Magtek Bullet Quick Installation Guide

Catégorie
Lecteurs de cartes
Taper
Quick Installation Guide
BulleT (SPP
*
and KB
**
)
Secure Card Reader Authenticator
Quick Installation Guide
www.magtek.com
Security anywhere. With the BulleT Secure Card Reader Authenticator (SCRA),
security comes with the exibility and portability of a wireless connection. Small
enough to t into the palm of your hand, the BulleT enables secure wireless
communications with a PC or mobile phone using a popular wireless interface. Not
only does the BulleT encrypt card data from the moment the card is swiped, but it
also enables card authentication to immediately detect counterfeit or altered cards.
* BulleT SPP (serial port prole) is designed for Android and Windows OS where
Serial Port Prole is supported.
** BulleT KB (wireless keyboard) is designed for computing devices connected to
wireless keyboard. (iOS, Android, Windows and Mac OS)
Product Description
Diagram
Specications
Figure 1. Contents
The power switch is located on the front of the reader.
Press to turn on (default is 120 seconds).
Hold 1 second to extend on.
Hold 3 seconds to turn off.
Power Switch
LED Indicator (Charging)
Connection: Wireless or USB
Interface: Wireless (USB is used for charging the battery)
Power: Battery powered; battery is charged from a 5V source, e.g.,
USB bus
Card Speed: 4 to 60 ips
Electrical Current: 100mA maximum during charge
Operating Temp: 32°F - 113°F ( 0 - 45°C)
Operating Humidity: 10% to 90% noncondensing
Accessories: Optional stylus is available
MICRO USB B PLUG
CON 1 CON 2
Figure 2. micro-USB cable
micro-USB connection USB connection
Additional Contents
Magstripe swipe path
Connection
Compatibility and Operating System
Power and Charging
www.magtek.com
Charge: Attach the USB cable. It takes approximately 2.5 hours to fully charge the
battery and it will stay charged for approximately 100 card swipes. The LED will
slowly blink amber while the battery is charging and then turn solid amber when the
battery is fully charged (for best results, allow the battery to fully charge).
Power USB HID connection: Insert the Micro-B end of the cable into Micro-B port on
the bottom of the reader and the Standard-A connector into a USB port on the PC/
Mac. USB connection will automatically detect your device.
Mobile: BulleT KB/SPP Connection
1. Pull up Applications or Menu and select Settings.
2. Select wireless and network.
3. Select wireless settings.
4. Turn on the BulleT reader, (green light will ash while connecting.)
5. Select Scan for devices.
6. Select the MAGTEK-xxxx device when it appears on the screen.
7. The screen will prompt you for a PIN (the default is 1234).
8. BulleT KB device is paired and ready to use.
BulleT SPP device requires you to go to the application.
Follow the application screen prompts to connect to wireless device.
After it is connected, the device is ready to use.
Personal Computer (PC): BulleT KB/SPP Connection
1. If prompted for a passkey use 1234.
2. Attach a wireless adapter to the PC.
3. Select wireless icon in Control Panel.
4. Click Add.
5. Check My device is set up and ready to be found.
6. Then click Next.
7. Select the MAGTEK-xxxx device (number indicated on the reader).
8. Then click Next.
9. Select Let me choose my own passkey.
10. Then type “1234” in the associated box.
11. Click Next when ready. Wait for the device to be installed.
13. After the device is installed, note the Outgoing COM port (if using BulleT SPP): for
communication purposes. If using BulleT KB, it will interact with the connected PC as a wireless
Keyboard.
14. Click Finish. The BulleT reader is now ready to use.
NOTE: UNINSTALL ANY EXISTING WIRELESS SOFTWARE PRIOR TO BEGINNING
INSTALLATION. DO NOT PLUG USB ADAPTER IN UNTIL INSTRUCTED TO DO SO.
Insert the Micro-B end of the cable into Micro-B port on the bottom of the reader and
the Standard-A connector into a USB port on the PC/Mac.
Compliance
FCC WARNING STATEMENT: This equipment has been tested and was found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference with radio communications. However, there is no guarantee that interference will not occur
in a particular installation.
FCC COMPLIANCE STATEMENT: This device complies with Part 15 of the FCC Rules. Operation of this device is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CANADIAN DOC STATEMENT: This digital apparatus does not exceed the Class B limits for radio noise from digital apparatus set out in the Radio Interference Regulations of the Canadian
Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe B prescrites dans le Réglement sur le brouillage
radioélectrique édicté par le ministère des Communications du Canada.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numériqué de la classe B est conformé à la norme NMB-003 du Canada.
CE STANDARDS: Testing for compliance with CE requirements was performed by an independent laboratory.
The unit under test was found compliant with standards established for Class B devices.
UL/CSA: This product is recognized per Underwriter Laboratories and Canadian Underwriter Laboratories 1950.
RoHS STATEMENT: When ordered as RoHS compliant, this product meets the Electrical and Electronic Equipment (EEE) Reduction of Hazardous Substances (RoHS) European Directive 2002/95/
EC. The marking is clearly recognizable, either as written words like “Pb-free”, “lead-free”, or as another clear symbol ( ).
Pb
Registered to ISO 9001:2000 © Copyright 2016 MagTek, Inc. PN D99875377 rev. 60 5/16
MagTek ® Inc., 1710 Apollo Court, Seal Beach CA 90740 p 562-546-6400 | f 562-546-6301 | 800-788-6835 | www.magtek.com
LEDs
Technical Support
When calling the support team please have your reader charged and have the part
number and serial number(s) available.
651.415.6800
LED Color LED Condition USB
Connection
Meaning
Off n/a No power
Green Steady On -- Ready to read a card—after power button
pushed
Green Rapid Flashing No Searching for connection
Green Slow Blinking -- Authentication has been established;
ready to read a card
Green On 2 seconds -- Good Read
Amber Steady On Yes Battery fully charged
Amber Short Flash No After power button is pushed
Amber Slow Blinking Yes Battery charging
Red Steady On -- Authentication failed
Red Rapid Flashing Yes Battery voltage too low to operate
normally
Red On 2 seconds -- Bad card swipe
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Magtek Bullet Quick Installation Guide

Catégorie
Lecteurs de cartes
Taper
Quick Installation Guide

dans d''autres langues