ADT RC845 Guide d'installation

ADT
Marque
ADT
Modèle
RC845
Catégorie
Des caméras de sécurité
Taper
Guide d'installation
ADT Interactive Solutions: Control & Pulse
RC845 Wireless FHD Indoor Camera
Quick Installation Guide
ADT RC845 FHD Indoor Camera
Quick Installation Guide
RC845 Indoor FHD Camera Installation Guide
2
Table of Contents
1 Introduction .................................................................................3
1.1 Feature Overview ................................................................ 3
1.2 Physical Details: Front and Rear Panels ........................... 3
1.3 Packaging Contents ............................................................ 4
2 Basic Setup .................................................................................5
2.1 Assembling the Camera ..................................................... 5
2.2 Power-Up ............................................................................. 5
2.3 Final Steps .......................................................................... 5
3 ADT Control Enrollment ..............................................................6
3.1 Using Soft AP to Enroll Camera .......................................... 6
4 ADT Pulse Enrollment .................................................................9
4.1 Using WPS PIN to Enroll Camera ....................................... 9
5 Wall Mounting .......................................................................... 15
5.1 Smart IR and Mounting Suggestion ................................ 16
6 Troubleshooting ....................................................................... 17
6.1 If the Camera Continually Goes Offline .......................... 17
7 Appendix ................................................................................... 18
7.1 Technical Specifications .................................................. 18
7.2 Regulatory Approvals ....................................................... 19
7.2.1 Federal Communication Commission Interference
Statement ....................................................................... 19
7.2.2 Industry Canada Statement ................................. 20
©2019 ADT LLC dba ADT Security Services. All rights reserved. ADT, the ADT logo,
1.800.ADT.ASAP and the product/service names listed in this document are marks and/or
registered marks. Unauthorized use is strictly prohibited. RC845 (11/19)
Property of ADT, LLC. Information accurate as of published date and is provided “as is”
without warranty of any kind.
ADT RC845 FHD Indoor Camera
Quick Installation Guide
RC845 Indoor FHD Camera Installation Guide
3
1 Introduction
This section provides information about the RC845 Indoor Day/Night Full
High Definition (FHD) Camera's features, components and capabilities.
1.1 Feature Overview
The RC845 is an indoor day/night camera with FHD resolution and 802.11ac
Wi-Fi connectivity intended for use with both ADT Control® and Pulse®.
• Standalone Design. The camera is a standalone system with built-in CPU
and video encoder. It requires only a power source and a connection to the
network (customer router for Control or ADT Pulse gateway).
• Dual Video Support. The RC845 supports H.264 and MJEPG video
compression.
• Day/Night Switch. With the day/night switching feature, you can view and
record images even at night.
• IR LED Support. The two infrared (IR) LEDs can provide illumination for up to
5 meters/16 feet, providing superior video quality under low-light conditions.
• 802.11ac Support. The 802.11ac standard provides backward
compatibility with the 802.11 b/g/n standards.
• Supports Soft AP and WPS PIN Enrollment. Software-enabled Access Point
(Soft AP) connectivity is used on the Control platform. Wi-Fi Protected Setup
PIN (WPS PIN) uses a push button and PIN to connect to the Pulse platform.
• Wireless Network. The RC845 is connected to the network wirelessly.
• Two-Way Audio. The RC845 has a speaker and microphone for two-way
conversations and echo cancellation.
1.2 Physical Details: Front and Rear Panels
ADT RC845 FHD Indoor Camera
Quick Installation Guide
RC845 Indoor FHD Camera Installation Guide
4
Description
Connect the supplied 12V power adapter. Do not use
other power adapters; doing so may damage the camera.
Off: Unit does not have power
On: (Blue) Unit is booting up then LED will blink blue ten
times
Blinking: (Green/Amber) The power LED will blink
green/amber after initial startup is completed. This
indicates that the Soft AP OR WPS PIN mode is ready.
On: (Green) Camera is connected to Network.
Blinking: (Green) Camera has lost connection to the
Network
Blinking: (Amber) Unit is in WPS PIN mode and/or the
WPS connection is in progress.
On: (Amber) If the LED is on for 5 seconds and then turns
off, the WPS function has failed.
This button serves two functions on the camera.
WPS PIN Mode: When pressed and held for 5 seconds
during the Pulse enrollment process, the camera creates
an encrypted secure wireless connection.
Reset: When pressed and held for 15 seconds, the
camera reboots and settings are restored to default
values.
The lens is fixed and cannot be adjusted. Please ensure
that the lens cover remains clean of dust and debris.
Built-in Infrared LEDs for Night Time Illumination
This is a hardware sensor to detect daylight level or lux.
Built-in Microphone with echo cancelation
Built-in Speaker (1W)
Built-in Micro SD Card Slot for future enhancements
Note: As the microSD card slot is not currently functional, please do not
remove this protective cover.
1.3 Packaging Contents
ADT RC845 FHD Indoor Camera
Quick Installation Guide
RC845 Indoor FHD Camera Installation Guide
5
2 Basic Setup
This section provides information on how to assemble and configure the
RC845 Indoor FHD Camera for enrollment.
2.1 Assembling the Camera
• Temporarily locate the camera close to the computer for enrollment.
• Attach the camera stand to the camera and connect the power cable.
• Screw/attach the camera onto the camera stand.
2.2 Power-Up
• Connect the 12V power adapter to the camera and power up near the
location where you will be performing the enrollment.
Caution: Use the power adapter provided. Using a different
power adapter may result in hardware damage.
2.3 Final Steps
• Check LED Status
- The LED lights up solid blue then blinks ten times during startup,
which takes about 30 seconds. After startup is completed, and
prior to enrollment, the power LED blinks green/amber.
• Enroll the Camera
- The process for enrolling the camera on Control is described in
Section 3: ADT Control Enrollment.
- The process for enrolling the camera on Pulse is described in
Section 4: ADT Pulse Enrollment.
ADT RC845 FHD Indoor Camera
Quick Installation Guide
RC845 Indoor FHD Camera Installation Guide
6
• Mounting the Camera
- Mount the camera in its final permanent location. For mounting on
a wall using the mounting bracket, see Section 5: Wall Mounting.
3 ADT Control Enrollment
This section provides instructions for wirelessly enrolling the RC845 Indoor
FHD Camera onto the ADT Control platform. This process uses the Soft AP
method to wirelessly connect the FHD Camera to the Customer’s network.
3.1 Using Soft AP to Enroll Camera
• Set up the camera as described in the previous section.
- Connect the camera’s AC power adapter and plug it into a power
outlet.
- Wait for the power LED to blink green/amber.
• Connect to the camera’s network SSID using a laptop or mobile device. The
SSID is the model number of the camera and part of the MAC address. For
example, SSID = RC845 (XX:XX:XX).
• Open a web browser (IE, Chrome, Firefox, etc.). Type in adt1.com and you
will be directed to the install wizard page.
• Choose a language.
• Click Scan for Wi-Fi Networks and select the Customer’s router SSID.
ADT RC845 FHD Indoor Camera
Quick Installation Guide
RC845 Indoor FHD Camera Installation Guide
7
Note: Control cameras will connect to the
Customer’s Wi-Fi network to access the
Internet to be added to the Control
platform. It is imperative that the customer
understands that all camera locations are
limited by their existing Wi-Fi network and
its range. Additionally, the Customer will
need to enter their SSID password during
the subsequent step.
• Enter the wireless credentials and click Save.
• The LED will turn solid green when data is being transmitted indicating that
the connection to the Customer’s router is complete.
• Connect a laptop or mobile device to the Customer’s network and log in to
the Control web portal, https://www.adt.com/control-login, to complete the
setup.
• Select Video from the menu list.
• Click Settings and select Add Video Device.
ADT RC845 FHD Indoor Camera
Quick Installation Guide
RC845 Indoor FHD Camera Installation Guide
8
• Select install from the video device list to begin adding camera. If a laptop
or mobile device are not on the Customer’s network, then enter the MAC
address of the camera.
• Follow the on-screen instructions to finish adding the camera.
ADT RC845 FHD Indoor Camera
Quick Installation Guide
RC845 Indoor FHD Camera Installation Guide
9
4 ADT Pulse Enrollment
This section provides instructions for wirelessly enrolling the RC845 Indoor
FHD Camera into the ADT Pulse network. This process uses the Wi-Fi
Protected Setup (WPS) with PIN method to wirelessly enroll the FHD Camera
to the gateway via the ADT Pulse Portal or TS Installer App.
4.1 Using WPS PIN to Enroll Camera
• Set up the camera as described in Section 2.
• Launch an Internet browser and log in to the Pulse portal or TS Installer
app.
• Enter the Manage Devices screen using one of these methods:
- For Pulse portal, select the System Tab and click Manage Devices.
- For TS Installer app, click the Pulse Devices link. The Manage
Devices screen will display.
• In the Manage Devices screen, click Cameras.
• Click the Add Using WPS button located at the bottom of the screen.
ADT RC845 FHD Indoor Camera
Quick Installation Guide
RC845 Indoor FHD Camera Installation Guide
10
• Locate the camera’s PIN number on the product label on the rear of the
camera.
• Enter the camera’s PIN into the WPS PIN field.
• Ensure that the camera is powered on and that the LED is flashing
green/amber.
ADT RC845 FHD Indoor Camera
Quick Installation Guide
RC845 Indoor FHD Camera Installation Guide
11
• Click the Continue button to initiate the WPS process. The following screen
appears.
• Press and hold the WPS/Reset button on the camera for 5 seconds to
establish a wireless connection.
• The LED flashes amber as the gateway attempts to connect to the camera.
The wireless connection is successful when the LED turns solid green
Note: You must complete the WPS connection within 2 minutes or else the
process will timeout. The time remaining is displayed in the upper-left portion
of the screen.
ADT RC845 FHD Indoor Camera
Quick Installation Guide
RC845 Indoor FHD Camera Installation Guide
12
• The following screen is shown while the camera is configured
• When the Camera Details screen appears, showing that the camera has
been enrolled, assign the RC845 a unique name (usually based on the
location of the camera) in the Name field, and then click Save.
ADT RC845 FHD Indoor Camera
Quick Installation Guide
RC845 Indoor FHD Camera Installation Guide
13
• The Pulse enrollment is complete. The newly added device is shown in the
Cameras list.
• At the top of the screen, click Go Back.
• You are returned to the Manage Devices screen. The total number of
installed cameras has increased by one.
• Click Close and Close again to confirm.
ADT RC845 FHD Indoor Camera
Quick Installation Guide
RC845 Indoor FHD Camera Installation Guide
14
• Wait until the LED is lit solid green, and then disconnect the camera from
power.
• Install the camera in its final location.
- Please refer to Section 5: Wall Mounting
ADT RC845 FHD Indoor Camera
Quick Installation Guide
RC845 Indoor FHD Camera Installation Guide
15
5 Wall Mounting
This section provides details for final mounting of the RC845 Indoor FHD
Camera. You should ensure that the camera is configured and enrolled in the
platform before permanently mounting it.
• Locate an unused, non-switchable, indoor outlet to plug the AC/DC Power
Adapter into. This outlet should be located as close as possible to the
location where the camera will be permanently mounted.
Caution: Do not plug in the power adapter until all the connections
are completed and the camera is fully mounted.
• Locate the mounting plate at the bottom of the camera stand, press the
tabs down, and slide the mounting plate forward to release it from the
stand.
• Hold the mounting plate at the location where you would like to mount the
camera and mark the location of the two mounting holes.
• Drill two pilot holes on the mounting surface at the marked location.
• If using the anchors, insert them into the mounting holes.
• Align the two mounting holes on the camera stand with the two pilot holes
and mount the mounting plate to the surface using the two supplied
screws.
• Slide the camera stand onto the mounting plate until it clicks into place.
ADT RC845 FHD Indoor Camera
Quick Installation Guide
RC845 Indoor FHD Camera Installation Guide
16
• Remove the cable organizer grommet from the stand, insert the power
cable into the hole, run the cable through the organizer slot, and insert the
organizer grommet to hold the cable in place.
• Connect the power cable into the back of the camera and plug the adapter
end into power outlet.
Caution: Use only the power adapter provided. Using a different
power adapter can result in hardware damage.
• Screw/attach the camera onto the camera stand.
• Adjust the camera to the desired position and secure it firmly.
• Verify that the camera is active on the wireless network and is recognized
by the platform.
5.1 Smart IR and Mounting Suggestion
To get the best video quality for targets at night, make sure that the camera’s
field of view does not include a large foreground object, such as tabletop,
side wall or column. If installing on a tabletop, place the camera as close to
the edge as possible. If installing on a wall, angle the camera so that a
minimal portion of the wall or column is visible, as demonstrated in the
photos in row 2 below.
ADT RC845 FHD Indoor Camera
Quick Installation Guide
RC845 Indoor FHD Camera Installation Guide
17
The RC845 uses a smart IR function for night viewing. This means that the
camera automatically adjusts the IR light output and gain. As a result, if any
objects are in the close foreground of the image, the camera lowers the IR
light output to prevent overexposing those objects. The drawback of the
smart IR function is that this feature causes background objects to receive
less IR light and to be displayed with lessened detail. This result is typical for
the smart IR function
6 Troubleshooting
This section provides details for troubleshooting wireless
connection issues of the RC845 Indoor Day/Night FHD Camera.
6.1 If the Camera Continually Goes Offline
If after it is enrolled the camera continually goes offline (LED blinks green
continually), the camera will automatically attempt to recover the wireless
connection. If the camera cannot recover on its own, take the following
measures to re-establish the Wi-Fi connection.
• Power cycle the camera.
• If the previous measure fails, power cycle the gateway.
• If the previous measure fails, move the gateway closer to the camera, if
possible.
• If the previous measure fails, press the camera’s reset button for 15
seconds, and then re-enroll the camera into the platform.
• If the previous measure fails, install a Wi-Fi Range Extender
- EX6100 for Control
- WN3000RPH-3ADPAS for Pulse
ADT RC845 FHD Indoor Camera
Quick Installation Guide
RC845 Indoor FHD Camera Installation Guide
18
7 Appendix
7.1 Technical Specifications
Sensor and Lens
Image Sensor
1/2.7” 2.1MP, WDR CMOS Senor
Minimum Illumination
0 Lux (with IR LED On)
Lens FoV (Field-of-View)
Diagonal Viewing Angle: 145°
LDC Enabled, FoV:135°(D), 124°(H), 79° (V)
Video
Video Compression
H.264 Main Profile L4.1, M-JPEG
Video Streaming
Simultaneous, H.264, M-JPEG
Image Settings
Flip, Brightness, Sharpness, Saturation, Contrast
Resolution & Frame Rate
1080p, 720p, VGA, QVGA, Up to 30 fps
Audio
Microphone
Built-in Dual Microphone Array
Two-Way Audio
Bi-directional Full Duplex Audio, Echo Cancellation,
Speaker
Built-in Speaker (1w)
Alarm and Event Management
Alarms
Motion Detection, Audio Detection
Event Notification
Push Notification, Email, Text Notification
Network
Wireless
802.11ac, 2x2, Dual Band, 2.4GHz/5GHz
Protocols
TCP/IP, UDP, ICMP, NTP, HTTP, HTTPS, RTP, RTCP
Hardware
Connectors
DC Power Jack
Processor
CPU: ARM Cortex A9, 720 MHz
Memory
Flash: 128MB, RAM: 256MB
Night Vision
IR LED x 2; Range: 16 feet (5 meters)
LED Indicator
1 tri-color LED for Power, Network/WPS
Push Button
Reset (with WPS Function)
Power Adapter
Input: 100~240 VAC, 50~60 Hz
Compliance
FCC, IC, UL, cUL
Dimensions (HxWxD)
3.98” x 1.82” x 1.72” (101mm x 46.3mm x 43.7mm
Weight
Environment
Operation
Temperature: 32° ~ 104°F (0° ~ 40°C)
Storage
Temperature: -4° ~ 158°F (-20° ~ 70°C)
Accessories
Accessories
Power Supply (12VDC/1A, 100~240VAC) Stand
Ordering Information
Part Number
RC845: Full HD Wireless IP Camera
ADT RC845 FHD Indoor Camera
Quick Installation Guide
RC845 Indoor FHD Camera Installation Guide
19
7.2 Regulatory Approvals
7.2.1 Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Country Code selection feature to be disabled for products marketed to the
US/CANADA
ADT RC845 FHD Indoor Camera
Quick Installation Guide
RC845 Indoor FHD Camera Installation Guide
20
7.2.2 Industry Canada Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-
exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference
(2) This device must accept any interference, including interference that may
cause undesired operation of the device
Cet appareil contient des émetteurs / récepteurs exempts de licence qui sont
conformes au (x) RSS (s) exemptés de licence d'Innovation, Sciences et
Développement économique Canada. L'opération est soumise aux deux
conditions suivantes:
(1) Cet appareil ne doit pas causer d'interférences
(2) Cet appareil doit accepter toute interférence, y compris les interférences
pouvant provoquer un fonctionnement indésirable de l'appareil
Caution:
the device for operation in the band 5150–5250 MHz is only for indoor use
to reduce the potential for harmful interference to co-channel mobile satellite
systems;
Avertissement:
les dispositifs fonctionnant dans la bande de 5150 à 5250MHz sont réservés
uniquement pour une utilisation à l'intérieur afin de réduire les risques de
brouillage préjudiciable aux systèmes de satellites mobiles utilisant les
mêmes canaux;
Radiation Exposure Statement:
This equipment complies with Canada radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme Canada limites d'exposition aux radiations
dans un environnement non contrôlé. Cet équipement doit être installé et
utilisé à distance minimum de 20cm entre le radiateur et votre corps.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

ADT RC845 Guide d'installation

ADT
Marque
ADT
Modèle
RC845
Catégorie
Des caméras de sécurité
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents