Bowflex PR3000 Assembly Manual

Taper
Assembly Manual

Ce manuel convient également à

Assembly Manual
Manuel de montage
Nautilus
®
Bowflex
®
Schwinn
®
Fitness Universal
®
PR3000 Home Gym
8001491.120112.B
Français Canadien
English
®
®
Table of Contents
Before Assembly...................................................................... 2
Tools ........................................................................................... 2
Important Safety Instructions ................................................ 3
Hardware .................................................................................. 4
Parts ........................................................................................... 5
Assembly ................................................................................... 6
Assemble the Base .......................................................... 6
Attach the Rod Pack ........................................................ 7
Attach the Lower Lat Assembly ..................................... 8
Attach the Seat Support Rail .......................................... 9
Attach Pulley Arms ......................................................... 10
Attach the Seat Bottom to the Seat Backbone ......... 11
Attach Leg Extension Assembly ................................... 12
Attach Seat Back ............................................................ 13
Attach the Lat Crossbar with Pulleys ........................................... 14
Attach the Rear Lat Cross Bar ...................................... 15
Attach the Upper Lat Tower Assembly ....................... 16
Attach the Lat Pulley Housing ...................................... 17
Cable and Pulley Routing .............................................. 18
Connect the Rod Cables ................................................ 19
Connect the Right Cable ................................................ 20
Leg Extension Cable Routing ........................................ 21
Final Inspection ............................................................... 21
Gymnase à domicile PR3000 ............................................... 22
Contacts................................................................................... 44
Before Assembly
Select where you are going to locate your Bowflex
®
home gym carefully. The best location is on a hard, level surface. For best
results, assemble your home gym in the location where you intend to use it. For safe operation, allow a workout area of at least
100” x 86” (2.6m x 2.2m) of free space.
Follow these basic tips when assembling your home gym
.
1. Collect all the pieces needed for each assembly step.
2. Turn all the bolts and locknuts toward the right to tighten
. Turn towards the left to loosen.
3. Use a combination wrench to grip the locknut when you tighten a bolt that has a locknut to make sure it is tight.
4.
You may find the use of a utility knife or scissors beneficial during the unpacking and assembly process.
5. Carefully lift pieces when attaching. Look through the bolt holes to help guide bolt placement.
6. Assembly requires 2 people.
NOTICE: Leave all of the cables wrapped and bagged until the Bowflex® home gym is completely assembled.
Tools
• (2)AdjustableWrenches(notincluded)
• Phillips Head Screwdriver (not included)
Assembly Manual
2
Important Safety Instructions
• Keepbystandersandchildrenawayfromtheproductyouareassemblingatalltimes.
• Donotassemblethismachineoutdoorsorinawetormoistlocation.
• Makesureassemblyisdoneinanappropriateworkspaceawayfromfoottrafficandexposuretobystanders.
• Somecomponentsofthemachinecanbeheavyorawkward.Useasecondperson whendoingtheassembly
stepsinvolvingtheseparts.Donotdostepsthatinvolveheavyliftingorawkwardmovementsonyourown.
• Setupthismachineonasolid,level,horizontalsurface.
• Donottrytochangethedesignorfunctionalityofthismachine.Thiscouldcompromisethesafetyandcanvoid
the warranty.
• If replacement parts are necessary use only genuine Nautilus® replacement parts and hardware. Failure to
use genuine replacement parts can cause a risk to users, keep the machine from operating correctly or void the
warranty.
• Donotuseorputthemachineintoserviceuntilthemachinehasbeenfullyassembledandinspectedforcorrect
performance in accordance with the Owner’s Manual.
• ReadandunderstandthecompleteOwnersManualsuppliedwiththismachinebeforefirstuse.Keepthe
Owner’s and Assembly Manuals for future reference.
Thisiconmeansapotentiallyhazardoussituationwhich,ifnotavoided,couldresultindeathorseriousinjury.
Read and understand all warnings on this machine.
Carefully read and understand the Assembly Manual.
Obey the following warnings:
Assembly Manual
3
Hardware
(Hardwarenotactualsize)
Qty. 13
Item #1
3/8”x 3/4” Hex Head
Bolt
Qty. 2
Item #11
1/2” x 9 1/2” Threaded
Stud
Qty. 2
Item #2
5/16”x 2 1/2” Hex Head
Bolt
Qty. 4
Item #12
Ball Stop
Qty. 5
Item #3
1/4”Washer
Qty. 2
Item #13
3/8” x 3” Hex Head Bolt
Qty. 4
Item #4
1/2”Washer
Qty. 2
Item #14
1/2” x 5 1/4” Hex Head
Bolt
Qty. 29
Item #5
3/8”Washer
Qty. 4
Item #15
5/16” x 3/4” Hex Head
Bolt
Qty. 3
Item #6
#10 x 1” Phillips Head
Screw
Qty. 4
Item #16
3/8” x 2 3/4” Hex Head
Bolt
Qty. 8
Item #7
3/8” Nylock Nut
Qty. 6
Item #17
5/16”Washer
Qty. 4
Item #8
1/2”WideWasher
Qty. 1
Item #18
Seat Pin
Qty. 6
Item #9
1/2” Nylock Nut
Qty. 2
Item #19
1/4 x 1” Phillips Head
Screw
Qty. 6
Item #10
Snap Hook
Qty. 2
Item #20
3/8” x 3 1/4” Hex Head
Bolt
Assembly Manual
4
Parts
21 1 Base Platform
22 1 Right Frame Rail
23 1 Left Frame Rail
24 1 Rear Cross Bar
25 1 Central Support
26 1 Lat Cross Bar with Pulleys
27 1 Rear Lat Cross Bar
28 1 Upper Lat Tower
29 1 Right Pulley Arm
30 1 Left Pulley Arm
31 1 Rod Pack
32 1 Lower Lat Tower
33 1 Seat Back
34 1 Seat Backbone
35 1 Seat Bottom
36 1 Seat Support Rail
37 2 Floating Pulleys
38 1 Lat Pulley Housing
39 1 Leg Extension Assembly
40 2 Roller Tubes
41 4 Foam Roller Pads
42 1 Placard
43 1 Rod Pack Strap
44 2 AdjustableHandgrips
45 2 Handgrips
46 1 Accessory Bag #1
47 2 Leg Press Extension Cables
48 1 Snap Hook
49 1 Accessory Bag #2
50 4 Roller End Caps
51 1 Leg Extension Lock Pin
52 1 Seat Backbone Lock Pin
53 1 Hardware Bag
54 1 ManualKit
55 1 Rod Box End Plate
Item # Item #
Qty.
Qty.
Description
Description
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
38
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
Assembly Manual
5
Assembly
Step 1: Assemble the Base
Parts
• BasePlatform(#21)
• RightFrameRail(#22)
• LeftFrameRail(#23)
• RearCrossBar(#24)
• CentralSupport(#25)
Hardware
• (4)3/8”x3/4”HexHeadBolts(#1)
• (4)3/8”x23/4”HexHeadBolts(#16)
• (12)3/8”Washers(#5)
• (4)3/8”NylockNuts(#7)
Tools
(2)AdjustableWrenches(notincluded)
1-1 Put the Base Assembly parts on the floor.
1-2 Align the bolt holes on the Right and Left Frame Rails with the holes in the Base Platform, Rear Cross Bar and the
Central Support.
1-3 Insert all the hardware, but do not tighten.
1-4Withallthehardwareinplace,tightenit.
22
23
24
21
5
16
25
1
7
Assembly Manual
6
Assembly
Step 2: Attach the Rod Pack
Parts
• RodPack(#31)
• LowerLatTower(#32)
• RodPackStrap(#43)
Hardware
• (3)#10x1”PhillipsHeadScrews(#6)
• (5)1/4”Washers(#3)
• (2)1/4x1”PhillipsHeadScrews(#19)
Tools
PhillipsHeadScrewDriver(notincluded)
2-1 Slide the Rod Pack into the Lower Lat Tower.
2-2 Install and tighten the hardware.
32
31
43
3
6
19
3
Assembly Manual
7
Assembly
Step 3: Attach the Lower Lat Assembly to the Base Assembly
Parts
• CompetedAssembly(fromstep1)
• LowerLatTowerAssembly(fromstep2)
Hardware
• (4)3/8”Washers(#5)
• (2)3/8”NylockNuts(#7)
• (2)3/8”x31/4”HexHeadBolts(#20)
Tools
AdjustableWrench(notincluded)
3-1 Put the Lower Lat Tower Assembly onto the Completed Assembly.
3-2 Install and tighten the hardware.
5
7
20
Assembly Manual
8
Assembly
Step 4: Attach the Seat Support Rail
Parts
• SeatSupportRail(#36)
• CompletedAssembly(fromstep3)
Hardware
• (4)3/8”x3/4”HexHeadBolts(#1)
• (4)3/8”Washers(#5)
Tools
AdjustableWrench(notincluded)
4-1 Attach the Seat Support Rail to the Lower Lat Tower.
4-2 Install and tighten the hardware.
5
1
36
Assembly Manual
9
Assembly
Step 5: Attach the Pulley Arms
Parts
• RightPulleyArm(#29)
• LeftPulleyArm(#30)
• CompletedAssembly(fromstep4)
Hardware
• (2)1/2”x91/2”ThreadedStuds(#11)
• (4)1/2”WideWashers(#8)
• (4)1/2”NylockNuts(#9)
Tools
• (2)AdjustableWrenches(notincluded)
5-1 Attach the the Right and Left Pulley Arms to the Completed Assembly.
5-2 Install and tighten the hardware.
9
8
9
11
8
29
30
Assembly Manual
10
Assembly
Step 6: Attach the Seat Bottom to the Seat Backbone
Parts
• SeatBottom(#35)
• SeatBackbone(#34)
Hardware
• (4)5/16”x3/4”HexHeadBolts(#15)
• (4)5/16”Washers(#17)
• (1)SeatPin(#18)
Tools
AdjustableWrench(notincluded)
6-1 Attach the Seat Bottom to the Seat Backbone.
6-2 Install and tighten the hardware.
6-3 Attach to Seat Support Rail.
35
34
17
15
18
Assembly Manual
11
Assembly
Step 7: Attach the Leg Extension Assembly
Parts
• LegExtensionAssembly(#39)
• RollerTubes(#40)
• (4)FoamRollerPads(#41)
• LegExtensionLockPin(#51)
• SeatBottomAssembly(fromstep6)
Hardware
• (1)SeatPin(#18)
7-1 Attach the Leg Extension Assembly to the Seat Bottom Assembly with the Leg Extension Lock Pin.
39
51
41
40
Assembly Manual
12
Assembly
Step 8: Attach the Seat Back
Parts
• SeatBack(#33)
• CompletedAssembly(fromstep5)
Hardware
• (2)5/16”x21/2”HexHeadBolts(#2)
• (2)5/16”Washers(#17)
Tools
AdjustableWrench(notincluded)
8-1 Attach the Seat Back to the Seat Support Rail.
8-2 Install and tighten the hardware.
33
17
2
Assembly Manual
13
Assembly
Step 9: Attach the Lat Crossbar with Pulleys to the Upper Lat Tower
Parts
• LatCrossbarwithPulleys(#26)
• UpperLatTower(#28)
Hardware
• (2)3/8”x3”HexHeadBolts(#13)
• (4)3/8”Washers(#5)
• (2)3/8”NylockNuts(#7)
Tools
• (2)AdjustableWrenches(notincluded)
9-1 Attach the Lat Crossbar with Pulleys to the Upper Lat Tower.
9-2 Install and tighten the hardware.
7
5
13
28
26
Assembly Manual
14
Assembly
Step 10: Attach the Rear Lat Cross Bar
Parts
• RearLatCrossBar(#27)
• UpperLatTowerAssembly(fromstep9)
Hardware
• (2)1/2”x51/4”HexHeadBolts(#14)
• (4)1/2”Washers(#4)
• (2)1/2”NylockNuts(#9)
Tools
• (2)AdjustableWrenches(notincluded)
10-1 Attach the Rear Lat Cross Bar to the Upper Lat Tower Assembly.
27
14
4
9
Assembly Manual
15
Assembly
Step 11: Attach the Upper Lat Tower Assembly
Parts
• CompletedAssembly(fromstep8)
Hardware
• (2)3/8”x3/4”HexHeadBolts(#1)
• (2)3/8”Washers(#5)
Tools
AdjustableWrench(notincluded)
11-1 Attach the Upper Lat Tower Assembly to the Base Assembly.
11-2 Install and tighten the hardware.
5
1
Assembly Manual
16
Assembly
Step 12: Attach the Lat Pulley Housing
Parts
• LatPulleyHousing(#38)
• CompletedAssembly(fromstep11)
Hardware
• (3)3/8”x3/4”HexHeadBolts(#1)
• (3)3/8”Washers(#5)
Tools
AdjustableWrench(notincluded)
12-1 Attach the Lat Pulley Housing to the Lat Tower.
Note: Rod Pack removed from illustration for clarity.
1
1
38
5
Assembly Manual
17
Assembly
Step 13: Cable and Pulley Routing the Rear Pulleys
Parts
• CompletedAssembly(fromstep12)
Tools
AdjustableWrench(notincluded)
13-1Removethe3/8”x41/2”HexHeadBoltandthe3/8”WasherinthecenteroftheLatPulleyHousing.
13-2 Remove the two pulley wheels from the Lat Pulley Housing.
13-3 Unwrap the Right Pulley Cable from the Right Frame Rail and thread it under and then over one of the pulley wheels.
Pinch the Right Pulley Cable to the pulley wheel until installed.
13-4 Unwrap the Left Pulley Cable on the Left Frame Rail and thread it under and then over the other pulley wheel.
13-5 Put the pulleys with the cables wrapped around them back into the Lat Pulley Housing.
13-6Replaceandtightenthe3/8”x41/2”HexHeadBoltandthe3/8”WasherinthecenteroftheLatPulleyHousing.
Assembly Manual
18
Assembly
Step 14: Connect the Rod Cables through the Right Floating and Lat Tower Pulleys
14-1 Put the right cable that runs through the Lat Pulley Housing through the Floating Pulley (A).
14-2 Pull the same cable through the Pulley on the Rear Lat Cross Bar (B) and then through the Pulley on the Front Lat Cross
Bar (C).
14-3PutthecableendthroughtheCableEndBallStop(D).
14-4 Attach the Cable Core (E) to keep the cable from falling out of the pulleys.
14-5 Repeat steps 14-1 through 14-4 on the opposite side.
A
C
B
D
E
Assembly Manual
19
Assembly
Step 15: Connect the Right Squat Cable through the Floating and Main Assembly Pulleys
15-1 Unwrap the Right Squat Cable from the Pulley on the front of the Base.
15-2 Put the cable under the cable shroud and under and through the Rear Cross Bar Pulley. Follow the arrows.
15-3 Put the cable down through the Inner Right Frame Rail Pulley and up through the Right Pulley Arm Pulley.
15-4 Put the cable end through the Cable End Ball Stop (A).
15-5 Attach the Cable Core (B) to keep the cable from falling out of the pulleys.
15-6 Repeat steps 15-1 through 15-5 on the opposite side.
A
B
Assembly Manual
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Bowflex PR3000 Assembly Manual

Taper
Assembly Manual
Ce manuel convient également à

dans d''autres langues