MTD L-Style Manuel utilisateur

Catégorie
Souffleuses à neige
Taper
Manuel utilisateur
Safety • Assembly • Operation • Adjustments • Maintenance • Troubleshooting • Parts Lists •
MTD Products Ltd., P. O. Box 1386, KITCHENER, ONTARIO N2G 4J1
PRINTED IN U.S.A.
IMPORTANT:
READ SAFETY RULES AND INSTRUCTIONS
CAREFULLY BEFORE OPERATING EQUIPMENT.
OPERATOR’S MANUAL
Two-Stage Snow Thrower
769-03242
07/23/07
2
Finding and Recording Model Number
Table of Contents
BEFORE YOU START ASSEMBLING
YOUR NEW EQUIPMENT,
please locate the model plate on the equipment and copy the
model number and the serial number to the sample model
plate provided to the right. You can locate the model plate by
standing at the operating position and looking down at the
frame.
This Operator’s Manual is an important part of your new snow thrower. It will help you assemble,
prepare and maintain the unit for best performance. Please read and understand what it says.
-4$02/$5#43,)-)4%$
+)4#(%.%2/..'*

8888888888
88888888888
-ODEL.UMBER
.UM£RODEMODÞLE
3ERIAL.UMBER
.UM£RODES£RIE
WWWMTDCANADACOM
Please do
NOT
return the unit to the retailer from which it was purchased,
without first contacting Customer Support.
Customer Support
If you have difficulty assembling this product or have any questions regarding the controls, operation or maintenance of this unit,
you can seek help from the experts. Choose from the options below:
1. Visit www.mtdcanada.ca for many useful suggestions, click on Customer Support button.
2. Call a Customer Support Representative at 1-800-668-1238.
3. The engine manufacturer is responsible for all engine-related issues in terms of performance, power-rating, specifications,
warranty, and service. Depending on the engine manufacturer, more information is included in this publication or packed
separately with this product.
Please have your unit’s model number and serial number ready when you call. See previous section to locate this information.
You will be asked to enter the serial number in order to process your call.
Safety Labels ...................................................... 3
Safe Operation Practices ................................... 4
Setting Up Your Snow Thrower .......................... 6
Know Your Snow Thrower .................................. 8
Operating Your Snow Thrower ........................... 9
Adjustments & Maintenance ........................... 12
Off-Season Storage .......................................... 14
Trouble Shooting .............................................. 15
Illustrated Parts Lists ....................................... 16
Warranty ............................................................ 20
3
1
Safety
Labels
WARNING
This symbol points
out important safety
instructions which,
if not followed, could
endanger the per-
sonal safety and/or
property of yourself
and others. Read and
follow all instructions
in this manual before
attempting to operate
this machine. Failure
to comply with these
instructions may
result in personal
injury. When you see
this symbol, HEED
ITS WARNING!
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
and follow the warnings
and instructions
in this manual
and on the machine.
A chute clean-out tool is fastened to the top
of the auger housing with a mounting clip. The
tool is designed to clear a chute assembly of
ice and snow.
This item is fastened with a cable tie at the
factory. Cut the cable tie before operating the
snow thrower.
WARNING: Never use your
hands to clear a clogged chute
assembly. Shut off engine and
remain behind handles until
all moving parts have stopped
before using the clean-out tool
to clear the chute assembly.
#3
Chute Clean-out
Tool
4
2
Safe
Operation
Practices
Training
1. Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place for
future and regular reference and for ordering replacement
parts.
2. Be familiar with all controls and their proper operation.
Know how to stop the machine and disengage them quickly.
3. Never allow children under 14 years old to operate this
machine. Children 14 years old and over should read and
understand the instructions and safe operation practices
in this manual and on the machine and be trained and
supervised by an adult.
4. Never allow adults to operate this machine without proper
instruction.
5. Thrown objects can cause serious personal injury. Plan
your snow-throwing pattern to avoid discharge of material
toward roads, bystanders and the like.
6. Keep bystanders, helpers, pets and children at least 75 feet
from the machine while it is in operation. Stop machine if
anyone enters the area.
7. Exercise caution to avoid slipping or falling, especially
when operating in reverse.
Preparation
1. Thoroughly inspect the area where the equipment is to be
used. Remove all doormats, newspapers, sleds, boards,
wires and other foreign objects, which could be tripped
over or thrown by the auger/impeller.
2. Always wear safety glasses or eye shields during
operation and while performing an adjustment or repair
to protect your eyes. Thrown objects which ricochet can
cause serious injury to the eyes.
3. Do not operate without wearing adequate winter outer gar
-
ments. Do not wear jewelry, long scarves or other loose
clothing, which could become entangled in moving parts.
Wear footwear which will improve footing on slippery
surfaces.
4. Use a grounded three-wire extension cord and receptacle
for all units with electric start engines.
5. Adjust collector housing height to clear gravel or crushed
rock surfaces.
6. Disengage all control levers before starting the engine.
7. Never attempt to make any adjustments while engine is
running, except where specifically recommended in the
operator’s manual.
8. Let engine and machine adjust to outdoor temperature
before starting to clear snow.
Safe Handling of Gasoline
To avoid personal injury or property damage use extreme care
in handling gasoline. Gasoline is extremely flammable and the
vapors are explosive. Serious personal injury can occur when
gasoline is spilled on yourself or your clothes, which can ignite.
Wash your skin and change clothes immediately.
a. Use only an approved gasoline container.
b. Extinguish all cigarettes, cigars, pipes and other sources
of ignition.
c. Never fuel machine indoors.
d. Never remove gas cap or add fuel while the engine is hot
or running.
e. Allow engine to cool at least two minutes before refuel
-
ing.
f. Never over fill fuel tank. Fill tank to no more than ½ inch
below bottom of filler neck to provide space for fuel
expansion.
g. Replace gasoline cap and tighten securely.
h. If gasoline is spilled, wipe it off the engine and equip
-
ment. Move machine to another area. Wait 5 minutes
before starting the engine.
i. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light (e.g. furnace,
water heater, space heater, clothes dryer etc.).
j. Allow machine to cool at least 5 minutes before storing.
WARNING: Engine Exhaust, some of its constituents, and certain vehicle compo-
nents contain or emit chemicals known to State of California to cause cancer and
birth defects or other reproductive harm.
WARNING
This symbol points
out important safety
instructions which,
if not followed, could
endanger the per-
sonal safety and/or
property of yourself
and others. Read and
follow all instructions
in this manual before
attempting to operate
this machine. Failure
to comply with these
instructions may
result in personal
injury. When you see
this symbol, HEED
ITS WARNING!
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
and follow the warnings
and instructions
in this manual
and on the machine.
DANGER: This machine was built to be operated according to the safe operation practices in this
manual. As with any type of power equipment, carelessness or error on the part of the operator can
result in serious injury. This machine is capable of amputating hands and feet and throwing objects.
Failure to observe the following safety instructions could result in serious injury or death.
5
Operation
1. Do not put hands or feet near rotating parts, in the
auger/impeller housing or chute assembly. Contact with the
rotating parts can amputate hands and feet.
2. The auger/impeller control lever is a safety device. Never
bypass its operation. Doing so makes the machine unsafe
and may cause personal injury.
3. The control levers must operate easily in both directions
and automatically return to the disengaged position when
released.
4. Never operate with a missing or damaged chute assembly.
Keep all safety devices in place and working.
5. Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless and
deadly gas.
6. Do not operate machine while under the influence of alcohol
or drugs.
7. Muffler and engine become hot and can cause a burn. Do
not touch.
8. Exercise extreme caution when operating on or crossing
gravel surfaces. Stay alert for hidden hazards or traffic.
9. Exercise caution when changing direction and while operat
-
ing on slopes.
10. Plan your snow-throwing pattern to avoid discharge towards
windows, walls, cars etc. Thus, avoiding possible property
damage or personal injury caused by a ricochet.
11. Never direct discharge at children, bystanders and pets or
allow anyone in front of the machine.
12. Do not overload machine capacity by attempting to clear
snow at too fast of a rate.
13. Never operate this machine without good visibility or light.
Always be sure of your footing and keep a firm hold on the
handles. Walk, never run.
14. Disengage power to the auger/impeller when transporting or
not in use.
15. Never operate machine at high transport speeds on slippery
surfaces. Look down and behind and use care when
backing up.
16. If the machine should start to vibrate abnormally, stop the
engine, disconnect the spark plug wire and ground it against
the engine. Inspect thoroughly for damage. Repair any
damage before starting and operating.
17. Disengage all control levers and stop engine before you
leave the operating position (behind the handles). Wait
until the auger/impeller comes to a complete stop before
unclogging the chute assembly, making any adjustments, or
inspections.
18. Never put your hand in the discharge or collector openings.
Always use the clean-out tool provided to unclog the dis-
charge opening. Do not unclog chute assembly while engine
is running. Shut off engine and remain behind handles until
all moving parts have stopped before unclogging.
19. Use only attachments and accessories approved by the
manufacturer (e.g. wheel weights, tire chains, cabs etc.).
20. If situations occur which are not covered in this manual, use
care and good judgment. Call customer assistance for the
name of your nearest servicing dealer.
Maintenance & Storage
1. Never tamper with safety devices. Check their proper
operation regularly. Refer to the maintenance and adjust-
ment sections of this manual.
2. Before cleaning, repairing, or inspecting machine disengage
all control levers and stop the engine. Wait until the
auger/impeller come to a complete stop. Disconnect the
spark plug wire and ground against the engine to prevent
unintended starting.
3. Check bolts and screws for proper tightness at frequent
intervals to keep the machine in safe working condition.
Also, visually inspect machine for any damage.
4. Do not change the engine governor setting or over-speed
the engine. The governor controls the maximum safe
operating speed of the engine.
5. Snow thrower shave plates and skid shoes are subject to
wear and damage. For your safety protection, frequently
check all components and replace with original equipment
manufacturer’s (OEM) parts only. “Use of parts which do
not meet the original equipment specifications may lead to
improper performance and compromise safety!
6. Check controls periodically to verify they engage and
disengage properly and adjust, if necessary. Refer to the
adjustment section in this operator’s manual for instructions.
7. Maintain or replace safety and instruction labels, as neces
-
sary.
8. Observe proper disposal laws and regulations for gas, oil,
etc. to protect the environment.
9. Prior to storing, run machine a few minutes to clear snow
from machine and prevent freeze up of auger/impeller.
10. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light such as a water
heater, furnace, clothes dryer etc.
11. Always refer to the operator’s manual for proper instructions
on off-season storage.
Do not modify engine
To avoid serious injury or death, do not modify engine in any
way. Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.
Notice regarding Emissions
Engines which are certified to comply with California and federal
EPA emission regulations for SORE (Small Off Road Equipment)
are certified to operate on regular unleaded gasoline, and may
include the following emission control systems: Engine Modifica-
tion (EM) and Three Way Catalyst (TWC) if so equipped.
Average Useful Life
According to the Consumer Products Safety Commission
(CPSC) and the U.S. Environmental Protection Agency (EPA),
this product has an Average Useful Life of seven (7) years, or
60 hours of operation. At the end of the Average Useful Life,
buy a new machine or have the machine inspected annually by
an authorized service dealer to ensure that all mechanical and
safety systems are working properly and not worn excessively.
Failure to do so can result in accidents, injuries or death.
2
Safe
Operation
Practices
WARNING
This symbol points
out important safety
instructions, which
if not followed, could
endanger the per-
sonal safety and/or
property of yourself
and others. Read and
follow all instructions
in this manual before
attempting to operate
this machine. Failure
to comply with these
instructions may
result in personal
injury. When you see
this symbol, HEED
IT’S WARNING!
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
and follow the warnings
and instructions
in this manual
and on the machine.
6
3
Always stop engine,
disconnect spark
plug, and ground
against engine before
cleaning, lubricating
or doing any kind
of maintenance or
adjustments on your
machine.
DO NOT LIFT
MACHINE WITH
CHUTE HANDLE.
NOTE: Never replace
the auger shear pins
with standard pins.
Any damage to the
auger gearbox or other
components, as a reult
of doing so, will NOT
be covered by your
snow thrower’s war-
ranty.
Never use your hands
to clean snow and
ice from the chute
assembly or auger
housing..
IMPORTANT: This unit is shipped WITH OIL and
WITHOUT GASOLINE. After assembly refer to
separate engine manual for proper fuel and engine oil
recommendations.
NOTE: Reference to right hand or left hand side of
machine are observed from the operating position.
NOTE: This Operators Manual covers several models.
Snow thrower features vary by model. Not all features
discussed in this manual are applicable to all snow
thrower models.
Before Assembly
WARNING: Disconnect the spark plug
wire and Ground it against the engine
to prevent unintended starting.
1. Cut the cable tie that secures the upper handle to
the chute assembly for shipping purposes.
Setting Up The Handle
1. Loosen the chute knob on the upper chute(1) and
pivot the upper chute upwards(2) as far as it will go.
See Figure 1.
WARNING: Do not lift the snow thrower by the chute
handle.
2. Loosen the handle knob and handle tab on each
side of the handle. See Figure 2.
3.
Hold both controls against upper handle and pull
up as shown in Figure 3. Make sure that the upper
handle locks over the lower handle and handle tabs
align with the handle. You may have to carefully
maneuver the upper handle to clear chute assembly.
CAUTION: Be careful not to bend or kink the cable.
4. Tighten the handle knobs on each side of the
handle. Refer to step 2 in Figure 3.
5. Adjust upper chute and rotate chute handle to
desired operating position.
6. Tighten the chute knob on the upper chute making
sure the flat washer and the carriage bolt are
correctly positioned. Refer to Figure 1.
Clean-Out Tool
This tool and the electric extension cord, if so equipped,
may be fastened with a cable tie to the rear of the auger
housing for shipping purposes. In that case, cut the
cable tie and remove the extension cord now.
Final Adjustments
IMPORTANT: Check the adjustments as instructed and
make any final adjustments necessary before operating
the unit. Check all nuts and bolts for tightness.Failure to
follow these instructions may cause damage to unit.
Setup And
Adjustment
Figure 1
WARNING
Figure 3
Figure 2
1
2
1
7
3
Setting Up
Your Snow
Thrower
Tire Pressure
The proper inflation pressure is 20 psi. Check the tire
pressure periodically and maintain equal pressure in both
tires at all times. Excessive pressure (well above 20 psi)
may cause the wheel (tire/rim) assembly to burst with
sufficient force to cause serious injury. Do not over-inflate
the tire. Use a manual pump or portable electric tire
inflator to prevent over-inflation. NEVER USE AN AIR
COMPRESSOR.
Skid Shoe
The space between the shave plate and the ground
can be adjusted. See Figure 7. For close snow removal,
place skid shoes in the low position. When the area to
be cleared is uneven, place skid shoes in the middle or
high position. See Figure 4.
1. Adjust skid shoes by loosening two hex nuts and
carriage bolts on each skid shoe, and moving the
skid shoe to the desired position. See Figure 4.
2. Make certain the entire bottom surface of skid shoe
is against the ground to avoid uneven wear on the
skid shoes.
3. Tighten nuts and bolts securely.
Routing The Drive Cable
1. Make sure that the drive cable is routed parallel to
the left upper handle, then across the top of the
lower handle and finally parallel to the right lower
handle. See Figure 5.
2. Three cable ties have been used to loosely tie the
two control cables to the lower handle. Two of these
cable ties are on each arm, and third on the top
cross bar of the lower handle. Tighten these cable
ties to secure the cable to the lower handle. See
Figure 5.
Auger Cable
Periodic adjustment to the auger control cable may be
required due to normal stretch and wear on the belt.
Adjustment is needed if the augers seem to hesitate
while turning, but the engine maintains speed, or
continue turning with the auger control disengaged.
1. Loosen the rear hex bolt on the cable adjustment
bracket. See Figure 6.
2. Slide the cable adjustment bracket backwards
taking out the slack in the auger cable.
3. Retighten the rear hex bolt
4. Start engine and verify auger control engages and
disengages properly.
Figure 4
High Position
Middle Position
Low Position
Figure 5
WARNING
Do not over-tighten
the cable. Over-
tightening may
prevent the auger
from disengaging
and compromise the
safety of the snow
thrower.
If auger continues
to rotate with the
control disengaged,
shut off engine and
readjust.
Never attempt to
clean chute or make
any adjustment while
engine is running.
Over-inflating the
tire with excessive
pressure (well above
20 psi) may cause
the tire/rim to burst
with sufficient force
to cause serious
pressure.
Figure 6
Drive Cable
Auger Cable
Cable Ties
8
4
Throttle Control
The throttle control is located on the engine. It regulates
the speed of the engine and also stops the engine.
Drive Control
Located on the underside of the upper handle, the drive
control is used to engage/disengage wheels. Pull the
drive control against the upper handle to engage the
wheels; release to disengage.
Auger Control
Located on the top side of the upper handle, the auger
control is used to engage and disengage the augers.
Pull the auger control back against the upper handle to
engage the augers; release to disengage.
IMPORTANT: Refer to Auger Control Test on page 10
prior to operating your snow thrower. Read and follow
all instructions carefully and perform all adjustments
to verify your snow thrower is operating safely and
properly.
Discharge Chute
The direction snow is thrown can be changed by turning
the lower chute with the chute handle. The distance
snow is thrown can be adjusted by raising the upper
chute for greater distance, or lowering for less distance.
Loosen the wing nut on the side of the discharge chute
to adjust. Pivot the chute to desired position, and
retighten wing nut.
Ignition Key
The ignition key must be inserted and snapped in place
in order for the engine to start. Remove the ignition key to
prevent unauthorized use of equipment. Do NOT attempt
to turn the key.
Shave Plate
The shave plate maintains contact with pavement as
the snow thrower is propelled, allowing snow close to
pavement’s surface to be discharged.
Skid Shoe
The space between the shave plate and the ground can
be adjusted. For close snow removal, place skid shoes in
the low position. Use middle or high position when area to
be cleared is uneven or on gravel surfaces.
Engine Operating Controls
Refer to the separate engine manual for engine operat-
ing controls and their functions.
Figure 7
Be familiar with
all the controls on
the snow thrower
and their proper
operation. Know how
to stop the machine
and disengage them
quickly.
Never make adjust-
ments to the chute
assembly unless
both controls are
disengaged and the
operator is standing
beside the unit.
WARNING
/IL&ILL
&UEL#AP
3TARTER
(ANDLE
/IL$RAIN
#HOKE
4HROTTLE#ONTROL
0RIMER
3PARK0LUG
-UFFLER
Know
Your Snow
Thrower
Chute Assembly
Clean-out Tool
Auger
Shave Plate
Gasoline Cap
Starter Rope
Upper Chute
Skid Shoe
Chute Handle
Chute Knob
Auger Control
Upper Handle
Drive
Control
9
Before Starting Engine
ATTENTION: YOU MUST CHECK OIL
LEVEL BEFORE OPERATION. LEVEL
MUST BE AT FULL MARK ON DIPSTICK
BEFORE ENGINE IS STARTED.
NOTE: Failure to follow this procedure may result in
serious engine damage which will not be covered by
warranty.
Gas and Oil Fill-up
Service the engine with gasoline and oil as instructed
in the separate engine manual packed with your
snowthrower. Read instructions carefully.
WARNING: Never fill fuel tank indoors.
Never fill fuel tank with engine running
or while engine is hot. Do not smoke
when filling fuel tank.
Attach spark plug wire to spark plug. Make certain the
metal loop on the end of the spark plug wire (inside
the boot) is fastened securely over the metal tip on the
spark plug.
Make certain the auger and drive control bails are in
the disengaged (released) position.
IMPORTANT: ENGINE WILL NOT START UNLESS
IGNITION KEY IS INSERTED INTO IGNITION SLOT IN
CARBURETOR COVER. DO NOT TURN IGNITION KEY.
To Start Engine
Move choke lever to FULL CHOKE position (cold
engine start). If engine is warm, place choke in OFF
position instead of ON.
Push primer button two or three times. If unit is
equipped with an electric starter, push primer button
one time only. If engine is warm, do not prime.
NOTE: Always cover vent hole in primer button with finger
while pushing. Additional priming may be necessary for
the first start if temperature is below 15°F (-9°C).
Make certain the auger and drive control bails are in
the disengaged (released) position.
Move throttle control up to FAST position. Make
certain the ignition key is in the ignition slot. Be certain
it snaps into place. Do not turn key.
Electric Starter (Optional)
WARNING: The optional electric starter
is equipped with a three-wire power
cord and plug, and is designed to oper-
ate on 120 volt AC Household current. It
must be properly grounded at all times
to avoid the possibility of electric shock
which may be injurious to the operator.
5
Operation
WARNING
Follow all instructions carefully. Determine that your
house wiring is a three wire grounded system. Ask a
licensed electrician if you are not certain. If your house
wiring system is not a three-wire grounded system, do
not use this electric starter under any conditions. If your
system is grounded and a three hole receptacle is not
available at the point your starter will normally be used,
one should be installed by a licensed electrician.
WARNING: When connecting “power
cord, first connect cord to “switch
box” on engine, and then plug the
other end into a three-wire grounded
household receptacle. When discon-
necting power cord, always unplug the
end in the household receptacle first.
Connect power cord to switch box on engine.
Plug the other end of power cord into a three-wire,
grounded 120 volt AC receptacle.
Push starter button to engage starter motor and
crank engine. (When engaging the electric starter, a
slight hesitation of a few seconds may occur before
the engine starts to turn. This is normal and is not
harmful to the engine.)
When engine starts, release starter button, and
move choke gradually to OFF. If engine falters, move
choke immediately to FULL and then gradually to
OFF.
CAUTION: This electric starter is not equipped with
a thermal cut-out switch. Do not crank engine for
more than a total of 20 seconds without allowing
electric starter to cool down for 10 minutes or
severe damage to electric starter can result.
NOTE: If the starter motor runs but the engine does not
turn over, the starter gear is apparently covered with ice
and frozen. Place the unit in a warm atmosphere until
the gear is free and the starter will engage.
Recoil Starter
Grasp starter handle (see Figure and pull rope out
slowly, until it pulls slightly harder.
Pull starter handle rapidly. Do not allow handle to
snap back. Allow it to rewind slowly while keeping a
firm hold on the starter handle. Repeat until engine
starts.
As engine warms up and begins to operate evenly,
rotate choke knob slowly to OFF position. If engine
falters, return to FULL choke, then slowly move to
OFF position.
Read, understand,
and follow all instruc-
tions and warnings
on the machine and
in this manual before
operating.
Use extreme care
when handling
gasoline. Gasoline is
extremely flammable
and the vapors are
explosive. Never fuel
the machine indoors
or while the engine
is hot or running.
Extinguish cigarettes,
cigars, pipes and
other sources of
ignition.
If your home’s wir-
ing system is not a
three-wire grounded
system, do not use
this electric starter
under any conditions.
If your home
electrical system
is grounded, but a
three-hole receptacle
is not available, do
not use your snow
throwers electric
starter.
10
5
Operation
WARNING
To Stop Engine
Run engine for a few minutes before stopping to help
dry off any moisture on the engine.
To help prevent possible freeze-up of starter,
proceed as follows.
Optional Electric Starter: Connect power cord to
switch box on engine, then to 120 volt AC receptacle.
With the engine running, push starter button and spin
the starter for several seconds. The unusual sound
made by spinning the starter will not harm engine or
starter. Disconnect the power cord from receptacle first,
and then from switch box.
Recoil Starter: With engine running, pull starter rope
with a rapid, continuous full arm stroke three or four
times. Pulling the starter rope will produce a loud clatter-
ing sound, which is not harmful to the engine or starter.
To stop engine, remove the ignition key. Do not turn
key. Disconnect the spark plug wire from the spark
plug to prevent unintended starting while equipment is
unattended.
NOTE: Do not lose ignition key. Keep it in a safe place.
Engine will not start without the ignition key.
Wipe all snow and moisture from the carburetor cover in
the area of the control levers. Also, move control levers
back and forth several times.
WARNING: The temperature of muffler
and the surrounding areas may
exceed 150º F. Avoid these areas
Auger Control Test
IMPORTANT: Perform the following test before operat-
ing the snow thrower for the first time and at the start of
each season.
Check the adjustment of the auger control as follows:
1. When the auger control is released and in the
disengaged “up” position, the cable should have very
little slack, but should NOT be tight.
WARNING: Do not over-tighten the
cable. Over-tightening may prevent
the auger from disengaging and
compromise the safety of the snow
thrower.
2. In a well-ventilated area, start the snow thrower
engine as instructed earlier in this section under the
heading Starting Engine. Make sure the throttle is
set in the FAST position.
3. While standing in the operator’s position (behind the
snow thrower) engage the auger.
4. Allow the auger to remain engaged for approximately
ten (10) seconds before releasing the auger control.
Repeat this several times.
5. With the engine running in the FAST position and the
auger control in the disengaged “up” position, walk to
the front of the machine.
6. Confirm that the auger has completely stopped
rotating and shows NO signs of motion.
IMPORTANT: If the auger shows ANY signs of rotating,
immediately return to the operators position and shut
off the engine. Wait for all moving parts to stop before
readjusting the auger control cable as shown in the
“Setup And Adjustment” section on page 7.
Operating The Snowthrower
NOTE: Allow the engine to warm up for a few minutes
as the engine will not develop full power until it reaches
operating temperature.
Adjust the discharge chute as desired. Do not throw
snow toward a building as hidden objects could be
discharged with enough force to cause damage.
Start the engine as instructed previously.
Making certain no bystanders or obstacles are in front
of the unit, squeeze the auger control bail completely
against the upper handle to fully engage the augers.
Release the auger control bail and the augers will
stop.
While the auger control handle is engaged, squeeze
the drive control bail completely against the upper
handle to engage the wheels. Release the drive
control bail and the wheels will stop.
As the snowthrower starts to move, maintain a firm
hold on the handle, and guide the snowthrower along
the path to be cleared.
Release the bails to stop the snowthrowing action and
forward motion.
NOTE: Your unit is equipped with a clutch in the transmis-
sion. If the wheels stop turning while trying to discharge
large volumes of snow, immediately disengage the drive
control bail and allow the rotating augers to discharge
snow from the housing. Continue operation reducing
clearing width.
The operation of
any snow thrower
can result in foreign
objects being thrown
into the eyes, which
can damage your
eyes severely. Always
wear safety glasses
while operating the
snow thrower, or
while performing
any adjustments or
repairs on it.
Be sure no one other
than the operator is
standing near the
snow thrower while
starting engine or
operating snow
thrower. Never run
engine indoors or in
enclosed, poorly ven-
tilated areas. Engine
exhaust contains
carbon monoxide, an
odorless and deadly
gas. Keep hands,
feet, hair and loose
clothing away from
any moving parts
on engine and snow
thrower.
11
5
Operation
Never use your
hands to clean
snow and ice
from the chute
assembly or
auger housing.
The temperature of
muffler and the sur-
rounding areas may
exceed 150° F. Avoid
these areas
WARNING
Operating Tips
For most efficient snow removal, remove snow
immediately after it falls.
Discharge snow downwind whenever possible. Slightly
overlap each previous swath.
Set the slide shoes 1/4” below the shave plate for
normal usage. The slide shoes may be adjusted to low
position, see Figure for hard-packed snow.
NOTE: It is not recommended that you operate
this snowthrower on gravel as loose gravel can be
easily picked up and thrown by the auger causing
personal injury, property damage and/or damage to your
snowthrower.
If for some reason, you have to operate the
snowthrower on gravel, keep the slide shoe in the
highest position for maximum clearance between the
ground and the shave plate.
Be certain to follow the precautions listed under “To
Stop Engine” to prevent possible freeze-up.
Clean the snowthrower thoroughly after each use.
Clean-Out Tool
WARNING: Never use your hands to
clear a clogged chute assembly. Shut
off engine and remain behind handles
until all moving parts have stopped
before unclogging.
Release both the auger control and the drive/auger
control lock.
Stop the engine by moving the throttle to the stop
position.
Remove the clean-out tool from the mounting clip.
Use the shovel-shaped end of the clean-out tool to
remove any snow and ice in the chute assembly.
Re-fasten the clean-out tool to the mounting clip on
the rear of the auger housing and restart engine.
While standing in the operator’s position (behind the
snow thrower), engage the auger control for a few
seconds to clear any remaining snow or ice from the
chute assembly before continuing to clear snow.
12
Always stop engine,
disconnect spark
plug, and ground
against engine before
cleaning, lubricating
or doing any kind
of maintenance or
adjustments on your
machine.
WARNING
6
Maintenance
& Service
General Recommendations
1. Always observe safety rules when performing any
maintenance.
2. The warranty on this snow thrower does not cover
items that have been subjected to operator abuse or
negligence. To receive full value from the war
-
ranty, operator must maintain the snow thrower as
instructed in this manual.
3. Periodically check all fasteners and hardware to
make sure these are tight.
WARNING: Before servicing, repairing,
lubricating or inspecting, disengage all
controls and stop engine. Wait until all
moving parts have come to a complete
stop. Disconnect spark plug wire and
ground it against the engine to prevent
unintended starting. Always wear safety
glasses during operation or while per-
forming any adjustments or repairs.
Shave Plate and Skid Shoes
The shave plate and skid shoes on the bottom of the
snow thrower are subject to wear. They should be
checked periodically and replaced when necessary.
To remove skid shoes:
1. Remove the four carriage bolts and hex flange nuts
which secure them to the snow thrower.
2. Reassemble new skid shoes with the four carriage
bolts (two on each side) and hex flange nuts. Refer
to Figure 9.
To
remove shave plate:
1. Remove the carriage bolts and hex nuts which attach
it and the skid shoes to the snow thrower housing.
2. Reassemble new shave plate, making sure heads of
carriage bolts are to the inside of housing. Tighten
securely.
Augers
The augers are secured to the spiral shaft with two
shear pins and cotter pins. If the auger should strike
a foreign object or ice jam, the snow thrower is
designed so that the pins may shear.
If the augers will not turn, check to see if the pins
have sheared. When replacing pins, spray an oil
lubricant into shaft before inserting new pins.
Lubrication
1. Lubricate pivot points on the auger control and drive
control with a light engine oil once a season. See
Figure 10.
2. Lubricate the face of the auger idler bracket with a
light weight cold weather lubricant at least once a
season. See Figure 10.
Engine
Refer to the separate engine manual packed with your
unit for all engine maintenance.
Check V-Belts
Follow instructions below to check condition of drive belts
every 50 hours of operation.
1. Remove
the plastic belt cover on the front of the
engine by removing the self-tapping screw and press
-
ing the plastic tabs to release the belt cover.
2. Visually
inspect for frayed, cracked, or excessively
worn out belts. Replace, if necessary.
Replacing Belts
NOTE: There are two belts on this snow thrower: an
auger belt and drive belt. It is recommended that both
belts be replaced at the same time.
1. Remove the spark plug wire from spark plug and ground it
against the engine to prevent accidental starting.
2. Drain gasoline from the gas tank, or place a piece
of plastic sheet underneath the gas cap to prevent
gasoline leakage.
Figure 10
NOTE: If auger contin-
ues to rotate with the
control disengaged,
shut off engine and
re-adjust.
Lubricate
Lubricate
Figure 9
Shear Pin
Cotter Pin
Carriage
Bolt
Shave Plate
Hex Nut
Skid Shoe
Carriage
Bolt
Hex Nut
NEVER replace the
auger shear pins with
standard pins or fas-
teners. Any damage
to the auger gearbox
or other components,
as a result of doing
so, will NOT be
covered by your snow
throwers warranty.
13
Always stop engine,
disconnect spark
plug, and ground
against engine before
cleaning, lubricating
or doing any kind
of maintenance or
adjustments on your
machine.
WARNING
6
Maintenance
& Service
3. Remove the self tapping screw which secures the
belt cover to the frame. Remove the belt cover by
pushing in on the sides of the cover to release the
plastic tabs. Pull the belt cover out from around the
engine and chute. See Figure 11.
Auger Belt
NOTE: Drain the gasoline from the snowthrower, or
place a piece of plastic under the gas cap.
1. Tip the snow thrower up and forward so that it rests
on the auger housing. Remove the belt keeper as
shown in Figure 13. Return the snow thrower to its
upright position to complete the following steps.
2. Slip the front auger belt off of the engine pulley
pushing it forward and rolling in off of the pulley. See
Figure 12.
3. Squeeze the auger control handle to release the
auger brake, which is the tab that holds the belt onto
the auger pulley. Remove the belt.
4. Replace with new belt after replacing the drive belt.
Drive Belt
NOTE: Replace the drive belt before reassembling the
new auger belt.
NOTE: Drain the gasoline from the snowthrower, or
place a piece of plastic under the gas cap.
1. Tip the snow thrower up and forward so that it rests
on the auger housing.
2. Remove
the spring that connects the transmission to
a bolt on the engine frame. See Figure 13.
NOTE: It may be easier to first remove the flange lock
nut, then use needle-nosed pliers to firmly grip spring
and remove from bolt.
3. Pivot the transmission forward to release pressure on
the drive belt. Remove belt from transmission pulley.
4. Remove
the drive belt from around the engine pulley,
and away from the unit.
5. Place the new drive belt into the groove on the
engine pulley. See Figure 12.
6. Tilt
the transmission forward and position the drive
belt onto the transmission pulley.
7. Reconnect the spring to the bolt on the engine frame and
secure the transmission. Reinstall the flange lock nut.
8. Install
new auger belt.
Figure 12
Figure 11
Plastic Tab
Figure 13
Drive
Belt
Engine
Pulley
Auger Belt
Auger
Pulley
Idler
Bracket
Drive Pulley
Belt Keeper
Drive Belt
Spring
14
Observe the following, when preparing your snow
thrower for off-season storage:
Drain fuel into an approved container outdoors, away
from any open flame. Allow engine to cool. Extin-
guish cigarettes, cigars, pipes and other sources
of ignition prior to draining fuel. Fuel left in engine
during warm weather deteriorates and will cause
serious starting problems.
If unit is to be stored over 30 days, prepare for
storage as instructed in the separate engine manual
packed with your unit.
Run engine until fuel tank is empty and engine stops
due to lack of fuel.
Remove gasoline from carburetor and fuel tank to
prevent gum deposits from forming on these parts
and causing possible malfunction of engine.
Drain carburetor by pressing upward on bowl drain,
located below the carburetor cover.
Fuel stabilizers, such as STA-BIL®, are an accept
-
able alternative in minimizing the formation of fuel
gum deposits during storage. Do not drain carburetor
if using a fuel stabilizer.
Wipe equipment with an oiled rag to prevent rust.
Remove spark plug and pour one ounce of engine
oil through spark plug hole into cylinder. Cover spark
plug hole with rag. Crank engine several times to
distribute oil. Replace spark plug.
Follow the lubrication recommendations found in the
Maintenance Section.
Always store the snow thrower in a clean, dry area.
7
Off-Season
Storage
Never store snow
thrower with fuel
in tank indoors or
in poorly ventilated
areas, where fuel
fumes may reach an
open flame, spark
or pilot light as on a
furnace, water heater,
clothes dryer or
gas appliance.
Drain fuel into an
approved container
outdoors, away from
any open flame. Be
certain engine is
cool. Do not smoke.
Fuel left in engine
during warm weather
deteriorates and will
cause serious start-
ing problems.
Do not drain carbure-
tor if using fuel
stabilizer. Never use
engine or carburetor
cleaning products
in the fuel tank or
permanent damage
may occur.
WARNING
15
NOTE: This section
addresses minor
service issues. For
further details,
contact customer
assistance.
8
Trouble-
Shooting
CauseProblem Remedy
Engine fails to start
1. Choke not in ON position.
2. Spark plug wire disconnected.
3. Fuel tank empty or stale fuel.
4. Engine not primed.
5. Faulty spark plug.
6. Blocked fuel line.
7. Safety key not in ignition on engine.
8. Fuel shut-ff valve closed. (If Equipped)
1. Move choke to ON position.
2. Connect wire to spark plug.
3. Fill tank with clean, fresh gasoline.
4. Prime engine as instructed in
“Operating Your Snow Thrower.
5. Clean, adjust gap, or replace.
6. Clean fuel line.
7. Insert key fully into the switch.
8. Open fuel shut-off valve.
Engine runs erratic
1. Move choke lever to OFF position.
2. Clean fuel line; fill tank with clean,
fresh gasoline.
3. Drain fuel tank. Refill with
fresh fuel.
4. Contact Service Center.
1. Unit running on CHOKE.
2. Blocked fuel line or stale fuel.
3. Water or dirt in fuel system.
4. Carburetor out of adjustment.
Engine overheats
1. Contact Service Center.1. Carburetor not adjusted properly.
Loss of power
1. Connect and tighten spark plug
wire.
2. Remove ice and snow from gas
cap. Be certain vent hole is clear.
3. Contact Service Center.
1. Spark plug wire loose.
2. Gas cap vent hole plugged.
3. Exhaust port plugged.
Unit fails
to propel itself
1. Adjust drive control cable. Refer to
Adjustments”.
2. Replace drive belt.
1. Drive control cable in need of adjust-
ment.
2. Drive belt loose or damaged.
Excessive
Vibration
1. Loose parts or damaged auger.
1. Stop engine immediately and
disconnect spark plug wire. Tighten
all bolts and nuts. If vibration
continues, have unit serviced by a
Service Center.
Unit fails
to discharge snow
1. Stop engine immediately and
disconnect spark plug wire. Clean
chute assembly and inside of
auger housing with clean-out tool
or a stick.
2. Stop engine immediately and
disconnect spark plug wire.
Remove object from auger with
clean-out tool or a stick.
3. Refer to “Auger Control Test” .
4. Refer to Maintenance section.
5. Replace with new shear pin(s).
1. Chute assembly clogged.
2. Foreign object lodged in auger.
3. Auger control cable in need of adjust-
ment.
4. Auger belt loose or damaged.
5. Shear pin(s) sheared.
16
9
Illustrated
Parts/
Pièces
détachés
45
20
9
18
34
21
22
33
28
20
30
31
24
25
27
10
38
3
21
15
12
13
16
46
3
20
47
23
35
5
17
11
14
20
50
26
19
44
29
41
43
36
42
39
40
37
20
7
6
3
2
1
43
49
48
4
8
17
REF PART
NO. NO.
N° DE N° DE
RÉF PIÈCE DE SCRIP TION DE SCRIP TION
1 684-04037 Chute As sem bly Goulotte
2 710-04071 Carriage Screw 5/16-18 x 1.0 Vis ordi naire 5/16-18 x 1,0
3 710-0451 Carriage Bolt 5/16-18 x .75 Boulon ordi naire 5/16-18 x 0,75
4 710-04606 Screw 5/16-18 x .43 Vis 5/16-18 x 0,43
5 720-04072 Star Knob -Black Bouton étoile- noir
720-04071 Star Knob -Yel low Bouton étoile- jaune
6 731-04388A Chute Handle Poignée - goulotte d’éjection
7 731-04354B Up per Chute Goulotte supérieur
8 750-04852 Shoulder Spacer .385 x .785 x .538 Entretoise epaulée 0,385 x 0,785 x 0,538
9 731-04127 Lower Chute 5" Dia Goulotte d’éjection inférieur dia. 5 po
10 731-04353 Ring-Lower Chute Bague - goulotte d’éjection inférieur
11 731-2636A Chute Adapter 5" Dia. Adaptateur de goulotte d’éjection 5 po diam.
12 732-04111 Chute Ad just ment Spring Ressort d’ajustement - goulotte d’éjection
13 712-04064 Hex L-Flanged Nut 1/4-20 Gr. F Ny lon Contre-écrou à embase 1/4-20 Qual. F ny lon
14 731-2643 Chute Clean-Out Tool Outil de dégagement de la goulotte
15 731-2635 Mount ing Bracket Support de mon tage
16 725-0157 Ca ble Tie Attache-câble
17 710-0134 Carriage Bolt 1/4-20 x .62 Boulon ordi naire 1/4-20 x 0,62
18 710-0520 Hex Screw 3/8-16 x 1.50 Vis à tête hexagonale 3/8-16 x 1,50
19 710-04484 Hex Wash. Scr. AB 5/16-18 x .75 Vis à tête hex. AB 5/16-18 x 0,75
20 712-04063 Flange Locknut 5/16-18 Gr. F, Ny lon Contre-écrou à embase 5/16-18 Qual. F, ny lon
21 712-04065 Flange Lock-Nut 3/8-16 Gr. F Ny lon Contre-écrou à embase 3/8-16 Qual. F ny lon
22 741-0919 Ball Bear ing 20 x 47 x 14:6204:DS Roulement à billes 20 x 47 x 14:6204:DS
23 715-04020 Spi ral Pin Attache
24 726-04012 Push Nut Écrou à enfoncer
25 731-04218B Im pel ler Ventilateur
26 732-0611 Ex ten sion Spring Ressort d’extension
27 736-0174 Wave Washer .660 ID x .88 OD x .010 Rondelle ondulée 0,660 DI x 0,88 DE x 0,010
28 738-0281 Shoulder Scr .625 Dia. x .170 Vis à épaulement dia. 0,625 x 0,170
29 741-0245 Hex. Flange Bear ing.751" ID Roulement à bride à six pans 0,751 DI
30 741-0309 Self-align ing bear ing Roulement auto-aligneur
31 750-04191 Spacer Entretoise
32 756-04249 Flat Idler Tendeur
33 784-0434 Auger Idler Bracket Support du tendeur
34 790-00075 Bear ing Hous ing Carter de la roulement
35 618-04292A Au ger Gear box As sem bly - 22" Boîtier d’engrenage - 22 po
618-04294A Au ger Gear box As sem bly - 24" Boîtier d’engrenage - 24 po
36 684-04113A Au ger As sem bly - LH Tarière CG
37 684-04114A Au ger As sem bly -RH Tarière - CD
38 684-04166A Au ger Hous ing 22" Logement des tarières 22 po
684-04165 Au ger Hous ing 24" Logement des tarières 24 po
39 714-04040 Bow-Tie Cotter Pin Goupille fendue
40 731-04870 Spacer Entretoise
41 736-0351 Flat Washer .76 ID x 1.5 OD x .03 Rondelle plate 0,76 DI x 1,50 DE x 0,030
42 738-04124A Shear Pin .25 x 1.50 Gr. 2 Goupille 0,25 x 1,50 Qual. 2
43 741-0493A Flange Bear ing Roulement à bride
44 790-00087A Hex Brg. Hous ing Carter de la roulement
790-00138A Hex. Brg. Hsg. (w/Grease fit ting hole) Carter de la roulement (trou-raccord de graisse)
45 736-0267 Flat Washer .38 ID x .87 OD x .09 Rondelle plate 0,38 DI x 0,87 DE x 0,09
46 784-5580 Slide Shoe (Stan dard) Pat in ordi naire
47 790-00117 Shave Plate 22" Lame plate 22 po
790-00120 Shave Plate 24" Lame plate 24 po
48 737-3000 Grease Fit ting (optional) Raccord graisseur (en op tion)
49 731-04870 Spacer (24" only) Entretoise (24 po seulement)
50 710-0260A Carriage Bolt 5/16-18 x .62 Boulon ordi naire 5/16-10 x 0,62
31A-3AAD1
7.23.07
9
For parts and/or
accessories refer to
customer support on
page 2.
Adressez-vous au
«Service après-vent
à la page 2 pour ce qui
concerne les pièces
et/ou accessoires.
Illustrated
Parts/
Pièces
détachés
18
9
Illustrated
Parts/
Pièces
détachés
34
36
35
2
4
5
55
1
13
3
9
8
10
12
11
39
21
23
24
40
43
49
47
51
51
51
51
48
46
45
44
50
41
14
4
3
31
27
30
17
29
3
32
42
38
18
20
22
28
16
37
53
52
54
33
17
26
25
19
7
6
54
19
29
56
19
REF PART
NO. NO.
N° DE DE
RÉF PIÈCE DE SCRIP TION DE SCRIP TION
1 710-0449 Carriage Bolt 5/16-18 x 2.25 Gr. 1 Boulon ordi naire 5/16-18 x 2,25 Qual
2 710-0605 Oval C-Sunk Screw 1/4-20 x 1.825" Lg. Vis à tête noyée 1/4-20 x 1,825 po de lg
3 710-04484 Hex Wash. Scr. AB 5/16-18 x .75 Vis à tête hex. AB 5/16-18 x 0,75
4 712-04064 Flanged Lock Nut 1/4-20 Gr. F Ny lon Écrou de blocage 1/4-20 Qual. F
5 720-0284 Knob -Black Bouton - noir
6 725-0157 Ca ble Tie Attache câble
7 746-04256 Drive Ca ble Câble d'entraînement
8 746-04236 Au ger Ca ble Câble de la tarière
9 747-1161A Au ger Con trol Han dle Poignée de commande de la tarière
10 747-1214 Drive Con trol Han dle Poignée de commande d’entraînement
11 749-04147 Lower Han dle Guidon inférieur
12 749-1092A Up per Han dle Guidon supérieur
13 790-00053 Han dle Tab Patte d’attache
14 618-04296A Trans mis sion As sem bly Essieu
16 710-0809 Hex Bolt 1/4-20 x 1.25 Boulon hex. 1/4-20 x 1,25
17 710-1652 Screw 1/4-20 x .625 Vis 1/4-20 x 0,625
18 711-1364 Clevis Pin 1/4 x 1.3725 Axe de chape 1/4 x 1,3725
19 714-0115 Cot ter Pin Goupille fendue
20 714-04040 Bow Tie Cotter Pin Goupille fendue
21 715-0249 Spring Roll Pin 1.12" Lg. Goupille ressort à spirale 1,12 po de lg.
22 717-04066A Pinion 14T, 12DP Pignon 14 dents, 12DP
23 717-04073A Gear-70 Tooth Engrenage - 70 dents
24 732-0429A Tension Spring .50 OD x 3.97" Lg. Ressort de ten sion 0,50 DE x 3,97 po de lg
25 736-0192 Flat Washer 0.531 ID x 0.93 OD x .090 Rondelle plate 0,531 DI x 0,930 DE x 0,090
26 738-04184A Shoulder Screw 1/4-20 Vis épaulée 1/4-20
27 738-0924A Carriage Screw 1/4-28 Boulon ordi naire 1/4-28
28 741-0245 Hex Flage Bearing Roulement
29 741-04108 Hex. Flange Bear ing 0.75" I.D. Roulement à bride hex. de 0,75 po D.I.
30 756-0625 Ca ble Roller Sup port
31 784-0419C Frame Châssis
32 790-00223A Au ger Ca ble Bracket Support - câble de tarière
33 790-00224 Au ger Ca ble Ad just ment Bracket Support de réglage - câble de tarière
34 634-04282A Comp. Wheel Ass’y 10 x 4 Snow Hog Ens.de roue comp 10,0 x 4,0 Snow Hog
734-2047 Tire 4.10 x 3.0" Snow Hog Pneu 4,10 x 3,0 po Snow Hog
634-04281A Rim 4.0" x 3.0" Jante 4,0 x 3,0 po
734-0255 Air Valve Soupape à air
35 710-0627 Hex Hd.Cap Scr. 5/16-24 x 0.75 Gr. 5 Boulon hex 5/16-24 x 0,75 Qual. 5
36 736-0242 Cup. Wash. .340 ID x .872 OD x .060 Rondelle creuse 0,340 DI x 0,872 DE x 0,060
37 738-1231 Axle .75 OD x 17.594 Lg. Essieu 0,75 DE x 17,594 lg.
38 710-0224 Hex Screw #10-16 x .50 Vis no. 10-16 x 0,50
39 710-0654A Hex Wash HD Tap Scr 3/8-16 x 1.00 Vis autotaraudée 3/8-16 x 1,00
40 710-0696 Hex Scr. 3/8-24 x .875" Lg. Gr. 8 Vis à tête hex.3/8-24 x 0,875 po Qual. 8
41 710-1245B Hex Screw 5/16-24 x .875 Gr. 8 Vis à tête hex. 5/16-24 x 0,875 Qual. 8
42 731-04162A Belt Cover Couvercle de courroie
43 736-0247 Flat Washer .406 ID x 1.25 OD x .160 Rondelle plate 0,406 DI x 1,25 DE x 0,160
44 736-0505 Flat Washer .34 ID x 1.50 OD x .150 Rondelle plate 0,34 DI x 1,50 DE x 0,150
45 748-04067A Pulley Adap tor .75 Dia. w/pins Adaptateur de poulie avec épingles
46 750-1355 Spacer .8760 ID x 1.25 OD x .190 Entretoise 0,8760 DI x 1,25 DE x 0,190
47 750-1356 Spacer .8760 ID x 1.25 OD x .86 Entretoise 0,8760 DI x 1,25 DE x 0,86
48 754-04013 “V”-Belt 3/8 x 21.108 Lg. Courroie trapézoïdale 3/8 x 21,108 lg.
49 754-04014 “V”-Belt 3/8 x 26.680 Lg. Courroie trapézoïdale 3/8 x 26,680 lg.
50 756-04024 Auger Pul ley 6.0 x 3/8 Poulie de tarière 6,0 x 3/8
51 756-0569 V-Pulley Half 3/8 x 2.6 Poulie - moitié 3/8 x 2,6
52 710-0456 Screw #10-16 x .50 Vis no. 10-16 x 0,50
53 790-00064 Heat Shield Protecteur
54 736-0160 Flat Washer .53 ID x .93 OD x .050 Rondelle plate 0,53 DI x 0,93 DE x 0,05
55 736-0451 Saddle Washer .320 ID x .93 OD x .060 Rondelle 0,320 DI x 0,93 DE x 0,060
56 750-04913 Spacer .260 ID x .466 OD x .20" Lg. Entretoise 0,260 DE x 0,466 DE x 0,20 po de lg.
57 731-05672 Spacer 1.25 x .757 x .71 Entretoise 1,25 x 0,757 x 0,71
31A-3AAD2
7.23.07
9
For parts and/or
accessories refer to
customer support on
page 2.
Adressez-vous au
«Service après-vent
à la page 2 pour ce qui
concerne les pièces
et/ou accessoires.
Illustrated
Parts/
Pièces
détachés
20
10
Warranty
Failure to comply
with suggested
maintenance
and lubrication
specifications will
void warranty.
TWO YEAR LIMITED WARRANTY
The limited warranty set forth below is given by MTD Products Limited with respect to new merchandise purchased and
used in Canada and/or its territories and possessions (either entity respectively, “MTD”).
MTD warrants this product (excluding its normal wear parts as described below) against defects in material and
workmanship for a period of two (2) years commencing on the date of original purchase and will, at its option, repair
or replace, free of charge, any part found to be defective in materials or workmanship. This limited warranty shall
only apply if this product has been operated and maintained in accordance with the Operators Manual furnished with
the product, and has not been subject to misuse, abuse, commercial use, neglect, accident, improper maintenance,
alteration, vandalism, theft, fire, water, or damage because of other peril or natural disaster. Damage resulting from the
installation or use of any part, accessory or attachment not approved by MTD for use with the product(s) covered by
this manual will void your warranty as to any resulting damage.
Normal wear parts are warranted to be free from defects in material and workmanship for a period of thirty (30) days
from the date of purchase. Normal wear parts include, but are not limited to items such as: batteries, belts, blades,
blade adapters, grass bags, rider deck wheels, seats, snow thrower skid shoes, friction wheels, shave plates, auger
spiral rubber, tires, engine oil, air filters and spark plugs.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH PROOF OF PURCHASE, through your local
authorized service dealer. To locate the dealer in your area contact MTD Products Limited, Kitchener, ON N2G 4J1, or
call 1-800-668-1238 or log on to our Web site at www.mtdcanada.com.
This limited warranty does not provide coverage in the following cases:
a. The engine or component parts thereof. These items may carry a separate manufacturer’s warranty. Refer to
applicable manufacturer’s warranty for terms and conditions. The Powermore engine is not excluded under this
agreement.
b. Log splitter pumps, valves, and cylinders have a separate one-year warranty.
c. Routine maintenance items such as lubricants, filters, blade sharpening, tune-ups, brake adjustments, clutch
adjustments, deck adjustments, and normal deterioration of the exterior finish due to use or exposure.
d. Service completed by someone other than an authorized service dealer.
e. MTD does not extend any warranty for products sold or exported outside of Canada, including possessions and
territories.
f. Replacement parts that are not genuine MTD parts.
g. Transportation charges and service calls.
h. If Products are used commercially. (MTD may separately offer Limited Commercial Warranties on certain select
products. Ask your dealer or retailer for details or contact MTD Service for more information.)
No implied warranty, including any implied warranty of merchantability of fitness for a particular purpose,
applies after the applicable period of express written warranty above as to the parts as identified. No other
express warranty, whether written or oral, except as mentioned above, given by any person or entity, including
a dealer or retailer, with respect to any product, shall bind MTD. During the period of the warranty, the exclu-
sive remedy is repair or replacement of the product as set forth above.
The provisions as set forth in this warranty provide the sole and exclusive remedy arising from the sale. MTD
shall not be liable for incidental or consequential loss or damage including, without limitation, expenses
incurred for substitute or replacement lawn care services or for rental expenses to temporarily replace a
warranted product.
Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how
long an implied warranty lasts, so the above exclusions or limitations may not apply to you.
In no event shall recovery of any kind be greater than the amount of the purchase price of the product sold. Alteration
of safety features of the product shall void this warranty. You assume the risk and liability for loss, damage, or
injury to you and your property and/or to others and their property arising out of the misuse or inability to use the
product.
This limited warranty shall not extend to anyone other than the original purchaser or to the person for whom it was
purchased as a gift.
HOW LOCAL LAWS RELATE TO THIS WARRANTY: This limited warranty gives you specific legal rights, and you
may also have other rights that vary in different jurisdictions.
IMPORTANT: Owner must present Original Proof of Purchase to obtain warranty coverage.
MTD Products Ltd., P. O. BOX 1386, KITCHENER, ON N2G 4J1; Phone: 1-800-668-1238
12.16.06
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

MTD L-Style Manuel utilisateur

Catégorie
Souffleuses à neige
Taper
Manuel utilisateur

dans d''autres langues