Dormakaba LA GARD 700 Series Mode d'emploi

700 Series Anleitung für

Systembenutzer

Guia do Usuário do Sistema

Podręcznik użytkownika systemu

Select a Language

700 Series System User Guide

Guide de l'utilisateur du système

Guía del usuario del sistema

0 | Page

LA GARD SERIES 700

System User Guide

For Models 701-705

dormakaba USA Inc. System User Guide 7040.1121 Rev E2 10/22 | 1

Table of Contents

1 Introduction .............................................................................................. 6

1.1 Approved Standards ................................................................................................................... 6

1.2 Electrical Precautions ................................................................................................................ 7

1.3 Tools ............................................................................................................................................. 7

2 Typical System Layout (Single & Multi) ............................................... 8

2.1 Safe Lock Hardware ................................................................................................................... 9

2.2 System Components .................................................................................................................. 9

2.2.1 Keypad .......................................................................................................................................................... 9

2.2.2 Multiplexer .................................................................................................................................................. 9

2.2.3 Safe Lock ..................................................................................................................................................... 9

2.2.4 AC Adapter ................................................................................................................................................. 9

2.2.5 Battery Box................................................................................................................................................. 9

2.2.6 Alarm Box .................................................................................................................................................... 9

2.2.7 Reset Box................................................................................................................................................... 10

2.2.8 Fob .............................................................................................................................................................. 10

2.2.9 Power Considerations ............................................................................................................................ 10

2.3 Getting Started ......................................................................................................................... 11

3 How to Use the System ......................................................................... 11

3.1 Keypad Model Definitions ......................................................................................................... 11

3.2 Keypad – Layout, Usage, and Settings .................................................................................. 14

3.2.1 Keypad Layout & General Usage ...........................................................................................................14

3.2.2 Using a Display Keypad – Menu Settings............................................................................................14

3.2.3 Using a Non-Display Keypad - # Commands .....................................................................................16

3.3 System Functions ..................................................................................................................... 16

3.3.1 System Info (Display Only) ..................................................................................................................... 17

3.3.2 Backlight Mode ........................................................................................................................................ 18

3.3.2.1 Backlight Mode – Display Keypad ....................................................................................................................18

3.3.2.2 Backlight Mode – 702 Keypad (Non-Display) ...............................................................................................18

3.3.3 Buzzer Mode ............................................................................................................................................. 18

3.3.3.1 Buzzer Mode – Display Keypad .........................................................................................................................18

3.3.3.2 Buzzer Mode – Non-Display Keypad ............................................................................................................... 19

3.3.4 Combination Length ................................................................................................................................19

dormakaba USA Inc. System User Guide 7040.1121 Rev E2 10/22 | 2

3.3.4.1 Combo Length – Display Keypad ..................................................................................................................... 19

3.3.4.2 Combo Length – Non-Display Keypad............................................................................................................ 19

3.3.5 Force Change Combination ...................................................................................................................19

3.3.5.1 Force Change Combination – Display Keypad ............................................................................................. 20

3.3.5.2 Force Change Combination – Non-Display Keypad ................................................................................... 20

3.3.6 User Mode ................................................................................................................................................. 20

3.3.6.1 User Mode – Display Keypad............................................................................................................................ 20

3.3.6.2 User Mode – Non-Display Keypad ................................................................................................................... 21

3.3.7 Credential Mode (703B, 704B, and 705 Models Only) ..................................................................... 21

3.3.8 Duress Mode (Silent Alarm) .................................................................................................................. 21

3.3.8.1 Duress Mode – Display Keypad ........................................................................................................................ 21

3.3.8.2 Duress Mode – Non-Display Keypad ............................................................................................................. 22

3.3.9 Input Signal ............................................................................................................................................... 22

3.3.9.1 Input Signal – Display Keypad ......................................................................................................................... 22

3.3.9.2 Input Signal – Non-Display Keypad ............................................................................................................... 23

3.4 Users .......................................................................................................................................... 23

3.4.1 Lock User Types........................................................................................................................................ 23

3.4.1.1 Master ................................................................................................................................................................... 23

3.4.1.2 Manager ............................................................................................................................................................... 24

3.4.1.3 Standard Users ................................................................................................................................................... 24

3.4.2 User Privileges .......................................................................................................................................... 24

3.4.2.1 User Privileges – Access Lock........................................................................................................................... 24

3.4.2.2 User Privileges – Audit Lock ............................................................................................................................ 25

3.4.2.3 User Privileges – Time Delay Override with Combination ......................................................................... 25

3.4.2.4 User Privileges – Time Delay Override with Fob Credential ..................................................................... 25

3.4.3 Assigning User IDs and Privileges ........................................................................................................ 28

3.4.3.1 Add User – Display Keypad .............................................................................................................................. 28

3.4.3.2 Add User – Non-Display Keypad ..................................................................................................................... 29

3.4.4 Edit User .................................................................................................................................................... 29

3.4.4.1 Edit User – Display Keypad .............................................................................................................................. 29

3.4.4.2 Edit User – Non-Display Keypad..................................................................................................................... 30

3.4.5 Delete User ................................................................................................................................................ 31

3.4.5.1 Delete User – Display Keypad ........................................................................................................................... 31

3.4.5.2 Delete User – Non-Display Keypad ................................................................................................................. 31

3.5 Install (Electronically Pair) a Lock and Keypad .................................................................... 31

3.5.1 Install (Electronically Pair) Lock and OLED Display Keypad .......................................................... 31

3.5.2 Install (Electronically Pair) Lock and non-Display Keypad ............................................................ 32

3.5.2.1 Standard Install Process ................................................................................................................................... 32

dormakaba USA Inc. System User Guide 7040.1121 Rev E2 10/22 | 3

3.5.2.2 Install with a Preconfigured User ................................................................................................................... 33

3.6 Open a Lock .............................................................................................................................. 34

3.6.3 Open a Lock – Display Keypad ............................................................................................................. 34

3.6.4 Open a Lock – Non-Display Keypad .................................................................................................... 34

3.6.5 Open a Lock – Remote Disable ............................................................................................................. 34

3.7 Change Combination ............................................................................................................... 35

3.7.1 Change Combination – Display Keypad .............................................................................................. 35

3.7.2 Change Combination – Non-Display Keypad .................................................................................... 35

3.8 Reinstall Keypad ...................................................................................................................... 36

3.9 Change Time/Date/DST ......................................................................................................... 36

3.9.1 Change Time/Date/DST – Display Keypad ....................................................................................... 36

3.9.2 Change Time/Date/DST – Non-Display Keypad .............................................................................. 37

3.10 Battery Levels......................................................................................................................... 37

3.10.1 Low Battery Warning ........................................................................................................................... 37

3.10.1.1 Low Battery Warning – Display Keypad ...................................................................................................... 37

3.10.1.2 Low Battery Warning – Non-Display Keypad ............................................................................................ 38

3.10.2 Critical Low Battery Warning ............................................................................................................ 38

3.10.2.1 Critical Low Battery Warning – Display Keypad ....................................................................................... 38

3.10.2.2 Critical Low Battery Warning – Non-Display Keypad ............................................................................. 38

3.10.3 Replacing Batteries in Critical Low Battery State ........................................................................ 38

3.11 View Audits (Display Keypad Only) ..................................................................................... 38

3.12 Wrong Try Penalty .................................................................................................................. 39

3.13 Locks ........................................................................................................................................ 39

3.13.1 Physical Installation of a Lock ............................................................................................................. 39

3.13.2 Uninstall (Electronically Un-pair) a Lock .......................................................................................... 39

3.13.2.1 Uninstall a Lock – Display Keypad ................................................................................................................. 39

3.13.2.2 Uninstall a Lock – Non-Display Keypad ....................................................................................................... 40

3.13.3 Reset a Lock ........................................................................................................................................... 40

3.13.3.1 Master Reset – Display Keypad ..................................................................................................................... 40

3.13.3.2 Master Reset – Non-Display Keypad ............................................................................................................ 41

3.13.3.3 Mechanical Reset............................................................................................................................................... 41

3.14 Time Delay ............................................................................................................................... 41

3.14.1 Enable/Disable Time Delay ...................................................................................................................41

3.14.1.1 Enable/Disable Time Delay – Display Keypad .............................................................................................. 41

3.14.1.2 Time Delay Count Mode – Display Keypad .................................................................................................. 42

3.14.1.3 Enable/Disable Time Delay – Non-Display Keypad ................................................................................... 43

3.14.2 Open a Lock During Time Delay .......................................................................................................... 43

dormakaba USA Inc. System User Guide 7040.1121 Rev E2 10/22 | 4

3.14.2.1 Open a Lock During Time Delay – Display Keypad .................................................................................... 43

3.14.2.2 Open a Lock During Time Delay – Non-Display Keypad ........................................................................... 43

3.14.3 Cancel a Time Delay .............................................................................................................................. 44

3.14.3.1 Cancel a Time Delay – Display Keypad ......................................................................................................... 44

3.14.3.2 Cancel a Time Delay – Non-Display Keypad ............................................................................................... 44

3.14.4 Allow Time Delay Override .................................................................................................................. 44

3.14.4.1 Allow Time Delay Override – Display Keypad ............................................................................................ 44

3.14.4.2 Allow Time Delay Override – Non-Display Keypad .................................................................................. 45

3.14.5 Open Lock During Time Delay Using Override with Combo ......................................................... 45

3.14.5.1 Open Lock During Time Delay Using Override with Combo – Display Keypad .................................... 45

3.14.5.2 Open Lock During Time Delay Using Override with Combo – Non-Display Keypad ........................... 45

3.14.6 Open Lock During Time Delay Using Override with FOB .............................................................. 45

3.15 Auto Open................................................................................................................................ 47

3.15.1 Aspects of Auto Open ........................................................................................................................... 47

3.15.1.1 Auto Open Interactions with other features ............................................................................................... 48

3.15.1.2 Auto Open Feedback ........................................................................................................................................ 48

3.15.1.3 Auto Open Feedback with battery level low or critical............................................................................. 49

3.15.2 Configure Auto Open – Display Keypad ........................................................................................... 49

3.16 Assign Time Lock Schedules ................................................................................................. 50

(704 & 705 Models Only) .............................................................................................................. 50

3.17 Time/Date Rules in LA GARD 700 Series Locks ................................................................. 50

3.18 FOB Identification Feedback................................................................................................. 52

3.18.1 FOB Credential Feedback .................................................................................................................... 52

3.18.2 FOB Low Battery and Critical Indicator .......................................................................................... 52

4 System Security ..................................................................................... 52

4.1 Data Encryption ........................................................................................................................ 52

4.2 Initial Combination Handling .................................................................................................. 53

5 LA GARD Software ............................................................................... 53

5.1 Adding a User with LA GARD Software ................................................................................. 53

5.2 Install a User into the Keypad ................................................................................................. 54

5.3 Firmware Update ..................................................................................................................... 54

5.4 Retrieve Audits ......................................................................................................................... 56

5.5 Add Time Lock Schedules using LA GARD Software (704 & 705 Models Only) ................ 57

Appendix A: List of Audits ....................................................................... 58

Appendix B: LA GARD 700 Series Release Notes ................................. 59

dormakaba USA Inc. System User Guide 7040.1121 Rev E2 10/22 | 5

Appendix C: LA GARD 700 Series Simple Set-Up: 701 with 1

Manager/1 Standard User/6 Digit Combination .................................. 64

Appendix D: LA GARD 700 Series Simple Set-Up: 702 with 1

Manager/1 Standard User/6 Digit Combination .................................. 68

dormakaba USA Inc. System User Guide 7040.1121 Rev E2 10/22 | 6

1 Introduction

This guide outlines general information for using and programming LA GARD 700 Series Models 701-

705 electric combination safe locks and all its components, including accessories and software client.

This guide assumes the installer has knowledge of electrical, mechanical, and computer concepts, as

well as having familiarity with safe lock systems and associated components. For reliable and safe

operation of the equipment, comply with all safety precautions outlined in this guide.

1.1 Approved Standards

The LA GARD family of safe locks conform to the following approved standards:

• UL 2058 (High Security Electronic Locks)

• EN 1300:2018

• Model: 705 – FCC ID: 2ASNP-705, IC ID: 24793-705

• Model: DKLG70X – FCC ID: 2ASNP-DKLG70X, IC ID: 24793-DKLG70X

• VDS 2395 Class 2, Models: 701-704

• SBSC 3880:2015, Models: 701-704

• CNPP A2p – Level B/E, Models: 701-704

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by dormakaba USA Inc. could void the user's authority to

operate the equipment.

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and

Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause undesired operation of the

device.

dormakaba USA Inc. System User Guide 7040.1121 Rev E2 10/22 | 7

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation,

Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes :

1. L’appareil ne doit pas produire de brouillage.

2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement.

CET APPAREIL EST CONFORME À LA NORME RSS INDUSTRIE CANADA EXEMPT DE LICENCE. Son

fonctionnement est soumis aux deux conditions suivantes:(1) Cet appareil ne doit pas provoquer

d’interférenceset(2) Cet appareil doit accepter toute interférence, y compris les interferences pouvant causer

un mauvais fonctionnement du dispositif. Cet appareil numérique de la classe [B] respecte toutes les exigences

du Réglement sur le matériel brouilleur du Canada.

1.2 Electrical Precautions

Ensure alkaline batteries (where applicable) are new and in good condition; leaking batteries can cause damage

to components and can also cause serious bodily harm. Do not apply power (where applicable) before

completing all steps of the installation; doing so may damage the components. Ensure all power supplies are

plugged into grounded electrical receptacles that comply with local building code(s). When AC mains power is

required the power supply shall be installed in accordance with NFPA 70 and any applicable electrical codes.

1.3 Tools

dormakaba USA Inc. recommends having the following tools on hand to install LA GARD safe locks and their

components:

• Digital voltmeter

• Wire cutters and needle nose pliers

• Set of screwdrivers

• Drill and drill bits

• Automatic saw (band saw, hand saw)

• US or Metric taps

• File or equivalent tool

• All installation/hardware documentation for quick reference

dormakaba USA Inc. System User Guide 7040.1121 Rev E2 10/22 | 8

2 Typical System Layout (Single & Multi)

The following sub-sections review safe lock system components with related diagrams. Refer to each product’s

individual documentation for more detailed information on hardware installation and proper device usage.

The following diagrams (Figures 1 and 2) show completed system layouts for both single and multi-lock

systems. Please note that your system may not include all components shown.

Figure 1 – Single Lock System

Battery box, alarm

box, or AC adaptor

LA G AR D Prg m C able

LA G AR D Key pad

Swingbolt Safe Lock

Figure 2 – Multi-Lock System

Battery box, alarm

box, or AC adaptor

LA G ARD Prg m Cable

LA G ARD Key pad

Lock #1

Multiplexor

Swingbol t Safe Lo ck

dormakaba USA Inc. System User Guide 7040.1121 Rev E2 10/22 | 9

2.1 Safe Lock Hardware

The LA GARD System components have been tested as compatible with the LA GARD system and should not

be substituted. Consult each component’s individual documentation for proper mounting, connectivity, and

installation. The safe itself must be appropriate for the lock hardware to provide maximum security; certain

makes and models of safes may not be appropriate for this LA GARD safe lock system. If unsure, consult with

dormakaba USA Inc. Sales or Support for further information.

2.2 System Components

Each system may differ depending on customer requirements. The sub-sections outlined below cover the full

suite of the LA GARD safe lock system.

2.2.1 Keypad

The Keypad comes in two varieties: Display and non-Display. The Display variant shows messages on screen

while the non-Display version implements a series of LED flashes and beeps for messages. The Keypad is the

user interface for the entire system. All Keypads are available in both Tamper Evident and Serviceable options,

which will impact how the keypad is physically mounted. Refer to the Keypad Installation Guide (Document

#7033.0322) for more information.

2.2.2 Multiplexer

The Multiplexer is used in multi-lock systems and allows multiple safe locks to connect with the Keypad. Refer to

the Multiplexer Installation Guide (Document #7038.0521) for more information. The Multiplexer is not UL

evaluated. (Item/Order # 704033, “Multiplexer”)

2.2.3 Safe Lock

The safe lock is either a dead bolt, a spring bolt, or a swing bolt, that locks and unlocks when the Keypad

receives correct user credentials. This lock system comes in many varieties depending on the application. Refer

to the Safe Lock Installation Guide (Document # 7034.1121) for more information.

2.2.4 AC Adapter

The AC Adapter can be used to power the System where batteries alone would not be appropriate. Refer to the

AC Adapter Installation Guide (Document # 7037.0320) for more information. (Item/Order # 701107, “AC-

Power Supply Multi-Adapter”)

2.2.5 Battery Box

The Battery Box can serve as the secondary power source to the LA GARD System. Refer to the Battery Box

Installation Guide (Document #7035.0421) for more information. The Battery Box is not UL evaluated.

(Item/Order # 704055, “Battery Box”)

2.2.6 Alarm Box

The Alarm Box is a hard-wired external alarm device. If used, the Alarm Box must be plugged into the BAT port

of Lock #1. The Alarm Box allows for a remote disable input that can block the open command to the lock if

dormakaba USA Inc. System User Guide 7040.1121 Rev E2 10/22 | 10

asserted. Refer to the Alarm Box Installation Guide (Document #7036.0320) for more information. The Alarm

Box is not UL evaluated. (Item/Order # 704045, “Alarm Box”)

2.2.7 Reset Box

The Reset Box offers the capability to remove users and reset the Master Combination. To reset the lock, the

lock must be disconnected from any power source (AC Power or Battery) and powered from the Reset Box only.

The Reset Box must be connected to the BAT port on the back of the LA GARD safe lock. The Reset Box has a

green LED that will light when the reset function is performed. If a lock is already reset, applying the Reset Box

will not light the LED.

The Reset Box will only work in conjunction with LA GARD safe locks with a BAT port (will not work with older

model LG BASIC Series locks). Refer to the Reset Box User Guide (Document #7039.0521) for more

information. The Reset Box is not UL evaluated. (Item/Order # 704065, “Reset Box”)

2.2.8 Fob

The fob is used as a secondary Bluetooth® credential to user’s combination. The fob can be enrolled at the

Model 705 Keypad and assigned to a user.

For UL 2058 compliance, the fob credential was not evaluated by UL. However, if a fob credential is employed,

it’s required to be accompanied by a user combination to open a lock. The fob cannot be used as sole means to

operate and open the lock. (Item/Order # 890165, “FOB (Bluetooth Enabled Credential)”)

2.2.9 Power Considerations

The system common power across all components. As long as 9V DC power is supplied to the system, the

system will work as intended. It is unnecessary to apply multiple sources of power to some or all components.

Some considerations to follow:

• The standard-profile Keypad models require two 9V batteries can be inserted into the tray.

• The low-profile Keypad models require a Battery Box or Power Adapter accessory is required for power.

These keypads include an emergency battery connection to apply power from outside of the safe

container.

• A LA GARD 700 Series Battery Box accessory is available to be attached inside the secure container to

grant power to the system.

• A LA GARD 700 Series Alarm Box can be connected to the primary lock to provide power to the system.

This Alarm Box must be physically located in the secure side of the container.

• A LA GARD 700 Series AC/DC Power Adapter accessory can be used to apply line power to the system.

The power adapter can be connected to any lock’s BAT port in a multi-lock configuration.

• In multi-lock installations while using a Multiplexer, it is strongly recommended that the AC/DC Power

Adapter be used.

• When resetting a lock via the LA GARD Series 700 Reset Box, a 9V battery must be inserted into the Reset

Box to apply power for the short duration usage.

dormakaba USA Inc. System User Guide 7040.1121 Rev E2 10/22 | 11

2.3 Getting Started

This section outlines typical use of a System with a single or multi-lock/single or multi-user setup with

references to various sections found through this document.

Follow these steps to get started implementing a System:

1. Identifying System Requirements

a. Identify Required System Components – Review Section 2.2 “System Components” for

installation procedures regarding each component of a System. For single lock Systems, the use

of a Multiplexer is not required.

b. Identify Required System Functions – Review Section 3.3 “System Functions” for an overview of

how each user is authorized to use the system.

c. Identify Required User Types and Privileges – Read Section 3.4.1 “Lock User Types” and 3.4.2

“User Privileges” for an overview how each user is authorized to use the system.

2. Configure the System

a. Install (Electronically Pair) Lock(s) – Read Section 3.5 “Install (Electronically Pair) a Lock and

Keypad” for instructions on performing this step.

b. Add Users – Read Section 3.4.3 “Assigning User IDs and Privileges” for instructions on adding all

non-Master users.

c. Change Master User Combination – Read Section 3.7 ”Change Combination” for instructions in

changing the Combination for the Master User.

3. Customize the System

a. For Keypad Models 702-705, Set Date and Time – Read Section 3.9 “Change Time/Date/DST”

for instructions on setting or re-setting the Time.

b. Configure other System Functions – Instructions for configuring custom options are provided in

Section 3.3 “System Functions”.

3 How to Use the System

This section outlines how to use the installed system and how to execute specified functions. Please note that

your installation may not include everything outlined in this section.

3.1 Keypad Model Definitions

Table 1 – Keypad Model Definitions

Model 701 Model 702,

702D

Model 703,

703B

Model 704,

704B Model 705

OLED Display

Keypad

(1.28”, Monochrome,

128 x 64)

No 702D only Yes Yes Yes

Compatible

Lock Types

⸸(Swing Bolt, Dead

Bolt, Spring Bolt)

⸸All ⸸All ⸸All ⸸All ⸸All

dormakaba USA Inc. System User Guide 7040.1121 Rev E2 10/22 | 12

Model 701 Model 702,

702D

Model 703,

703B

Model 704,

704B Model 705

Max. # of Total

Users

(includes Master and

Manager users)

3 30 30 50 100

Max. # of

Master Users 1 1 1 1 1

Max. # of

Managers 1 1 1 2 2

# of Locks 1 1 2 5 5

Dual-User

Mode No Yes Yes Yes Yes

Reset Function Yes Yes Yes Yes Yes

Time Delay No 0-99 Min. 0-99 Min. 0-99 Min. 0-99 Min.

Confirmation

Window No 1-60 Min. 1-60 Min. 1-60 Min. 1-60 Min.

Time Delay

Override

(TDO)

No Yes Yes Yes Yes

TDO with BLE

Key fob No No No No Yes

Programmable

at Keypad Yes 702D Only Yes Yes Yes

Programmable

by PC No Yes Yes Yes Yes

Audit Events No 500 500 2000 6000

View Audit

Trail No 702D Only Yes Yes Yes

Downloadable

Audit Trail No Yes Yes Yes Yes

dormakaba USA Inc. System User Guide 7040.1121 Rev E2 10/22 | 13

Model 701 Model 702,

702D

Model 703,

703B

Model 704,

704B Model 705

Duress Alarm No Yes Yes Yes Yes

Combination

Length

11

(2id + 6-9)

11

(2id + 6-9)

11

(2id + 6-9)

11

(2id + 6-9)

11

(2id + 6-9)

Back Lit

Keypad No Yes Yes Yes Yes

Bolt Switch

Option* No Yes Yes Yes Yes

Wrong Try

Penalty Yes Yes Yes Yes Yes

Battery Power 2 x 9V 2 x 9V 2 x 9V 2 x 9V 2 x 9V

Low-Profile

Option No Yes Yes Yes No

AC Power

Option* Yes Yes Yes Yes Yes

VdS 2396 –

Class 2 Yes Yes Yes Yes No

UL 2058 – UL

Type 1 Yes Yes Yes Yes Yes

EN1300 – Level

B Yes Yes Yes Yes No

SBSC – 3880-

2015 Yes Yes Yes Yes No

CNPP q2p –

Level B/E Yes Yes Yes Yes No

Time Lock

Schedule No No No Yes Yes

Dual

Credential No No 703B only 704B only Yes

dormakaba USA Inc. System User Guide 7040.1121 Rev E2 10/22 | 14

Model 701 Model 702,

702D

Model 703,

703B

Model 704,

704B Model 705

Warranty 2yr from DoM 2yr from DoM 2yr from DoM 2yr from DoM 2yr from DoM

Extended

Warranty* Yes Yes Yes Yes Yes

Updatable

Firmware Yes Yes Yes Yes Yes

*Sold separately

3.2 Keypad – Layout, Usage, and Settings

3.2.1 Keypad Layout & General Usage

Below is a list of buttons and their functions on the Keypad:

• Number Pad – Can be used for entering User combinations, # commands (for non-Display Keypads) and

specific optional functions on screen (for Display Keypads)

• Pound Key (#) – Is used to return to a previous screen, or to wake up the Keypad without entering a

number

• Up and Down Arrows (˄˅) – Navigate through options with these (for Display Keypads)

• Return Key (←) – Confirms a selection or complete a command sequence

3.2.2 Using a Display Keypad – Menu Settings

To enter the Main Menu, press any non-numeric button followed by your user credentials.

Below is a table outlining each Menu Setting and sub-setting within the Keypad display interface. Note that the

menu available changes based on the User Role and/or User Privileges.

Table 2 – Menu Settings (Display Keypad)

Open Lock

Allows the User to open a lock.

Change combo New Combo

Allows the User to change their combination.

Time/Date Time Format

Choose between a 12 and 24HR time format.

Date Format

Change the date format.

Set Time Date

Change the time and date.

Observe DST

Select Enable/Disable to observe Daylight Saving

Time (DST).

Time Lock Assign Access

Designate a lock as 24/7 or assign one of two

schedules.

dormakaba USA Inc. System User Guide 7040.1121 Rev E2 10/22 | 15

View Access 1

View the access of schedule #1.

View Access 2

View the access of schedule #2.

View Holiday

View the assigned holidays.

Audits*

Displays transactional data from a lock.

PC Link*

Connects the Keypad to a PC running the LA GARD

software client.

Users Add

Add a User based on their User ID.

Edit

Edit a User based on their User ID.

Delete

Delete a User based on their User ID.

System Sys Info Keypad Displays Battery Status, Firmware version, Model

and Serial #s.

Lock Shows firmware versions, serial numbers, port & Lock

# and Open Count.

Backlight

Toggle the Backlight On and Off.

Buzzer

Toggle the Buzzer sound On and Off.

TD Cnt Mode

Set counting period to count up, down or not show

time in the periods.

Combination Combo

Length Determines the length of a combination.

Force

Change

Determines whether or not new Users will have to

change their combination after initial login (choose

Yes/No)

User Mode

Choose between Single, Dual and Dual + Mgr.

Cred Mode

Choose between Single, Dual and Dual + Mgr.

Duress Mode*

Enables/Disables Duress Mode (Silent Alarm).

Input Signal Disable

Open

Configures the Input Signal for Remote Disable

function.

Dly

Override

Configures the Input Signal for Time Delay Override

function.

Dual

Override

Configures the Input Signal for Dual User Override

function

dormakaba USA Inc. System User Guide 7040.1121 Rev E2 10/22 | 16

Locks

Choose between Install, Uninstall, TL Schedule, Time

Delay configuration times, Time Delay Override

allowed and Reset.

FW Update

Enables a firmware update when connected to a PC

running the LA GARD software client.

*Not evaluated by UL

3.2.3 Using a Non-Display Keypad - # Commands

Below is a table outlining each # Command and their function for non-Display Keypads. For more details,

please refer to Appendix C (contains 701 model # commands) and Appendix D (contains 702 model #

commands).

Table 3 – # Commands (non-Display Keypad)

3.3 System Functions

The System menu allows the User to view and change various aspects, such as Combination length, Buzzer and

Backlight, amongst other options. Below is a table that outlines Buzzer, LED, and Screen Messages in response

to certain events.

Table 4 – Buzzer, LED, and Screen Message(s)

Event Buzzer LED Screen Message(s) (Display Only)

System wakeup Short high beep Short green flash N/A

Set Combo Length #11 Open PC Link #30 Delete User #56

Set User Mode #12 Reinstall Keypad #32 Reset User Combo #57

Set Duress

(Silent Alarm) #14 Set Backlight On/Off #40 Observe DST #63

Input Signal

Configure #16 Set Buzzer On/Off #41 Set Time/Date #65

Force Combination

Change On/Off #17 Add User #50 Set Time Delay and

Open Windows Values #72

Install Lock #22 Change Own Combo #52 Set TDO Allowance #73

Uninstall Lock #23 User Enable/Disable #54 Cancel Time Delay #74

Reset Keypad #25 Set User Lock Privileges #55 Enable FW Update #99

dormakaba USA Inc. System User Guide 7040.1121 Rev E2 10/22 | 17

Event Buzzer LED Screen Message(s) (Display Only)

Key press Short beep Short green or red flash High beep + Green flash = Valid Key

Low Beep + Red flash = Invalid Key

Valid command

response 3 short high beeps 3 short green flashes Success

Invalid command

response 3 short low beeps 3 short red flashes Invalid Message

Wrong Try Penalty 2 short low beeps

- every 10 seconds

2 short red flashes –

every 10 seconds Wrong Try Penalty

Wrong Try Penalty

ends 2 short high beeps 2 short green flashes

Time Delay 1 low beep – every

10 seconds

1 red flash – every 10

seconds Time Delay

Confirm window 1 high beep –

every 10 seconds

1 green flash – every 10

seconds Confirmation Window

Low Battery 2 low beeps 2 red flashes Low Battery

Critical Low Battery 3 long low beeps 3 long red flashes Critical Low Battery

Master Reset 3 short high beeps 3 short green flashes Reset Success

Power On – No lock

connected

5 medium to low

beeps 5 medium red flashes No Lock Found

Turn Power Off and Connect

Power On – Bad

configuration

5 medium to low

beeps 5 medium red flashes Bad Config

Power On/Wake Up –

Lock Connected but

Not Installed

1 medium low

beep Solid red LED Lock Detected

Power On – Keypad

not compatible 1 long low beep Continuous alternate

flashing red and green

Wrong Keypad Model Cannot

Install

Master reset 3 short high

beeps 3 short green flashes Reset Success

3.3.1 System Info (Display Only)

The System Info screen provides information related to the Keypad and safe locks connected to the System,

including Firmware version and Model number. Note: This information is only available to authorized users.

Follow these steps to navigate through the System Info menu:

dormakaba USA Inc. System User Guide 7040.1121 Rev E2 10/22 | 18

1. Enter and Authorized User ID and Combination.

2. Navigate through the Main Menu and select “System”.

3. Select “Sys Info” from the sub-menu.

4. Select between “Keypad” or “Lock”.

5. If “Keypad” is selected, the following information is available on screen:

• “Batt Status” – Displays battery level with a percentage

• “FW version” – Shows the current firmware version on the Keypad

• “Model” – Displays the Model # of the Keypad

• “S/N Part 1” and “S/N Part 2” – Shows the serial number of the Keypad (divided between two

screens)

6. If “Lock” is selected, the following information is available on screen:

• “FW version” – Displays the current firmware version on the safe lock

• “S/N Part 1” and “S/N Part 2” – Shows the serial number of the safe lock (divided between two

screens)

• “Port | Lock” – Represents the Port and Lock #s

• “Open Count” – Shows how many times the safe lock was opened

3.3.2 Backlight Mode

The Backlight illuminates whenever a key is pressed on the Keypad. By default, the Backlight setting is Off to

conserve battery power (if applicable). Note: This function is not available on the 701 series Keypad.

3.3.2.1 Backlight Mode – Display Keypad

Follow these steps to toggle the Backlight Mode On and Off on a Display Keypad:

1. Enter an Authorized User ID and Combination.

2. Navigate through the Main Menu and select “System”.

3. Select “Backlight” from the sub-menu.

4. Select between “On” and “Off” to Enable/Disable Backlight Mode.

5. “Success Mode updated” will appear on screen and the Keypad will beep three times and flash a green

LED once complete.

3.3.2.2 Backlight Mode – 702 Keypad (Non-Display)

Follow these steps to toggle the Backlight Mode On and Off on a 702 non-Display Keypad:

1. Using the Keypad, input #40 + Authorized User ID and Combination + Off (0) or On (1) + <return key> (←).

2. The Keypad will beep three times and flash a green LED once complete.

3.3.3 Buzzer Mode

The Buzzer provides sound to signal specific functional outcomes. The Buzzer Mode is active (on) by default. It

is recommended that the Buzzer is left on for Non-Display Keypads.

3.3.3.1 Buzzer Mode – Display Keypad

Follow these steps to toggle the Buzzer Mode On and Off on a Display Keypad:

1. Enter an Authorized User ID and Combination.

2. Navigate through the Main Menu and select “System”.

3. Select Buzzer from the sub-menu.

La page charge ...

Dormakaba LA GARD 700 Series Mode d'emploi

Dormakaba LA GARD 700 Series Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents