TEAC GF-350 Manuel utilisateur

Marque: TEAC

Modèle: GF-350

Catégorie: Lecteur CD

Taper: Manuel utilisateur

Ce manuel convient également à

MP3 Player GF-350

9A10219000

OWNER’S MANUAL

MANUEL DU PROPRIÉTAIRE

Multi music player / CD recorder

350

ENGLISH

FRANÇAIS

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with

the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination

to avoid injury from tip-over.

13) Unplug this apparatus during lightning

storms or when unused for long periods

of time.

14) Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate normally,

or has been dropped.

Do not expose this apparatus to dripps or splashes.

Do not place any objects filled with liquids, such as vases, on the

apparatus.

Do not install this apparatus in a confined space such as a book

case or similar unit.

The apparatus draws nominal non-operating power from the AC

outlet with its POWER switch in the off position.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

ENGLISH

Optical pickup :

Type : SF-W36FR

Manufacturer : SANYO ELECTRIC CO., LTD.

Laser output : Less than 1 mW (Play) on the objective lens

Less than 5 mW (Record) on the objective lens

Less than 10 mW (Erase) on the objective lens

Wavelength : 783 nm

This product has been designed and manufactured according to

FDA regulations “title 21, CFR, chapter 1, subchapter J, based on

the Radiation Control for Health and Safety Act of 1968“, and is

classified as class 1 laser product. There is not hazardous invisible

laser radiation during operation because invisible laser radiation

emitted inside of this product is completely confined in the

protective housings.

The label required in this regulation is shown

①.

For U.S.A.

①

CAUTION

DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO

EXPOSE THE ELECTRONICS. NO USER SERVICEABLE PARTS

ARE WITHIN!

IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT TEAC FOR A SERVICE REFERRAL. DO NOT USE THE

PRODUCT UNTIL IT HAS BEEN REPAIRED.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY

RESULT IN HAZARDOUS RADIATION EXPOSURE.

WARNING : TO PREVENT FIRE OR SHOCK

HAZARD, DO NOT EXPOSE THIS APPLIANCE

TO RAIN OR MOISTURE.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following

measures:

• Reorient or relocate the equipment and/or the receiving

antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

CAUTION

Changes or modifications to this equipments not expressly

approved by TEAC CORPORATION for compliance will void the

user’s warranty.

For U.S.A.

CAUTION

The product shall not be exposed to dripping or splashing and

that no object filled with liquids, such as vases, shall be placed

on the product.

Do not install this equipment in a confined space such as a

book case or similar unit.

Contents

Thank you for choosing TEAC. Read this manual carefully

to get the best performance from this unit.

Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Before using the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Handling Records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

How to Replace the Stylus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Remote Control Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Parts of the Turntable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Unit Functions and Remote Control . . . . . . . . . . . . . . . . . . . . 10

Basic Operation (Listening to an external source). . . . . . . . . . . 12

Listening to the Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Listening to a Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Listening to a CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Time Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Repeat Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Shuffle Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Programmed Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Before Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Finalize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Erase or Unfinalize a CD-RW . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Before using the unit

Read this before attempting any operations

The nominal temperature should be between 5°C and 35°C

(41°F and 95°F). The CD-RW recorder is more sensitive to

extremes of temperature than ordinary CD players.

Relative humidity should be 30 to 90 degrees noncondensing.

As the unit may become warm during operation, always leave

sufficient space around the unit for ventilation.

< The voltage supplied to the unit should match the voltage as

printed on the rear panel. If you are in any doubt regarding

this matter, consult an electrician.

Choose the installation location of your unit carefully. Avoid

placing it in direct sunlight or close to a source of heat. Also

avoid locations subject to vibrations and excessive dust, heat,

cold or moisture.

Do not place the unit on an amplifier/receiver.

Do not open the cabinet as this might result in damage to the

circuitry or electrical shock. If a foreign object should get into

the unit, contact your dealer or service company.

When removing the power plug from the wall outlet, always

pull directly on the plug, never yank the cord.

< To keep the laser pickup clean, do not touch it, and always

close the disc tray.

< Do not attempt to clean the unit with chemical solvents as

this might damage the finish. Use a clean, dry cloth.

< Keep this manual in a safe place for future reference.

DO NOT MOVE THE UNIT DURING PLAYBACK

During playback, the disc rotates at high speed. Do NOT lift or

move the unit during playback. Doing so may damage the

disc or the unit.

WHEN MOVING THIS UNIT

When changing the unit’s location or packing the unit for

moving, be sure to remove the record or disc. Moving this

unit with the record or disc loaded may result in damage to

this unit. If the unit is to be packed and moved a great

distance, it is also advisable to tighten the turntable transport

locking screw. See Page 9 for instructions.

ENGLISH

Handling Records

< Keep your records away from dust. Keep them in a cool, dry

place.

< To avoid dust and scratches, keep records in their sleeves and

jackets when not in use.

< Store records upright on their edges. Records stored

horizontally will eventually bend and warp.

< Do not expose records to direct sunlight or high humidity and

temperature. Long exposure to high temperatures will warp

the record.

Do not store your records in the trunk of your car. The

temperature in a closed trunk can ruin your collection.

< Store records in an area with stable temperature and

humidity.

< Should the record become dirty, gently wipe the surface in a

circular motion, using a soft anti-static cloth.

Commercial record cleaning systems are available from many

retailers or on-line. TEAC does not endorse any specific

product but, depending on the condition of your record

collection, it may be advisable to look into one of these

systems. Clean records protect your stylus from undue wear.

< Do not touch the record’s grooves. Only handle records, by

the edges or the label, with clean hands. Skin oils from even

clean hands can leave a residue on the record surface that will

gradually deteriorate the quality of your record.

label

grooves

edge

How to Replace the Stylus

The stylus should last about 50 hours under normal use.

However, it is recommended that the stylus be replaced as soon

as you notice a change in sound quality.

Prolonged use of a worn-out stylus may damage the record.

Wear and tear on the stylus will be accelerated when playing 78

RPM records. The higher speed of 78 RPM records wears the

stylus more quickly.

Caution:

Do not remove or bend the stylus.

To avoid injury, do not touch the needle.

Turn off the unit’s power before you replace the stylus.

Keep out of the reach of children.

Handle with care, as the stylus is delicate. Use of a bent or

broken stylus may damage the record and cause the turntable

to malfunction.

Do not expose stylus to extreme heat.

Contact a qualified repair company if you experience difficulty

in changing the stylus.

Removing old stylus

1. Set a screwdriver at the tip of the stylus and push down to

the direction “A”.

2. Remove the stylus by pulling it forward and down.

The replacement stylus for this GF-350 is a STL-153. Please

contact TEAC Parts at (323) 726-0303, extension 840 to order.

Or call our automated Service Agency Locator at: (800) 447-

TEAC for the closest authorized repair company that can

replace the stylus for you.

Guide Pins (inside)

Installing a new stylus

1.Hold the tip of the stylus and insert the other edge by

pressing in the direction “B”.

2. Push up in the direction “C” until it locks at the tip.

How to remove the disc How to hold the disc

Always place the disc on the disc tray with the label side

uppermost. (Compact discs can be played or recorded only on

one side.)

To remove a disc from its storage case, press down on the

center of the case and lift the disc out, holding it carefully by

the edges.

Never use such chemicals as record sprays, antistatic sprays or

fluid, benzine or thinner to clean the discs. Such chemicals

will do irreparable damage to the disc’s plastic surface.

Discs should be returned to their cases after use to avoid dust

and scratches that could cause the laser pickup to “skip.”

< Do not expose discs to direct sunlight or high humidity and

temperature for extended periods. Long exposure to high

temperatures will warp the disc.

Do not play any disc that is warped, deformed or damaged.

Playing such discs may cause irreparable harm to the playing

mechanisms.

CD-R and CD-RW discs are more sensitive to the effects of

heat and ultraviolet rays than ordinary CDs. It is important

that they are not stored in a location where direct sunlight

will fall on them, and away from sources of heat such as

radiators or heat-generating electrical devices.

Printable CD-R and CD-RW discs aren’t recommended, as the

label side might be sticky and damage the unit.

< Do not stick papers or protective sheets on the discs and do

not use any protective coating spray.

< Use a soft oil-based felt-tipped pen to write the information

on the label side. Never use a ball-point or hard-tipped pen,

as this may cause damage to the recorded side.

Never use a stabilizer. Using commercially available CD

stabilizers with this unit will damage the mechanisms and

cause them to malfunction.

Do not use CDs with an irregular shape (octagonal, heart

shaped, business card size, etc.). CDs of this sort can damage

the unit:

If you are in any doubt as to the care and handling of a CDR/

CD-RW disc, read the precautions supplied with the disc, or

contact the disc manufacturer directly.

< Should the disc become dirty, wipe the surface radially (from

the center hole outward towards the outer edge) with a soft,

dry cloth:

Please use CD, CD-R and CD-RW discs bearing the

“DIGITAL AUDIO” mark.

This unit CANNOT RECORD CD-R and CD-RW discs

designed for computer systems.

In this manual, although we refer to “CD-R” and CD-RW”

discs, we always mean “CD-R Digital Audio” and “CD-RW

Digital Audio”, even when this is not explicitly stated.

CD-R and CD-RW discs designed for computer systems and

properly recorded by a computer are playable, but this unit

cannot record, finalize nor erase them.

Depending on the quality of the disc and/or the condition of

the recording, some CD-R/CD-RW discs may not be playable.

< Copy-protected discs and other discs which do not conform

to the CD standard may not play back correctly in this player.

If you use such discs in this unit, TEAC Corporation and its

subsidiaries cannot be responsible for any consequences or

guarantee the quality of reproduction. If you experience

problems with such non-standard discs, you should contact

the producers of the disc.

CD-R CD-RW

Discs

ENGLISH

About CD-R and CD-RW discs

CD-R discs can be recorded once only. Once they have been

used for recording, they cannot be erased or re-recorded.

However, if space is available on the disc (and the disc has not

been finalized), additional material can be recorded.

By contrast, a CD-RW disc can be used in much the same way

as a CD-R disc, but the last track or tracks recorded can be

erased, and the space on the disc can be re- used for other

recordings.

However, you should note that an audio CD created using a

CD-RW disc may not play back satisfactorily on every audio

CD player.

CD-R, by contrast, may be played satisfactorily on the majority

of audio CD players.

Finalizing

Although audio data may be written on a CD-R or CD-RW

disc, a standard CD player will not be able to play back the

audio until a final table of contents (TOC) has been written at

the start of the disc.

The process of writing this table of contents is known as

“finalizing”. Once this has been done, no further data can be

written to the disk.

Note that a CD-RW disc that has been finalized can be

“unfinalized”. This allows further tracks to be recorded to the

disc, provided that there is space on the disc.

Repeat, shuffle and programmed playback don’t work with

unfinalized (NO TOC) discs.

Recordable discs

In this manual, we use the term “recordable” disc to describe

a CD-R or CD-RW disc that has not been finalized, and has

enough space to record.

Remote Control Unit

Remove the battery compartment cover.

Insert two “AA” (R6, SUM-3) dry batteries. Make sure that the

batteries are inserted with their positive “+

” and negative

“_

” poles positioned correctly.

Close the cover.

Battery Replacement

If the distance required between the remote control unit and

main unit decreases, the batteries are exhausted. In this case

replace the batteries with new ones.

Precautions concerning batteries

Be sure to insert the batteries with correct positive “+” and

negative “_

” polarities.

Use batteries of the same type. Never use different types of

batteries together.

Rechargeable and non-rechargeable batteries can be used.

Refer to the precautions on their labels.

When the remote control unit is not to be used for a long

time (more than a month), remove the batteries from the

remote control unit to prevent them from leaking. If they leak,

wipe away the liquid inside the battery compartment and

replace the batteries with new ones.

Do not heat or disassemble batteries and never dispose of old

batteries by throwing them in a fire.

The provided Remote Control Unit allows the unit to be

operated from a distance.

When operating the remote control unit, point it towards the

REMOTE SENSOR on the front panel of the unit.

Even if the remote control unit is operated within the effective

range, remote control operation may be impossible if there

are any obstacles between the unit and the remote control.

If the remote control unit is operated near other appliances

which generate infrared rays, or if other remote control

devices using infrared rays are used near the unit, it may

operate incorrectly. Conversely, the other appliances may

operate incorrectly.

Battery Installation

Connections

CD Player, Cassette Tape Deck, etc.

AUDIO OUT

CAUTION:

< Switch off the power to all equipment before making connections.

Read the instructions of each component you intend to use with this unit.

Be sure to insert each plug securely. To prevent hum and noise, avoid bundling the

signal interconnection cables together with the AC power cord.

FM antenna

While in FM mode, tune in an FM station and extend the lead to find the best position

for the reception. This antenna may need to be repositioned if you move your unit to a

new location.

AUX IN jacks

You can connect a CD player, cassette tape deck, etc. to this unit.

Connect the component with RCA pin cords. Make sure to connect the white plug to

the white jacks (Left) and the red plug to the red jacks (Right).

AC Power Cord

Plug this AC power cord into an AC wall socket.

ENGLISH

turntable

screw fixing the turntable for transportation

Before use, completely loosen the screw by turning it

clockwise with a coin or screwdriver.

When you transport the unit, turn the screw counterclockwise

to secure the turntable.

cue-lever

Use this lever to lift the tone arm.

tone arm holder

speed selector

tone arm

45 RPM adaptor

To Open:

1 Lift the turntable cover all the way up until it stops.

2. Lower the cover slowly until the latch engages.

3. The cover will now stay open. If the latch does not engage,

repeat these steps again.

To Close:

1. Lift the cover all the way up until it stops.

2. The latch should disengage and you may now slowly lower

the cover.

3. Make sure you grasp the cover by the edges to avoid pinching

your fingers as it closes.

Parts of the Turntable

How to open/close the turntable cover

Before use, slide the stylus

guard (grayish smoke

colored plastic cover) up.

Unit Functions and Remote Control

A C HE FB GD

S R O L

K II

P N J

ENGLISH

POWER

Press this button to turn the unit on or off.

PHONO/AUX, FM/AM, CD

Press the PHONO/AUX button and select PHONO to play a

record.

Press the PHONO/AUX button and select AUX to listen to the

external source connected to the AUX IN jacks.

Press the FM/AM button to listen to the radio.

Press the CD button to play a CD.

Remote Sensor

When operating the remote control unit, point it towards the

REMOTE SENSOR.

Display panel (frequency)

When the unit is on, this display will light.

TRACK INCREMENT

During recording, use this button to divide tracks.

RECORD

Use this button to enter record pause mode.

Display

TUNED indicator

Lights when a station is correctly tuned in.

Speakers (stereo)

CD operation buttons

STOP (H

)

Use this button to stop playback or recording.

PLAY (y)

Use this button to start playback, recording, finalizing and

erasing.

PAUSE (J)

Use this button to pause playback or recording.

OPEN/CLOSE

In CD or PHONO/AUX mode, use this button to open and

close the disc tray.

This button don’t work in FM/AM mode.

VOLUME

Turn this knob to adjust the volume.

Disc Tray

The equipment draws a nominal amount of power from

the AC outlet even with its POWER switch in the OFF

position.

MUSIC SKIP (.//)

In CD mode, use these buttons to skip tracks.

Hold down these buttons to search for a part of a track.

REC LEVEL

In record pause mode, use this knob to adjust the recording

level.

FINALIZE

Use this button to finalize a CD-R/CD-RW disc.

ERASE

Use this button to erase or unfinalize a CD-RW disc.

TUNING

In FM/AM mode, turn this knob to tune in a station.

PHONES

For private listening, first reduce the volume level to

minimum. Then insert the plug from your headphones into

the PHONES jack, and adjust the volume by turning the

VOLUME knob. The sound from speakers will be cut off while

the headphones are plugged in.

MANUAL/AUTO REC

Use this button to select the mode of track number

assignment.

PROGRAM

In CD mode, use this button to program tracks.

CLEAR

In CD mode, use this button to clear programmed tracks.

REPEAT

In CD mode, use this button to select a repeat mode of CD.

DISPLAY

In CD mode, use this button to change the display.

SHUFFLE

In CD mode, use this button for shuffle playback.

Note:

To simplify explanations, instructions refer to names of

buttons and controls on the front panel, making no mention

of the use of remote control unit.

Press the POWER switch to turn the unit on.

Select a source by pressing the corresponding button.

< To listen to an external source connected to AUX jacks, select

AUX by pressing the PHONO/AUX button once or twice.

Play the source, and adjust the volume by turning the

VOLUME knob.

Basic Operation Listening to the Radio

Select FM or AM using the FM/AM button.

Turn the TUNING knob to tune in a station.

1 3

If the reception is poor

AM broadcast

Turn around the unit to find the best position for AM

stations.

FM broadcast

Extend and turn around the FM antenna so that you can

receive the stations clearly.

The TUNED indicator lights when a station is correctly tuned

in.

The STEREO indicator lights when an FM stereo broadcast is

tuned in.

ENGLISH

Listening to a Record 1

Before use, completely loosen the transportation screw by

turning it clockwise with a coin.

Slide the stylus guard (grayish smoke colored plastic cover) up.

Press the PHONO/AUX button once or twice to select

PHONO.

Select the speed.

Put the record on the turntable.

When playing a 45 RPM record, use the included adaptor.

Gently push the clamper to the right to release the tone

arm.

Raise the cue lever to lift the tone arm off the tone arm

support.

tone arm

cue lever

clamper

1 2

Gently open the dust cover.

Be careful not to pinch your finger.

transportation screw

adaptor

Listening to a Record 2

When the playback has been finished, the tone arm

automatically returns to the tone arm holder and the rotation

stops.

To stop playback manually, slightly lift the tone arm using the

cue lever and return it to the tone arm holder.

Move the tone arm gently to the edge of the record (or

the starting point of a track).

The turntable will begin to turn.

Gently lower the tone arm by slowly releasing the cue

lever.

You can lower the tone arm manually if the cue lever has not

been raised.

< Playing records with the dust cover down will prevent dust

from settling on the turntable.

Please do not place anything on top of the turntable

cover, especially while playing a record.

tone arm

cue lever

ENGLISH

Listening to a CD 1

Press the OPEN/CLOSE button (L).

Place a disc on the tray with the printed label face up.

< Never place more than one disc on the tray.

The disc must be placed in the center of the disc tray. If the

disc is not correctly loaded, it may not be possible to open the

tray again once it has closed, so you should ensure the disc is

always centered on the tray.

Do not force the tray by hand during opening and closing

operations.

Press the OPEN/CLOSE button (L) to close the tray.

Press the PLAY button (y) to start playback.

Disc playback starts from the first track, and the PLAY

indicator (y

) lights on the display.

If you load the disc, and then press the PLAY button without

having first closed the disc tray, the disc tray closes and

playback starts.

Press the CD button.

“

” blinks for a few seconds.

When no disc is set, “nOdISC” appears on the display.

It takes a few seconds for the unit to load the disc. No

buttons will work during loading. Wait until the total number

of the tracks and the total play time of the disc are displayed.

2 43

1 5

disc type indicator

total play time of the disctotal number of the tracks

< The disc type indicator shows the type of disc currently

loaded.

CD:

A commercial pre-recorded CD

CD-R:

A finalized CD-R

CD-RW:

A finalized CD-RW

NO TOC CD-R:

A CD-R which has yet to be finalized

NO TOC CD-RW:

A CD-RW which has yet to be finalized

blank:

No disc or unreadable disc

During playback, repeatedly press the SKIP button

or/) until the desired track is found. The selected

track will be played from the beginning.

In the stop mode, press the SKIP button (.or/)

repeatedly until the track you want to listen to is found, and

press the PLAY button (y

) to start playback from the

selected track.

< When the . button is pressed during playback, the track

being played will be played from the beginning. To return to

the beginning of the previous track, press the .

button

twice.

To suspend playback temporarily

(pause mode)

Press the PAUSE button (J) during playback. Playback stops

at the current position.

To resume playback, press the PLAY button (y

) or the

PAUSE button (J

To stop playback

Press the STOP button (H) to stop playback.

To skip to the next or a previous track

Search for a part of a track

During playback, hold down the SKIP button (.or/)

and release it when the part you want to listen to is found.

Listening to a CD 2 Time Display

Each time the DISPLAY button is pressed, the display changes as

follows:

B A

C D

Unfinalized CD-R/CD-RW, stopped

During recording

CD/CD-R/CD-RW playback

total number of the tracks total play time of the disc

remaining recording time of the disc

elapsed recording time of the track

remaining recording time of the disc

elapsed time of current track

time remaining for current track

total elapsed time of the disc

time remaining for the disc

ENGLISH

Shuffle Playback

Each time the REPEAT button is pressed, the repeat mode is

changed as follows:

REPEAT ALL (Repeat All the Tracks)

Press the REPEAT button once during playback.

All the tracks of the disc will be played repeatedly.

REPEAT 1 (Repeat one track)

Press the REPEAT button twice during playback.

The track being played will be played repeatedly. If you press

the MUSIC SKIP button and select another track, the track

you selected will be played repeatedly.

It is also possible to select a track to be repeated in the stop

mode. Press the REPEAT button twice and then select the

track number by pressing the MUSIC SKIP button. Press the

PLAY button to start playback.

If one of the following buttons is pressed, repeat mode will

be cancelled:

OPEN/CLOSE, POWER, FM/AM, PHONO/AUX

Repeat playback works with finalized discs only.

Repeat Playback

The tracks can be played randomly. Press the SHUFFLE button

during playback. (In the stop mode, press the SHUFFLE button

and the PLAY button.)

When the shuffle playback of all the tracks has been finished,

the unit stops and the shuffle playback mode is cancelled.

If you press the / button during shuffle playback, next

track will be randomly selected and played. If you press the

button, the currently played track will be played from

the beginning. A track cannot be replayed during shuffle

playback.

Shuffle playback doesn’t work during programmed playback.

If one of the following buttons is pressed, shuffle mode will

be cancelled:

SHUFFLE in the stop mode, OPEN/CLOSE, POWER, FM/AM,

PHONO/AUX

< Shuffle playback works with finalized discs only.

REPEAT ALL REPEAT 1

(off)

Programmed Playback

The track is programmed, and “P-02” is displayed.

Repeat step and to program more tracks.

You can program up to 32 tracks.

To cancel the program mode, press the STOP button (H).

When the selection of track numbers has been finished,

press the PLAY button (y

) to start program playback.

Up to 32 tracks can be programmed in the desired order.

Insert a disc and select “CD” before beginning programming.

Shuffle playback does not work during programmed

playback.

Programmed playback works with finalized discs only.

Press the PROGRAM button in the stop mode.

“PROGRAM” indicator blinks, and “P-01” appears on the

display.

Press the MUSIC SKIP button (. or /) to select a

track.

Press the PROGRAM button.

track number

ENGLISH

To add a track to the end of the program

In the stop mode, press the PROGRAM button.

Select a track number by pressing the MUSIC SKIP button,

and then press the PROGRAM button.

The track is added to the end of the program.

To delete the last track from the program

In the stop mode, press the CLEAR button to delete the last

track from the program.

To clear the program

If one of the following buttons is pressed, the programmed

contents will be cleared:

OPEN/CLOSE, POWER, FM/AM, PHONO/AUX,

STOP in the stop mode

To check the programmed order

In the stop mode, press the MUSIC SKIP button repeatedly to

show the track numbers that have been stored in memory.

Before Recording

Before you start recording, make sure that you understand

the following points:

< The unit requires Digital Audio CD-R or CD-RW media for

recording. Computer CD-R or CD-RW discs do not work with

this unit.

Once you have recorded on a CD-R disc, the data cannot be

erased from it.

< You can add tracks to an unfinalized recordable disc. Once

finalized, a CD-R disc is “fixed” and behaves in the same way

as a CD. Finalized CD-RW discs, however, can be unfinalized,

erased and re-recorded.

Due to the system restrictions of CD, a track cannot be less

than four seconds in length, and there can be a maximum of

99 tracks on an audio CD.

If the STOP button or PAUSE button is pressed within four

seconds from the beginning of a track, the unit continues to

record no signal and stops when the track’s length reaches

four seconds.

When the recording is finished, “REC” and “- - - - - -” blink

for a few seconds, and the unit then goes into stop mode. Do

not apply shock or vibration to the unit during recording.

If the disc reaches the end during recording, the unit will start

a fade-out over a few seconds.

When the fade-out has finished, the unit finalizes the disc

automatically and stops.

If the disc reaches the end of the 99th track during recording,

the unit finalizes the disc automatically and stops.

< The recording time of a track may differ slightly from the

original one.

Serial Copy Management System

This unit is in compliance with the Serial Copy Management

System standard. This standard has been established to

restrict digital-to-digital copying to only the first generation.

The basic rules governing this system are as follows:

Rule 1

A digital recording is possible from a digital source such as a

CD, DAT or MD onto a recordable CD-R, CD-RW, MD or DAT

through a digital input connection. However, further digital

to- digital recording is prohibited for the second and later

generations.

Rule 2

When an analog source such as an analog disc or FM

broadcast is digitally recorded by using a CD-R, CD-RW, MD

or DAT, this recorded source can be digitally recorded on

another CD-R, CD-RW, MD or DAT. However, further digital

copying is prohibited.

Recording

When the MANUAL/AUTO REC button is pressed once, the

current mode is displayed. Press the MANUAL/AUTO REC

button repeatedly to select any other mode.

– – (MANUAL)

The unit doesn’t divide tracks.

Use the TRACK INCREMENT button to divide tracks.

MANUAL is recommended for recording an analog source

such as a record.

–20db, –30db or –40db (AUTO REC)

The unit will automatically insert a track division in the

recorded material when the sound level has dropped below

the threshold for more than 2 seconds, and sound has re-

started.

“–20db” takes a louder signal to trigger the track increment.

“–40db” means that a relatively quiet signal will trigger the

track increment. “–40db” is suitable for recording a noiseless

source such as a CD.

AUTO REC may not work properly with analog sources that

contain low-level noises.

The AUTO TRACK indicator lights when –20dB, –30dB or

–40dB is selected.

< The default setting is MANUAL (off). When the unit is turned

on, or when the disc tray is opened, the setting is

automatically reset to MANUAL (off).

The MANUAL/AUTO REC button doesn’t work during

recording or in the record pause mode.

Press the RECORD button.

Audio from the PHONO or AUX sources can be recorded on

the CD recorder.

Press the PHONO/AUX button once or twice to select

the source to be recorded.

To record a record, select PHONO.

To record an external source connected to the AUX IN jacks,

select AUX.

Load a recordable CD-R or CD-RW disc into the unit.

Press the OPEN/CLOSE button (L), place a disc on the disc

tray with the printed label side up, and then press the

OPEN/CLOSE button (L

) to close the disc tray.

Make sure “NO TOC” and “CD-R” (or “CD-RW”) indicators

lights on the display, or the RECORD button in step will not

work.

225

1 4 7

Select the mode of track number assignment using the

MANUAL/AUTO REC button of the remote control unit.

The red indicator on the RECORD button lights.

“REC” and J

indicators on the display will light, and the unit

enters record pause mode.

La page charge ...

TEAC GF-350 Manuel utilisateur

Marque: TEAC

Modèle: GF-350

Catégorie: Lecteur CD

Taper: Manuel utilisateur

Ce manuel convient également à

MP3 Player GF-350

Télécharger le PDF

rapport

dans d''autres langues

English: TEAC GF-350 User manual

TEAC GF-350 Manuel utilisateur

Ce manuel convient également à

TEAC GF-350 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents