Flex Trinity Mode d'emploi

Taper
Mode d'emploi
In-cab Advanced Trinity AG / FT-700 / FT-750
Key Value Proposition
Advanced Capabilities
Internal and External Antennas
1
Applications
Heavy Truck
School Buses
Capabilities
Motion Detection
High Frequency Tracking
Vehicle Diagnostics (ISO-15765,
J1939)
Ignition Detection
Ignition On Tamper Detection
Starter Disable (via relay)
Operator ID (1-wire)
Digital inputs / outputs
Future Capabilities
Driver Behavior
ELD tablet communication
Camera video upload
FLEX CONFIDENTIAL DO NOT DISCLOSE
In-cab Advanced Trinity AG
2
Location
GPS (multi-constellation)
Assisted acquisition: 2s (via cloud)
Acquisition Sensitivity: -160dBm (1)
Tracking Sensitivity: -167dBm (2)
Internal Sensors
9-axis IMU
System temperature
Battery level
Internal Antennas
Cellular primary and secondary
GPS, Bluetooth, WiFi
External Connectors
Cellular primary
GPS
USB
Power in (6-48VDC)
Power out (2.5W)
1-Wire
ADC (48V) x 2
Digital Input x4
Digital Output x 3
Ignition Detection
CAN 2.0B x1 (ISO-15765 or J1939)
CAN 2.0B or FD x1 (ISO-15765 or J1939)
RS-232 x2
ISO-9141 (K line for Tachometer)
J1708 (Firmware support TBC)
Battery
1.3Ah
User Interface
Power button, 5 LEDs
Buzzer
Global Cellular Connectivity
FT-700 Standard SKU:
4G (Cat M/NB-IoT) Global Bands
2G: 850,900,1800,1900
Local Area Connectivity
WiFi: 802.11 b/g/n (2.4GHz) station & softAP (6)
BLE: 5.0 (master, slave, LE data packet length)
USB: mass storage (host), ACCM (client)
Operating Temperature
Powered: -40˚C – 70˚C
Battery: -20˚C – 60˚C
Charging: 0˚C – 45˚C
Housing
Industrial grade Polycarbonate (PC)
Ingress Protection (IP): 4X
Security
Secure boot
TLS/SSL
FIPS 140-2 (Optional)
Certifications
FCC, IC, CE, PTCRB, RCM
Environmental
RoHS, Reach, SAEJ1455 [Thermal Shock (4), Humidity
(5), Mechanical Vibration, Mechanical Shock,
Electrostatic Discharge]
Dimensions
7.3” x 3.23” x 1.22” (184mm x 82mm x 31mm)
Weight
TBC (1) (2) Based on GPS chipset specification
(4) (5) Inside operating temperature range
(6) For telemetry & ELD applications only; not intended for generic
hotspot capability; throughput limited to ~20KBps (TBC)
FLEX CONFIDENTIAL DO NOT DISCLOSE
FCC Regulations:
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This device has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiated radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by the party responsible for
compliance could void the user‘s authority to operate the equipment.
RF Exposure Information
This device meets the governments requirements for exposure to radio waves.
This device is designed and manufactured not to exceed the emission limits for exposure
to radio frequency (RF) energy set by the Federal Communications Commission of the
U.S. Government.
This device complies with FCC radiation exposure limits set forth for an uncontrolled
environment. In order to avoid the possibility of exceeding the FCC radio frequency
exposure limits, human proximity to the antenna shall not be less than 20 cm
during normal operation.
ISED Notice
This device complies with Innovation, Science and Economic Development
Canada license-exempt RSS standard(s). Operation is subject to the following two
conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR Innovation, Sciences et Développement
économique Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en
This device complies with the Canadian ICES-003 Class B specifications. CAN ICES-003(B)/
NMB-003(B)
ISED RF Exposure Statement
This device complies with ISED RSS-102 RF exposure limits set forth for an uncontrolled
environment. In order to avoid the possibility of exceeding the IC RSS-102 RF exposure
limits, human proximity to the antenna shall not be less than 20cm (7.87 inches) during
normal operation.
Cet appareil est conforme aux limites d'exposition aux rayonnements de la CNR-102
définies pour un environnement non contrô. Afin d'éviter la possibilité de dépasser les
limites d'exposition aux fréquences radio de la CNR-102, la proximité humaine à l'antenne
ne doit pas être inférieure à 20 cm (7.87 pouces) pendant le fonctionnement normal.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Flex Trinity Mode d'emploi

Taper
Mode d'emploi

dans d''autres langues