Bull NovaScale R430 F2 Guide de démarrage rapide

NovaScale R430 F2

Getting Started With Your

System

Guide de mise en route

NOVASCALE

REFERENCE

86 X1 61FD 00

NOVASCALE

NovaScale R430 F2

Getting Started With Your System

Guide de mise en route

Hardware/Matériel

November/Novembre 2009

BULL CEDOC

357 AVENUE PATTON

B.P.20845

49008 ANGERS CEDEX 01

FRANCE

REFERENCE

86 X1 61FD 00

The following copyright notice protects this book under Copyright laws which prohibit such actions as, but not limited

to, copying, distributing, modifying, and making derivative works.

2009

Trademarks and Acknowledgements

Citrix and XenServer are trademarks of Citrix Systems, Inc. and/or more of its subsidiaries, and may be registered in

the United States

Patent and Trademark Office and in other countries. Intel and Xeon are registered trademarks of Intel

Corporation in the U.S. and other countries; Microsoft, Hyper-V, Windows, and Windows Server are

either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other

countries. Red Hat and Enterprise Linux are registered trademarks of Red Hat, Inc. in the United States

and other countries; SUSE is a registered trademark of Novell, Inc., in the United States and other

countries. VMware is a registered trademark of VMware, Inc. in the United States and/or other

jurisdictions.

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Bull disclaims any proprietary interest in trademarks and

trade names other than its own.

We acknowledge the rights of the proprietors of the trademarks mentioned in this manual.

All brand names and software and hardware product names are subject to trademark and/or patent protection.

Quoting of brand and product names is for information purposes only and does not represent trademark

misuse.

The information in this document is subject to change without notice. Bull will not be liable for errors

contained herein, or for incidental or consequential damages in connection with the use of this material.

Getting Started

With Your System

book.book Page 1 Tuesday, December 1, 2009 8:36 AM

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use

of your computer.

WARN ING : A WARNING indicates a potential for property damage,

personal injury, or death.

____________________

book.book Page 2 Tuesday, December 1, 2009 8:36 AM

Getting Started With Your System 3

Installation and Configuration

WA RNIN G: Before performing the following procedure, review the safety

instructions that came with the system.

Unpacking the System

Unpack your system and identify each item.

Installing the Rails and System in a Rack

Assemble the rails and install the system in the rack following the safety

instructions and the rack installation instructions provided with your system.

book.book Page 3 Tuesday, December 1, 2009 8:36 AM

4 Getting Started With Your System

Optional – Connecting the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable to

plug into each connector. Be sure to tighten the screws (if any) on the monitor's

cable connector.

Connecting the Power Cables

Connect the system’s power cable(s) to the system and, if a monitor is used,

connect the monitor’s power cable to the monitor.

book.book Page 4 Tuesday, December 1, 2009 8:36 AM

Getting Started With Your System 5

Installing the Power Cord Retention Bracket

Attach the power cord retention bracket on the right bend of the power supply

handle. Bend the system power cable into a loop as shown in the illustration and

attach to the bracket’s cable clasp.

Plug the other end of the power cable(s) into a grounded electrical outlet

or a separate power source such as an uninterrupted power supply (UPS)

or a power distribution unit (PDU).

Turning On the System

Press the power button on the system and the monitor. The power indicators

should light.

book.book Page 5 Tuesday, December 1, 2009 8:36 AM

6 Getting Started With Your System

Installing the Optional Bezel

Install the bezel (optional).

Operating System Installation

The NovaScale R430 F2 offers an embedded Configuration utility: the Unified

Server Configurator - Lifecycle Controller Enabled (USC-LCE), which includes

an OS Deployment Wizard that assists you with the installation of the Operating

System.

Refer to the technical characteristics of the server on

http://www.bull.com/novascale

to get the list of supported operating systems.

NOTE: The list of operating systems offered by the USC may be larger than the

list of the supported Operating Systems.

NOTE: for the installation of a supported Operating System not listed in the USC,

see

http://support.bull.com

.

Residing on an embedded flash memory card, USC-LCE is similar to a BIOS

utility in that it can be started during the boot sequence and can function

independently of an installed operating system.

USC-LCE provides drivers that may be required for operating system

installation, depending on which operating system you are installing. The OS

Deployment wizard extracts these drivers and copies them to a staging directory.

These files are deleted after an 18-hour period or when you press the <F10> key

to either cancel operating system installation or re-enter USC after rebooting.

book.book Page 6 Tuesday, December 1, 2009 8:36 AM

Getting Started With Your System 7

NOTE: During the 18-hour period when the drivers are extracted to the temporary

location, you cannot update USC, drivers, or diagnostics using a Driver Update

Package after the operating system is installed, or the Driver Update Package will

display a message that another session is open.

For supported Microsoft® Windows® operating systems, these extracted

drivers are installed during the operating system installation. For supported

Linux operating systems, you must manually install the extracted drivers after

the operating system installation is complete.

Before installing the operating system, the OS Deployment wizard detects if a

boot device is available. A boot device is a physical disk, virtual disk, or other

storage device on which the operating system can be installed.

To begin installation

1

Connect the keyboard, monitor, mouse, and any additional peripherals to

your system.

2

Turn on the system and the attached peripherals.

3

Press

<F10>

in the POST to start the System Services.

NOTE: The Initializing UEFI. Please wait... and the Entering System Services...Starting

Unified Server Configurator messages are displayed.

4

Click

OS Deployment

in the left pane.

5

Click

Deploy OS

in the right pane.

NOTE: If your system has a RAID controller, you have the option of launching the RAID

Configuration wizard and configuring a virtual disk as the boot device.

NOTE: If your system does not have a RAID controller, the OS Deployment wizard

bypasses the RAID configuration option and goes directly to "Select an Operating System".

If your system does not have a RAID controller or if you choose to bypass the optional RAID

configuration, the OS Deployment wizard installs the operating system to a default location,

which is typically the disk identified as Disk 0 in the BIOS utility.

6

Select the operating system you want to install, and click

book.book Page 7 Tuesday, December 1, 2009 8:36 AM

8 Getting Started With Your System

7

USC or USC - LCE extracts the drivers required by the operating system you

selected. The drivers are extracted to an internal USB drive named

OEMDRV.

NOTE: For Red Hat® Enterprise Linux® 4.x server and Red Hat Enterprise Linux 5.x

server, the drivers are extracted to OEMDRV under /oemdrv/*.rpm.

For SUSE® Linux Enterprise Server 10 SP2, the drivers are extracted under

/linux/suse/x86_64-sles10/install/*.rpm.

NOTE: The process for extracting the drivers may take several minutes.

NOTE: All drivers copied by the OS Deployment wizard are removed after 18 hours. You

must complete the operating system installation within 18 hours for the copied drivers to be

available. To remove the drivers before the 18-hour period is over, reboot the system and

press the <F10> key to re-enter USC.

8

After the drivers are extracted, USC or USC - LCE prompts you to insert the

operating system installation media.

NOTE: When installing the Microsoft Windows operating system, the extracted drivers are

automatically installed during the operating system installation. When installing the Linux

operating system, the operating system installation uses native drivers. After the Linux

installation is complete, you need to manually install the drivers extracted by USC. See

"Update Drivers for Linux Systems Only".

9

Insert the operating system installation media when prompted and click

NOTE: USC-LCE supports internal SATA optical drives, USB optical drives, and virtual

media devices. If the installation media is corrupt or not readable, then USC may be unable to

detect the presence of a supported optical drive. In this case, you may receive an error

message stating that no optical drive is available. If the media is not valid (if it is the incorrect

CD or DVD, for example), a message displays requesting that you insert the correct

installation media.

book.book Page 8 Tuesday, December 1, 2009 8:36 AM

Getting Started With Your System 9

10

Click Finish to reboot the system and continue with the operating system

installation. Upon reboot, the system boots to the operating system

installation media.

NOTE: When the system reboots after you click Finish, you may be prompted to press a

key before booting to the operating system installation media. If you do not press a key, the

system boots to the hard drive and not the operating system installation media.

NOTE: : In the event that the operating system installation is interrupted and the system

reboots before installation completes, you may be prompted to press a key in order to boot

from the operating system installation media.

NOTE: You can cancel the operating system installation by pressing the <F10> key.

Pressing the <F10> key at any point during the installation process or while rebooting causes

any drivers provided by the OS Deployment wizard to be removed.

NOTE: Microsoft Windows Server 2008 UEFI operating system installations are not

currently supported.

CAUTION: During Red Hat 5.x installation, you will receive a warning that a read-only

file system was detected; Linux has detected the temporary storage area of USC that stores

updates for your system. Click OK, and a second warning will appear indicating that the

read-only file system has a loop partition layout and that it needs to be formatted. Click the

Ignore drive button. You may see both warnings several times during the course of Red Hat

5.x installation.

CAUTION: During the beginning of Windows Server® 2003 installation, the installer

will automatically detect and possibly assign the default drive letter C to the USC temporary

storage device OEMDRV. Creating a new Windows-bootable system partition on the hard

drive will assign the partition to a drive letter other than C; this is standard Windows

installer behaviour. To assign the new partition to C, see "Assign a Windows-Bootable

System Partition to the C: Drive".

Update Drivers for Linux Systems Only

On the following operating systems, it is advised to update your system with the

extracted drivers after installation. The drivers are extracted to a drive (or

device) named OEMDRV.

• Red Hat Enterprise Linux 4.7 server - The location of the drivers on the

OEMDRV drive after installation is:

/oemdrv/*.rpm

• Red Hat Enterprise Linux 5.2 server - The location of the drivers on the

OEMDRV drive after installation is:

/oemdrv/*.rpm

• SUSE Linux Enterprise Server 10 with Service Pack 2 - The location of the

drivers on the OEMDRV drive after installation is:

/linux/suse/x86_64-

sles10/install/*.rpm

Use the following command to install the drivers: rpm -Uvh *.rpm.

book.book Page 9 Tuesday, December 1, 2009 8:36 AM

10 Getting Started With Your System

NOTE: If the command rpm –Uvh *.rpm fails to install a driver because a newly

version of the DKMS package is needed, see the

http://support.bull.com

website to

download the latest version of the DKMS package, then:

• install this DKMS package by launching the command:

rpm –Uvh dkms <version-release>.noarch.rpm

• install the Linux drivers by launching the command:

find ./* -not –name dkms* -exec rpm –Uvh {} \;

Kickstart Installation for the Linux Operating System

If you are using a kickstart installation for the Linux operating system, provide

the following information in the post-installation script:

• Command to mount the USB device containing the operating system drivers

labeled OEMDRV.

For example:

mkdir OEMDRV

mount /dev/sdc1 /mnt/OEMDRV

• Path to the operating system drivers on the OEMDRV drive:

For Red Hat Enterprise Linux:

/oemdrv/*.rpm

For SUSE Linux Enterprise Server:

/linux/suse/x86_64-sles10/install/*.rpm

• Command to install the drivers:

rpm -Uvh *.rpm

Assign a Windows-Bootable System Partition to the C: Drive

After you have completed the USC or USC - LCE portion of Windows Server

2003 installation, your server will reboot and begin the text-mode portion of the

installation. During this phase, you may need to perform the following steps to

ensure Windows installs to your C: drive.

NOTE: Following these instructions after Windows Server 2003 setup presents

you with a list of existing drive partitions and/or unpartitioned space available on

your computer.

1

Select the unpartitioned space, and then press <c> to create a hard-disk

partition. Follow the on-screen instructions to create a partition.

NOTE: The partition may not be enumerated as a C: drive.

2

Select the newly-created partition, and then press <d> to delete the partition.

Follow the on-screen instructions to delete the partition.

book.book Page 10 Tuesday, December 1, 2009 8:36 AM

Getting Started With Your System 11

3

Select the unpartitioned space again, and then press <c> to create a primary

hard-disk partition.

NOTE: The partition will now be enumerated as C: drive.

4

Follow the on-screen instructions to create a partition. Windows will now

install on the C: drive.

For more information on assigning the Windows-bootable system partition to

the C: drive, see

http://support.microsoft.com/kb/896536

.

Other Information You May Need

WA RNIN G: See the safety and regulatory information that shipped with your

system. Warranty information may be included within this document or as

a separate document.

• The rack documentation included with your rack solution describes how to

install your system into a rack.

•The

Hardware Owner’s Manual

provides information about system features

and describes how to troubleshoot the system and install or replace system

components. This document is available online at

http://support.bull.com/documentation.

• Any media that ships with your system that provides documentation and

tools for configuring and managing your system, system management

software, system updates, and system components that you purchased with

your system.

NOTE: Always check for updates on

http://support.bull.com

and read the

updates first because they often supersede information in other documents.

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system does not

perform as expected, see

http://support.bull.com/documentation

for further

documentation, or contact your support representative; the phone directory is at

http://support.bull.com

.

book.book Page 11 Tuesday, December 1, 2009 8:36 AM

12 Getting Started With Your System

Technical Specifications

Processor

Processor type Intel

®

Xeon

®

processor 5500 series

Expansion Bus

Bus type PCI Express Generation 2

Expansion slots One full-height, half-length x16 link

Memory

Architecture 1066 or 1333 MHz DDR3 registered or

unbuffered Error Correcting Code (ECC)

DIMMs.

Memory module sockets Eight 240-pin

Memory module capacities 1 GB, 2 GB, 4 GB, or 8 GB

Minimum RAM 1 GB (one processor) or 2 GB (two processors)

Maximum RAM 32 GB (one processor) or

64 GB (two processors)

Drives

Hard drives Up to four 3.5-inch, cabled or hot-swap SAS or

SATA internal drives

or

Up to four 2.5-inch, hot-swap SAS, SATA,

or SSD internal drives

Diskette drive Optional external USB 1.44-MB

Optical drive One optional internal slimline SATA

DVD-ROM or DVD+/-RW drive

NOTE: DVD devices are data only.

Optional external USB DVD-ROM

Connectors

Back

book.book Page 12 Tuesday, December 1, 2009 8:36 AM

Getting Started With Your System 13

NIC

Two RJ-45 (for integrated 1-GB NICs)

Serial

9-pin, DTE, 16550-compatible

USB

Two 4-pin, USB 2.0-compliant

Video

15-pin VGA

Front

Video

15-pin VGA

USB

Two 4-pin, USB 2.0-compliant

Internal

USB

Two 4-pin, USB 2.0-compliant

Video

Video type Matrox G200, integrated in Winbond

WPCM450

Video memory 8 MB

Power

AC power supply

(per power supply)

Wattage

480W (non-redundant power supply)

500W (redundant power supply)

Vo l t a g e

100-240 VAC, 50/60 Hz, 7.5-3.8 A

(non-redundant power supply)

100-240 VAC, 50/60 Hz, 7-3.5 A

(redundant power supply)

Heat dissipation

1637 BTU/hr maximum

(non-redundant power supply)

1706 BTU/hr maximum

(redundant power supply)

Maximum inrush current

Under typical line conditions and over

the entire system ambient operating range, the

inrush current may reach 25 A per power

supply for 10 ms or less.

Connectors (continued)

book.book Page 13 Tuesday, December 1, 2009 8:36 AM

14 Getting Started With Your System

Batteries

System battery

CR 2032 3.0-V lithium ion coin cell

Physical

Height 4.3 cm (1.69 in)

Width 43.4 cm (17.09 in)

Depth 62.7 cm (24.69 in)

Weight (maximum configuration) 15.9 kg (35.02 lb)

Environmental

Temperature

Operating

10° to 35°C (50° to 95°F) with a maximum

temperature gradation of 10°C per hour

NOTE: For altitudes above 2950 feet, the

maximum operating temperature is derated

1ºF/550 ft.

Storage

–40° to 65°C (–40° to 149°F) with a maximum

temperature gradation of 20°C per hour

Relative humidity

Operating

20% to 80% (noncondensing) with a maximum

humidity gradation of 10% per hour

Storage

5% to 95% (noncondensing)

Maximum vibration

Operating

0.26 Grms at 5–500 Hz for 15 min

Storage

1.54 Grms at 10–250 Hz for 15 min

Maximum shock

Operating

One shock pulse in the positive z axis

(one pulse on each side of the system) of 31 G

for 2.6 ms in the operational orientation

Power (continued)

book.book Page 14 Tuesday, December 1, 2009 8:36 AM

Getting Started With Your System 15

Storage

Six consecutively executed shock pulses in the

positive and negative x, y, and z axes

(one pulse on each side of the system) of 71 G

for up to 2 ms

Altitude

Operating

–16 to 3048 m (–50 to 10,000 ft)

NOTE: For altitudes above 2950 feet, the

maximum operating temperature is derated

1ºF/550 ft.

Storage

–16 to 10,600 m (–50 to 35,000 ft)

Airborne Contaminant Level

Class

G2 or lower as defined by ISA-S71.04-1985

Environmental (continued)

book.book Page 15 Tuesday, December 1, 2009 8:36 AM

16 Getting Started With Your System

book.book Page 16 Tuesday, December 1, 2009 8:36 AM

La page est en cours de chargement...

Bull NovaScale R430 F2 Guide de démarrage rapide

Bull NovaScale R430 F2 Guide de démarrage rapide

dans d''autres langues

Documents connexes

Autres documents