Heat & Glo Tiara Petite-B TiaraP Install Manual

Marque: Heat & Glo

Modèle: Tiara Petite-B TiaraP

Catégorie: Cheminées

Taper: Install Manual

WARNING

DO NOT DISCARD THIS MANUAL

CAUTION

• Important operating and

maintenance instructions

included.

• Leave this manual with

party responsible for use

and operation.

• Read, understand and

follow these instructions

for safe installation and

operation.

• Do not store or use gasoline or other À am-

mable vapors and liquids in the vicinity of this

or any other appliance.

• What to do if you smell gas

- Do not try to light any appliance.

Do not touch any electrical switch. Do not

use any phone in your building.

- Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

- If you cannot reach your gas supplier, call

the ¿ re department.

• Installation and service must be performed

by a quali¿ ed installer, service agency, or the

gas supplier.

WARNING: If the information in these

instructions is not followed exactly, a ¿ re

or explosion may result causing property

damage, personal injury, or death.

This appliance may be installed as an OEM installation in

manufactured home (USA only) or mobile home and must be

installed in accordance with the manufacturer's instructions and

the manufactured home construction and safety standard, Title

24 CFR, Part 3280 or Standard for Installation in Mobile Homes,

CAN/CSA Z240MH.

This appliance is only for use with the type(s) of gas indicated on

the rating plate.

Installation and service of this appliance should be

performed by quali¿ ed personnel. Hearth & Home

Technologies suggests NFI certi¿ ed or factory-trained

professionals, or technicians supervised by an NFI

certi¿ ed professional.

DO NOT

DISCARD

TIARA PETITE B

DIRECT VENT ROOM HEATER

Owner’s Manual

Installation and Operation

TIARAP-BK

TIARAP-BR

TIARAP-CES

Model:

O-T

O-T L

Tested and

Listed by

Portland

Oregon USA

OMNI-Test Laboratories, Inc.

CUS

In the Commonwealth of Massachusetts:

• installation must be performed by a licensed plumber or

gas ¿ tter.

See Table of Contents for additional Commonwealth of

Massachusetts requirements.

HOT SURFACES!

Glass and other surfaces are

hot during operation AND cool

down.

Hot glass will cause burns.

• Do not touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in the same room as

appliance

• Alert children and adults to hazards of high temperatures

High temperatures may ignite clothing or other

À ammable materials.

• Keep clothing, furniture, draperies and other combustibles

away.

Heat & Glo • Tiara Petite B • 7026-101 Rev. Q • 10/13

Read this manual before installing or operating this appliance.

Please retain this owner's manual for future reference.

Congratulations

Congratulations on selecting a Heat & Glo gas appliance - an

elegant and clean alternative to wood burning appliances.

The Heat & Glo gas appliance you have selected is designed

to provide the utmost in safety, reliability, and efficiency.

As the owner of a new appliance, you'll want to read and

carefully follow all of the instructions contained in this

Owner's Manual. Pay special attention to all Cautions and

Warnings.

This Owner's Manual should be retained for future reference.

We suggest that you keep it with your other important

documents and product manuals.

Your new Heat & Glo gas appliance will give you years of

durable use and trouble-free enjoyment. Welcome to the

Heat & Glo family of gas appliance products!

SAMPLE OF RATINGS LABEL

LOCATION: Hang tag attached to rear of appliance.

Serial No.

Model Name

Test Lab & Report No.

Manufactured Date

MINIMUM CLEARANCES TO COMBUSTIBLES / ESPACE MINIMUM AUX COMBUSTIBLES

Minimum clearances required from combustible construction for all appliance surfaces. / Espaces minimum exigés de la construction combustible aux surfaces de l’appareil.

A. Side of stove top to side wall 6" (15cm) D

u coté du poêle au coté du mur

B. Rear of stove to back wall 2" (5cm)

Le contrôle arrière au mur arrière

C. Corner of stove top to side wall-Left 2" (5cm)

Du coin arrière du poêle au mur de coté gauche

C. Corner of stove top to side wall-Right

2" (5cm) Du coin du dessus du po

êle au mur de coté droit (acces a la valve)

D. Minimum Alcove Height 43" (109cm) Ha

uteur minimum du plancher au plafond

E. Maximum Alcove Depth 36" (91cm) P

rofondeur maximum de l'alcove

F. Minimum Alcove Width 30" (76cm)

Largeur minimum de l'alcove

G. Mantle Clearance from stove top 19-1/2" (50cm) Espace libre du po

êle au manteau

H. Top of Stove to Alcove Ceiling 20-1/4" (51cm) Dessus de fourneau au plafond de chambrette

Date of Manufacture / Date du Manufacturier

2008 2009 2010 Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Jan

DO NOT REMOVE THIS LABEL / NE PAS ENLEVER L’ÉTIQUETTE Made in U.S.A. / Fait Aux États-Unis

HEARTH: A non-combustible hearth pad is not required. However, the floor beneath the stove must be stable, level, and strong enough to support the stove without a tipping hazard.

CHEMINÉE: Un coussinet non-combustible de cheminée n’est pas exigé. Cependant, le plancher en dessous du poêle doit être droit, à niveau et assez fort pour supporter le poêle sans le hasard de basculer.

This appliance equipped for altitudes 0-2000’ (0-610m) in USA; and in Canada for altitudes of 0-4500’ (0-1370m). In USA for Altitudes above 2000’, the vent configuration, orifice or combination

of both may need to be changed. See Owner’s Manual for information on making these changes. This appliance must be installed in accordance with local codes, if any (and Commonwealth

of Massachusetts approved); if none, follow ANSI Z223.1 in USA, CAN 1-B149 in Canada. Install and use only in accordance with manufacturer’s installation and operating instructions.

NOTE:

Have the gas supply line installed in accordance with local building codes by a qualified installer approved and/or licensed as required by the locality. (In the Commonwealth of Massachusetts, installation must

be performed by a licensed plumber or gas fitter.) /

Cet appareil est équipé pour les altitudes de 0-2000’ (0-610m) aux États-Unis; et au Canada pour les altitudes de 0-4500’ (0-1370m). Pour les

altitudes au dessus de 2000’ aux États-Unis, la configuration du ventilateur, son orifice ou les deux peuvent possiblement avoir à être changé. Voyez le manuel du propriétaire pour les

informations sur ces changements. Cet appareil doit être installé en accord avec les codes locaux, s’il-y-a lieu (et approuvé par dans la République de Massachusetts); sinon lisez ANSI

Z223.1/CAN 1-B149. Installez et utilisez en accords avec les instructions d’installation et d’opération du manufacturier. REMARQUE: Le conduit gaz doit être installé conformément aux codes

de construction locaux. L'installation doit être effectuée par un technicien qualifeé et/ou muni d'une licence de manière à respecter les règlements municipaux. (Dans la République de Massachusetts,

l'installation doit être effectuée par un plombier ou un installateur d'appareils à gaz agrée.)

0-2000 FT’ 0-2000FT

Input Rate on “HI” (BTU/Hr) 17,000 17,000 Puissance Évaluée à “HI” (BTU/Hr)

Input Rate on “LO” (BTU/Hr) 12,000 13,000 Puissance Évaluée à “LO” (BTU/Hr)

Maximum Output (BTU/Hr)** 14,500 13,500 Puissance Maximum (BTU/Hr**

Main Burner Orifice 49 56 Orifice du Brûleur Principal

Minimum Inlet Pressure

(Inches W.C.)

4.5” 11” Pression Minimum de la Valve (pouces W.C.)

Maximum Inlet Pressure

(Inches W.C.)

7.0” 14” Pression Maximum de la Valve (pouces W.C.)

anifold Pressure on

“HI”

(Inches W.C.)

3.5” 10” Pression du Collecteur d’ Échappement à “HI” (pouces W.C.)

**Max Venting, Blower On **Ventilation Maximum, Ventilateur Allumé

For use with Propane

Usage Au Gaz Propane

APPROVED FOR CANADA AND USA TO: ANSI Z21.88b-2003 / CSA 2.33b-2003 Vented Gas Fireplace Heaters, and applicable sections of UL307b Gas Burning Heating Appliances for Manufactured Homes and Recreational

Vehicles, CAN/CGA 2.17-M91 Gas Fired Appliances for use at High Altitudes. This appliance is manufactured for operation with Natural Gas. For conversion to propane Manufacturer's instructions must be used. This

appliance may be installed in a bedroom or bedsitting room; in Canada remote thermostat installation is required.

APPROUVÉ-POUR LE CANADA ET LES ÉTATS-UNIS: ANSI-Z21.88b-2003 / CSA 2.33b-2003 Fournaises au Gaz avec Ventilation, et les sections applicable de UL 307b Appareils de Chauffage Au Gaz our les Maisons Mobiles et les

Vehicules Motoriss, CAN/CGA 2.17-M91 Gas Fired Appliances for use at High Altitudes. Cet appareil est manufactur pour l'operation avec le Gaz Naturel. Pour une conversion au gaz propane les pices du Manufacturier et ses

instructions doivent tre utilises. Cet appareil peut tre utilis dans une chambre à coucher ou salle de sjour, au Canada, l'installation d'un thermostat à distance est exige.

FAN TYPE VENTED CIRCULATOR / VENTILATEUR CIRCULATOIRE

Blower Electrical Rating / Evaluation du Ventilateur

115 V., .55 Amps, 60 Hz, 150 Watts

Blower is Optional. Order Part #844-9370

Route power cord away from unit. Do not route

power cord under or over stove./

Éloignez le fil électrique

de l'appareil. Ne pas faire passer le fil électrique au dessus

ou en dessous de l'appareil.

P.4.1-02 Canada Minimum pipe (P.4.1-02 Le Canada tuyau minimum) 67.38% NG / 69.52% LP

Left

"A" measurement is from

stove top, not side

Right

For use with Natural Gas

Usage Au Gaz Naturel

7026-102

SAMPLE

VENTED GAS FIREPLACE HEATER

NOT FOR USE WITH SOLID FUEL

Serial No / Numéro du

Report No. / Rapport Numéro

061-S-47b-5 FOURNAISE AU GAZ AVEC VENTILATION

NE PAS UTILISER AVEC LE COMBUSTIBLE SOLIDE

MODEL / MODÈLE: TIARA PETITE (B)

A division of Hearth & Home Technologies Inc.

20802 Kensington Boulevard

Lakeville, MN 55044

007

O-T

O-T L

Tested and

Listed by

Portland

Oregon USA

OMNI-Test Laboratories, Inc.

CUS

Barcode

Heat & Glo • Tiara Petite B • 7026-101 Rev. Q • 10/13

- TABLE OF CONTENTS -

Section 1: Listing and Code Approvals

A. Appliance Certi¿ cations ......................4

B. Glass Speci¿ cations ............................4

C. Speci¿ cations ......................................4

D. High Altitude Installations ....................4

E. Non-Combustible Materials .................4

F. Combustible Materials ........................4

G. Requirements for the

Commonwealth of Massachusetts ......5

Section 2: Getting Started

A. Design & Installation

Considerations ....................................6

B. Tools and Supplies Needed................6

C. Inspect Appliance & Components .......6

Section 3: Appliance Location & Clearances

A. Selecting Appliance Location..............7

B. Clearances to Combustibles ...............7

Section 4: Termination Locations

A. Vent Termination Minimum

Clearances..........................................8

Section 5: Vent Information

A. Venting Components ..........................10

B. Use of Elbows .....................................10

C. Measuring Standards ..........................10

D. How to Use the Vent Graph ................11

E. Venting Guidelines ..............................11

F. Horizontal Termination ........................12

G. Vertical Termination ............................15

H. Slim Line Wall Thimble .......................23

Section 6: Gas Information

A. Fuel Conversions ................................25

B. Gas Pressures ....................................27

C. Gas Connection.. ................................27

Section 7: Electrical Information

A. Recommendation for Wire ..................29

B. Connecting to the Appliance ...............29

C. Standing Pilot Ignition System

Wiring ..................................................29

D. Ignition Module Access and

Battery Replacement ..........................30

Section 8: Appliance Setup

A. Remove Shipping Materials ................31

B. Leg Leveling System ...........................31

C. Flue Restrictor Installation ..................31

D. Intake Damper Operation ....................32

E. Intake Air Shutter Adjustment .............32

F. Positioning the Logs ............................32

G. Mineral Wool .......................................33

H. Accessories .........................................33

I. Blower Installation ...............................34

J. Glass Replacement .............................36

Section 9: Operating Instructions

A. Before Lighting Appliance ...................37

B. Controls ...............................................37

C. Lighting Appliance ...............................38

D. After Appliance is Lit ...........................39

E. Frequently Asked Questions ...............39

Section 10: Troubleshooting ...............................40

Section 11: Maintaining & Servicing Appliance

A. Maintenance Tasks .............................42

Section 12: Reference Materials

A. Appliance Dimension Diagram ...........44

B. Vent Components Diagram ................45

C. Vent Components List ........................46

D. Service Parts List ................................48

E. Limited Lifetime Warranty ...................52

F. Contact Information ............................54

Î= Contains updated information.

Heat & Glo • Tiara Petite B • 7026-101 Rev. Q • 10/13

4Heat & Glo • Tiara Petite B • 7026-101 Rev. Q • 10/13

1Listing and Code Approvals

The product is listed to ANSI standards for “Vented Gas

Appliance Heaters” and applicable sections of “Gas Burning

Heating Appliances for Manufactured Homes and Recre-

ational Vehicles” and "Gas Fired Appliances for use at High

Altitudes".

A. Appliance Certi¿ cation

B. Glass Speci¿ cations

NOTE: This installation must conform with local codes. In the

absence of local codes you must comply with the National

Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A.

and the CAN/CGA B149 Installation Codes in Canada.

D. High Altitude Installations

Omni-Test Laboratories, Inc. listed gas appliances are tested

and approved without requiring changes for elevations from

0 to 2000 feet in the U.S.A. and 0 to 4500 feet in Canada.

When installing this appliance at an elevation above 2000

feet, it may be necessary to decrease the input rating by

changing the existing burner ori¿ ce to a smaller size. Input

rate should be reduced by 4% for each 1000 feet above a

2000 foot elevation in the U.S.A. If the heating value of the

gas has been reduced, these rules do not apply. To identify

the proper ori¿ ce size, check with the local gas utility.

If installing this appliance at an elevation above 4500 feet (in

Canada), check with local authorities.

C. Speci¿ cations

This appliance is equipped with 5mm ceramic glass behind

the curved glass. Replace glass only with 5mm ceramic

glass. Please contact your dealer for replacement glass.

WARNING

Do NOT use this appliance if any part has been under water.

Immediately call a quali¿ ed service technician to inspect

the appliance and to replace any part of the control system

and any gas control which has been under water.

Manufactured Home or Mobile Home installation may occur

only after the home is site located and must conform with

the Manufactured Home Construction and Safety Standard,

Title 24 CFR, Part 3280, or, when such a standard is

not applicable, the Standard for Manufactured Home

Installations, ANSI/NCSBCS A225.1, or Standard for Gas

Equipped Recreational Vehicles and Mobile Housing, CSA

Z240.4.

When installed, the appliance must be electrically grounded

in accordance with local codes or, in the absence of local

codes, with the National Electrical Code, ANSI/NFPA 70, or

the Canadian Electrical Code, CSA C22.1.

*Maximum Vent Blower On

**Canada Only

MODEL Tiara Petite B

LABORATORY OMNI-Test Laboratories, Inc.

061-S-47b-5

TYPE Vented Gas Fireplace Heater

STANDARD ANSI Z21.88b-2003 ʘ CSA 2.33b-2003ʘ

UL307b ʘ CAN/CBA 2.17-M91

Model

(US or Canada)

Maxi-

mum

Input

BTU

Mini-

mum

Input

BTU

Ori¿ ce

Size

(DMS)

*Steady

State

Ef¿ -

ciency

**P.4

Tiara Petite B

(NG)

17,000 12,000 49 73.93 57.30

Tiara Petite B

(LP)

17,000 13,000 56 78.19 63.22

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a

Vertical Tube Furnace at 750°C, shall be considered non-

combustible materials.

Materials made of or surfaced with wood, compressed

paper, plant fibers, plastics, or other materials that can ignite

and burn, whether flame proofed or not, or whether plastered

or unplastered shall be considered combustible materials.

E. Non-Combustible Materials

F. Combustible Materials

5Heat & Glo • Tiara Petite B • 7026-101 Rev. Q • 10/13

NOTE: The following requirements reference various

Massachusetts and national codes not contained in this

document.

For all side wall horizontally vented gas fueled equipment

installed in every dwelling, building or structure used in whole

or in part for residential purposes, including those owned or

operated by the Commonwealth and where the side wall

exhaust vent termination is less than seven (7) feet above

¿ nished grade in the area of the venting, including but not

limited to decks and porches, the following requirements

shall be satis¿ ed:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented

gas fueled equipment, the installing plumber or gas ¿ tter shall

observe that a hard wired carbon monoxide detector with an

alarm and battery back-up is installed on the À oor level where

the gas equipment is to be installed. In addition, the installing

plumber or gas ¿ tter shall observe that a battery operated

or hard wired carbon monoxide detector with an alarm is

installed on each additional level of the dwelling, building or

structure served by the side wall horizontal vented gas fueled

equipment. It shall be the responsibility of the property owner

to secure the services of quali¿ ed licensed professionals for

the installation of hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fueled

equipment is installed in a crawl space or an attic, the hard

wired carbon monoxide detector with alarm and battery back-

up may be installed on the next adjacent À oor level.

In the event that the requirements of this subdivision can not

be met at the time of completion of installation, the owner shall

have a period of thirty (30) days to comply with the above

requirements; provided, however, that during said thirty (30)

day period, a battery operated carbon monoxide detector with

an alarm shall be installed.

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accordance

with the above provisions shall comply with NFPA 720 and

be ANSI/UL 2034 listed and IAS certi¿ ed.

Signage

A metal or plastic identi¿ cation plate shall be permanently

mounted to the exterior of the building at a minimum height

of eight (8) feet above grade directly in line with the exhaust

vent terminal for the horizontally vented gas fueled heating

appliance or equipment. The sign shall read, in print size no

less than one-half (1/2) inch in size, “GAS VENT DIRECTLY

BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS.”

G. Requirements for the Commonwealth of

Massachusetts

Inspection

The state or local gas inspector of the side wall horizontally

vented gas fueled equipment shall not approve the installa-

tion unless, upon inspection, the inspector observes carbon

monoxide detectors and signage installed in accordance with

the provisions of 248 CMR 5.08(2)(a) 1 through 4.

Exemptions

The following equipment is exempt from 248 CMR 5.08(2)

(a) 1 through 4:

•

The equipment listed in Chapter 10 entitled “Equipment

Not Required To Be Vented” in the most current edition of

NFPA 54 as adopted by the Board; and

Product Approved side wall horizontally vented gas fueled

equipment installed in a room or structure separated from

the dwelling, building or structure used in whole or in part

for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall

horizontally vented gas fueled equipment provides a vent-

ing system design or venting system components with the

equipment, the instructions provided by the manufacturer for

installation of the equipment and the venting system shall

include:

•

Detailed instructions for the installation of the venting sys-

tem design or the venting system components; and

A complete parts list for the venting system design or

venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall hor-

izontally vented gas fueled equipment does not provide the

parts for venting the À ue gases, but identi¿ es “special vent-

ing systems”, the following requirements shall be satis¿ ed by

the manufacturer:

•

The referenced “special venting system” instructions shall

be included with the appliance or equipment installation

instructions; and

The “special venting system” shall be Product Approved

by the Board, and the instructions for that system shall

include a parts list and detailed installation instructions.

A copy of all installation instructions for all Product Approved

side wall horizontally vented gas fueled equipment, all vent-

ing instructions, all parts lists for venting instructions, and/

or all venting design instructions shall remain with the appli-

ance or equipment at the completion of the installation.

See Gas Connection section for additional Common-

wealth of Massachusetts requirements.

6Heat & Glo • Tiara Petite B • 7026-101 Rev. Q • 10/13

2Getting Started

Check building codes prior to installation.

• Installation MUST comply with local, regional, state

and national codes and regulations.

• Consult local building, ¿ re of¿ cials or authorities having

jurisdiction about restrictions, installation inspection,

and permits.

CAUTION

. Design & Installation Considerations

B. Tools and Supplies Needed

C. Inspect Appliance & Components

Heat & Glo direct vent gas appliances are designed to oper-

ate with all combustion air drawn from outside of the building

and all exhaust gases expelled to the outside. No additional

air source is required.

When planning an installation, it is necessary to determine

the following information before installing:

• Where the appliance is to be installed.

•

The vent system con¿ guration to be used.

• Gas supply piping.

• Electrical wiring.

• Whether optional accessories - devices such as a blower,

thermostat or remote control - are desired.

Before beginning the installation be sure that the following

tools and building supplies are available. Note: Not all

tools will apply to every installation.

• Carefully remove the appliance and components from

the packaging.

• Remove cast door and glass door, and set aside on pro-

tective surface.

• Remove log set and component pack from ¿ rebox.

• Report to your dealer any parts damaged in shipment,

particularly the condition of the glass.

• Read all of the instructions before starting the instal-

lation. Follow these instructions carefully during the

installation to ensure maximum safety and bene¿ t.

Reciprocating saw Variable Speed Drill/Driver

Pliers Wrench Set

Hammer Framing Square

Phillips Screwdriver Framing Material

Flat Blade Screwdriver Voltmeter

Plumb Line Gloves

Level Safety Glasses

Manometer Tape Measure

Non-corrosive Leak Check Solution or combustible gas

detector

Caulking material (300ºF minimum continuous exposure

rating)

Keep appliance dry.

• Mold or rust may cause odors.

• Water may damage controls.

WARNING

• Installation and use of any damaged appliance or vent

system component.

• Modi¿ cation of the appliance or vent system.

• Installation other than as instructed by Hearth & Home

Technologies.

• Improper positioning of the gas logs or the glass door.

• Installation and/or use of any component part not approved

by Hearth & Home Technologies.

Any such action may cause a ¿ re hazard.

WARNING

Hearth & Home Technologies disclaims any

responsibility for, and the warranty will be

voided by, the following actions:

Inspect appliance and components for

damage. Damaged parts may impair safe

operation.

WARNING

• Do NOT install damaged components.

• Do NOT install incomplete components.

• Do NOT install substitute components.

Report damaged parts to dealer.

7Heat & Glo • Tiara Petite B • 7026-101 Rev. Q • 10/13

3Appliance Location and Clearances

A. Selecting Appliance Location

NOTE:

· Illustrations reÀ ect typical installations and are FOR

DESIGN PURPOSES ONLY.

· Illustrations/diagrams are not drawn to scale.

· Actual installation may vary due to individual design

preference.

When selecting a location for your appliance it is important

to consider the required clearances to wall (see Figure 3.1).

Figure 3.1

B. Clearances to Combustibles

Model AB C DE F G H

Tiara

Petite B

Inches 6 2 2 43 36 30 20-1/4 19-1/2

Millimeters 152 51 51 1092 914 762 527 495

"A" measurement is from

stove top, not side

G-Alcove

WARNING

Fire Risk

Provide adequate clearance:

• Around air openings

• To combustibles

• For service access

Locate appliance away from traf¿ c areas.

NOTE: For actual appliance dimensions refer to

Section 12.

Fire Risk.

• Locate and install appliance to all

clearance speci¿ cations in manual.

WARNING

NOTE: Flooring beneath appliance may reach 90 degrees

plus room ambient temperature. Check with flooring

manufacturer for maximum temperature allowed on flooring

surfaces.

It is permissable to place the appliance on carpet.

CAUTION

Some carpet materials may be sensitive to radiant heat from the

appliance causing discoloration or odor.

Fire Risk.

Odor Risk.

Tipping Risk

• Install appliance on a stable, level platform/

À oor strong enough to support appliance

without tipping.

• USE wood À ooring, ceramic tile, brick hearth

or high pressure laminate À ooring applied

directly over the sub-À ooring material.

WARNING

8Heat & Glo • Tiara Petite B • 7026-101 Rev. Q • 10/13

4Termination Locations

A. Vent Termination Minimum Clearances

Figure 4.2 Multiple Vertical Temination

Figure 4.1 Termination Clearances

Figure 4.3 speci¿ es minimum vent heights for various

pitched roofs.

Figure 4.3 Minimum Height from Roof to Lowest Discharge

HORIZONTAL

OVERHANG

VERTICAL

WALL

GAS DIRECT VENT

TERMINATION CAP

ROOF PITCH

IS X/ 12

LOWEST

DISCHARGE

OPENING

2 FT.

MIN.

20 INCHES MIN.

H (MIN.) - MINIMUM HEIGHT FROM ROOF

TO LOWEST DISCHARGE OPENING

Roof Pitch H (Min.) Ft.

Flat to 6/12 .........................................................1.0*

Over 6/12 to 7/12........................................................1.25*

Over 7/12 to 8/12 ............................................... 1.5*

Over 8/12 to 9/12 ............................................... 2.0*

Over 9/12 to 10/12 ............................................. 2.5*

Over 10/12 to 11/12 ........................................... 3.25

Over 11/12 to 12/12 ........................................... 4.0

Over 12/12 to 14/12 ........................................... 5.0

Over 14/12 to 16/12 ........................................... 6.0

Over 16/12 to 18/12 ........................................... 7.0

Over 18/12 to 20/12 ........................................... 7.5

Over 20/12 to 21/12 ........................................... 8.0

* 3 foot minimum in snow regions

Measure vertical clearances from this surface.

Measure horizontal clearances from this surface.

(See Figure 4.4 for speci¿ c clearances.)

Opening

Fire Risk.

Explosion Risk.

Maintain vent clearance to combustibles

as speci¿ ed.

WARNING

• Do not pack air space with insulation or

other materials.

Failure to keep insulation or other materials

away from vent pipe may cause ¿ re.

Gas, Wood or Fuel Oil

Termination Cap

Gas

Termination

Cap **

A *

*If using decorative cap cover(s), this distance may need to be

increased. Refer to the installation instructions supplied with the

decorative cap cover.

6 in. (minimum) up to 20 in.

152 mm/508 mm

18 in. minimum

457 mm

20 in. and over 0 in. minimum

In a staggered installation with both gas and wood or fuel oil

terminations, the wood or fuel oil termination cap must be

higher than the gas termination cap.

9Heat & Glo • Tiara Petite B • 7026-101 Rev. Q • 10/13

CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING,

IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE INSTALLED.

Figure 4.4

= VENT TERMINAL

= AIR SUPPLY INLET = AREA WHERE TERMINAL IS NOT PERMITTED

A = 12 inches ............. clearances above grade, veran-

da, porch, deck or balcony

B = 12 inches ............ clearances to window or door

that may be opened, or to per-

manently closed window. (Glass)

D* = 18 inches ............. vertical clearance to unventilat-

ed soffit or to ventilated soffit lo-

cated above the terminal

*30 inches ............ for vinyl clad soffits and below

electrical service

F = 9 inches .............. clearance to outside corner

G = 6 inches ............... clearance to inside corner

H = 3 ft. (Canada) ...... not to be installed above a gas

meter/regulatorassemblywithin 3

feet (90cm) horizontally from the

center-line of the regulator

I= 3 ft. ....................... clearance to gas service regula-

tor vent outlet

J = 9 inches (U.S.A.)

12 inches (Canada)clearance to non-mechanical air

supply inlet to building or the

combustion air inlet to any other

appliance

K = 3 ft. (U.S.A.)

6 ft. (Canada) ......... clearance to a mechanical

(powered) air supply inlet

L** = 7 ft. ......................... clearance above paved

sidewalkor a paved driveway

located on public property

M*** = 18 inches .............. clearance under veranda ,

porch, deck, balcony or over-

hang

42 inches .............. vinyl

** a vent shall not terminate directly above a sidewalk or paved

driveway which is located between two single family dwellings and

serves both dwellings.

*** only permitted if veranda, porch, deck or balcony is fully open on

a minimum of 2 sides beneath the floor, or meets Note 2.

(See Note 1)

S = 6 inches ................. clearance from sides of

electrical service

T = 12 inches ................ clearance above electrical

service

(See Note 3)

___________________________________________________________________

MIN

MAX

1cap 3feet 2xQ

ACTUA L

2 caps 6 feet 1 x Q

ACTUA L

3 caps 9 feet 2/3 x Q

ACTUA L

4caps 12feet 1/2xQ

ACTUA L

QMIN = # termination caps x 3 RMAX = (2 / # termination caps) xQACTUAL

N = 6 inches ................. non-vinyl sidewalls

12 inches ............... vinyl sidewalls

P=8ft.

Alcove Applications

NOTE 1: On private property where termination is less than 7 feet above

a sidewalk, driveway, deck, porch, veranda or balcony, use of a listed

cap is suggested. (See vents components pages.)

NOTE 2: Termination in an alcove space (spaces only open on one side

and

without

an overhang) are permitted with the dimensions specified for

vinyl or non-vinyl siding and soffits. 1. There must be at least 3 feet

minimum between termination caps. 2. All mechanical air intakes within

10 feet of a termination cap must be a minimum of 3 feet below the

termination cap. 3. All gravity air intakes within 3 feet of a termination cap

must be a minimum of 1 foot below the termination cap.

NOTE 3: Location of the vent termination must not interfere with access

NOTE: Local codes or regulations may require different

clearances.

NOTE: Termination caps may be hot. Consider their proximity to

doors or other traffic areas.

WARNING: In the U.S.: Vent system termination is NOT permitted

in screened porches. You must follow side wall, overhang and

ground clearances as slated in the instructions.

In Canada: Vent system termination is NOT permitted in screened

porches. Vent system termination is permitted in porch areas with

two or more sides open. You must follow side wall, overhang and

ground clearances as stated in the instructions.

Quadra-Fire assumes no responsibility for the improper perfor-

mance of the appliance when the venting system does not meet

these requirements.

(See Note 2)

Electrical

Service

J or K

U.S.

(3 FT)

10 Heat & Glo • Tiara Petite B • 7026-101 Rev. Q • 10/13

5Vent Information

A. Venting Components B. Use of Elbows

In order to comply with applicable codes and product

warranties, use only following venting components:

• Hearth & Home Technologies (HHT)

• Simpson Dura-Vent

• Selkirk Direct-Temp

• Amerivent Direct

• Security Secure Vent

DO NOT USE FIELD-FABRICATED VENTING

COMPONENTS. Refer to the venting manufacturer’s

instructions.

This product is approved to be vented either horizontally,

through the side wall or vertically through the roof. You may

vent through a Class A or masonry chimney if an approved

adapter is used.

This appliance is a direct vent heater. All combustion air must

come directly from the outside of the building. The vent pipe

for this unit consists of an inner and an outer pipe. The inner

pipe carries the appliance exhaust out of the system, and the

outer pipe brings fresh combustion air into the appliance.

Fire Hazard.

Explosion Risk.

Asphyxiation Risk.

Do NOT connect this gas appliance to a chimney

À ue serving a separate solid-fuel or gas burning

appliance.

• Vent this appliance directly outside.

• Use separate vent system for this appliance.

May impair safe operation of this appliance or

other appliances connected to the À ue.

WARNING

Diagonal runs have both vertical and horizontal vent aspects

when calculating the effects. Use the rise for the vertical

aspect and the run for the horizontal aspect. (See Figure 5.1.)

Two 45° elbows may be used in place of one 90° elbow. On

45° runs, one foot of diagonal is equal to 8-1/2 in. (216mm)

horizontal run and 8-1/2 in. (216mm) vertical run. A length of

straight pipe is allowed between two elbows. (See Figure 5.1.)

Vertical

Horizontal

12 in.

8-1/2 in.

Vertical and horizontal measurements were made using the

following standards.

C. Measuring Standards

CAUTION

ALL vent con¿ guration speci¿ cations MUST be followed.

• This product is tested and listed to these

speci¿ cations.

• Appliance performance will suffer if speci¿ cations are

not followed.

Figure 5.1

• Pipe measurements are from center line to center line.

• Horizontal terminations are measured to the outside of

the mounting surface (À ange of termination cap). See

Figure 4.1 on page 8.

• Vertical terminations are measured to the top of the last

pipe before termination cap.

• Horizontal pipe installed level with 1/4 in. rise.

•A round support box/wall thimble or heat shield is

required when the venting passes through a combus-

tible wall.

•A support box or ceiling ¿ restop is required when the

venting passes through a ceiling.

•Roof À ashing and a storm collar are required when

venting passes through the roof.

•Follow instructions provided with the venting for instal-

lation of these items.

11Heat & Glo • Tiara Petite B • 7026-101 Rev. Q • 10/13

25'

24'

22'

20'

18'

16'

14'

12'

10'

6 in. (152mm) Minimum starter pipe

30 in. (762mm) Maximum Horizontal run with no vertical pipe and with 1/4 in.

(6mm) rise per foot. Must use approved Termination Cap.

25 ft. (8m)

Maximum Vertical

2' 4' 6' 8' 10' 12' 14' 15'

Termination cap

Example 1

Example 2

Adjust

Intake

Damper

SLK-01TRD or an approved Termination Cap

6 ft. (2m) Minimum

Vertical Termination

VERTICAL DISTANCE

FROM APPLIANCE TO

90° ELBOW

Install Flue

Restrictor

Adjust

Intake

Damper

D. How to Use the Vent Graph E. Venting Guidelines

1. Measure the distance from the top of appliance to the

center of the 90° elbow. On the graph below, draw a

horizontal line from that measurement on the vertical

axis across until it intersects with the slanted line.

2. From the point of this intersection, draw a vertical line to

the bottom of the graph.

3. The point at which this line meets the bottom line of the

graph is the maximum length of the horizontal run.

Example 1: If the vertical dimension from the top of the

appliance to the center of the 90° elbow is 7 ft. (2m), the

horizontal run to the outer wall À ange must not exceed 9

ft.-8 in. (3m).

Example 2: If the vertical dimension from the top of the

appliance is 21 ft. (6m), the horizontal run to the outer wall

À ange must not exceed 4 ft.-3 in. (1m).

4. Each 90° elbow is equivalent to 3 ft. (914mm) of vent

pipe and each 45° elbow is equivalent to 1 ft. (305mm)

of vent pipe, and must be subtracted from vent pipe

run. A single vertical to horizontal 90° elbow is already

calculated into the allowable 15 ft. (5m) run. Each

additional 90° elbow reduces the maximum horizontal

distance by 3 ft. (914mm).

Example: The use of three elbows would reduce the

allowable horizontal run to 9 ft. (3 - 1 = 2 elbows

x 3 ft. = 6 ft.; 15 ft. max. - 6 ft. = 9 ft. max.)

Notes:

• The maximum horizontal vent run is 15 ft. (5m) when the

vertical vent rise is 10 ft. (3m).

• Horizontal sections require a 1/4 in. (6mm) rise for every

12 in. (305mm) of horizontal travel.

• Exterior vent diameter = 6-5/8 in. (168mm); Inner vent

diameter = 4 in. (102mm).

•

Horizontal sections require noncombustible support every

3 ft. (914mm) , e.g. wall straps.

• For any vertical termination a minimum of 6 ft. (2m)

vertical must be used.

EXCEPTIONS FOR HORIZONTAL INSTALLATIONS:

*The maximum horizontal vent run is 30 in. (762mm).

*The maximum horizontal vent run with a 45° elbow is

18 in. (457mm).

*No external minimum rise is required.

*The minimum horizontal vent run is 6 in. (152mm).

Figure 5.2

NOTE: In the Commonwealth of Mas-

sachusetts the word damper shall be

replaced with the words À ue restrictor.

12 Heat & Glo • Tiara Petite B • 7026-101 Rev. Q • 10/13

F. Horizontal Termination

Figure 5.3

Type A - Up & Out Installation

90° ELBOW

PIPE LENGTH

TERMINATION CAP

WALL THIMBLE

WALL THIMBLE COVER

CENTER LINE

WALL THIMBLE

45°

ELBOW

2 in. (51mm) CLEARANCE FROM

STOVE CORNER TO

COMBUSTILE WALL

2 in. (51mm) CLEARANCE FROM STOVE CORNER TO COMBUSTIBLE

WALL

TERMINATION CAP

CENTER LINE

16-5/8 in.

WALL THIMBLE

WALL THIMBLE COVER

(42 cm)

Type C - 45° Elbow in Corner Installation

Type B - Straight Out Installation

Female Locking Lugs

Male Locking Lugs

Step 1.

Determine the desired location of the appliance. Check to

ensure that wall studs or roof rafters are not in the way when

the venting system is attached. If this is the case, you may

want to adjust the location of the appliance.

Figure 5.4

Step 2.

Direct vent pipe is designed with a locking connection. To

connect the venting system to the appliance flue outlet, a

twist-lock adapter is built into the appliance at the factory.

Wall thickness may vary. Remember to include wall

thickness in minimum clearances when figuring venting

lengths for your installation needs.

Note: Female ends of direct vent pipe/elbows are

designed to slide straight onto the male ends of adjacent

pipes by orienting the pipe indentations so they match and

slide into the entry slots on the male ends, see Figure 5.4.

Push the pipe sections completely together, then twist-lock

one section clockwise approximately one-quarter turn, until

the two sections are fully locked. The female locking lugs

may not be visible from the outside. They may be located by

examining the inside of the female ends.

Fire Risk.

Explosion Risk.

Combustion Fume Risk.

Use vent run supports per installation instructions.

Connect vent sections per installation instructions.

• Maintain all clearances to combustibles.

• Do NOT allow vent to sag below connection

point to appliance.

• Maintain speci¿ ed slope (if required).

WARNING

Improper support may allow vent to sag or separate.

Fire Hazard.

Exhaust Fume Risk.

Impaired Performance of Appliance.

WARNING

• Ensure vent components are locked together correctly.

• Pipe may separate if not properly joined.

13Heat & Glo • Tiara Petite B • 7026-101 Rev. Q • 10/13

NOTE:

(1) Installation requires a minimum of 6 in. (152mm)

horizontal run of vent with a 1/4 in. (6mm) rise run towards

the termination. Each 1 ft. (305mm) of horizontal venting

must include a 1/4 in. (6mm) rise. Never allow the vent

to run downward. This could cause high temperatures

and may present the possibility of a fire.

(2) The location of the horizontal vent termination on an

exterior wall must meet all local and national building

codes, and must not be easily blocked or obstructed,

see Figure 4.4 on page 9.

(3) For installations requiring a vertical rise on the exterior

of the building, a snorkel kit is available with a 14 in.

(356mm) and a 36 in. (914mm) tall snorkel termination

cap. Follow the same installation procedures as used

for standard horizontal terminations. If the snorkel

termination must be installed below grade (i.e. basement

application), proper drainage must be provided to

prevent water from entering the snorkel termination. Do

not backfill around snorkel termination.

HOT

WOOD

SCREW

WALL THIMBLE

NOTES:

(1) The four wood screws provided should be replaced with

appropriate fasteners for stucco, brick, concrete, or

other types of sidings.

(2) A termination cap with a built-in vinyl siding standoff is

highly recommended on a building with vinyl siding. The

pilot hole will be 2 in. (51mm) closer to the bottom of the

square than the top. Using a framing square, draw a 14

in. x 14 in. (356mm x 356mm) square around the pilot

hole in the siding. See Figure 5.7.

8 in.

(203mm)

7 in.

(178mm)

7 in.

(178mm) 6 in.

(152mm)

Figure 5.6

Figure 5.7

Figure 5.5

CENTER

LINE

CENTER LINE

CENTER OF

HOLE

WALL

THIMBLE

Step 4.

Position the horizontal termination cap in the center of the 10

in. x 10 in. (254mm x 254mm) square hole and run a bead

of non-hardening mastic around its outside edges, so as to

make a seal between it and the wall, attach termination cap

to the exterior wall with the four wood screws provided. The

arrow on the vent cap should be pointing up (Figure 5.6).

Step 3.

For installations using a round support box/wall thimble

(check pipe manufacturer's instructions), mark the wall for a

10 in. x 10 in. (254mm x 254mm) square hole. The center

of the square hole should line up with the center line of the

horizontal pipe, as shown in Figure 5.5. Cut and frame the

hole in the exterior wall where the vent will be terminated. If

the wall being penetrated is constructed of noncombustible

material, i.e. masonry block or concrete, a 7 in. (178mm)

diameter hole is acceptable.

14 Heat & Glo • Tiara Petite B • 7026-101 Rev. Q • 10/13

Step 5.

Place the wall thimble cover over the pipe assembly and

slide the appliance and vent assembly towards the wall,

carefully inserting the vent pipe into the vent termination

cap assembly. It is important that the vent pipe extend into

the vent termination cap a sufficient distance so as to result

in a minimum pipe overlap of 1-1/4 in. (32mm). Secure the

connection between the vent pipe and the vent termination

cap by attaching the two sheet metal strips extending from

the vent termination cap assembly into the outer wall of

the vent pipe. Use the two sheet metal screws provided to

connect the strips to the pipe section (Figure 5.9).

Fold Strap Here

Wall Thimble Cover/Ceiling

Firestop as Required by Local

Jurisdiction

1/4 in. (6mm)

Strap

Sheet Metal Screw

Wall Thimble

Figure 5.9

Burn Risk.

• Local codes may require installation of a cap

shield to prevent anything or anyone from

touching the hot cap.

WARNING

Do NOT connect a pipe section to a termination cap without

using the telescoping À ue section found on the termination cap.

WALL THIMBLE COVER

WALL THIMBLE

Vinyl siding standoff with siding beneath

removed

SCREWS

Bolt horizontal top to vinyl

standoff

SCREWS

Apply sealant to all four sides

VINYL SIDING

Figure 5.8

(NOTE: Some termination caps may cause the vent

pipe to be off center on flashing). Ensure that proper

clearances to combustible materials are maintained.

If you are not using an approved termination cap with

a built-in standoff on a building with vinyl siding, a

vinyl siding standoff should be installed between the

termination cap and the exterior wall (Figure 5.8).

Follow manufacturer’s instructions for attaching the

vinyl siding standoff to the horizontal termination cap.

The vinyl siding standoff prevents excessive heat from

possibly melting the vinyl siding material. The vent

terminal cap shall not be recessed into a wall or siding.

Remove siding from the area where the standoff will be

located.

Fire Hazard.

Exhaust Fume Risk.

Impaired Performance of Appliance.

WARNING

• Ensure vent components are locked together correctly.

• Pipe may separate if not properly joined.

Note: The attachment from the vent pipe to the vent

termination cap must be sealed with silicone. Termination

caps shall not be recessed into a wall or siding.

15Heat & Glo • Tiara Petite B • 7026-101 Rev. Q • 10/13

Step 1.

Check the installation instructions for required 1 in. (25mm)

clearances (air space) to combustibles when passing

through ceilings, walls, roofs, enclosures, attic rafters, or

other nearby combustible surfaces. See page 17, Figure

5.16. Check the instructions below for maximum vertical rise

of the venting system, and any maximum horizontal offset

limitations. All offsets must fall within the set parameters of

the vent graph (Figure 5.2) located on page 11.

NOTE: Maximum vertical rise allowable is 25 ft. (8m),

Figure 5.11.

NOTE: Maximum number of 45° elbows permitted for a

vertical installation is eight, provided their installation

does not decrease maximum allowable horizontal run (as

specified by vent graph, on page 11).

Plumber’s Tape

connected to

Wall Strap

7ZRÛ(OERZV

Step 2.

Set the gas appliance in its desired location. Drop a plumb

bob down from the ceiling to the position of the appliance

flue exit, and mark the location where the vent will penetrate

the ceiling. Drill a small hole at this point. Next, drop a plumb

bob from the roof to the hole previously drilled in the ceiling,

and mark the spot where the vent will penetrate the roof.

Determine if ceiling joists, roof rafters, or other framing will

obstruct the venting system. You may wish to relocate the

appliance, or to offset, as shown in Figure 5.12 to avoid

cutting loadbearing members.

G. Vertical Termination

1. Direct Vent Pipe

Figure 5.10

Figure 5.11

Figure 5.12

VERTICAL

TERMINATION

CAP

STORM

COLLAR

FLASHING

FIRESTOP

PIPE LENGTH

SUPPORT BOX

25 ft. (8m)

MAXIMUM

Fire Risk.

Explosion Risk.

Maintain vent clearance to combustibles as speci-

¿ ed.

WARNING

• Do not pack air space with insulation or other

materials.

Failure to keep insulation or other materials away

from vent pipe may cause ¿ re.

16 Heat & Glo • Tiara Petite B • 7026-101 Rev. Q • 10/13

Step 4.

Assemble the desired lengths of pipe and elbows necessary

to reach from the appliance up through the round support

box. Ensure that all pipe and elbow connections are in their

fully twist-locked position. Assemble as instructed.

Step 5.

Cut a hole in the roof centered on the small drill hole placed in

the roof in Step 2. The hole should be of sufficient size to meet

the minimum requirements for clearance to combustibles, as

specified. Continue to assemble lengths of pipe and elbows

necessary to reach from the ceiling support box/wall thimble

up through the roof line. Galvanized pipe and elbows may

be utilized in the attic, as well as above the roofline. The

galvanized finish is desirable above the roofline, due to its

higher corrosion resistance.

NOTE:

(1) If an offset is necessary in the attic to avoid obstructions,

it is important to support the vent pipe every 3 ft.

(914mm) to avoid excessive stress on the elbows, and

possible separation. Wall straps are available for this

purpose, Figure 5.12, page 15.

(2) Whenever possible, use 45° elbows, instead of 90°

elbows. The 45° elbow offers less restriction to the flow

of flue gases and intake air.

Step 7.

Continue to assemble pipe sections until the height of the

vent (before adding the termination cap) meets the minimum

code requirements as outlined in the current CAN/CGA-

B149 Installation Codes (in Canada), the National Fuel

Gas Code NFPA 54/ANSI Z223.1 (in USA), or local codes.

Note that for steep roof pitches, the vent height must be

increased. See roof pitch table (Figure 4.3, on page 8). In

high wind conditions, nearby trees adjoining rooflines, steep

pitched roofs, and other similar factors can result in poor

draft, or down drafting. In these cases increasing the vent

height or switching to the high wind termination cap may

solve this problem.

Step 3.

To install the round support box/wall thimble cover in a flat

ceiling, cut a 10 in. (254mm) square hole in the ceiling,

centered on the hole drilled in Step 2. Frame the hole as

shown in Figure 5.13.

Framing

1 - 1/2 in. (38mm) Long

Wood Screws

Ceiling

Joists

Figure 5.13

Shingles overlap on

top edge of flashing

CAP AND STORM

COLLAR NOT SHOWN

FOR CLARITY

Figure 5.14

Step 8.

Slip the storm collar over the pipe, and push it down to the

top of the flashing (Figure 5.15). Use non-hardening sealant

above and below the joint between the storm collar and the

pipe.

Step 6.

Slip the flashing over the pipe section(s) protruding through

the roof. Secure the base of the flashing to the roof with

roofing nails. Ensure the roofing material overlaps the top

edge of the flashing as shown in Figure 5.14. Verify that the

chimney is the required height above the roof. See roof pitch

table, Figure 4.3, on page 8.

Optional High Wind Termination Cap

Secure Flashing with Non-Hardening

Sealant and Roofing Nails

Figure 5.15

17Heat & Glo • Tiara Petite B • 7026-101 Rev. Q • 10/13

MIN. 1 in. (25mm)

CLEARANCE

CEILING FIRES TOP

NAILS

MIN. 1 in. (25mm)

CLEARANCE

MIN. 1 in. (25mm)

CLEARANCE

MIN. 1 in. (25mm)

CLEARANCE

Figure 5.16

Fire Risk.

Explosion Risk.

WARNING

• Any occupied areas above the first floor, including

closets and storage spaces, which the vertical

vent passed through must be enclosed. The

enclosure may be framed and sheetrocked with

standard construction materials; however, refer

to these installation instructions for the minimum

allowable clearance between the outside of the

vent pipe and the combustible surfaces of the

enclosure. Do not fill any of the required air space

with insulation.

Step 9.

Twist-lock the vent cap and seal.

Note: For multi-story vertical installations, a ceiling firestop

is required at the second floor, and any subsequent floors

(Figure 5.16). The opening should be framed to 10 in. x

10 in. (254mm x 254mm) inside dimensions, in the same

manner as shown in Figure 5.13 on page 16.

18 Heat & Glo • Tiara Petite B • 7026-101 Rev. Q • 10/13

2. Cathedral Ceiling

Level

Cathedral Ceiling

Support Box

2 in. (51mm)

Min. below

finished ceiling

Cut hole 1/8 in. (3mm)

greater in size than

pattern of support box

as it is projected onto

roof line

Figure 5.17

Figure 5.18

Step 1.

Follow installation Steps 1 and 2 under vertical installation

section, page 15.

Step 2.

Remove shingles or other roof covering as necessary to cut

the rectangular hole for the support box. Cut the hole 1/8 in.

(3mm) larger than the support box outline.

Step 3.

Lower the support box through the hole in the roof until the

bottom of the support box protrudes at least 2 in. (51mm)

below the ceiling (Figure 5.17). Align the support box both

vertically and horizontally with a level. Temporarily tack the

support box in place through the inside walls and into the

roof sheathing.

Step 4.

Using tin snips, cut the support box from the top corners

down to the roofline, and fold the resulting flaps over the

roof sheathing (Figure 5.18). Before nailing it to the roof,

run a bead of non-hardening mastic around the top edges

of the support box to make a seal between it and the roof.

Clean out any combustible material from inside the support

box.

Step 7.

Complete the cathedral ceiling installation by following the

same procedures outlined in steps 7 through 9 for vertical

installations, pages 16-17.

Step 6.

Place the support clamp (provided with the support box)

inside the support box (at the bottom), and secure to the pipe

section. The clamp allows the support box to support the

weight of the pipe sections. Continue to add pipe sections

until you are above the roofline.

Cathedral

Ceiling

Trim Collar

Screws

Support

Box

Step 8.

Install the black trim collar around the outside of the cathedral

ceiling support box (Figure 5.19). The two pieces of the trim

collar slide over one another to allow for easy adjustment

around the support box. Using the six screws provided,

secure the four corners and the overlapping sections of the

trim collar to the ceiling. You may want to predrill the holes for

the overlapped sections for ease of installation.

Figure 5.19

Step 5.

Assemble the desired lengths of pipe and elbows necessary

to reach from the appliance up through the round support

box. Ensure that all pipe and elbow connections are in their

fully twist-locked position. Assemble as instructed.

19Heat & Glo • Tiara Petite B • 7026-101 Rev. Q • 10/13

3. Class A Metal Chimney

Figure 5.20

TERMINATION

CAP

EXISTING

METAL

CHIMNEY

SYSTEM

TOP

ADAPTOR

FLASHING

4 in. (102mm)

FLEX PIPE

RETRO CONNECTOR

DIRECT VENT PIPE

High Wind Termination

Cap

Sheet Metal Screws

Drill Four 1/8 in.

(3mm) Diameter

Holes

Figure 5.22

Figure 5.23

Step 4.

Pass the flex pipe down through the center of the chimney

system, and center the top adapter on the top of the chimney

pipe. Drill four 1/8 in. (3mm) diameter holes through the

top adapter, and into the chimney top. Ensure that you are

drilling into the metal on the chimney. Twist lock the high

wind termination cap onto the top adapter (Figures 5.22

and 5.23).

Step 5.

Pull the flex pipe down through the ceiling support box, until

it protrudes approximately 3 in. (76mm). Connect the flex

pipe to the retro connector, and attach with sheet metal

screws.

Step 6.

Push the flex pipe back up into the ceiling support box,

center the retro connector, and attach it to the support box

with sheet metal screws.

Step 7.

The connection between the appliance and the retro

connector may be completed with sections of direct vent

pipe.

Top Adapter

Sheet Metal Screws

Flex Pipe

Figure 5.21

Step 1.

Remove existing chimney cap.

Step 2.

Measure the distance from the top of the chimney to the

bottom of the ceiling support box, add 3 in. (76mm) to this

measurement, and cut a section of 4 in. (101mm) flex pipe to

that length (the flex should be fully extended).

Step 3.

Connect the end of the flex pipe section to the underside of

the top adapter, using four sheet metal screws (Figure 5.21).

CAUTION

Ensure that existing chimney is functionally sound and clean.

• Have inspection done by qualified chimney sweep or

professional installer BEFORE converting to direct vent

appliance.

20 Heat & Glo • Tiara Petite B • 7026-101 Rev. Q • 10/13

4. Existing Masonry Chimney

Type C - Up & Out Installation Type D - Hearth Mount

Figure 5.24

CHIMNEY LINER

TERMINATION

CAP

3 in. (76mm)

FLEX LINER

SHOWING TWO

25 ft. (8m)

SECTIONS OF

FLEX LINER

CO-AXIAL TO

CO-LINEAR

CONNECTOR

PIPE LENGTH

OPTIONAL

CHIMNEY LINER

TERMINATION CAP

25 ft. (8m) OF 3 in.

(76mm) FLEX LINER

THIS SECTION OF THE

CHIMNEY MUST BE

SEALED

CHIMNEY MUST BE SEALED

FROM 4 ft. (1m) SECTION TO

TERMINIATION USING A

SMOKE SHELF OR A

DAMPER*. SEAL SHOULD BE

6 in. (152mm) BELOW END OF

4 ft. (1m) AIR INTAKE

SECTION.

CO-AXIAL TO CO-LINEAR

CONNECTOR

4 ft. (1m) OF 3 in. (76mm)

FLEX LINER AIR INTAKE

SECTION

ALCOVE CLEARANCE

TO COMBUSTIBLES

MUST BE MAINTAINED.

CHIMNEY LINER

TERMINATION CAP

25 ft. (8m) OF 3 in.

(76mm) FLEX

LINER EXHAUST

SECTION

THIS SECTION OF

THE CHIMNEY MUST

BE SEALED

THE CHIMNEY MUST BE

SEALED FROM THE 4 ft. (1m)

SECTION TO TERMINATION

USING A SMOKE SHELF OR A

DAMPER. THE SEAL SHOULD

BE 6 in. (152mm) BELOW THE

END OF THE 4 ft. (1m) AIR

INTAKE SECTION.

4 ft. (1m) OF 3 in.

(152mm) FLEX LINER

AIR INTAKE SECTION

CO-AXIAL TO

CO-LINEAR

CONNECTOR

PIPE LENGTH

OPTIONAL

TERMINATION

CAP

FLASHING

4 in. (1m) FLEX

LINER

TOP ADAPTOR

RETRO

CONNECTOR

90 DEGREE

ELBOW

DIRECT

VENT PIPE

Type A & B Co-Axial to Co-Linear

*In the Commonwealth of Massachusetts, the word damper

shall be replaced with the words flue restrictor.

La page charge ...

Heat & Glo Tiara Petite-B TiaraP Install Manual

Marque: Heat & Glo

Modèle: Tiara Petite-B TiaraP

Catégorie: Cheminées

Taper: Install Manual

Télécharger le PDF

rapport

dans d''autres langues

English: Heat & Glo Tiara Petite-B TiaraP

Heat & Glo Tiara Petite-B TiaraP Install Manual

Heat & Glo Tiara Petite-B TiaraP Install Manual

dans d''autres langues

Documents connexes

Autres documents