Dustbane Hurricane 400 XTT Traction Operations Manual
- Catégorie
- Scrubber
- Taper
- Operations Manual
Ce manuel convient également à
Operations Manual
Manuel d’opérations
Hurricane 400 / Hurricane 400-TR
Auto-Scrubber / Auto-récureuse
19319 / 19319-TR
Date of Issue / Date d’émission : 2020-04
Serial Number / Numéro de série : Date of Purchase / Date d’achat :
Distributor Name / Nom du distributeur :
3Operations Manual Hurricane 400 XTT / Hurricane 400 XTT – Traction
GENERAL INFORMATION
Purpose of this manual
This manual has been written by the Manufacturer and is an integral part of the machine
1
.
It denes the purpose for which the machine has been designed and constructed and contains all the information required
by operators
2
.
In addition to this manual, which contains information for operators, other publications are available providing specic
information for maintenance personnel
3
.
The terms “right” and “left”, “clockwise” and “counter-clockwise” refer to the forward movement of the machine.
Constant compliance with the instructions provided in this manual guarantees the safety of the operator and the machine,
ensures low running costs and high quality results and extends the working life of the machine. Failure to follow these
instructions may lead to injury to the operator or damage to the machine, oor and environment.
To nd the topic that interests you more rapidly, consult the list of contents at the beginning of the manual.
Parts of the text requiring special attention are printed in bold and preceded by the symbols illustrated and described here.
! DANGER: Indicates the need for attention in order to avoid a series of consequences which could cause death or serious injury
to personnel.
! WARNING: Indicates the need for attention in order to avoid a series of consequences which could cause damage to the machine
or work environment or nancial loss.
! INFORMATION: Very important instructions. In line with the company’s policy of constant product development and updating,
the Manufacturer reserves the right to make modications without prior notice. Although your machine may dier appreciably from
the illustrations in this document, the correctness and validity of the instructions contained in this manual are guaranteed.
Documentation provided with the machine
• Parts Manual
• Operations Manual
• Quick Guide
• Warranty Information
1. The denition “machine” replaces the trade name covered by this manual.
2. Persons responsible for using the machine without performing any operations requiring precise technical skills.
3. Persons with experience, technical training and a knowledge of legislation and standards, able to perform all the necessary
operations and to recognize and avoid possible risks in handling, installation, use and maintenance of this machine.
4 Operations Manual Hurricane 400 XTT / Hurricane 400 XTT – Traction
TECHNICAL INFORMATION
General description
This machine is a scrubber dryer for washing and drying at, horizontal, smooth or moderately rough, even and obstacle free
oors in civil and industrial premises.
The scrubber dryer spreads a solution of water and detergent in the correct concentration on the oor and then scrubs it to
remove the dirt. By carefully choosing the detergent and brushes (or abrasive disks) from the wide range of accessories available,
the machine can be adapted to a wide range of combinations of types of oor and dirt.
A suction system incorporated in the machine dries the oor after washing by means of the low pressure generated in the dirty
water tank by the suction motor. The squeegee connected to the tank collects the dirty water.
The machine is moved forward by:
Non-Traction drive: the auto-scrubber is provided with a special mechanical drive device which exploits
the friction between the brush and the oor to generate a forward movement (for further details, see paragraph 6.7).
Traction drive: the auto-scrubber is moved forward by means of a special electromechanical drive device.
Legend
Fig./Abb.
图
1
Fig./Abb./
图
2
Fig./Abb./
图
3
Fig./Abb./
图
4 Fig./Abb./
图
5
The main parts of the machine are as follows:
• Control panel
• Recovery tank – collects the dirty water picked up from the oor after washing [Ref. 2]
• Head lift pedal – raises the brush head during transport [Ref. 3]
• Head assembly – holds the brushes / pads [Ref. 4]
• Brushes / pads – distribute the chemical solution on the oor and removes the dirt [Ref. 5]
• Squeegee assembly – wipes and dries the oor by collecting the water [Ref. 6]
• Solution tank – contains and transports the mixture of clean water and chemical solution [Ref. 7]
5Operations Manual Hurricane 400 XTT / Hurricane 400 XTT – Traction
Hazard Areas
Tank assembly: when using certain detergents, danger of irritation for eyes, skin, mucous membranes
and respiratory tract and of asphyxia. Danger represented by the dirt collected from the environment (germs and chemical
substances). Danger of crushing between the two tanks when the recovery tank
is replaced on the solution tank.
Control panel: danger of short circuit.
Bottom of washing head: danger due to brush rotation.
Rear wheels: danger of crushing between the wheel and chassis.
Battery compartment (in the solution tank): danger of short circuit between the battery poles
and presence of hydrogen during charging.
SAFETY INFORMATION
Safety precautions
Read the “User Manual” carefully before start-up and use or before performing maintenance or any other work on the machine.
! WARNING: Rigorously follow all the instructions in this Manual (in particular those marked “Danger!” and “Warning!”). Also respect
the labels applied to the machine. The Manufacturer declines all liability for injury to persons or damage to property resulting from failure
to follow instructions.
• The auto-scrubber must be used exclusively by persons trained in its use and/or who have demonstrated their ability and
have been expressly instructed to use the auto scrubber.
• The machine must not be used by minors.
• The machine must not be used for purposes other than those for which it was expressly designed. Scrupulously respect
all safety standards and conditions applicable to the type of building in which the machine is to be operated (e.g.:
pharmaceutical companies, hospitals, chemicals, etc).
• Do not use the machine in places with inadequate lighting or explosive atmospheres, on public roads, in the presence of
dirt hazardous to health (dust, gas, etc) and in unsuitable environments.
• The machine is designed for temperatures of between +4°C and +35°C when in use and between +0°C and +50°C when
not in use.
• The machine is designed to work in a humidity of between 30% and 95%.
• Never use or pick up ammable liquids or explosives (e.g. petrol, fuel oil, etc), ammable gases, dry dusts, acids and
solvents (e.g. paint solvents, acetone etc) even if diluted.
• Never pick up aming or incandescent objects.
• Never use the machine on slopes or ramps of more than 2%. In the case of slight slopes, do not use the machine
transversally, always maneuver with care and do not reverse.
• When transporting the machine on steeper ramps or slopes, take the utmost care to avoid tipping up and/or
uncontrolled acceleration. Move the machine on ramps and/or steps only with the brush head and squeegee raised.
• Never park the machine on a slope.
• The machine must never be left unattended with the motor or engine on. Before leaving it, turn
the motor or engine o, make sure it cannot move accidentally.
• Always pay attention to other people, children in particular, present in the place where you are working.
• Never use the machine to transport people or things or to tow things. Do not tow the machine.
• Never rest objects of any weight on the machine for any reason.
• Never obstruct ventilation and heat dispersion slits.
• Never remove, modify or circumvent safety devices.
6 Operations Manual Hurricane 400 XTT / Hurricane 400 XTT – Traction
• Numerous unpleasant experiences have shown that a wide range of personal objects may cause serious accidents. Before
beginning work, remove jewelry, watches, ties, etc.
• The operator must always use personal protection devices - protective apron or overalls, non-slip waterproof shoes,
rubber gloves, protective goggles and ear protectors and mask to protect the respiratory tract.
• Keep hands away from moving parts.
• Never use detergents other than those specied. Follow the instructions on the MSDS if you come into contact.
• Make sure the power sockets used for the models with battery charger are connected to a suitable grounding system and
protected by dierential thermal solenoid switches.
• Make sure the electrical characteristics of the machine (voltage, frequency, absorbed power) given
on the rating plate (g. 1) are the same as those of the main electricity supply. The machine with cable has a three-wire
cable and a three pin grounded plug for use in an appropriate grounded socket. The ground wire is yellow and green.
Never connect this wire to anything other than
the ground contact of the socket.
• It is crucial to respect the battery manufacturer’s instructions and current legislation.
The batteries should always be kept clean and dry to avoid surface leakage current. Protect
the batteries from impurities such as metal dust.
• Never rest tools on the batteries as this could cause short circuit and explosion.
• When using battery acid, always follow the relative safety instructions scrupulously.
• In the presence of particularly strong magnetic elds, assess the possible eect on the control electronics.
• Never wash the machine with water jets.
• The uids collected contain detergent, disinfectant, water and organic and inorganic material.
They must be disposed o in accordance with local legislation.
• In the case of malfunction and/or faulty operation, turn the machine o immediately (disconnecting it from the main
power supply or batteries) and do not tamper. Contact a service center authorized by the Manufacturer.
• All maintenance operations must be performed in an adequately lit place and only after disconnecting the machine from
the power supply.
• All work on the electrical system and all maintenance and repair operations other than those explicitly described in this
manual must be performed by specialized personnel expert in the sector only.
• If the power cable, plug or terminals require replacing, make sure the electrical connections and cable grip inside the
control panel are tightly fastened to guarantee the resistance of the cable if pulled. Then replace the panel carefully to
guarantee the safety of the operator.
• Only original accessories and spare parts supplied by the Manufacturer may be used in order to guarantee safe problem-
free operation of the machine. Never use parts removed from other machines or from other kits.
• This machine has been designed and constructed to provide ten years’ service from the fabrication date shown on the
rating plate (g. 1). After this time, whether the machine has been used or not,
it should be disposed of according to current legislation in the country in which it is used:
• At the end of the machine’s life, please dispose according to local regulations.
The machine is designed and constructed to provide ten years’ service from the date of manufacture shown on the nameplate.
After this period, whether the machine has been used or not, it should be disposed of according to current legislation in the
country in which it is used.
It should be disconnected from the power supply, emptied of all liquids and cleaned prior to disposal.
The machine is classied as WEEE-type special waste and is covered by the requirements of applicable environmental protection
regulations (2002/96/EC WEEE).
The machine must be disposed of separately from ordinary waste in compliance with current legislation and standards.
Also make sure that all parts of the machine that could represent a hazard, particularly to children, are made safe.
Alternatively, return the machine to the Manufacturer for a complete overhaul.
7Operations Manual Hurricane 400 XTT / Hurricane 400 XTT – Traction
MOVEMENT AND INSTALLATION
Lifting and transporting the packaged machine
! WARNING: During all lifting operations, make sure the packaged machine is rmly secured to avoid it tipping up or being accidentally
dropped. Always load/unload lorries in adequately illuminated areas.
The machine is packaged on a wooden pallet by the Manufacturer. It must be loaded onto the transporting vehicle using suitable
equipment (see EC Directive 2006/42 and subsequent amendments and/or additions). At destination, it must be unloaded using
similar means.
A fork lift truck must always be used to lift the packaged body of the machine. Handle with care to avoid knocking or overturning
the machine.
Delivery checks
When the carrier delivers the machine, make sure the packaging and machine are both whole and undamaged. If the machine
is damaged, make sure the carrier is aware of the damage and before accepting the goods, reserve the right (in writing) to request
compensation for the damage.
Unpacking:
! WARNING: When unpacking the machine, the operator must be provided with the necessary personal protection devices (gloves,
goggles, etc.) to limit the risk of accident.
Proceed as follows to unpack the machine:
• Cut and remove the plastic straps;
• Remove the cardboard;
• Remove the bags in the battery compartment (in the detergent tank) and check the contents:
• product literature;
• battery bridges with terminals;
• 1 battery charger connector ;
• Depending on the model, remove the metal brackets or cut the plastic straps xing the machine chassis to the pallet;
• Using a sloping ramp, push the machine backwards o the pallet;
• Unpack the brushes from their packaging.
• Clean the outside of the machine, taking care to respect safety regulations.
Once the machine is clear of the packaging, proceed to install the batteries (see the “Batteries: installation and connection”
section).
The packaging may be kept as it can be reused to protect the machine if it is moved to another site or to a repair workshop.
Otherwise it must be disposed of in compliance with current legislation.
8 Operations Manual Hurricane 400 XTT / Hurricane 400 XTT – Traction
Batteries: preparation
! DANGER: During battery installation and any type of battery maintenance, the operator must be provided with the necessary personal
protection devices (gloves, goggles overalls, etc.) to limit the risk of injury. Keep clear of naked ames, avoid short circuiting the battery
poles, avoid sparks and do not smoke.
Batteries (WET) are normally supplied lled with acid and ready for use.
If the batteries are wet, proceed as follows before installing them in the machine:
• Remove the caps and ll all elements with sulfuric acid solution specic for batteries until the plates are entirely covered
(this requires at least a couple of rells for each element). IF IN DOUBT, CONTACT THE DEALER.
• Leave the batteries stand for 4-5 hours to allow air bubbles to come to the surface and the plates to absorb the
electrolyte.
• Make sure the level of electrolyte is still above the plates and if necessary top up with sulfuric acid solution.
• Close the caps.
• Install the batteries in the machine (following the procedure described below).
• Charge the batteries before starting up the machine for the rst time. Follow the instructions in the “Battery maintenance
and charging” section.
Batteries: installation and connection
! INFORMATION: Batteries must only be installed and connected by qualied technical personnel.
! DANGER: Remove the electronic key from the instrument panel before installing and connecting the batteries. Make sure you connect
the terminals marked with a “+” to the positive poles of the battery. Do not check the battery charge by sparking.
Meticulously follow the instructions given below as short circuiting the batteries could cause them to explode.
• Make sure the two tanks are empty (if necessary, empty them. See the relevant paragraph).
• Release the recovery tank (ref. 1) from the solution tank by pulling the catch. Tilt the recovery tank all the way back to
provide access to the battery compartment.
• Place the batteries in the compartment in the direction shown in the drawing printed inside
the compartment on the solution tank.
• Referring to the wiring layout, connect the battery cable and bridge terminals to the battery poles. Arrange the cables as
shown in the diagram, tighten the terminals on the poles and cover with Vaseline.
• Lower the recovery tank. Make sure it latches properly with the solution tank;
! WARNING: Never allow the batteries to become excessively at as this could damage them irreparably.
Fig./Abb.
图
1
Fig./Abb./
图
2
Fig./Abb./
图
3
Fig./Abb./
图
4 Fig./Abb./
图
5
9Operations Manual Hurricane 400 XTT / Hurricane 400 XTT – Traction
Batteries: removal
! INFORMATION: The batteries must be removed by qualied technical personnel.
! DANGER: When removing the batteries, the operator must be equipped with suitable personal protection devices (gloves, goggles,
overalls, safety shoes, etc.) to reduce the risk of injury. Make sure to remove the electronic key from the panel before proceeding. Keep
away from naked ames, do not short circuit the battery poles, do not cause sparks and do not smoke.
Proceed as follows:
• Disconnect the battery cables and bridge terminals from the battery poles.
• If necessary, remove the devices xing the battery to the base of the machine.
• Lift the batteries from the compartment using suitable lifting equipment.
Choosing a battery charger
Specic chargers are required for optimal performance of both Deep Cycle (Lead-Acid) and AGM batteries. Consult Dustbane
literature/distributor to determine which charger is best. Refer to charger literature for more information.
Lifting and transporting the machine
! WARNING: All phases of lifting and moving must be performed in an adequately illuminated environment with the adoption of the
safety measures most appropriate to the situation.The operator must always use personal protection devices.
Proceed as follows to load the machine onto a means of transport:
• Empty the tanks.
• Remove the batteries.
• Push the machine onto the pallet using a sloping ramp, securing the front wheels and the chassis using the brackets
supplied. The machine must not be raised.
• Lift the pallet (with the machine) using a fork lift truck and load it onto the means of transport.
• Anchor the machine to the means of transport with cables connected to the pallet and to the machine itself.
PRACTICAL GUIDE FOR THE OPERATOR
! WARNING: Before starting work, wear overalls, ear protectors, non-slip and waterproof shoes, mask to protect the respiratory tract,
gloves and all other personal protection devices necessitated by the work environment.
! WARNING: Never leave the machine unattended or parked with the electronic ignition key inserted.
! INFORMATION: If you are using the machine for the rst time, we recommend trying it out on a large obstacle-free surface rst
to acquire the necessary familiarity.
! WARNING: To avoid damaging the surface of the oor you are cleaning, avoid rotating the brushes with the machine stationary.
! WARNING: Always dilute the detergent according to the manufacturer’s instructions. Do not use sodium hypochlorite (bleach)
or other oxidants, particularly in strong concentrations. Do not use solvents or hydrocarbons. The water and detergent temperature
must not exceed the maximum indicated in the “Technical specications”. They must be free of sand and/or other impurities.
The machine has been designed for use with low-foam biodegradable detergents made specically for scrubber dryers.
For a complete and up-to-date list of the detergents and chemicals available, contact the Manufacturer.
Use products suitable for the oor and dirt to be removed only.
Follow the safety regulations on use of detergents given in the section “Safety regulations”.
10 Operations Manual Hurricane 400 XTT / Hurricane 400 XTT – Traction
Squeegee adjustment
Fig./Abb./
图
7
Fig./Abb./
图
9 Fig./Abb./
图
8
Fig./Abb./
图
10 Fig./Abb./
图
11
1
3
2
4
5
To mount the squeegee on the machine, proceed as follows:
• Check that the squeegee mount (ref. 2) is raised, otherwise lift it by means of the squeegee lever (ref. 5);
• Insert the suction hose sleeve (ref. 4) fully into the squeegee;
• Slacken the two knobs (ref. 3) at the centre of the squeegee;
• Insert the two threaded pins into the slots on the support (ref. 2);
• Fix the squeegee by tightening the two knobs (ref. 3).
The squeegee blades scrape the lm of water and detergent from the oor and prepare the way for perfect drying. With time, the
constant rubbing makes the edge of the blade in contact with the oor rounded and cracked, reducing the drying eciency and
requiring it to be replaced. The state of wear should be checked frequently.
For perfect drying, the squeegee must be adjusted in such a way that the edge of the rear blade bends during operation by about
45° with respect to the oor at every point. Adjust the angle of the blade during operation by regulating the height of the two
wheels positioned behind the squeegee (ref. 1).x).
Moving the machine when not in operation
Proceed as follows to move the machine:
• Raise the squeegee.
• Raise the head.
• Move the machine as follows:
Non-Traction units: push or pull;
Traction units: to move the machine forwards, press the button/selector and then operate the drive lever. To move the machine
backwards, press the button/selector again then operate the drive lever. Speed can be varied by the potentiometer knob.
Once you have reached your destination, lower the head by pressing the release pedal down and to the left, then release it.
11Operations Manual Hurricane 400 XTT / Hurricane 400 XTT – Traction
Mounting and changing the brush/drive disks
Fitting the brush/pad: Rest the brush on the oor in front of the machine and center it with the guard. Lower the head and
repeatedly action the brush/drive control lever until the brush automatically engages on the ange hub. If the maneuver is not
successful, press on the handle again and repeat the centering and repeated actioning of the brush/drive lever.
Removing the brush/pad: Raise the machine head by pushing the head lift pedal down and then to the right and repeatedly
action the brush/drive lever. After a few pulses, the brush/es (or drive disk) is released and falls to the ground.
Detergents – Instructions
! INFORMATION: Always dilute the detergent according to the manufacturer’s instructions. Do not use bleach or other oxidants, particu-
larly in strong concentrations. Do not use solvents or hydrocarbons. The temperature of the water and detergent must not exceed the
maximum indicated in the technical specication. They must be free of sand and/or other impurities.
The machine has been designed for use with low-foam biodegradable detergents made specically
for automatic scrubbers. For a complete and up-to-date list of the detergents and chemicals available, contact the manufacturer.
Use products suitable for the oor and dirt to be removed only. Follow the safety regulations
on use of detergents given in the section “Safety regulations”.
Preparing the machine for work
Before starting work, proceed as follows:
• Check the battery charge (recharge if necessary);
• Lower the head;
• Make sure the recovery tank is empty. If necessary, empty it;
• Check that the tap lever is in the “CLOSED” position;
• Fill the solution tank with a suitable concentration of clean water and low-foam detergent. Leave at least 5 cm between
the surface of the liquid and the opening of the tank;
• If the machine is tted with the optional CHEM DOSE accessory, remove the cap and ll the tank with appropriately
diluted low-foam detergent.
• Mount the most suitable brushes / pads for the oor and work to be performed;
• Make sure the squeegee is rmly attached and connected to the suction hose. Make sure the back blade is not worn.
For eective cleaning and to extend the working life of the machine, follow a few simple rules:
• Prepare the work area by removing all possible obstacles;
• Begin working from the furthermost point to avoid walking on the area you have just cleaned;
• Choose the straightest possible working routes;
• Divide large oors into parallel rectangular sections.
• If necessary, nish o by passing a mop or rag rapidly over parts inaccessible to the auto-scrubber.
12 Operations Manual Hurricane 400 XTT / Hurricane 400 XTT – Traction
Working
After setting up the machine, proceed as follows:
• Connect the machine as follows:
• Move the tap lever to the minimum detergent ow position. The detergent solution starts owing to the brush;
• Lower the squeegee by means of the corresponding lever;
• Press the brush switch;
• Press the suction switch to start the suction motor;
• Press the brush/drive lever;
Non-Traction units:
• When the brush switch is in the “1” position and the drive lever is pulled, the motor which turns the brush and moves the
machine starts up. A special mechanical drive device uses the friction between the brush and oor to generate a forward
movement. When the mechanical drive lever is released, the brush motor shuts down and the machine stops.
If the machine pulls to one side, restore a straight course by using the direction regulation knob. If the machine pulls to
the right, turn the knob clockwise and vice versa.
Finishing Work
• Place the tap lever in the “CLOSED” position;
• Release the brush/drive lever located under the handgrip. This turns the brush/drive motor o and the machine stops;
• Stop the brush / pad;
• Lift the lever to raise the squeegee from the oor to prevent the continuous pressure from warping the blades;
• Let the suction motor run for at least 2 minutes to make sure it is completely dry, then press “0”
on the suction switch to switch o the suction motor;
• Remove the brushes (or drive pads) to prevent them from warping permanently;
• Press the button to turn the optional CHEM DOSE accessory o;
• Depending on the model, disconnect the ANDERSON connectors;
• Empty and clean the dirty recovery tank.
Some useful tips to get the most from your scrubber dryer
In the event of particularly stubborn dirt on the oor, washing and drying can be performed in two separate operations.
Pre-washing with brushes or pads:
• Select the Brush operating program.
• Activate the drive lever, start working.
• If necessary, adjust the ow of detergent delivered to the brush; the outlet ow must be metered in relation to the
required travel speed; the slower
the machine travels, the less detergent must be delivered.
• Persist when washing particularly dirty points to give the detergent time
to perform its chemical action detaching
and suspending the dirt and the brushes time to exert an eective mechanical action.
Drying
• Select the Suction operating program, lower the squeegee.
• Activate the drive lever, start working.
• Pass over the same area washed previously. The result is equivalent to
in-depth washing and subsequent ordinary maintenance will take less time.
13Operations Manual Hurricane 400 XTT / Hurricane 400 XTT – Traction
Draining the dirty water
The dirty recovery tank drain hose is at the back left side of the machine.To empty the tank:
• Move the machine near a drain;
• Detach the drain hose (ref. 2) from its seat by holding it near the xing spring (ref. 3) and pulling horizontally;
• Keeping the hose end as high as possible, unscrew and remove the cap (ref. 4);
• Lower the hose end gradually, controlling the intensity of the ow of water by adjusting the height
from the ground;
• Check the amount of dirt left in the dirty water drum and if necessary wash it out. To facilitate cleaning
and complete emptying of the drum, you are recommended to unfasten and lift it;
• When the dirty water has been totally drained, lower the dirty water drum (if previously lifted) and refasten to the
detergent tank;
• Close the drain hose (ref. 2) by replacing the cap (ref. 4), check that it is tightly closed and replace
the hose in its housing.
Fig./Abb./
图
7
Fig./Abb./
图
9 Fig./Abb./
图
8
Fig./Abb./
图
10 Fig./Abb./
图
11
1
3
2
4
5
Draining the clean water
To empty the tank:
• Move the machine near a drain;
• Unclip the drain hose from the lower right hand backside of the machine;
• When the solution tank is completely empty, replace the cap.
Periods Of Inactivity
If the machine is not used for some time, remove the squeegee and brushes / pads, wash them and put them away in a dry place
(preferably in a bag or wrapped in plastic lm) away from dust. Park the machine with
the head lowered. Make sure the tanks are completely empty and perfectly clean.
Disconnect the machine from the power supply (disconnect the ANDERSON connector from the battery wiring).
Batteries: Completely recharge the batteries before storing them. During long periods of inactivity, you should charge the
batteries regularly (at least once every two months) to keep them constantly at maximum charge.
Battery maintenance and charging
See appropriate Dustbane literature for specics on battery maintenance and charging.
14 Operations Manual Hurricane 400 XTT / Hurricane 400 XTT – Traction
MAINTENANCE INSTRUCTIONS
! DANGER: Never perform any maintenance operations without rst disconnecting the batteries. Maintenance on the electrical circuit and
all other operations not explicitly described in this manual must be performed by specialized personnel only, in compliance with current
safety legislation and
as described in the maintenance manual.
! DANGER: Before lifting/rotating the tank to access the compartment, its contents must rst be emptied, then insert the safety bracket in
position to prevent the tank from accidentally closing again, see chapter “SAFETY INFORMATION”.
Maintenance - General rules
Performing regular maintenance according to the Manufacturer’s instructions improves performance and extends the working life
of the machine.
When cleaning the machine, observe the following precautions:
• Avoid using pressure washers. Water could penetrate the electrical compartment or motors leading to damage or short
circuits.
• Do not use steam to avoid the heat warping plastic parts.
• Do not use solvents or hydrocarbon based products. These can damage the cowling and rubber components.
Suction motor air lter and oat switch: cleaning
Fig./Abb./
图
7
Fig./Abb./
图
9 Fig./Abb./
图
8
Fig./Abb./
图
10 Fig./Abb./
图
11
1
3
2
4
5
• Unscrew and remove the tank cap (ref. 1) from the dirty water drum (ref. 4);
• Make sure the dirty water drum (g. 10, ref. 4) is empty;
• Clean the oat switch (ref. 5) at the back of the dirty water drum, taking care not to direct the water jet directly against
the oat switch;
• Remove the suction motor air lter (ref. 2) from the oat switch support (ref. 3) inside the dirty water drum at the top;
• Clean the lter with running water or the detergent solution used on the machine;
• Dry the lter thoroughly before replacing it in the support. Make sure the lter is correctly located
in its housing;
• Screw the cap back on the dirty water drum.
Basket lter: cleaning
• Remove the basket lter from the water ll hole at the front of the machine;
• Clean the lter with running water or the detergent solution used on the machine;
• Replace the lter back in its housing, making sure it is correctly positioned.
15Operations Manual Hurricane 400 XTT / Hurricane 400 XTT – Traction
Detergent lter: cleaning
Fig./Abb./
图
7
Fig./Abb./
图
9 Fig./Abb./
图
8
Fig./Abb./
图
10 Fig./Abb./
图
11
1
3
2
4
5
• Unscrew the screw located below the bottom tank (ref. 1);
• Unscrew the detergent lter (ref. 2);
• Clean the lter with running water or the detergent solution used on the machine;
• Replace the lter back in its housing, making sure it is correctly positioned and retighten the screw.
Squeegee blades: replacing
The squeegee blades collect the lm of water and detergent from the oor and prepare the way for perfect drying. With time, the
constant rubbing leaves the edge of the blade in contact with the oor rounded and cracked, reducing the drying eciency and
requiring it to be replaced.
Turning or replacing the squeegee blades:
Fig./Abb./
图
12
Fig./Abb./
图
13 Fig./Abb./
图
14
Fig./Abb./
图
15
A
• Lower the squeegee by using the squeegee lever;
• Remove the squeegee from its mount by completely unscrewing the two knobs;
• Remove the suction hose sleeve from the squeegee;
• Release the catch (ref. 3 or 6);
• Remove the two blade retainers (ref. 2 or 7) by rst pushing them towards the body of the squeegee (ref.1) then
extracting them;
• Remove the blade (ref. 4 or 5);
• Reuse the same blade by reversing the edge in contact with the oor until all four edges are worn out,
or replace with a new blade, tting it onto the screws on the body of the squeegee (ref. 1);
• Reposition the two blade retainers (ref. 2 or 7) by centering the widest part of the slots over the xing screws on the
squeegee body (ref. 1), then pushing the blade retainers inwards;
• Refasten the catch (ref. 3 or 6).
• Replace the squeegee in its support
16 Operations Manual Hurricane 400 XTT / Hurricane 400 XTT – Traction
Fuses: replacing
! WARNING: Never use a fuse with a higher amperage than specied.
The fuses can only be replaced by a Dustbane service centre or by technical personnel authorized by Dustbane.
Fig./Abb./
图
12
Fig./Abb./
图
13 Fig./Abb./
图
14
Fig./Abb./
图
15
A
The fuses protecting the brush and suction motors are located in the fuse holder (ref. 1) attached to the recovery tank above the
machine battery compartment.
To replace the fuses:
• Make sure the dirty water drum is empty and empty if necessary;
• Raise the dirty water drum;
• Raise the fuse holder cover and remove the fuse by unscrewing the xing screws;
• Fit a new fuse and close the fuse holder cover;
• Lower the dirty water drum.
• Fuse table: For the complete fuse table, see the spare parts catalogue.
If a fuse continues to blow, the fault in the wiring, boards (if present) or motors must be identied and repaired. Have the machine
checked by qualied personnel.
Dustbane Products Ltd., 25 Pickering Pl., Ottawa, ON K1G 5P4
•
Tel: 1-800-387-8226 Fax: 1-800-363-5309 www.dustbane.ca
Product Warranty
Dustbane Products Ltd.
Your new product from Dustbane Products Limited is covered by a full warranty from the date
ofpurchase. This includes all new units and accessories (some exceptions apply) manufactured
orsupplied by Dustbane Products Limited and delivered to the original retail purchaserby an
authorizedDustbane distributor.
Should your product have a defect in material or workmanship under normal use and care within the
warranty period outlined below, Dustbane shall arrange to have the original product returned to our
head oce or toan authorized service center for repair, replacement or refund.
WHAT IS COVERED
Reservoirs
TEN (10) YEARS unconditional warranty on all
polyethelene rotational molded reservoirs to be
freefromall cracks and/or corrosion.
Parts
THREE (3) YEARS unconditional warranty on all
equipment parts against defects in material and
workmanship under normal use and care with the
exception of any rubber components and springs.
Labour
ONE (1) YEAR year unconditional warranty on labour
based on Dustbane’s Labour Rates and equipment parts
under normal use and care with theexception of any
rubber components and springs.
EXEMPTIONS
The following products are exempt from this warranty
andalternate conditions may apply:
• Batteries
• Chargers
WHAT IS NOT COVERED
The provisions of this Warranty shall not apply to:
• any unit of Dustbane Equipment which has been subject
to misuse, negligence, accident, use of inappropriate
accessories, parts or chemicals, or serviceby an
unauthorized Dustbane repair depot.
• normal maintenance services and the replacement
of service items (including but not limited to electric
cord, painted parts, any rubber parts and springs,
switch and bearings) made in connection with such
services as required in the Dustbane Recommended
MaintenanceSchedule.
• the following parts and/or accessories are not covered
under the warranty:
Rubber parts Springs
Electric cord Painted parts
Switch Bearings
Belts Squeegee Blades
Pad Drivers or Brushes Floor Pads
Gaskets Filters
External Hoses Fuses
WARRANTY CARD
Model Name:
Model Number:
Serial Number:
Date of Purchase:
Purchased From:
Use this card for quick access to your product information
(information purposes only)
18 Operations Manual Hurricane 400 XTT / Hurricane 400 XTT – Traction
Periodic Checks
Checks
Daily
Operations
Weekly
Operations
Six Monthly
Operations
Cleaning the dirty water tank X
Cleaning the suction oats
Cleaning the water/detergent tank lter X
Cleaning the suction lter X
Cleaning the front squeegee suction hose X
Cleaning the rear squeegee suction hose X
Cleaning the diverter valve X
Cleaning the squeegee blades X
Checking squeegee blade wear X X
Checking brush wear X
Recharge batteries X
Disconnect machine from power supply X
Emptying the recovery tank X X
Have electrical circuit checked by qualied personnel X
Troubleshooting
[TR]= only applies to electric drive (traction) unit
Problem Cause Remedy
The machine does not
function
Battery connector disconnected. Connect the batteries to the machine.
The batteries are at. Recharge the batteries
The brushes
do not turn
The brush switch in the “0” position. Place the brush switch in the “1” position.
[TR] You have not used the brush switch. Press the brush switch.
You have not pressed the brush lever. Press the brush lever.
The motor thermal cutout has tripped; the motor
is overheated.
Release the brush lever, turn the brush switch to the
“0” position (o); leave the machine to cool down
for at least 45 min.
19Operations Manual Hurricane 400 XTT / Hurricane 400 XTT – Traction
The power supply or motor thermal cutout
connectors are disconnected.
Reconnect the power supply or motor thermal
cutout connectors.
The brush motor fuse has blown. Have someone check and eliminate the causes
responsible for the blown fuse, then replace.
The batteries are at. Recharge the batteries.
The reduction unit is faulty. Have the reduction unit replaced.
The motor is faulty. Have the motor replaced.
The machine does
not clean evenly
The brush or disks are worn. Replace. See Parts List.
No detergent
is delivered
The tap lever is in the “CLOSED” position. Move the lever to the “OPEN” position.
The detergent tank is empty. Fill it.
The hose delivering the detergent to the brush is
blocked.
Unblock and open the circuit.
The tap is dirty or faulty. Clean or replace the tap by unscrewing the screw .
The detergent ow
does not stop
The tap stays open, because it is damaged or very
dirty.
Have the tap cleaned or replaced.
The suction motor does
not start
The suction switch is in the ‘0’ position (o). Turn the suction switch on.
There is no power to the suction motor or
the motor is faulty.
Check that the motor power connector is correctly
connected to the main wiring; in the second case
have the motor replaced.
The fuse has blown. Replace the fuse.
The squeegee does not
clean or suction
is ineective
The edge of the rubber blades in contact with
the oor is worn.
Replace the rubber blade.
The squeegee or hose is blocked or damaged. Unblock and repair the damage.
The oat switch has tripped (dirty water drum),
is clogged by dirt or broken.
Empty the dirty water drum or reset the oat
switch.
The suction hose is blocked. Unblock the hose.
The suction hose is not connected to the squeegee
or is damaged.
Connect or repair the hose.
There is no power to the suction motor or the
motor is faulty.
Check that the motor power connector is correctly
connected to the main wiring and that the fuse
is not blown; in the second case have the motor
replaced.
The machine does not
move
There is no power to the brush/drive motor
or it is faulty.
In the rst case, place the brush switch in the “1”
position and press the brush/drive lever; in the
second case, check that the brush/drive motor is
correctly connected to the main wiring; in the third
case replace the motor.
The reduction unit is broken (therefore the brush
does not turn).
Have the reduction unit replaced.
The brush motor thermal cutout has tripped;
the motor is overheated.
Stop the machine, turn it o and leave it to cool
for at least 45 min.
The batteries are at and the brushes have shut down. Recharge the batteries.
The machine tends
to pull to one side
The direction adjustment knob must be adjusted
appropriately for the oor.
Regulate the direction of movement by adjusting
the direction adjustment knob on the bottom left
backside of the machine.
20 Operations Manual Hurricane 400 XTT / Hurricane 400 XTT – Traction
The batteries do not
provide the normal
work time
The battery poles and charging terminals are dirty
and oxidised.
Clean and grease the poles and terminals, recharge
the batteries.
The electrolyte level is low. Top up all the elements with distilled water
as described in the instructions.
The battery charger does not work or is unsuitable. See battery charger instructions
There are considerable dierences in density
between the various elements of the battery.
Replace the damaged battery.
You are using the machine with excessive pressure
on the brushes.
Reduce pressure on the brush.
There are considerable dierences in density
between the various elements of the battery.
Replace the damaged battery.
The battery discharges
too fast during use,
even though it has
been charged correctly
and when tested with a
hydrometer at the end
of recharging, it turned
out to be uniformly
charged
The battery is new and does not deliver 100%
of its expected capacity.
The battery must be “run-in” by performing 20-
30 charges and discharges to obtain maximum
performance.
The machine is being used at maximum capacity
for continuous periods and the working time is not
sucient.
If possible, use batteries with a higher capacity
or replace the batteries with others charged
previously.
The electrolyte has evaporated and does not cover
the plates completely.
Top up all elements with distilled water until the
plates are covered then recharge the battery.
Display Alarms
Alarm Error indicator
NAN “Drive Lever” already pressed when the machine is turned on or after an Emergency.
SIC Emergency button pressed
POT Speed potentiometer fault.
MOS Board (mosfet) short circuit.
HOT Motor thermal cutout tripped.
LIM Board (mosfet) thermal limitation problem.
BLT Drive block. Appears when the battery voltage is too low and the drive is blocked.
AcS
Brush Control Fault Appears when there is a fault in the solenoid switch controlling the
brushes.
AcA
Suction control fault. Appears when there is a fault in the solenoid switch controlling
suction.
FuP Fuse. Appears when the fuse is blown.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
Dustbane Hurricane 400 XTT Traction Operations Manual
- Catégorie
- Scrubber
- Taper
- Operations Manual
- Ce manuel convient également à
dans d''autres langues
- English: Dustbane Hurricane 400 XTT Traction
Documents connexes
-
Dustbane Hurricane 690 XTT Operations Manual
-
-
-
-
-
-
-
-
-
Dustbane Power Clean 900 XT Operations Manual
