Sony MZ-B50 Le manuel du propriétaire

Marque: Sony

Modèle: MZ-B50

Catégorie: Joueurs de minidisc

Taper: Le manuel du propriétaire

3-868-000-15(1)

Portable

MiniDisc Recorder

Operating Instructions ______________________

Manual de instrucciones ____________________

Mode d’emploi

___________________________

MZ-B50

Portable MiniDisc Recorder MZ-B50

2-GB

To prevent fire or shock hazard, do

not expose the unit to rain or

moisture.

To avoid electrical shock, do not

open the cabinet. Refer servicing to

qualified personnel only.

Caution

The use of optical instruments with this

product will increase eye hazard.

CAUTION — INVISIBLE LASER

RADIATION WHEN OPEN

AVOID EXPOSURE TO BEAM

Information

For customers in the USA

Owner’s Record

The serial number is located on the inside

of the battery compartment lid and the

model number is located at the top and

bottom. Record the serial number in the

space provided below. Refer to them

whenever you call upon your Sony dealer

regarding this product.

Model No. MZ-B50

Serial No.

This equipment has been tested and found

to comply with the limits for a Class B

digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to

provide reasonable protection against

harmful interference in a residential

installation. This equipment generates,

uses, and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may

cause harmful interference to radio

communications. However, there is no

guarantee that interference will not occur

in a particular installation. If this

equipment does cause harmful

interference to radio or television

reception, which can be determined by

turning the equipment off and on, the user

is encouraged to try to correct the

interference by one or more of the

following measures:

— Reorient or relocate the receiving

antenna.

— Increase the separation between the

equipment and receiver.

— Connect the equipment into an outlet

on a circuit different from that to

which the receiver is connected.

— Consult the dealer or an experienced

radio/TV technician for help.

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions: (1) This device

may not cause harmful interference, and

(2) this device must accept any

interference received, including

interference that may cause undesired

operation.

You are cautioned that any changes or

modifications not expressly approved in

this manual could void your authority to

operate this equipment.

Note

This recorder does not support LP2/LP4 stereo

mode. The recording, playback, or editing of

tracks or discs recorded in LP mode is thus not

possible on this recorder.

IN NO EVENT SHALL SELLER BE

LIABLE FOR ANY DIRECT,

INCIDENTAL OR

CONSEQUENTIAL DAMAGES OF

ANY NATURE, OR LOSSES OR

EXPENSES RESULTING FROM

ANY DEFECTIVE PRODUCT OR

THE USE OF ANY PRODUCT.

WARNING

3-GB

For customers in the USA and

Canada who have purchased the

optional AC power adaptor

Before using the optional AC power

adaptor, do the following procedure to

attach the large clamp filter to the AC

power cord. You must affix the ferrite

core to comply with Part 15 of FCC rules.

1 Open the clamp filter.

2 Wind the AC power cord into the clamp

filter as shown below.

3 Separate the loops by a space of

approximately 1 cm (0.4 inches) as

shown below.

4 Close the clamp filter.

Maximum length:

approx. 3 cm (1.2

inches)

Approx. 1 cm

(0.4 inches)

Make sure the

clasps are fully

engaged.

4-GB

Table of contents

Preparing a power source ................................ 6

Recording an MD right away! ...........................8

Playing an MD right away! .............................. 11

Various ways of recording .............................. 13

VOR (Voice Operated Recording) .......................................................13

Recording from a microphone ..............................................................14

Recording from externally connected equipment .................................15

Recording with digital (optical) input (optical cable required) ......16

Recording with analog (line) input (line cable required) ...............17

To start/stop recording in sync with the source player

(Synchro-recording) ........................................................................18

Recording in monaural for double the normal recording time .............19

Setting the clock to stamp the recorded time ........................................19

Checking the remaining time or the recording position .......................20

Various ways of playback .............................. 22

Enhancing voice clarity during playback (Voice Up) ..........................22

Finding a point quickly (Easy Search) ..................................................22

Listening at a fast speed (Fast Playback) ..............................................23

Playing tracks repeatedly ......................................................................23

Emphasizing bass (DIGITAL MEGA BASS) ......................................24

Checking the remaining time or the playing position ...........................24

Locking the controls (HOLD) ...............................................................25

5-GB

Editing recorded tracks .................................. 26

Adding a track mark ............................................................................. 26

Track marking to divide a recording .............................................. 26

Track marking important points .................................................... 26

Erasing a track mark ............................................................................ 27

Erasing tracks ....................................................................................... 28

To erase a track .............................................................................. 28

To erase the whole disc .................................................................. 28

Moving recorded tracks ....................................................................... 29

Labeling recordings .............................................................................. 29

Power sources ................................................ 32

When to replace the batteries ............................................................... 32

Using house current ............................................................................. 32

Additional information .................................... 33

Precautions ........................................................................................... 33

Troubleshooting ................................................................................... 35

System limitations ................................................................................ 37

Messages .............................................................................................. 38

Specifications ....................................................................................... 40

What is an MD? ................................................................................... 41

Looking at the controls ........................................................................ 43

6-GB

Preparing a power source

This section explains how to prepare the recorder for battery-powered

operation. For information on connecting the recorder to an AC power

outlet, see page 32.

Insert dry batteries.

Unlock the control.

Back of the recorder

Press and slide the battery

compartment lid as shown in

the illustration.

Notes

• Do not use manganese dry batteries. If you do, recording may not be possible.

• Insert the e and E poles of the batteries correctly as shown on the recorder.

Close the lid.

Insert two LR6 (size AA)

alkaline dry batteries (not

supplied).

Slide HOLD to the direction of the arrow in the illustration.

HOLD

7-GB

Charging the built-in battery for the clock

When you use the recorder for the first time or after a long period of disuse, charge the

built-in battery for the clock. After setting the clock, leave the dry batteries installed for

about more than two hours so that the built-in battery is automatically charged. You can use

the recorder while charging. Note that various settings, such as clock, return to the factory

settings if you take out dry batteries while charging. Once charged, the recorder will

automatically charge the built-in battery while connected to dry batteries.When the built-in

battery is charged, the settings, such as clock, will remain for about one month after dry

batteries are taken out. For details on setting a clock, see page 19.

8-GB

Recording an MD right away!

Use the built-in microphones to record in stereo. Make sure the

record-protect tab on the disc is closed (page 42). The use of new

alkaline dry batteries is recommended. The recording may not be

possible if you use manganese dry batteries.

Insert a recordable MD.

1 Slide OPEN to open the lid. 2 Insert a recordable MD with the label

side facing up, and press down hard on

the lid (at the center of the front edge

as shown above) to close it firmly.

Select the microphone sensitivity.

1 Slide MIC SENS to H or L.

MIC SENS

MIC SENS When

H (high) recording a soft or a

sound in the distance

(e.g. to record a

meeting).

L (low) recording a laud or a

sound at close range

(e.g. to record a speech

through a microphone).

9-GB

Select the recording mode.

Record an MD.

1 Press zREC.

“REC” and “STEREO” appears, REC

indicator lights up, and then recording

starts.

You can monitor the recording

conditions, such as the recording

position, through the display or the REC

indicator (page 20).

If the disc is blank, the recording

starts from the beginning. If the

disc is partially recorded, the

recording automatically starts

from the end of the existing

material.

To stop recording, press xSTOP.

After you press the xSTOP button, the

recorder will automatically turn off in about 30

seconds.

To monitor the sound during recording.

Connect the supplied headphones/earphones with remote control to the i jack. You can adjust the

volume by turning the VOL control. This adjustment does not affect the recording level since the level

is adjusted automatically.

1 Slide REC MODE to STEREO.

When you set the REC MODE switch to MONO, the

recording will be in monaural, but the recording time

will be two times longer than in stereo.

Make sure not to switch the recording mode while

recording.

REC MODE

xSTOP

zREC

REC

indicator

built-in

microphones

Connect

firmly

Connect firmly

to i

To Press

Record partway through the

previous recording

NPLAY, >CUE/AMS or .REVIEW/AMS

to find the beginning of the material to be recorded,

press XPAUSE, and then press zREC. The

recorder changes to recording pause. Press

XPAUSE again to start recording.

Pause

XPAUSE while recording.

Press XPAUSE again to resume recording.

10-GB

If the recording does not start

• Make sure the recorder is not locked

(page 25).

• Make sure the MD is not record-protected

(page 42).

• Premastered MDs cannot be recorded over.

Notes

• For long recordings, it is recommended that

you power the recorder from a house current

using an optional AC power adaptor AC-

E30HG (page 32).

• The lid will not open during recording or until

“TOC Edit” disappears from the display after

the recording has completed.

• If the power supply is disrupted (i.e. the

batteries are removed or becomes exhausted

or the optional AC power adaptor is

disconnected) during a recording operation, or

while “TOC Edit” appears in the display, then

it will not be possible to open the lid until

power is restored.

• “Data Save” or “TOC Edit” flashes while data

of the recording (the track’s start and end

points, etc.) is being recorded. Do not move or

jog the recorder or disconnect the power

source while the indication is flashing in the

display. If you do, the material recorded up to

that point will not be saved to the disc.

• When you record through the microphones,

the various sounds made by the recorder will

also be recorded.

• Do not connect an optional AC power adaptor

during a recording operation if you are

operating the recorder on battery power. If you

do, the material recorded up to that point will

not be saved to the disc

• The built-in microphones do not operate

whenever an optional microphone is

connected into the MIC (PLUG IN POWER)

jack on the recorder.

• The built-in microphones do not operate

whenever an optical cable or a line cable is

connected into the LINE IN (OPTICAL) jack

on the recorder.

• Make sure not to switch the recording mode

while recording. If you do, recording may not

occur.

Remove the MD xSTOP to stop recording and open the lid. (The lid

does not open while “TOC Edit” flashing in the

display.)

The REC indicator flashes during recording pause. Track marks are not added while recording with

microphones, even when the recorder is paused.

To Press

11-GB

Playing an MD right away!

You can play recordable MDs or premastered MDs. Sound output

from the built-in speaker is monaural, but stereo listening is possible

through the supplied headphones/earphones with a remote control.

Insert an MD.

1 Slide OPEN to open the lid. 2 Insert an MD with the label side facing

up, and press down hard on the lid (at

the center of the front edge as shown

above) to close it firmly.

Play an MD.

1 Press NPLAY.

2 Turn VOL to adjust the volume.

The volume will be shown in the

display.

To stop play, press xSTOP.

Playback starts from the point you last stopped

playing.

After you press the

xSTOP button, the

recorder will automatically turn off in about 30

seconds.

VOL

xSTOP

NPLAY

to i

speaker

Connect firmly

Connect

firmly

to i

12-GB

To listen in stereo

Connect the supplied headphones/earphones with a remote control to the i jack on the recorder. On the

remote control, use the >N button to start playback, the xSTOP button to stop the recorder, and

the VOL control to adjust the volume. If you are using the remote control, you will hear short beeps

whenever you press the >N button, and a long beep whenever you press the xSTOP button.

If the play does not start

Make sure the recorder is not locked (page 25).

To locate a point quickly

Use the EASY SEARCH +/– buttons (page 22).

When using optional headphones/

earphones

Use only headphones/earphones with stereo

mini plugs. You cannot use headphones/

earphones with micro plugs.

Playback will switch automatically between

stereo and monaural according to the sound

source.

Notes

• The sound may skip during playback when the

recorder is exposed to continuous vibration,

such as while jogging.

• If the power supply is disrupted (i.e. the

batteries are removed or become exhausted or

the optional AC power adaptor is

disconnected) when the recorder is operating,

the lid may not open until the power is

restored.

To Press (Beeps in the headphones/earphones)

Find the beginning of the

current track

.REVIEW/AMS once (Press the control towards .

on the remote control). (Three short beeps)

Find the beginning of the

next track

> CUE/AMS once (Press the control towards >N

on the remote control). (Two short beeps)

Pause XPAUSE (Press X on the remote control). (Continuous

short beeps) Press XPAUSE again to resume play.

Go backwards while

playing

keep pressing .REVIEW/AMS (Press and hold the

control towards . on the remote control).

Go forward while playing

keep pressing >CUE/AMS (Press and hold the control

towards >N on the remote control).

Remove the MD xSTOP (x on the remote control) and open the lid.

To go backward or forward quickly without listening, press XPAUSE (X on the remote control) and

keep pressing

.REVIEW/AMS or >CUE/AMS (press and hold the control towards . or

>N on the remote control).

Once you open the lid, the point to start play will change to the beginning of the first track.

Stereo mini plug

Micro plug

13-GB

Various ways of recording

VOR (Voice Operated

Recording)

VOR causes the recorder to automatically

record when there is sound, and to pause

when there is no sound. This allows you

to record without troublesome button

operations.

1 Slide MIC SENS to H (high) or L

(low).

2 Slide REC MODE to STEREO.

When you set the REC MODE switch

to MONO, the recording will be in

monaural, but the recording time will

be two times longer than in stereo.

3 Insert a recordable MD and press

zREC.

4 Press VOR.

VOR turns on.

“VOR” appears in the display and the

VOR indicator lights up when the

recorder is recording. Both “VOR”

and the VOR indicator flash when the

recorder is not recording.

To cancel VOR while recording, press

VOR again.

“VOR” and the VOR indicator goes off and the

recorder changes to normal recording mode.

VOR automatically turns off when you press

the xSTOP button to stop recording.

Notes

• You cannot record with the built-in

microphones while an optional microphone is

connected to the MIC (PLUG IN POWER)

jack or an optical cable (not supplied) is

connected to the LINE IN (OPTICAL) jack.

• VOR is sensitive to the surrounding sound

conditions. Set the MIC SENS switch to H or

L to suit the conditions. If you cannot get the

desired recording results, cancel VOR and

record in manual mode.

• Power from the batteries is consumed as long

as VOR is on, even when recording is not

taking place (i.e., when “VOR” and the VOR

indicator flash.)

VOR

indicator

built-in

microphones

MIC SENS

zREC

REC MODE

14-GB

Recording from a

microphone

Connect a stereo microphone (ECM-717,

etc.; not supplied) to the MIC (PLUG IN

POWER) jack. The recorder input

automatically switches to the externally

connected microphone input.

1 Slide MIC SENS to H (high) or L

(low).

2 Slide REC MODE to STEREO.

3 Insert a recordable MD and press

zREC.

For other operations on recording, see

“Recording an MD right away!”

(page 8).

• When you record in monaural, you can record

twice as much as in stereo (page 19)

• When using a plug-in-power microphone, no

battery is needed for the microphone since

power is supplied by the recorder.

If you are using the optional stereo

microphone ECM-717, set the switch on the

microphone to OFF to allow the recorder to

provide power to the microphone.

Notes

• You cannot record through the externally

connected microphone while an optical cable

is connected to the LINE IN (OPTICAL) jack.

The recorder automatically selects the

recorder input in the following order of

priority; optical input, externally connected

microphone input, analog (line) input, and

built-in microphones input.

• The microphone may pick up the operating

sound of the recorder itself. Use the

microphone away from the recorder in such

cases.

to MIC (PLUG IN

POWER)

Stereo

microphone

(not supplied)

REC MODE

MIC SENS

15-GB

Recording from externally connected equipment

The input jack of this recorder works as both digital and analog input jacks. Connect the

recorder to a CD player or a cassette recorder using either digital (optical) input or analog

(line) input. To record, see “Recording with digital (optical) input (optical cable required)”

(page 16) to record using digital (optical) input and “Recording with analog (line) input

(line cable required)” (page 17) to record using analog (line) input.

LINE IN (OPTICAL) jack is for both digital and analog input.

The recorder automatically recognizes the type of line cable and switches to digital or analog input.

Difference between digital (optical) and analog (line) inputs

Note

Track marks may be copied incorrectly:

• when you record from some CD players or multi disc players using digital (optical) input.

• when the source is in shuffle or program play mode while recording using digital (optical) input. In

this case, play the source in normal play mode.

• when recording BS or CS programs through digital (optical) input.

Difference Digital (optical) input Analog (line) input

Connectable

source

Equipment with an digital (optical)

output jack

Equipment with an analog (line)

output jack

Usable cord Optical cable (with an optical or an

optical-mini plug)(page 16)

Line cable (with 2 phono plugs or

a stereo-mini plug)(page 17)

Signal from the

source

Digital Analog

Even when a digital source (such

as a CD) is connected, the signal

sent to the recorder is analog.

Recorded track

numbers

Marked (copied) automatically

• at the same positions as the

source.

• after more than 2 seconds of

blank or low-level segment

• when the recorder is paused

while recording.

You can erase unnecessary marks

after recording. (“Erasing a track

mark”, page 27).

When during synchro-recording only (page 18).

Marked automatically

• after more than 2 seconds of

blank or low-level segment.

• when the recorder is paused

while recording.

You can erase unnecessary marks

after recording (“Erasing a track

mark”, page 27).

Recorded

sound level

Same as the source. Adjusted automatically.

16-GB

Recording with digital

(optical) input (optical cable

required)

Connect to a digital source using an

optical cable (not supplied) to make

digital recordings. Digital recording is

possible even from digital equipment with

different sampling rates, such as a DAT

deck or a BS tuner, using the built-in

sampling rate converter.

1 Slide REC MODE to STEREO.

2 Insert a recordable MD and press

zREC.

“REC” appears in the display, the

REC indicator lights up, and the

recording starts.

3 Play the source sound.

For other operations on recording, see

“Recording an MD right away!”

(page 8).

• When you record in monaural, you can record

twice as much as in stereo (page 19).

• When recording from digital media, track

marks in the original are copied automatically

to the MD.

Notes

• You can make a digital recording only from an

optical type output.

• When recording from a portable CD player,

play it on AC power and disable the anti-skip

function (such as ESP*).

• When recording from a portable CD player,

pause the CD player before doing the

recording procedure.

• Digital output may be disabled on some

portable CD players when the player is not run

on AC power.

• A track mark is added at the point where you

press the XPAUSE button again to resume

recording while pausing recording; thus the

remainder of the track will be counted as a

new track.

∗ Electronic Shock Protection

POC-15AB etc.

(not supplied)

POC-15B etc.

(not supplied)

to LINE IN

(OPTICAL)

Optical

plug

Optical

mini-

plug

CD player, MD

player, digital

amplifier, etc.

Portable CD

player, etc.

zREC

REC

indicator

REC MODE

17-GB

Recording with analog (line)

input (line cable required)

Connect the recorder with a line cable

(not supplied) to make analog recording.

The sound will be sent from the

connected equipment as analog signal but

will be sent recorded digitally on the disc.

1 Slide REC MODE to STEREO.

2 Insert a recordable MD and press

zREC.

“REC” appears in the display, the

REC indicator lights up, and the

recording starts.

3 Play the source sound.

For other operations on recording, see

“Recording an MD right away!”

(page 8).

When you record in monaural, you can record

twice as much as in stereo (page 19).

Note

A track mark is added at the point where you

press the XPAUSE button again to resume

recording while pausing recording; thus the

remainder of the track will be counted as a new

track.

to LINE IN

(OPTICAL)

CD player,

cassette recorder,

etc.(source)

R (red)

Line cable (RK-G129HG,

not supplied)*

to LINE OUT

∗ Use the connecting cords without an

attenuator. To connect to a portable CD

player having a stereo mini-jack, use the

RK-G136HG connecting cord (not

supplied).

zREC

REC indicator

REC MODE

L (white)

18-GB

To start/stop recording

in sync with the source

player

(Synchro-recording)

You can easily make digital recordings of

a digital source on an MD.

Before synchro-recording, make

connections to the digital source with a

digital cable, and insert a recordable MD.

1 Slide REC MODE to STEREO.

2 Slide SYNCHRO REC to ON.

“SYNC” appears in the display.

“SYNC” doesn’t appear if optical

cable is not connected to the LINE IN

(OPTICAL) jack on the recorder.

3 Press zREC.

The recorder stands by for recording.

4 Play the source sound.

The recorder starts recording when it

receives the playing sound.

To stop recording, press xSTOP.

• When you record in monaural, you can record

twice as much as in stereo (page 19).

• You cannot pause manually during synchro-

recording.

• When there is no sound from the player for

more than 3 seconds during synchro-

recording, the recorder goes into the standby

mode automatically. When the sound comes

from the player again, the recorder resumes

synchro-recording. If the recorder is kept in

the standby mode for 5 minutes or longer, the

recorder stops automatically.

Notes

• Do not switch the SYNCHRO REC switch

after step 4. Recording may not be done

properly.

• The REC MODE setting cannot be changed

during synchro-recording.

• Even when there is no recorded sound on the

sound source, there may be cases when

recording does not pause automatically during

synchro-recording due to the noise level

emitted from the sound source.

• If a silent portion is encountered for 2 seconds

or more during synchro-recording, a new track

mark is automatically added at the point

where the silent portion ends.

• Synchro-recording cannot be done if the

connecting cord is not an optical cable, or if

the cable is connected to the MIC (PLUG IN

POWER) jack.

CD players,

etc.

SYNCHRO REC

zREC

REC MODE

OFF

End ¢¢7

Synchro-recording indication

19-GB

Recording in monaural

for double the normal

recording time

For longer recordings, choose to record in

monaural. The recording time becomes

double the normal.

1 Slide REC MODE to MONO.

2 Insert a recordable MD and press

zREC.

For other operations on recording, see

“Recording an MD right away!”

(page 8)

To stop recording, press xSTOP.

Notes

• If you record a stereo source in monaural, the

sounds from left and right will be mixed.

• You may not be able to record in monaural if

the SYNCHRO REC switch is slid to ON. If

you are recording digital input, make sure to

slide the SYNCHRO REC switch to OFF

before you begin recording.

• The MDs recorded in monaural can be played

back only with an MD player/recorder that has

the monaural playing function.

• Sound recorded through digital (optical) input

can be monitored in stereo through

headphones/earphones, etc.

Setting the clock to

stamp the recorded

time

To stamp the date and time on the MD

when you record, you first need to set the

clock.

1 Light up the display by pressing

xSTOP, and then press CLOCK SET

at the button of the recorder.

Use a pointed object.

The digits of the year flash.

If you do not light up the display first,

you will not be able to set the time

even when you press CLOCK SET.

2 Change the current year by pressing

. or >.

To change the digits rapidly, keep

pressing . or >.

3 Press NPLAY to enter the year.

The digit of the month flashes.

4 Repeat step 2 and 3 to enter the

current month, date, hour, and

minute.

When you press NPLAY to enter

the minute, the clock starts operating.

zREC

REC MODE

NPLAY

./>

CLOCK SET

(bottom)

xSTOP

¢¢y 1m 1d

20-GB

If you make a mistake while

setting the clock

Press xSTOP, and set the clock again

from step 1. You can skip a step by

pressing NPLAY.

To display the current time

When the recorder is not operating or

while recording, press DISPLAY

repeatedly until the current time appears

in the display.

To display the time in the 24-

hour system

While setting the clock, press XPAUSE.

To display the time in the 12-hour system,

press XPAUSE again.

Checking the remaining

time or the recording

position

You can check the remaining time, track

number, etc. when recording or during

stop.

1 Press DISPLAY while the recorder is

recording or stopped.

Each time you press the button, the

display changes as follows.

While recording

Track number Elapsed time

Track number Remaining time for

recording

Current date

Appears only when the clock is set.

If you want to date and time stamp the

recording, set the clock in advance.

Current time

DISPLAY

REC indicator

La page charge ...

Sony MZ-B50 Le manuel du propriétaire

Marque: Sony

Modèle: MZ-B50

Catégorie: Joueurs de minidisc

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Sony MZ-B50 Owner's manual
español: Sony MZ-B50 El manual del propietario

Sony MZ-B50 Le manuel du propriétaire

Sony MZ-B50 Le manuel du propriétaire

dans d''autres langues

Documents connexes