Sharp LC-24DV510E Le manuel du propriétaire

LCD COLOUR TELEVISION OPERATION MANUAL

ENGLISH

SHARP ELECTRONICS (Europe) GmbH

Sonninstraße 3, D-20097 Hamburg

SHARP CORPORATION

http://www.sharp-eu.com

DEUTSCHFRANÇAIS

LCD-FARB-TV BEDIENUNGSANLEITUNG

TÉLÉVISEUR LCD COULEUR MODE D'EMPLOI

50186851

LC-24DV510E

English - 1 -

Contents

Features ................................................................. 3

Dear SHARP customer ........................................... 3

Introduction ............................................................. 3

Preparation ............................................................. 3

Important safety precautions .................................. 4

Safety Precautions ................................................. 5

Connection to a Television Distribution System

(Cable TV etc.) from Tuner ................................. 6

Package Contents .................................................. 7

Environmental Information ..................................... 7

Repair Information .............................................. 7

Remote Control Buttons ......................................... 8

LCD TV and Operating Buttons .............................. 9

Viewing the Connections - Back Connectors ......... 9

Viewing the Connections - Side Connectors ........ 10

Power Connection ................................................ 10

Aerial Connection ............................................. 10

Using USB Inputs ..................................................11

Connecting to a DVD Player via HDMI ................. 12

Connecting to a DVD Player via Component

Sockets (YPbPr) or Scart Cable ........................... 12

Connecting the LCD TV to a PC ........................... 13

Using Side AV Connectors ................................... 13

Remote Control Handset ...................................... 13

Inserting Batteries ............................................. 13

Switching On/Off ................................................... 13

To Switch the TV On ......................................... 13

To Switch the TV to Standby ............................. 13

To Switch the TV Off ......................................... 13

Input Selection ...................................................... 14

Basic Operations .................................................. 14

Operation with the Buttons on the TV ............... 14

Volume Setting .............................................. 14

Programme Selection ................................... 14

AV Mode ....................................................... 14

Operation with the Remote Control .................. 14

Volume Setting .............................................. 14

Programme Selection (Previous or Next

Programme) .................................................. 14

Programme Selection (Direct Access) .......... 14

Viewing Electronic Programme Guide (EPG) ....... 14

Recording via EPG Screen ............................... 15

Programme Options.......................................... 15

First Time Installation............................................ 16

Installation ............................................................ 17

Auto Channel Scan (Retune) Menu Operation . 17

Manual Tuning ..................................................... 17

Digital Aerial Manual Search............................. 17

Digital Cable Manual Search ............................ 18

Analogue Manual Search ................................. 18

Analogue Fine Tune.......................................... 18

Network Channel Scan ..................................... 18

Clear Service List (*) ......................................... 18

Managing Stations: Channel List .......................... 19

Operating the Channel List ............................... 19

Moving a Channel ............................................. 19

Deleting a Channel ........................................... 19

Renaming a Channel ........................................ 19

Locking a Channel ............................................ 19

Managing Stations: Favourites ............................. 20

Button Functions ............................................... 20

Managing Stations: Sorting Channel List ............. 20

On-Screen Information ......................................... 20

Media Playback Using Media Browser ................. 20

Viewing Videos via USB .................................. 21

Viewing Photos via USB ................................... 21

Slideshow Options ............................................ 21

Playing Music via USB ..................................... 22

Recordings Library............................................ 22

Media Browser Settings .................................... 22

Timeshift Recording ............................................. 23

Instant Recording ................................................. 23

Watching Recorded Programmes ....................... 23

Changing Image Size: Picture Formats ................ 24

Conﬁ guring Picture Settings ................................. 25

Operating Picture Settings Menu Items ............ 25

Picture Settings Menu Items ............................. 25

PC Picture Settings........................................... 26

Conﬁ guring Sound Settings .................................. 26

Operating Sound Settings Menu Items ............. 26

Sound Settings Menu Items.............................. 26

Conﬁ guring Your TV’s Settings ............................. 27

Operating Settings Menu Items ........................ 27

Settings Menu Items ......................................... 27

Using a Conditional Access Module ..................... 27

Viewing Conditional Access Menu (*) ............... 27

Conﬁ guring Language Preferences ...................... 28

Language Settings ............................................ 28

Parental Control.................................................... 28

Parental Settings Menu Operation ................... 29

Timers ................................................................... 29

Setting Sleep Timer .......................................... 29

Setting Programme Timers ............................... 29

Adding a Timer .............................................. 29

Editing a Timer .............................................. 29

Deleting a Timer ............................................ 29

Recording Conﬁ guration ....................................... 30

Conﬁ guring Date/Time Settings ............................ 30

Conﬁ guring Source Settings ................................. 31

Conﬁ guring Other Settings ................................... 31

Operation .......................................................... 31

Other Features ..................................................... 32

Teletext ................................................................. 32

Tips ....................................................................... 33

Appendix A: PC Input Typical Display Modes ....... 34

Appendix B: AV and HDMI Signal Compatibility

(Input Signal Types) .............................................. 34

Appendix C: Supported DVI Resolutions.............. 35

Appendix D: Supported File Formats for USB

Mode..................................................................... 35

Appendix E: Software Upgrade ............................ 36

Speciﬁ cations ....................................................... 37

Digital Reception (DVB-C) .................................... 37

Dimensional Drawings .......................................... 38

End of life disposal ............................................... 39

Detachable Stand Uninstallation Method ............. 40

Screw Dimensions ................................................ 41

A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 1A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 1 17.08.2011 18:23:1617.08.2011 18:23:16

English - 2 -

SPECIAL NOTE FOR USERS IN THE U.K.

The mains lead of this product is ﬁ tted with a non-rewireable (moulded) plug incorporating a 5A fuse. Should

the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked

ASA

or and of the same rating

as above, which is also indicated on the pin face of the plug, must be used.

Always reﬁ t the fuse cover after replacing the fuse. Never use the plug without the fuse cover ﬁ tted.

In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the

mains plug and ﬁ t an appropriate type.

DANGER:

The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed

of in a safe manner.

Under no circumstances should the cut-off plug be inserted elsewhere into a 5A socket outlet, as a serious

electric shock may occur.

To ﬁ t an appropriate plug to the mains lead, follow the instructions below:

IMPORTANT:

The wires in the mains lead are coloured in accordance with the following code:

Blue: Neutral

Brown: Live

As the colours of the wires in the mains lead of this product may not correspond with the coloured

markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured •

black.

The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured •

red.

Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three pin plug.

Before replacing the plug cover make sure that:

If the new ﬁ tted plug contains a fuse, its value is the same as that removed from the cut-off plug.•

The cord grip is clamped over the sheath of the mains lead, and not simply over the lead wires.•

IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 2A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 2 17.08.2011 18:23:1817.08.2011 18:23:18

English - 3 -

Features

Remote controlled colour LCD TV.•

Fully integrated Terrestrial digital-cable TV (DVB-•

T-C- MPEG2) (DVB-T-C MPEG4).

HDMI connectors for digital video and audio. This •

connection is also designed to accept high deﬁ nition

signals.

USB input.•

Programme recording•

Programme timeshifting•

1000 programmes (analogue+digital).•

OSD menu system.•

Integrated tuner DVB-T-C HD, MPEG 2 / MPEG 4 •

compatible.

Scart socket for external devices (such as video, •

video games, audio set, etc.).

Stereo sound system. (German+Nicam)•

Teletext, fastext, TOP text.•

Headphone connection.•

Automatic programming system.•

Forward or backward manual tuning.•

Sleep timer / Child lock.•

Automatic sound mute when no transmission.•

NTSC playback. •

AVL (Automatic Volume Limiting).•

Auto power down.•

PLL (Frequency Search).•

PC input. •

Plug&Play for Windows 98, ME, 2000, XP, Vista, •

Windos 7.

Game Mode •

The illustrations and the OSD in this operation •

manual are for explanation purposes and may vary

slightly from the actual operations.

The examples used throughout this manual are •

based on the LC-24DV510E model.

Dear SHARP customer

Thank you for your purchase of the SHARP LCD

colour TV product. To ensure safety and many years

of trouble-free operation of your product, please read

Important safety precautions carefully before using

this product.

Introduction

Please read the corresponding instructions of this

handbook prior to the ﬁ rst usage of the device, even

when the usage of electronic devices is familiar

to you. Notice especially the chapter SAFETY

PRECAUTIONS. Carefully keep the handbook as

future reference. When selling the device or giving it

away, absolutely give these direction for use.

Thank you for choosing this product. This manual will

guide you for the proper operation of your TV.

Before operating the TV, please read this

manual thoroughly. Please do keep this

manual in a safe place for future references.

This device is intended to receive and display TV

programs. The different connection options make

an additional expansion of the reception and display

sources possible (receiver, DVD player, DVD recorder,

VCR, PC etc.). This device is only suitable for the

operation in dry interiors. This appliance is intended

solely for private domestic use and may not be used

for industrial and commercial purposes. We exclude

liability in principle, if the device is not used as

intended, or unauthorized modiﬁ cations have been

made. To operate your LCD TV in extreme ambient

conditions may cause the damage of the device.

Preparation

For ventilation, leave a free space of at least 10 cm

all around the set. To prevent any fault and unsafe

situations, please do not place any objects on top of

the set. Use this device in moderate climates.

10 cm

A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 3A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 3 17.08.2011 18:23:1817.08.2011 18:23:18

English - 4 -

Important safety precautions

Cleaning—Unplug the AC cord from the AC outlet before cleaning the product. Use a damp cloth to clean •

the product. Do not use liquid cleaners or aerosol cleaners.

Use a soft damp cloth to gently wipe the panel when it is dirty. To protect the panel, do not use a chemical •

cloth to clean it. Chemicals may cause damage or cracks in the cabinet of the TV.

Water and moisture—Do not use the product near water, such as bathtub, washbasin, kitchen sink, laundry •

tub, swimming pool and in a wet basement.

Do not place vases or any other water-ﬁ lled containers on this product. The water may spill onto the product •

causing ﬁ re or electric shock.

Stand—Do not place the product on an unstable cart, stand, tripod or table. Doing so can •

cause the product to fall, resulting in serious personal injuries as well as damage to the product.

Use only a cart, stand, tripod, bracket or table recommended by the manufacturer or sold

with the product. When mounting the product on a wall, be sure to follow the manufacturer’s

instructions. Use only the mounting hardware recommended by the manufacturer.

When relocating the product placed on a cart, it must be moved with utmost care. Sudden •

stops, excessive force and uneven ﬂ oor surface can cause the product to fall from the cart.

Ventilation—The vents and other openings in the cabinet are designed for ventilation. Do not •

cover or block these vents and openings since insufﬁ cient ventilation can cause overheating

and/or shorten the life of the product. Do not place the product on a bed, sofa, rug or other

similar surface, since they can block ventilation openings. This product is not designed for

built-in installation; do not place the product in an enclosed place such as a bookcase or rack,

unless proper ventilation is provided or the manufacturer’s instructions are followed.

The LCD panel used in this product is made of glass. Therefore, it can break when the •

product is dropped or impact applied. If the LCD panel is broken, be careful not to be injured

by broken glass.

Heat sources—Keep the product away from heat sources such as radiators, heaters, stoves •

and other heat-generating products (including ampliﬁ ers).

To prevent ﬁ re, never place any type of candle or naked ﬂ ames on the top or near the TV •

set.

To prevent ﬁ re or shock hazard, do not place the AC cord under the TV set or other heavy items.•

Headphones—Do not set the volume at a high level. Hearing experts advise against extended listening at •

high volume levels.

Do not display a still picture for a long time, as this could cause an afterimage to remain.•

There is power consumption always if main plug is connected.•

Servicing—Do not attempt to service the product yourself. Removing covers can expose you to high voltage •

and other dangerous conditions. Request a qualiﬁ ed person to perform servicing.

The LCD panel is a very high technology product, giving you ﬁ ne picture details.

Due to the very large number of pixels, occasionally a few non-active pixels may appear on the screen as a

ﬁ xed point of blue, green or red. This is within product speciﬁ cations and does not constitute a fault.

Precautions when transporting the TV

When transporting the TV, never carry it by holding onto the speakers. Be sure to always carry the TV by two

people holding it with two hands—one hand on each side of the TV.

WARNING

To prevent the spread of ﬁ re, keep candles or other open ﬂ ames away from this product

at all times.

A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 4A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 4 17.08.2011 18:23:1817.08.2011 18:23:18

English - 5 -

Safety Precautions

Read the following recommended safety

precautions carefully for your safety.

Power Source

The TV set should be operated only from a 220-240V

AC, 50Hz outlet. Ensure that you select the correct

voltage setting for your convenience.

Power Cord

Do not place the set, a piece of furniture, etc. on the

power cord (mains lead) or pinch the cord. Handle the

power cord by the plug. Do not unplug the appliance

by pulling from the power cord and never touch the

power cord with wet hands as this could cause a short

circuit or electric shock. Never make a knot in the cord

or tie it with other cords. The power cords should be

placed in such a way that they are not likely to be

stepped on. A damaged power cord can cause ﬁ re or

give you an electric shock. When it is damaged and

needs to be replaced, it should be done by qualiﬁ ed

personnel.

Moisture and Water

Do not use this device in a humid and

damp place (avoid the bathroom, the

sink in the kitchen, and near the washing

machine). Do not expose this device to

rain or water, as this may be dangerous

and do not place objects filled with

liquids, such as ﬂ ower vases, on top.

Avoid from dripping or splashing.

If any solid object or liquid falls into the cabinet, unplug

the TV and have it checked by qualiﬁ ed personnel

before operating it any further.

Cleaning

Before cleaning, unplug the TV set

from the wall outlet. Do not use liquid

or aerosol cleaners. Use soft and dry

cloth.

Ventilation

The slots and openings on the TV set are intended for

ventilation and to ensure reliable operation. To prevent

overheating, these openings must not be blocked or

covered in anyway.

Heat and Flames

The set should not be placed near to

open ﬂ ames and sources of intense heat

such as an electric heater. Ensure that

no open ﬂ ame sources, such as lighted

candles, are placed on top of the TV. Batteries should

not be exposed to excessive heat such as sunshine,

ﬁ re or the like.

Lightning

In case of storm and lightning or when

going on holiday, disconnect the power

cord from the wall outlet.

Replacement Parts

When replacement parts are required, make sure that

the service technician has used replacement parts,

which are speciﬁ ed by the manufacturer or have the

same speciﬁ cations as the original one. Unauthorized

substitutions may result in ﬁ re, electrical shock or

other hazards.

Servicing

Please refer all servicing to qualiﬁ ed

personnel. Do not remove the cover

yourself as this may result in an electric

shock.

Waste Disposal

Packaging and packaging aids are recyclable •

and should principally be recycled. Packaging

materials, such as a foil bag should be kept away

from children

Batteries, including those which are heavy metal •

free, should not be disposed of with household

waste. Please dispose of used batteries in an

environmentally friendly manner. Find out about the

legal regulations which apply in your area.

Do not try to recharge batteries, there is a danger •

of explosion. Replace batteries only with the same

or equivalent type.

This symbol on the product or on its packaging means

that your electrical and electronic device

should be disposed at the end of its

service life separately from your

household wastes. There are separate

collection systems for recycling in the EU.

For more information, please contact the

local authority or the dealer where you

purchased the product.

Disconnecting the Device

The mains plug is used to disconnect the TV set

from the mains and therefore it must remain readily

operable.

Headphone Volume

Excessive sound pressure from earphones

and headphones can cause hearing loss.

Installation

To prevent injury, this device must be securely

attached to the wall in accordance with the installation

instructions when mounted to the wall (if the option

is available).

A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 5A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 5 17.08.2011 18:23:1917.08.2011 18:23:19

English - 6 -

LCD Screen

The LCD panel is a very high technology product with

about a million thin ﬁ lm transistors, giving you ﬁ ne

picture details. Occasionally, a few non-active pixels

may appear on the screen as a ﬁ xed blue, green or

red point. Please note that this does not affect the

performance of your product.

Warning! Do not leave your TV in standby or operating

mode when you leave your house.

Connection to a Television Distribution

System (Cable TV etc.) from Tuner

Device connected to the protective earthing of the

building installation through the mains connection or

through other apparatus with a connection to protective

earthing-and to a television distribution system using

coaxial cable, may in some circumstances create a

ﬁ re hazard.

Connection to a cable distribution system has

therefore to be provided through a device providing

electrical isolation below a certain frequency range

(galvanic isolator, see EN 60728-11).

Note:The HDMI connection between PC and TV

may cause radio interference in which case it is

recommended to use VGA(DSUB-15) connection.

The Standby Off/On button doesn´t separate this

device completely from mains. Moreover the device

consumes power in the standby operation. In order to

separate the device completely from mains, the mains

plug has to be pulled from the mains socket. Because

of that the device should be set up in a way, that an

unobstructed access to mains socket is guaranteed,

so that in case of emergency the mains plug can be

pulled immediately. To exclude the danger of ﬁ re, the

power cord should principally be separated from the

mains socket prior to a longer period of non-usage,

i.e. during vacations.

“HDMI, the HDMI logo and High-Definition •

Multimedia Interface are trademarks or registered

trademarks of HDMI Licensing LLC.”

Manufactured under license from Dolby •

Laboratories.

The “HD TV 1080p” Logo is a trademark of EICTA.•

The DVB logo is the registered trademark of the •

Digital Video Broadcasting—DVB—project.

Electrical device not in the hands of children

Never let children use any electrical device

unsupervised. Children cannot always recognise

possible dangers. Batteries / accumulators can be

life threatening when swallowed. Store batteries out

of the reach of small children. In case of swallowing

a battery medical aid has to be sought immediately.

Also keep the packaging foils away from children as

there is danger of suffocation.

Licence Notiﬁcation

DivX®, DivX Certiﬁed® and associated logos are

trade-marks of DivX®, Inc. and are used under

license.

ABOUT DIVX VIDEO: DivX® is a digital video

format created by DivX®, Inc. This is an ofﬁcial

DivX Certiﬁed® device that plays DivX® video. Visit

divx.com for more information and software tools to

convert your ﬁles into DivX video.

ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certiﬁed®

device must be registered in order to play purchased

DivX® Video-on-Demand (VOD) movies. To obtain your

registration code, locate the DivX® VOD sec-tion in

your device setup menu. Go to vod.divx.com for more

information on how to complete your registration.

A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 6A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 6 17.08.2011 18:23:1917.08.2011 18:23:19

English - 7 -

Package Contents

SLEEP

SCREEN

PRESETS

LANG.

FAV

EPG

SWAP

SOURCE

C

DISP.

SEARCH

MODE

INFO

CH

V

Remote Control

LCD TV

Batteries: 2 X AAA

Instruction Book

Quick Guide

1 X Video & Audio

Connection Cable

1 X Component Video

Connection Cable

Note: You should check the accessories after

purchasing. Make sure that each accessory is

included.

As the manufacturer’s specification supports

communication on cable lengths shall be smaller

than 3m.

Environmental Information

This television is designed to consume less energy •

to save environment.

You not only help to save the environment but also

you can save money by reducing electricity bills

thanks to the energy efﬁ ciency feauture of this TV.

To reduce energy consumption, you should take the

following steps:

You can use Power Save Mode setting, located in •

the Other Settings menu. If you set Power Save Mode

as On, the TV will switch to energy-saving mode

and luminance level of TV set will be decreased to

optimum level. Note that some picture settings will

be unavailable to be changed when the TV is in

Power Save Mode.

When the TV is not used, please switch off at •

the rear rocker switch to further reduce power

consumption.

Disconnect the TV from the mains socket when it •

will not be used for prolonged periods.

When the TV is left in stand-by it consumes a small •

amount of power switching off at the rear rocker

switch or disconnect the TV from the mains will make

further energy savings. Note activating the “Power

Save Mode” saves on an annual bases more energy

than switching off the mains when the TV is not used,

to save most energy it is highly recommended that

“Power Save Mode” is switch on.

Repair Information

Please refer all servicing to qualiﬁ ed personnel. Only

qualiﬁ ed personnel must repair the TV. Please contact

your local dealer, where you have purchased this TV

for further information.

A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 7A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 7 17.08.2011 18:23:1917.08.2011 18:23:19

English - 8 -

Remote Control Buttons

Standby1.

Image size / Zooms videos (in Media Browser 2.

video mode)

Sleep Timer3.

Mono / Stereo - Dual I-II / Currrent Language (*) 4.

(in DVB channels)

Favourite Mode Selection (in DVB channels)5.

Numeric buttons6.

Electronic programme guide (in DVB channels)7.

No function8.

Media Browser9.

Navigation buttons (Up/Down/Left/Right)10.

No function11.

Recordings Library12.

Programme Down / Page up - Programme Up / 13.

Page down

Mute14.

Programme recording15.

Pause (in Media Browser mode) / Timeshift 16.

recording

Rapid reverse (in Media Browser mode)17.

Play (in Media Browser mode)18.

Red button19.

Green button / List Schedule (in EPG) / Tag 20.

/ Untag All (in favourite list) / Play-Slideshow

(in Media Browser) / Loop-Shufﬂ e (in Media

Browser)

Picture mode selection / Changes picture mode 21.

(in Media Browser video mode)

No function22.

Teletext / Mix (in TXT mode)23.

Subtitle on-off (in DVB channels)24.

Previous programme25.

AV / Source selection26.

Menu on-off27.

Okay (Conﬁ rm) / Hold (in TXT mode) / Edit 28.

Channel List

Exit / Return / Index page (in TXT mode)29.

No function30.

Info / Reveal (in TXT mode)31.

Volume Up / Down32.

No function33.

No function34.

Rapid advance (in Media Browser mode)35.

SLEEP

SCREEN

PRESETS

LANG.

FAV

EPG

SWAP

SOURCE

C

DISP.

SEARCH

MODE

INFO

CH

V

Stop (in Media Browser mode)36.

Blue button / Edit Channel List / Filter (In 37.

Favourite List&EPG)

Yellow button / Timeline Schedule (in EPG)38.

A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 8A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 8 17.08.2011 18:23:2117.08.2011 18:23:21

English - 9 -

LCD TV and Operating Buttons

FRONT and REAR VIEW Control buttons VIEW Control Buttons

P\V-A

V

1. Standby Off/On button

2. TV/AV button

3. Programme Up/Down buttons-

Volume Up/Down buttons

Note:You can use +/- buttons

to change volume. If you want

to change channels, press P/V/

AV button once and then use

+/- buttons. If you hold the P/V/

AV button about a few seconds,

source OSD will be displayed.

Main menu OSD cannot be

displayed via control buttons.

Viewing the Connections - Back Connectors

SPDIF

SCART

VGA

Coax.OUT

1

HDMI 1: HDMI Input1.

HDMI Inputs are for connecting a device that has an HDMI socket. Your LCD TV is capable of

displaying High Deﬁ nition pictures from devices such as a High Deﬁ nition Satellite Receiver or DVD

Player. These devices must be connected via the HDMI sockets or Component Socket. These sockets

can accept either 720p or 1080i signals. No sound connection is needed for an HDMI to HDMI

connection.

RF Input2. connects to an aerial antenna system or a cable.

Note that if you use a decoder or a media recorder, you should connect the aerial cable through the device

to the television with an appropriate antenna cable, as shown in the illustration in the following pages.

SCART 3. input or output for external devices. Connect the SCART cable between SCART socket on TV and

SCART socket on your external device (such as a decoder, a VCR or a DVD player).

Note: If an external device is connected via the SCART socket, the TV will automatically switch to AV mode.

Note: S-VHS signal is supported via the scart socket.

PC Input4. is for connecting a personal computer to the TV set.

Connect the PC cable between the PC INPUT on the TV and the PC output on your PC.

SPDIF Coaxial Out5. outputs digital audio signals of the currently watched source.

Use an SPDIF coaxial cable to trasfer audio signals to a device that has SPDIF input

A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 9A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 9 17.08.2011 18:23:2117.08.2011 18:23:21

English - 10 -

Viewing the Connections - Side Connectors

CI Slot is used for inserting a CI card. A CI card allows you to view all the channels that 1.

you subscribe to. For more information, see “Conditional Access” section.

USB Inputs. 2.

Note that programme recording feature is available via these USB inputs. You can

connect external hard disk drives to this input.

TV control buttons.3.

Component Video Input (YPbPr)4. is used for connecting component video.

You can connect the component video and audio sockets with a device that has

component output. To do this, you must use the supplied component video connection

cable for enabling connection. First, plug single jack of the cable to the TV’s YPbPr socket

(side). Afterwards, insert your component cable’s (not supplied) connectors into the plural

part of the Component video connection cable. Colours of the connected jacks should

match.

Side audio-video connection5. input is used for connecting video and audio signals of

external devices. To make a video connection, you must use the supplied AV connection

cable for enabling connection. First, plug singular jack of the cable to the TV’s Side AV

socket. Afterwards, insert your video cable’s (not supplied) connector into the YELLOW

input (located on the plural side) of the supplied AV connection cable. Colours of the

connected jacks should match.

To enable audio connection, you must use RED and WHITE inputs of the side AV connection cable.

Afterwards, insert your device’s audio cable’s connectors into the RED and WHITE jack of the

supplied side AV connection cable. Colours of the connected jacks should

match.

Note: You should use audio inputs of side AV connection cable (RED &

WHITE) to enable sound connection when connecting a device to your TV

by using PC or COMPONENT VIDEO input.

Headphone jack is used for connecting an external headphone to the 6.

system. Connect to the HEADPHONE jack to listen to the TV from

headphones (optional).

7. , switch is used for turning the TV on or off.

Power Connection

IMPORTANT: The TV set is designed to operate on 220-240V AC, 50Hz.

After unpacking, allow the TV set to reach the ambient room temperature before you connect the set to the •

mains. Plug the power cable to the mains socket outlet.

Aerial Connection

Connect the aerial ,cable TV plug to the AERIAL INPUT socket located at the rear of the TV.•

SPDIF

SCART

VGA

Coax.OUT

1

Aerial or Cable

USB

5Vdc

Max:500mA

P\V-AV

SIDE AV YPbPr

A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 10A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 10 17.08.2011 18:23:2817.08.2011 18:23:28

English - 11 -

Using USB Inputs

USB Connection

You can connect a USB hard disk drive or USB •

memory stick to your TV by using the USB inputs

of the TV. This feature allows you to play ﬁ les stored

in a USB drive or record programmes.

2.5” and 3.5” inch (hdd with external power supply) •

external hard disk drives are supported.

To record a programme, you should ﬁ rst connect •

a USB disk to your TV while the TV is switched

off. You should then switch on the TV to enable

recording feature. Otherwise, recording feature will

not be available.

IMPORTANT !

You may back up your ﬁ les before making any •

connections to the TV set in order to avoid any

possible data loss. Note that manufacturer will not

be responsible for any ﬁ le damage or dataloss.

It is possible that certain types of USB devices (e.g. •

MP3 Players) or USB hard disk drives/memory sticks

may not be compatible with this TV.

IMPORTANT: The TV supports only FAT32 disk

formatting. NTFS format is not supported. If you

connect a USB disk with NTFS format, the TV will ask

you to format the content. See the section, “Format

Disk” in the following pages for more information on

disk formatting.

Note that ALL the data stored on the USB disk will

be lost and then the disk format will be converted to

FAT32 in such a case.

USB Disk Connection

• Plug your USB device to the USB input of the TV.

Note: Plug or unplug your USB disk while the TV is

switched off.

Note: If you are going to connect a USB hard disk drive

to the TV set, USB connection cable used between

the disk drive and the TV should have a USB logo

and should be as short as possible.

Note: While formatting a USB hard disk that has 1TB

(Tera Byte) or more ﬁ le capacity, you can experience

problems with the formatting process. In such a

case, you should format the disk with your personal

computer and the formatted disk type should be

FAT32.

SIDE VIEW USB MEMORY

5Vdc

Max:500mA

USB

CAUTION !

Quickly plugging and unplugging USB devices, •

is a very hazardous operation. Especially, do not

repeatedly quickly plug and unplug the drive. This

may cause physical damage to the USB player and

especially the USB device itself.

Do not pull out USB module while playing or •

recording a ﬁ le.

Programme Recording

To record a programme, you should ﬁ rst connect a

USB disk to your TV while the TV is switched off.

You should then switch on the TV to enable recording

feature.

IMPORTANT: When using a new USB hard disk drive,

it is recommended that you ﬁ rst format the disk using

your TV’s “Format Disk” option.

To use the recording function a USB 2.0 certiﬁ ed •

device of at least 1GB should be used, If the

connected USB device is not USB 2.0 an error

message will be displayed.

Recorded programmes are saved into the connected •

USB disk in .TS format (MPEG-2 transport stream).

If desirable, you can back up / copy these saved

recordings into a personal computer.

Note: It is possible that recorded broadcasts in

.TS format may not be supported by your media

playback software. In such a case, you should install

an appropriate media playback software to your

computer.

An hour of the recordings stored occupies •

approximately 2 GB of space.

For more information on recording programmes, •

see sections “Instant Recording”, “Timeshifting”,

“Electronic Programme Guide”, “Recordings Library”

or “Recording Timers” in the following parts.

Recorded programmes are split into 1GB partitions. •

Names of the stored recordings’ last three digits

indicates this: Such as 4801-000.ts , 4801-001.ts.

Recorded programmes are stored in the following •

directory of the connected USB disk: \DVR\RECS.

All recordings are indicated with a number (such

as 4801-000.ts). A text (txt) ﬁ le is created for each

recording. This text ﬁ le includes information such as

broadcaster, programme, and recording time.

If the writing speed of the connected USB disk is not •

sufﬁ cient, recording may fail and timeshifting feaute

may not be available.

Recordings of HD programmes can occupy bigger •

size on the USB disk depending on the broadcast’s

resolution. For this reason it is recommended

to use USB hard disk drives for recording HD

programmes.

A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 11A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 11 17.08.2011 18:23:3517.08.2011 18:23:35

English - 12 -

Connecting to a DVD Player

via Component Sockets

(YPbPr) or Scart Cable

Some DVD players are connected through •

COMPONENT SOCKETS (YPbPr). In this case,

you must use the supplied Component video

connection cable for enabling connection. First,

plug single jack of the cable to the TV’s YPbPr

socket (side). Afterwards, insert your component

cable’s (not supplied) connectors into the socket

part of the Component video connection cable (see

illustration below). Colours of the connected jacks

should match.

To enable audio connection, use the • VGA/Component

Audio cable. First, plug single jack of the cable

to the TV. Afterwards, insert your DVD player’s

audio cable’s connectors into the socket part of the

VGA/Component audio connection cable (see

illustration below). Colours of the connected jacks

should match.

YPbPr

Side view

DVD Player

Connection Cable

(supplied)

YPbPr Video Cable

(Not supplied)

When the connection is made, switch to •

YPbPr source. See, Input selection section.

Note: To connect YPb Pr device, you should use supplied

component (YPbPr) connection cable

You may also connect through the • SCART input.

SPDIF

SCART

VGA

Coax.OUT

1

Scart Cable

(not supplied)

External device

Note• : These three methods of connection perform the

same function but in different levels of quality. It is not

necessary to connect by all three methods.

Do not plug out the USB/HDD during the recording. •

This may harm the connected USB/HDD.

Only two partitions on a HDD unit can be •

supported.

Some stream packets may not be recorded because •

of signal problems, so sometimes video may freezes

during playback.

Record, Play, Pause, Display (for PlayListDialog) •

keys could not be used when teletext is ON. If a

recording starts from timer when teletext is ON,

teletext is automatically turned off. Also teletext

usage is disabled when there is ongoing recording

or playback.

If the recording time of an event is longer than the

memory capacity, the following message will appear

on the screen: “There is not enough space for ‘event’

but it will be recorded until the drive is full”.

Connecting to a DVD Player via HDMI

Please refer to your DVD player’s instruction book

for additional information. Power off both the TV and

the device before making any connections.

Note: Not all cables shown in the illustration are

supplied.

If your DVD player has an • HDMI socket, you can

connect via HDMI for better video and audio quality.

SPDIF

SCART

VGA

Coax.OUT

1

External device

(not supplied)

HDMI Cable

When you connect to DVD player as illustrated above, •

switch to the connected HDMI source. See, Input

Selection section for more information on changing

sources.

A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 12A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 12 17.08.2011 18:23:3517.08.2011 18:23:35

English - 13 -

Connecting the LCD TV to a PC

For displaying your computer’s screen image on your

LCD TV, you can connect your computer to the TV set.

Power off both computer and display before making

any connections. Use 15-pin D-sub display cable to

connect a PC to the LCD TV. When the connection

is made, switch to PC source. See “Input selection”

section. Set the resolution that suits your viewing

requirements. Resolution information can be found

in the appendix parts

.

PC Input

(back)

Side AV Input

PC VGA Cable

(Not supplied)

PC Audio Cable

(Not supplied)

Side Audio/Video

Connection Cable

(Supplied)

Or

SIDE AV

Using Side AV Connectors

You can connect a range of optional equipment to your

LCD TV using side connectors of the TV.

For connecting a camcorder or camera , you should •

use AV socket (side). To do this, you must use the

supplied video/audio connection cable. First, plug

single jack of the cable to the TV’s AV IN socket

(side). Afterwards, insert your camera cable’s (not

supplied) connectors into the plural part of the video/

audio connection cable. Colours of the connected

jacks should match. See illustration below.

Afterwards, you should switch to • Side AV source. See

the section Input selection in the following sections

for more information.

Camera

AV Connection

Cable (supplied)

AV Cable

(not supplied)

Headphone

SIDE AV

To listen the TV sound from headphones, you •

should connect headphones to your TV by using the

HEADPHONE jack as illustrated above..

Remote Control Handset

Inserting Batteries

Remove the battery cover located on the back of •

the handset by gently pulling backwards from the

indicated part.

Insert two • AAA/R3 or equivalent type batteries

inside. Observe the correct polarity (+/-) when

inserting batteries and replace the battery cover.

Note: Remove the battery from remote control

handset when it is not to be used for a long period.

Otherwise it can be damaged due to any leakage of

batteries. Remote range is approximately 7m/23ft.

Switching On/Off

To Switch the TV On

Connect the power cord to the 220-240V AC 50 Hz.

Switch the “• ” button on the bottom right hand

side under the screen to position “|” so the TV will

switch to standby mode. Then the standby LED

lights up.

To switch on the TV from standby mode either:•

Press the “•

” button, CH / CH or a numeric

button on the remote control.

Press the “•

” or +/- button on the TV.

The TV will then switch on.•

Note : If you switch on your TV via CH

/ CH buttons

on the remote control or on the TV set, the programme

that you were watching last will be reselected.

By either method the TV will switch on.

To Switch the TV to Standby

To switch the TV to low power stand by press the

“

” button on the remote control or right hand side

of the TV.

Note: When the TV is switched to standby mode,

standby LED can blink to indicate that features such

as Standby Search, Over Air Download or Timer is

active.

To Switch the TV Off

Switch the “• ” button on the bottom right hand

side under the screen to position 2 as illustrated,

to isolate the TV from the mains, the LED will

go out.

A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 13A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 13 17.08.2011 18:23:3617.08.2011 18:23:36

English - 14 -

If the TV will not be used for a long period i.e. •

holidays, then unplug the power cord from the

mains socket.

Input Selection

Once you have connected external systems to

your TV, you can switch to different input sources.

Press “SOURCE” button on your remote control

consecutively for directly changing sources.

Basic Operations

You can operate your TV using both the remote

control and onset buttons.

Operation with the Buttons on the TV

Main menu OSD cannot be displayed via control

buttons. “+/-” buttons will function as volume up/down

as default. Even if you set other functions for these

buttons, “+/-” buttons will perform as default after a

short while.

Volume Setting

Press “• P/V/AV” button once and then use “+/-”

buttons to increase or decrease volume, so a volume

level scale (slider) will be displayed on the screen.

While Tv is on, +/- button can use as volume + or

volume - as default.

Programme Selection

Press “• P/V/AV” button once and then use “+/-” buttons

to change channel. By pressing “+/-” button,you can

select the next or previous programme.

AV Mode

Hold the “• P/V/AV” button, source OSD will be displayed

in a few second.

Operation with the Remote Control

The remote control of your TV is designed to control •

all the functions of the model you selected. The

functions will be described in accordance with the

menu system of your TV.

Volume Setting

Press “• V+” button to increase the volume. Press “V-”

button to decrease the volume. A volume level scale

(slider) will be displayed on the screen.

Programme Selection (Previous or Next

Programme)

Press “CH• ” button to select the previous

programme.

Press “CH•

” button to select the next programme.

Programme Selection (Direct Access)

Press numeric buttons on the remote control to select •

programmes between 0 and 9. The TV will switch

to the selected programme. To select programmes

between, press the numeric buttons consecutively.

When the pressing time is due for the second

numeric button, only the ﬁ rst digit programme will

be displayed. Press directly the programme number

to reselect single digit programmes.

Viewing Electronic Programme

Guide (EPG)

You can view the electronic programme guide (EPG)

to view information about available programmes.To

view the EPG menu please press EPG button on the

remote control.

Press “•

”/“ ” buttons to navigate through channels.

Press “•

”/“ ” buttons to navigate through the

programme list.

EPG menu displays available information on all •

channels.

Please note that event information is updated •

automatically. If there are no event information

data available for channels, EPG will be displayed

with blanks.

Up/Down/Left/Right: Navigate.

OK (Options): views/records or sets timer for future

programs.

INFO (Event Details): Displays the programmes in

detail.

Green button: Programme schedule will be listed

A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 14A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 14 17.08.2011 18:23:3717.08.2011 18:23:37

English - 15 -

Yellow button: Display EPG data in accordane with

timeline schedule

Blue button (Filter): Views ﬁ ltering options.

(RECORD): the TV will start to record the

selected progamme. You can press again to stop

the recording.

Up/Down/Left/Right: Navigate.

Red button (Prev Time Slice): Displays the

programmes of previous time slice.

Green button (Next Time Slice): Displays the

programmes of the next time slice.

Yellow button (Prev Day): Displays the programmes

of previous day.

Blue button (Next day): Displays the programmes

of the next day.

Numeric buttons (Jump): Jumps to the preferred

channel directly via numeric buttons.

OK (Options): views/records or sets timer for future

programs.

Text button (Filter): Views ﬁ ltering options.

INFO (Details): Displays the programmes in detail.

(RECORD): the TV will start to record the

selected progamme. You can press again to stop

the recording.

Red button (Prev Day): Displays the programmes

of previous day.

Green button (Next day): Displays the programmes

of the next day.

Yellow button (Zoom): Expands programme

information.

Blue button (Filter): Views ﬁ ltering options.

INFO (Details): Displays the programmes in detail.

Numeric buttons (Jump): Jumps to the preferred

channel directly via numeric buttons.

OK (Options): views/records or sets timer for future

programs.

Text (Search): Displays “Guide Search” menu.

SUBTTL: Press SUBTITLE button to view Select

Genre menu. Using this feature, you can search the

programme guide database in accordance with the

genre. Info available in the programme guide will

be searched and results matching your criteria will

be listed.

SWAP (Now) : Shows the current programme.

Recording via EPG Screen

IMPORTANT: To record a programme, you should

ﬁ rst connect a USB disk to your TV while the TV is

switched off. You should then switch on the TV to

enable recording feature. Otherwise, recording feature

will not be available.

(RECORD): the TV will start to record the

selected progamme. You can press again to stop

the recording.

Note: Switching to a different broadcast or source is

not available during the recording.

/ : Page left / Page right.

Programme Options

In EPG menu, press the OK button to enter the “Event

Options” menu.

Select Channel

In EPG menu, using this option, you can switch to the

selected channel.

Record / Delete Record Timer

IMPORTANT: To record a programme, you should

ﬁ rst connect a USB disk to your TV while the TV is

switched off. You should then switch on the TV to

enable recording feature. Otherwise, recording feature

will not be available.

After you have selected a programme in EPG menu, •

press the OK button and and Options screen will

be displayed. Select “Record” option and press the

OK button. After this operation, a recording becomes

set to the selected programme.

A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 15A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 15 17.08.2011 18:23:3717.08.2011 18:23:37

English - 16 -

To cancel an already set recording, highlight that •

programme and press the OK button and select

the option “Delete Rec. Timer”. The recording will

be cancelled.

Note: You cannot switch to any other channel or

source while there is an active recording on the

current channel.

Set Timer / Delete Timer

After you have selected a programme in EPG menu,

press the OK button and and Options screen will

be displayed. Select “Set Timer on Event” option

and press OK button. You can set a timer for future

programmes.

To cancel an already set reminder, highlight that

programme and press the OK button. Then select

“Delete Timer” option. The timer will be cancelled.

Note: It is not possible to record or set timer for two or

more individual events at the same time interval.

First Time Installation

IMPORTANT: Ensure that the aerial or cable is

connected before switching on the TV for the ﬁ rst

time installation.

When the TV is operated for the ﬁ rst time, installation •

wizard will guide you through the process. First,

language selection screen will be displayed:

Use “• ” or “ ” buttons to select your language

and press OK button to set selected language and

continue.

After selecting the language, “• Welcome!” screen will

be displayed, requiring you to set Country,Teletext

Language and Scan Encrypted options.

By pressing “• ” or “ ” button, select the country

you want to set and press “ ” button to highlight

Teletext Language option. Use “ ” or “ ” button

to select desired Teletext Language.

Press “•

” button after setting Teletext Language

option. Scan Encrypted will be then highlighted.

You can set Scan Encrypted as Yes if you want to

scan coded stations.Afterwards select the desired

Teletext Language.

Press • OK button on the remote control to continue

and the following message will be displayed on the

screen:

To select the “Yes” or “No” option, highlight the item by

using “ ” or “ ” buttons and press OK button.

Afterwards, the following OSD will be displayed on

the screen:

If you select CABLE option, the following screen will

be displayed:

You can select frequency ranges from this screen. For

highlighting lines you see, use “ ” or “ ” button. You

can enter the frequency range manually by using the

numeric buttons on the remote control. Set Start and

Stop Frequency as desired by using numeric buttons

on the remote control. After this operation, you can set

Search Step as 8000 KHz or 1000 KHz. If you select

1000 KHz, the Tv will perform search process in a

detailed way. Searching duration will thus increase

accordingly. When ﬁ nished, press OK button to start

automatic search.

If you select AERIAL option from the Search Type

screen, the television will search for digital terrestrial

TV broadcasts.

A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 16A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 16 17.08.2011 18:23:3717.08.2011 18:23:37

English - 17 -

Note: You can press “MENU” button to cancel.

After all the available stations are stored, Channel •

List will be displayed on the screen. If you like the

sort channels, according to the LCN,please select

“Yes” and than press “OK”.

Press • OK button to quit channel list and watch TV.

Installation

Press “MENU” button on the remote control and

select Installation by using “ ” or “ ” button. Press

OK button and the following menu screen will be

displayed.

Select Automatic Channel Scan (Retune) by using “

”/“ ” button and press OK button. Automatic Channel

Scan (Retune) options will be displayed. You can

select options by using “ ”/“ ” and OK buttons.

Auto Channel Scan (Retune) Menu

Operation

Digital Aerial: Searches and stores aerial DVB

stations.

Digital Cable: Searches and stores cable DVB

stations.

Analogue: Searches and stores analogue stations.

Digital Aerial & Analogue: Searches and stores both

analogue and aerial DVB stations.

Digital Cable & Analogue: Searches and stores both

analogue and cable DVB stations.

Whenever you select an automatic search type and •

press OK button, a conﬁ rmation screen will appear

on the screen. To start installation process, select

Yes, to cancel select No by using .“

” or “ ” and

OK button.

After auto channel scan type is set and selected •

and conﬁ rmed, installation process will start and

progress bar will move along. Press “MENU” button

to cancel process. In such a case, located channels

are not stored.

Manual Tuning

HINT: This feature can be used for direct broadcast

entry.

Select • Manual Channel Scan from the Installation

menu by using “

”/“ ” and OK buttons. Manual

Scan options screen will be displayed.

Select the desired • Search Type using “

” or “

” button. Manual search options will change

accordingly. Use “ ”/“ ” button to highlight an item

and then press “ ” or “ ” button to set an option.

You can press “MENU” button to cancel.

Digital Aerial Manual Search

In manual channel scan, the number of the multiplex

or frequency are entered manually and only that

multiplex or frequency are searched for the channels.

After selecting search type as Digital Aerial, you can

enter the multiplex or frequency number using the

numeric buttons and press OK button to search.

A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 17A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 17 17.08.2011 18:23:3817.08.2011 18:23:38

English - 18 -

Digital Cable Manual Search

In cable manual scan, you can enter frequency,

modulation, symbol rate and network channel scan

options. After selecting search type as Digital Cable,

you can set the desired options and press OK button

to search.

Analogue Manual Search

After selecting search type as analogue, you can use

“ ”/“ ” button to highlight an item and then press “

” or “ ” button to set an option.

Enter the channel number or frequency using the

numeric buttons. You can then press OK button

to search. When the channel is located, any new

channels that are not on the list will be stored.

Analogue Fine Tune

Select • Analogue Fine Tune from the Installation

menu by using “ ” or “ ” and OK buttons. Analogue

ﬁ ne tune screen will be displayed. Analogue Fine

Tune feature will not be available if there are no

analogue channels, digital channels and external

sources stored.

Press • OK button to proceed. Use “

” or “ ” button

to set Fine Tune. When ﬁ nished, press OK button

again.

Network Channel Scan

Select Network Channel Scan from the installation

menu by using “ ” or “ ” and OK buttons. Network

Channel Scan selection screen will be displayed.

Select Digital Aerial or Digital Cable and press

OK button to continue. The following message will

be asked. Select Yes to continue or select No to

cancel.

If you start Digital Aerial scan process, automatic

scanning will start. You can press MENU button to

cancel.

If you start Digital Cable scan process, the following

screen will be displayed.

You can select frequency ranges from this screen. For

highlighting lines you see, use “ ” or “ ” button. You

can enter the frequency range manually by using the

numeric buttons on the remote control. Set Start and

Stop Frequency as desired by using numeric buttons

on the remote control. After this operation, you can set

Search Step as 8000 KHz or 1000 KHz. If you select

1000 KHz, the Tv will perform search process in a

detailed way. Searching duration will thus increase

accordingly. When ﬁ nished, press OK button to start

automatic search. Automatic searching screen will be

displayed during the process.

Note: If you select an extended gap between Start

and Stop frequency rate, automatic search duration

will take a longer time.

Clear Service List (*)

(*) This setting is visible only when the Country option

is set to Denmark, Sweden, Norway or Finland.

Use this setting to clear channels stored. Press “

” or “ ” button to select Clear Service List and then

press OK. The following OSD will be displayed on

the screen:

A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 18A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 18 17.08.2011 18:23:3917.08.2011 18:23:39

English - 19 -

Select YES and press OK to continue or select NO

and press OK button to cancel.

Managing Stations: Channel List

The TV sorts all stored stations in the Channel List.

You can edit this channel list, set favourites or set

active stations to be listed by using the Channel List

options.

Press • “MENU” button to view main menu. Select

Channel List item by using “

” or “ ” button. Press

OK to view menu contents.

Select Edit Channel List to manage all stored

channels. Use “ ” or “ ” and OK buttons to select

Edit Channel List.

Operating the Channel List

Press “• ” or “ ” button to select the channel that

will be processed. Press “ ” or “ ” button to select

a function on Channel List menu.

Use CH•

/CH buttons to move page up or down.

Press • BLUE button to view ﬁ ltering options.

Press • “MENU” button to exit.

Moving a Channel

First select the desired channel. Select Move option •

in the channel list and press OK button.

Edit Number screen will be displayed. Enter the •

desired channel number by using the numeric

buttons on the remote control. If there is a previously

stored channel on that number, a warning screen

will be displayed. Select Yes if you want to move the

channel and press OK.

Press • OK button to process. Selected channel is

now moved.

Deleting a Channel

You can press GREEN button to tag/untag all

channels; YELLOW button to tag/untag channel.

Select the channel that you want to delete and select •

Delete option. Press OK button to continue.

A warning screen will appear. Select • YES to delete,

select No to cancel. Press OK button to continue.

Renaming a Channel

Select the channel that you want to rename and •

select Edit Name option. Press OK button to

continue.

Pressing “•

” or “ ” button moves to the previous/

next character. Pressing “ ” or “ ” button toggles

the current character, i.e., ‘b’ character becomes ‘a’

by “ ” and ‘c’ by “ ”. Pressing the numeric buttons

‘0...9’ replaces the highlighted character with the

characters printed above the button one by one as

the button is pressed.

When ﬁ nished, press • OK button to save. Press

“MENU” to cancel.

Locking a Channel

You can press GREEN button to tag/untag all

channels; YELLOW button to tag/untag a single

channel.

Select the channel that you want to lock and select •

Lock option. Press OK button to continue.

You will be asked to enter parental control PIN. •

Default PIN is set as 0000. Enter the PIN number.

Press • OK button when the desired channel is

highlighted to lock/unlock the channel. Lock symbol

will be displayed next to the selected channel.

A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 19A01_MB60_[GB]_(01-TV)_1910UK_IDTV_TC_PVR_BRONZE17_24942LED_YPBPR_ROCKER_10072635_50186851.indd 19 17.08.2011 18:23:3917.08.2011 18:23:39

La page charge ...

Sharp LC-24DV510E Le manuel du propriétaire

Ce manuel convient également à

Sharp LC-24DV510E Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents