Sony ke-42ts2 Manuel utilisateur

4-094-602-

11

(1)

Flat Panel Colour TV

KE-32TS2E

KE-42TS2E

Operating Instructions

Bedienungsanleitung

Manual de instrucciones

Mode d’emploi

GB

DE

ES

FR

2

NOTICE FOR CUSTOMERS IN THE UNITED KINGDOM

A moulded plug complying with BS1363 is fitted to this equipment for your safety and

convenience.

Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or

BSI to BS 1362 (i.e. marked with

2

or

@

) must be used.

When an alternative type of plug is used it should be fitted with a 5 AMP FUSE, otherwise the

circuit should be protected by a 5 AMP FUSE at the distribution board.

If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse

cover after you change the fuse. Never use the plug without the fuse cover. If you should lose

the fuse cover, please contact your nearest Sony service station.

How to replace the fuse

Open the fuse compartment with a blade screwdriver, and replace the fuse.

•

IMPORTANT

If the plug supplied is not suitable for the socket outlets in your home, it should be cut off and

an appropriate plug fitted in accordance with the following instructions:

The wires in this mains lead are coloured in accordance with the following code:

Blue Neutral

Brown Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the

coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured blue must be connected to the terminal which is marked with the

letter N or coloured black. The wire which is coloured brown must be connected to the

terminal which is marked with the letter L or coloured red. Do not connect either wire to the

earth terminal in the plug which is marked by the letter E or by the safety earth symbol

Y

or

coloured green or green and yellow.

WARNING

• To prevent the risk of electric shock, do not insert the plug cut off from the mains lead into

a socket outlet. This plug cannot be used and should be destroyed.

• To prevent the risk of fire or electric shock, do not expose the unit to rain or moisture.

• Dangerously high voltages are present inside the set. Do not open the cabinet. Refer servicing

to qualified personnel only.

3

Table of Contents

GB

Introduction

Thank you for choosing this Sony Flat Panel Colour Television.

Before operating the TV, please read this manual thoroughly and retain it for future

reference.

Symbols used in the manual

Table of Contents

Notice for Customers in the United Kingdom ....................................................................................2

Introduction..............................................................................................................................................3

Safety Information ...................................................................................................................................4

Additional Safety Information ..............................................................................................................5

Checking the Accessories Supplied ......................................................................................................5

Overview

Overview of TV Buttons .........................................................................................................................6

Overview of Remote Control Buttons ..................................................................................................7

Installation

Inserting Batteries into the Remote Control ........................................................................................8

Connecting the AC Cable, Aerial and VCR .........................................................................................8

Preventing the TV from Falling Down .................................................................................................9

First Time Operation

Switching On the TV and Automatically Tuning .............................................................................11

Menu System

Introducing and Using the Menu System ..........................................................................................13

Picture Adjustment................................................................................................................................13

Sound Adjustment.................................................................................................................................15

Screen Control........................................................................................................................................16

Features ...................................................................................................................................................19

Set Up ......................................................................................................................................................21

Timer........................................................................................................................................................24

Unit Status...............................................................................................................................................26

Teletext

Teletext ....................................................................................................................................................27

Additional Information

Connecting Optional Equipment ........................................................................................................28

Using Optional Equipment ..................................................................................................................30

Remote Control Configuration for VCR/DVD .................................................................................31

Specifications..........................................................................................................................................32

Troubleshooting.....................................................................................................................................33

Television Channel Number Guide for United Kingdom...............................................................35

......Important information.

......Information on a feature.

1,2 ........Sequence of instructions.

......Shaded buttons on the remote

control show you the buttons you

have to press to follow the sequence

of instructions.

...........Informs you of the result of

instructions.

OK

4

Safety Information

Do not open the cabinet and the rear

cover of the TV. Refer to qualiﬁed

service personnel only.

To prevent ﬁre or shock

hazard, do not expose the TV

to rain or moisture.

For your own safety, do not touch

any part of the TV, power lead or

aerial lead during lightning

storms.

Do not cover the ventilation

openings of the TV. For ventilation,

leave a space of at least 10cm all

around the set.

Never place the TV in hot, humid

or excessively dusty places. Do

not install the TV where it may be

exposed to mechanical vibrations.

To prevent ﬁre, keep inﬂammable

objects or naked lights (eg

candles) away from the TV.

Pull out the power lead by the

plug. Do not pull on the power

lead itself.

Take care not to place heavy

objects on the power lead as this

could result in damage.

We recommend you wind any

excess lead around the holders

provided on the rear of the TV.

Place the TV on a secure stable

stand. Do not allow children to

climb on to it. Do not place the TV

on its side or face up.

Do not cover the ventilation

openings of the TV with items

such as curtains or newspapers

etc.

Safety Information

Never push objects of any kind into

the set as this could result in a ﬁre

or electric shock. Never spill liquid

of any kind on the set. If any liquid

or solid object does fall through, do

not operate the TV. Have it checked

immediately by qualiﬁed

personnel.

For environmental and safety

reasons, it is recommended that

the TV set is not left in standby

mode when not in use. Disconnect

from the mains.

This set is to operate on a 220-

240V AC supply only. Take care

not to connect too many

appliances to the same power

socket as this could result in ﬁre

or electric shock.

Unplug the power lead before

moving the TV. Avoid uneven

surfaces, quick steps or excessive

force. If the set has been dropped

or damaged, have it checked

immediately by qualiﬁed service

personnel.

Clean the screen and cabinet with a

soft, lightly dampened cloth. Do

not use any type of abrasive pad,

alkaline cleaner, scouring powder

or solvent, such as alcohol or

benzine, or antistatic spray. As a

safety precaution, unplug the TV

before cleaning it.

5

Safety Information

GB

Additional Safety Information

• This set should only be moved by two or

more people. If the set needs to be

transported, it should be protected to insure

that it is not subject to shock, vibration or

excessive force.

• The slots and openings in the cabinet and in

the back and bottom are provided for the

necessary ventilation. To ensure reliable

operation of the set, and to protect it from

overheating, these slots and openings must

never be blocked or covered.

• After transporting the set directly from a cold

to a warm location, or if the room

temperature has changed suddenly, pictures

may be blurred or show poor colour over

portions of the picture. This is because

moisture has condensed on the mirrors or

lenses inside the set. Let the moisture

evaporate before using the set.

• To obtain a clear picture, do not expose the

screen to direct illumination or direct

sunlight. If possible, use spot lighting

directed down from the ceiling.

• The screen of this display unit has an anti-

reflection screen coating. To avoid screen

degradation, follow the points mentioned

below. Do not push on or scratch with hard

objects, or throw anything at the screen. The

screen may be damaged.

– Be sure to unplug the mains lead connected

to the media receiver unit from the mains

before cleaning.

– Do not touch the display panel after

operating continuously for along period as

the display panel becomes hot.

– The screen of this display unit has an anti-

reflection screen coating. We recommend

that the screen surface is touched as little as

possible.

– Clean the screen with the supplied cleaning

cloth or a soft cloth lightly moistened with

a mild detergent solution.

– Never use any type of abrasive pad,

scouring powder, or solvent, such as

alcohol or benzine. This type of contact may

result in damage to the screen surface.

• The TV set is not disconnected from the

mains when the switch is in Off position. To

disconnect completely the set, pull the plug

from the mains.

•

Note on use in highlands

When used at an altitude of greater than 1900

m or 6248 feet (air pressure less than 800hPa),

this Plasma Display Panel may generate a

low buzzing sound as a result of the

difference between the interior and exterior

air pressure of the panels. This is not

considered a defect and is not covered by the

Sony Warranty. This buzzing sound is an

inherent characteristic of any Plasma display

Panel.

Corrosion

Use of this set near the seashore may subject the

set to excessive salt, corrosion and internal

damage and result in deterioration of the set’s

performance. If the set will be subjected to any

of these conditions, steps should be taken to

reduce the humidity and temperature of the

area where the set is located.

On image retention

• If the following images are displayed for an

extended period time, image retention

(afterimage) in areas of the screen may result

due to the characteristics of the Plasma

Display Panel.

– Black bars at the top and bottom that

appear with a wide video source (Letterbox

picture).

– Black bars to the left and right that appear

with a 4:3 video source (conventional TV

broadcasts).

– Video game sources

– PC images

– DVD on-screen menu displays

– On-screen menus, channel numbers, etc., of

connected equipment such as Set top box,

Cable modem, VCR, etc.

The risk of this is higher if the set is in “Live”

mode or has a high contrast setting. This

image cannot be removed once burnt onto

the screen. To avoid the risk of image

retention do not leave the TV set operating on

such a picture, or programme for a long time,

use the “Screen Saver” function or lower the

contrast setting. Repeated extended daily

usage of the same image, or programme can

also result in this occurrence. IMAGE

RETENTION IS NOT COVERED BY THE

SONY WARRANTY.

• To reduce image retention, this TV set has the

“Screen Saver” function. The default setting

of the “Orbit” function in “Screen Saver” is

“On.”

• The “Screen Saver” function prevents and

reduces image retention.

• With extensive use of this TV set in 4:3 mode,

the 4:3 screen area might become darker

within a 16:9 panel. To avoid this problem,

the “Smart” picture mode should be used.

Checking the Accessories Supplied

See page 32.

6

Overview

Overview of TV Buttons

(input select) button

2 (volume) +/– button

PROG (channel) +/– button

Power switch

/ (standby/sleep)

indicator

Remote control sensor

i Headphone jack

Use headphones with L type connector.

If you connect headphones, the TV speakers

will automatically be muted.

7

Overview

GB

Overview of Remote Control Buttons

q;

Media Selector:

With this remote control you can operate not only this TV but also the main functions

of your VCR or DVD.

Switch on the device you want to operate and next press this button repeatedly to select the VCR, TV or

DVD. A green light will be lit momentarily.

qa

Selecting channels:

Press these buttons to select the next or previous channel.

qs

Muting the Sound:

Press this button to mute TV sound. Press again to restore the sound.

qd

Adjusting TV volume:

Press these buttons to adjust the volume of the TV.

qf

Displaying the menu system:

Press this button to display the menu on the TV screen. Press again to

remove the menu display from the TV screen.

qg

Selecting TV mode:

Press this button to switch off teletext or video input.

qh

Selecting Sound effect:

Press this button repeatedly to change the sound effect.

qj

Selecting Picture mode:

Press this button repeatedly to change the picture mode.

qk

Displaying on-screen information:

Press this button to display all on-screen indications. Press again

to cancel.

ql

VCR or DVD on/off:

Press this button to switch your VCR or DVD on or off.

An initial set up is required to synchronise this remote control to your VCR or DVD. It will depend on

the Brand of those products. For more details, refer to chapter “Remote Control Configuration for

VCR/DVD” on page 31.

Besides TV functions, all coloured buttons as well as green symbols are also used for

Teletext operations. For more details, please refer to the “Teletext” section on page 27 of this instruction

manual.

1

To Temporarily Switch Off TV:

Press this button to temporarily switch

off the TV (the / (standby/sleep) indicator

on TV lights up). Press

again to switch on the TV from standby mode.

To save energy we recommend switching off completely when TV is not in use.

After a certain period without a signal and without any button

being pressed, the TV switches automatically into standby mode

(Auto Shutoff, page 25).

2

Selecting input source:

Press this button repeatedly until the desired

input symbol of the source appears on the TV screen.

3

Selecting channels:

If Media Selector is switched on TV or VCR, press

this button to select channels.

For double-digit programme numbers, enter the second digit within 2.5

seconds.

4

a)If Media Selector button is switched on TV:

Press this button to

watch the last channel selected (watched for at least 5 seconds).

b)If Media Selector button is switched on VCR:

For Sony’s VCR

double-digit programme numbers, e.g. 23, press -/- - first and then the

buttons 2 and 3.

5 This button only works in Teletext mode.

6 Selecting screen format: Press this button repeatedly to change the

format of the screen. For more details, refer to chapter “Screen Control” on

page 16.

7 Selecting Teletext: Press this button to switch on Teletext.

8 a)If Media Selector is switched on TV:

When MENU is switched on, use these buttons to operate the menu

system. For details refer to “Introducing and Using the Menu System”

on page 13.

b)If Media Selector button is switched on VCR or DVD: Using

these buttons you can control the main functions of your VCR or DVD.

9 Recording button: If Media Selector is switched to VCR, press this

button to record programmes.

/

TVVIDEO

OK

DVDVCR

123

456

789

0

PROG

TV

MENU REC

1

2

4

5

3

6

!ª

!•

!§

7

9

!º

!¡

8

!∞

!¢

!£

!™

!¶

8

Installation

Inserting Batteries into the Remote Control

Connecting the Aerial and VCR

Make sure you insert the supplied batteries using the correct polarity.

Always remember to dispose of used batteries in an environmentally friendly way.

• Use the supplied AC cable (Type BF).

• Use the supplied coaxial cable for aerial connection.

• Other connecting cables are not supplied.

For more details of VCR connection, please refer

to the section “Connecting Optional Equipment”

on page 28 of this instruction manual.

L/G/S/IR/D/D/D

L/G/S/I

(SMARTLINK)

R/D/D/D Y/G PB/CB/BPR/CR/RHD VD

L/G/S/I

R/D/D/D

CTRL S

(W/G/W/G)

AC IN

L/G/S/IR/D/D/D

L/G/S/I

(SMARTLINK)

R/D/D/D Y/G PB/CB/BPR/CR/RHD VD

L/G/S/I

R/D/D/D

CTRL S

(W/G/W/G)

AC IN

OUT IN

or

Connect the supplied

cosxial cable.

VCR

Connect the supplied AC cable

(Type BF, with safety earth).

Scart lead is optional.

9

Installation

GB

Preventing the TV from Falling Down

Attach the supplied bracket to the rear of the TV, and pass a sturdy cord or chain through it to

attach it to a wall or pillar. Consult your dealer when attaching the bracket, since the screws for

the bracket also hold the rear cabinet in a place.

1 Remove one of the screws attached at the rear

of the TV.

Do not remove both screws at the same

time as these screws secure the rear

cabinet. Never use the TV with the

screws removed.

2 Attach the supplied bracket with the screw.

Be sure to use the screw that attaches the

rear cabinet. A different screw may

damage the TV and result in electric

shock.

3 Repeat steps 1 and 2 to attach the other bracket.

4 Attach a sturdy cord or chain securely to each

bracket on the rear of the TV.

Bracket

(supplied)

Attach the

sturdy cord

or chain (not

supplied)

securely.

continued...

10

Installation

5 Fix the cord or chain to a wall or pillar.

Screw a hook (not supplied) to the wall or pillar

securely.

Side view Rear view

11

First Time Operation

GB

Switching On the TV and Automatically Tuning

The first time you switch on your TV, a sequence of menu screens appear on the TV

enabling you to: 1) choose the language of the menu screen, 2) choose the country in which

you wish to operate the TV, 3) search and store all available channels (TV Broadcast) and

4) change the order in which the channels (TV Broadcast) appear on the screen.

However, if you need to change any of these settings at a later date, you can do that by

selecting the appropriate option in the (Set Up) menu.

1 Connect the TV plug to the mains socket (220-240V

AC, 50Hz)

The first time that the TV set is connected, it is usually

turned on. If the TV is off, press the Power switch

on the TV set to turn on the TV.

The first time you switch on the TV, a Language menu

displays automatically on the TV screen.

2 Press the or button on the remote control to

select the language, then press the OK button to

confirm your selection.

From now on all the menus will appear in the selected

language.

3 The Country menu appears automatically on the TV

screen.

Press the or button to select the country in

which you will operate the TV set, then press the OK

button to confirm your selection.

• If the country in which you want to use the TV

set does not appear in the list, select “-”

instead of a country.

• In case of changing the country selection

(including “-”), the next procedure of Auto

Tuning always should be done after that.

4 The Auto Tuning menu appears on the screen.

Press the OK button to select Yes.

Language

Engl

Españo l

Italiano

Françai s

Por t uguês

Deutsch

Neder l ands

ish

Select language

, to select, press

to set

OK

Count r y

Select country

—

United Kingdom

France

España

Italia

Portugal

Nederland

Deutschland

, to select, press

to set

OK

Do you

Yes

No

automatic tuning?

want to start

continued...

12

First Time Operation

5 The TV starts to automatically search and store all

available broadcast channels for you.

This procedure could take some minutes. Please

be patient and do not press any buttons,

otherwise the automatic tuning will not be

completed.

If no channels were found during the auto

tuning process then a new menu appears

automatically on the screen asking you to

connect the aerial. Please connect the aerial (see

page 8) and press OK. The auto tuning process

will start again.

6 After all available channels are captured and

stored, the Programme Sorting menu appears

automatically on the screen enabling you to

change the order in which the channels appear

on the screen.

a) If you wish to keep the broadcast channels in the

tuned order, go to step 7.

b) If you wish to store the channels in a different

order:

1 Press the or button to select the

programme number with the channel (TV

Broadcast) you wish to rearrange, then press

the button.

2 Press the or button to select the new

programme number position for your selected

channel (TV Broadcast), then press .

3 Repeat steps b)1 and b)2 if you wish to change

the order of the other channels.

7 Press the MENU button to remove the menu from the

screen.

Your TV is now ready for use

OK

Auto Tuning

Conf

Programme

Searching. . .

:

Channel :

System :

01

C21

I

No channel found.

Conf i rm

Please connect aer i

al

OK

Programme Sorting

01

02

03

04

05

06

07

08

TVE

TVE2

TV3

C33

C27

C58

S02

S06

Select

Exit :

channel

MENU

, to select,

,to set

OK

Programme Sorting

01

02

03

04

05

06

07

08

TVE

TVE2

TV3

C33

C27

01 TVE

C58

S02

S06

Select

Exit :

new position

MENU

, to select, press to return

OK

MENU

13

Menu System

GB

Introducing and Using the Menu System

Picture Adjustment

Your TV uses an on-screen menu system to guide you through the operations. Use the

following buttons on the Remote Control to operate the menu system:

1Press the MENU button to switch the first level menu on.

2 • To highlight the desired menu or option, press or .

• To enter to the selected menu or option, press .

• To return to the last menu or option, press .

• To alter settings of your selected option, press //or.

• To confirm and store your selection, press OK.

3 Press the MENU button to remove the menu from the screen.

The “Picture Adjustment” menu

allows you to alter the picture

adjustments.

To do this:

After selecting the item you want to

alter press , then press

repeatedly / / or to

adjust it and finally press OK to store

the new adjustment.

This menu also allows you to

customise the picture quality for the

“Movie,” “Personal1,” and

“Personal2” modes based on the

programme you are watching.

Mode Live (for enhanced picture contrast and sharpness).

Standard (for a picture with contrast to suit your room’s lighting

conditions.).

Movie (for a finely detailed picture).

Personal1 (for your own custom settings).

Personal2 (for your own custom settings).

Contrast Press / to reduce picture contrast

Press / to enhance picture contrast

Brightness Press / to darken the picture

Press / to brighten the picture

MENU

OK

MENU

Con t

Mode

rast

Pict

Brightness

Colour

Sharpness

NR

Dynamic

Low

Personal1

On

:

Picture Adjustment

,,,to to

enter adj . menu

select

OK

Colour

Tone

Cool

:

Con t

Mode

rast

Pict

Brightness

Colour

Sharpness

NR

Dynamic

Low

Personal1

On

:

Picture Adjustment

,,,to to

set

select

OK

Colour

Tone

Cool

:

continued...

14

Menu System

Colour Press / to decrease colour intensity.

Press / to increase colour intensity.

Colour cannot be adjusted for the RGB input.

Sharpness Press / to soften the picture.

Press / to sharpen the picture.

NR (Noise

Reduction)

Off/Low/Mid/High

Select to reduce the noise level of all connected equipment. It is

most effective on the signal from the VHF/UHF jack.

You cannot adjust NR (Noise Reduction) for equipment connected to the RGB

input.

Dynamic Pict On/Off

Select to enhance the picture contrast.

Colour Tone Cool/Normal/Warm/User1/User2/User3

Select to give bright colours a red tint (Setting is variable from Cool

to Warm).

Select User1, User2, or User3 to customise the Colour Tone by

adjusting Red Gain, Green Gain, and Blue Gain (tint), and store

them in memory.

Name Set: Select to name your personal settings. Press / /

/ to select the letter, then press OK. Finally press

// or to select the word “End” on the

screen and press OK to store.

• To correct the letter, select on the screen to go

back and press OK.

• For a blank, select on the screen and press OK.

Colour Correct On/Off

Select to emphasise reds and blues.

Colour Correct cannot be adjusted for the RGB input.

Gamma Correct High/Mid/Low

Select to adjust the balance between bright and dark areas of the

picture.

Reset Cancel/OK

Select OK to reset the picture to the factory preset levels.

Each option cannot be adjusted when Mode is set to Live or Standard.

15

Menu System

GB

Sound Adjustment

The “Sound Adjustment” menu

allows you to alter the sound

adjustments.

To do this:

After selecting the item you want to

alter, press , then press repeatedly

// or to adjust it and

finally press OK to store the new

adjustment.

Effect Off (no effect).

Natural (enhances clarity, detail and presence of sound by using

“BBE High Definition Sound system”

*).

Dynamic (“BBE High Definition Sound system”* intensifies clarity

and presence of sound for better intelligibility and musical

realism).

TS (TruSurround**) (for surround sound (for example, DVD

software). It produces a virtual sound effect.)

* The “BBE High Definition Sound system” is manufactured by Sony

Corporation under license from BBE Sound, Inc. It is covered by U.S. Patent

No. 4,638,258 and No. 4,482,866. The word “BBE” and BBE Symbol are

trademarks of BBE sound.

** TruSurround and the symbol are trademarks of SRS Labs, Inc.

Trusurround technology is incorporated under license from SRS Labs, Inc.

Treble

Press / to decrease higher-pitched sounds.

Press / to increase higher-pitched sounds.

Bass

Press / to decrease lower-pitched sounds.

Press / to increase lower-pitched sounds.

Balance Press / to emphasise the left speaker.

Press / to emphasise the right speaker.

Dual Sound Mono/Stereo

For a stereo broadcast, select Stereo or Mono.

Mono/A/B

For a bilingual broadcast, select A for sound channel 1, B for sound

channel 2 or Mono for mono channel if available.

Auto Volume On/Off

Volume level of the channels will stay the same, independent of the

broadcast signal (e.g. in the case of advertisements).

Reset Cancel/OK

Select OK to reset the sound to the factory preset.

Con t

Mode

rast

Pict

Brightness

Colour

Sharpness

NR

Dynamic

Low

Personal1

On

:

Picture Adjustment

,,,to to

enter adj . menu

select

OK

Colour

Tone

Cool

:

T reble

Bass

Effect

Balance

AutoVolume

Dual

Reset

Off

Mono

:

Sound

Adjustment

,,,to to

enter adj . menu

select

OK

T reble

Bass

Balance

AutoVolume

Dual

Reset

Off

Mono

:

Sound

Adjustment

Effect

Off

:

,,,to to

set

select

OK

16

Menu System

Screen Contro

l

The “Screen Control” menu allows

you to alter the screen adjustments.

Auto Format The “Auto Format” option allows you to automatically change the

aspect ratio of the screen.

To do this:

After selecting the option, press . Then press or

to select

On (if you wish the TV set to automatically switch the screen

format according to the broadcast signal) or Off (if you wish to

keep your preference) and finally press OK to store.

Even if you have selected On or Off in the “Auto Format” option, you can

always modify the format of the screen by pressing repeatedly on the

remote control.

Screen Format The “Screen Format” option allows you to modify the format of the

screen.

To do this:

After selecting the option, press . Then press or to select

the desired screen format and finally press OK to store.

Smart: Imitation of wide screen effect

for 4:3 broadcast.

4:3: Conventional 4:3 picture size,

full picture information.

14:9: Compromise between 4:3 and

16:9 picture size.

Zoom: Wide screen format for

letterbox movies.

Wide: For 16:9 broadcast.

If parts of the top and bottom of the screen are cut off, press

or to adjust

the position of the image on the screen (e.g. to read subtitles).

Con t

Mode

rast

Pict

Brightness

Colour

Sharpness

NR

Dynamic

Low

Personal1

On

:

Picture Adjustment

,,,to to

enter adj . menu

select

OK

Colour

Tone

Cool

:

Screen

Screen Size

Adjust Pixel

Screen

Reset

Wide

:

Shift

Auto Format

Format

Zoom

On

:

Screen Control

S tandard

,,,to to

enter adj . menu

select

OK

Screen

Screen Size

Adjust Pixel

Screen

Reset

Wide

:

Shift

Format

Zoom

:

Screen Control

S tandard

Auto

On

:

,,,to to

set

select

OK

Zoom

14:9

Wide

4:3

Smart

17

Menu System

GB

Screen Zoom The “Screen Zoom” option allows you to enlarge the picture with

the centre position fixed (only when Screen Format is set to Wide).

To do this:

After selecting the option, press . Then press or to select

from Standard (normal size), x 2 (doubled), x 3 (tripled), or x 4

(quadrupled) and finally press OK to store.

Screen Zoom can be adjusted only when Screen Format is set to Wide.

Screen Size The “Screen Size” option allows you to adjust the size of the

picture for each Screen Format.

To do this:

1 After selecting the option, press .

2 Press / / or to adjust each option, then press OK

to store.

Press to enlarge the Screen Size vertically.

Press to shrink the Screen Size vertically.

Press to shrink the Screen Size horizontally.

Press to enlarge the Screen Size horizontally.

Screen Size cannot be adjusted horizontally when Screen Format is set to Smart.

Screen Shift The “Screen Shift” option allows you to adjust the position of the

picture for each Screen Format.

To do this:

1 After selecting the option, press .

2 Press / / or to adjust each option, then press OK

to store.

Press to move the screen up.

Press to move the screen down.

Press to move the screen to the left.

Press to move the screen to the right.

Screen Shift cannot be adjusted horizontally when Screen Format is set to Smart.

continued...

18

Menu System

Adjust Pixel The “Adjust Pixel” option allows you to adjust the picture from an

RGB piece of equipment.

To do this:

1 After selecting the option, press .

2 Press or to select the following option.

Auto Adjust:

Select OK to automatically make the best picture for the input

signal. Note that it may not be adjusted perfectly depending

on the input signal condition or picture pattern. In this case,

perform Auto Adjust again.

Dot phase:

Adjust between 00-63 when part of a displayed text or image

is not clear.

Total H Pixel (Total Horizontal Pixel):

Adjust when the whole picture is not clear as a whole.

Reset:

Reset to the factory settings.

Adjust Pixel is only available for the RGB input signal connected to 5

connector and the “AV5 Input”option is set to “RGB” in the “Features” menu.

Reset Cancel / OK

Select OK to reset “Screen Zoom”, “Screen Size” and “Screen Shift”

options to the factory preset

19

Menu System

GB

Features

The “Features” menu allows you to

alter various adjustments of this TV’s

features.

Power Saving The “Power Saving” option allows you to reduce the power

consumption of this TV.

To do this:

After selecting the option, press

. Then press or to select

Reduce and finally press OK to store.

• If you turn off the TV whilst the Power Saving mode is on, the mode stays on

next time you turn on the TV.

• If you select the “Movie,” “Personal1” or “Personal2” mode on the “Picture

Adjustment” menu (page 13), you can adjust the picture option even if the

Power Saving mode is set to on. Note that power consumption will still increase

if you increase the Contrast or Brightness.

TV Speakers The “TV Speakers” option allows you to control the sound output

of the TV’s speakers when using your audio system speakers.

To do this:

After selecting the option, press

. Then press or to select

Off and finally press OK to store. Sound of the TV is not output

through the TV’s speakers.

Screen Saver The “Screen Saver” option allows you to reduce image retention.

To do this:

1 After selecting the option, press

.

Move the picture position to reduce image retention.

Orbit: Select On to move the position. If you select On, set

Orbit Range and Orbit Cycle.

Orbit Range: Select the moving range from Large, Mid

(Middle), and Small.

Orbit Cycle: Select the moving time from 10sec, 30sec,

1min, and 5min.

2 Press OK to store.

Con t

Mode

rast

Pict

Brightness

Colour

Sharpness

NR

Dynamic

Low

Personal1

On

:

Picture Adjustment

,,,to to

enter adj . menu

select

OK

Colour

Tone

Cool

:

TV

Screen

AV3 Output

AV4 Input

AV5 Input

RGB Mode

Auto

DTV

V ideo

Component

:

AV3 Input

V ideo

:

Saving

Speakers

Saver

:

F eatures

StandardPower

On

:

,,,to to

enter adj . menu

select

OK

TV

Screen

AV3 Output

AV4 Input

AV5 Input

RGB Mode

Auto

DTV

V ideo

Component

:

AV3 Input

V ideo

:

Speakers

Saver

:

F eatures

On

Saving St andardP ower :

,,,to to

set

select

OK

continued...

20

Menu System

AV3 Output The “AV3 Output” option allows you to select the source to be

output from the Scart connector 3/ . You can record from

this Scart any signal coming from the TV or from external

equipment connected to the other Scart connectors.

If your VCR supports SmartLink, this procedure is not

necessary.

To do this:

After selecting the option, press . Then press or to select

the desired output signal: Auto, TV, AV1, AV2, or AV4.

• If you select Auto, the output signal will always be the

same one that is displayed on the screen.

• If you have connected a decoder to the Scart 3/ or

to a VCR connected to this Scart, please remember to

change back the “AV3 Output” to Auto for correct

unscrambling.

• When AV3 Output is set to Auto, the signal input through

the AV5 input and the RGB signal are not output from the

Scart connector 3/ .

AV3 Input/

AV4 Input/

AV5 Input

The “AV3 Input,”“AV4 Input,” and “AV5 Input” options allow

you to select which jack the TV receives the input signal from;

Video or S Video for AV3 Input and AV4 Input, and Component

or RGB for AV5 input.

To do this:

After selecting the option, press

. Then press or to select

the desired jack and finally press OK to store.

RGB Mode Select the “RGB Mode” option if equipment which outputs RGB

signal is connected to the Y/G, PB/CB/B, PR/CR/R jacks of the

5.

To do this:

After selecting the option, press . Then press or to select

the connected equipment:

DTV for a digital tuner with RGB signal, or Others for other RGB

equipment.

DTV is the digital broadcast format standardised in the

United States, and there are several signal formats, such as

480i, 575i, 480p, 575p, 720p, or 1080i.

S

La page charge ...

Sony ke-42ts2 Manuel utilisateur

Ce manuel convient également à

Sony ke-42ts2 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents