N-Tron 1000 Manuel utilisateur

Marque: N-Tron

Modèle: 1000

Taper: Manuel utilisateur

Ce manuel convient également à

N-Tron 1000 Series

N-Tron

Series 1000

Unmanaged Gigabit Industrial

Mid-Span POE Injectors

Hardware Guide | August 2016

20 Willow Springs Circle

York, PA 17406

Inc. All other company and product names are trademarks of their respective owners.

The information contained in this document is subject to change without notice. Red Lion makes no warranty

of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability

or fitness for a particular purpose. In no event shall Red Lion be liable for any incidental, special, indirect or

consequential damages whatsoever included but not limited to lost profits arising out of errors or omissions

in this manual or the information contained herein.

CONTACT INFORMATION:

AMERICAS

Inside US: +1 (877) 432-9908

Outside US: +1 (717) 767-6511

Hours: 8am-6pm Eastern Standard Time

(UTC/GMT -5 hours)

ASIA-PACIFIC

Shanghai, P.R. China: +86 21-6113-3688 x767

Hours: 9am-6pm China Standard Time

(UTC/GMT +8 hours)

EUROPE

Netherlands: +31 (0) 33 4 4723-225

France: +33 (0) 1 84 88 75 25

Germany: +49 (0) 89 5795 9421

UK: 44 (0) 20 3868 0909

Hours: 9am-5pm Central European Time

(UTC/GMT +1 hour)

Website: www.redlion.net

Email: [email protected]

N-Tron® Series Unmanaged Gigabit Industrial Mid-Span PoE+ Injector Hardware Guide i

Table of Contents Revised 2016-08-30

Drawing No. LP0986

Table of Contents

Preface

Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Compliance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Part 15 of the Federal Communications Commission (FCC) - A Rules: Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Industry Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Environmental Impact Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Toxic Emissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Trademark Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Release Notes and Document Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Publication History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Document Comments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Additional Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

General Safety Cautions and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Electrical Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Environmental Safety Cautions and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

Introduction and Specifications

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1000-POE+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Key Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Key Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Regulatory Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Product Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

1000-POE4+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Key Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Key Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Regulatory Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

Product Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

Installation

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Revised 2016-08-30 Table of Contents

Drawing No. LP0986

ii N-Tron® Series Unmanaged Gigabit Industrial Mid-Span PoE+ Injector Hardware Guide

Installing/Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

DIN-Rail Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Power Connection (Top View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Grounding Techniques for 1000 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

RJ45 Connector Crimp Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13

Typical Application. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13

Connecting the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

Operation and Maintenance

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16

Verify/Troubleshoot Cable Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16

Red Lion Controls N-Tron 1000 Series Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17

N-Tron® Series Unmanaged Gigabit Industrial Mid-Span PoE+ Injector Hardware Guide iii

Preface Revised 2016-8-30

Drawing No. LP0986

Preface

Disclaimer

Portions of this document are intended solely as an outline of methodologies to be followed during the

maintenance and operation of N-Tron® Series Unmanaged Gigabit Industrial Mid-Span PoE+ Injectors. It is not

intended as a step-by-step guide or a complete set of all procedures necessary and sufficient to complete all

operations.

While every effort has been made to ensure that this document is complete and accurate at the time of release, the

information that it contains is subject to change. Red Lion Controls is not responsible for any additions to or



alterations of the original document. Industrial networks vary widely in their configurations, topologies, and traffic

conditions. This document is intended as a general guide only. It has not been tested for all possible applications,

and it may not be complete or accurate for some situations.

Users of this document are urged to heed warnings and cautions summarized at the front of the document, such as

electrical hazard warnings.

Compliance Information

It is recommended that the owner of this equipment determine and ensure conformance with any specific and

applicable local regulations.

Part 15 of the Federal Communications Commission (FCC) - A Rules: Interference

Every effort has been made to ensure that this equipment is designed to comply with the limits for a Class A digital

device, as described in the FCC Rules.

This product complies with Part 15 of the FCC-A Rules.

Operation is subject to the following conditions:

1. This device may not cause harmful Interference

2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

Operation of this device in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at their own expense.

Industry Canada

This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment

Regulations. Operation is subject to the following two conditions; (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

Cet appareillage numérique de la classe A répond à toutes les exigences de l'interférence canadienne causant des

règlements d'équipement. L'opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas

causer l'interférence nocive, et (2) ce dispositif doit accepter n'importe quelle interférence reçue, y compris



l'interférence qui peut causer l'opération peu désirée.

iv N-Tron® Series Unmanaged Gigabit Industrial Mid-Span PoE+ Injector Hardware Guide

Revised 2016-8-30 Preface

Drawing No. LP0986

Environmental Impact Statement

Red Lion equipment contains no hazardous materials as defined by the United States Environmental Protection

Agency (USEPA). Red Lion recommends that all failed product be returned to Red Lion for failure analysis and

proper disposal.

Toxic Emissions

Red Lion equipment releases no toxic emissions.

Trademark Acknowledgments

Ethernet is a registered trademark of Xerox Corporation. All other company and product names are trademarks of

their respective owners.

Release Notes and Document Updates

The hard copy and electronic media versions of this document are revised only at major releases and therefore,

may not always contain the latest product information. As needed, Documentation Notes and or Product Bulletins

will be provided between major releases to describe any new information or document changes.

The latest online version of this document and all product updates can be accessed through the Red Lion web site

http://www.redlion.net/documentation.

Publication History

The following information lists the release history of this document.

Related Documents

Visit the Technical Resources page on the Red Lion website at the following link to view available documents

related to this product.

http://www.redlion.net/documentation

Document Comments

Red Lion appreciates all comments that will help us to improve our documentation quality. The user can submit

comments through the Red Lion Customer Service. Simply email us at customer[email protected].

Additional Product Information

Additional product information can be obtained by contacting the local sales representative or Red Lion through the

contact numbers and/or e-mail addresses listed in the inside of the front cover of this manual.

Warnings and Cautions

Warnings apply to situations where personal injury or death may result.

Cautions apply to where reduced function or damage to equipment may result.

ISSUE/REVISION RELEASE DATE CONTENT DESCRIPTION

2016-08-30 August 2016 Initial Release

N-Tron® Series Unmanaged Gigabit Industrial Mid-Span PoE+ Injector Hardware Guide v

Preface Revised 2016-8-30

Drawing No. LP0986

General Safety Cautions and Warnings

CAUTION: If the N-Tron series equipment is used in the manner not specified by Red Lion, the

protection provided by the equipment may be impaired.

ATTENTION: Si l' N-Tron série équipement est utilisé d'une manière non spécifiée par Red Lion,

la protection fournie par l'équipement peut être compromise.

CAUTION: Do not perform any services on the unit unless qualified to do so. Do not substitute

unauthorized parts or make unauthorized modifications to the unit.

ATTENTION: Ne pas effectuer de services sur l'appareil s'il n'est pas qualifié pour le faire. Ne pas

substituer pièces non autorisées ou de modifications non autorisées de l'appareil.

CAUTION: Do not operate the equipment in a manner not specified by this manual.

ATTENTION: Ne pas faire fonctionner l'équipement d'une manière non spécifiée par ce manuel.

WARNING: Install only in accordance with Local and National Codes of authorities having

jurisdiction.

ALERTE: Installer uniquement, conformément aux codes locaux et nationaux des autorités ayant

compétence.

Electrical Safety Warnings

WARNING: Do not work on equipment or cables during periods of lightning activity.

ALERTE: N

e pas travailler sur le matériel ou les câbles pendant les périodes d'activité de la

foudre.

WARNING: Properly ground the unit before connecting anything else to the unit. Units not

properly grounded may result in a safety risk and coul

d be hazardous and may void the warranty.

See the grounding technique section of this Hardware Guide for proper ways to ground the unit.

ALERTE: C

orrectement à la terre de l'unité avant tout raccordement à l'unité. Unités pas

correctement mise à la terre peut entraîner un risque de

sécurité et pourraient être dangereux et

peut annuler la garantie. Voir la section technique de mise à la terre de ce mode d'emploi des

moyens appropriés à la masse de l'appareil.

WARNING: This equipment must be used with a Listed UL Class 2 Power Supply.

ALERTE: Cet équipement doit être utilisé avec une

alimentation UL Listed Classe 2.

WARNING: A Recognized or Listed fuse, rated maximum 3A, minimum 30VDC, must be installed

on the line side of the device. Applies to 1000-POE4+ only.

ALERTE: Un fusible reconnu ou classé, classé 3A maximale, 30VDC minimum, doit être installé

sur le côté de la ligne de l'appareil. S’appliue aux seuls 1000POE4+.

WARNING: 1000POE4+: Use 110°C or higher rated copper wire, (0.22Nm) 2 lb/in tightening

torque for field installed conductors.

1000POE+: Use 60/75°C or higher rated copper wire, (0.22Nm) 2 lb/in tightening torque for field

installed conductors.

ALERTE: 1000POE4+: Utilisez 110°C ou nominale supérieure fil de cuivre, (0,22 Nm) 2 lb/pouce

couple de serrage pour le champ installé conducteurs.

1000POE+: Utilisez 65/75°C ou nominale supérieure fil

de cuivre, (0,22 Nm) 2 lb/pouce couple de

serrage pour le champ installé conducteurs.

WARNING: Do not operate the unit with the end plates removed, as this could create a shock or

fire hazard.

ALERTE : Ne pas faire fonctionner l'unité avec les plaques d'extrémité retiré, ce qui pourrait créer

une décharge électrique ou un incendie.

CAUTION: Observe proper DC Voltage polarity when installing power input cables. Reversing

voltage polarity can cause permanent damage to the unit and voids the warranty.

ATTENTION:

Respecter la polarité correcte de tension DC lors de l'installation des câbles

d'alimentation d'entrée. Inversion de polarité de ten

sion peut causer des dommages permanents à

l'appareil et annule la garantie.

vi N-Tron® Series Unmanaged Gigabit Industrial Mid-Span PoE+ Injector Hardware Guide

Revised 2016-8-30 Preface

Drawing No. LP0986

Environmental Safety Cautions and Warnings

CAUTION: This equipment is suitable for use in Class I, Division 2, Groups A, B, C, and D or

non-hazardous locations only.

ATTENTION: Cet équipement est adapté pour une utilisation dans la classe I, Division 2, Groupes

A, B, C et D ou non dangereux endroits seulement.

WARNING: Explosion Hazard – Substitution of components may impair suitability for Class I,

Division 2.

ALERTE

- Risque d'explosion - Remplacement d'un composant peut empêcher la conformité de

Classe I, Division 2.

WARNING: Do not operate the equipment in the presence of flammable gases or fumes.

Operating electrical equipment in such an environment constitutes a definite safety hazard.

ALERTE : Ne pas utiliser le matériel en présence de gaz ou de vapeurs inflammables. L'utilisation

de matériel électrique dans un tel environnement constitue un danger certain.

WARNING – Explosion Hazard – Do not connect or disconnect any connections while circuit is

live unless area is known to be non-hazardous.

ALERTE - Risque d'explosion - Ne pas brancher ou débrancher les connexions lorsque le circuit

est sous tension sauf si la zone est connue pour être non dangereux.

WARNING: Disconnect the power and allow to cool 5 minutes before touching.

ALERTE: D

éconnectez le câble d'alimentation et laisser refroidir 5 minutes avant de la toucher.

WARNING: These products are open-type devices and are meant to be installed in an enclosure

suitable for the environment this is only accessible with the use of a tool in accordance with the

National Electrical Code (NEC), NFPA 70.

ALERTE : Ces produits sont des appareils de type ouvert et sont destinés à être installés dans un

boîtier adapté à l'environnement ce n'est accessible qu'avec l'utilisation d'un outil en conformité

avec le National Electrical Code (NEC), NFPA 70

N-Tron® Series Unmanaged Gigabit Industrial Mid-Span PoE+ Injector Hardware Guide vii

Preface Revised 2016-8-30

Drawing No. LP0986

viii N-Tron® Series Unmanaged Gigabit Industrial Mid-Span PoE+ Injector Hardware Guide

Revised 2016-8-30 Preface

Drawing No. LP0986

N-Tron® Series Unmanaged Gigabit Industrial Mid-Span PoE+ Injector Hardware Guide 1-1

Introduction and Specifications Revised 2016-08-30

Drawing No. LP0986

Section 1 Introduction and Specifications

Introduction

Red Lion’s 1000 POE+ injector series simplifies network device deployment by combining Gigabit data

communications and power over a single Ethernet network cable. Ideal for deployment in industrial networks

including oil and gas, water/wastewater, utility, transportation, mining, and factory floor applications, the 1000-

POE+ and 1000-POE4+ injectors provide auto-sensing plug-and-play performance to PoE+ devices like video

cameras and wireless access ports.

1000-POE+

The Industrial 2-Port Gigabit PoE+ midspan injector is designed to provide Power over Ethernet for PoE capable

devices where running a power line is either not possible or not cost effective. This feature allows an end user to

power a PoE camera, wireless access point, or any other PoE capable device without the need for running

separate wires for power. This also allows the ability for a centralized battery backup for all connected devices.

Key Features

• Compact Space Saving Package

• Full IEEE 802.3 af/at Compliance

• One 10/100/1000BaseTX RJ-45 Port (Data In)

• One 10/100/1000BaseTX RJ-45 Port (Data In & Power Out)

• Unmanaged Plug and Play Operation

• Extended Environmental Specifications:

-40°C to 80°C Operating Temperature

Operational Humidity: 10% to 95% (Non Condensing)

• Supports up to 30 Watts per port (25.5 Watts at the Powered Device (PD))

• Up to 1.0 Gb/s Maximum Throughput

• Redundant Power Inputs (10-30 VDC)

• Power Fault Status LEDs

• LED PoE Status Indication

• Hardened Metal DIN-Rail Mounted Enclosure

Revised 2016-08-30 Introduction and Specifications

Drawing No. LP0986 1000-POE+ Key Specifications

1-2 N-Tron® Series Unmanaged Gigabit Industrial Mid-Span PoE+ Injector Hardware Guide

1000-POE+ Key Specifications

Table 1. 1000-POE+ Key Specifications

PHYSICAL ELECTRICAL

Height 4.30 in. (10.92 cm) Input Voltage 10-30 VDC

Width 1.00 in. (2.54 cm) Steady Input Current 1.32 A @ 24 VDC (UNDER FULL LOAD)

Depth 3.63 in. (9.22 cm)

Steady Input Current 66 mA @ 24 VDC (UNDER NO LOAD)

Weight 0.6 lbs (0.27 kg) Inrush 22.0 A/2.1 ms @ 24VDC

DIN Rail 35 mm BTU/HR

POWER OVER ETHERNET

PoE Standard

IEEE 802.3af/at Gigabit Mid-Span PSE

PoE Output Power

54 VDC/30W (25.5W at PD)

Power Pin assignment

Pins 4/5 (+) Pins 7/8 (-)

PSE Type

Type 2

ENVIRONMENTAL NETWORK MEDIA

Operating

Temperature

-40°C to 80°C 10BaseT  Cat-3 Cable

Storage

Temperature

-40°C to 85°C 100BaseT  Cat-5 Cab

Operating Humidity 10% to 95%

(Non Condensing)

1000BaseT  Cat-5e Ca

ble

Operating Altitude 0 to 10,000 ft. 802.3af (802.3at Type1) PoE  Cat-3 Cable

802.3at Type 2 PoE+

 Cat-5 Cable

CONNECTOR RECOMMENDED MINIMUM WIRING CLEARANCE

10/100/1000BaseT Two (2) RJ45 TX Copper

Port

Top 1 in. (2.54 cm)

One 10/100/1000Base-T RJ-45 Port (Data In) Front 2 in.(5.08 cm)

One 10/100/1000Base-T RJ-45 PoE Port

(Dat

a & Power Out)

N-Tron® Series Unmanaged Gigabit Industrial Mid-Span PoE+ Injector Hardware Guide 1-3

Introduction and Specifications Revised 2016-08-30

Dimensions Drawing No. LP0986

Dimensions

Revised 2016-08-30 Introduction and Specifications

Drawing No. LP0986 Product Ordering Guide

1-4 N-Tron® Series Unmanaged Gigabit Industrial Mid-Span PoE+ Injector Hardware Guide

Product Ordering Guide

PART NO. DESCRIPTION

1000-POE+ Unmanaged Industrial Single-Port Gigabit Mid-Span PoE Injector

URMK Universal Rack Mount Kit

1000-PM Panel Mount Assembly, 1000-POE+

NTPS-24-3 DIN-Rail Power Supply 24VDC @ 3 Amp

Regulatory Approvals

Safety

For use in Class I, Division 2, Groups A, B, C and D Hazardous Locations.

• UL 508, Industrial Control Equipment.

• ANSI/ISA-12.12.01-2007 for use in Class I and II, Division 2 and Class III Divisions 1 and 2 Hazardous

(Classified) Locations Groups A, B, C, D. T4A.

• cUL C22.2 No. 14-M05

• cUL C22.2 No. 213-M1987 for use in Class I, Division 2 Hazardous Locations.

EMI

•

EN61000-6-4, EN55011 - Class A

• FCC Title 47, Part 15, Subpart B - Class A

• ICES-003 – Class A

EMC

•

EN61000-6-2

• EN61000-4-2 (ESD)

• EN61000-4-3 (RS)

• EN61000-4-4 (EFT)

• EN61000-4-5 (Surge)

• EN61000-4-6 (Conducted Disturbances)

Warranty

3 years from the date of purchase.

N-Tron® Series Unmanaged Gigabit Industrial Mid-Span PoE+ Injector Hardware Guide 1-5

Introduction and Specifications Revised 2016-08-30

Drawing No. LP0986

1000-POE4+

The Industrial 4-Port Gigabit PoE+ midspan injector is designed to provide Power over Ethernet for multiple PoE

capable devices where running a power line is either not possible or not cost effective. This feature allows an end

user to power a PoE camera, wireless access point, or any other PoE capable device without the need for running

separate wires for power. This also allows the ability for a centralized battery backup for all connected devices.

Key Features

• Compact Space Saving Package

• Full IEEE 802.3 af/at Compliance

• Four 10/100/1000Base-T RJ-45 Ports (DATA IN)

• Four 10/100/1000Base-T RJ-45 PoE Ports (DATA & POWER OUT)

• Unmanaged Plug and Play Operation

• Extended Environmental Specifications:

-40°C to 85°C Operating Temperature

-Operational Humidity: 10% to 95% (Non Condensing)

• Full Wire Speed Connections

• LED PoE Status Indication

• Power Fault Status LEDs

• Up to 8 Gb/s Maximum Throughput

• Redundant Power Inputs (22-49 VDC)

• Supports up to 30 Watts per port (25.5 Watts at the Powered Device (PD))

• Hardened Metal Din Rail Enclosure

Revised 2016-08-30 Introduction and Specifications

Drawing No. LP0986 1000-POE4+ Key Specifications

1-6 N-Tron® Series Unmanaged Gigabit Industrial Mid-Span PoE+ Injector Hardware Guide

1000-POE4+ Key Specifications

Table 2. 1000-POE4+ Key Specifications

PHYSICAL ELECTRICAL

Height 5.9 in. (14.99 cm) Input Voltage 22-49 VDC

Width 2.01 in. (5.11 cm) Steady Input Current 5.25 A @ 24 VDC (UNDER FULL LOAD)

Depth 5.68 in. (14.43 cm) Steady Input Current 280 mA @ 24 VDC (UNDER NO LOAD)

Weight 1.45 lbs (0.66 kg) Inrush 59.9 Amp/60us @ 24VDC

DIN Rail 35 mm BTU/HR

POWER OVER ETHERNET

PoE Standard

IEEE 802.3af/at Gigabit Mid-Span PSE

PoE Output Power

57VDC/30W (25.5W at PD) per port

Power Pin assignment

Pins 1/2 (+) Pins 3/6 (-)

PSE Type

Type 2

ENVIRONMENTAL NETWORK MEDIA

Operating

Temperature

-40°C to 85°C 10BaseT  Cat-3 Cab

Storage

Temperature

-40°C to 85°C 100BaseT  Cat-5 Cab

Operating Humidity 10% to 95%

(Non Condensing)

1000BaseT  Cat-5e Ca

ble

Operating Altitude 0 to 10,000 ft. 802.3af (802.3at Type1) PoE  Cat-3 Cable

802.3at Type 2 PoE+

 Cat-5 Cable

CONNECTOR RECOMMENDED MINIMUM WIRING CLEARANCE

10/100/1000BaseT Eight (8) RJ45 TX Cop-

per Ports

Top 1 in. (2.54 cm)

Four 10/100/1000Base-T RJ-45 Ports (Data In) Front 2 in. (5.08 cm)

Four 10/100/1000Base-T RJ-45 PoE Ports

ata & Power Out)

N-Tron® Series Unmanaged Gigabit Industrial Mid-Span PoE+ Injector Hardware Guide 1-7

Introduction and Specifications Revised 2016-08-30

Dimensions Drawing No. LP0986

Dimensions

Revised 2016-08-30 Introduction and Specifications

Drawing No. LP0986 Product Ordering Guide

1-8 N-Tron® Series Unmanaged Gigabit Industrial Mid-Span PoE+ Injector Hardware Guide

Product Ordering Guide

PART NO. DESCRIPTION

1000-POE4+ Unmanaged Industrial 4-Port Gigabit Mid-Span PoE Injector

URMK

Universal Rack Mount Kit

1K26-PMK Panel Mount Assembly, 1000-POE4+

NTPS-24-10 DIN-Rail Power Supply 24VDC @ 10 Amp

Regulatory Approvals

Safety

•

ANSI/ISA 12.12.01-2015 Class I and II, Div. 2 and Class III, Div. 1 and 2, Groups A, B, C and D Hazardous

Locations, T4

• UL508 Industrial Control Equipment

• CAN/CSA-C22.2 No. 213-15, Hazardous Locations

• CAN/CSA-C22.2 No. 14-13, Industrial Control Equipment

EMI

•

FCC Title 47, Part 15, Radio Frequency Devices, Subpart B,

• ANSI C63.4-2009; Industry Canada ICES-003, EN 55032, EN 61000-3-2, EN61000-3-3

EMC

•

EN 55024, EN 61000-6-2, EN 61000-4-2 (ESD); EN 61000-4-3 (RFAM); EN 61000-4-4 (EFT); EN 61000-4-5

(SURGE); EN 61000-4-6 (RFCM); EN 61000-4-8 (PFMF); EN 61000-4-11 (VDI)

Warranty

3 years from the date of purchase.

N-Tron® Series Unmanaged Gigabit Industrial Mid-Span PoE+ Injector Hardware Guide 2-9

Installation Revised 2016-05-25

Introduction Drawing No. LP0986

Section 2 Installation

Introduction

This section contains the information and procedures necessary to unpack, inspect, install and connect the

N-Tron® Series Unmanaged Gigabit Industrial Mid-Span PoE+ Injector equipment.

Unpacking

Remove all the equipment from the packaging, and store the packaging in a safe place.

Inspection

Please ensure the shipping package contains the following items in undamaged condition:

1. N-Tron® Series Unmanaged Gigabit Industrial Mid-Span PoE+ Injector.

2. Instruction Sheet.

If the package contents are damaged:

1. Contact your carrier.

2. File any damage claims with the carrier.

Installing/Mounting

Read the following warning before beginning the installation:

Lire l'avertissement suivant avant de commencer l'installation:

WARNING: Never install or work on electrical equipment or cabling during periods of

lightning activity. Never connect or disconnect power when hazardous gases are

present.

ALERTE: Ne jamais installer ou de travailler sur un équipement électrique ou de

câblage pendant les périodes d'activité de la foudre. Ne jamais brancher ou débrancher

l'alimentation en gaz dangereux sont présents

Revised 2016-05-25 Installation

Drawing No. LP0986 Installing/Mounting

2-10 N-Tron® Series Unmanaged Gigabit Industrial Mid-Span PoE+ Injector Hardware Guide

DIN-Rail Mounting

a. Install the unit in a standard DIN-Rail. Recess the unit to allow at least 2” of horizontal clearance for

CAT5e cable bend radius or 5” of horizontal clearance for Fiber Optic cable bend radius.

URMK 1000-PM 1K26-PMK

Most Red Lion N-Tron Series products are designed to be mounted on industry standard 35mm DIN-Rail. How-

ever, DIN-Rail mounting may not be suitable for all applications. Our Universal Rack Mount Kit (P/N: URMK) can

be used to mount the POE+ injectors enclosures to standard 19" racks, and our Panel Mount Assembly (P/N:

1000-PM) can be used to mount the 1000 Series enclosures to a panel or any other flat surface.The 1000-POE4+

will require the 1K26-PMK panel mount.

b. To install the unit to 35mm industrial DIN-Rail,

place the top edge of the included mounting bracket

on the back of the unit against the DIN-Rail at a 15°

angle as shown. Rotate the bottom of the unit to the

back (away from you) until it snaps into place.

c. To remove the unit from the 35mm industrial

DIN-Rail, pull forward on the unit until it

disengages from the bottom of the DIN-Rail.

Rotate the bottom of the unit towards you and up

at an approximate 15° upward angle to

completely remove the unit.

La page charge ...

N-Tron 1000 Manuel utilisateur

Marque: N-Tron

Modèle: 1000

Taper: Manuel utilisateur

Ce manuel convient également à

N-Tron 1000 Series

Télécharger le PDF

rapport

dans d''autres langues

English: N-Tron 1000 User manual

N-Tron 1000 Manuel utilisateur

Ce manuel convient également à

N-Tron 1000 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents