Amprobe AM555 Le manuel du propriétaire

AM-555-EUR

Digital Multimeter

User Manual

6/2015, 6005742 A

English

Limited Warranty and Limitation of Liability

Your Amprobe product will be free from defects in material and workmanship for one

year from the date of purchase unless local laws require otherwise. This warranty does

not cover fuses, disposable batteries or damage from accident, neglect, misuse, alteration,

contamination, or abnormal conditions of operation or handling. Resellers are not authorized

to extend any other warranty on the behalf of Amprobe. To obtain service during the

warranty period, return the product with proof of purchase to an authorized Amprobe

Service Center or to an Amprobe dealer or distributor. See Repair Section for details. THIS

WARRANTY IS YOUR ONLY REMEDY. ALL OTHER WARRANTIES - WHETHER EXPRESS, IMPLIED

OR STATUTORY - INCLUDING IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE

OR MERCHANTABILITY, ARE HEREBY DISCLAIMED. MANUFACTURER SHALL NOT BE LIABLE

FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES,

ARISING FROM ANY CAUSE OR THEORY. Since some states or countries do not allow the

exclusion or limitation of an implied warranty or of incidental or consequential damages, this

limitation of liability may not apply to you.

Repair

All Amprobe returned for warranty or non-warranty repair or for calibration should be

accompanied by the following: your name, company’s name, address, telephone number,

and proof of purchase. Additionally, please include a brief description of the problem or

the service requested and include the test leads with the meter. Non-warranty repair or

replacement charges should be remitted in the form of a check, a money order, credit card

with expiration date, or a purchase order made payable to Amprobe.

In-warranty Repairs and Replacement – All Countries

Please read the warranty statement and check your battery before requesting repair. During

the warranty period, any defective test tool can be returned to your Amprobe distributor

for an exchange for the same or like product. Please check the “Where to Buy” section on

Canada, in-warranty repair and replacement units can also be sent to an Amprobe Service

Center (see address below).

Non-warranty Repairs and Replacement – United States and Canada

Non-warranty repairs in the United States and Canada should be sent to an Amprobe Service

Center. Call Amprobe or inquire at your point of purchase for current repair and replacement

rates.

USA: Canada:

Amprobe Amprobe

Everett, WA 98203 Mississauga, ON L4Z 1X9

Tel: 877-AMPROBE (267-7623) Tel: 905-890-7600

Non-warranty Repairs and Replacement – Europe

European non-warranty units can be replaced by your Amprobe distributor for a nominal

distributors near you.

AM-555-EUR Digital Multimeter

1 Flash light

2 LC Display

3 Push buttons (See making measurement for button functions)

4 Low-impedance button

5 Rotary switch

6 SELECT button

7 Input terminal for voltage, diode, capacitance, resistance,

continuity and temperature measurement

8 COM (return) terminal for all measurements

9 Input terminal for AC/DC mA/uA measurement

10 Input terminal for AC/DC A measurement up to 20A

1

2

3

4

6

5

7

89

10

Screen Display

1 Auto- or Manual- range

2 Direct current

3 Negative reading

4 Alternate current

5 True-rms value

6 Low battery indicator

7 Data hold

8 Diode test

9 Continuity test

10 Relative zero mode

11 Non-contact Voltage

detection mode

12 Measurement units

for Resistance

13 Measurement units

for Frequency

14 Measurement units for Voltage

15 Measurement units for Current

69

5

2 4

3

7

10 19 2011 21

26

16

17

13 12

14 15

18

28

27

25

24

81 2223

16 Measurement units for Capacitance

17 Duty cycle

18 Auto power off

19 Maximum / minimum reading

memory

20 Positive / negative peak

reading memory

21 Measurement unit for temperature

22 Low-pass filter

23 400KΩ low-impedance test

24 Temperature measurement T1 or T2

25 Temperature measurement T1 - T2

26 Warning for error input terminals

connection for test leads

27 Hazardous Voltage presence

28 Analog bar graph display

1

AM-555-EUR Digital Multimeter

CONTENTS

SYMBOL .................................................................................................................2

SAFETY INFORMATION .........................................................................................2

UNPACKING AND INSPECTION .............................................................................3

FEATURES ...............................................................................................................4

MAKING MEASUREMENT .....................................................................................5

Rotary Switch Positions ....................................................................................5

Function Buttons ..............................................................................................6

Measuring AC and DC Voltage ........................................................................8

Low Pass Filter ...................................................................................................9

Measuring Frequency / Duty Cycle ...................................................................10

Measuring AC and DC Current ........................................................................12

Measuring Resistance .......................................................................................13

Measuring Continuity ......................................................................................14

Measuring Capacitance ....................................................................................15

Measuring Diode ...............................................................................................16

Measuring Temperature °C / °F ........................................................................16

Non-Contact Voltage Detection .......................................................................17

SPECIFICATIONS ....................................................................................................19

MAINTENANCE ......................................................................................................24

BATTERY AND FUSE REPLACEMENT .....................................................................25

2

SYMBOLS

Caution! Risk of electric shock.

Caution! Refer to the explanation in this manual

Alternating Current (AC)

Direct Current (DC)

The equipment is protected by double insulation or reinforced

insulation

Earth ground

Audible tone

Battery

Complies with European directives

Conforms to relevant Australian standards

Canadian Standards Association (NRTL/C)

Do not dispose of this product as unsorted municipal waste.

Contact a qualified recycler.

SAFETY INFORMATION

The meters comply with:

IEC/EN 61010-1 3rd Edition Pollution Degree 2, Measurement Category IV 600V

and Measurement Category III 1000V

IEC/EN 61010-2-030

IEC/EN 61010-031 for test leads

EMC IEC/EN 61326-1

Measurement Category IV (CAT IV) is for measurements performed at the

source of the low-voltage installation. Examples are electricity meters and

measurements on primary overcurrent protection devices and ripple control

units.

3

Measurement Category III (CAT III) is for measurements performed in the

building installation. Examples are measurements on distribution boards,

circuit- breakers, wiring, including cables, bus-bars, junction boxes, switches,

socket-outlets in the fixed installation, and equipment for industrial use

and some other equipment, for example, stationary motors with permanent

connection to the fixed installation.



WARNING: Read before using

• To avoid possible electrical shock or personal injury, follow these

instructions and use the Meter only as specified in this manual.

• Do not use the Meter or test leads if they appear damaged, or if the

Meter is not operating properly. If in doubt, have the Meter serviced.

• Always use the proper function and range for measurements.

• Before rotating the function range selection switch, disconnect test

probe from circuit under test.

• Verify the Meter’s operation by measuring on a known voltage source.

• Do not apply more than the rated voltage, as marked on the Meter, between

the test probe or between any test probe and earth ground.

• Use the Meter with caution for voltages above 30 V ac rms, 42 V ac peak,

or 60 Vdc. These voltages pose electrical shock hazards.

• Disconnect circuit power and discharge all high-voltage capacitors before

testing resistance.

• Do not use the Meter around explosive gas or vapor.

• When using the test leads, keep your fingers behind the finger guards.

UNPACKING AND INSPECTION

Your shipping carton should include:

1 AM-555-EUR Multimeter

1 Pair of test leads

2 Temperature probes

1 Temperature adaptor

1 Velcro strap

1 9V (6F22) battery (installed)

1 User manual

1 Carrying case

If any of the items are damaged or missing, return the complete package to

the place of purchase for an exchange.

4

FEATURES

The Beha-Amprobe AM-555-EUR is a fully featured multimeter designed

for professional electricians who need to maintain service or troubleshoot

advanced electrical systems. True-rms sensing accurately measures voltage on

systems affected by harmonics, built-in flashlight allows you to identify wires

while working in dark conditions, and non-contact voltage detection allows

for quick go-no-go checks without the need for an additional tool. The

AM-555-EUR also features dual input temperature measurement, a low-

impedance function to detect stray voltage, and a low pass filter to accurately

take measurements on variable frequency drives. Safety rated to CAT IV 600V

and CAT III 1000V for use in the most demanding applications.

• Measurements: AC/DC Voltage up to 1000V, ac/dc current, Resistance,

Frequency, Capacitance, Temperature, duty cycle.

• Current measurements up to 10 A, 20 A for up to 30 seconds

• Special Functions:

- Low Z - to detect “ghost” voltages

- Low pass filter for variable frequency drives

- Non-contact Voltage detection

- Audible continuity

- Diode test

• Dual reading backlight LC Display with analog bargraph

• Events:

- Data hold

- MAX / MIN memory

- Peak hold (crest)

- Relative zero mode

• Built-in flash light

• Built-in test leads storage and “third hand holder”

• Warning against improper test leads connection

• Auto and manual ranging

• Auto power off

• Low battery warning

• Velcro strap to hang a meter

• Safety: CAT IV 600V, CAT III 1000V

5

MAKING MEASUREMENT



1. Use the proper function and range for measurements.

2. To avoid possible electrical shock, personal injury or damages to the

Meter, disconnect circuit power and discharge all high-voltage capacitors

before testing resistance and diode.

3. Connecting test leads:

• Connect the common (COM) test lead to the circuit before connecting

the live lead;

• After measurement, remove live lead before removing the common

(COM) test lead from the circuit

4. Symbol “OL” is displayed on LCD when the measurement is out of range.

Rotary Switch Positions

Switch Position Measurement Function

/ AC voltage measurement / Low-pass filter (1kHz).

Use SELECT button to select alternate function.

/ NCV DC voltage measurement / Non-contact Voltage

detection.Use SELECT button to select alternate function.

/ / % DC millivolt measurement / Frequency / Duty cycle

Use SELECT button to select alternate function.

/ / Resistance / Capacitance / Continuity measurement.

Use SELECT button to select alternate function.

Voltage measurement of diode PN junction (diode test).

°C °F Temperature measurement.

Use SELECT button to select temperature unit °C or °F.

μA mA

10A

AC or DC current measurement.

Use SELECT button to select alternate function ac or dc

6

Function Buttons

Button Measurement Function

SELECT Press the yellow SELECT button to select alternate

measurement functions on the rotary switch.

RANGE /

AUTO T1-T2

Manual or auto range switching for voltage current,

resistance and capacitance. The default setting is Auto

ranging, press to switch to manual ranging. Press for 2

seconds to return to auto-ranging.

T1 or T2 or T1-T2 function switching for temperature

measurement.

REL / Relative mode / Press >2 seconds to turn ON or turn

OFF flash light.

MAX/MIN /

PEAK(1ms)

Press to enter Maximum / minimum reading memory

mode. Press again for naximum reading; press again for

minimum reading. Press > 2 seconds to exit maximum/

minimum reading mode.

Press > 2 seconds to enter Peak MAX/ Peak MIN mode.

Press again for Peak MAX reading; press again for Peak

MIN reading. Press > 2 seconds to exit Peak MAX/ Peak

MIN reading mode.

HOLD / Display freezes present reading / press > 2 seconds to turn

ON or turn OFF LCD backlight.

Low imp. 400kΩ

For voltage measurement functions only. Press and hold

the button to change the input impedance of V and COM

terminal to 400kΩ. Release 400kΩ button to return to

normal input impedance of V and COM terminal (around

10MΩ).

7

Dual Display

AC Voltage measurement

Primary display shows ac voltage.

Secondary display shows frequency.

AC Current measurement

Primary display shows ac current.

Secondary display shows frequency.

Auto Power OFF

Auto power off: Approximately 15 minutes.

When the meter is in auto power off mode, press any button to resume

normal operation.

REL Measurement (V, A, Ω and  Measurement)

The meter will calculate the values based on the stored value when set to related

mode. Display value under REL Mode = Measured Value - Reference Value

Note: Entering relative mode is not allowed when the meter displays “OL”.

Incorrect Input Terminal Connection Warning

To alert you about the incorrect connection of input terminals, the meter will

display “Warning” and buzzer will sound when test leads are falsely inserted

to terminals which are not for measurement of the selected functions.

Function selected WARNING – Incorrect Terminal Connection

V, Ω,  , , Hz, %, 10A, mA μA

mA μA °C °F 10A

10A mA μA

Hazardous Voltage Warning

LCD screen displays when the meter detects a voltage ≥30 Vac

or ≥42 V dc.

8

Measuring AC and DC Voltage

To avoid personal injury or damage to the meter, do not apply

voltage higher than 1000V ac and 1000V dc. Buzzer will sound when detect a

voltage higher than 1000V ac and 1000V dc.

Low imp. 400Ω

(For only)

9

Low Pass Filter



• To avoid personal injury or damage to the meter, do not use low pass

filter function to verify the presence of hazardous voltage in the circuit.

Always use Voltage function to verify hazardous voltages.

• Do not apply voltage higher than 1000V.

Measuring AC voltage with Low Pass Filter:

Turn rotary switch to  position and press SELECT button for Low Pass Filter

mode, symbol is displayed on screen.

Making measurement under ac voltage mode by a low pass filter can block

voltage above 1KHz. Low pass filter can be used to measure composite sine

wave signal generated by inverter and variable frequency motor drives.

Note: The meter goes into manual mode when Low Pass Filter mode is

enabled. Auto-range mode is not available for Low Pass Filter option.

10

Measuring Frequency / Duty Cycle

To avoid personal injury or damage to the meter, do not apply

voltage higher than 1000V.

1. Frequency / Duty Cycle function

Step 1: Turn the rotary switch to Hz % position. Use SELECT button for Hz

or duty cycle measurement.

Step 2: Connect test leads to the circuit. See below for connecting diagram.

(for Frequency only)

2. Measuring Frequency by using ac Voltage function

Step 1: Turn the rotary switch to  position.

Step 2: Connect test leads to the circuit. Connect the common (COM) test

lead to the circuit before connecting the live lead (connecting diagram

refer to “Measuring AC Voltage”).

Primary display shows ac Voltage measurement reading.

Secondary display shows Frequency measurement reading.

11

3. Measuring Frequency by using ac current function

Step 1: Turn the rotary switch to μA or mA or 10A position.

Step 2: Connect the test leads to the correct input 10A/mA μA current

terminal and to the circuit before powering the circuit under test

(connecting diagram refer to “Measuring AC Current”).

Primary display shows ac current measurement reading.

Secondary display shows Frequency measurement reading.

12

Measuring AC and DC Current

Press SELECT button to select ac or dc current measurement function.

To avoid personal injury or damage to the meter:

1. Do not attempt to make an in-circuit current measurement when the

open-circuit potential to earth ground exceeding 1000V

2. Switch to proper function and range for your measurement.

3. Do not place the test probe in parallel with a circuit when the test leads

are connected to the current terminals.

4. Connect the test leads to the correct input 10A/mA μA current terminal

and to the circuit before powering the circuit under test.

5. For current range from 8-10A, do not measure current for more than 20

minutes. Wait for 10 minutes before taking another measurement

6. For current range from >10-20A, do not measure current for more

than 30 seconds maximum. Wait for 10 minutes before taking another

measurement.

7. After measurement, switch OFF the circuit’s power before removing test

leads from the circuit.

13

Measuring Resistance

Disconnect circuit power and discharge all high-voltage capacitors

before testing resistance.

Note: On a higher resistance measurement (>1M), the measurement may

take a few seconds to get stable reading.

Over range or open circuit indication: OL

14

Measuring Continuity

Disconnect circuit power and discharge all high-voltage capacitors

before testing continuity.

Press SELECT button for continuity function.

15

Measuring Capacitance

Disconnect circuit power and discharge all high-voltage capacitors

before measuring capacitance. Use dc Voltage function to check the

capacitors are discharged.

Press SELECT button for capacitance measurement function.

16

Measuring Diode

Disconnect circuit power and discharge all high-voltage capacitors

before testing diode.

Note: A typical junction Voltage drops 0.5 V to 0.8 V.

Measuring Temperature °C / °F



1. To avoid personal injury or damage to the meter, do not apply the

temperature probe to any live conductive parts.

2. Temperature sensor K-type (nickel-chromium/nichrosi) thermocouple is

suitable for temperature measurement below 230°C (446°F).

Measurement steps:

Step 1: Turn the rotary switch to °C/°F position. The display will show

“OPEN”. Press SELECT button for conversion to °F measurement.

Step 2: Connect the temperature probe (K-type) to the Meter and to the

surface to be measured. Two temperature surface points can be measured

at the same time by using the provided temperature probes.

Step 3: Press RANGE button to select temperature measurement T2 or T1-T2

(the default temperature measurement is T1).

La page charge ...

Amprobe AM555 Le manuel du propriétaire

Amprobe AM555 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents