Ideal 61-405 Manuel utilisateur

Instrucciones en español adentro / Instructions en français à l’intérieur

61-415 200-Amp AC/DC

61-405 200-Amp AC

TightSight™ Fork Meter

Operation and Safety Manual

IDEAL

®

Test and Measurement

Introduction ......................................................................3

Contacting IDEAL INDUSTRIES, INC ..........................................3

Safety Information ...............................................................4

Warnings ................................................................................................... 4-5

Cautions ........................................................................................................ 5

Symbols .................................................................................................... 6-7

Operation......................................................................8-23

Identification and description of operating controls and functions ........... 8-9

Operating Features ............................................................................... 10-11

Using Test Leads ........................................................................................12

Meter Operation ................................................................................... 13-17

Non-Contact Voltage Testing...........................................................13

Measuring Current .......................................................................... 14

Measuring Voltage ..........................................................................14

Measuring Continuity .....................................................................15

Measuring Resistance ..................................................................... 15

Measuring Capacitance ...................................................................16

Measuring Diodes ...........................................................................16

Measuring Frequency .....................................................................17

Measuring Temperature ..................................................................17

Functions Operation Table .................................................................... 18-19

Functions Indication Table .................................................................... 20-21

Electrical Specifications ........................................................................ 22-23

Environmental Specifications ................................................ 24

Mechanical Specifications ................................................... 24

EMC / EMI ....................................................................... 24

FCC ............................................................................... 25

Safety ............................................................................ 25

Maintenance and Service ................................................ 26-27

Table of Contents

2

Introduction

The IDEAL

®

61-415 TightSight™ and 61-405 Fork Meters are auto ranging true

root mean square (TRMS) digital fork meters that measure AC and DC current

(amps (61-415)) via the forks, measure voltage, resistance, continuity, capacitance,

diode via test-leads, and detects the presence of voltage between 40V to 600V AC

via a non-contact sensor in the right tip of the clamp.

Contacting IDEAL INDUSTRIES, INC.

To contact IDEAL INDUSTRIES, INC., call one of the following telephone numbers:

IDEAL Industries USA Customer Service

• Phone Number: 800-435-0705

• Email: [email protected]

IDEAL Industries Canada Customer Service

• Phone Number: 905-683-3400

• Email: [email protected]

IDEAL Industries EMEA

• Phone Number: +44 (0)1925 444 446

• Email: eur[email protected]

IDEAL Industries Australia

• Phone Number: +61 3 9562 0175

• Email: [email protected]

Or visit the IDEAL Electrical Website at www.idealind.com

To register your product, find manuals, watch videos, simply scan this QR code.

3

Arc Flash and Shock Hazard, Proper PPE Required. Follow all safety procedures,

wear proper PPE in accordance to NFPA 70E. Read and fully understand the

instruction manual prior to using this product. Failure to comply can result in

serious injury or death.

Warning - Identifies conditions and actions that could result in

possible death or serious injury if the hazard is realized.

Caution - Identifies conditions and actions that could result in meter

damage, equipment under test damage or data loss if the hazard is realized.

WARNING

Safety Information

Arc Flash and Shock Hazard, Proper PPE Required. Follow all safety procedures,

wear proper PPE in accordance to NFPA 70E and follow the guidelines below and

the instructions in this manual when operating the meter. Failure to comply can

result in serious injury or death.

• Choking Hazard, Small Parts. Keep Away from Children. Sharp Objects

Hazard, This is not a toy. It is not for use or play by children. Keep Away

from Children. Failure to do so can result in serious injury.

• Only experienced or technically competent consumers should use this

equipment. When in doubt, call an experienced electrician to make any and

all necessary repairs or installations. At all times, perform any necessary

work on a de-energized circuit that has had its circuit breaker turned off and

has been locked out.

• Use the Meter only as specified in this manual or protection provided by the

Meter can be compromised.

• Before using or connecting the Meter, visually inspect it to ensure the cases

are not cracked and the back case is securely in place. Do not use if the

Meter appears damaged.

• Before using the test leads, inspect carefully for damaged insulation,

exposed metal or cracked probes. Check test leads for continuity. Do not use

leads if they appear damaged.

• Use only approved test leads. Do not use improvised connections that could

present a safety hazard.

• Never measure current (amps) while the test leads are inserted into the input

jacks.

• When using the probes, keep fingers behind the finger guards on the

probes.

• Connect the common test lead before connecting the live test lead. When

disconnecting test leads, disconnect the live test lead first.

• This Meter is intended for use by qualified electricians. Follow NFPA 70E

Standards for Electrical Safety in the Workplace when using this Meter.

• Do not use without the batteries correctly in place and the battery door

closed and secured.

• Do not use Meter if it operates incorrectly as protection may be

compromised. When in doubt, have the Meter serviced.

• When servicing the Meter, use only specified replacement parts.

4

Arc Flash and Shock Hazard, Proper PPE Required. Follow all safety procedures,

wear proper PPE in accordance to NFPA 70E and follow the guidelines below and

the instructions in this manual when operating the meter. Failure to comply can

result in serious injury or death.

• Have the Meter serviced only by qualified service personnel.

• Do not use the Meter around explosive gas, dust, or vapor, or during

electrical storms, or in wet environments.

• When measuring, keep fingers behind the Tactile Barrier. See “The Meter”

on pg. 8 and 9.

• Do not apply more than the rated voltage, as marked on the Meter, between

the terminals or between any terminal and earth ground.

• To avoid false readings that can lead to electrical shock and injury, replace

the batteries as soon as the low battery indicator ( ) appears.

• Remove the test leads from the circuit prior to removing the battery door.

• Voltages exceeding 30VAC RMS or 60VDC pose a shock hazard so use

caution.

• Always ensure that test leads are secured so that they cannot be accidentally

snagged or tripped over.

• Do not work alone so that assistance can be rendered in an emergency.

• Use extreme caution when working around bare conductors or bus bars.

Contact with the conductor could result in electric shock.

• Adhere to local and national safety codes. Individual protective equipment

must be used to prevent shock and arc blast injury where hazardous live

conductors are exposed.

• Disconnect circuit power and discharge all high-voltage capacitors before

you measure resistance, continuity, or capacitance.

• Do not measure current in circuits carrying more than 600 V AC or DC 200

A with the forks.

• Never operate the Meter with the back cover removed or the case open.

• Cancer and Reproductive Harm - www.P65Warnings.ca.gov

5

Meter damage, equipment under test damage or data loss can occur if the following

guidelines are not adhered to.

• Use the proper terminals, function, and range for the measurement

application.

• Clean the case and accessories with a damp cloth and mild detergents only.

Do not use abrasives or solvents. Make sure the meter is completely dry

before use.

CAUTION

WARNING

Symbols & Descriptions

SYMBOL DESCRIPTION

Arc Flash and Shock Hazard

Shock Hazard

Warning or Caution

Choking Hazard

AC (Alternating Current)

DC (Direct Current)

Low Battery Indicator

Earth Ground

200 A Maximum Current Specification

CAT III

IEC Measurement Category III

CAT III has protection against transients in equipment in fixed-

equipment installations such as distribution panels feeders,

and short branch circuits. Also included are lighting systems in

larger buildings.

CAT IV

IEC Measurement Category IV

CAT IV has protection against transients from the primary

supply level such as a Meter or overhead or underground utility

service.

NCV

Non-Contact Voltage Sensing

NCV

Non-Contact Voltage Sensing Point

A

Amperage AC and/or DC (model dependent)

V

Voltage AC or DC

6

Symbols & Descriptions

SYMBOL DESCRIPTION

Ω

Ohms

Continuity

Capacitance

Diode

LCD Liquid Crystal Display

MAX/MIN Display MAX and MIN Measurement Values

Range Auto or Manual Range Selection

∆ ZERO

Delta (Relative)/ZERO Measurement

Double Insulation

Do not dispose of this product as unsorted municipal waste.

It must be properly disposed of in accordance with local

regulations. Please see www.epa.gov or www.erecycle.org for

additional information.

Conforms to applicable North American Safety Standards

Conforms to applicable Australian Safety Standards

Conforms to European Directives

NOTE: The Measurement Category (CAT) and voltage rating of any combination

of test probe, test probe accessory, current clamp accessory, and the Meter is the

LOWEST rating of any individual component.

7

Identification and Description of Operating

Controls and Functions for the 61-415 200A AC/

DC, 61-405 200A AC:

1. Tapered Tines (19mm Gap)

2. NCV Sensing Point

3. Hold Button

4. Function Dial

5. Main Display (LCD)

6. Volts and Resistance (V-Ω) Input Terminal

7. Common (COM) Input Terminal

8. TightSight

®

Bottom Display (61-415)

9. Protective Rubber Boot (61-415)

10. Measuring Functions

11. High Voltage, Continuity, NCV Warning LED

12. Function Select

13. Max/Min

14. Relative/Zero (ZERO 61-415 Only)

15. Backlight/Flashlight

16. Range Select

17. Tactile Barrier

18. Magnetic Hanging Strap Clip

8

Operation

9

5

1

11

4

7

10

9

8

13

12

3

6

2

14

15

16

17

18

High Voltage Warning (HI-V)

The meter LED remains RED and the beep lasts for 1 second and then goes silent

when voltages in excess of 30V are measured or when the meters voltage range is

exceeded.

NOTE: This feature does not work in the Ohm, capacitor, continuity or amperage

modes.

Data Hold Feature

Press the Hold button on the side of the meter to toggle in and out of the data

hold mode. “HOLD” appears in the lower left of the meter display when data hold

is active. Use the data hold feature to lock a measurement reading on the display.

Press the Hold button again to unlock the display and obtain a real-time reading.

MAX/MIN Feature

The MAX/MIN records the maximum or minimum measured value. Press the MAX/

MIN button to activate this feature and to toggle between MAX, and MIN readings.

The unit will continually capture MAX or MIN values over time. Depressing the

MAX/MIN button for >2 sec. exits the MAX/MIN mode.

Relative Mode

Press “ ” button to enter the Relative mode. The “ ” symbol is displayed, and

the value on the display is stored as a reference value. In the Relative mode, the

value shown on the display is always the difference between the stored reference

value and the present reading. Press the “ ” button again to exit the Relative

mode.

Zero Feature (61-415 Only)

The “ZERO” button is used to zero out the display before measuring DC current.

Press the “ZERO” button to subtract out the non-zero number. Then, measure the

DC amps. Pressing the “ZERO” button again causes the “ZERO” to flash and the

original offset number to be displayed. Press the “ZERO” button to exit this mode.

10

Operating Features

Auto Power Off (APO) Feature Disable

The meter automatically powers itself down after about 30 minutes of no use. Press

any button, and the meter will wake up and display the last reading taken before

power down. To Disable APO, press and hold the SEL button while turning the dial

to any desired function. When APO is defeated, the “APO” will be removed from the

display. Turning the meter off and back on will restore the APO default.

11

Press and hold the SEL button for > 2 seconds on the meter to turn the backlight/

flashlight on and off. The white backlight and flashlight will remain lit for about 5

minutes before they automatically turn off to conserve battery power. Or turn the

lights off by pressing the SEL for more than 2 seconds.

Backlight / Flashlight

Backlight and flashlight

are selectable to be

on in all functions.

12

Using Test Leads

WARNING: Arc Flash and Shock Hazard, Proper PPE Required.

Follow all safety procedures, wear proper PPE in accordance to NFPA 70E and

follow the guidelines below and the instructions in this manual when operating

the meter with TL-757 Test Leads or equivalent. Test Leads must be rated for the

electrical environment the meter is being used in and have a voltage rating of at

least the voltage of the circuit to be measured. Failure to comply can result in

serious injury or death.

• Choking Hazard, Small Parts. Keep Away from .....

Children. Sharp Objects Hazard, This is not a toy. It is not for use or play by

children. Keep Away from Children. Failure to do so can result in serious

injury.

WARNING:

1. Use only approved test leads. Do not use improvised connections that could

present a safety hazard.

2. Never measure AC or DC current while the test leads are inserted into the input

jacks.

3. Prior to using the test leads, inspect them carefully for damaged insulation,

exposed metal or bent probes. Check test leads for continuity. Do not use leads

if they appear damaged.

4. When using the probes, keep fingers behind the finger guards on the probes.

5. Connect the common test lead before connecting the live test lead. When

disconnecting test leads, disconnect the live test lead first.

6. Always ensure that test leads are secured so that they cannot be accidentally

snagged or tripped over.

This meter is intended for use with the IDEAL TL-757 lead set (provided with this

product) or equivalent. The lead set must comply with requirements for Overvoltage

and Measurement Categories CAT IV 600V CAT II 1000V.

Meter Operation

13

Non-Contact Voltage Sensing

First, rotate the function key to the NCV position. Place the jaw tip marked with

NCV close to an AC outlet (or any AC conductor such as light switches or power

cords) and scan back and forth across the outlet. Red indicator LED flashes at a

frequency of 3Hz, and the buzzer beeps at a frequency of 3Hz simultaneously if live

voltage is greater than 40VAC (50~60Hz) is detected. To differentiate between hot

and neutral in an outlet, place the NCV tab directly next to each slot in the outlet.

The tone (buzzer) will sound over the slot that is energized and not on the neutral

slot. Either test lead can also be used to differentiate between the hot and neutral.

Plug the red or black test lead into the V input jack on the meter. With the function

switch in the NCV position, insert the probe end of just one probe into the slots on

the outlet. The meter will beep and the Red LED will flash when a hot conductor is

contacted.

NOTES:

While the NCV is a helpful function, it is ALWAYS RECOMMENDED

that the operator verify that any electrical conductor is completely

de-energized and that no voltage is present by measuring for voltage

AND CONFIRMING THAT NO VOLTAGE IS PRESENT by using a digital

multimeter and lead set and that all applicable PPE and lock out

tag out procedures be followed before attempting any work on ANY

electrical distribution system.

Voltages with frequencies higher than 60Hz or electrostatic charges

may also be detected by the NCV sensing antenna.

Measuring AC ( ) or DC ( ) Current (Amps)

14

Measuring AC ( ) or DC ( ) Voltage

Note:

• When measuring current, align conductor with dash marks on meter jaws.

• For DC current point the arrow (located at base of jaws) towards the load.

Measuring AC ( ) or DC ( ) Current (Amps)

Measuring AC ( ) or DC ( ) Voltage

Verifying Continuity ( )

• Verify the circuit is de-energized.

• The meter will sense the level of resistance and beep if the resistance is less

than 10 Ω to confirm that continuity is present.

• Red LED will illuminate and resistance value will be displayed.

Verify the circuit is de-energized to obtain accurate measurements.

Measuring Resistance (Ohms / Ω )

15

To exit Continuity and enter

the Resistance mode,

Press the SEL Button

16

Measuring Capacitance ( )

Measuring Diodes ( )

To exit Resistance and enter

the Capacitance mode,

Press the SEL Button

To exit Capacitance and enter

the Diode Test mode,

Press the SEL Button

Measuring Capacitance ( )

Measuring Diodes ( )

Notes

17

Button Response Default Function

Operation

Note: Long Press: > 2 seconds Short Press: < 2 seconds

HOLD

HOLD: All Functions (Except

NCV)

Normal Measurement

Short Press: Circularly enter or exit the data hold mode,

LCD will display “ ”

SEL /

ACA, DCA N/A 1) Short press: Circularly select the appropriate test function.

2) When in HOLD, RANGE, MAX/MIN, REL / ZERO function, Short press the SEL key will exit

current function and go into the relative select function.

3) Long press: Circularly turn on or off the backlight and flashlight, default is off, Applicable to

all measuring settings. The backlight and flashlight will turn off automatically 5 minutes after

they are activated. Long press SEL button again to turn on the backlight and flashlight.

ACV, DCV N/A

/

Ω / /

Continuity

RANGE ACV, DCV, Ω

Auto range (LCD display

“AUTO”)

1) Short press the RANGE key to enter manual range mode (LCD will not display “AUTO”),

and the current range, press again to enter cyclical selection range. Long press: exits manual

range and enters Auto range. Switching measurement setting or restarting the unit returns

the unit to the default setting.

2) In HOLD, MAX/MIN, REL / ZERO function, Short press the RANGE key to exit the current

function and enter the relative range function.

MAX/MIN ACV, DCV, ACA, DCA, Ω Normal Measurement

1) Short press: enter “MAX/MIN” statistics mode, continuously updates the data, and you

can circularly view the maximum value→ minimum value→ maximum value. Long press:

exits statistical mode and returns to the normal working mode. After pressing the REL/ZERO,

and then short pressing MAX/MIN, the unit will show the MAX/MIN after deducting the initial

offset value.

2) When HOLD function is in use, MAX/MIN is invalid.

3) After entering the statistical mode, exit the automatic range at the same time and enter

into the current range, the APO will be disabled; exit the MAX/MIN function to restore the

automatic range and automatic shutdown.

4) In the statistical mode, a short press of the HOLD key will stop refreshing the statistical

data. At the same time, a short press of the MAX/MIN key can review the stored data of MAX/

MIN, a short press of the HOLD key exits HOLD to continue refreshing the statistical data.

/ZERO

ACV, DCV, ACA, CAP, Ω Normal Measurement

1) Short press: Circularly enter or exit REL function (when entering REL function, LCD will

display “ ” symbol )

2) Entering the REL function, exits auto range and enters into the current range.

3) Entering the REL measurement mode does not change the actual measurable range of the

current range

4) When HOLD or MAX/MIN is in use, REL function is invalid.

ZERO : DCA

(61-415)

Normal Measurement

1) Short press: Circularly enter or exits the ZERO clearing function (when entering the ZERO

function, the LCD will display the “ZERO” symbol)

2) Pressing ZERO does not affect the current automatic or manual range status. Pressing

ZERO and then pressing MAX/MIN will exit the automatic range and enter the current range.

3) When HOLD or MAX/MIN is in use, the ZERO function is invalid.

Non-Contact Voltage Indication Displays “EF” - Electromagnetic Field

Functions Operation Table

18

Button Response Default Function

Operation

Note: Long Press: > 2 seconds Short Press: < 2 seconds

HOLD

HOLD: All Functions (Except

NCV)

Normal Measurement

Short Press: Circularly enter or exit the data hold mode,

LCD will display “ ”

SEL /

ACA, DCA N/A 1) Short press: Circularly select the appropriate test function.

2) When in HOLD, RANGE, MAX/MIN, REL / ZERO function, Short press the SEL key will exit

current function and go into the relative select function.

3) Long press: Circularly turn on or off the backlight and flashlight, default is off, Applicable to

all measuring settings. The backlight and flashlight will turn off automatically 5 minutes after

they are activated. Long press SEL button again to turn on the backlight and flashlight.

ACV, DCV N/A

/

Ω / /

Continuity

RANGE ACV, DCV, Ω

Auto range (LCD display

“AUTO”)

1) Short press the RANGE key to enter manual range mode (LCD will not display “AUTO”),

and the current range, press again to enter cyclical selection range. Long press: exits manual

range and enters Auto range. Switching measurement setting or restarting the unit returns

the unit to the default setting.

2) In HOLD, MAX/MIN, REL / ZERO function, Short press the RANGE key to exit the current

function and enter the relative range function.

MAX/MIN ACV, DCV, ACA, DCA, Ω Normal Measurement

1) Short press: enter “MAX/MIN” statistics mode, continuously updates the data, and you

can circularly view the maximum value→ minimum value→ maximum value. Long press:

exits statistical mode and returns to the normal working mode. After pressing the REL/ZERO,

and then short pressing MAX/MIN, the unit will show the MAX/MIN after deducting the initial

offset value.

2) When HOLD function is in use, MAX/MIN is invalid.

3) After entering the statistical mode, exit the automatic range at the same time and enter

into the current range, the APO will be disabled; exit the MAX/MIN function to restore the

automatic range and automatic shutdown.

4) In the statistical mode, a short press of the HOLD key will stop refreshing the statistical

data. At the same time, a short press of the MAX/MIN key can review the stored data of MAX/

MIN, a short press of the HOLD key exits HOLD to continue refreshing the statistical data.

/ZERO

ACV, DCV, ACA, CAP, Ω Normal Measurement

1) Short press: Circularly enter or exit REL function (when entering REL function, LCD will

display “ ” symbol )

2) Entering the REL function, exits auto range and enters into the current range.

3) Entering the REL measurement mode does not change the actual measurable range of the

current range

4) When HOLD or MAX/MIN is in use, REL function is invalid.

ZERO : DCA

(61-415)

Normal Measurement

1) Short press: Circularly enter or exits the ZERO clearing function (when entering the ZERO

function, the LCD will display the “ZERO” symbol)

2) Pressing ZERO does not affect the current automatic or manual range status. Pressing

ZERO and then pressing MAX/MIN will exit the automatic range and enter the current range.

3) When HOLD or MAX/MIN is in use, the ZERO function is invalid.

Non-Contact Voltage Indication Displays “EF” - Electromagnetic Field

19

Function Description

Auto Range Auto detects and displays most pertinent range for measured value.

LCD Total of two LCDs (61-415 only front and bottom). Bottom LCD displays

same numbers as front display for all functions, displays a “-” symbol for

all negative readings, displays “AC” for alternating current or “DC” for

direct current and displays “Amps” for current measurement.

LCD Backlight White backlight for both front and bottom display.

Flashlight White flashlight, turns on or off with LCD blacklight simultaneously.

High Voltage

Alarm

1) Effective setting: ACV / DCV.

2) In ACV/DCV, voltage measurement value: ACV/DCV ≥30V, LCD

displays high voltage alarm lightning symbol “ ” Simultaneously the

NCV LED is on and beeping lasts for 1 second and then goes silent

during measurement.

3) In voltage measure, the voltage data is out of range and LCD display

“OL”, and high voltage alarm lightning symbol “ ” Simultaneously

the NCV LED is on and beeping lasts for 1 second and then goes

silent during measurement.

Regular Prompt 1) When turning the dial switch to any setting position except OFF, the

buzzer will beep one time and NCV LED flash one time.

2) When the button selection is valid, the buzzer will beep one time; When

the button is invalid, the buzzer will beep twice

3) About 1 minute before the automatic shutdown, the buzzer will beep 5

times continuously, and 1 long beep before the unit shuts down.

4) When the automatic shutdown function is canceled, the buzzer will

beep 5 times when it reaches the APO time setting.

Over Range

Indication

LCD displays “OL” when over range is encountered.

20

Functions Indication Table

La page charge ...

Ideal 61-405 Manuel utilisateur

Ce manuel convient également à

Ideal 61-405 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents