Modern Forms FR-W2101 Wynd XL Mode d'emploi

Wynd XL

Installation Instructions

works with the

Google Assistant

FR-W2101

Wynd XL Instructions2

Please read and

save these instructions

before installation

DO NOT RETURN TO STORE

FR-W2101Wynd XL Instructions 3

For all questions about your ceiling fan please read all included

instructions, installation procedures, troubleshooting guidelines

and warranty information before starting installation.

For missing parts or general inquiries call our trained technical staﬀ at:

1-866-810-6615 option 1

MON-FRI 8AM-8PM EST

Email: customerservice@modernforms.com

Or live chat at modernforms.com

For fast service have the following information below when you call:

1. Model Name and Number

2. Part Number and Part Description

3. Date Of Purchase and Purchase Location

1-866-810-6615 option 2

MON-FRI 8AM-8PM EST

Email: fansupport@modernforms.com

General Inquiries

Fan Support

FR-W2101

Wynd XL Instructions4

For operation, maintenance, and troubleshooting information,

visit http://modernforms.com/fan-support/

To reduce the risk of electric shock, ensure electricity has been turned oﬀ at the circuit breaker

before beginning. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA

70” and local electrical codes. Electrical installation should be performed by a licensed electrician.

The fan must be mounted with a minimum of 7 ft. (2.1m) clearance from the trailing edge of

the fan blades to the floor and a minimum of 1.5 ft (0.5m) from the edge of the fan blades to the

surrounding walls. Never place objects in the path of the fan blades. To avoid personal injury or

damage to the fan and other items, please be cautious when working around or cleaning the fan.

To avoid electrical shock or damage to the motor or ﬁnish, do not use water or chemicals

when cleaning the fan or fan blades. A dry cloth or lightly dampened cloth will be suitable

for most cleaning.

After making electrical connections, spliced conductors should be turned upward and pushed

carefully up into the outlet box. The wires should be spread apart with the grounded conductor and

the equipment-grounding conductor on one side of the outlet box, and the ungrounded conductor

on the other side of the outlet box.

All set screws must be checked and re-tightened

where necessary before installation.

Safety Rules

FR-W2101 Wynd XL Instructions 5

WARNING: Do not install or use your fan if any part(s) is/are damaged or missing. This product

is designed for use only with the supplied parts and/or accessories designated for use with this

product by Modern Forms. Substitution of parts or accessories not designated for use with this

product by Modern Forms could result in personal injury or property damage and will void the

warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing.

WARNING: To reduce the risk of electric shock, this fan must

be installed and operated with the supplied wall control, or controlled from the Modern Forms app

or Wi-Fi Touch Panel Wall Control (not included).

WARNING: Do not use power tools to assemble or install your fan. Using power tools can result in

improper assembly which can lead to noise or fan damage,personal injury or property damage.

WARNING: To reduce the risk of personal injury, do not bend the blade arms when installing the

brackets, balancing the blades or cleaning the fan.

WARNING: Do not insert foreign objects between rotating fan blades.

WARNING: Do not operate fan unless fan blades are in place. Noise and fan damage can occur

WARNING: This appliance is not intended for use by young children without supervision.

WARNING: To reduce the risk of ﬁre, electric shock, personal injury or damage to the fan or other

items, the outlet box and support structure must be securely mounted and capable of reliably

supporting a minimum of 35 Ibs (15.9 kg). Use only UL/cUL listed outlet boxes marked “FOR FAN

SUPPORT.” Use only the screws and washers provided with the outlet box.

CAUTION: Before assembling your fan, refer to the “Making the Electrical Connections“

section. If you feel you do not have enough wiring knowledge or experience, have your fan

installed by a licensed electrician.

NOTE: Before servicing or cleaning the fan, switch power oﬀ at the circuit breaker.

FR-W2101

Wynd XL Instructions6

Get Smart...

Integrates

seamlessly with:

devices you already own

works with the

Google Assistant

Premium smart

features:

Accessories:

DC

MOTOR

complement high quality materials

personalize your experience

Quiet, reliable, and up to 70%

more ecient than AC fans

Wi-Fi and Bluetooth enabled

for exible control

Bluetooth Wall Control

Dims light to 1% | ON/OFF

6 fan speeds | Sold separately

F-WCBT-WT White

Bluetooth Remote Control

Dims light to 1% | ON/OFF

6 fan speeds

F-RCBT-WT White

Wet Location-listed to the strictest

UL/cUL safety regulations. Finished

and rated for interior and exterior use

FR-W2101 Wynd XL Instructions 7

Contents

Tools Required

1. Mounting Options 10

2. Installing the Mounting Bracket 12

3. Attaching the Fan Blades / Blade Press Plates 12

4. Assembling the Fan 14

5. Hanging the Fan 16

6. Making the Electrical Connections 18

7. Installing the Optional Wall Control 20

7. Installing the Optional Wall Control 22

8. Finishing the Installation 22

9. Controlling the Fan 24

10. Reset 26

11. Breeze Mode 26

12. Application 26

13. Accessories 28

14. Troubleshooting 30-32

14. Troubleshooting cont. 32

FR-W2101

Wynd XL Instructions8

Package Contents

8. Luminaire Module

F4IN-120V-R1-30

9. Luminaire Cover

RPL-F2101-COVER-**

10. Acrylic Shade

RPL-F1801-GLA

11. Control receiver

w/Hardware (***)

F-R3-2101-072

12. Remote w/Wall Cradle

F-RCBT-WT

Hardware Bag

RPL-F2101-**-PARTS

1. Blade Set

RPL-F2101-**-BD-***

2. Blade Press Plates

3. Mounting Bracket

Downrod Assembly

RPL-HGR-ASM-XL-**

4. Canopy & Canopy Ring

RPL-CAN-CYL-XL-**

5. Coupling Cover

RPL-COU-CVR-***

6. Motor Housing

7. Adapter Plate

** denotes ﬁnish code of fan

Before discarding packaging materials be certain all parts have been removed.

Place the parts from the hardware bag into a small container to keep them from being lost.

AMachine Screws (2)

Spring Washers (2)

Flat Washers (2)

BScrews with Lock Washers (28)

C

Wood Screw (1)

Spring Washer (1)

Flat Washer (1)

DWire Nuts (11)

(Included with receiver)

FR-W2101 Wynd XL Instructions 9

IMPORTANT: Please make note of

the MAC ID on the receiver and

keep it in a safe place.

MAC ID

12

1

2

4

8

9

10

11

5

6

7

3

Hanging Weight: 35 lbs

FR-W2101

Wynd XL Instructions10

1. Mounting Options

CAUTION: To prevent electrical shock, ensure electricity has been

turned oﬀ at the circuit breaker before beginning.

If there isn’t an existing UL/cUL listed outlet box, please refer to the

following instructions. Secure the outlet box directly to the building

structure. Use appropriate fasteners and building materials. The

outlet box and support structure must be able to fully support the

moving weight of the fan (at least 35 lbs/15.9 kg). Do not use plastic

outlet boxes. Use only UL/cUL listed outlet boxes marked

“FOR FAN SUPPORT.”

Secure the outlet box directly to the building structure.

Figures 1-1C are examples of diﬀerent ways to mount the

outlet box.

NOTE: To hang your fan where there is an existing ﬁxture but no

ceiling joist, you may need an installation hanger bar.

NOTE: Downrod fans can be suspended up to a maximum

recommended length of 72” using additional downrods

(sold separately) and the included 80” lead wire.

NOTE: The sloped ceiling kit (sold separately) is required for sloped

ceiling applications, and will accommodate slopes up to 45° (Fig. 1B).

NOTE: You may need a longer downrod to maintain proper blade

clearance when installing on a steep, sloped ceiling (Fig. 1B).

FR-W2101 Wynd XL Instructions 11

1

1A

1B

1C

1

2

1

2

3

1. Support Brace

2. Outlet Box

3. Joist

1. Support Brace

2. Mounting Bracket

3. Recess Outlet Box

1. Outlet Box

Support Ceiling

Max 30° Angle

FR-W2101

Wynd XL Instructions12

2. Installing the Mounting Bracket

CAUTION: Remember to disconnect the power at the circuit breaker.

1. Remove 1 set screw from mounting bracket and set aside for use in

Finishing the Installation.

2. Pass supply wires through mounting bracket and secure to outlet

box. Verify supply wire colors and designations (Fig. 2A).

3. Secure the mounting bracket to the ceiling outlet box with the

screws and washers provided with your outlet box.

1. Insert blade in slots, aligning with motor assembly holes.

2. Put blade press plate on the end of the blade so the blade is in

between the blade arm and press plate.

3. Secure blade with blade attachment plate, screws, and

washers. Repeat process for the remaining blades. (Fig. 3)

3. Attaching the Fan Blades / Press Plates

FR-W2101 Wynd XL Instructions 13

1. Slot

2. Blade

3. Blade Press Plates

4. Screws with Lock Washers

Refer to Hardware B

2

3

2A

1. Mounting Bracket

2. Screw

Refer to Hardware A

1

3

2

4

1

2

3

1

To Switch A

A

B

(HOT)

(Neutral)

(HOT)/

Switch

(No Neutral)

(Ground)

*Bare or Green

(Ground)

*Bare or Green

To Switch

1. cUL Listed Electrical Box

2. Mounting Screws

(outlet box screws not included)

3. 120V Wires

FR-W2101

Wynd XL Instructions14

4. Assembling the Fan

CAUTION: Failure to properly install the cotter pin and/or tighten

the set screws could result in the fan loosening and possibly falling.

NOTE: Screws for Adapter plate are preinstalled on the fan motor

assembly on the small ring at the center of the blades. Remove blue

packing ring if present.

1. Remove one screw from the inner ring on the motor assembly

and loosen the other 2 (Fig. 4).

2. Seat the Adapter Plate on the center ring and twist to lock the

keyhole cutouts onto the screws previously loosened (Fig. 4A).

3. Replace the 3rd screw and tighten all 3 until snuggly secured by

hand.

NOTE: Screws for Luminaire Module plate are preinstalled on the

Adapter Plate on the middle ring. Luminaire Module itself comes

preinstalled on its mounting plate.

4. Remove one screw from the adapter plate for the luminaire

module plate and loosen the other 2.

5. Seat the Luminaire Module Plate on the adapter plate and twist

to lock the keyhole cutouts on the screws previously loosened

(Fig. 4B).

6. Replace the 3rd screw and tighten all 3 until snuggly secured.

7. Install acrylic shade without over-tightening or install metal light

cover (Fig. 4C).

NOTE: Add metal light cover if you do not need lighting function or

prefer a diﬀerent aesthetic.

NOTE: Do not connect the LED connector wires if you are using the

metal light cover.

NOTE: Do not overtighten screws or you may strip the screws or

damage the plating.

FR-W2101 Wynd XL Instructions 15

4 4A

4C4B

1. 3 screws for adapter plate

1. Luminaire

2. Metal Light Cover

OR

1

2

1

FR-W2101

Wynd XL Instructions16

5. Hanging the Fan

CAUTION: Failure to properly install the cotter pin and/or tighten

the set screws could result in the fan loosening and possibly falling.

NOTE: Make sure all screws are tightened and that wires

are not twisted.

1. Remove screw from hanger ball. Remove hanger ball and cross

pin (Fig. 5).

2. Loosen 2 screws, clevis pin and cotter pin (Fig. 5).

NOTE: Conﬁrm all connection points on the molex connector are

tight and secure. If any wires are loose, it may cause the fan to not

function. Fig. 4 thread the downrod into the motor housing until you

can reapply the clevis and cotter pins. Tighten the 2 screws.

3. Slip the coupling cover, canopy screw cover (painted side face

down), and canopy (opened side up) onto the downrod. Coupling

cover goes all the way to the bottom. Reinstall the hanger ball

onto the downrod (Fig. 5A).

4. Seat all into the mounting bracket. Rotate until ball drops and

locks into hanger bracket screw (Fig. 5B).

5. Secure the safety cable into the structure beams using the wood

screw, washers, and spring washers provided. Refer to Hardware C

NOTE: Safety cable is required for all ceiling fan installations in

Canada. Safety cable is required for ceiling fan and light (combo)

installations over 35 lbs. in both flush and downrod models in the

United States.

FR-W2101 Wynd XL Instructions 17

5

5B

5A

1. Canopy

2. Canopy Ring

3. Coupling Cover

4. Molex Connector

5. Clevis Pin

6. Cotter Pin

7. Motor Housing Screws

8. Wood Screw

9. Safety Cable

8

1

4

2

6

7

3

5

9

FR-W2101

Wynd XL Instructions18

6. Making the Electrical Connections

WARNING: Installation of this fan requires that a three-conductor

cable (including ground wire) which should run between ceiling and

wall outlet box.

WARNING: Check to see that all connections are tight, including

ground, and that no bare wire is visible at the wire nuts,

except for the ground wire.

Take note of Mac ID on page 9 before inserting the receiver into the

mounting bracket with the flat side of the receiver facing the ceiling

(Fig. 6).

1. Motor to Receiver & Receiver to house supply wires (Fig. 6A).

Refer to Hardware D

1. Connect the hanger ball/downrod assembly ground wire,

mounting bracket ground wire and receiver ground wire to

the ground wire in outlet box.

WARNING: Failure to connect ground wires could result in

poor fan control functionality.

2. Connect the red wire from the fan to the red wire marked

“TO MOTOR” from the receiver.

3. Connect the grey wire from the fan to the grey wire marked

“TO MOTOR” from the receiver.

4. Connect the yellow wire from the fan to the yellow wire marked

“TO MOTOR” from the receiver.

5. Connect the white wire from the fan to the white wire marked

“FOR LIGHT” from the receiver.

6. Connect the blue wire from the fan to the blue wire marked

“FOR LIGHT” from the receiver.

7. Connect the black (hot) wire from the ceiling to the black wire

marked “AC in L” from the receiver.

8. Connect the white (neutral) wire from the ceiling to the white

wire marked “AC in N” from the receiver.

FR-W2101 Wynd XL Instructions 19

Follow the steps above to connect the fan to your household wiring. Use the plastic wire nuts with your fan.

Secure the plastic wire nuts with electrical tape. Make sure there are no loose strands or connections.

6

6A

Black(Hot)

can be RED from Switch leg

Black(Line in H)

RED(to Motor)

GREEN(Ground)

BLUE (to Light)

BLUE (for Light)

GREEN(GND Must Use)

GREEN(Hanger Bracket Ground)

RED(to Motor)

GREY(to Motor)

WHITE(Neutral)

WHITE(to Light)

WHITE(Neutral)

Safety Cable

GREY(to Motor)

YELLOW(to Motor)

WHITE(Line in N)

YELLOW(to Motor)

Outlet

Box

Receiver

Hanger Ball & Downrod

Hanger

Bracket

1

2

1. Mounting Bracket

2. Receiver

FR-W2101

Wynd XL Instructions20

7. Installing the Optional Wall Control

1. Connect the green wire marked “GROUND” from the wall

control to the copper wire from the wall outlet box that

feeds back to the circuit breaker – important for proper

fan function (Fig. 7).

2. Connect the black wire marked “LINE IN” from the wall control to

the black LINE VOLTAGE wire from the wall outlet box that feeds

back to the circuit breaker (Fig. 7).

3. Connect the red wire from the wall control to the black wire from

the wall outlet box that feeds up to the fan (Fig. 7).

4. Connect the white wire from the wall control to the white

(neutral) wire from the wall outlet box (Fig. 7).

5. Carefully tuck the wire connections inside the outlet box.

Secure the wall control with the two (2) wall control screws

provided (Fig. 7A).

6. Attach the wall mounting plate over the wall switch and secure

with the two (2) wall mounting plate screws provided (Fig. 7A).

7. Fasten the wall plate to the wall mounting plate (Fig. 7A).

7

Wall Switch WiresHouse Wires

(Hot In)

(Neutral)

(Ground)

(Hot out to Fan)Fan Switch leg

(Copper/Ground)

(Neutral)

(Hot)

From Breaker

* Home Wiring may vary

to Fan

La page charge ...

Modern Forms FR-W2101 Wynd XL Mode d'emploi

Modern Forms FR-W2101 Wynd XL Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents