Klein Tools CL900 Manuel utilisateur

INSTRUCTION MANUAL

ENGLISH

FRANÇAIS pg. 33

ESPAÑOL pg. 17

2000A

Digital Clamp Meter

1000V

2000A

60M

Ω

True RMS

Measurement

Technology

• NON-CONTACT

VOLTAGE TESTING

• INRUSH CURRENT

• LOW IMPEDANCE

• DATA HOLD

• RANGE HOLD

• AUDIBLE

CONTINUITY

• DIODE TEST

• CAPACITANCE

• FREQUENCY

2

m IP40

CL900

4007177

2

GENERAL SPECIFICATIONS

Klein Tools CL900 is an auto-ranging, true root mean square (TRMS)

digital clamp meter that measures AC/DC current via the clamp and

measures AC/DC voltage, resistance, continuity, frequency, duty-

cycle, capacitance, and tests diodes via test-leads. It features a Low

Impedance (LoZ) mode for identifying and eliminating ghost or stray

voltages, and has a dedicated mode for capturing Inrush Current.

• Operating Altitude: 6562 ft. (2000m)

• Relative Humidity: <80% non-condensing

• Operating Temperature: 32° to 122°F (0° to 50°C)

• Storage Temperature: 14° to 140°F (-10° to 60°C)

• Accuracy: Values stated at 65° to 83°F (18° to 28°C)

• Temp Coefcient: 0.1 x (Quoted Accuracy) per °C above

28°C or below 18°C, corrections are required when ambient

working temp is outside of Accuracy Temp range

• Dimensions: 10.4" x 3.9" x 1.7" (265 x 99 x 43 mm)

• Weight: 18.6 oz. (526 g) including batteries

• Calibration: Accurate for one year

• Standards: Conforms to UL STD 61010-1, 61010-2-032,

61010-2-033.

Certified to CSA STD C22.2 # 61010-1,

61010-2-032, 61010-2-033.

IEC EN 61010-1, 61010-2-032,

61010-2-033.

• Pollution degree: 2

• Accuracy: ± (% of reading + # of least significant digits)

• Drop Protection: 6.6 ft. (2m)

• Safety Rating: CAT IV 600V, CAT III 1000V, Class 2,

Double insulation

CAT III: Measurement category III is applicable to test and

measuring circuits connected to the distribution part of the

building’s low-voltage MAINS installation.

CAT IV: Measurement category IV is applicable to test and

measuring circuits connected at the source of the building’s

low-voltage MAINS installation.

• Electromagnetic Environment: IEC EN 61326-1. This

equipment meets requirements for use in basic and controlled

electromagnetic environments like residential properties,

business premises, and light-industrial locations.

Specifications subject to change.

ENGLISH

3

ELECTRICAL SPECIFICATIONS

Function Range Resolution Accuracy (50/60 Hz)

AC Voltage

(V AC)

600.0mV 0.1mV ±(1.0% + 8 digits)*

6.000V 1mV ±(1.0% + 5 digits)

60.00V 10mV

±(1.2% + 5 digits)

600.0V 0.1V

1000V 1V ±(1.5% + 5 digits)

DC Voltage

(V DC)

600.0mV 0.1mV ±(0.9% + 8 digits)

6.000V 1mV

±(1.0% + 3 digits)60.00V 10mV

600.0V 0.1V

1000V 1V ±(1.2% + 3 digits)

Input Impedance:

10MΩ

Frequency Range:

50 to 400Hz

Maximum Input: 1000V AC RMS or 1000V DC

*Accuracy specified from 5% to 100% of the measuring range

AC Current

(A) TRMS

600.0A 0.1A ±(2.0% + 5 digits)

2000A 1A ±(2.5% + 8 digits)

DC Current (A)

600.0A 0.1A ±(2.0% + 5 digits)

2000A 1A ±(2.5% + 8 digits)

AC Frequency Range: 50 to 60Hz , >500mA

DC:

>200mA (low current requires use of DC ZERO function)

AC Current (A)

Inrush

600A 0.1A ±(2.5% + 5 digits)**

2000A 1A ±(3.0% + 8 digits)**

AC Frequency Range: 50 to 60Hz

when auto-ranging >3A detectable

(>2A if held in 600A range)

**Accuracy specified assumes AC sine wave

Resistance

600.0Ω 0.1Ω

±(1.5% + 5 digits)

6.000KΩ 1Ω

60.00kΩ 10Ω

600.0kΩ 100Ω

6.000MΩ 1kΩ

60.00MΩ 10kΩ ±(2.0% + 10 digits)

Maximum Input: 600V AC RMS or 600V DC

Capacitance

60.00nF 10pF ±(5.0% + 35 digits)

600.0nF 0.1nF

±(3.0% + 5 digits)

6.000µF 1nF

60.00µF 10nF

600.0µF 0.1µF

6000µF 1µF ±(5.0% + 5 digits)

Maximum Input: 600V AC RMS or 600V DC

4

ENGLISH

WARNINGS

To ensure safe operation and service of the meter, follow these instructions.

Failure to observe these warnings can result in severe injury or death.

• Before each use, verify meter operation by measuring a known voltage

or current.

• Never use the meter on a circuit with voltages that exceed the category

based rating of this meter.

• Do not use the meter during electrical storms or in wet weather.

• Do not use the meter or test leads if they appear to be damaged.

• Use only with CAT III or CAT IV rated test leads.

• Ensure meter leads are fully seated, and keep fingers away from the

metal probe contacts when making measurements.

• Use caution when working with voltages above 25V AC RMS or

60V DC. Such voltages pose a shock hazard.

• To avoid false readings that can lead to electrical shock, replace batteries

when a low battery indicator appears.

• Do not attempt to measure resistance or continuity on a live circuit.

• Do not hold meter above hand & finger guard during use.

ELECTRICAL SPECIFICATIONS

Frequency

9.999Hz 0.001Hz

±(1.0% + 5 digits)

99.99Hz 0.01Hz

999.9Hz 0.1Hz

9.999kHz 1Hz

99.99kHz 10Hz

500.0kHz 100Hz

Sensitivity: >8V RMS, Maximum Input: 600V DC or 600V AC RMS

Duty Cycle

0.1% – 99.9% 0.10%

±(1.2% + 2 digits)

Pulse width: 0.1ms – 100ms

Frequency width: 5Hz to 10kHz

Sensitivity: >8V RMS

Maximum Input: 600V AC RMS or 600V DC

OTHER MEASUREMENT APPLICATIONS

• Diode Test: Max. 1.5mA, open circuit voltage ~ 3.0V DC

• Continuity Check: Audible signal <50Ω, test current <0.35mA

• Sampling Frequency: 3 samples per second

• Low Impedence (Low Z): Input impedence: >3kΩ

Max input: 600V RMS

• Auto Power off: After ~30 minutes of inactivity

• Overload:

"OL" indicated on display, overload protection

1000V RMS in Voltage setting, 600V RMS in all other settings

• Polarity: "-" on display indicates negative polarity

• Non-Contact Voltage Detection:

>90V AC

• Display: 3-5/6 digit, 6000 Count LCD

5

SYMBOLS ON METER

Alternating Current (AC) Direct Current (DC)

A

Amperage

V

Voltage

Audible Continuity

Hz

Frequency

Diode Test

%

Duty-Cycle

Capacitance Low Impedance

Resistance (Ohms) DC Current Zero Function

+ Positive – Negative

COM

Common Ground

Double Insulated Class II

Warning or Caution:

To ensure safe operation and service of this

meter, follow all warnings and instructions detailed in this manual.

Risk of Electrical Shock:

I

mproper use of this meter can lead to risk of

electrical shock. Follow all warnings and instructions detailed in this manual.

SYMBOLS ON LCD

AC Measurement DC Measurement

Negative Reading Data Hold

AUTO

Auto Ranging

MAX

Maximum Value Hold

MIN

Minimum Value Hold Low Battery

Auto Power Off Audible Continuity

Diode Test Inrush Current

k

kilo (value x 10

3

)

m

mili (value x 10

-3

)

M

Mega (value x 10

6

)

n

nano (value x 10

-9

)

μ

micro (value x 10

-6

)

F

Farads

Ohms

A

Amps

V

Volts

LoZ

Low Impedence

Hz

Frequency (Hertz)

%

Duty Cycle

WARNINGS

• Always adhere to local and national safety codes. Use personal

protective equipment to prevent shock and arc blast injury where

hazardous live conductors are exposed.

• Usage of this meter in any way other than that specified by the

manufacturer can impair safe operation, resulting in severe injury or death.

• To avoid risk of electric shock, disconnect leads from any voltage source

before removing battery door.

• To avoid risk of electric shock, do not operate meter while battery door is

removed.

6

ENGLISH

FEATURE DETAILS

1

9

7

2

3

11

10

13

14

15

16

54

8

6

NOTE: There are no user-serviceable parts inside meter.

12

1.

6000 count

LCD display

2.

Function

selector

switch

3.

Clamp

4.

"COM" jack

5.

"VΩ" jack

6.

Data Hold /

Backlight

button

7.

"RANGE"

button

8.

"MAX/MIN"

button

9.

SEL (select) /

DC Zero button

10.

INRUSH button

11.

Clamp trigger

(press to open

clamp)

12.

Arrow markings

13.

N

on-contact

Voltage Testing

Button

14.

N

on-contact

Voltage Testing

Sensor

15.

N

on-contact

Voltage Testing

LED Indicator

16.

Polarity markings

(for DC current)

7

FUNCTION BUTTONS

ON/OFF

To power ON the meter, rotate the Function Selector switch

2

from

the OFF setting to any measurement setting. To power OFF the meter,

rotate the Function Selector switch

2

to the OFF setting. By default,

the meter will automatically power OFF after aprox. 30 minutes of

inactivity. To deactivate the auto power OFF functionality, press and

hold the "SEL/DC ZERO" button

9

before powering ON from the OFF

setting. When auto power OFF is deactivated, the Auto Power Off icon

will not be visible in the display.

SEL (SELECT) / DC ZERO BUTTON (FOR SECONDARY FUNCTIONS)

The SEL/DC ZERO button

9

activates the secondary function for

each application accessible by the function selector switch

2

:

• In Current

A

and Low Impedance modes, it toggles between

AC and DC measurements.

• In Frequency/Duty Cycle

setting, it toggles between these

measurements

.

• In Continuity/Resistance/Diode-Test

setting, it toggles

through these measurements in order

.

• In DC current setting, pressing and holding for more than one

second initiates the DC ZERO function. Subsequent DC current

measurements automatically subtract the measurement that was

present as an offset correction.

The default function for each application is printed on the meter in

white, the secondary functions in orange. An icon on the LCD display

will indicate which function is active.

DATA HOLD

Press the Data Hold / Backlight button

6

to hold the measurement

on the display. Press again to release the display to return to live

measuring.

BACKLIGHT

Press and hold the Data Hold / Backlight button

6

for more than

one second to turn ON the backlight. The backlight will automatically

power OFF after 3 minutes of inactivity.

RANGE

The meter defaults to auto-ranging mode

AUTO

. This mode

automatically determines the most appropriate measurement range

for the testing that is being conducted. To manually force the meter to

measure in a different range, use the Range button

7

.

1. Press the "RANGE" button

7

to manually select measurement

range (AUTO is deactivated on the LCD). Repeatedly press the

"RANGE" button

7

to cycle through the available ranges, stopping

once the desired range is reached.

2. To return to auto-ranging mode, press and hold the "RANGE"

button

7

for more than one second (AUTO is reactivated).

8

ENGLISH

FUNCTION BUTTONS

MAX/MIN

When the "MAX/MIN" button

8

is pressed, the meter keeps track of

the Maximum and Minimum values as the meter continues to take

samples.

1. When measuring, press "MAX/MIN" button

8

to toggle between

the Maximum value (MAX) and Minimum value (MIN). If a new

Maximum or Minimum, the display will update with the new value.

2. Press "MAX/MIN" button

8

for more than one second to return to

normal measuring mode.

INRUSH CURRENT

Rotate the Function Selector switch

2

to the Current

A

setting

and

press INRUSH

10

prior to an inrush event to test for inrush

current. While the meter monitors current waiting for the inrush

event, "----" will be visible on the display.

NON-CONTACT VOLTAGE TESTING

Press and hold the "NCV" button

13

to test for AC voltage using the

integrated non-contact voltage tester. Approach the conductor under

test leading with the sensing antenna

14

. The meter delivers visual

warning signals via the LED indicator

15

and audible signals (beeps)

when AC voltage is detected. Release the "NCV" button to exit NCV

testing mode.

NOTE: It is not recommended to perform continuity and NCV testing

simultaneously, as both tests utilize the same audible signal, making

it difficult to resolve which test is responsible for the audible alarm.

NOTE: Only voltages of 90V AC or greater will be detected.

9

OPERATING INSTRUCTIONS

CONNECTING TEST LEADS

Do not test if leads are improperly seated. Results could cause

intermittent display readings. To ensure proper connection, firmly

press leads into the input jack completely.

TESTING IN CAT III / CAT IV MEASUREMENT LOCATIONS

Ensure the test lead shield is pressed firmly in place. Failure to use

the CATIII / CATIV shield increases arc-flash risk.

TESTING IN CAT II MEASUREMENT LOCATIONS

CAT III / CAT IV shields may be removed for CAT II locations. This

will allow testing on recessed conductors such as standard wall

outlets. Take care not to lose the shields.

5/32"

(4 mm)

.7" (18 mm)

INCORRECT

CORRECT

10

OPERATING INSTRUCTIONS

AC/DC CURRENT (LESS THAN 2000A)

AC Current is measured by pressing the

clamp trigger

11

to open the clamp

3

and placing it around a current-carrying wire.

When measuring, care should be taken to

ensure that the clamp

3

is completely

closed with trigger

11

fully released, and

that the wire passes perpendicularly through

the center of the clamp

3

in line with the

arrow markings

12

.

To measure current:

1. Rotate the Function Selector switch

2

to

the

Current

A

setting

.

2. The meter defaults to AC measurement.

To

measure DC, press the "SEL/DC ZERO"

button

9

to toggle between AC and DC

modes. The AC or DC icon on the LCD

indicates which mode is selected. Note

"AC" or "DC" on the display.

3. Place the clamp

3

around the wire. When measuring DC current,

align the polarity markings

16

on the clamp with the polarity of

the wire to avoid negative readings. The current measurement will

be shown in the display.

The meter will auto-range to display the

measurement in the most appropriate range.

To measure inrush current:

1. Rotate the Function Selector switch

2

to the Current

A

setting.

Place the clamp

3

around the wire and press "INRUSH"

10

. The

Display

1

will show "----". Initiate the Inrush event and the inrush

current will be captured and presented in the display. A second press of

"INRUSH"

10

will reset the Inrush measurement, "----" will be presented

on the display and the meter will wait for the next Inrush event.

NOTE: The Inrush measurement period is 100 milliseconds, with a 20

millisecond sampling rate.

2. P

ress and hold

"INRUSH"

10

for more than one second to return to

normal measuring mode.

Disconnect test leads when measuring with the clamp.

NOTE: If non-zero values are displayed prior to measuring in DC

current mode, an offset correction may be required to improve

accuracy. With meter in DC current mode, press and hold the

"SEL/DC ZERO" button

9

for more than one second to initiate the

DC current ZERO function. Subsequent DC current measurements

automatically subtract the measurement that was initially present as

an offset correction.

ENGLISH

WIRE

11

OPERATING INSTRUCTIONS

AC/DC VOLTAGE (LESS THAN 1000V)

1. Insert RED test lead into VΩ jack

5

, and BLACK test lead into

COM jack

4

, and rotate function selector switch

2

to the

AC voltage V or DC voltage V setting. The AC or DC icon on

the LCD indicates which setting is selected.

2. Apply test leads to the circuit to be tested to measure voltage.

The meter will auto-range to display the measurement in the

most appropriate range.

NOTE: If "–" appears on the LCD, the test leads are being applied to

the circuit in reverse. Swap the position of the leads to correct this.

NOTE: When in a voltage setting and the test leads are open,

readings of order mV may appear on the display. This is noise and

is normal. By touching the test leads together to close the circuit

the meter will measure zero volts.

Do not attempt to measure voltages greater than 1000V

in any Voltage setting.

AC/DC LoZ VOLTAGE (LESS THAN 600V)

1. Insert RED test lead into VΩ jack

5

, and BLACK test lead into

COM jack

4

, and rotate function selector switch

2

to the

AC/DC LoZ voltage

setting.

The meter defaults to AC

measurement.

To measure DC, press the "SEL/DC ZERO" button

9

to toggle between AC and DC modes. The AC or DC icon on

the LCD indicates which mode is selected. Note "AC" or "DC" on

the display.

2. Apply test leads to the circuit to be tested to measure voltage.

The meter will auto-range to display the measurement in the

most appropriate range.

Do not attempt to measure voltages greater than 600V

in LoZ setting.

Black lead Red lead

-or-

12

ENGLISH

RESISTANCE MEASUREMENTS

1. Insert RED test lead into VΩ jack

5

, and BLACK test lead into

COM jack

4

, and rotate function selector switch

2

to the

Continuity/Resistance/Diode-Test

setting.

NOTE: The meter defaults to Continuity testing in this mode. Press

the SEL/DC ZERO" button

9

once to enter Resistance testing

mode. The Resistance icon

will appear on the display.

2. Remove power from circuit.

3. Measure resistance by connecting test leads to circuit. The

meter will auto-range to display the measurement in the most

appropriate range.

NOTE: When in a Resistance setting and the test leads are open

(not connected across a resistor), or when a failed resistor is under

test, the display will indicate O.L. This is normal.

DO NOT attempt to measure resistance on a live circuit.

CONTINUITY

1. Insert RED test lead into VΩ jack

5

, and BLACK test lead into

COM jack

4

, and rotate function selector switch

2

to the

Continuity/Resistance/Diode-Test

setting.

NOTE: The meter defaults to Continuity testing in this setting.

Ensure that the Continuity Testing icon

is visible on the display.

If not, press the "SEL/DC ZERO" button

9

repeatedly until the

icon is shown.

2. Remove power from circuit.

3. Test for continuity by connecting conductor or circuit with test

leads. If resistance is measured less than 50Ω, an audible signal

will sound and display will show a resistance value indicating

continuity. If circuit is open, display will show "OL".

DO NOT attempt to measure continuity on a live circuit.

OPERATING INSTRUCTIONS

Black lead Red lead

13

DIODE TEST

1. Insert RED test lead into VΩ jack

5

, and BLACK test lead into

COM jack

4

, and rotate function selector switch

2

to the

Continuity/Resistance/Diode-Test

setting.

NOTE: The meter defaults to Continuity testing in this mode. Press

the SEL/DC ZERO" button

9

twice to enter Diode testing mode. The

Diode icon will appear on the display.

2. Touch test leads to diode. A reading of 200-800mV on display

indicates forward bias, "OL" indicates reverse bias. An open

device will show "OL" in both polarities. A shorted device will

show approximately 0mV.

FREQUENCY / DUTY-CYCLE

1. Insert RED test lead into VΩ jack

5

and BLACK test lead into

COM jack

4

, and rotate function selector switch

2

to the

Frequency/Duty-Cycle

setting.

OPERATING INSTRUCTIONS

NOTE: : The meter defaults to Frequency testing. To test Duty-Cycle,

press the "SEL/DC ZERO" button

9

once. Ensure that the appropriate

icon (either Hz or %) appears on the display.

1. Measure by connecting test leads across the circuit.

Black lead Red lead

14

OPERATING INSTRUCTIONS

CAPACITANCE

1. Insert RED test lead into VΩ jack

5

, and BLACK test lead into

COM jack

4

, and rotate function selector switch

2

to the

Capacitance

setting.

2. Remove power from circuit.

3. Measure capacitance by connecting test leads across the capacitor.

The meter will auto-range to display the measurement in the most

appropriate range.

ENGLISH

MAINTENANCE

BATTERY REPLACEMENT

When indicator is displayed on LCD, batteries must be replaced.

1. Loosen screw on battery door.

2. Replace 2 x AAA batteries (note proper polarity).

3. Replace battery door and fasten securely with screw.

T

o avoid risk of electric shock, disconnect leads from any voltage

source before removing battery door.

To avoid risk of electric shock, do not operate meter while

battery door is removed.

Black lead Red lead

15

CLEANING

Be sure meter is turned off and wipe with a clean, dry lint-free

cloth.

Do not use abrasive cleaners or solvents.

STORAGE

Remove the batteries when meter is not in use for a prolonged

period of time. Do not expose to high temperatures or

humidity. After a period of storage in extreme conditions

exceeding the limits mentioned in the General Specifications

section, allow the meter to return to normal operating

conditions before using.

WARRANTY

www.kleintools.com/warranty

DISPOSAL / RECYCLE

Do not place equipment and its accessories in the trash.

Items must be properly disposed of in accordance with local

regulations. Please see www.epa.gov or www.erecycle.org

for additional information.

CUSTOMER SERVICE

KLEIN TOOLS, INC.

450 Bond Street

Lincolnshire, IL 60069

1-877-775-5346

[email protected]

www.kleintools.com

NOTES

KLEIN TOOLS, INC.

450 Bond Street

Lincolnshire, IL 60069

1-877-775-5346

[email protected]

www.kleintools.com

ENGLISH

ESPAÑOL

MANUAL DE INSTRUCCIONES

Multímetro digital de

gancho de 2000A

True RMS

Tecnología de

medición

• PRUEBA DE VOLTAJE

SIN CONTACTO

• CORRIENTE DE

INSERCIÓN

• BAJA IMPEDANCIA

• RETENCIÓN DE DATOS

• RETENCIÓN DE RANGO

• CONTINUIDAD POR

INDICADOR AUDIBLE

• PRUEBA DE DIODO

• CAPACITANCIA

• FRECUENCIA

1000V

2000A

60M

Ω

2

m IP40

CL900

4007177

18

ESPAÑOL

ESPECIFICACIONES GENERALES

Klein Tools CL900 es un multímetro digital de gancho de rango automático

con media cuadrática real (TRMS) que mide corriente CA/CD con la pinza;

mide voltaje CA/CD, resistencia, continuidad, frecuencia, ciclo de servicio y

capacitancia; y prueba diodos con cables de prueba. Cuenta con un modo

de baja impedancia (LoZ) para identificar y eliminar voltajes fantasma o

erráticos, y tiene un modo dedicado para capturar la corriente de inserción.

• Altitud de funcionamiento: 6562pies (2000m)

• Humedad relativa: <80 % sin condensación

• Temperatura de operación: 32°F a 122°F (0°C a 50°C)

• Temperatura de almacenamiento: 14°F a 140°F (-10°C a 60°C)

• Precisión: Valores establecidos según una temperatura ambiente de

65°F a 83°F (18°C a 28°C)

• Coeciente de temperatura: 0,1 × (precisión indicada) por cada

°C por encima de los 28°C o por debajo de los 18°C, es necesario

realizar correcciones si la temperatura del ambiente de trabajo se

encuentra fuera del rango de precisión de temperatura

• Dimensiones: 10,4" × 3,9" × 1,7" (265mm × 99mm × 43 mm)

• Peso: 18,6 oz (526 g) incluidas las baterías

• Calibración: Precisa durante un año

• Normas: Cumple con las normas UL 61010-1, 61010-2-032

y 61010-2-033.

Certificado según las normas CSA C22.2 N.° 61010-1,

61010-2-032 y 61010-2-033.

IEC EN 61010-1, 61010-2-032,

61010-2-033.

• Grado de contaminación: 2

• Precisión: ± (% de lectura + cantidad de dígitos menos significativos)

• Protección ante caídas: 6,6pies (2m)

• Clasicación de seguridad: CATIV 600V, CATIII 1000V, clase2,

doble aislamiento

CATIII: La categoría III de medición es aplicable a los circuitos de

medición y prueba conectados a la distribución de la instalación de

red de bajo voltaje de un edificio.

CATIV: La categoría IV de medición es aplicable a los circuitos de

medición y prueba conectados a la fuente de la instalación de red de

bajo voltaje de un edificio.

• Entorno electromagnético: IEC EN 61326-1. Este equipo cumple con

los requisitos apropiados para su uso en entornos electromagnéticos

básicos y controlados, como propiedades residenciales,

establecimientos comerciales e instalaciones de industria ligera.

Especificaciones sujetas a cambios.

19

ESPECIFICACIONES ELÉCTRICAS

Función Rango Resolución Precisión

(50Hz/60Hz)

Voltaje CA

(V CA)

600,0mV 0,1mV ± (1,0% + 8 dígitos)*

6,000V 1mV ± (1,0% + 5 dígitos)

60,00V 10mV

± (1,2% + 5 dígitos)

600,0V 0,1V

1000V 1V ± (1,5% + 5 dígitos)

Voltaje CD

(V CD)

600,0mV 0,1mV ± (0,9% + 8 dígitos)

6,000V 1mV

± (1,0% + 3 dígitos)60,00V 10mV

600,0V 0,1V

1000V 1V ± (1,2% + 3 dígitos)

Impedancia de entrada: 10MΩ Rango de frecuencia: 50Hz a 400Hz

Entrada máxima: 1000V CA RMS o 1000V CD

*Precisión especificada de 5% a 100% del rango de medición

Corriente CA

(A) TRMS

600,0A 0,1A ± (2,0% + 5 dígitos)

2000A 1A ± (2,5% + 8 dígitos)

Corriente CD (A)

600,0A 0,1A ± (2,0% + 5 dígitos)

2000A 1A ± (2,5% + 8 dígitos)

Intervalo de frecuencia de CA: 50Hz a 60Hz, >500mA

CD: >200mA (la corriente baja requiere el uso de la función "DC ZERO"

[CD CERO])

Corriente de

inserción (A)

de CA

600A 0,1A ± (2,5% + 5 dígitos)**

2000A 1A ± (3,0% + 8 dígitos)**

Intervalo de frecuencia de CA: 50Hz a 60Hz cuando el rango

automático es >3A detectable (>2A si se mantiene en un rango

de 600A)

**La precisión especificada supone una onda sinusoidal de CA

Resistencia

600,0Ω 0,1Ω

± (1,5% + 5 dígitos)

6,000kΩ 1Ω

60,00kΩ 10Ω

600,0kΩ 100Ω

6,000MΩ 1kΩ

60,00MΩ 10kΩ ± (2,0% + 10 dígitos)

Entrada máxima: 600V CA RMS o 600V CD

Capacitancia

60,00nF 10pF ± (5,0% + 35 dígitos)

600,0nF 0,1nF

± (3,0% + 5 dígitos)

6,000µF 1nF

60,00µF 10nF

600,0µF 0,1µF

6000µF 1µF ± (5,0% + 5 dígitos)

Entrada máxima: 600V CA RMS o 600V CD

20

ESPAÑOL

ADVERTENCIAS

Para garantizar un funcionamiento y servicio seguros del medidor, siga

estas instrucciones. El incumplimiento de estas advertencias puede

provocar lesiones graves o la muerte.

• Antes de cada uso, verifique el funcionamiento del multímetro midiendo un

voltaje o corriente conocidos.

• Nunca debe utilizar este multímetro en un circuito con voltajes que excedan la

clasificación correspondiente a la categoría del multímetro.

• No utilice el multímetro durante tormentas eléctricas o en clima húmedo.

• No utilice el multímetro o los cables de prueba si en apariencia están dañados.

• Utilice el multímetro con cables de prueba con clasificación CAT III o CAT IV

únicamente.

• Asegúrese de que los cables del multímetro estén correctamente colocados y

mantenga los dedos lejos de los contactos de la sonda de metal al realizar las

mediciones.

• Proceda con precaución cuando trabaje con voltajes superiores a 25V CA RMS

o 60V CD. Esos voltajes implican un riesgo de choque eléctrico.

• Para evitar lecturas falsas que puedan provocar choques eléctricos, reemplace

las baterías cuando aparezca el indicador de batería baja.

ESPECIFICACIONES ELÉCTRICAS

Frecuencia

9,999Hz 0,001Hz

± (1,0% + 5 dígitos)

99,99Hz 0,01Hz

999,9Hz 0,1Hz

9,999kHz 1Hz

99,99kHz 10Hz

500,0kHz 100Hz

Sensibilidad: > 8V RMS, Entrada máxima: 600V CD o 600V CA RMS

Ciclo de

servicio

0,1% – 99,9% 0,10%

± (1,2% + 2 dígitos)

Ancho de pulso: 0,1ms – 100ms

Ancho de frecuencia: 5Hz a 10kHz

Sensibilidad: >8V RMS

Entrada máxima: 600V CA RMS o 600V CD

OTRAS APLICACIONES DE MEDICIÓN

• Prueba de diodo:

1,5mA máx., 3,0V CD de voltaje de circuito abierto aprox.

• Vericación de continuidad: Señal audible <50Ω, <0,35mA de

corriente de prueba

• Frecuencia de muestreo: 3 muestras por segundo

• Baja impedancia (Low Z): Impedancia de entrada: > 3kΩ

Entrada máx.: 600VRMS

• Apagado automático: después de aprox. 30minutos de inactividad

• Sobrecarga: Se indica "OL" (SOBRECARGA) en pantalla, protección

contra sobrecarga de 1000V RMS en posición de voltaje,

600V RMS en las demás posiciones

• Polaridad: "-" en pantalla indica polaridad negativa

• Detección de voltaje sin contacto: > 90V CA

• Pantalla: LCD de 3-5/6dígitos con recuento de 6000

La page est en cours de chargement...

Klein Tools CL900 Manuel utilisateur

Klein Tools CL900 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents