Lawnmaster GT1018S Manuel utilisateur

Marque: Lawnmaster

Modèle: GT1018S

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

10" Single Line Bump Feed Grass Trimmer GT1018S

Coupe-Gazon Ligne Simple 10 Po À Avancement Par

Choc GT1018S

Read all safety rules and instructions carefully before operating this tool.

Distributed By Cleva North America 601 Regent Park Court Greenville, SC 29607 (866)-384-8432

Lisez attentivement l’ensemble des règles de sécurité et les instructions avant d’utiliser cet appareil.

Distribué par Cleva North America 601 Regent Park Court Greenville, SC 29607 (866)-384-8432

MNL_GT1018S_V1

EN p. 2

FR p. 20

Operators Manual / Mode D’emploi

3084514

Conforms to UL STD 82

Certified to CAN/CSA STD.

C22.2 No. 147-M90

Contents.......................................................................................................................................2

Product Specifications.. ..........................................................................................................2

General Safety Rules.............................................................................................................3-4

Electrical Information.....................................................................................................5-7

Symbols................................................................................................................................... 8

Know Your Grass trimmer............................................................................................... 9

Assembly

................................................................................................................................10

Operation.......................................................................................................................... 11-15

Troubleshooting..........................................................................................................................15

Exploded View ...................................................................................................................

....16

Parts List ............................................................................................................................... 17

Warranty .....................................................................................................................................18

Notes........................................................................................................................................... 19

CONTENTS

PRODUCT SPECIFICATIONS

10” GRASS TRIMMER

No-load Speed .....................................................................................................11000 RPM

Amp.........................................................................................................................

2.5 A

Voltage

............................................................................................................

120 V~60Hz

Cutting Swath........................................................................................................................ 10"

Feed Type - Bump Line.................................................................................. Single Line 0.065"

Weight .........................................................................................................2.65 lbs (1.2 Kg )

GENERAL SAFETY RULES

When using the machine the safety rules must be followed. For your own safety and bystanders please

read these instructions before operating the machine. Do not use the machine without reading the instruction

sheet. Please keep the instructions safe for later use.

• This grass trimmer is designed for cutting grass and similar soft vegetation and for trimming grass

edges in private and hobby garden areas which are not accessible with a grass trimmer.

• The device is not allowed to be used in public gardens, parks, sports centers or at roadsides as

well as in agriculture and forestry.

•

This grass trimmer is not allowed to be used for cutting or chopping, otherwise, there is a risk of injury.

- Hedges, shrubs and bushes,

- Flowers,

- In terms of composting.

• This grass trimmer is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the grass trimmer by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the grass trimmer.

•

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly

qualified persons in order to avoid a hazard.

• Wear protective glasses or goggles.

• Never allow children or people unfamiliar with the instructions to use the grass trimmer.

• Stop using the grass trimmer while people, especially children, or pets are nearby.

• Only use the grass trimmer in daylight or good artificial light.

•

Before using the grass trimmer and after any impact, check for signs of wear or damage and repair

as necessary.

• Never operate the grass trimmer with damaged guards or without the guards in place.

• Keep hands and feet away from the cutting means at all times and especially when switching on

the motor.

• always return the machine to its normal operating position before switching on.

• Never fit metal cutting elements

• Never use replacement parts or accessories not provided or recommended by the manufacturer

• Disconnect the grass trimmer from the mains before checking, cleaning or working on the grass

trimmer and when it is not in use.

• Always ensure that ventilation openings are kept clear of debris.

WARNING

GENERAL SAFETY RULES

ADDITIONAL SAFETY INSTRUCTIONS FOR YOUR GRASS TRIMMER

• Do not expose to moisture.

• Use only on AC mains supply voltage shown on the product rating label.

• Avoid operating your trimmer in wet grass, where feasible.

• Take care in wet grass, you may lose your footing.

• On slopes, be extra careful of your footing and wear nonslip footwear.

• Do not walk backwards when trimming, you could trip. Walk never run.

• Switch off before pushing the trimmer over surfaces other than grass.

• Never pick up or carry a trimmer by the cord.

• Do not lean over the trimmer guard objects may be throw by the rotating TrimFast blades.

• Keep all nuts, bolts and screws tight to be sure the trimmer is in safe working condition.

• To avoid the risk of injury keep fingers and hands clear of therotating TrimFast blades on the

leading edge of the guard.

MAINTENANCE

• After use, disconnect the grass trimmer. from the power source and check for damage

• When not in use store the grass trimmer. out of the reach of children

• Electrical powered trimmers should only be repaired by an authorised repairer

• Use only manufacturers recommended replacement parts and accessories. The preparation for

use, operation and maintenance of the grass trimmer:

- Read the instructions carefully;

- Be familiar with the controls and proper use of the grass trimmer.

- Before use check the supply and extension cord for signs of damage or ageing,

- If the cord becomes damaged during use, disconnect the cord from the power supply immediately.

DO NOT TOUCH THE CORD BEFORE DISCONNECTING THE SUPPLY;

- Do not use the lawn trimmer (edge trimmer), if the cords are damaged or worn.

W A R N I N G

- Cutting elements continue to rotate after the motor is switched off;

- Keep extension cords away from cutting elements;

- It is recommended that grass trimmers should be supplied via a residual current device (RCD) with

a tripping current of not more than 30mA.

WARNING

ELECTRICAL INFORMATION

DOUBLE INSULATED

TO AVOID ELECTRICAL HAZARDS, FIRE HAZARDS, OR DAMAGE TO THE TOOL, USE PROPER

CIRCUIT PROTECTION. YOUR GRASS TRIMMER IS WIRED AT THE FACTROY FOR 120 V

OPERATION. CONNECT TO A 120 V, 15 A CIRCUIT, AND USE A 15 A TIME-DELAYED FUSE OR

CIRCUIT BIREAKER. TO AVOID SHOCK OR FIRE, IF THE EXTENSION CORD IS WORN, CUT OR

DAMAGED IN ANY WAY, REPLACE IT IMMEDIATELY.

This grass trimmer has a plug that looks like the one shown in Fig. 1

The grass trimmer is double insulated to provide a double thickness of insulation between you and

the tool’s electrical system. All exposed metal parts are isolated from the internal metal motor

components with protective insulation.

USE ONLY IDENTIFICAL REPLACEMENT PARTS WHEN SERVICING THE GRASS TRIMMER,

TO AVOID INJURY.

WARNING

DOUBLE INSULATION DOES NOT TAKE THE PLACE OF NORMAL SAFETY PRECAUTIONS

WHEN OPERATING THIS GRASS TRIMMER

WARNING

TO AVOID ELECTROCUTION:

1. Use only identical replacement parts when servicing a tool with double insulation.

Servicing should be performed by a qualified technician.

2. Do not use in wet or damp areas or expose to rain.

Fig. 1

CAUTION

ALWAYS MAKE SURE THAT YOUR OUTLET IS PROPERLY GROUNDED. IF UNCERTAIN,

HAVE IT CHECKED BY A CERTIFIED ELECTRICIAN.

WARNING

THIS GRASS TRIMMER IS FOR OUTDOOR USE ONLY. DO NOT EXPOSE TO RAIN OR USE IN

DAMP LOCATIONS.

ELECTRICAL INFORMATION

GUIDELINES FOR USING EXTENSION CORDS

USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition.

When using an extension cord, be sure to use one heavy enough to carry the current your product

will draw. An undersized cord will cause overheating. The table below shows the correct size to use

depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge.

The smaller the gauge number, the heavier the cord.

GROUNDING INSTRUCTIONS

IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides the path of least

resistance for electric current, and reduces the risk of electric shock. This tool is equipped with

a POLARIZED plug. The plug MUST be plugged into a matching grounded extension cord in

accordance with All local codes and ordinances.

DO NOT MODIFY THE PLUG PROVIDED. If it will not fit the properly grounded extension cord,

have the proper outlet installed by a qualified electrician.

Minimum Gauge for Extension Cords (AWG)

(when using 120 V only)

Ampere Rating

More Than

Not More Than

25’ (7.6 m)

50’ (15 m)

100’ (30.4 m)

Not Recommended

150’ (45.7 m)

Total Length of Cord in Feet (meters)

WARNING

ALTHOUGH THIS GRASS TRIMMER IS DOUBLE INSULATED, THE EXTENSION CORD AND

RECEPTACLE MUST STILL BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR

FROM ELECTRICAL SHOCK.

ELECTRICAL INFORMATION

Make sure your extension cord is properly wired and in good electrical condition. Always replace a

damaged extension cord or have it repaired by a qualified person before ues. Keep extension cords

away from sharp objects, excessive heat and damp or wet areas.

Use a separate electrical circuit for your tools. This circuit should comprise a wire of at least 12

gauge and should be protected with a 15 A time-delayed fuse. Before connecting the motor to the

power line, make sure the switch is in the OFF position and the electric current is identical to that

stamped on the motor nameplate. Running at a lower voltage will damage the motor.

SYMBOL NAME DESIGNATION/EXPLANATION

V Volts Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watts Power

min Minutes Time

Alternating Current Type of current

Direct Current Type or a characteristic of current

Class II Construction Double-insulated construction

No Load Speed Rational speed, at no load

/min

Per Minute

Revolutions, strokes, surface speed, orbits etc.,

per minute

Wet Conditions Alert Do not expose to rain or use in damp locations

Read The Operator’s Manual

To reduce the risk of injury user must read and

understand operator’s manual before using this

product.

Eye Protection

Wear eye protection when operating

this equipment.

Safety Alert Precautions that involve your safety.

Long Hair

Failure to keep long hair away from the air inlet

could result in personal injury.

Loose

Clothing

Failure to keep loose clothing from being drawn

into air intake could result in personal injury.

Keep Bystanders Away Keep all bystanders at least 50 ft. away.

Some of the following symbols may be used on this product. Please study them and learn their

meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.

SYMBOLS

KNOW YOUR GRASS TRIMMER

Know Your Grass Trimmer (Fig. 2)

The safe use of this product requires an understanding of the information on the product and in

this operator’s manual as well as a knowledge of the project you are attempting. Before use of

this product, familiarize yourself with all operating features and safety rules.

Flower Guard

Motor Housing

Pommel handle

ON/OFF switch

Upper handle

Trimming Line

Safety Guard

Built-In Cord Retainer

Additional Spool Storage

(additional spool not included)

Fig. 2

ASSEMBLY

Functional description

This portable hand held grass trimmer is powered by an electrical motor.

This trimmer features a single line bump feed head that is used for safe and efficient grass

cutting.

After the safety guard is installed it will protect the user during trimming operations.

The following describes the functions of the operating parts.

Extent of the delivery

Carefully unpack the trimmer and check that it is complete:

• Lawn trimmer (2 sections)

• Safety guard with 2 installation screws included.

• Flower guard

WARNING

Always disconnect from power source before working on the trimmer. Wait until motor has completely

stopped before attempting any maintenance. There is danger of electric

shock and the possibility

of injury by the rotating trimmer line unless motor has stopped rotating.

Assembling instructions

NOTE: Once the lower and upper sections of the trimmer has been assembled,

they can not be seperated.

Assembling the guard( Fig.

3-4

)

1. Assemble the housing and handle.

2. Align the safety guard with the holes on the underneath side of the motor housing and slide

into position.

3. Attach the guard with the two screws Assembling the equipment.

4. Connect the upper housing and the lower housing.

The safety guard and handle must be in the same direction. Be careful that the internal power

cord is not tight or twisted.

Fig. 3 Fig. 4

OPERATION

Switching ON and OFF ( Fig. 5 )

1. Form a loop in the end of the extension cable, conduct it through the opening in the upper

handle (2) and hang it on to the strain relief (3).

2. Connect the trimmer to the mains socket.

3. Ensure a secure stance and hold on to the trimmer with two hand. Do not deposit the cutting

head on the ground.

4. To switch on depress the ON/ OFF switch (1). Release the switch to switch off.

WARNING

Danger of injury!

Never use the trimmer without its safety guard. Always check the operability of the trimmer before it

is used. Check that the mains voltage is the same as indicated on the rating plate. Always wear

goggles when working with the trimmer.

NOTE:

Once the lower and upper sections of the trimmer has been assembled, they can not

be seperated.

After the trimmer has been switched off the cutting head will continue to rotate for a few

seconds. Keep hands and feet well away.

The ON / OFF switch must not be locked in place. The trimmer must not be used if the

switch is damaged. There is the immediate danger of injury if the motor does not switch

off after the ON /OFF switch has been released.

NOTE:

Always remove grass residue from cutter so that the cutting effect is not impaired.

Fig. 5

WARNING

①

②

③

OPERATION

Cutting device - advancing the trimmer line (Figs. 6)

In order to advance a length of trimmer line, firmly tap the bump cap on the lawn while the trimmer

is running. This will automatically advance a new length of trimmer line and trim the line to the

correct length. A firm but gentle motion should be used when tapping the bump cap on the lawn.

This advancing process may be repeated as often as necessary. Never try to advance the line on

a hard surface such as a sidewalk or driveway. If unit fails to advance, unplug power from trimmer

and clean the bump cap both inside and out.

Flower Guard

Pull the flower guard out of the trimmer head (Fig.7). If the flower guard is no longer required, it can be

pushed in again (park position).

Using the flower guard

The grass trimmer is equipped with a flower guard that can be lowered to push flowers away from

the cutting line so they are protected (Fig.8). The flower guard is an indicator of the maximum

cutting range of the line.

Fig. 7

Fig. 8

Fig. 6

Trimming

1. Hold the tool as shown. what figure are you referencing.(Fig.9)

2. Gently swing the trimmer from side to side .(Fig. 10)

3. When cutting long grass, work in stages from the top. Take small cuts. Keep the tool away from

hard objects and delicate plants.

4. If the tool starts running slowly, reduce the load.

• Do not cut moist or wet grass.

• Before starting the trimmer check that the cutting head will not come into contact with stones,

rubble or other foreign bodies.

• Switch on the trimmer before you approach the grass that is to be cut.

• Always trail the extension cord behind you. Do not pass the operating trimmer over the extension

cord as the cord could be damaged.

• Do not overload the trimmer during operation.

• Avoid contact with obstacles (stones, walls, fences, etc.) as this will rapidly wear out the trimmer line.

• Do not hit the cutting head on the ground during operation.

• Ensure that the cutting head has stopped before you deposit the equipment on the ground. Cut

the grass by swaying the trimmer sideways to the right and left. Cut slowly, keeping the grass

trimmer inclined forward slightly when cutting. Cut tall grass by a series of levels from top to bottom.

OPERATION

Fig. 9 Fig. 10

WARNING

Danger of injury!

WARNING Never attempt to lock the trigger lever in the on position.

• Carefully clean the trimmer and its accessories after each use (see “Cleaning and maintenance”), thereby

avoiding mold formation.

• Store the trimmer in a dry place well out of reach of children.

• Do not expose the trimmer for extended periods to direct sunlight.

• Do not wrap plastic bags around the trimmer as this could result in the formation of moisture and mould.

• Do not stand the trimmer on its protective guard. Suspend it by its upper handle in such a manner that the

protective guard does not come into contact with other objects. This is because the protective guard could

become deformed, thereby changing its dimensions and its safety properties.

Any work that is not described in these Instructions must be carried out by a servicing

agency authorized by us. Only use original parts and be very careful with the line cutter

during installation work. Danger of injury!

Disconnect the plug from the power source after every use and check the grass trimmer for damaged parts.

Cleaning and maintenance

Always disconnect the plug from the power source before working on the trimmer.

Storage

OPERATION

Cleaning

Do not jet water onto the trimmer and do not clean it under flowing water. This would

result in the danger of an electric shock and the trimmer could be damaged. Always

keep the trimmer clean. Do no use cleaning agents and solvents.

• After the work has been completed remove all grass and soil from the cutting device and the protective

guard.

• Ensure that the ventilation slots are always clean and free of grass.

• Clean the trimmer with a soft brush or a cloth.

WARNING

NOTE: Dispose of the trimmer, its accessories and the packaging in an environment friendly manner.

Electrical grass trimmers must not be disposed of with the domestic waste Hand in a redundant trimmer to

a recycling centre. The plastic and metals can then be sorted out and graded for recycling.

Our Service Centre will be happy to answer any questions in this respect. Defective units returned to us will

be disposed of for free.

Disposal And Protection Of The Environment

Replacing Trimmer Spool - part # RS0202

To replace trimmer spool - using index finger and thumb firmly squeeze the two serrated tabs found on

trimmer spool head as shown. Enough pressure will release the spool cover exposing the trimmer spool.

Remover the spool cover and remove the empty spool.

At this time the spool can either be re-filled using 0.065” trimmer line or a replcement spool (part #RS0202)

can be installed. To install new spool, simply place

new spool in spool head knob side facing up and

feed the loose end of the trimmer line through the

round steel eyelet on spool head. The line should

be free. Align the spool cover and snap into place.

Follow the advancing line procedures in earlier

section of this manual.

OPERATION

TROUBLE SHOOTING

Problem

Product does not reach

full power

Trimmer Does Not Start

Unsatisfactory result

Air vents are blocked

No Main Power

Trimming line worn

Advance additional line OR

Replace with new trimmer spool

On/off Switch Defective

Worn Carbon Brushes

Motor line

Check Power Cord and Plug

Repair By After-sales Service

Advance additional line OR

Replace spool with new trimmer line

Use a proper extension cord

Connect to another power source

Clean the air vents

Extension cord not suitable

for operation with this product

Power source (e.g. generator)

has too low voltage

Possible Cause Remedy

EXPLODED VIEW

ITEM NO. PART NO. DESCRIPTION

PART LIST

QTY

8.1

8.2

TODXD1.43.UL.X1.01

TOQTGX.01.YX.X1.02

GT21FM.10.03.X1.01

GT27FM.30.00

TOTHYL.01.09

GT27FM.40.00

GT21FM.00.04.02

TM5863.00.00.X1.01

GT21FM.20.01.W2.00

GT21FM.00.03

TOTHYY.04.12

GT21FM.00.01.X1.01

GT22FM.10.01.X1.01

Power Lead

Power Lead Retainer

On/off Button

Spool (RS0202)

Spring

Debris Guard W/ Screws

Flower Guard

Motor Assembly

Spool Head

Spool Cover

Spring

Lower Motor Housing

Upper Housing

WARRANTY

We take pride in producing a high quality, durable product. This Lawnmaster® product carries a

limited two (2) year warranty against defects in workmanship and materials from date of purchase

under normal household use. If product is to be used for commercial, industrial or rental use, a 30

day limited warranty will apply. Batteries carry a one-year warranty against defects in workmanship

and materials. Batteries must be charged in accordance with the operator's manuals directions and

regulations in order to be valid. Warranty does not apply to defects due to direct or indirect abuse,

negligence, misuse, accidents, repairs or alterations and lack of maintenance. Please keep your

receipt/packing list as proof of purchase. This warranty gives you specific legal rights, and you

may have other rights, which vary from state to state. For product service call Customer Service at

(866) 384-8432.

Items not covered by warranty :

1. Any part that has become inoperative due to misuse, commercial use, abuse, neglect, accident,

improper maintenance, or alteration; or

2. The unit, if it has not been operated and/or maintained in accordance with the owner's manual;

3. Normal wear, except as noted below;

4. Routine maintenance items such as lubricants, blade sharpening;

5. Normal deterioration of the exterior finish due to use or exposure.

Transportation Charges : Transportation charges for the movement of any power equipment unit or

attachment are the responsibility of the purchaser. It is the purchaser’s responsibility to pay

transportation charges for any part submitted for replacement under this warranty unless such

return is requested in writing by LawnMaster.

SAVE YOUR RECEIPTS. THIS WARRANTY IS VOID WITHOUT THEM.

NOTES

Sommaire..................................................................................................................................20

Caractéristiques Du Produit.. .................................................................................................20

Règles De Sécurité Générales........................................................................................21-23

Informations Électriques ......................................................................................... 23-26

Symboles.............................................................................................................................. 27

Apprenez À Connaître Votre Coupe-gazon....................................................................28

Montage

................................................................................................................................29

Fonctionnement ....................................................................................................................30

Dépannage .............................................................................................................................31-34

Vue Éclatée ................................................................................................................

.........35

Liste Des Pièces .............................................................................................................. 36-37

Garantie ....................................................................................................................................

Notes......................................................................................................................................... 39

SOMMAIRE

CARACTÉRISTIQUES DU PRODUIT

Coupe-Gazon Ligne Simple 10 Po À Avancement Par Choc GT1018S

Vitesse À Vide .....................................................................................................11000 RPM

Amp.......................................................................................................................

2.5 A

Tension

..........................................................................................................

120 V~60Hz

Trajectoire De Coupe..................................................................................................... 250mm

Type D’alimentation – Avancement Par Choc ....................................... Ligne Simple 0,065 Po

Poids .......................................................................................................... 2.65 lbs (1.2 Kg )

La page charge ...

Lawnmaster GT1018S Manuel utilisateur

Marque: Lawnmaster

Modèle: GT1018S

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Lawnmaster GT1018S User manual

Lawnmaster GT1018S Manuel utilisateur

Lawnmaster GT1018S Manuel utilisateur

dans d''autres langues

Autres documents