water tubing

on the rear of the refrigerator.

2. Style 1: Thread the provided nut onto the coupling on the end

of the copper tubing. Tighten the nut by hand. Then tighten it

with a wrench two more turns. Do not overtighten.

1 2 3 4 5

1.Line to refrigerator 4. Coupling (purchased)

2. Nut (provided) 5. Ferrule (purchased)

3. Bulb 6.Nut (purchased)

Style 2: Thread the provided nut onto the water valve as

shown.

I/ll

1.Bulb

2. Nut (provided)

NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

3. Turn shutoff valve ON.

4. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

5. Plug in refrigerator or reconnect power.

6. Flush the water system. See the "Water System Preparation"

section.

NOTE: It may take up to 24 hours for your ice maker to begin

producing ice.

Doo

Creating Custom Wood Panels

If you plan to install custom wood decorator panels, you will need

to create the panels yourself or consult your cabinetmaker or

carpenter. See dimensional drawings for wood panel inserts.

Flat panels:

You can create a custom flat panel a maximum of V4in. (6.35 ram)

thick to replace your decorator panels. Flat wood panels less

than V4in. (6.35 ram) thick are not recommended.

Raised panels:

A raised panel design can be created by screwing or gluing wood

panels to V4in. (6.35 ram) backing or by using 3/4in. (19.05 ram)

stock with routed edges. Raised panels should be spaced

2V4in. (5.70 cm) from the back edge of the handle to allow room

for fingers to grasp the handle.

Weight requirements for raised panel inserts:

• Refrigerator door panel should not exceed 28 Ibs

(12.7 kg).

• Freezer door panels should not exceed 21 Ibs (9.5 kg)

combined weight.

Dimensions for custom wood panels:

(318 ram)

18" 18'

I __(318 rnm)

15 3/8"

(39 cm)

67 15i16"

/172 5cm

I 15 38'

(39 cm)

193(32 r'

{485 cm)

_, 18,,

Routing Dimensions for Custom Panels more than

V4in.(6 mm) thick

Handle side detail

2½" /

1/4" (6 mm) m_ax. 1

ha idle mln I

Top, bottom and side trim detail

J[_ (6 mm) max

W'Z

(127 ram)

rain.

panel --

Installing Custom Wood Panels

1. Remove any packing tape.

2. Remove the refrigerator and freezer door trims from the hinge

side of each door by pulling the trim away from the bottom of

the door first,

3. Partially unscrew the two screws that hold the top trim in

place. It is not necessary to completely remove the screws.

Loosen the screws approximately V4in. (6.35 mm) from the

trim to allow the panels to slide freely.

4. Remove the existing door panels, if panels were provided.

5. Slide custom door panels into place.

NOTE: The freezer door panels may require Vsin. (3.18 mm)

cardboard fillers behind the panels to keep them from being

loose in that area.

Replace the hinge side trims by inserting the notched end

under the top trim first.

Tighten the two top trim screws.

1. Side Trims

2. Top Trim Screws

3. Door Panels

4. Filler Panels

Style 1:

To remove the base grille:

1. Open the refrigerator and freezer doors 90°.

2. Remove screws from the base grille using a screwdriver.

NOTE: Do Not Remove Tech Sheet that is fastened behind the

base grille.

To replace the base grille:

1. Open the refrigerator and freezer doors to 90°.

2. Position the base grille in front of the refrigerator and replace

the screws.

Style 2:

To remove the base grille:

1. Open the refrigerator and freezer doors to 90°.

2. Grasp the grille with both hands.

3. Lift up and tilt the top of the grille toward you.

NOTE: Do not remove the Tech Sheet that is fastened behind the

grille.

To replace the base grille:

1. Open the refrigerator and freezer doors to 90°.

2. Place the lower clips in the openings in the metal panel.

3. Roll the grille up toward the refrigerator until it snaps into

place.

Your refrigerator has a front and rear roller at the base of the

product on each side. All four rollers can be adjusted from the

front of the product. If your refrigerator seems unsteady or you

want the doors to close easier, adjust the refrigerator's tilt using

the instructions below:

1. Check the installation location to be sure that you have the

proper clearance for the refrigerator. See the "Location

Requirements" section.

2. Plug into a grounded 3 prong outlet.

3. Move the refrigerator into its final position.

4. Open the refrigerator and freezer doors to locate the leveling

bolts at the left and right of the refrigerator base. If your

refrigerator has a base grille, remove it. See "Base Grille"

earlier in this section.

[

E...JJ

1. Rear Leveling Bolt (yellow)

2. Front Leveling Bolt (silver)

NOTE: The yellow (top) bolt will adjust the rear of the

refrigerator, and the silver (bottom) bolt will adjust the front of

the refrigerator.

Use a 1/2in. (12.70 mm) socket wrench to adjust the leveling

bolts. Turn the leveling bolt to the right to raise that side of the

refrigerator or turn the leveling bolt to the left to lower that

side. It may take several turns of the leveling bolts to adjust

the tilt of the refrigerator.

NOTE: Be careful not to unscrew the leveling bolts too much

when lowering the refrigerator. The bolt head will start to

come away from the refrigerator when in the lowest position.

If the screw does come out of the rear roller bracket, the

compartment access cover on the back of the refrigerator will

have to be removed to reinstall the bolt.

Adjust the front leveling bolt to bring the refrigerator top

parallel with the cabinet above the refrigerator. For standard

cabinets, leave approximately 1/8in. (3.18 mm) gap between

the top hinges and the cabinet. For full-overlay cabinets,

leave 1/4in. (6.35 mm) gap for leveling. If you do not have a

cabinet above the refrigerator, simply adjust the refrigerator to

make it level.

1. Fer standard cabinets, leave _in. (3.18 mm)

minimum clearance for leveling the refrigerator.

For full-overlay cabinets, leave _ in. (6.35 mm)

minimum clearance for leveling and door

clearance.

2. Front of the refrigerator.

7. Adjust the rear leveling bolt to bring the refrigerator level with

the side cabinets or cabinet end panels.

8. If you want, you may now use the four leveling bolts to raise

the refrigerator to close the gap between the refrigerator top

hinge and the cabinet opening. Check that all four rollers still

touch the floor and that the cabinet doors above the

refrigerator open all the way.

9. Replace the base grille.

S(} (:,:_

Your new refrigerator may make sounds that your old one didn't

make. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard

surfaces, such as the floor, walls, and cabinets, can make the

sounds seem louder. The following describes the kinds of sounds

and what may be making them.

• If your product is equipped with an ice maker, you will hear a

buzzing sound when the water valve opens to fill the ice

maker for each cycle.

Your refrigerator is designed to run more efficiently to keep

your food items at the desired temperatures and to minimize

energy usage. The high efficiency compressor and fans may

cause your refrigerator to run longer than your old one. You

may also hear a pulsating or high-pitched sound from the

compressor or fans adjusting to optimize performance.

• You may hear the evaporator fan motor circulating air through

the refrigerator and freezer compartments. The fan speed

may increase as you open the doors or add warm food.

• Rattling noises may come from the flow of refrigerant, the

water line, or items stored on top of the refrigerator.

• Water dripping on the defrost heater during a defrost cycle

may cause a sizzling sound.

• As each cycle ends, you may hear a gurgling sound due to

the refrigerant flowing in your refrigerator.

• Contraction and expansion of the inside walls may cause a

popping noise.

• You may hear air being forced over the condenser by the

condenser fan.

• You may hear water running into the drain pan during the

defrost cycle.

REFRIGERATOR USE

In order to ensure proper temperatures, you need to permit

airflow between the two sections. Cold air enters the bottom of

the freezer section and moves up. It then enters the refrigerator

section through the top vent. Air then returns to the freezer as

shown.

±±

Do not block any of these vents with food such as soda, cereal,

bread, etc. If the vents are blocked, airflow will be prevented and

the temperature controls will not function properly.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To prevent

odor transfer from food, wrap or cover foods tightly.

Electronic Controls

For your convenience, your controls are preset at the factory.

When installing your refrigerator, make sure that the controls are

still preset to the "mid-settings" as shown. To view settings,

press the POWER ON/OFF button.

Warmer

Cooler

Freezer

Warmer

Cooler

Refrigerator

IMPORTANT:

• Your product will not cool when the Power Control is set to

OFR

The Refrigerator Control adjusts the refrigerator compartment

temperature. The Freezer Control adjusts the freezer

compartment temperature. Press the UP ARROW to make

the temperature warmer. Press the DOWN ARROW to make

the temperature colder.

Wait 24 hours before you put food into the refrigerator. If you

add food before the refrigerator has cooled completely, your

food may spoil.

NOTE: Adjusting the Refrigerator and Freezer Controls to a

higher (colder) setting will not cool the compartments any

faster.

The preset settings should be correct for normal household

usage. The controls are set correctly when milk or juice is as

cold as you like and when ice cream is firm.

If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

Adjusting Controls

If you need to adjust temperatures, adjust the refrigerator

temperature first. Wait 24 hours between adjustments and then

recheck the temperatures.

CONDITION/REASON:

REFRIGERATOR too cold

Controls not set correctly for your

conditions

REFRIGERATOR too warm

Door opened often, large amount of

food added or room temperature

very warm

FREEZER too cold

Controls not set correctly for your

conditions

FREEZER too warm/too little ice

Door opened often, or large amount

of food added or very cold room

temperature (can't cycle often

enough) or heavy ice usage

SETTING

ADJUSTMENT:

Press REFRIGERATOR

Control UP ARROW to

move the control to the

next higher setting

Press REFRIGERATOR

Control DOWN

ARROW to move the

control to the next

lower setting

Press FREEZER

Control UP ARROW to

move the control to the

next higher setting

Press FREEZER

Control DOWN

ARROW to move the

control to the next

lower setting

Cut Hazard

Use a sturdy glass when dispensing ice or water.

Failure to do so can result in cuts.

Depending on your model, you may have one or more of the

following options: the ability to select either crushed or cubed

ice, a special light that turns on when you use the dispenser, or a

lock option to avoid accidental dispensing.

The ice dispenser

Ice dispenses from the ice maker storage bin in the freezer. When

the dispenser lever is pressed:

• A trap door opens in a chute between the dispenser and the

ice bin. Ice moves from the bin and falls through the chute.

• When you release the dispenser lever, the trap door closes

and the ice dispensing stops. The dispensing system will not

operate when the freezer door is open.

Some models dispense both cubed and crushed ice. Before

dispensing ice, select which type of ice you prefer. The button

controls are designed for easy use and cleaning.

• For cubed ice, press the CUBE button until the red indicator

appears in the window above the CUBE button.

ICE

CRUSH CUBE

• For crushed ice, press the CRUSH button until the red

indicator appears in the window above the CRUSH button.

For crushed ice, cubes are crushed before being dispensed. This

may cause a slight delay when dispensing crushed ice. Noise

from the ice crusher is normal, and pieces of ice may vary in size.

When changing from CRUSH to CUBE, a few ounces of crushed

ice will be dispensed along with the first cubes.

To dispense ice:

1. Press button for the desired type of ice.

2. Press a sturdy glass against the ice dispenser lever. Hold the

glass close to the dispenser opening so ice does not fall

outside of the glass.

IMPORTANT: You do not need to apply a lot of pressure to

the lever in order to activate the ice dispenser. Pressing hard

will not make the ice dispense faster or in greater quantities.

Remove the glass to stop dispensing.

NOTE: The first few batches of ice may have an off-flavor

from new plumbing and parts. Throw the ice away. Also, take

large amounts of ice from the ice bin, not through the

dispenser.

The water dispenser

If you did not flush the water system when the refrigerator was

first installed, press the water dispenser bar with a glass or jar

until you draw and discard 2 to 3 gal. (8 to 12 L) or approximately

6 to 7 minutes of water after water begins dispensing. It will take

3 to 4 minutes for the water to begin dispensing. The water you

draw and discard cleans the system and helps clear air from the

lines. Allow several hours for the refrigerator to cool down and

chill water.

IMPORTANT: Depending on your model, the small removable

tray at the bottom of the dispenser is designed to catch small

spills and allow for easy cleaning. There is no drain in the tray.

The tray can be removed from the dispenser and carried to the

sink to be emptied or cleaned.

To dispense water:

1. Press a glass against the water dispenser lever.

2. Remove the glass to stop dispensing.

NOTE: Dispense enough water every week to maintain a fresh

supply.

The dispenser light

The dispenser area has a light. It can be turned on manually by

pressing the ON button at the right hand side of the control

panel. The red indicator above the ON button will appear.

On some models: Whenever you use the dispenser, the lever will

automatically turn the light on.

LIGHT

OFF ON

NOTE: See the "Changing the Light Bulbs" section for

information on changing the dispenser light bulb.

On models without crushed ice, the light switch is a rocker-style

type. Push the switch to turn the light on, and push again to turn

the light off.

The dispenser lock (on some models)

Your dispenser can be turned off for easy cleaning or to prevent

accidental dispensing by small children and pets. To turn off the

dispenser, press the LOCK button. The indicator will appear

above the LOCK button and the ice and water dispensers will not

work. To unlock the dispenser, press the UNLOCK button until

the indicator appears. Then continue to dispense ice or water as

usual.

DISPENSER

LOCK UNLeCK

NOTE: The lock feature does not shut off power to the product,

to the ice maker, or to the dispenser light. It simply deactivates

the dispenser levers.

The water filter indicator light

The water filter indicator light will help you know when to change

your water filter cartridge. The light is located at the top of the

refrigerator compartment. The light will change from green to

yellow. This tells you that it is almost time to change the water

filter cartridge (90% of the filter life has been used). It is

recommended that you replace the water filter cartridge when the

water filter indicator light changes to red OR water flow to your

water dispenser or ice maker decreases noticeably. See

"Changing a water filter cartridge" later in this section.

NOTE: Do not use with water that is microbiologically unsafe

or of unknown quality without adequate disinfection before

or after the system.

Warmer Warmer

Cooler Cooler

Freezer

Refrigerator

After changing the water filter cartridge, reset the water filter

indicator light by pressing and holding the WATER FILTER button

for 2 seconds. The indicator light will change from red to green

when the system is reset.

Changing a water filter cartridge

The water filter is located below the freezer compartment door.

1. Locate the water filter cartridge cap in the front base grille

below the freezer compartment door. Rotate the cap

counterclockwise to a vertical position and pull the cap and

filter cartridge out through the base grille.

NOTE: There will be water in the cartridge. Some spilling may

Occur.

Rotate the cartridge cap to a horizontal position as shown in

Step 5. See "Changing a water filter cartridge" earlier in this

section.

NOTE: The cartridge cap may not be even with the base

grille.

Ordering replacement filters

To order more water filter cartridges, see the "Accessories"

section in the "Assistance or Service" section.

Remove the cartridge cap by sliding it off the end of the old

cartridge. The cap will slide to the left or right. DO NOT

DISCARD THE CAR

Take the new cartridge out of its packaging and remove

protective cover from o-rings.

To turn the ice maker on/off:

The on/off switch for the ice maker is a wire shutoff arm located

on the side of the ice maker.

1. Toturn the ice maker on, simply lower the wire shutoff arm.

NOTE: Your ice maker has an automatic shutoff. As ice is

made, the ice cubes will fill the ice storage bin and the ice

cubes will raise the wire shutoff arm to the OFF (arm up)

position.

2. To manually turn the ice maker off, lift the wire shutoff arm to

the OFF (arm up) position and listen for the click to make sure

the ice maker will not continue to operate.

4. Slide the cartridge cap onto the new cartridge as shown in

Step 2.

5. With cartridge cap in the vertical position, push the new filter

cartridge into the base grille until it stops. Rotate the cartridge

cap clockwise to a horizontal position.

To remove and replace the ice bin:

1. Pull the covering panel out from the bottom and then slide it

back toward the rear.

2. Lift the wire shutoff arm so it clicks into the OFF (up)

position. Ice can still be dispensed, but no more can be

made.

3. Lift up the front of the storage bin and pull it out.

6= RUN WATER THROUGH THE DISPENSER UNTIL THE

WATER RUNS CLEAR (about 2-3 gal. or 6-7 min.). This will

clean the system and clear air from the lines. Additional

flushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out

of the dispenser.

Using the dispenser without the water filter

You can run the dispenser without a water filter cartridge. Your

water will not be filtered. Ifyou run the dispenser without a water

filter cartridge, keep the cartridge cap and replace it in the base

grille for future use.

1. Remove the water filter cartridge. See "Changing a water

filter cartridge" earlier in this section. Then slide the cartridge

cap off the end of the filter cartridge. DO NOT DISCARD THE

CAP.

2. With the cartridge cap in the vertical position, insert the cap

into the base grille until it stops.

4. Replace the bin by pushing it in all the way or the dispenser

will not work. Push the wire shutoff arm down to the ON

position to restart ice production. Make sure the door is

closed tightly.

To care for ice storage bin:

1. Empty the ice bin. Use warm water to melt the ice if

necessary. Never use anything sharp to break up the ice in

the bin. This can cause damage to the ice container and the

dispenser mechanism.

2. Wash ice bin with a mild detergent, rinse well and dry

thoroughly. Do not use harsh or abrasive cleaners or solvents.

REMEMBER:

• Allow 24 hours to produce the first batch of ice.

• Discard the first three batches of ice produced to avoid

impurities that may be flushed out of the system.

• The quality of your ice will be only as good as the quality of

the water supplied to your ice maker.

Avoid connecting the ice maker to a softened water supply.

Water softener chemicals (such as salt) can damage parts of

the ice maker and lead to poor quality ice. If a softened water

supply cannot be avoided, make sure the water softener is

operating properly and is well maintained.

It is normal for the ice cubes to be attached at the corners.

They will break apart easily.

Do not force the wire shutoff arm up or down.

Do not store anything on top of the ice maker or in the ice

storage bin.

REFRIGERATOR

FEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Accessories"

section.

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when re-

moving them to avoid impact from dropping.

Your model may have glass or wire shelves. Store similar foods

together and adjust the shelves to fit different heights. This

reduces the time the refrigerator door is open and saves energy.

Slide-out Shelves (on some models)

To remove and replace a shelf in a metal frame:

1. Pull the shelf forward to the stop. Tilt the front of the shelf up

and lift it slightly as you pull the shelf from the frame.

2. Replace the shelf by guiding it back into the slots on the

frame and pushing the shelf in past the stop.

Shelves and Shelf Frames

To remove and replace a shelf/frame:

1. Remove the shelf/frame by tilting it up at the front and lifting it

out of the shelf supports.

2. Replace the shelf/frame by guiding the rear shelf hooks into

the shelf supports. Tilt the front of the shelf up until rear shelf

hooks drop into the shelf supports. Check to make sure that

the shelf is securely in position.

Crisper and Meat Drawers

To remove and replace the crisper and meat drawers:

1. Slide crisper or meat drawer straight out to the stop. Lift the

front of drawer with one hand while supporting the bottom of

drawer with other hand and slide the drawer out the rest of

the way.

2. Replace the crisper or meat drawer by sliding it back in fully

past the drawer stop.

Crisper and Meat Drawer Covers

To remove and replace the crisper or meat drawer covers:

1. Remove the crisper and meat drawer. Press up in center of

crisper glass insert until it rises above the plastic frame.

Holding the crisper glass firmly, carefully slide the glass insert

forward to remove.

2. Lift crisper cover frame and remove. Repeat steps to remove

the meat drawer cover.

3. Replace back of meat drawer cover frame into supports or

slides on side walls of the refrigerator and lower or slide the

front of the cover frame into place.

4. Slide rear of glass insert into cover frame and lower front into

place. Repeat steps to replace the crisper cover.

Meat storage guide

Store most meat in original wrapping as long as it is airtight and

moisture-proof. Rewrap if necessary. See the following chart for

storage times. When storing meat longer than the times given,

freeze the meat.

Fresh fish or shellfish .................. use same day as purchased

Chicken, ground beef, variety meat (liver, etc.) ......... 1-2 days

Cold cuts, steaks/roasts ........................................... 3-5 days

Cured meats ............................................................ 7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or

plastic containers with tight lids.

....... k .... ,J •

You can control the amount of humidity in the moisture-sealed

crisper. Adjust the control to any setting between LOW and

HIGH.

LOW (open) lets moist air out of the crisper for best storage of

fruits and vegetables with skins.

• Fruit: Wash, let dry and store in refrigerator in plastic bag

or crisper. Do not wash or hull berries until they are ready

to use. Sort and keep berries in original container in

crisper, or store in a loosely closed paper bag on a

refrigerator shelf.

• Vegetables with skins: Place in plastic bag or plastic

container and store in crisper.

HIGH (closed) keeps moist air in the crisper for best storage of

fresh, leafy vegetables.

• Leafy vegetables: Wash in cold water, drain and trim or

tear off bruised and discolored areas. Place in plastic bag

or plastic container and store in crisper.

Humidity control location:

• Humidity Control on crisper drawer (Style 1 - on left)

• Humidity Control on crisper cover (Style 2 - on right)

I_ Humidity Centre/

...............

High 5 4 3 2 ! LOW

To remove and replace the beverage drawer:

1. Remove the beverage drawer by sliding it straight out to the

stop. Lift up at the front and slide the beverage drawer out

the rest of the way.

2. Replace the beverage drawer by sliding it back in fully past

the stop.

To remove and replace the beverage drawer shield:

1. Remove the beverage drawer shield by grasping it at the

bottom center. Pull up in the center while turning the shield

slightly to one side.

2. Replace the shield by grasping it at the bottom center and

inserting one side into the beverage drawer cover.

3. Carefully bend the shield at the center to insert the other side

into the cover.

To remove and replace the wine rack (left) or can/bottle

rack (right):

1. Remove the rack by pulling it straight out from the shelf.

2. Replace the rack by sliding it in between the shelf and the

wall of the refrigerator.

NOTE: For long-term storage, store eggs in a covered container

or in their original carton on an interior shelf.

FREEZER FEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Accessories"

section.

To remove and replace the shelf:

1. Remove the shelf by lifting it up and pulling it straight out.

2. Replace the shelf by putting it over the supports and lowering

it into place.

Frozen food storage guide

Storage times will vary according to the quality and type of food,

the type of packaging or wrap used (should be airtight and

moisture-proof), and the storage temperature. Ice crystals inside

a sealed package are normal. This simply means that moisture in

the food and air inside the package have condensed, creating ice

crystals.

Put no more unfrozen food into the freezer than will freeze within

24 hours (no more than 2 to 3 Ibs of food per cubic foot [907-

1,350 g per L] of freezer space). Leave enough space in the

freezer for air to circulate around packages. Be careful to leave

enough room for the door to close tightly.

For more information on preparing food for freezing, check a

freezer guide or reliable cookbook.

The freezer basket can be used to store bags of frozen fruits and

vegetables that may slide off freezer shelves.

To remove and replace the freezer basket:

1. Remove basket by sliding it out to the stop.

2. Lift the front of the basket and slide it out the rest of the way.

Large door bins hold gallon containers and the smaller door bins

hold 2-liter bottles. The door bins are removable for easy

cleaning and adjusting.

NOTE: Place large door bins in the upper part of the refrigerator

door so the door will close properly. Small door bins will fit in

either the upper or lower part of the door.

To remove and replace the door bins:

1. Remove the bin by lifting it up and pulling it out.

2. Replace the bin by insert the hooks into the slots on both

sides of the refrigerator door. Push the bin down to lock it into

place.

3. Replace the basket by positioning it on the side wall guide

rails. Lift the basket front slightly while pushing it past the

guide rail stops and slide basket in the rest of the way.

DOOR FEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Assistance or

Service" section.

The door rails may be removed for easier cleaning.

Snap-on Door Rails

To remove and replace the rails:

1. Remove the rails by pushing in slightly on the front of the

bracket while pulling out on the inside tab. Repeat these

steps for the other end of the rail.

2. Replace the rails by aligning the ends of the brackets with the

buttons on the sides of the door liner. Firmly snap bracket

and rail assembly onto the tabs above the shelf as shown.

Drop-in Door Rails

To remove and replace the rails:

1. Remove the rails by pulling straight up on each end of the rail.

2. Replace the rails by sliding the shelf rail into the slots on the

door and pushing the rail straight down until it stops.

REFRIGERATOR CARE

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion,

or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to prevent

odors from building up. Wipe up spills immediately.

Cleaning your refrigerator

1. Unplug refrigerator or disconnect power.

2. Remove all removable parts from inside, such as shelves,

crispers, etc.

3. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

• Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning

waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on plastic parts, interior

and door liners or gaskets. Do not use paper towels,

scouring pads, or other harsh cleaning tools. These can

scratch or damage materials.

• To help remove odors, you can wash interior walls with a

mixture of warm water and baking soda (2 tbs. to 1 qt.

[26 g to .95 L] of water).

Wash stainless steel and painted metal exteriors with a clean

sponge or soft cloth and a mild detergent in warm water. Do

not use abrasive or harsh cleaners. Dry thoroughly with asoft

cloth. For additional protection against damage to painted

metal exteriors, apply appliance wax (or auto paste wax) with

a clean, soft cloth. Do not wax plastic parts.

NOTE: To keep your Stainless Steel refrigerator looking like

new and to remove minor scuffs or marks, it is suggested that

you use the manufacturer's approved Stainless Steel Cleaner

& Polish.

IMPORTANT: This cleaner is for Stainless Steel parts only.

Do not allow the Stainless Steel Cleaner & Polish to come into

contact with any plastic parts such as the trim pieces,

dispenser covers or door gaskets. If accidental contact does

occur, clean plastic part with a sponge and mild detergent in

warm water. Dry thoroughly with a soft cloth. To order the

cleaner, see the "Accessories" section.

There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every 2 to 3

months to ensure maximum efficiency.

If you need to clean the condenser:

• Remove the base grille. See "Base Grille" or "Door

Removal" section.

• Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

Plug in refrigerator or reconnect power.

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to

replace the bulb with one of the same size and shape. The

dispenser light requires a heavy duty 10-watt bulb. All other lights

require a 40-watt appliance bulb. Replacement bulbs are

available from your dealer.

1. Unplug refrigerator or disconnect power.

2. Remove light shield when applicable as shown.

NOTE: To clean a light shield, wash it with warm water and a

liquid detergent. Rinse and dry the shield well.

3. Remove light bulb and replace with one of the same size,

shape and wattage.

4. Replace light shield when applicable as shown.

5. Plug in refrigerator or reconnect power.

Dispenser Light (on some models}

Reach through the dispenser area to remove and replace light

bulb.

Control Panel Light

Reach behind the refrigerator control panel to remove and

replace light bulb.

Crisper Light or Upper Freezer Light (on some models):

• Remove light shield by grasping the top center of the shield

and pulling forward while turning it slightly to one side. If

necessary, remove top crisper drawer to access crisper light

shield.

Replace the light shield by inserting the tabs on one end into

the slotted holes in the refrigerator or freezer liner. Then,

carefully bend the shield at the center to insert the tabs on

the other end.

Lower Freezer Light Beneath Ice Bin (on some models):

• Remove the light shield by grasping the sides and squeezing

in toward the center. Once the side hooks of shield are free

from the freezer lining, pull down the shield.

Replace the light shield by squeezing the sides toward the

center and inserting the side hooks into the slotted holes.

Once the side hooks are in place, snap the front tab into the

slotted hole.

1. Dispenser Light

If the power will be out for 24 hours or less, keep both refrigerator

doors closed to help food stay cold and frozen.

If the power will be out for more than 24 hours, do one of the

following:

• Remove all frozen food and store it in a frozen food locker.

Place 2 Ibs (907 g) of dry ice in the freezer for every cubic foot

(28 L) of freezer space. This will keep the food frozen for two

to four days.

If neither a food locker nor dry ice is available, consume or

can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially filled

one. A freezer full of meat stays cold longer than a freezer full of

baked goods. If you see that food contains ice crystals, it may be

refrozen, although the quality and flavor may be affected. If the

condition of the food is poor, dispose of it.

Vacations

If you choose to leave the refrigerator on while you're away, use

these steps to prepare your refrigerator before you leave.

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker:

• Raise wire shutoff arm to OFF (up) position.

• Shut off water supply to the ice maker,

3. Empty the ice bin.

If you choose to turn the refrigerator off before you leave, follow

these steps.

1. Remove all food from the refrigerator,

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day •

ahead of time.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position.

3. Depending on your model, turn the Thermostat Control (or

Refrigerator Control, depending on the model) to OFR See

the "Using the Controls" section.

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and

mold from building up.

Moving

When you are moving your refrigerator to a new home, follow

these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• Disconnect the water line from the back of the

refrigerator.

• When the last load of ice drops, raise the wire shutoff arm •

to the OFF (up) position.

2. Remove all food from the refrigerator and pack all frozen food

in dry ice.

3. Depending on your model, turn the Thermostat Control (or

Refrigerator Control, depending on the model) to OFR See

the "Using the Controls" section.

4. Unplug refrigerator.

5. Empty water from the defrost pan.

6. Clean, wipe, and dry thoroughly.

7. Take out all removable parts, wrap them well, and tape them

together so they don't shift and rattle during the move.

8. Depending on the model, raise the front of the refrigerator so

it rolls more easily OR screw in the leveling legs so they don't

scrape the floor. See the "Leveling Refrigerator" section.

9. Tape the doors shut and the power cord to the refrigerator

cabinet.

When you get to your new home, put everything back and refer to

the "Installation Instructions" section for preparation instructions.

Also, if your refrigerator has an automatic ice maker, remember to

reconnect the water supply to the refrigerator.

TROUBLESHOOTING

Trythe solutions suggested here first in order to avoid the

cost of an unnecessary service call.

Your refrigerator will not operate

• Is the power supply cord unplugged? Plug into a grounded

3 prong outlet.

• Has a household fuse or circuit breaker tripped? Replace

the fuse or reset the circuit breaker.

• Is the refrigerator or freezer control turned to the OFF

position? Refer to the "Using the Controls" section.

• Is the refrigerator defrosting? Recheck to see if the

refrigerator is operating in 30 minutes. Your refrigerator will

regularly run an automatic defrost cycle.

Is the refrigerator not cooling? For models with digital

controls, turn the unit OFF then ON again to reset. See the

"Using the Controls" section. If this does not correct the

problem, call for service,

The lights do not work

• Is the power supply cord unplugged? Plug into a grounded

3 prong outlet.

• Is a light bulb loose in the socket or burned out? See the

"Changing the Light Bulb(s)" section.

There is water in the defrost drain pan

• Is the refrigerator defrosting? The water will evaporate, It is

normal for water to drip into the defrost pan.

• Is it more humid than normal? When it is humid, expect that

the water in the defrost pan will take longer to evaporate.

The motor seems to run too much

Is the room temperature hotter than normal? The motor

will run longer under warm conditions. At normal room

temperatures, expect your motor to run about 40% to 80% of

the time. Under warmer conditions, it will run even more.

Has a large amount of food just been added to the

refrigerator? Adding a large amount of food warms the

refrigerator. The motor normally will run longer to cool the

refrigerator back down.

Are the doors opened often? The motor will run longer

when this occurs, Conserve energy by getting all items out at

one time, keeping food organized, and closing the door as

soon as possible,

Are the controls not set correctly for the surrounding

conditions? Refer to the "Using the Controls" section,

Are the doors not closed completely? Close the doors

firmly. If they do not close completely, see "The doors will not

close completely" later in this section,

Are the condenser coils dirty? This prevents air transfer and

makes the motor work harder. Clean the condenser coils,

Refer to the "Cleaning" section.

Are the door gaskets not sealed all the way around?

Contact a technician or other qualified person.

NOTE: Your new refrigerator will run longer than your old one

due to its high-efficiency motor.

The refrigerator seems to make too much noise

• The sounds may be normal for your refrigerator. See the

"Normal Sounds" section.

The ice maker is not producing ice or not enough ice

• Has the ice maker just been installed? Wait 72 hours for full

ice production to begin, Once your refrigerator is cooled, the

ice maker should produce 70 to 120 cubes every 24 hours.

Is the freezer temperature cold enough to produce ice?

Wait 24 hours after ice maker hookup for ice production. See

the "Using the Controls" section.

Is the ice maker wire shutoff arm in the OFF (arm up)

position (on some models)? Lower the wire shutoff arm to

the ON (arm down) position. See the "Ice Maker and Storage

Bin/Bucket" section.

Is the ice maker switch in the OFF (right) position (on

some models)? Move ice maker switch to the ON (left)

position, See the "Ice Maker and Storage Bin/Bucket"

section.

Is the water line shutoff valve to the refrigerator turned

on? Turn on the water valve, See the "Water Supply

Connection" section,

Does the ice maker mold have water in it or has no ice

been produced? Make sure your refrigerator has been

connected to a water supply and the supply shutoff valve is

turned on. See the "Water Supply Connection" section.

Is an ice cube jammed in the ice maker ejector arm?

For models with an interior ice bin, remove the ice from the

ejector arm with a plastic utensil. For models with an ice

bucket located on the freezer door, access the ice maker by

depressing the ice sensor door on the upper left side of the

freezer interior. While depressing the sensor door, lift the ice

maker service door and remove the ice from the ejector with

a plastic utensil. See the "Ice Maker and Storage Bin/Bucket"

section.

Has a large amount of ice just been removed? Allow 24

hours for ice maker to produce more ice.

• Are the controls set correctly? See the "Using the Controls"

section.

Is there a water filter installed on the refrigerator? The

filter may be clogged or installed incorrectly, Check the filter

installation instructions to ensure that the filter was installed

correctly and is not clogged. If installation or clogging is not a

problem, call a technician or other qualified person,

NOTE: If not due to any of the above, there may be a problem

with the water line. Call for service.

Off-taste, odor or gray color inthe ice

• Are the plumbing connections new, causing discolored or

off-flavored ice? Discard the first few batches of ice.

• Have the ice cubes been stored too long? Throw old ice

away and make a new supply.

• Does the freezer and ice bin or bucket need to be

cleaned? See the "Cleaning" or "Ice Maker and Storage Bin/

Bucket" section,

• Has food in the freezer or refrigerator been wrapped

properly? Use airtight, moisture-proof packaging to help

prevent odor transfer to stored food.

• Does the water contain minerals (such as sulfur)? A filter

may need to be installed to remove the minerals.

Is there a water filter installed on the refrigerator? Gray or

dark discoloration in ice indicates that the water filtration

system needs additional flushing. Run additional water

through the water dispenser to flush the water filtration

system more thoroughly (at least 2 to 3 gal. [8 to 12 L] or 6 to

7 minutes initially). Discard discolored ice.

The ice dispenser will not operate properly

• Is the freezer door closed completely? Push the door firmly

shut, If it will not shut all the way, see "The doors will not

close completely" later in this section.

Is the ice bin or bucket installed correctly? For models

with an interior ice bin, push the ice bin in all the way. If the

ice bin does not go in all the way, it may not be put in straight.

Pull it out and try again, For models with an ice bucket

located on the freezer door, the bucket should sit level, To

remove the bucket, press the release button on the right side

of the bucket and lift straight up, Replace the bucket in the

door making sure it is properly aligned and snapped securely

into place. Refer to the "Ice Maker and Storage Bin/Bucket"

section,

Has the wrong ice been added to the bin or bucket? Use

only cubes produced by the current ice maker. If other cubes

have been added, remove all cubes and check to see that

none have become stuck in the delivery chute,

• Has the ice frozen in the ice bin or bucket? Shake the ice

bin or bucket to separate cubes. If cubes do not separate,

empty bin or bucket and wait 24 hours for ice to restock.

Has the ice melted around the auger (metal spiral) in the

ice bucket? Dump the ice cubes and clean the ice bucket

completely. Allow 24 hours for the ice maker to restock. Do

not try to remove the melted ice with a sharp object, You

could damage the ice bucket,

• Is ice stuck in the delivery chute? Clear the ice from the

delivery chute with a plastic utensil. Do not use anything

sharp to remove the ice. You could cause damage.

Is the ice dispenser stalling while dispensing "crushed"

ice? Stop dispensing ice. Change the ice button from

"crushed" to "cubed." Depress the ice dispenser arm using a

sturdy glass. If cubed ice dispenses correctly, depress the

button for "crushed" ice and begin dispensing again. Refer to

the "Water and Ice Dispensers" section.

• Is there ice in the bucket? See "The ice maker is not

producing ice" earlier in this section.

Has the dispenser arm been held in too long? Release

dispenser arm. Ice will stop dispensing when the arm is held

in too long. Wait three minutes for dispenser motor to reset

before using again. It is best to take large amounts of ice

directly from the ice bin or bucket, not through the dispenser.

Water flow from the dispenser decreases noticeably

Is there a water filter installed on the refrigerator?

The filter may be full or incorrectly installed. Remove the

water filter cartridge. See the "Water Filtration System"

section. Operate the dispenser. If the water flow increases

noticeably, replace the filter.

The dispenser water is not cool enough

• Has the refrigerator been newly installed? Allow 24 hours

for the refrigerator to cool completely.

Ice bucket difficult to remove

Is the ice bucket difficult to remove (on some models)?

For models with an ice bucket located on the freezer door,

select "cubed" ice. Using a sturdy glass, quickly depress and

release the ice dispenser arm. Open the freezer door, depress

the release button on the ice bucket and lift upward. Refer to

the "Ice Maker and Storage Bin/Bucket" section.

The water dispenser will not operate properly

Has the water system not filled? The water system needs

to be filled the first time it is used. Use a sturdy container to

depress the water dispenser bar until the water begins to •

flow. Flush the water system by dispensing and discarding

2 to 3 gal. (8 to 12 L) of water. Cleaning the system will take

approximately 6 to 7 minutes and will help clear air from the

line. Additional flushing may be required in some households.

See the "Water and Ice Dispensers" section. •

Is the water shutoff valve not turned on or the water line

connected at the source? Make sure the water shutoff valve

is turned on and the water source is connected to the

refrigerator. See the "Water Supply Connection" section.

Is the water shutoff valve clogged or incorrectly installed?

See the "Water Supply Connection" section. If clogging or

installation is not a problem, call for service or contact a

plumber.

• Is there a kink in the home water source line? If you find or

suspect a kink in the water line, call for service. •

Is there a water filter installed on the refrigerator? The

filter may be clogged or incorrectly installed. First, check the

filter installation instructions to ensure that the filter was

installed correctly and is not clogged. If installation or

clogging is not a problem, call for service.

Water or ice is leaking from the dispenser

Is the glass not being held under the ice dispenser long

enough, causing the ice to spill? Hold the container under

the ice chute for two to three seconds after releasing the

dispenser lever. Water or ice may continue to dispense during

this time.

• Is an ice cube stuck in the chute and holding the trap

door open? Remove the cube.

Is there a water filter installed on the refrigerator? The

water filtration system may have air inthe lines, causing water

to drip. Additional flushing may help clear air from the lines.

Normal dispenser use should flush air from the lines within 24

to 72 hours.

Has a large amount of water been recently dispensed?

Allow 24 hours for the water to cool completely.

Has water not been recently dispensed? The first glass of

water may not be cool. Discard the first glass of water.

The divider between the two compartments iswarm

The warmth is probably due to normal operation of the

automatic exterior moisture control. If still concerned, call for

service.

Temperature is too warm

Are the air vents blocked in either compartment? This

prevents the movement of cold air from the freezer to the

refrigerator. Remove any objects from in front of the air vents.

See the "Ensuring Proper Air Circulation" section for the

location of air vents.

Are the door(s) opened often? The refrigerator will warm

when this occurs. Keep the refrigerator cool by getting all

items out at one time, keeping food organized, and closing

the door as soon as possible.

Has a large amount of food just been added to the

refrigerator or freezer? Adding a large amount of food

warms the refrigerator. It can take several hours for the

refrigerator to return to the normal temperature.

Are the controls set correctly for the surrounding

conditions? See the "Using the Controls" section.

Is the refrigerator not cooling? For models with digital

controls, turn the unit OFF then ON again to reset. See the

"Using the Controls" section. If this does not correct the

problem, call for service.

There is interior moisture buildup

• Are the air vents blocked in the refrigerator? Remove any

objects from in front of the air vents. See the "Ensuring

Proper Air Circulation" section for the location of air vents.

• Are the door(s) opened often? Avoid humidity buildup by

getting all items out at one time, keeping food organized, and

closing the door as soon as possible.

• Is the room humid? It is normal for moisture to build up

inside the refrigerator when the room air is humid.

• Is the food packaged correctly? Check that all food is

securely wrapped. Wipe off damp food containers before

placing in the refrigerator.

• Are the controls set correctly for the surrounding

conditions? See the "Using the Controls" section.

• Was a self-defrost cycle completed? It is normal for

droplets to form after the refrigerator self-defrosts.

The doors will not close completely

• Are food packages blocking the door open? Rearrange

containers so that they fit more tightly and take up less

space.

Is the ice bin or ice bucket out of position? For models

with an interior ice bin, push the ice bin in all the way. If the

ice bin does not go in all the way, it may not be put in straight.

Pull it out and try again. For models with an ice bucket

located on the freezer door, the bucket should sit level. To

remove the bucket, press the release button on the right side

of the bucket and lift straight up. Replace the bucket in the

door making sure it is properly aligned and snapped securely

into place. See the "Ice Maker and Storage Bin/Bucket"

section.

Are the pans, shelves, bins, or baskets out of position?

Put the crisper cover and all pans, shelves, bins, and baskets

back into their correct positions. See the "Crisper and Crisper

Covers" section for more information.

• Are the gaskets sticking? Clean gaskets according to the

directions in the "Cleaning" section.

• Does the refrigerator wobble or seem unstable? Level the

refrigerator. See the "Door Closing" or "Leveling Refrigerator"

section, depending on your model.

Were the doors removed during product installation and

not properly replaced? Remove and replace the doors

according to the "Door Removal" section on some models, or

call a qualified service technician.

The doors are difficultto open

• Are the gaskets dirty or sticky? Clean gaskets according to

the directions in the "Cleaning" section.

Computer Troubleshooting (on some models)

See the "Computer and Software User Guide" for information

regarding your computer system.

ASSISTANCE

OR SERVICE

Before calling for assistance or service, please check

"Troubleshooting." It may save you the cost of a service call. If

you still need help, follow the instructions below.

When calling, please know the purchase date and the complete

model and serial number of your appliance. This information will

help us to better respond to your request.

If you need replacement parts

If you need to order replacement parts, we recommend that you

only use factory specified replacement parts. Factory specified

replacement parts will fit right and work right because they are

made with the same precision used to build every new

KitchenAid ®appliance.

To locate factory specified replacement parts in your area, call

our Customer Interaction Center telephone number or your

nearest designated service center.

Call the KitchenAid Customer Interaction Center

toll free: 1-800-422-1230.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Installation information.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

• Referrals to local dealers, repair parts distributors, and

service companies. KitchenAid designated service

technicians are trained to fulfill the product warranty and

provide after-warranty service, anywhere in the United States.

To locate the KitchenAid designated service company in your

area, you can also look in your telephone directory Yellow

Pages.

For further assistance

If you need further assistance, you can write to KitchenAid with

any questions or concerns at:

KitchenAid Brand Home Appliances

Customer Interaction Center

553 Benson Road

Benton Harbor, M149022-2692

Please include a daytime phone number in your correspondence.

La page charge ...

KitchenAid KSBS25FKBL02 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KSBS25FKBL02

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KSBS25FKBL02 Owner's manual

KitchenAid KSBS25FKBL02 Le manuel du propriétaire

Ce manuel convient également à

KitchenAid KSBS25FKBL02 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents