Please read these instructions carefully before using this product, and save this manual for future use.
5.7~19” Arm-based HMI
Freescale® Cortex® A9 i.MX6 Dual Core, 1 GHz
Android 6.0
Front IP65
Model No.: R05FA3S-IPD1HMHB
W07FA3S-IPA3HM
W10FA3S-IPH1HM
R15FA3S-IPC3HM
R19FA3S-IPM1HM
User Manual
Document Version 1.0
Document Part Number: 91521110103V
2
Arm-based Front IP65 HMI User Manual
Contents
Preface ................................................................................................................................. 4
About This User Manual ..................................................................................................... 9
Chapter 1: Introduction .................................................................................................... 10
1.1 Introduction ........................................................................................................ 11
1.2 Product Features ................................................................................................ 11
1.3 Package Contents .............................................................................................. 11
1.4 Connector Description ........................................................................................ 12
1.5 Mechanical Dimensions ..................................................................................... 13
Chapter 2: Getting Started ............................................................................................... 16
2.1 Powering On ...................................................................................................... 17
2.1.1 AC Adapter Components .......................................................................... 17
2.1.2 Power Considerations............................................................................... 17
2.1.3 Connecting the Power .............................................................................. 18
2.2 Connector Description ........................................................................................ 19
2.2.1 Power Input Connector ............................................................................. 19
2.2.2 Serial Port Connector ............................................................................... 19
2.2.3 Ethernet Connector .................................................................................. 19
2.2.4 USB 2.0 Connector ................................................................................... 20
2.2.5 USB OTG Connector ................................................................................ 20
2.2.6 CANBus Connector .................................................................................. 20
2.2.7 Micro HDMI Connector ............................................................................. 21
2.3 Turning On and Off the HMI Device ................................................................... 21
2.4 Configuring Serial Port Settings ......................................................................... 22
Chapter 3: Mounting ......................................................................................................... 24
3.1 Cable Mounting Considerations ......................................................................... 25
3.2 Safety Precautions ............................................................................................. 25
3.3 Mounting Guide .................................................................................................. 25
3.3.1 Panel Mount ............................................................................................. 26
3.3.2 VESA Mount ............................................................................................. 27
Chapter 4: Operating the Device ..................................................................................... 28
4.1 Operating System ............................................................................................... 29
4.2 Multi-Touch ........................................................................................................ 29
4.3 System Settings ................................................................................................. 30
4.3.1 Set up the Device ..................................................................................... 30
4.3.2 Home Screen ............................................................................................ 30
4.3.3 Quick Settings .......................................................................................... 31
3
Preface
4.4 Ethernet .............................................................................................................. 32
4.4.1 Configuring Ethernet ................................................................................. 33
4.4.2 Checking Ethernet Settings ...................................................................... 34
4.5 Winmate® Home Manager (WHM)..................................................................... 35
4.5.1 How to Lock Applications .......................................................................... 35
4.5.2 How to Unlock Applications ...................................................................... 38
4.5.3 How to Change Password ........................................................................ 39
Chapter 5: Software Installation ...................................................................................... 40
5.1 Android Debug Bridge (ADB) Driver Installation ................................................. 41
5.1.1 Disabling Driver Signature on Windows 8................................................. 42
5.1.2 ADB Driver Installation.............................................................................. 46
5.2 Installing Android Debug Bridge (ADB) .............................................................. 50
5.2.1 Installing Android Debug Bridge (ADB)..................................................... 50
5.2.2 Using Android Debug Bridge (ADB) ......................................................... 50
5.3 Downloading Image Tool .................................................................................... 52
5.4 OTA Update Guide ............................................................................................. 52
5.5 OS Image Update Guide .................................................................................... 56
Chapter 6: Technical Support .......................................................................................... 57
6.1 Introduction .................................................................................................... - 58 -
6.2 Problem Report Form ..................................................................................... - 58 -
Appendix A: Product Specifications ............................................................................... 59
4
Arm-based Front IP65 HMI User Manual
Preface
Copyright Notice
No part of this document may be reproduced, copied, translated, or transmitted in any form or
by any means, electronic or mechanical, for any purpose, without the prior written permission
of the original manufacturer.
Trademark Acknowledgement
Brand and product names are trademarks or registered trademarks of their respective owners.
Disclaimer
We reserve the right to make changes, without notice, to any product, including circuits and/or
software described or contained in this manual in order to improve design and/or performance.
We assume no responsibility or liability for the use of the described product(s) conveys no
license or title under any patent, copyright, or masks work rights to these products, and make
no representations or warranties that these products are free from patent, copyright, or mask
work right infringement, unless otherwise specified. Applications that are described in this
manual are for illustration purposes only. We make no representation or guarantee that such
application will be suitable for the specified use without further testing or modification.
Warranty
Our warranty guarantees that each of its products will be free from material and workmanship
defects for a period of one year from the invoice date. If the customer discovers a defect, we
will, at his/her option, repair or replace the defective product at no charge to the customer,
provide it is returned during the warranty period of one year, with transportation charges
prepaid. The returned product must be properly packaged in its original packaging to obtain
warranty service. If the serial number and the product shipping data differ by over 30 days, the
in-warranty service will be made according to the shipping date. In the serial numbers the third
and fourth two digits give the year of manufacture, and the fifth digit means the month (e. g.,
with A for October, B for November and C for December).
For example, the serial number 1W18Axxxxxxxx means October of year 2018.
Customer Service
We provide a service guide for any problem by the following steps: First, visit the website of
our distributor to find the update information about the product. Second, contact with your
distributor, sales representative, or our customer service center for technical support if you
need additional assistance.
You may need the following information ready before you call:
Product serial number
Software (OS, version, application software, etc.)
Description of complete problem
The exact wording of any error messages
In addition, free technical support is available from our engineers every business day. We are
always ready to give advice on application requirements or specific information on the
installation and operation of any of our products.
5
Preface
Advisory Conventions
Four types of advisories are used throughout the user manual to provide helpful information or to
alert you to the potential for hardware damage or personal injury. These are Notes, Important,
Cautions, and Warnings. The following is an example of each type of advisory.
Note:
A note is used to emphasize helpful information
Important:
An important note indicates information that is important for you to know.
Caution/ Attention
A Caution alert indicates potential damage to hardware and explains how to avoid
the potential problem.
Une alerte d’attention indique un dommage possible à l’équipement et explique
comment éviter le problème potentiel.
Warning!/ Avertissement!
An Electrical Shock Warning indicates the potential harm from electrical hazards
and how to avoid the potential problem.
Un Avertissement de Choc Électrique indique le potentiel de chocs sur des
emplacements électriques et comment éviter ces problèmes.
Alternating Current Mise à le terre !
The Protective Conductor Terminal (Earth Ground) symbol indicates the potential
risk of serious electrical shock due to improper grounding.
Le symbole de Mise à Terre indique le risqué potential de choc électrique grave
à la terre incorrecte.
6
Arm-based Front IP65 HMI User Manual
Safety Information
Warning!/ Avertissement!
Always completely disconnect the power cord from your chassis whenever you
work with the hardware. Do not make connections while the power is on.
Sensitive electronic components can be damaged by sudden power surges.
Only experienced electronics personnel should open the PC chassis.
Toujours débrancher le cordon d’alimentation du chassis lorsque vous travaillez
sur celui-ci. Ne pas brancher de connections lorsque l’alimentation est
présente. Des composantes électroniques sensibles peuvent être
endommagées par des sauts d’alimentation. Seulement du personnel
expérimenté devrait ouvrir ces chassis.
Caution/ Attention
Always ground yourself to remove any static charge before touching the
CPU card. Modern electronic devices are very sensitive to static electric
charges. As a safety precaution, use a grounding wrist strap at all times.
Place all electronic components in a static-dissipative surface or static-
shielded bag when they are not in the chassis.
Toujours verifier votre mise à la terre afin d’éliminer toute charge statique
avant de toucher la carte CPU. Les équipements électroniques moderns
sont très sensibles aux décharges d’électricité statique. Toujours utiliser un
bracelet de mise à la terre comme précaution. Placer toutes les
composantes électroniques sur une surface conçue pour dissiper les
charge, ou dans un sac anti-statique lorsqu’elles ne sont pas dans le
chassis.
For your safety carefully read all the safety instructions before using the device. Keep
this user manual for future reference.
Always disconnect this equipment from any AC outlet before cleaning. Do not use
liquid or spray detergents for cleaning. Use a damp cloth.
For pluggable equipment, the power outlet must be installed near the equipment
and must be easily accessible.
Keep this equipment away from humidity.
Put this equipment on a reliable surface during installation. Dropping it or letting it
fall could cause damage.
The openings on the enclosure are for air convection and to protect the equipment
from overheating.
Before connecting the equipment to the power outlet make sure the voltage of the
power source is correct.
Position the power cord so that people cannot step on it. Do not place anything over
the power cord.
If the equipment is not used for a long time, disconnect it from the power source to
avoid damage by transient over-voltage.
Never pour any liquid into an opening. This could cause fire or electrical shock.
Never open the equipment. For safety reasons, only qualified service personnel
should open the equipment.
All cautions and warnings on the equipment should be noted.
7
Preface
*Let service personnel to check the equipment in case any of the following
problems appear:
o The power cord or plug is damaged.
o Liquid has penetrated into the equipment.
o The equipment has been exposed to moisture.
o The equipment does not work well or you cannot get it to work according to
the user manual.
o The equipment has been dropped and damaged.
o The equipment has obvious signs of breakage.
Do not leave this equipment in an uncontrolled environment where the storage
temperature is below -20°C (-4°F) or above 60°C (140°F). It may damage the
equipment.
Caution/Attention
Use the recommended mounting apparatus to avoid risk of injury.
Utiliser l’appareil de fixation recommandé pour éliminer le risque de
blessure.
Warning!/ Avertissement!
Only use the connection cords that come with the product. When in doubt,
please contact the manufacturer.
Utiliser seulement les cordons d’alimentation fournis avec le produit. Si
vous doutez de leur provenance, contactez le manufacturier.
Warning!/ Avertissement!
Always ground yourself against electrostatic damage to the device.
Toujours vérifier votre mise à la terre afin que l’équipement ne se décharge
pas sur vous.
Cover workstations with approved anti-static material. Use a wrist strap connected
to a work surface and properly grounded tools and equipment.
Use anti-static mats, heel straps, or air ionizer for added protection.
Avoid contact with pins, leads, or circuitry.
Turn off power and input signals before inserting and removing connectors or test
equipment.
Keep the work area free of non-conductive materials, such as ordinary plastic
assembly aids and Styrofoam.
Use filed service tools, such as cutters, screwdrivers, and vacuum cleaners that
are conductive.
Always put drivers and PCB’s component side on anti-static foam.
8
Arm-based Front IP65 HMI User Manual
Important Information
Federal Communications Commission Radio Frequency Interface Statement
This device complies with part 15 FCC rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a class "B" digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference
at him own expense.
EC Declaration of Conformity
This equipment is in conformity with the requirement of the following EU legislations
and harmonized standards. Product also complies with the Council directions.
Electromagnetic Compatibility Directive (2014/30/EU)
EN55024: 2010 EN 55022: 2010 Class B
o IEC61000-4-2: 2009
o IEC61000-4-3: 2006+A1: 2007+A2: 2010
o IEC61000-4-4: 2012
o IEC61000-4-5: 2014
o IEC61000-4-6: 2013
o IEC61000-4-8: 2010
o IEC61000-4-11: 2004
EN55022: 2010/AC:2011
EN61000-3-2:2014
EN61000-3-3:2013
Low Voltage Directive (2014/35/EU)
EN 60950-1:2006/A11:2009/A1:2010/A12:2011/ A2:2013
9
About This User Manual
About This User Manual
This User Manual provides information about using the Winmate® Arm-based Front IP65 HMI.
This User Manual applies to the Arm-based Front IP65 HMI.
The documentation set for the Arm-based Front IP65 HMI with Freescale® Cortex® A9 i.MX6 Dual
Core provides information for specific user needs, and includes:
Arm-based Front IP65/ NEMA4 HMI User Manual – contains detailed description on how
to use the HMI device, its components and features.
Note:
Some pictures in this guide are samples and can differ from actual product.
Models
Screen Size
Model Name
5.7
R05FA3S-IPD1HMHB
7”
W07FA3S-IPA3HM
10.1”
W10FA3S-IPH1HM
15”
R15FA3S-IPC3HM
19”
R19FA3S-IPM1HM
Document Revision History
Version
Date
Note
1.0
18-Jan-2019
Initial document release
10
Arm-based Front IP65 HMI User Manual
Chapter 1: Introduction
This chapter gives you product overview, describes features and
hardware specification. You will find all accessories that come
with the HMI in the packing list. Mechanical dimensions and
drawings included in this chapter.
11
Chapter 1: Introduction
1.1 Introduction
Congratulations on purchasing Winmate® Arm-based Front IP65 HMI. Winmate continues
developing new generation of Human Machine Interfaces for Industry 4.0 and Internet of Things
(IoT).
Our Arm-based Front IP65 HMI runs on Android 6.0 operating system that allows installing the
latest applications (APPs). There is one USB 2.0 onboard to connect mouse or keyboard, Micro
USB OTG for system updates. System memory LPDDR3 of 1 GB ensures stable operation of
applications. Waterproof enclosure protects HMI from water splashes and dust that makes it
suitable for industrial applications.
1.2 Product Features
Winmate® Arm-based Front IP65 HMI features:
5.7/ 7/10.1/15/ 19-inch widescreen panel
Freescale® Cortex® A9 i.MX6 Dual Core, 1 GHz
Android 6.0 operating system
Resistive touch
1 x USB 2.0; 1 x RS-232/422/485; 1 x Micro SD Slot, 1 x Mini USB, 1 x Micro HDMI
Optional PoE function
Front IP65 water and dust proof
1.3 Package Contents
Carefully remove the box and unpack your device. Package content may vary based on your order.
Please check if all the items listed below are inside your package. If any of these items are missing
or damaged contact us immediately.
Standard factory shipment list:
HMI Device
Varies by product specifications
User Manual (Hardcopy)
Part No. 91521110103V
Driver CD
Part No.
AC Adapter
(12V/ 50W)
Part No. 922D050W12VA
Power Cord
Varies by country
2 pin Terminal Block
Part No. 94J602G020K0
12
Arm-based Front IP65 HMI User Manual
1.4 Connector Description
Terminal interfaces are located on the bottom side of the HMI device.
Note:
Notice that input and output connectors vary by product size and
specifications.
Terminal interfaces description:
Item
Description
RJ45 – Connects HMI device to Ethernet network. Supports PoE for
power transmission in network equipment, via network UTP cable,
together with data.
USB 2.0- Connects USB2.0 compatible devices to HMI device.
Example: A printer to HMI device.
USB OTG –. Connect to PC for client use and update OS Image.
MicroSD Card Slot –Insert microSD card to expand the storage.
RS-232/422/485 –
Example: A barcode reader or scanner to HMI device.
CANBus – Allow device to communicate with each other without host
computer.
Example: A machine controller to HMI device.
2 Pin Terminal Block – Use to provide DC power to HMI device.
Micro HMDI – Transmits audio and video to external monitor.
Example: Project the HMI device screen to external monitor.
Mini USB – Use to update software on the HMI device.
13
Chapter 1: Introduction
1.5 Mechanical Dimensions
This section describes physical appearance of the HMI.
The picture above shows only a prototype model for information purposes only.
5.6-inch, R05FA3S-IPD1HMHB
Unit: mm
Dimensions : 188 x 148 x 59
Cutout Dimensions: 162 x 118
7-inch, W07FA3S-IPA3HM
Unit: mm
Dimensions : 218 x 164.6 x 56.8
Cutout Dimensions: 192 x 128
14
Arm-based Front IP65 HMI User Manual
10.1-inch, W10FA3S-IPH1HM
Unit: mm
Dimensions : 286 x 176 x 49.5
Cutout Dimensions: 239 x 162
15-inch, R15FA3S-IPC3HM
Unit: mm
Dimensions : 400 x 292 x 59
Cutout Dimensions: 360 x 292
15
Chapter 1: Introduction
19-inch, R19FA3S-IPM1HM
Unit: mm
Dimensions : 474 x 384 x 71.4
Cutout Dimensions: 432.5 x 342.5
16
Arm-based Front IP65 HMI User Manual
Chapter 2: Getting Started
This chapter tells you important information on power supply, adapter
and precautions tips. Pay attention to power considerations.
17
Chapter 2: Getting Started
2.1 Powering On
2.1.1 AC Adapter Components
Safety Precautions:
Do not use the adapter in a high moisture environment
Never touch the adapter with wet hands or foot
Allow adequate ventilation around adapter while using
Do not cover the adapter with paper or other objects that will reduce cooling
Do not use the adapter while it is inside a carrying case
Do not use the adapter if the cord is damaged
There are NO serviceable parts inside
Replace the unit if it is damaged or exposed to excess moisture
While using the AC Adapter always:
Plug-in the power cord to easy accessible AC outlet
Plug-in the AC adapter to a grounded outlet
2.1.2 Power Considerations
The HMI device operates on external DC power. Use the AC adapter included in the package.
Caution/ Attention
Use only the AC adapter included in your package
(Rating: Output 12 V/ 6.6A). Using other AC adapters may damage the device.
Utiliser seulement le convertisseur AC inclu avec votre appareil (Puissance: Sortie
12 V/ 6.6A). Utiliser d’autres convertisseurs pourraient endommager l’appareil.
AC Adapter
Power Cord
2 Pin Terminal Block
to DC Jack
Alternating Current/ Mise à le terre !
This product must be grounded. Use only a grounded AC outlet. Install the
additional PE ground wire if the local installation regulations require it.
*If you do not use a grounded outlet while using the device, you may notice an
electrical tingling sensation when the palms of your hands touch the device.
[FR]Ce produit doit être mis à la terre. Utiliser seulement un cordon
d’alimentation avec mise à la terre. Si les règlements locaux le requiert, installer
des câbles de mise à la terre supplémentaires.
*Si vous n’utiliser pas une prise d’alimentation avec mise à la terre, vous pourriez
remarquer une sensation de picotement électrique quand la paume de vos mains
touche à l’appareil.
18
Arm-based Front IP65 HMI User Manual
2.1.3 Connecting the Power
Installation Instruction:
1. Connect a 2-pin terminal block to the HMI connector.
2. Connect the other side of the terminal block to the AC adapter.
3. Connect the AC adapter to the power cord.
4. Plug in the power cord to a working AC wall outlet. The device will boot automatically.
Note:
Based on the model, terminal block connector may be located either
on the bottom or on the rear side of the HMI device.
Note:
Power cords vary in appearance by region and country.
19
Chapter 2: Getting Started
2.2 Connector Description
2.2.1 Power Input Connector
The DC power source input of the panel PC is a 2 pin terminal block connector that supports 12 V
DC power input.
Pin assignments and signal name of power input terminal block
2.2.2 Serial Port Connector
The HMI device has one RS-232/422/485 serial port connector to connect your device to
external devices.
Pin assignments and signal name of serial port connector
Serial port settings can be configured in Winmate application for Android OS. Refer to “Configuring
Serial Port Settings” of this User Manual for more details.
2.2.3 Ethernet Connector
The HMI device supports one RJ45 10/100/1000 Mbps Ethernet interface for connecting to the
internet.
Pin assignments and signal name of Ethernet connector
Voltage
Minimum Voltage 11.4V
Maximum Voltage 12.6V
Maximum Current 4.2A
Pin №
RS-232
(Default)
RS-422
RS-485
1
DCD
TxD-
D-
2
RXD
TxD+
D+
3
TXD
RxD+
NC
4
DTR
RxD-
NC
5
GND
GND
GND
6
DSR
NC
NC
7
RTS
NC
NC
8
CTS
NC
NC
9
RI
NC
NC
Pin №
Signal Name
Pin №
Signal Name
1
TX1+
2
TX1-
3
TX2+
4
TX2-
5
TX3+
6
TX3-
7
TX4+
8
TX4-
20
Arm-based Front IP65 HMI User Manual
2.2.4 USB 2.0 Connector
Use USB A Type (USB 2.0) connector to connect your device to other USB 2.0 compatible
devices.
Pin assignments and signal name USB 2.0 connector
2.2.5 USB OTG Connector
Use USB OTG connector to connect the panel PC to other USB On-The-Go compliant devices
such as flash drives, digital cameras, mice or keyboards. Use USB OTG cable to install software
on the panel PC.
Pin assignments and signal name of USB OTG connector
Refer to Ch.5 of this user manual for more details on how to install software
2.2.6 CANBus Connector
Use CANBus connector for the HMI machine-to-machine communication.
Pin assignments and signal name of CANBus connector
*PIN9 default is NC
Pin №
Signal Name
Pin №
Signal Name
1
+5V
2
USB_D-
3
USB_D+
4
GND
Pin №
Signal Name
Pin №
Signal Name
1
+5V
2
USB_OTG_D-
3
USB_OTG_D
+
4
USB_OTG_ID
5
GND
Pin №
Signal Name
Pin №
Signal Name
1
GND
2
CAN_L
3
GND
4
NC
5
NC
6
NC
7
CAN_H
8
GND
9*
+5V/NC
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
Winmate W10FA3S-IPH1HM Manuel utilisateur
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Winmate W10FA3S-IPH1HM User manual
Documents connexes
-
Winmate EL Series Quick Start Manuals
-
Winmate W15FA3S-EHA2 Manuel utilisateur
-
Winmate R15FA3S-PTC3 Guide de démarrage rapide
-
Winmate W15FA3S-EHA2 Manuel utilisateur
-
Winmate W07FA3S-GSM1HB Guide de démarrage rapide
-
Winmate W15FA3S-EHA2 Manuel utilisateur
-
Winmate W07FA3S-PCM1-PoE Manuel utilisateur
-
Winmate W07FA3S-PCM1-PoE Manuel utilisateur
-
Winmate R15FA3S-PCC3-PoE Guide de démarrage rapide
-
Winmate R15FA3S-PCC3-PoE Manuel utilisateur
