STIHL BT 130 Manuel utilisateur

{

STIHL BT 130

Instruction Manual

Notice d’emploi

G Instruction Manual

1 - 25

F Notice d’emploi

26 - 53

Original Instruction ManualPrinted on chlorine-free paper

Printing inks contain vegetable oils, paper can be recycled.

0458-429-8221-A. VA0.E16.

0000006501_006_GB

BT 130

English

1

{

with electronic systems.

Contents

Dear Customer,

Thank you for choosing a quality

engineered STIHL product.

It has been built using modern

production techniques and

comprehensive quality assurance.

Every effort has been made to ensure

your satisfaction and troublefree use of

the product.

Please contact your dealer or our sales

company if you have any queries

concerning this product.

Your

Dr. Nikolas Stihl

Guide to Using this Manual 2

Safety Precautions and Working

Techniques 2

Assembling the Unit 7

Adjusting the Throttle Cable 8

Fuel 8

Fueling 9

Auger Brake 10

Fitting the Auger 10

Starting / Stopping the Engine 11

Operating Instructions 13

Releasing a Trapped Auger 14

Replacing the Air Filter 14

Engine Management 15

Adjusting the Carburetor 15

Spark Plug 16

Engine Running Behavior 17

Lubricating the Gearbox 17

Storing the Machine 17

Inspections and Maintenance by

Dealer 18

Maintenance and Care 19

Main Parts 21

Specifications 22

Maintenance and Repairs 23

Disposal 23

STIHL Limited Emission Control

Warranty Statement 24

BT 130

English

2

Pictograms

The meanings of the pictograms

attached to the machine are explained in

this manual.

Depending on the model concerned, the

following pictograms may be attached to

your machine.

Symbols in text

WARNING

Warning where there is a risk of an

accident or personal injury or serious

damage to property.

NOTICE

Caution where there is a risk of

damaging the machine or its individual

components.

Engineering improvements

STIHL's philosophy is to continually

improve all of its products. For this

reason we may modify the design,

engineering and appearance of our

products periodically.

Therefore, some changes, modifications

and improvements may not be covered

in this manual.

Observe all applicable local safety

regulations, standards and ordinances.

If you have not used this type of power

tool before: Have your dealer or other

experienced user show you how to

operate your machine or attend a

special course in its operation.

Minors should never be allowed to use a

power tool.

Keep bystanders, especially children,

and animals away from the work area.

When the power tool is not in use, shut it

off so that it does not endanger others.

Secure it against unauthorized use.

The user is responsible for avoiding

injury to third parties or damage to their

property.

Guide to Using this Manual

Fuel tank; fuel mixture of

gasoline and engine oil

Operate manual fuel

pump

Auger brake

Safety Precautions and

Working Techniques

Special safety precau-

tions must be observed

when working with this

power tool because of its

high torque and the high

speed of the auger in cer-

tain applications, and

because the augers have

sharp edges.

It is important that you

read the instruction man-

ual before first use and

keep it in a safe place for

future reference. Non-

observance of the

instruction manual may

result in serious or even

fatal injury.

BT 130

English

3

Do not lend or rent your power tool

without the instruction manual. Be sure

that anyone using it understands the

information contained in this manual.

The use of noise emitting power tools

may be restricted to certain times by

national or local regulations.

To operate the power tool you must be

rested, in good physical condition and

mental health.

If you have any condition that might be

aggravated by strenuous work, check

with your doctor before operating a

power tool.

Persons with pacemakers only: The

ignition system of your power tool

produces an electromagnetic field of a

very low intensity. This field may

interfere with some pacemakers. STIHL

recommends that persons with

pacemakers consult their physician and

the pacemaker manufacturer to reduce

any health risk.

Do not operate the power tool if you are

under the influence of any substance

(drugs, alcohol) which might impair

vision, dexterity or judgment.

Use your power tool only for drilling

holes in soil and wood – depending on

the drilling tool mounted. Select drilling

axis so that the auger brake lever is

always in a position to be activated by

the operator's thigh.

Do not use your power tool for any other

purpose.

Before drilling, make sure there are no

buried power cables or supply pipes in

the work area (e.g. for gas, water,

electricity):

– Contact your local utility company

for information on cable and pipe

locations.

– Where necessary, confirm actual

location with cable detectors and/or

by carefully dug trenches.

Only use drilling tools and accessories

that are explicity approved for this power

tool by STIHL or are technically

identical. If you have any questions in

this respect, consult a servicing dealer.

Use only high quality tools and

accessories in order to avoid the risk of

accidents and damage to the machine.

STIHL recommends the use of genuine

STIHL tools and accessories. They are

specifically designed to match the

product and meet your performance

requirements.

Never attempt to modify your power tool

in any way since this may increase the

risk of personal injury. STIHL excludes

all liability for personal injury and

damage to property caused while using

unauthorized attachments.

Do not use a pressure washer to clean

the unit. The solid jet of water may

damage parts of the unit.

Clothing and Equipment

Wear proper protective clothing and

equipment.

Avoid clothing that could get caught on

branches or brush or moving parts of the

machine. Do not wear a scarf, necktie or

jewelry.

WARNING

Wear hearing protection, e.g. earplugs

or ear muffs.

Wear a safety hard hat where there is a

danger of head injuries from falling

objects.

Clothing must be sturdy

but allow complete free-

dom of movement. Wear

snug-fitting clothing, an

overall and jacket combi-

nation, do not wear a

work coat.

Tie up and confine long

hair (e.g. with a hair net,

cap, hard hat, etc.).

Wear sturdy shoes with

non-slip soles.

To reduce the risk of eye

injuries, wear snug-fitting

safety glasses in accord-

ance with European

Standard EN 166. Make

sure the safety glasses

are a good fit.

BT 130

English

4

STIHL offers a comprehensive range of

personal protective clothing and

equipment.

Transporting the Power Tool

Always turn off the engine.

Remove the auger before transporting

the power tool long distances. To reduce

the risk of burn injury, carry the unit by

the handle frame with hot parts of the

machine (e.g. gearbox) away from your

body.

Transporting by vehicle: Properly secure

your power tool to prevent turnover, fuel

spillage and damage.

Fueling

Always shut off the engine before

refueling.

Do not fuel a hot engine – fuel may spill

and cause a fire.

Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly and avoid fuel spillage.

Fuel your power tool only in well-

ventilated areas. If you spill fuel, wipe

the machine immediately – if fuel gets on

your clothing, change immediately.

This reduces the risk of unit vibrations

causing the fuel cap to loosen or come

off and spill quantities of fuel.

Before Starting

Check that your power tool is properly

assembled and in good condition – refer

to appropriate chapters in the instruction

manual.

– Check the fuel system for leaks,

paying special attention to visible

parts such as the tank cap, hose

connections and the manual fuel

pump (on machines so equipped). If

there are any leaks or damage, do

not start the engine – risk of fire.

Have your machine repaired by a

servicing dealer before using it

again.

– Slide control / stop switch must

move easily to STOP or 0.

– Auger brake in good working order.

– Smooth action of throttle trigger and

throttle trigger lockout – throttle

trigger must return automatically to

idle position.

– Check that the spark plug boot is

secure – a loose boot may cause

arcing that could ignite combustible

fumes and cause a fire.

– Never attempt to modify the controls

or safety devices in any way.

– Keep the handles dry and clean –

free from oil and dirt – for safe

control of the power tool.

To reduce the risk of accidents, do not

operate your power tool if it is damaged

or not properly assembled.

Starting the Engine

Start the engine at least 3 meters from

the fueling spot, outdoors only.

Place the unit on level ground, make

sure you have secure footing, hold the

unit securely. Check that the drilling tool

is not touching the ground or any other

object since it may begin to rotate when

the engine starts.

Your power tool is designed to be

operated by one person only. Do not

allow other persons in the work area –

even when starting. To reduce the risk of

injury, avoid contact with the drilling tool.

Do not drop start the power tool – start

the engine as described in the

instruction manual.

Check idle speed setting: The drilling

tool must not rotate when the engine is

idling with the throttle trigger released.

Wear heavy-duty work

gloves made of durable

material (e.g. leather).

Gasoline is an extremely

flammable fuel. Keep

clear of naked flames. Do

not spill any fuel – do not

smoke.

After fueling, tighten

down the screw-type fuel

cap as securely as

possible.

Check for leakage. To

reduce the risk of serious

of fatal burn injuries, do

not start or run the engine

until leak is fixed.

BT 130

English

5

To reduce the risk of fire, keep hot

exhaust gases and hot muffler away

from easily combustible materials (e.g.

wood chips, bark, dry grass, fuel).

Holding and Controlling the Power Tool

Always hold the power tool firmly with

both hands on the handles.

Make sure you always have good

balance and secure footing – auger

brake lever against your left thigh.

Wrap you fingers and thumbs tightly

around the handles – left hand on the

control handle.

During Operation

In the event of impending danger or in

an emergency, switch off the engine

immediately by moving the slide control

/ stop switch to 0 or STOP.

Do not allow any other persons in the

work area. To reduce the risk of injury,

keep a sufficiently safe distance away

from other persons.

The correct engine idle speed is

important to ensure that the drilling tool

stops rotating when you let go of the

throttle trigger. If the drilling tool

continues to rotate when the engine is

idling, have the machine checked by

your servicing dealer. Check and correct

the idle speed setting regularly.

Take special care in slippery conditions

(ice, wet ground, snow), on slopes or

uneven ground.

Watch out for obstacles: Roots and tree

stumps which could cause you to trip or

stumble.

Make sure you always have good

balance and secure footing.

Be particularly alert and cautious when

wearing hearing protection because

your ability to hear warnings (shouts,

alarms, etc.) is restricted.

To reduce the risk of accidents, take a

break in good time to avoid tiredness or

exhaustion.

Work calmly and carefully – in daylight

conditions and only when visibility is

good. Stay alert so as not to endanger

others.

Ensure proper ventilation when working

in trenches, hollows or other confined

locations. This reduces the risk of

serious or fatal injury from breathing

toxic fumes.

To reduce the risk of accidents, stop

work immediately in the event of

nausea, headache, visual disturbances

(e.g. reduced field of vision), problems

with hearing, dizziness, deterioration in

ability to concentrate. Apart from other

possibilities, these symptoms may be

caused by an excessively high

concentration of exhaust gases in the

work area.

Operate your power tool so that it

produces a minimum of noise and

emissions – do not run the engine

unnecessarily, accelerate the engine

only when working.

The dusts (e.g. sawdust), vapor and

smoke produced during operation may

be dangerous to health. If dust levels are

very high, wear a suitable respirator.

To reduce the risk of fire, do not smoke

while operating or standing near your

power tool. Note that combustible fuel

vapor may escape from the fuel system.

9912BA000 KN

Your power tool produces

toxic exhaust fumes as

soon as the engine is

running. These fumes

may be colorless and

odorless and contain

unburned hydrocarbons

and benzol. Never run

the engine indoors or in

poorly ventilated loca-

tions, even if your model

is equipped with a cata-

lytic converter.

BT 130

English

6

If your power tool is subjected to

unusually high loads for which it was not

designed (e.g. heavy impact or a fall),

always check that it is in good condition

before continuing work – see also

"Before Starting". Check the fuel system

in particular for leaks and make sure the

safety devices are working properly. Do

not continue operating your power tool if

it is damaged. In case of doubt, consult

your servicing dealer.

Do not operate your power tool in the

starting throttle position – engine speed

cannot be controlled in this position.

To reduce the risk of injury, do not touch

the auger or drilling spindle unless the

engine is stopped and the auger is at a

standstill.

Hold the machine firmly in order to

control sudden jolts and reactive forces

– keep feed pressure relatively low.

Cover and clearly mark boreholes.

To reduce the risk of injury, shut off the

engine and engage the auger brake

before changing the auger.

To avoid serious burn injuries, avoid

touching hot parts of the machine,

especially the muffler.

Before leaving the power tool

unattended: Shut off the engine.

Check condition of augers regularly.

Replace damaged or dull augers

immediately.

Vibrations

Prolonged use of the power tool may

result in vibration-induced circulation

problems in the hands (whitefinger

disease).

No general recommendation can be

given for the length of usage because it

depends on several factors.

The period of usage is prolonged by:

– Hand protection (wearing warm

gloves)

– Work breaks

The period of usage is shortened by:

– Any personal tendency to suffer

from poor circulation (symptoms:

frequently cold fingers, tingling

sensations).

– Low outside temperatures.

– The force with which the handles

are held (a tight grip restricts

circulation).

Continual and regular users should

monitor closely the condition of their

hands and fingers. If any of the above

symptoms appear (e.g. tingling

sensation in fingers), seek medical

advice.

Maintenance and Repairs

Service the machine regularly. Do not

attempt any maintenance or repair work

not described in the instruction manual.

Have all other work performed by a

servicing dealer.

STIHL recommends that you have

servicing and repair work carried out

exclusively by an authorized STIHL

servicing dealer. STIHL dealers are

regularly given the opportunity to attend

training courses and are supplied with

the necessary technical information.

Only use high-quality replacement parts

in order to avoid the risk of accidents

and damage to the machine. If you have

any questions in this respect, consult a

servicing dealer.

STIHL recommends the use of genuine

STIHL replacement parts. They are

specifically designed to match your

model and meet your performance

requirements.

To reduce the risk of injury, always shut

off the engine before carrying out any

maintenance or repairs or cleaning the

machine. – Exception: Carburetor and

idle speed adjustments.

Do not turn the engine over on the

starter with the spark plug boot or spark

plug removed unless the slide control /

stop switch is on STOP or 0 since there

is otherwise a risk of fire from

uncontained sparking.

To reduce the risk of fire, do not service

or store your machine near open flames.

Check the fuel filler cap for leaks at

regular intervals.

Avoid contact with electri-

cal cables or wires – risk

of electric shock.

Work particularly care-

fully in rocky ground or

ground with a heavy root

structure.

BT 130

English

7

Use only a spark plug of the type

approved by STIHL and make sure it is

in good condition – see "Specifications".

Inspect the ignition lead (insulation in

good condition, secure connection).

Check the condition of the muffler.

To reduce the risk of fire and damage to

hearing, do not operate your machine if

the muffler is damaged or missing.

Do not touch a hot muffler since burn

injury will result.

Vibration behavior is influenced by the

condition of the AV elements – check the

AV elements at regular intervals.

Maintenance, replacement, or repair of

the emission control devices and

systems may be performed by any

nonroad engine repair establishment or

individual. However, if you make a

warranty claim for a component which

has not been serviced or maintained

properly or if nonapproved replacement

parts were used, STIHL may deny

coverage.

For any maintenance please refer to the

maintenance chart and to the warranty

statement near the end of the instruction

manual.

Fitting activating lever for auger brake

N Insert the activating lever (1) into

the clamp

N Place the holder (2) onto the

activating lever

N Screw in the fastening screws (3)

and tighten

Fit the padding

N Hook the padding (1) with the

tabs (2) into the oblong holes in the

handle frame

N Fold up the padding

N Secure the padding to the

handlebar with the cling strips (3) –

do not jam the throttle cable

Assembling the Unit

3

2

3

1

9912BA001 KN

9912BA002 KN

3

9912BA003 KN

BT 130

English

8

The correct throttle cable setting is a

prerequisite for the correct operation of

the warm start, idling and full throttle.

Only set the throttle cable when the

machine is fully installed – the control

handle must be in the working position.

N Use a tool to press the detent on the

control handle onto the end of the

groove

N Open the throttle trigger lockout (1)

and throttle trigger (2) wide (full

throttle setting) – this sets the

throttle cable properly

This engine is certified to operate on

unleaded gasoline and with the mix ratio

50:1.

Your engine requires a mixture of high-

quality premium gasoline and high-

quality two-stroke air-cooled engine oil.

Use premium branded unleaded

gasoline with a minimum octane rating

of 89 (R+M)/2.

Note: Models equipped with a catalytic

converter require unleaded gasoline. A

few tankfuls of leaded gasoline can

reduce the efficiency of the catalytic

converter by more than 50%.

Fuel with a lower octane rating may

result in preignition (causing "pinging")

which is accompanied by an increase in

engine temperature. This, in turn,

increases the risk of the piston seizure

and damage to the engine.

The chemical composition of the fuel is

also important. Some fuel additives not

only detrimentally affect elastomers

(carburetor diaphragms, oil seals, fuel

lines etc.), but magnesium castings as

well. This could cause running problems

or even damage the engine. For this

reason it is essential that you use only

high-quality fuels!

Fuels with different percentages of

ethanol are being offered. Ethanol can

affect the running behaviour of the

engine and increase the risk of lean

seizure.

Gasoline with an ethanol content of

more than 10% can cause running

problems and major damage in engines

with a manually adjustable carburetor

and should not be used in such engines.

Engines equipped with M-Tronic can be

run on gasoline with an ethanol content

of up to 25% (E25).

Use only STIHL two-stroke engine oil or

equivalent high-quality two-stroke air-

cooled engine oils for mixing.

We recommend STIHL 50:1 two-stroke

engine oil since it is specially formulated

for use in STIHL engines.

To ensure the maximum performance of

your STIHL engine, use a high quality 2-

cycle engine oil. To help your engine run

cleaner and reduce harmful carbon

deposits, STIHL recommends using

STIHL HP Ultra 2-cycle engine oil or ask

your dealer for an equivalent fully

synthetic 2-cycle engine oil.

To meet the requirements of EPA and

CARB we recommend to use STIHL HP

Ultra oil.

Do not use BIA or TCW (two-stroke

water cooled) mix oils!

Use only STIHL 50:1 heavy-duty engine

oil or an equivalent quality two-stroke

engine oil for the fuel mix in models

equipped with a catalytic converter.

Take care when handling gasoline.

Avoid direct contact with the skin and

avoid inhaling fuel vapour.

The canister should be kept tightly

closed in order to avoid any moisture

getting into the mixture.

Adjusting the Throttle Cable

9912BA004 KN

2

1

9912BA005 KN

Fuel

BT 130

English

9

The fuel tank and the canister in which

fuel mix is stored should be cleaned

from time to time.

Fuel mix ratio

Only mix sufficient fuel for a few days

work, not to exceed 30 days of storage.

Store in approved safety fuel-canisters

only. When mixing, pour oil into the

canister first, and then add gasoline.

Dispose of empty mixing-oil canisters

only at authorized disposal locations.

Preparing the machine

N Before fueling, clean the filler cap

and the area around it so that dirt

cannot fall into the tank

N Always position the machine so that

the filler cap is facing upwards

Refuelling

Take care not to spill fuel while fueling

and do not overfill the tank. STIHL

recommends use of the STIHL filling

system for fuel (special accessory).

N Opening the twist lock

N Refuelling

N Closing the filler cap

WARNING

After fueling, tighten down the filler cap

by hand as securely as possible.

Examples

Gasoline Oil (STIHL 50:1 or equiva-

lent high-quality oils)

liters liters (ml)

10.02(20)

5 0.10 (100)

10 0.20 (200)

15 0.30 (300)

20 0.40 (400)

25 0.50 (500)

Fueling

9912BA006 KN

BT 130

English

10

Activating the auger brake

N Set the activating lever to A

– when starting

– when idling

– to unscrew a secured auger

If the auger catches in the drilled hole

(e. g. on roots or stones), the auger

moves counterclockwise – the activating

lever is pushed against the thigh of the

operator and the auger brake is

triggered.

Releasing the auger brake

N Set the activating lever to B

Checking the auger brake for proper

functioning

The auger brake is subject to normal

wear. Before starting work and after

releasing a jammed auger, check

regularly if it is fulfilling its function.

Each time before starting work and after

releasing a jammed auger

N When idling, activate the auger

brake and open the throttle wide for

a brief period (max. 3 seconds) –

the auger must not rotate.

If the auger brake fails, it must be

repaired immediately by a servicing

dealer – STIHL recommends the STIHL

dealer.

N Switch off the motor and activate the

auger brake – see "Auger brake"

N Put down the auger – drilling spindle

facing upwards

N Pull the retaining pin (1) out of the

auger shaft

N Push the auger (2) onto the drilling

spindle until the holes (3) align

N Insert the retaining pin into the hole

N Fold down the spring clip of the

retaining pin so that it encloses the

auger shaft

Auger Brake

9912BA008 KN

A

9912BA009 KN

B

Fitting the Auger

9912BA010 KN

1

2

3

BT 130

English

11

Engaging the Auger Brake

N Move the activating lever to

position A .

Starting

N Press down the trigger lockout

lever (1), then squeeze the throttle

trigger (2)

N and hold them in that position.

N Move the slide control (3) to START

and hold it there.

N Now release the throttle trigger,

slide control and trigger lockout in

that order. This is the starting

throttle position.

N Set the choke knob (4) to:

N Press the manual fuel pump

bulb (5) at least five times.

Starting / Stopping the

Engine

9912BA008 KN

A

9912BA011 KN

START

g if the engine is cold

e for warm start – also use this posi-

tion if the engine has been running

but is still cold.

4

5

9912BA012 KN

BT 130

English

12

Cranking

N Place the unit on the ground so that

it is secure.

N Put your left foot on the handle

frame.

N Left hand on the handle frame.

N Pull the starter grip slowly with your

right hand until you feel it engage

and then give it a brisk strong pull.

NOTICE

Do not pull out the starter rope all the

way – it might otherwise break.

N Do not let the starter grip snap back.

Guide it slowly back into the housing

so that the starter rope can rewind

properly.

N Continue cranking.

When engine begins to fire

N Set the choke knob to e and

N continue cranking until the engine

runs.

As soon as the engine runs

N Blip the throttle trigger (2) – the slide

control (3) moves to the run

position F and the engine settles

down to idling speed.

NOTICE

Since the auger brake is still engaged,

the engine must be returned to idling

speed immediately – or the clutch might

otherwise be damaged.

N Stand the unit on the tip of the

auger.

N Disengage the auger brake by

moving the activating lever to

position B. Your earth auger is now

ready for operation.

Make sure the carburetor is correctly

adjusted. The auger must not rotate

when the engine is idling.

Stopping the Engine

N Move the slide control to STOP-0.

At very low outside temperatures

N When the engine starts, blip the

throttle trigger to disengage the

starting throttle position – the slide

9912BA013 KN

9912BA014 KN

9912BA009 KN

B

BT 130

English

13

control moves to the run position F

and the engine settles down to idling

speed.

N Open the throttle slightly.

N Warm up the engine for a short

period.

If engine does not start

If you did not move the choke knob

quickly enough to e after the engine

began to fire, the engine is flooded.

N Set the choke knob to e and

N Set the slide control, trigger lockout

and throttle trigger to the starting

throttle position.

N Start the engine by pulling the

starter rope briskly – 10 to 20 pulls

may be necessary.

If the engine still does not start

N Move the slide control to STOP-0.

N Remove the spark plug – see

"Spark Plug".

N Dry the spark plug.

N Crank the engine several times with

the starter to clear the combustion

chamber.

N Refit the spark plug – see "Spark

Plug".

N Move the slide control to START.

N Set the choke knob to e – even if

the engine is cold.

N Now start the engine.

Throttle cable adjustment

N Check adjustment of throttle cable –

see chapter on "Adjusting the

Throttle Cable".

If fuel tank has been run completely dry

and then refueled

N After refueling, press the manual

fuel pump bulb at least five times –

even if the bulb is filled with fuel.

N Set the choke knob according to

engine temperature.

N Now start the engine.

During break-in period

A factory-new machine should not be

run at high revs (full throttle off load) for

the first three tank fillings. This avoids

unnecessary high loads during the

break-in period. As all moving parts

have to bed in during the break-in

period, the frictional resistances in the

engine are greater during this period.

The engine develops its maximum

power after about 5 to 15 tank fillings.

During Operation

After a long period of full throttle

operation, allow the engine to run for a

short while at idle speed so that engine

heat can be dissipated by the flow of

cooling air. This protects engine-

mounted components (ignition,

carburetor) from thermal overload.

After Finishing Work

Storing for a short period: Wait for the

engine to cool down. To avoid

condensation, fill the fuel tank and keep

the machine in a dry place, well away

from sources of ignition, until you need it

again. For longer out-of-service periods

– see "Storing the Machine".

Operating Instructions

BT 130

English

14

Working with shaft extension (special

accessory)

Do not fit the shaft extension until the full

length of the auger is in the hole.

WARNING

Starting a hole with the shaft extension

fitted increases the risk of personal

injury because the unit is then at chest

height and cannot be controlled

properly. For the same reason the shaft

extension must be removed before the

auger is pulled out of the hole.

Inspection by a specialist

If the machine is used commercially, it

must be inspected at least once a year

by a specialist.

Specialists are persons with the

technical training and experience

necessary to assess the safe working

condition of the earth auger.

If the auger is jammed in the drilling hole

N Switch off the engine immediately

N Set the slide control to STOP-0

N Set the activating lever to A – the

auger brake is activated

N Turn the whole auger

counterclockwise to the left until the

auger is released again

N Once the jammed auger is

released, check that the auger

brake functions properly – see

"Auger brake"

If there is a noticeable loss of engine

power

N Remove the padding on the handle

frame

N Unscrew the screw (1) and remove

the filter cover (2) – screw is

fastened in the filter cover so that it

is secured against loss

N Remove coarse dirt from inside the

filter cover (2) and around the air

filter (3)

N Remove and examine the air

filter (3) – replace if soiled or

damaged

N Fit the air filter (3)

N Fit the filter cover (2)

N Screw in the screw (1) and tighten

N Fit the padding – see “Assembling

the machine”

Releasing a Trapped Auger

9912BA008 KN

A

Replacing the Air Filter

9912BA017 KN

1

BT 130

English

15

Exhaust emissions are controlled by the

design of the fundamental engine

parameters and components (e.g.

carburation, ignition, timing and valve or

port timing) without the addition of any

major hardware.

The carburetor of the machine has been

adjusted for optimum performance and

fuel efficiency in all operating states at

the factory.

Setting the idle speed

Engine stops when idling

N Turn the idle speed adjusting

screw (LA) slowly clockwise until

the engine runs smoothly.

Auger turns when idling

N Turn the idle speed adjusting

screw (LA) slowly counterclockwise

until the auger stops turning

WARNING

If the auger continues to keep moving in

idle even after adjustment, have the

machine checked by a servicing dealer.

Engine Management Adjusting the Carburetor

9912BA018 KN

BT 130

English

16

N If the engine is down on power,

difficult to start or runs poorly at idle

speed, first check the spark plug.

N Fit a new spark plug after about 100

operating hours – or sooner if the

electrodes are badly eroded. Install

only suppressed spark plugs of the

type approved by STIHL – see

"Specifications".

Removing the spark plug

N Set the slide control to STOP-0

N Unplug spark plug boot (1)

N Unscrew spark plug

Checking the Spark Plug

N Clean dirty spark plug.

N Check electrode gap (A) and

readjust if necessary – see

"Specifications".

N Rectify the problems which have

caused fouling of the spark plug.

Possible causes are:

– Too much oil in fuel mix.

– Dirty air filter.

– Unfavorable running conditions.

WARNING

Arcing may occur if the adapter nut (1) is

loose or missing. Working in an easily

combustible or explosive atmosphere

may cause a fire or an explosion. This

can result result in serious injuries or

damage to property.

N Use resistor type spark plugs with a

properly tightened adapter nut.

Installing the spark plug

N Screw the spark plug (3) into the

cylinder and fit the boot (2) (press it

down firmly).

Spark Plug

9912BA015 KN

000BA039 KN

A

1

000BA045 KN

3

002BA178 KN

2

BT 130

English

17

If engine running behavior is still

unsatisfactory after the air filter has been

serviced and the carburetor and throttle

cable have been adjusted correctly, the

cause may also be in the muffler.

Have the muffler checked for

contamination (coking) by a servicing

dealer!

STIHL recommends that maintenance

and repair work be carried out only by

authorized STIHL dealers.

N Check the lubricant filling

periodically – approx. every

50 hours of operation

N Remove the screw plug (1)

If no grease can be seen on the inside of

the screw plug:

N Apply tube (2) of gear lubricant

N Squeeze grease into the gear

housing – approx. 5 to 10 g

N Do not completely fill the gear

housing with grease

N Refit locking screw and tighten

securely

For periods of 3 months or longer

N Remove the drilling tool.

N Drain and clean the fuel tank in a

well ventilated area.

N Dispose of fuel properly in

accordance with local

environmental requirements.

N Run the engine until the carburetor

is dry – this helps prevent the

carburetor diaphragms sticking

together.

N Thoroughly clean the machine – pay

special attention to the cylinder fins

and air filter.

N Store the machine in a dry, high or

locked location, out of the reach of

children and other unauthorized

persons.

Engine Running Behavior Lubricating the Gearbox

1

9912BA019 KN

9912BA020 KN

Storing the Machine

BT 130

English

18

Maintenance work

STIHL recommends that maintenance

and repair work be carried out only by

authorized STIHL dealers.

Fuel pickup body in tank

N Have the fuel pickup body in the fuel

tank changed once every year

Spark arrestor in muffler

N If engine performance deteriorates,

have the spark arresting screen in

the muffler checked

Inspections and Maintenance

by Dealer

La page charge ...

STIHL BT 130 Manuel utilisateur

STIHL BT 130 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents