Fanimation Benito V2 Le manuel du propriétaire

Marque: Fanimation

Modèle: Benito V2

Catégorie: Ventilateurs ménagers

Taper: Le manuel du propriétaire

Español p. 21

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-888-567-2055, 8 a.m.-5 p.m., EST, Monday-Friday.

ATTACH YOUR RECEIPT HERE AND REGISTER YOUR FAN AT FANIMATION.COM

READ AND SAVE THESE INSTRUCTIONS

Serial Number

Purchase Date Net Weight 20.95 lbs (9.50 kg)

™

MODEL #FP8003B**

BENITO v2 CEILING FAN

Important Safety Instructions

WARNING: To avoid fire, shock and serious personal injury, follow these instructions.

1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly

diagrams.

2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent

power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a

warning device, such as a tag, to the service panel.

3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling

fan before servicing.

4. Do not insert anything into the fan blades while the fan is operating.

5. Do not operate reversing switch until fan blades have come to a complete stop.

Additional Safety Instructions

1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without

blades.

2. All wiring and installation procedures must satisfy National Electrical Codes (ANSI/ NFPA 70-1999) and Local Codes. The

ceiling fan must be grounded as a precaution against possible electrical shock. Electrical installation should be made or

approved by a licensed electrician.

3. The fan base must be securely mounted and capable of reliably supporting at least 35 lbs. (fan and accessories not to

exceed 35 lbs. or 15.88 kgs.). See page 5 of owner’s manual for support requirements. Consult a qualified electrician if in

doubt.

4. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.

5. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not have adequate

electrical knowledge or experience, have your fan installed by licensed electrician.

6. Suitable for use with solid-state speed controls.

WARNING

TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS FAN MUST BE INSTALLED WITH A GENERAL USE,

ISOLATING WALL CONTROL/SWITCH.

WARNING

This product is designed to use only those parts supplied with this product and/or accessories designated

specifically for use with this product. Using parts and/or accessories not designated for use with this product could result in

personal injury or property damage.

WARNING

WARNING: Do not operate this fan with a variable (Rheostat) wall controller or dimmer switch. Doing so could result in

damage to the ceiling fan's remote control unit.

To reduce the risk of personal injury, do not bend the blade bracket (flange or blade holder) when installing the

WARNING

Mount to an outlet box marked acceptable for fan support.

brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.

LIMITED LIFETIME WARRANTY

Extends to the original purchaser of a Fanimation Fan

1. LIMITED LIFETIME MOTOR WARRANTY - If any part of your fan motor fails, due to a defect in materials or workmanship

during the lifetime of the original purchaser, Fanimation will provide the replacement part free of charge, when the defective

fan is returned to our national service center. Proof of purchase is required. Customer shall be responsible for all costs

incurred in the removal or reinstallation and shipping of the product for repairs or replacement.

2. ONE YEAR MOTOR LABOR WARRANTY - If your fan motor fails at any time within one year from the original purchase, due

to defects in materials or workmanship, labor to repair the motor will be provided free of charge at our national service

center. Purchaser will be responsible for labor charges after this one-year period. Customer shall be responsible for all

costs incurred in the removal or reinstallation and shipping of the product for repairs or replacement.

3. If any other part of your fan fails at any time within one year after original purchase, due to a defect in materials or

workmanship, we will repair, or replace, at our option, the defective part free of charge for parts and labor performed at our

national service center.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. If the intentional radiator can be classified as a Class B digital device or a PC

peripheral, then shall include the following or equivalent:

Note: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and the receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Note: For a Class A digital device, statements of 15. 105(a) must be included when appropriate for the device in question.

8. For supply connections, if the conductor of a fan is identified as a grounded conductor, then it should be connected to a

grounded conductor power supply. If the conductor of a fan is identified as an ungrounded conductor, then it should be

connected to an ungrounded conductor power supply. If the conductor of a fan is identified for equipment grounding, then it

should be connected to an equipment grounding conductor.

7. This fan is to be used in dry and damp locations.

1111

8. Under no circumstances may a fan be returned without prior authorization from Fanimation. The receipt of purchase must

accompany authorized returns and must be sent freight prepaid to Fanimation. The fan to be returned must be properly

packed to avoid damage in transit; Fanimation will not be responsible for any damage resulting from improper packaging.

LIMITED LIFETIME WARRANTY

Extends to the original purchaser of a Fanimation Fan

9. It is understood that any repair or replacement is the exclusive remedy available from Fanimation. There is no other

expressed or implied warranty. Fanimation hereby disclaims any and all implied warranties, including, but not limited to

those of merchantability and fitness for a particular purpose to the extent permitted by law. Some states do not allow

limitations on implied warranties. Fanimation will not be liable for incidental, consequential, or special damages arising out

of or in conjunction with product use or performance, except as may otherwise be accorded by law. This warranty gives you

special legal rights and you may also have other rights that vary from state to state.

10.A certain amount of wobble is normal and should not be considered a problem or a defect.

Unpacking Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Energy Efficient Use of Ceiling Fans . . . . . . . . . . . . . . . . . . . . .5

Electrical and Structural Requirements . . . . . . . . . . . . . . . . . .5

How to Assemble Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . .7

How to Hang Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . .9

How to Wire Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . .11

How to Install Your Canopy Housing . . . . . . . . . . . . . . . . . . .12

How to Assemble Your Light Kit or Cap . . . . . . . . . . . . . . . . .

How to Operate Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . .15

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

How to Clean Your Ceiling Fan Blades . . . . . . . . . . . . . . . . . .16

Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Exploded-View Illustration . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Table of Contents

5. This warranty is void and does not apply to damage from improper installation, neglect, accident, misuse, exposure to

extremes of heat or humidity, or as a result of any modification to the original product.

6. All costs of removal and reinstallation of the fan are the sole responsibility of the owner of the fan and not the store that

sold the fan or Fanimation.

7. Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this

warranty.

4. Because of varying climate conditions, this warranty does not cover changes in the finish, including rusting, pitting,

corroding, tarnishing, or peeling.

How to Install Your Remote Control . . . . . . . . . . . . . . . . . . . . 16

How to Assemble Your Fan Blades . . . . . . . . . . . . . . . . . . . . .

1. Check to see that you have received the following parts:

NOTE:

If you are uncertain of part description, refer to

exploded view illustration.

This manual is designed to make it as easy as possible for you to assemble,

install, operate and maintain your ceiling fan

Tools Needed for Assembly

Installed Wire Length Wire Size A.W.G.

Unpacking Instructions

For your convenience, check-off boxes are provided next to each step. As each step is completed, place a check

mark in the box. This will insure that all steps have been completed and will be helpful in finding your place should

you be interrupted.

Before assembling your ceiling fan, refer to section

on proper method of wiring your fan (page 11). If you

feel you do not have enough wiring knowledge or

experience, have your fan installed by a licensed

electrician.

Do not install or use fan if any part is damaged or

missing. This product is designed to use only those

parts supplied with this product and/or any

accessories designated specifically for use with this

product by Fanimation. Substitution of parts or

accessories not designated for use with this product

by Fanimation could result in personal injury or

property damage.

WARNING

Materials

Wiring outlet box and box connectors must be of type

required by the local code. The minimum wire would be a

3-conductor (2-wire with ground) of the following size:

Up to 50 ft. 14

50-100 ft. 12

NOTE:

Place the parts from the loose parts bags in a small

container to keep them from being lost. If any parts are

missing contact your local retailer.

• Motor Assembly

• Hanger Bracket Assembly

Light Plate Assembly

LED Kit

Glass

• Downrod/Hanger Ball Assembly

• Ceiling Canopy

• Canopy Screw Cover Assembly

• Motor Coupling Cover Assembly

• Blade Holder Set

• Blade Set

• Light Plate Assembly

• Glass

• LED Kit

• Light Wire Cap With Screw

• Hand-held Remote

• Receiver Unit

• Steel Cap Assembly

• Hardware bags:

– Sixteen 3/16˝-24 Serrated Head

Screws (blade to blade holder)

– Sixteen Flat Washers

(blade to blade holder)

– Eleven 1/4˝-20 Pan Head Screw

(blade holder to motor)

– Four Wire Connectors

– Balance Kit

– Bag Assembly Safety Cable

Motor Assembly

Downrod/

Hanger Ball

Assembly

Hanger Bracket

Assembly

Ceiling Canopy

Motor Coupling Cover

Assembly

Canopy Screw Cover

Assembly

Hardware Bags

Hand-Held

Remote

Receiver Unit

Blade Holder Set Blade Set

Steel Cap

Assembly

Light Wire Cap

With Screw

• One Phillips head screwdriver

(not supplied)

• One 1/4˝ flat head screwdriver

(not supplied)

• One stepladder

• One wire stripper

• One hex wrench

(not supplied)

Energy Efficient Use of Ceiling Fans

Ceiling fan performance and energy savings rely

heavily on the proper installation and use of the ceiling

fan. Here are a few tips to ensure efficient product

performance.

Using the Ceiling Fan Year Round

Summer Season: Use the ceiling fan in the counter-

clockwise direction. The airflow produced by the ceiling

fan creates a wind-chill effect, making you “feel” cooler.

Select a fan speed that provides a comfortable breeze,

lower speeds consume less energy.

Winter Season: Reverse the motor and operate the ceiling

fan at low speed in the clockwise direction. This produces

a gentle updraft, which forces warm air near the ceiling

down into the occupied space.Remember to adjust your

thermostat when using your ceiling fan - additional energy

and dollar savings could be realized with this simple step!

Electrical and Structural Requirements

Your new ceiling fan will require a grounded electrical

supply line of 120 volts AC, 60 HZ, 15 Amp Circuit.

Electrical code requires use of a fan-rated outlet box to

support the extra weight and motion associated with a

ceiling fan. A fan-rated box will be labeled as such and

typically supports up to a 70lb ceiling fan. Fan-Rated

Outlet Boxes vary in ratings and design. Ensure the

ratings of your ceiling fan outlet box meet the

requirements for the ceiling fan being installed. Figure 1,

Figure 2 and Figure 3 depicts different structural

configurations that may be used for mounting the

outlet box.

Low profile box (Figure 1)

A 1⁄2-in.-deep pancake box is meant to be screwed to a

joist or block. It’s used if only one cable is coming into

the box. It is also available in a saddle-mount

configuration.

CEILING

2" x 4"

CEILING JOIST

OUTLET BOX

Figure 1

Figure 2

2" x 4"

CEILING JOIST

CEILING

OUTLET BOX

Deep box (Figure 2)

A 2-1⁄4-in.-deep box can be attached to blocking

between joists and is roomy enough to handle more

than one cable.

Choosing the Appropriate Mounting Location

Ceiling fans should be installed, or mounted, in the middle

of the room and at least 7 feet from floor to the blade and

18 inches from wall to the blade. If ceiling height allows,

install the fan 8 - 9 feet from floor to the blade for optimal

airflow. Consult your Fanimation Retailer for optional

mounting accessories.

Turn Off When Not in the Room

Ceiling fans cool people, not rooms. If the room is

unoccupied, turn off the ceiling fan to save energy.

Do not operate this fan with a variable (Rheostat) wall

controller or dimmer switch. Doing so could result in

damage to the ceiling fan's remote control unit.

WARNING

Electrical and Structural Requirements (Continued)

If your fan is to replace an existing light fixture, turn

electricity off at the main fuse box at this time and

remove the existing light fixture.

Turning off wall switch is not sufficient. To avoid

possible electrical shock, be sure electricity is

turned off at the main fuse box before wiring. All

wiring must be in accordance with National and

Local codes and the ceiling fan must be properly

grounded as a precaution against possible electrical

shock.

WARNING

Deep box with brace (Figure 3)

Paired with a deep box, this hanger is meant to span

between two joists and takes the place of wooden

blocking.

To avoid fire or shock, follow all wiring instructions

carefully. Any electrical work not described in these

instructions should be done or approved by a

licensed electrician.

WARNING

Figure 3

CEILING JOIST

CEILING

OUTLET BOX

To reduce the risk of fire, electric shock, or personal

injury, mount to outlet box marked acceptable for fan

support of 15.9 kg (35 lbs) or less and use mounting

screws provided with the outlet box. Most outlet boxes

commonly used for the support of luminaires are not

acceptable for fan support and may need to be

replaced, consult a qualified electrician if in doubt.

How to Assemble Your Ceiling Fan

Figure 1

Set Screw

Downrod

Hanger Ball

Figure 2

Figure 4

Hairpin Clip

Clevis Pin

3. Loosen the two set screws and locking nuts in

the downrod support of the motor assembly. Route

the black, white and blue wires and safety cable

through the downrod. (Figure 3)

1. Remove the hanger ball portion from the downrod/

hanger ball assembly by loosening the set screw in the

hanger ball until the ball falls freely down the downrod.

Remove the pin from the downrod, then remove the

hanger ball. Retain the pin and hanger ball for reinstal-

lation in Step 6. (Figure 1)

2. Remove the hairpin clip and clevis pin from the

bottom of the downrod. Retain the pin and clip for

reinstallation in Step 4. (Figure 2)

4. Insert downrod into the downrod support on top of

the motor. Install the clevis pin by aligning the holes

in the downrod support with holes in the downrod.

Secure clevis pin with hairpin clip. Tighten the two set

screws with nuts in the downrod support. (Figure 4)

WARNING

It is critical that the clevis pin in the downrod support

is properly installed and the set screws and nuts are

securely tightened. Failure to do so could result in

the fan falling.

Downrod Support

Figure 3

Black, White, Blue Wires

and Safety Cable

Set Screws

and Nuts (2)

Figure 5

Motor Coupling

Cover

Ceiling Canopy

Canopy Screw

Cover

5. Route wires and safety cable through motor coupling

cover, canopy screw cover and ceiling canopy.

(Figure 5)

Downrod

Set Screws and

Locking Nuts (2)

Hairpin Clip

Clevis Pin

How to Assemble Your Ceiling Fan (continued)

Figure 7

6. Reinstall the hanger ball on the downrod as follows.

Route the black, white and blue wires and safety cable

through the hanger ball. Position the pin through the

two holes in the downrod and align the hanger ball

so the pin is captured in the groove in the top of the

hanger ball. Pull the hanger ball up tight against the

pin. Securely tighten the set screw in the hanger

ball. A loose set screw could create fan wobble.

(Figure 6)

Figure 6

7. Cut off excess lead wire approximately 6 to 9 inches

above top of the downrod. Strip insulation off 1/2 inch

from the end of each lead wire. (Figure 7)

NOTE:

All set screws must be checked, and retightened

where necessary, before installation.

1. Using the

8 ˝x 2˝ lag bolt and flat washer, attach

safety cable to ceiling joist or wood structural member.

The lag bolt will pass through the flat washer, safety

cable loop, and into the building structure (Figure 3).

You will first drill a ¼ pilot hole into the building structure

to prevent splitting or cracking.

2. Securely attach the hanger bracket to ceiling junction

box with #10-32 screws and lock washers acceptable for

ceiling fan support.

NOTE: Ceiling support cable cannot be secured to

junction box only, it must be directly secured to ceiling

joist or structural member using the ⅜ ˝x 2˝ lag bolt and

flat washer. (Figure 3)

3. Make sure the electrical supply wires, including the

hanger bracket grounding wire and safety cable are

pulled through the downrod, between the hanger bracket

and the junction box so that electrical connections can

be made later.

WARNING

The fan must be hung with at least 7´ of clearance from

floor to blades. (Figure 2)

WARNING

The outlet box must be securely anchored and capable

of withstanding a load of at least 35 lbs. Hanger bracket

must seat

rmly against outlet box. If the outlet box is

recessed, remove wallboard until bracket contacts box.

If bracket and/or outlet box are not securely attached,

the fan could wobble or fall.

WARNING

To avoid possible electrical shock, be sure electricity is

turned off at the main fuse box before hanging. (Figure 1)

NOTE: If you are not sure if the outlet box is grounded,

contact a licensed electrician for advice, as it must be

grounded for safe operation.

CAUTION

How to Hang Your Ceiling Fan

Figure 2

Figure 1

Figure 3

AVERTISSEMENT

Assurez-vous que l'alimentation électrique est coupée

au niveau du boîtier à fusibles principal avant de

suspendre le ventilateur afin d'éviter tout risque

d'électrocution. (Figure 1)

AVERTISSEMENT

Le ventilateur doit être suspendu de façon à ce que ses

pales soient au moins à 7 pieds du sol.

(Figure 2)

AVERTISSEMENT

La boîte de sortie doit être solidement ancrée et

acceptable pour supporter un ventilateur de 15,9 kg

(35 livres) au moins. Le support de suspension doit

reposer fermement contre la boîte de sortie. Si la boîte

de sortie est encastrée, retirez le panneau de revêtement

jusqu'à ce que le support entre en contact avec la boîte.

Si le support et/ou la boîte ne sont pas solidement

attachés, le ventilateur risque d'osciller ou même de

tomber.

ATTENTION

Do not connect fan blades until the fan is completely

installed. Hanging fan with blades connected

mayresult in damage to the fan blades.

Ne raccordez pas les pales du ventilateur tant que le

ventilateur n'est pas complètement installé.

L'installation du ventilateur avec les pales

assemblées peut endommager les pales du

ventilateur.

Carefully lift the fan and seat the downrod/hanger ball

assembly on the hanger bracket that was just attached to

the ceiling joist. Be sure the groove in the ball is lined up

with tab on the hanger bracket. (Figure 4)

5. Attach the safety cable to ceiling support cable. Slide

cable clamp onto safety cable (from fan). Place the end

of cable through the loop of ceiling support cable. Pull as

much cable through loop as possible. Feed end of cable

into clamp hole and firmly tighten screw (Figure 4). Cut

off excess safety cable.of

How to Hang Your Ceiling Fan (continued)

HARDWARE USED:

Figure 4

AVERTISSEMENT

Ne pincez pas les fils entre la tige de suspension

descendante et le support de suspension éviter toute

électrocution.

WARNING

To avoid possible shock, do not pinch wires between the

downrod and the hanger bracket.

AVERTISSEMENT

Si vous n'installez pas la languette dans la rainure, vous

risquez d'endommager les fils électriques et de causer

éventuellement une décharge électrique ou un incendie.

WARNING

Failure to seat tab in groove could cause damage to

electrical wires and possible shock or fire hazard.

How to Wire Your Ceiling Fan

MAIN FUSE BOX

Figure 2

Figure 1

Figure 4

Green Wire

from Supply

(Ground)

White Wire

from Supply

White Wire

from Receiver

Green Wire

from Hanger

Bracket (Ground)

Green Wire

from Hanger

Ball (Ground)

Listed

Outlet Box

Household

Supply

Black Wire

from Supply

Black Wire

from Receiver

Receiver

Figure 3

x 6WIRE

CONNECTORS

HARDWARE USED:

ue to

Light

k t

hit

all

Dip Switch

ON DIP

1 2 3 4 5

Receiver Unit

To avoid possible electrical shock, be sure electricity

is turned off at the main fuse box before wiring

(Figure 2).

WARNING

NOTE:

If you are not sure if the outlet box is

grounded, contact a licensed electrician for advice, as

it must be grounded for safe operation.

Check to see that all connections are tight, including

ground, and that no bare wire is visible at the wire

connectors except for the ground wire. Do not

operate fan until the blades are in place. Noise and

motor damage could result.

WARNING

3. After connections have been made, turn leads

upward and carefully push leads into the outlet

box, with the white and green leads to one side

of the box and the black leads to the other side.

(Figure 4)

CAUTION: INCORRECT WIRE CONNECTION WILL

DAMAGE THIS RECEIVER.

2. Connect green wires from hanger bracket and

downrod to bare (ground) wire using wire connector.

Connect black wire from receiver unit marked “AC IN L”

to black supply wire using wire connector. Connect white

wire from receiver unit marked “AC IN N” to white supply

wire using wire connector. Connect white wire from

receiver unit marked “TO MOTOR N” to white wire from

fan using wire connector supplied with receiver unit.

Connect black wire from receiver unit marked “TO

MOTOR L” to black wire from fan using wire connector

supplied with receiver unit. Lastly, connect blue wire

from receiver unit to the blue fan light wire using wire

connector supplied with receiver unit. (Figure 3)

1. To set the code on receiver unit, slide dip switches to

the same positions as set on the remote. (Figure 1)

NOTE: The remote unit has 32 different code

combinations. To prevent possible interference from or to

other remote units, simply change the combination code

in the remote and receiver.

NOTE: Factory setting is all up. Do not use this position.

How to Wire Your Ceiling Fan (continued)

2. Securely attach and tighten the canopy screw cover

over the shoulder screws in the hanger bracket utilizing

the keyslot twist-lock feature. (Figure 1b)

1. Remove one of the two shoulder screws in the

hanger bracket. Loosen the second shoulder screw

without fully removing it. Assemble canopy by

rotating key slot in canopy over shoulder screw in

hanger bracket. Tighten shoulder screw. Fully

assemble and tighten second shoulder screw that

was previously removed. (Figure 1a)

WARNING

To avoid possible fire or shock, make sure that the

electrical wires are completely inside the canopy

housing and not pinched between the housing and the

ceiling.

NOTE: This step is applicable after the neccessary

wiring is completed.

How to Install Your Canopy Housing

Figure 1a

How to Assemble Your Fan Blades

1. Position the blade over the blade holder with threaded

posts showing. Make sure the bottom edge of the blade

is fully seated against the blade holder. With a screwdriver

tighten 3/16˝-24 serrated head screws and flat washers

to secure the blade to the blade holder. (Figure 1)

Do not connect fan blades until the fan is completely

installed. Installing the fan with blades assembled

may result in damage to the fan blades.

CAUTION

Figure 1b

Ceiling

Canopy

x 15

FLAT WASHER

3/16˝-24

SERRATED HEAD

SCREW

HARDWARE USED:

Blade

3/16˝-24 Serrated Head

Screw and Flat Washer

(3 each per blade)

Blade Holder

Figure 1

4. Once the connection has been made, slide the

receiver into the hanger bracket, taking care not to

pinch the wires. (Figure 5)

Receiver

Hanger Bracket

Figure 5

Canopy Screw

Cover

How to Assemble Your Fan Blades (continued)

How to Assemble Your Light Kit or Cap

1. Remove one of the three screws in the support

bracket at the bottom of the motor assembly. Retain

the screw for later and slightly loosen the remaining

two screws. (Figure 1)

2. Assemble the light plate assembly to the support

bracket using the two key slots in the light plate

assembly. Replace the previously removed screw and

securely tighten all three screws. (Figure 2)

3. Remove the three screws in the light plate assembly

and retain the screws for later. (Figure 3)

2. Secure the blade holders to the motor support using

the 1/4˝-20 screws through the holes located on the side

of the motor support. (Figure 2)

NOTE:

Periodically check blade holder hardware and

resecure if necessary.

To reduce the risk of electric shock, disconnect the

electrical supply circult to the fan before installing

light kit.

CAUTION

To reduce the risk of personal injury, do not bend the

blade holders when installing, balancing the blades

or cleaning the fan. Do not insert foreign objects in

between the rotating blades.

WARNING

Blade Holder

1/4˝-20 Screw

(2 per assembly)

Motor Assembly

Figure 2

HARDWARE USED:

x 10

1/4˝-20

SCREWS

Figure 1

Figure 2

Figure 3

Light Plate

Assembly

Light Plate

Assembly

Motor Assembly

4. For use with light kit (A).

Connect the 2 pin connector from the LED kit

to the 2 pin connector from motor assembly.

(Figure 4)

Figure 4

LED Kit

Motor Assembly

How to Assemble Your Light Kit or Cap (continued)

Figure 9

8. For use with steel cap (B).

Assemble the light wire cap to the light kit using the

provided screws and secure all four screws.

(Figure 8)

7. For use with steel cap (A).

Remove the LED assembly from LED kit by remove the

three screws. (Figure 7)

Light Kit

Light Wire Cap

Steel Cap

Figure 6

Figure 8

Figure 5

Figure 7

Glass

9. For use with steel cap (C).

Assemble the steel cap to the light kit by twisting in a

clockwise direction. (Figure 9)

NOTE:

If you have installed your fan with the light kit,

skip as below Steps.

6. For use with light kit (C).

Secure the glass to light kit by twisting in a

clockwise direction. Do not over-tighten. (Figure 6)

5. For use with light kit (B).

Assemble the LED kit to the light plate assembly using

the removed screws in Step 5 and secure all three

screws. (Figure 5)

The light source is designed for this specific

application and can overheat if serviced by untrained

personnel. If any servicing is required, the product

should be returned to an authorized service facility

for examination or repair.

CAUTION

LED Assembly

Light Plate

Assembly

LED Kit

Light Kit

LED Kit

Figure 4

Dip Switch

ON DIP

1 2 3 4 5

Remote

How to Operate Your Ceiling Fan

2. Restore electrical power to the outlet box by turning

the electricity on at the main fuse box. (Figure 2)

Check to see that all connections are tight, including

ground, and that no bare wire is visible at the wire

connectors, except for the ground wire. Do not

operate fan until the blades are in place. Noise and

fan damage could result.

WARNING

1. IMPORTANT: Using a full range dimmer switch

(not included) to control fan speed will damage the fan.

To reduce the risk of fire or electrical shock, do not use

a full range dimmer switch to control the fan speed.

(Figure 1)

WARNING

Do not operate this fan with a variable (Rheostat) wall

controller or dimmer switch. Doing so could result in

damage to the ceiling fan's remote control unit.

3. To make fan operational, install 23A/12V battery

(included) in hand-held remote transmitter, with fan

power off. Then follow the remote code setting

process. (If not used for long periods of time, remove

battery toprevent damage to transmitter). Store the

remote away from excessive heat or humidly.

(Figure 3)

MAIN FUSE BOX

Figure 2

Figure 1

For illustrative purposes only-not

intended to cover all types of controls

4. To set the remote code with a small screwdriver or

ball point pen (neither included), slide dip switches firmly

up or down. (Figure 4)

NOTE: The remote unit has 32 different code

combinations. To prevent possible interference from or to

other remote units, simply change the combination code

in the remote and receiver.

NOTE: Factory setting is all up. Do not use this position.

5. Remote functions: (Figure 5)

12V 23A

Battery (1 pcs)

Figure 3

Figure 5

How to Install Your Remote Control

Figure 1

1. Installing Wall Holder: (Figure 1)

Attach wall holder using the two provided screws.

How to Operate Your Ceiling Fan (continued)

Maintenance

1. Periodic cleaning of your new ceiling fan is the only

maintenance that is needed. When cleaning, use

only a soft brush or lint free cloth to avoid

scratching the finish. Abrasive cleaning agents are

not required and should be avoided to prevent

damage to finish.

Do not use water when cleaning your ceiling fan.

It could damage the motor or the finish and create

the possibility of electrical shock.

CAUTION

Periodic light dusting of the blades is recommended.

A feather duster will work best.

How to Clean Your Ceiling Fan Blades

Avoid using water, cleansers, or harsh rags, which

can warp and ruin the finish.

Reverse Switch Information

Season Rotation Direction Switch Position

Summer Counter-Clockwise Left

Winter Clockwise Right

If airflow is desired in the opposite direction, turn the

fan off and wait for the blades to stop turning. Slide

the coupling cover up to expose the reverse switch.

Then slide the reverse switch on top of motor

assembly to the opposite position and turn fan on

again. (Figure 6)

Figure 6

Coupling Cover

Reverse

Switch

Trouble Shooting

For your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan.

WARNING

Trouble Probable Cause Suggested Remedy

1.FAN WILL

NOT START

1. Check main and branch circuit fuses

or circuit breakers.

2. Check line wire connections to fan

and switch wire connections in the

switch housings.

CAUTION: Make sure main power is

turned off !

3. Make sure reversing switch position is

all the way to one side.

4. Replace with fresh battery.

1. Fuse or circuit breaker blown.

2. Loose power line connections to the

fan, or loose switch wire connections

in the switch housing.

3. Reversing switch in neutral position.

4. Dead battery in remote control.

2.FAN SOUNDS NOISY

1. Attach blades to fan before operating.

2. Check to make sure all screws in

motor housing are snug (not over-

tight).

3. Check to make sure the screws which

attach the fan blade holders to the

motor flywheel are tight.

4. Check to make sure wire connectors

in switch housing are not rattling

against each other or against the

interior wall of the switch housing.

CAUTION: Make sure main power is

turned off !

5. Some fan motors are sensitive to

signals from solid-state variable

speed controls. Solid-state controls

are not recommended, choose an

alternative control method.

6. Tighten screws securely.

7. Tighten set screw securely.

1. Blades not attached to fan.

2. Loose screws in motor housing.

3. Screws securing fan blade holders to

motor flywheel are loose.

4. Wire connectors inside housing

rattling.

5. Motor noise caused by solid state

variable speed control.

6. Screws holding blades to blade

holders are loose.

7. Lower housing support set screw

loose.

3.FAN WOBBLES

EXCESSIVELY

1. Tighten both setscrews securely in

downrod support.

2. Tighten the setscrew in the downrod/

hanger ball assembly.

3. Check to be sure screws which attach

the fan blade holders to the flywheel

are tight.

4. Check to be sure the fan blade

holders seat firmly and uniformly to

the surface of the motor housing.

If holders are seated incorrectly,

loosen the screws and retighten.

5. Tighten the hanger bracket screws to

the outlet box, and secure outlet box.

6. Balance blades using balance kit

provided in hardware bag.

1. Setscrew in downrod support is loose.

2. Setscrew in downrod/hanger ball

assembly is loose.

3. Screws securing fan blade holders to

motor hub are loose.

4. Blade holders not seated properly.

5. Hanger bracket and/or ceiling outlet

box is not securely fastened.

6. Fan blades out of balance.

4.NOT ENOUGH AIR

MOVEMENT

1. If possible, consider using a longer

downrod (not included, you can buy

the longer downrod from

fanimation.com).

Parts List

Model No. FP8003B**

1 Hanger Bracket Assembly with Screws

4 Canopy Screw Cover Assembly APPAC1101D**

ADRAC1-45D**

P8003B01**

APGAC110RDBL

AP672105BL

AP8003B10**

RECAN8003B

APPAC1403D**

AP8003B12**

Light Plate Assembly9

HOW TO ORDER REPAIR PARTS

When ordering repair parts, always give the following information:

• Part Number

• Part Description

• Fan Model Number

Contact your retail store for repair parts.

Before discarding packaging material, be certain all parts have been removed.

** Insert FINISH CODES (Refer to fan model number located on downrod support)

Steel Cap Assembly

TR50015

Receiver Unit

AP8003B13**

AP8003B17

AP8003B16

AMA8003B**

AP8003B15**

HDWFP8003B**

Downrod/Hanger Ball Assembly

Ceiling Canopy

Motor Coupling Cover Assembly

Motor Assembly

Light Kit/Glass Assembly

Blade Holder Set

LED Assembly

Blade Set

Light Wire Cap with Screws

Hand-Held Remote

Hardware Bag Containing:

Wire Connector (4)

Balance Kit

Bag Assembly Safety Cable

Blade Holder Mounting Hardware Bag Containing:

Blade Mounting Hardware Bag Containing:

Serrated Head Screws, 3/16˝-24 (16)

Flat Washers (16)

Pan Head Screws 1/4˝-20 (11)

Reference # Description Part #

NOTE:

The illustration shown is not to scale or its actual configurations may vary.

The Benito v2 - FP8003B**

™

Exploded-View Illustration

2018/01 V.01

10983 Bennett Parkway

Zionsville, IN 46077

Phone: 888-567-2055

Outside U.S.: 317-733-4113

FANIMATION.COM

FAX: 866-482-5215

La page charge ...

Fanimation Benito V2 Le manuel du propriétaire

Marque: Fanimation

Modèle: Benito V2

Catégorie: Ventilateurs ménagers

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Fanimation Benito V2 Owner's manual
español: Fanimation Benito V2 El manual del propietario

Fanimation Benito V2 Le manuel du propriétaire

Fanimation Benito V2 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents