DeWalt DCC2560T1DCB606 Manuel utilisateur

Marque: DeWalt

Modèle: DCC2560T1DCB606

Catégorie: Compresseurs d'air

Taper: Manuel utilisateur

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DeWALT

Instruction Manual

Guide D’utilisation

Manual de instrucciones

DCC2560

60V Max* 2.5 Gallon Cordless AirCompressor

Compresseur à air de 9,46l (2,5gal) sans fil (60V Max*)

Compresor de aire inalámbrico de 9,46l (2,5 galones) 60V Máx*

final page size: 8.5 x 5.5 in

ENGLISH

English (original instructions) 1

Français (traduction de la notice d’instructions originale) 14

Español (traducido de las instrucciones originales) 30

Specifications/ Fiche technique/ Especificaciones

Model/ modèle/ modelo DCC2560

Weight/ poids/ peso 21.5 Lbs. (9.75 Kg)/ 9,75 kg (21.5 lbs.)/ 9,75 Kg (21.5 libras)

Height/ hauteur/ altura 15.5" (393.7 mm)/ 393,7 mm (15,5 po)/ 393,7 mm (15,5")

Width/ largeur/ ancho 12.5" (317.5 mm)/ 317,5 mm (12,5 po)/ 317,5 mm (12,5")

Length/ longueur/ longitud 14.0" (355.6 mm)/ 355,6 mm (14,0 po)/ 355,6 mm (14,0")

Air tank capacity/ capacité du réservoir d’air/ capacidad del tanque de aire 2.5 Gallon (9.5 Liters)/ 9,5 liters (2,5 gallons)/ 9,5 (2,5 galones)

Approx cut-in pressure/ pression d’enclenchement approx./ Presión de arranque

aproximada

105 Psi/ 105 psi/ 105 lb/po

Approx. Cut-out pressure/ env. Pression de déclenchement/ presión de corte aprox. 135 Psi/ 135 psi/ 135 lb/po

Scfm @ 90 psi/ pi

/min standard à 90 psi/ scfm a 90 psi

1.2 **/ 1,2 **/ 1,2 **

Noise level/ niveau sonore/ nivel de ruido 79.0 DBA

/ 79,0 dBA

Fuse type/ type de fusible/ fusible de tipo Time delay/ temporisation/ acción retardada

Regulated pressure rating (approximate) / pression nominale stabilisée

(approximative)/ clasificación de presión regulada (aproximadamente)

0–135 Psi/ 0–135 psi/ 0 a 135 lb/po

Quick connect type/ type de raccord à connexion rapide/ tipo de conexión rápida 1/4" (6.4 mm) industrial/ 6,4 mm (1/4 po) industriel/

6,4 mm (1/4") Industrial

Pump Type/ Type de pompe/ Tipo bomba Oilless/ Sans huile/ Sin aceite

**Tested per iso 1217:1996/ testé conformément à la norme iso 1217:1996/probado según la norma iso 1217:1996

+Tested per iso 3744:1994/ testé conformément à la norme iso 3744:1994/probado según la norma iso 3744:1994

ENGLISH

English (original instructions)

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk

of personal injury or property damage.



DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or seriousinjury.



WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or seriousinjury.



CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderateinjury.



(Used without word) Indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in propertydamage.



WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

WARNING: To reduce the risk of injury, read the

instructionmanual.

If you have any questions or comments about this or

any

DeWALT

tool, call us toll free at:

1-800-4-

DeWALT

(1-800-433-9258).

Auto On/Off switch

Battery

Battery release button

Safety valve

Tank pressure gauge

One-turn regulator

Drain valve

Check valve

Quick-connect coupler

Carry handle

Tank

Fig. A

FRONT BACK

4 9

ENGLISH

SAVE ALL WARNINGS AND

INSTRUCTIONS FOR FUTURE

REFERENCE



DANGER: RISK OF EXPLOSION OR FIRE

What can happen How to prevent it

It is normal for electrical contacts

within the motor and pressure

switch to spark.

Always operate the compressor

in a well ventilated area free of

combustible materials, gasoline, or

solvent vapors.

If electrical sparks from compressor

come into contact with flammable

vapors, they may ignite, causing

fire or explosion.

If spraying flammable materials,

locate compressor at least 20 feet

(6.1 m) away from spray area.

An additional length of hose may

be required.

Store flammable materials

in a secure location away

from compressor.

Restricting any of the compressor

ventilation openings will cause

serious overheating and could

cause fire.

Never place objects against or on

top of compressor pump.

Operate compressor in an open

area at least 12" (30.5 cm) away

from any wall or obstruction that

would restrict the flow of fresh air

to the ventilation openings.

Operate compressor in a clean,

dry well ventilated area. Do not

operate unit indoors or in any

confined area.

Unattended operation of this

product could result in personal

injury or property damage.

To reduce the risk of fire, do

not allow the compressor to

operate unattended.

Always remain in attendance with

the product when it is operating.

Always turn off and unplug unit

when not in use.



CAUTION: RISK FROM NOISE

What can happen How to prevent it

Under some conditions and

duration of use, noise from

this product may contribute to

hearing loss.

Always wear certified safety

equipment: ANSI S12.6 (S3.19)

hearing protection.



DANGER: RISK TO BREATHING

(Asphyxiation)

What can happen How to prevent it

The compressed air directly from

your compressor is not safe for

breathing. The air stream may

contain carbon monoxide, toxic

vapors, or solid particles from

the air tank. Breathing these

contaminant's can cause serious

injury or death.

Air obtained directly from the

compressor should never be

used to supply air for human

consumption. In order to use air

produced by this compressor for

breathing, suitable filters and

in-line safety equipment must be

properly installed. In-line filters

and safety equipment used in

conjunction with the compressor

must be capable of treating air

to all applicable local and federal

codes prior to human consumption.

Sprayed materials such as paint,

paint solvents, paint remover,

insecticides, weed killers,

may contain harmful vapors

and poisons.

Work in an area with good cross

ventilation. Read and follow the

safety instructions provided on the

label or safety data sheets for the

materials you are spraying. Always

use certified safety equipment:

OSHA/MSHA/NIOSH respiratory

protection designed for use with

your specific application.



WARNING: RISK OF BURSTING

Air Tank: The air tank on your Air Compressor is designed (for units

with air tanks greater than 6 inch / 152 mm diameter) according to

ASME Section VIII, Div. 1 rules. All pressure vessels should be inspected

once every two years. To find your state pressure vessels inspector, look

under the Division of Labor and Industries in the government section of a

phone book or call 1–800–4-DeWALT for assistance.

The following conditions could lead to a weakening of the air tank, and

result in a violent air tank explosion:

What can happen How to prevent it

Failure to properly drain condensed

water from air tank, causing rust

and thinning of the steel air tank.

Drain air tank daily or after each

use. If air tank develops a leak,

replace it immediately with

a new air tank or replace the

entire compressor.

Modifications or attempted repairs

to the air tank.

Never drill into, weld, or make

any modifications to the air tank

or its attachments. Never attempt

to repair a damaged or leaking air

tank. Replace with a new air tank.

Unauthorized modifications to

the safety valve or any other

components which control air

tank pressure.

The air tank is designed to

withstand specific operating

pressures. Never make adjustments

or parts substitutions to alter the

factory set operating pressures.

Attachments & accessories:

ENGLISH

Exceeding the pressure rating of

air tools, spray guns, air operated

accessories, tires, and other

inflatables can cause them to

explode or fly apart, and could

result in serious injury.

Follow the equipment

manufacturers recommendation

and never exceed the maximum

allowable pressure rating of

attachments. Never use compressor

to inflate small low pressure

objects such as children’s toys,

footballs, basketballs, etc.

Tires:

Over inflation of tires could

result in serious injury and

property damage.

Use a tire pressure gauge to check

the tires pressure before each

use and while inflating tires; see

the tire sidewall for the correct

tire pressure.

NOTE: Air tanks, compressors

and similar equipment used to

inflate tires can fill small tires

similar to these very rapidly. Adjust

pressure regulator on air supply

to no more than the rating of the

tire pressure. Add air in small

increments and frequently use the

tire gauge to prevent over inflation.



WARNING: RISK OF ELECTRICAL SHOCK

What can happen How to prevent it

Your air compressor is powered

by a battery. Like any other direct

current powered device, if it is

not used properly it may cause

electric shock.

Never operate the compressor

outdoors when it is raining or in

wet conditions.

Never operate compressor with

protective covers removed

or damaged.

Repairs attempted by unqualified

personnel can result in serious

injury or death by electrocution.

Any electrical wiring or repairs

required on this product should

be performed by a D

WALT

factory service center or a D

WALT

authorized service center in

accordance with national and local

electrical codes.



WARNING: RISK FROM FLYING OBJECTS

What can happen How to prevent it

The compressed air stream can

cause soft tissue damage to

exposed skin and can propel

dirt, chips, loose particles, and

small objects at high speed,

resulting in property damage or

personal injury.

Always wear certified safety

equipment: ANSI Z87.1 eye

protection (CAN/CSA Z94.3)

with side shields when using

the compressor.

Never point any nozzle or sprayer

toward any part of the body or at

other people or animals.

Always turn the compressor off and

bleed pressure from the air hose

and air tank before attempting

maintenance, attaching tools

or accessories.



WARNING: RISK OF HOT SURFACES

What can happen How to prevent it

Touching exposed metal such as

the compressor head, engine head,

engine exhaust or outlet tubes, can

result in serious burns.

Never touch any exposed metal

parts on compressor during or

immediately after operation.

Compressor will remain hot for

several minutes after operation.

Do not reach around protective

shrouds or attempt maintenance

until unit has been allowed to cool.



WARNING: RISK FROM MOVING PARTS

What can happen How to prevent it

Moving parts such as fans and

connecting rods can cause serious

injury if they come into contact

with you or your clothing.

Never operate the compressor

with guards or covers which are

damaged or removed

Keep your hair, clothing, and

gloves away from moving parts.

Loose clothes, jewelry, or long hair

can be caught in moving parts.

Air vents may cover moving parts

and should be avoided as well.

Attempting to operate compressor

with damaged or missing parts or

attempting to repair compressor

with protective shrouds removed

can expose you to moving parts

and can result in serious injury.

Any repairs required on this

product should be performed by a

WALT factory service center or a

WALT authorized service center.



WARNING: RISK OF UNSAFE OPERATION

What can happen How to prevent it

Unsafe op er a tion of your air

compressor could lead to se ri ous

in ju ry or death to you or others.

Review and understand all

instructions and warnings in

this manual.

Be come fa mil iar with the op eration

and con trols of the air compressor.

Keep operating area clear of all

persons, pets, and obstacles.

Keep chil dren away from the air

compressor at all times.

Do not operate the product when

fatigued or under the influence

of alcohol or drugs. Stay alert at

all times.

Never modify or defeat the safety

features of this product.

Equip area of operation with a

fire extinguisher.

Do not op er ate machine

with missing, broken, or

un authorized parts.

Never stand on the compressor.



WARNING: RISK OF FALLING

ENGLISH

What can happen How to prevent it

A portable compressor can fall

from a table, workbench, or roof

causing damage to the compressor

and could result in serious injury or

death to the operator.

Always operate compressor in a

stable secure position to prevent

accidental movement of the unit.

Never operate compressor on a

roof or other elevated position.

Use additional air hose to reach

high locations.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE



WARNING: This product can expose you to chemicals

including lead which is known to the State of

California to cause cancer and birth defects or other

reproductive harm. For more information go to

www.P65Warnings.ca.gov.



WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to the State

of California to cause cancer, birth defects or

other reproductive harm. Some examples of these

chemicalsare:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-

treatedlumber.

Your risk from these exposures varies, depending on how

often you do this type of work. To reduce your exposure to

these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are

specially designed to filter out microscopicparticles.

• Avoid prolonged contact with dust from power

sanding, sawing, grinding, drilling, and other

construction activities. Wear protective clothing and

wash exposed areas with soap and water. Allowing

dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmfulchemicals.



WARNING: Use of this tool can generate and/

or disperse dust, which may cause serious and

permanent respiratory or other injury. Always use

NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles

away from face andbody.

The label on your tool may include the following symbols. The

symbols and their definitions are asfollows:

V ......................... volts

Hz .......................hertz

min ..................... minutes

or DC ......direct current

...................... Class I Construction

(grounded)

…/min ..............per minute

BPM .................... beats per minute

IPM ..................... impacts per minute

RPM .................... revolutions per

minute

sfpm ................... surface feet per

minute

SPM .................... strokes per minute

A ......................... amperes

W ........................watts

or AC ...........alternating current

or AC/DC .... alternating or

direct current

...................... Class II

Construction

(double insulated)

.......................no load speed

n .........................rated speed

......................earthing terminal

.....................safety alert symbol

.....................visible radiation

..................... wear respiratory

protection

..................... wear eye

protection

..................... wear hearing

protection

..................... read all

documentation

BATTERIES AND CHARGERS

The battery pack is not fully charged out of the carton.

Before using the battery pack and charger, read the

safety instructions below and then follow charging

proceduresoutlined. When ordering replacement battery

packs, be sure to include the catalog number andvoltage.

Your tool uses a

DeWALT

charger. Be sure to read all safety

instructions before using your charger. Consult the chart

at the end of this manual for compatibility of chargers and

batterypacks.

READ ALL INSTRUCTIONS

Important Safety Instructions for All

Battery Packs



WARNING: Read all safety warnings and all

instructions for the battery pack, charger and

power tool. Failure to follow the warnings and

instructions may result in electric shock, fire and/

or seriousinjury.

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Inserting or removing the battery

pack from the charger may ignite the dust orfumes.

• NEVER force the battery pack into the charger. DO

NOT modify the battery pack in any way to fit into

a non-compatible charger as battery pack may

rupture causing serious personal injury. Consult

the chart at the end of this manual for compatibility of

batteries andchargers.

• Charge the battery packs only in designated

DeWALT

chargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or

exceed 104°F (40°C) (such as outside sheds or metal

buildings in summer). For best life store battery packs in

a cool, drylocation.

NOTE: Do not store the battery packs in a tool with

the trigger switch locked on. Never tape the trigger

switch in the ONposition.

• Do not incinerate the battery pack even if it is

severely damaged or is completely worn out. The

battery pack can explode in a fire. Toxic fumes and

materials are created when lithium ion battery packs

areburned.

ENGLISH

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open

eye for 15 minutes or until irritation ceases. If medical

attention is needed, the battery electrolyte is composed of

a mixture of liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause

respiratory irritation. Provide fresh air. If symptoms

persist, seek medicalattention.



WARNING: Burn hazard. Battery liquid may be

flammable if exposed to spark orflame.



WARNING: Fire hazard. Never attempt to open the

battery pack for any reason. If the battery pack case

is cracked or damaged, do not insert into the charger.

Do not crush, drop or damage the battery pack. Do

not use a battery pack or charger that has received a

sharp blow, been dropped, run over or damaged in

any way (e.g., pierced with a nail, hit with a hammer,

stepped on). Damaged battery packs should be

returned to the service center forrecycling.

Transportation



WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do

not place the battery pack in aprons, pockets, tool

boxes, product kit boxes, drawers, etc., with loose

nails, screws, keys, etc. Transporting batteries

can possibly cause fires if the battery terminals

inadvertently come in contact with conductive

materials such as keys, coins, hand tools and the

like. The US Department of Transportation Hazardous

Material Regulations (HMR) actually prohibit

transporting batteries in commerce or on airplanes in

carry-on baggage UNLESS they are properly protected

from short circuits. So when transporting individual

battery packs, make sure that the battery terminals

are protected and well insulated from materials that

could contact them and cause a shortcircuit.

Shipping the

DeWALT

FLEXVOLT™ Battery

The D

WALT FLEXVOLT™ battery has two modes: Use and

Shipping.

Use Mode: When the FLEXVOLT™ battery stands alone or is

in a D

WALT 20V Max* product, it will operate as a 20V Max*

battery. When the FLEXVOLT™ battery is in a 60V Max* or a

120V Max* (two 60V Max* batteries) product, it will operate

as a 60V Max* battery.

Shipping Mode: When

the cap is attached to the

FLEXVOLT™ battery, the

battery is in Shipping Mode.

Strings of cells are electrically

disconnected within the pack resulting in three batteries

with a lower Watt hour (Wh) rating as compared to one

battery with a higher Watt hour rating. This increased

quantity of three batteries with the lower Watt hour rating

can exempt the pack from certain shipping regulations that

are imposed upon the higher Watt hourbatteries.

The battery label indicates two Watt hour ratings (see

example). Depending on how the battery is shipped, the

appropriate Watt hour rating must be used to determine

the applicable shipping requirements. If utilizing the

shipping cap, the pack will be considered 3 batteries at

the Watt hour rating indicated for “Shipping”. If shipping

without the cap or in a tool, the pack will be considered one

battery at the Watt hour rating indicated next to “Use”.

USE: 120 Wh Shipping: 3 x 40 Wh

Example of Use and Shipping Label Marking

For example, Shipping Wh rating might indicate 3 x 40 Wh,

meaning 3 batteries of 40 Watt hours each. The Use Wh

rating might indicate 120 Wh (1 battery implied).

Fuel Gauge Battery Packs (Fig. B)

Some

DeWALT

battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

The fuel gauge is an indication of approximate levels of

charge remaining in the battery pack according to the

followingindicators:

75–100% charged

51–74% charged

< 50% charged

Pack needs to be charged

To actuate the fuel gauge, press and hold the fuel gauge

button. A combination of the three green LED lights will

illuminate designating the level of charge left. When the

level of charge in the battery is below the usable limit, the

fuel gauge will not illuminate and the battery will need to

berecharged.

Fig. B

NOTE: The fuel gauge is only an indication of the charge left

on the battery pack. It does not indicate tool functionality

and is subject to variation based on product components,

temperature and end-userapplication.

For more information regarding fuel gauge battery packs,

please contact call 1-800-4-

DeWALT

(1-800-433-9258) or

visit our website www.dewalt.com.

The RBRC® Seal

The RBRC® (Rechargeable Battery

Recycling Corporation) Seal on the nickel

cadmium, nickel metal hydride or lithium-

ion batteries (or battery packs) indicates

that the costs to recycle these batteries

(or battery packs) at the end of their useful life have already

been paid by

DeWALT

. In some areas, it is illegal to place

spent nickel cadmium, nickel metal hydride or lithium-ion

batteries in the trash or municipal solid waste stream and

ENGLISH

the Call2Recycle® program provides an environmentally

consciousalternative.

Call 2 Recycle, Inc., in cooperation with

DeWALT

and other

battery users, has established the program in the United

States and Canada to facilitate the collection of spent nickel

cadmium, nickel metal hydride or lithium-ion batteries. Help

protect our environment and conserve natural resources by

returning the spent nickel cadmium, nickel metal hydride

or lithium-ion batteries to an authorized

DeWALT

service

center or to your local retailer for recycling. You may also

contact your local recycling center for information on

where to drop off the spent battery. RBRC® is a registered

trademark of Call 2 Recycle,Inc.

Important Safety Instructions for All

Battery Chargers



WARNING: Read all safety warnings and all

instructions for the battery pack, charger and

power tool. Failure to follow the warnings and

instructions may result in electric shock, fire and/

or seriousinjury.

• DO NOT attempt to charge the battery pack with

any chargers other than the ones in this manual.

The charger and battery pack are specifically designed to

worktogether.

• These chargers are not intended for any uses other

than charging

DeWALT

rechargeable batteries.

Any other uses may result in risk of fire, electric shock

orelectrocution.

• Do not expose the charger to rain orsnow.

• Pull by the plug rather than the cord when

disconnecting the charger. This will reduce the risk of

damage to the electric plug andcord.

• Make sure that the cord is located so that it will not

be stepped on, tripped over or otherwise subjected

to damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in

risk of fire, electric shock orelectrocution.

• When operating a charger outdoors, always provide

a dry location and use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electricshock.

• An extension cord must have adequate wire size

(AWG or American Wire Gauge) for safety. The smaller

the gauge number of the wire, the greater the capacity

of the cable, that is, 16 gauge has more capacity than 18

gauge. An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. When using

more than one extension to make up the total length,

be sure each individual extension contains at least the

minimum wire size. The following table shows the correct

size to use depending on cord length and nameplate

ampere rating. If in doubt, use the next heavier gauge. The

lower the gauge number, the heavier thecord.

Minimum Gauge for Cord Sets

Volts Total Length of Cord in Feet (meters)

120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Ampere Rating

American Wire Gauge

Than

Not

Than

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or

place the charger on a soft surface that might block

the ventilation slots and result in excessive internal

heat. Place the charger in a position away from any heat

source. The charger is ventilated through slots in the top

and the bottom of thehousing.

• Do not operate the charger with a damaged cord

orplug.

• Do not operate the charger if it has received a sharp

blow, been dropped or otherwise damaged in any

way. Take it to an authorized servicecenter.

• Do not disassemble the charger; take it to an

authorized service center when service or repair

is required. Incorrect reassembly may result in a risk of

electric shock, electrocution orfire.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect 2 chargerstogether.

• The charger is designed to operate on standard

120V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.



WARNING: Shock hazard. Do not allow any liquid to

get inside the charger. Electric shock mayresult.



WARNING: Burn hazard. Do not submerge the

battery pack in any liquid or allow any liquid to

enter the battery pack. Never attempt to open the

battery pack for any reason. If the plastic housing of

the battery pack breaks or cracks, return to a service

center forrecycling.



CAUTION: Burn hazard. To reduce the risk of injury,

charge only

DeWALT

rechargeable battery packs.

Other types of batteries may overheat and burst

resulting in personal injury and propertydamage.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the charger can

be shorted by foreign material. Foreign materials

of a conductive nature, such as, but not limited to,

grinding dust, metal chips, steel wool, aluminum

foil or any buildup of metallic particles should be

kept away from the charger cavities. Always unplug

the charger from the power supply when there is no

battery pack in the cavity. Unplug the charger before

attempting toclean.

ENGLISH

Wireless Certifications and Safety

Information

• This device is CAN ICES-3(B)/NMB-3(B)compliant.

• This device complies with Part 15 of the FCC rules and

Industry Canada License-exempt RSS standard(s).

Operation is subject to the following two conditions:

ʵ This device may not cause harmful interference, and

ʵ This device must accept any interference

received, including interference that may cause

undesiredoperation.

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the

followingmeasures:

ʵ Reorient or relocate the receivingantenna.

ʵ Increase the separation between the equipment

andadaptor.

ʵ Connect the equipment into an outlet on a circuit

different from that to which the adaptor isconnected.

ʵ Consult the dealer or an experienced radio/TV

technician forhelp.

• Changes or modifications to this equipment not expressly

approved by the manufacturer could void the user’s

authority to operate the device. This Class B digital

apparatus complies with Canadian ICES-003.

• Under Industry Canada regulations, this radio transmitter

may only operate using an antenna of a type and

maximum (or lesser) gain approved for the transmitter by

Industry Canada. To reduce potential radio interference

to other users, the antenna type and its gain should

be so chosen that the equivalent isotropically radiated

power (e.i.r.p.) is not more than that necessary for

successfulcommunication.

• To comply with FCC and Industry Canada RF radiation

exposure limits for general population, the antenna used

for this device must not be co-located or operating in

conjunction with any other antenna ortransmitter.

For Bluetooth® Products

• When traveling on airlines, be sure to comply with the

airline restrictions on usage of personal electronic devices

and Bluetooth®.

• The out of range alert feature has been designed to act

as an aid to warn against products getting misplaced or

stolen. It is not a securitysystem.

• The connectivity range is up to 100 feet (30.5 meters)

depending on environment andlocation.

• The shortwave radio frequency signals of a Bluetooth®

device may impair the operation of other electronic and

medical devices (such as pacemakers or hearing aids).

NOTE: The Bluetooth® word mark and logos are registered

trademarks owned by the Bluetooth®, SIG, Inc. and any use of

such marks by

DeWALT

is under license. Other trademarks and

trade names are those of their respectiveowners.

This product complies with these standards when operated

with a 6 foot (1.8 meters) or shorter extensioncord.

Charging a Battery (Fig. C)

1. Plug the charger into an appropriate outlet before

inserting batterypack.

Fig. C

2. Insert the battery pack

2

into the charger, making sure

the battery pack is fully seated in the charger. The red

(charging) light will blink continuously indicating that

the charging process hasstarted.

3. The completion of charge will be indicated by the red

light remaining ON continuously. The battery pack is

fully charged and may be used at this time or left in the

charger. To remove the battery pack from the charger,

push the battery release button

3

on the batterypack.

NOTE: To ensure maximum performance and life of lithium-

ion battery packs, charge the battery pack fully before

firstuse.

Charger Operation

Refer to the indicators below for the charge status of the

batterypack.

DCB107, DCB112, DCB113, DCB115, DCB118, DCB132

Charging

Fully Charged

Hot/Cold Pack Delay*

* DCB107, DCB112, DCB113, DCB115, DCB118, DCB132:

The red light will continue to blink, but a yellow indicator

light will be illuminated during this operation. Once the

battery pack has reached an appropriate temperature, the

yellow light will turn off and the charger will resume the

chargingprocedure.

The compatible charger(s) will not charge a faulty battery

pack. The charger will indicate faulty battery pack by

refusing to light or by displaying a problem pack or charger

blinkpattern.

NOTE: This could also mean a problem with acharger.

ENGLISH

If the charger indicates a problem, take the charger and

battery pack to be tested at an authorized servicecenter.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot

or too cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery pack has reached an

appropriate temperature. The charger then automatically

switches to the pack charging mode. This feature ensures

maximum battery packlife.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery packwarms.

The DCB118 charger is equipped with an internal fan

designed to cool the battery pack. The fan will turn on

automatically when the battery pack needs to becooled.

Never operate the charger if the fan does not operate

properly or if ventilation slots are blocked. Do not permit

foreign objects to enter the interior of thecharger.

Electronic Protection System

Li-Ion tools are designed with an Electronic Protection

System that will protect the battery pack against

overloading, overheating or deepdischarge.

The tool will automatically turn off if the Electronic

Protection System engages. If this occurs, place the lithium-

ion battery pack on the charger until it is fullycharged.

Wall Mounting

DCB107, DCB112, DCB113, DCB115, DCB118, DCB132

These chargers are designed to be wall mountable or to

sit upright on a table or work surface. If wall mounting,

locate the charger within reach of an electrical outlet,

and away from a corner or other obstructions which may

impede air flow. Use the back of the charger as a template

for the location of the mounting screws on the wall. Mount

the charger securely using drywall screws (purchased

separately) at least 1" (25.4 mm) long, with a screw head

diameter of 0.28–0.35" (7–9mm), screwed into wood to an

optimal depth leaving approximately 7/32" (5.5 mm) of the

screw exposed. Align the slots on the back of the charger

with the exposed screws and fully engage them in theslots.

Charger Cleaning Instructions



WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using

a cloth or soft non-metallic brush. Do not use water or

any cleaningsolutions.

Important Charging Notes

1. Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

between 65°F and 75°F (18° – 24°C). DO NOT charge

the battery pack in an air temperature below +40°F

(+4.5°C), or above +104°F (+40°C). This is important

and will prevent serious damage to the batterypack.

2. The charger and battery pack may become warm to the

touch while charging. This is a normal condition, and

does not indicate a problem. To facilitate the cooling of

the battery pack after use, avoid placing the charger or

battery pack in a warm environment such as in a metal

shed or an uninsulatedtrailer.

3. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp

or other appliance;

b. Check to see if receptacle is connected to a light

switch which turns power off when you turn out the

lights;

c. Move the charger and battery pack to a location

where the surrounding air temperature is

approximately 65°F – 75°F (18° – 24°C);

d. If charging problems persist, take the tool, battery

pack and charger to your local servicecenter.

4. The battery pack should be recharged when it fails to

produce sufficient power on jobs which were easily

done previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may

also charge a partially used pack whenever you desire

with no adverse effect on the batterypack.

5. Foreign materials of a conductive nature such as, but

not limited to, grinding dust, metal chips, steel wool,

aluminum foil, or any buildup of metallic particles

should be kept away from charger cavities. Always

unplug the charger from the power supply when there

is no battery pack in the cavity. Unplug the charger

before attempting toclean.

6. Do not freeze or immerse the charger in water or any

otherliquid.

Storage Recommendations

1. The best storage place is one that is cool and dry, away

from direct sunlight and excess heat orcold.

2. For long storage, it is recommended to store a fully

charged battery pack in a cool dry place out of the

charger for optimalresults.

NOTE: Battery packs should not be stored completely

depleted of charge. The battery pack will need to be

recharged beforeuse.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

COMPONENTS (FIG. A)



WARNING: Never modify the power tool or any part

of it. Damage or personal injury couldresult.

Refer to Figure A at the beginning of this manual for a

complete list ofcomponents.

Intended Use

Your compressor is designed for professional finish nailing

and staplingapplications.

DO NOT use under wet conditions or in presence of

flammable liquids orgases.

Your compressor is a professional power tool. DO NOT let

children come into contact with the tool. Supervision is

required when inexperienced operators use thistool.

ENGLISH

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.

How To Set Up Your Unit

Unpacking

Remove unit from carton and discard allpackaging.

Location of the Air Compressor

• Locate the air compressor in a clean, dry and well

ventilatedarea.

• The air compressor should be located at least 12"

(30.5 cm) away from the wall or other obstructions that

will interfere with the flow ofair.

• The air compressor pump and shroud are designed

to allow for proper cooling. The ventilation openings

on the compressor are necessary to maintain proper

operating temperature. Do not place rags or other

containers on or near theseopenings.

OPERATION



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.

Installing and Removing the Battery Pack

(Fig. D)

NOTE: For best results, make sure your battery pack is

fullycharged.

To install the battery pack

2

into the tool handle, align the

battery pack with the rails inside the tool’s handle and slide

it into the handle until the battery pack is firmly seated in

the tool and ensure that it does notdisengage.

To remove the battery pack from the tool, press the release

button

3

and firmly pull the battery pack out of the tool

handle. Insert it into the charger as described in the charger

section of thismanual.

Fig. D

Know Your Air Compressor

READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE

OPERATING YOUR UNIT. Compare the illustrations with

your unit to familiarize yourself with the location of

various controls and adjustments. Save this manual for

futurereference.

Description of Operation (Fig. A)

Become familiar with these controls before operating

theunit.

Auto On(I)/Off(O) Switch

1

: Place this switch in the

"AutoOn" position to provide automatic power to the

pressure switch and "Off" to remove power at the end of

eachuse.

Pressure Switch (not shown): The pressure switch

automatically starts the motor when the air tank pressure

drops below the factory set "cut-in" pressure. It stops the

motor when the air tank pressure reaches the factory set

"cut-out"pressure.

Safety Valve

4

: If the pressure switch does not shut off the

air compressor at its "cut-out" pressure setting, the safety

valve will protect against high pressure by "popping out"

at its factory set pressure (slightly higher than the pressure

switch "cut-out" setting).

Tank Pressure Gauge

5

: The tank pressure gauge

indicates the reserve air pressure in thetank.

One-Turn Regulator

6

: Controls the air pressure available

at the quick-connect outlet. Turn regulator clockwise to

increase pressure or counterclockwise to decrease pressure.

Stop when indicator matches with desired outlet pressure.

Cooling System (not shown): This compressor contains

an advanced design cooling system. At the heart of this

cooling system is an engineered fan. It is perfectly normal

for this fan to blow air through the vent holes in large

amounts. You know that the cooling system is working

when air is beingexpelled.

Air Compressor Pump (not shown): Compresses air into

the air tank. Working air is not available until the compressor

has raised the air tank pressure above that required at the

airoutlet.

Drain Valve

7

: The drain valve is located at the base of

the air tank and is used to drain condensation at the end of

eachuse.

Check Valve

8

: When the air compressor is operating,

the check valve is "open", allowing compressed air to enter

the air tank. When the air compressor reaches "cut-out"

pressure, the check valve "closes", allowing air pressure to

remain inside the airtank.

Motor Overload Protector (not shown): The motor has

a thermal overload protector. If the motor overheats for any

reason, the overload protector will shut off the motor. The

motor must be allowed to cool down before restarting. To

restart:

1. Set the Auto On/Off switch to "Off".

2. Remove thebattery.

3. Allow the motor tocool.

4. Replace thebattery.

ENGLISH

5. Set the Auto On/Off switch to "Auto On"position.

Quick-Connect Coupler

9

: The quick connect body

accepts industrial quick connectplugs.

How to Use Your Unit (Fig. E)

How to Stop

1. Set the Auto On/Off switch

1

to "Off".

2. Remove battery when not in use.

Before Starting



WARNING: Do not operate this unit until you read

this instruction manual for safety, operation and

maintenanceinstructions.

Before Each Start-Up

1. Remove battery. (Refer to Installing and Removing

the Battery Pack)

2. Set the Auto On/Off switch

1

to "Off".

3. Turn the regulator

6

counterclockwise to set the outlet

pressure to zero.

4. Attach hose andaccessories.



WARNING: Risk of unsafe operation. Firmly grasp

air hose in hand when installing or disconnecting

to prevent hosewhip.



WARNING: Risk of unsafe operation. Do not use

damaged or wornaccessories.

NOTE: The hose or accessory will require a quick connect

plug if the air outlet is equipped with a quick connect

body

9



WARNING: Risk of Bursting. Too much air pressure

causes a hazardous risk of bursting. Check the

manufacturer’s maximum pressure rating for air tools

and accessories. The regulator outlet pressure must

never exceed the maximum pressurerating.

NOTICE: Risk of property damage. Compressed air

from the unit may contain wa ter condensation and

oil mist. Do not spray un fil tered air at an item that

could be damaged by moisture. Some air tools and

accessories may require filtered air. Read the in struc-

tions for the air tools andaccessories.

How to Start

1. Install the battery into thetool.

2. Set the Auto On/Off switch

1

to "Auto On" and allow

tank pressure to build. Motor will stop when tank

pressure reaches "cut-out"pressure.

3. Turn regulator

6

clockwise to increase pressure and

stop when desired pressure isreached.



WARNING: Risk of unsafe operation. If any

unusual noise or vibration is noticed, stop the

compressor immediately and have it checked by

a trained servicetechnician.



WARNING: Ensure the regulator is set to a pressure

lower than the maximum operating pressure of

thetool.

The compressor is ready foruse.

Fig. E

4 9

MAINTENANCE



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.

Customer Responsibilities

Before each

use

Daily or after

each use

See tank

warning label

Check Safety Valve X

Drain Tank X

Remove tank from service X

***

*** For more information, call 1–800–4-

DeW

ALT (1–800–433–9258)



WARNING: Risk of unsafe operation. Unit cycles

automatically when power is on.

When performing maintenance, you may be exposed

to voltage sources, compressed air, or moving parts.

Personal injuries can occur. Before performing any

maintenance or repair, disconnect power source from

the compressor and bleed off all airpressure.

NOTE: See Operation section for the location ofcontrols.

To Check Safety Valve (Fig. E)



WARNING: Risk of Bursting. If the safety valve does

not work properly, over-pressurization may occur,

causing air tank rupture or anexplosion.



WARNING: Risk from Flying Objects. Always wear

certified safety equipment: ANSI Z87.1 eye protection

(CAN/CSA Z94.3) with sideshields.

Before starting compressor, pull the ring on the safety

valve

4

to make sure that the safety valve operates freely. If

the valve is stuck or does not operate smoothly, it must be

replaced with the same type ofvalve.

ENGLISH

Fig. F

To Drain Tank (Fig. E, F)



WARNING: Risk of Unsafe Operation. Air tanks

contain high pressure air. Keep face and other body

parts away from outlet of drain. Use ANSI Z87.1 eye

protection (CAN/CSA Z94.3) when draining as debris

can be kicked up intoface.



WARNING: Risk from noise. Always wear proper

hearing protection during use. Under some conditions

and duration of use, noise from this product may

contribute to hearingloss.

NOTE: All compressed air systems generate condensate

that accumulates in any drain point (e.g., tanks, filter,

aftercoolers, dryers). This condensate contains lubricating

oil and/or substances which may be regulated and must be

disposed of in accordance with local, state, and federal laws

andregulations.



WARNING: Risk of Bursting. Water will condense in

the air tank. If not drained, water will corrode and

weaken the air tank causing a risk of air tankrupture.

NOTICE: Risk of Property Damage. Drain water

from air tank may contain oil and rust which can

causestains.

1. Set the On/Off switch

1

to "Off".

2. Remove thebattery.

3. Turn the regulator

6

counterclockwise to set the outlet

pressure tozero.

4. Remove the air tool oraccessory.

5. Place a suitable container under the drain valve to

catchdischarge.

6. Pull ring on safety valve

4

allowing air to bleed from

the tank until tank pressure is approximately 20 psi.

Release safety valvering.

7. Drain water from air tank by opening drain valve

7

bottom oftank.

8. After the water has been drained, close the drain valve.

The air compressor can now bestored.

NOTE: If drain valve is plugged, release all air pressure

by connecting a tool the the airline and operating it until

tank pressure is zero psi. The valve can then be removed,

cleaned, thereinstalled.

Storage

Before you store the air compressor, make sure you do the

following:

1. Review the Maintenance section on the preceding

pages and perform scheduled maintenance

asnecessary.

2. Always toggle Auto On/Off Switch to "Off" and remove

battery. Drain water from air tank. See To Drain Tank

underMaintenance.



WARNING: Water will condense in the air tank. If

not drained, water will corrode and weaken the

air tank causing a risk of air tankrupture.

3. Store the air compressor in a clean and drylocation.

Accessories



WARNING: Since accessories, other than those

offered by

DeWALT

, have not been tested with this

product, use of such accessories with this tool could be

hazardous. To reduce the risk of injury, only

DeWALT

recommended accessories should be used with

thisproduct.

Recommended accessories for use with your tool

are available at extra cost from your local dealer or

authorized service center. If you need assistance in

locating any accessory, please contact

DeWALT

Industrial

Tool Co., 701East Joppa Road, Towson, MD 21286, call

1-800-4-

DeWALT

(1-800-433-9258) or visit our website:

www.dewalt.com.

Cleaning



WARNING: Blow dirt and dust out of all air vents with

clean, dry air at least once a week. To minimize the risk

of eye injury, always wear ANSI Z87.1 approved eye

protection when performingthis.



WARNING: Never use solvents or other harsh

chemicals for cleaning the non-metallic parts of

the tool. These chemicals may weaken the plastic

materials used in these parts. Use a cloth dampened

only with water and mild soap. Never let any liquid

get inside the tool; never immerse any part of the tool

into aliquid.

Repairs

The charger and battery pack are notserviceable.



WARNING: To assure product SAFETY and

RELIABILITY, repairs, maintenance and adjustment

(including brush inspection and replacement, when

applicable) should be performed by a

DeWALT

factory

service center or a

DeWALT

authorized service center.

Always use identical replacementparts.

Service Information

Please have the following information available for all

service calls:

Model Number _______________________________

Serial Number ________________________________

Date and Place of Purchase _______________________

ENGLISH

Thank you for your purchase. Register your product nowfor:

• WARRANTY SERVICE: Registering your product will

help you obtain more efficient warranty service in case

there is a problem with yourproduct.

• CONFIRMATION OF OWNERSHIP: In case of

an insurance loss, such as fire, flood or theft, your

registration of ownership will serve as your proof

ofpurchase.

• FOR YOUR SAFETY: Registering your product will

allow us to contact you in the unlikely event a safety

notification is required under the Federal Consumer

SafetyAct.

Three Year Limited Warranty

DeWALT

will repair, without charge, any defects due to

faulty materials or workmanship for three years from

the date of purchase. This warranty does not cover part

failure due to normal wear or tool abuse. For further detail

of warranty coverage and warranty repair information,

visit www.dewalt.com or call 1-800-4-

DeWALT

(1-800-

433-9258). This warranty does not apply to accessories

or damage caused where repairs have been made

or attempted by others. THIS LIMITED WARRANTY IS

GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED

WARRANTY OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL

OR CONSEQUENTIAL DAMAGES. Some states do not allow

limitations on how long an implied warranty lasts or the

exclusion or limitation of incidental or consequential

damages, so these limitations may not apply to you. This

warranty gives you specific legal rights and you may have

other rights which vary in certain states orprovinces.

In addition to the warranty,

DeWALT

tools are covered

byour:

1 YEAR FREE SERVICE

DeWALT

will maintain the tool and replace worn parts

caused by normal use, for free, any time during the first year

afterpurchase.

2 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DC9071, DC9091, DC9096, DC9182, DC9280, DC9360, DCB120,

DCB127, DCB201, DCB203, DCB203BT, DCB207, DCB361

3 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DCB200, DCB204, DCB204BT, DCB205, DCB205BT, DCB206,

DCB606, DCB609

NOTE: Battery warranty voided if the battery pack is

tampered with in any way.

DeWALT

is not responsible

for any injury caused by tampering and may prosecute

warranty fraud to the fullest extent permitted bylaw.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of

your

DeWALT

Power Tool, Laser, or Nailer for any reason, you

can return it within 90 days from the date of purchase with

a receipt for a full refund – no questionsasked.

LATIN AMERICA: This warranty does not apply to products

sold in Latin America. For products sold in Latin America,

see country specific warranty information contained in

the packaging, call the local company or see website for

warrantyinformation.

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1-800-4-

DeWALT

(1-800-433-9258) for a freereplacement.

GLOSSARY

CFM: Cubic feet perminute.

SCFM: Standard cubic feet per minute; a unit of measure of

airdelivery.

PSI: Pounds per square inch; a unit of measure ofpressure.

kPa (kilopascal): Metric pressure measurement. 1

kilopascal equal 1000pascals.

Code Certification: Products that bear one or more of

the following marks: UL®, CUL, CULUS, ETL®, CETL, CETLUS,

have been evaluated by OSHA certified independent safety

laboratories and meet the applicable Standards forSafety.

UL® is a registered trademark of Underwriters Laboratories

and ETL® is a registered trademark of Electrical

TestingLaboratories.

Cut-In Pressure: While the motor is off, air tank pressure

drops when accessory is used. When the tank pressure

drops to a certain low level the motor will restart

automatically. The low pressure at which the motor

automatically restarts is called cut-inpressure.

Cut-Out Pressure: When an air compressor is turned on

and begins to run, air pressure in the air tank begins to

build. It builds to a certain high pressure before the motor

automatically shuts off, protecting your air tank from

pressure higher than its capacity. The high pressure at which

the motor shuts off is called cut-outpressure.

Duty Cycle: This air compressor pump is capable of running

continuously. However, to prolong the life of your air

compressor, it is recommended that a 50%-75% average

duty cycle be maintained; that is, the air compressor pump

should not run more than 30–45 minutes in any givenhour.

Declared Noise Emission Values

per ISO 3744

Noise Emission Values

Sound Pressure Level: LpA = 79.0 dBA re 20μPA

Uncertainty in the Sound Pressure Level: KpA = 3.0 dBA re 20μPA

Sound Power Level: LwA = 91.5 dBA re 1 pw

Uncertainty in the Sound Power Level: KwA = 3.0 dBA re 1 pw

The sum of the emission value and the uncertainty is the

limit below which there is a 95% confidence the value of a

single tool will lie below when the tool isnew.

ENGLISH

Troubleshooting Guide

This section provides a list of the more frequently encountered malfunctions, their causes and corrective actions. The

operator or maintenance personnel can perform some corrective actions, and others may require the assistance of a

qualified

DeWALT

technician or yourdealer.

Code Possible Cause Possible Solution

Pressure switch does not shut off

motor when compressor reaches cut-

out pressure

Set the Auto On/Off switch to "Off" and remove the batttery, if the unit does not shut off contact a

WALT factory service center or a D

WALT authorized service center.

2 Pressure switch cut-out too high Contact a D

WALT factory service center or a D

WALT authorized service center.

Tube fittings are not tight enough Tighten fittings where air can be heard escaping. Check fittings with soapy water solution. Do

NotOvertighten.

Defective air tank Air tank must be replaced. Do not repair the leak.



WARNING: Risk of bursting. Do not drill into, weld or otherwise modify

air tank or it will weaken. The air tank can rupture orexplode.

Leaking seals Contact a D

WALT factory service center or a D

WALT authorized service center.

Defective safety valve Operate safety valve manually by pulling on ring. If valve still leaks, it must be replaced.

Regulator is not adjusted correctly for

accessory being used

It is normal for some pressure drop to occur when an accessory is used, adjust the regulator as

instructed in One-turn Regulator under Description of Operations if pressure drop is excessive.

NOTE: Adjust the regulated pressure under flow conditions while accessory is being used.

8 Prolonged excessive use of air Decrease amount of air usage.

Compressor is not large enough for

accessory

Check the accessory air requirement. If it is higher than the CFM or pressure supplied by your air

compressor, a larger compressor is needed to operate accessory.

11 Check valve restricted Contact a D

WALT factory service center or a D

WALT authorized service center.

12 Air leaks Tighten fittings.

Regulator is damaged Replace.

Motor overload protection switch has

tripped

Refer to Motor Overload Protector under Description of Operations. If motor overload protection

trips frequently, contact a D

WALT factory service center or a D

WALT authorized service center.

Tank pressure exceeds pressure switch

cut-in pressure

Motor will start automatically when tank pressure drops below cut-in pressure of pressure switch.

Loose electrical connections Contact a D

WALT factory service center or a D

WALT authorized service center.

Possible defective motor Contact a D

WALT factory service center or a D

WALT authorized service center.

Paint spray on internal motor parts Contact a D

WALT factory service center or a D

WALT authorized service center. Do not operate the

compressor in the paint spray area. See flammable vapor warning.

Pump does not run because tank

pressure is above cut-in pressure.

Drain tank to below cut-in pressure when pump turns on.

Pump does not run due to safety fault. Cycle Auto On/Off Switch from "Off" to "Auto On."

Troubleshooting Codes

Problem Code

Excessive air tank pressure-safety valve pops off 1, 2

Air leaks 3

Air leaks in air tank or at air tank welds 4

Air leaks between head and valve plate 5

Air leaks from safety valve 6

Compressor is not supplying enough air to operate accessories 7, 8, 9, 10, 11, 12

Regulator knob has continuous air leak 13

Regulator will not shut off air outlet 13

Motor will not run 6, 14, 15, 16, 17, 18, 19, 20

FRANÇAIS

Définitions : symboles et termes d'alarmes sécurité

Ces guides d'utilisation utilisent les symboles et termes d'alarmes sécurité suivants pour vous prévenir de situations

dangereuses et de risques de dommages corporels ou matériels.



DANGER: indique une situation dangereuse imminente qui, si elle n’est pas évitée, entraînera la mort ou des

blessuresgraves.



AVERTISSEMENT: indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner la

mort ou des blessuresgraves.



ATTENTION: indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner des

blessures légères oumodérées.



(Si utilisé sans aucun terme) Indique un message propre à la sécurité.

AVIS : indique une pratique ne posant aucun risque de dommages corporels mais qui par contre, si rien n’est fait

pour l’éviter, pourrait poser des risques de dommages matériels.



AVERTISSEMENT! lire tous les avertissements de

sécurité et toutes les directives. Le non-respect

des avertissements et des directives pourrait se

solder par un choc électrique, un incendie et/ou une

blessuregrave.

AVERTISSEMENT : afin de réduire le risque de

blessures, lire le mode d’emploi del’outil.

Pour toute question ou remarque au sujet de cet outil

ou de tout autre outil

DeWALT

, composez le numéro

sans frais : 1-800-4-

DeWALT

(1-800-433-9258).

Commutateur Marche/Arrêt automatique

Bloc-piles

Bouton de libération du bloc-piles

Soupape de sûreté

Manomètre du réservoir

Régulateur de pression à un seul tour

Robinet de vidange

Clapet de non-retour

Raccord de connexion rapide

Poignée de transport

Réservoir

Français (traduction de la notice d’instructions originale)

Fig. A

FAÇADE DOS

4 9

FRANÇAIS

CONSERVER TOUS LES

AVERTISSEMENTS ET TOUTES

LES DIRECTIVES POUR UN USAGE

ULTÉRIEUR



DANGER : RISQUE D’EXPLOSION

OU D’INCENDIE

Ce qui peut se produire Comment l’Éviter

Il est normal que des contacts

électriques dans le moteur

et le manocontacteur fassent

une étincelle.

Faites toujours fonctionner le

compresseur dans une zone bien

aérée sans matière combustible,

essence ou vapeur de solvant.

Si une étincelle électrique

provenant du compresseur

entre en contact avec des

vapeurs inflammables, elle peut

s’enflammer et causer un incendie

ou une explosion.

Si vous aspergez des matériaux

inflammables, placez le

compresseur à au moins 6,1 m

(20 pieds) de la zone pulvérisée.

Il est possible que vous ayez

besoin d’une longueur de

tuyau additionnelle.

Entreposez les matières

inflammables dans un

endroit sécuritaire, éloigné

du compresseur.

Le fait de limiter les ouvertures

d’aération de compresseur causera

une importante surchauffe et

pourrait causer un incendie.

Ne jamais placer d'objets contre

la pompe du compresseur ou sur

celle-ci.

Faites fonctionner le compresseur

dans un endroit aéré à au moins

30,5 cm (12 po) du mur ou de

l’obstruction qui pourrait limiter le

débit d’air frais dans les ouvertures

d’aération.

Faites fonctionner le compresseur

dans un endroit propre, sec et bien

aéré. Ne pas utiliser l’appareil à

l’intérieur ou dans un endroit exigu.

Le fonctionnement de ce produit

sans surveillance pourrait se solder

par des blessures personnelles ou

des dommages à la propriété. Afin

de réduire le risque d’incendie,

ne pas laisser le compresseur

fonctionner sans surveillance.

Être toujours présent lorsque le

produit est en marche.

Toujours éteindre et débrancher

l'appareil si non utilisé.



ATTENTION : RISQUE ASSOCIÉ

AU BRUIT

Ce qui peut se produire Comment l’Éviter

Dans certaines conditions et selon

la durée d’utilisation, le bruit

provoqué par ce produit peut

contribuer à une perte auditive.

Toujours utiliser un équipement de

sécurité homologué : protection

auditive conforme à la norme ANSI

S12.6 (S3.19).



DANGER: RISK TO BREATHING

(Asphyxiation)

Ce qui peut se produire Comment l’Éviter

Il est dangereux de respirer l’air

comprimé sortant du compresseur.

Le flux d’air peut contenir du

monoxyde de carbone, des vapeurs

toxiques ou des particules solides

provenant du réservoir d’air.

L’inhalation de ces contaminants

peut provoquer de sérieuses

blessures, voire un décès.

L’air qui s’obtient directement du

compresseur ne devrait jamais être

utilisé pour alimenter l’air destiné

à la consommation humaine.

Pour utiliser l’air produit par le

compresseur pour la respiration,

installer correctement des filtres

convenables et un équipement

de sécurité en ligne. Les filtres en

ligne et l’équipement de sécurité

utilisés avec le compresseur

doivent être capables de traiter l’air

conformément à tous les codes

locaux et fédéraux en vigueur avant

toute consommation humaine.

Les matériaux vaporisés comme la

peinture, les solvants de peinture,

les décapants, les insecticides, les

herbicides, pourraient contenir des

vapeurs nocives et du poison.

Travailler dans un endroit

ayant une bonne ventilation

transversale. Lire et respecter

les directives en matière de

sécurité imprimées sur l’étiquette

ou les fiches signalétiques des

matériaux qui sont pulvérisés.

Toujours utiliser un équipement

de sécurité homologué : une

protection respiratoire conforme

aux normes OSHA/MSHA/NIOSH,

conçue spécifiquement pour une

utilisation particulière.



AVERTISSEMENT : RISQUE D’ÉCLATEMENT

Réservoir d’air : Le réservoir dont est doté le compresseur d’air

(dans le cas d’appareils munis de réservoirs supérieurs à 152 mm

(6 po) de diamètre) et il est conçu conformément à la section VII Div.

1 de l’ASME. Tous les récipients sous pression devraient être inspectés

une fois tous les deux ans. Pour localiser l’inspecteur des récipients

sous pression de votre région, consulter la section appropriée des

organismes gouvernementaux de l’annuaire téléphonique ou composer

le 1–800–4-DeWALT pour obtenir de l’aide.

Les conditions indiquées ci-après pourraient affaiblir le réservoir d’air et

se solder par une violente explosion de celui-ci :

Ce qui peut se produire Comment l’Éviter

L’eau condensée n’est pas

correctement vidangée du réservoir

d’air provoquant ainsi la formation

de rouille et un amincissement du

réservoir d’air en acier.

Vidanger le réservoir d’air

quotidiennement ou après

chaque utilisation. Si le réservoir

présente une fuite, le remplacer

immédiatement par un nouveau

réservoir d’air ou par un

nouveau compresseur.

FRANÇAIS

Modifications apportées au

réservoir d’air ou tentatives

de réparation.

Ne jamais percer un trou dans le

réservoir d’air ou ses accessoires, y

faire de la soudure ou y apporter

quelque modification que ce soit.

Ne jamais essayer de réparer un

réservoir d’air endommagé ou avec

des fuites. Le remplacer par un

nouveau réservoir d’air.

Des modifications non autorisées

de la soupape de sûreté ou de tous

autres composants qui régissent la

pression du réservoir d’air.

Le réservoir d’air a été conçu pour

supporter des pressions spécifiques

de fonctionnement. Ne faites

jamais effectuer de réglages ou

de substitutions de pièces en

vue de modifier les pressions de

fonctionnement réglées en usine.

Accessoires :

Lorsqu’on excède la pression

nominale des outils pneumatiques,

des pistolets pulvérisateurs,

des accessoires à commande

pneumatique, des pneus et

d’autres dispositifs pneumatiques,

on risque de les faire exploser ou

de les projeter et ainsi entraîner des

blessures graves.

Respecter les recommandations

du fabricant de l’équipement et

ne jamais dépasser la pression

nominale maximale permise des

accessoires. Ne jamais utiliser le

compresseur pour gonfler de petits

objets à basse pression comme

des jouets d’enfant, des ballons de

football et de basket-ball, etc.

Pneus :

Des pneus surgonflés pourraient

provoquer des blessures graves et

des dommages à la propriété.

Utiliser un manomètre pour vérifier

la pression des pneus avant chaque

utilisation et lors du gonflage;

consulter le flanc de pneu pour

obtenir la pression correcte.

REMARQUE : Des réservoirs

d’air, des compresseurs et d’autres

appareils similaires

utilisés pour gonfler les pneus

peuvent remplir de petits pneus

à ces pressions très rapidement.

Régler le régulateur de pression

d’air à une pression moindre que

celle indiquée sur le pneu. Ajouter

de l’air par petite quantité et

utiliser fréquemment le manomètre

pour empêcher un surgonflage.



AVERTISSEMENT : RISQUE DE CHOC

ÉLECTRIQUE

Ce qui peut se produire Comment l’Éviter

Votre compresseur d’air est

alimenté par un bloc-piles. Comme

tout autre dispositif à courant

continu, il peut causer un choc

électrique s’il n’est pas utilisé

correctement.

Ne faites jamais fonctionner

le compresseur à l’extérieur

lorsqu’il pleut ou dans des

conditions humides.

Ne faites jamais fonctionner

le compresseur avec les

couvercles de protection enlevés

ou endommagés.

Les tentatives de réparation par

un personnel non qualifié peuvent

résulter en de graves blessures,

voire la mort par électrocution.

Tout câblage électrique ou toute

réparation nécessaire pour ce

produit doit être pris en charge par

un centre de réparation en usine

autorisé

DeWALT

ou un centre de

réparation

DeWALT

conformément

aux codes électriques nationaux

et locaux.



AVERTISSEMENT : RISQUE PROVENANT DES

OBJETS PROJETÉS EN L’AIR

Ce qui peut se produire Comment l’Éviter

Le flux d’air comprimé peut

endommager les tissus mous de

la peau exposée et peut projeter

la poussière, des fragments, des

particules détachées et des petits

objets à haute vitesse, ce qui

entraînerait des dommages et des

blessures personnelles.

Toujours utiliser de l’équipement

de sécurité homologué : protection

oculaire conforme à la norme ANSI

Z87.1 (CAN/CSA Z94.3) munie

d’écrans latéraux lors de l’utilisation

du compresseur.

Ne jamais pointer une buse ou un

pulvérisateur vers une partie du

corps ou vers d’autres personnes ou

des animaux.

Toujours mettre le compresseur

hors tension et purger la pression

du tuyau à air et du réservoir d’air

avant d’effectuer l’entretien, de

fixer des outils ou des accessoires.



AVERTISSEMENT : ATTENTION SURFACES

CHAUDES

Ce qui peut se produire Comment l’Éviter

Toucher à du métal exposé

comme la tête du compresseur

ou du moteur, la tubulure des gaz

d’échappement ou de sortie, peut

se solder en de sérieuses brûlures.

Ne jamais toucher à des

pièces métalliques exposées

sur le compresseur pendant

ou immédiatement après son

utilisation. Le compresseur reste

chaud pendant plusieurs minutes

après son utilisation.

Ne pas toucher ni effectuer

des réparations aux coiffes de

protection avant que l’appareil

n’ait refroidi



AVERTISSEMENT : RISQUE ASSOCIÉ

AUX PIÈCES MOBILES

Ce qui peut se produire Comment l’Éviter

Les pièces mobiles comme

les ventilateurs et bielles de

raccordement peuvent entraîner

des blessures graves s’ils viennent

en contact avec une partie de votre

corps ou avec vos vêtements.

Ne jamais utiliser le compresseur

si les protecteurs ou les couvercles

sont endommagés ou retirés.

Tenir les cheveux, les vêtements et

les gants hors de portée des pièces

en mouvement. Les vêtements

amples, bijoux ou cheveux longs

peuvent s’enchevêtrer dans les

pièces mobiles.

S’éloigner des évents car ces

derniers pourraient camoufler des

pièces mobiles.

FRANÇAIS

Utiliser le compresseur avec

des pièces endommagées ou

manquantes ou le réparer sans

coiffes de protection risque

de vous exposer à des pièces

mobiles et peut se solder par de

graves blessures.

Toutes les réparations requises pour

ce produit devraient être effectuées

par un centre de réparation de

l’usine D

WALT ou un centre de

réparation autorisé D

WALT.



AVERTISSEMENT : RISQUE ASSOCIÉ À

UTILISATION DANGEREUSE

Ce qui peut se produire Comment l’Éviter

Une utilisation dangereuse de

votre compresseur d’air pourrait

provoquer de graves blessures,

voire votre décès ou celle

d’autres personnes.

Revoir et comprendre toutes les

directives et les avertissements

contenus dans le présent mode

d’emploi.

Se familiariser avec le

fonctionnement et les commandes

du compresseur d’air.

Dégager la zone de travail de toutes

personnes, animaux et obstacles.

Tenir les enfants hors de portée du

compresseur d’air en tout temps.

Ne pas utiliser le produit en cas de

fatigue ou sous l’emprise d’alcool

ou de drogues. Rester vigilant en

tout temps.

Ne jamais modifier ou désaffecter

les dispositifs de sécurité de ce

produit.

Installer un extincteur dans la zone

de travail.

Ne pas utiliser l’appareil lorsqu’il

manque des pièces ou que

des pièces sont brisées ou

non autorisées.

Ne jamais se tenir debout sur

le compresseur.



AVERTISSEMENT : RISQUE DE CHUTE

Ce qui peut se produire Comment l’Éviter

Un compresseur portatif peut tomber

d’une table, d’un établi ou d’un toit et

causer des dommages au compresseur,

ce qui pourrait résulter en de graves

blessures, voire la mort de l’opérateur.

Toujours faire fonctionner le

compresseur alors qu’il est dans

uns position sécuritaire et stable

afin d’empêcher un mouvement

accidentel de l’appareil. Ne jamais

faire fonctionner le compresseur

sur un toit ou sur toute autre

position élevée. Utiliser un tuyau

d’air supplémentaire pour atteindre

les emplacements en hauteur.

CONSERVER CES CONSIGNES POUR

UTILISATION ULTÉRIEURE



AVERTISSEMENT : ce produit poourrait vous eposer

a des produits chimiques comprenant le plomb,

connu par l’État de la Calirornie causer le cancer et

des déficiences congénitales ou autre dangers de

reproduction. Pour plud de détails visitez le site

www.P65Warnings.ca.gov.



AVERTISSEMENT: les scies, meules, ponceuses,

perceuses ou autres outils de construction peuvent

produire des poussières contenant des produits

chimiques reconnus par l’État californien pour causer

cancers, malformations congénitales ou être nocifs au

système reproducteur. Parmi ces produits chimiques,

on retrouve:

• Le plomb dans les peintures à base de plomb;

• La silice cristallisée dans les briques et le ciment,

ou autres produits de maçonnerie; et

• L’arsenic et le chrome dans le bois ayant subi un

traitementchimique.

Le risque associé à de telles expositions varie selon la

fréquence à laquelle on effectue ces travaux. Pour réduire

toute exposition à ces produits: travailler dans un endroit

bien aéré, en utilisant du matériel de sécurité homologué, tel

un masque antipoussières spécialement conçu pour filtrer les

particulesmicroscopiques.

• Limiter toute exposition prolongée avec les

poussières provenant du ponçage, sciage, meulage,

perçage ou toute autre activité de construction.

Porter des vêtements de protection et nettoyer à

l’eau savonneuse les parties du corps exposées. Le

fait de laisser la poussière pénétrer dans la bouche, les

yeux ou la peau peut favoriser l’absorption de produits

chimiquesdangereux.

AVERTISSEMENT: cet outil peut produire et/ou répandre

de la poussière susceptible de causer des dommages

sérieux et permanents au système respiratoire. Utiliser

systématiquement un appareil de protection des voies

respiratoires homologué par le NIOSH ou l’OSHA. Diriger les

particules dans le sens opposé au visage et aucorps.

L’étiquette apposée sur votre outil peut inclure les symboles

suivants. Les symboles et leur définition sont indiqués ci-après:

V ......................... volts

Hz ....................... hertz

min ..................... minutes

or DC ...... courant continu

...................... fabrication classe I

(mis à la terre)

…/min .............. par minute

BPM .................... battements par

minute

IPM ..................... impacts par minute

RPM .................... revolutions per

minute

sfpm ................... pieds linéaires par

minute (plpm)

SPM (FPM) ......... fréquence par

minute

A ......................... ampères

W ........................ watts

or AC ........... courant alternatif

or AC/DC .... courant alternatif

ou continu

...................... fabrication classe II

(double isolation)

....................... vitesse à vide

n ......................... vitesse nominale

...................... borne de terre

...................... symbole

d’avertissement

..................... radiation visible

..................... protection

respiratoire

.....................protection oculaire

.....................protection auditive

..................... lire toute la

documentation

BLOCS-PILES ET CHARGEURS

Le bloc-piles n’est pas totalement chargé d’usine. Avant

d’utiliser le bloc-piles et le chargeur, lire les consignes de

sécurité ci-après puis suivre la procédure de chargement

FRANÇAIS

indiquée. Pour commander un bloc-piles de rechange,

s’assurer d’en inclure le numéro de catalogue et latension.

Cet outil fonctionne avec un chargeur

DeWALT

. S’assurer

de bien lire toutes les consignes de sécurité avant toute

utilisation du chargeur. Consulter le tableau en fin de

manuel pour connaître les compatibilités entre chargeurs

et blocs-piles.

LIRE TOUTES LES CONSIGNES

Consignes importantes de sécurité

les blocs-piles



AVERTISSEMENT : lire toutes les instructions et

toutes les consignes de sécurité propres au bloc-

piles, au chargeur et à l’outil électrique. Tout

manquement aux avertissements et instructions

pose des risques de décharges électriques,

d’incendie et/ou de blessures graves.

• Ne pas recharger ou utiliser un bloc-piles en milieu

déflagrant, en présence, par exemple, de poussières,

gaz ou liquides inflammables. Le fait d’insérer ou

retirer un bloc-piles de son chargeur pourrait causer

l’inflammation de poussières ou d’émanations.

• NE JAMAIS forcer l’insertion d’un bloc-piles dans un

chargeur. NE modifier un bloc-piles d’AUCUNE façon

pour le faire rentrer dans un chargeur incompatible,

car il pourrait se briser et causer des dommages

corporels graves. Consulter le tableau en dernière page

de ce manuel pour connaître les compatibilités entre

chargeurs et blocs-piles.

• Recharger les blocs-piles exclusivement dans des

chargeurs

DeWALT

• NE PAS éclabousser le bloc-piles ou l’immerger dans l’eau

ou dans tout autreliquide.

• Ne pas entreposer ou utiliser l’appareil et le bloc-

piles en présence de températures ambiantes

pouvant excéder 40°C (104°F) (comme dans des

hangars ou des bâtiments métalliques l’été). Pour

préserver leur durée de vie, entreposer les blocs-piles dans

un endroit frais etsec.

REMARQUE: ne pas mettre un bloc-piles dans un

outil dont la gâchette est verrouillée en position de

marche. Ne jamais bloquer l’interrupteur en position

deMARCHE.

• Ne pas incinérer le bloc-piles même s’il est

sévèrement endommagé ou complètement usagé,

car il pourrait exploser et causer un incendie.

Pendant l’incinération des blocs-piles au lithium-ion, des

vapeurs et matières toxiques sontdégagées.

• En cas de contact du liquide de la pile avec la peau,

rincer immédiatement au savon doux et à l’eau. En

cas de contact oculaire, rincer l’œil ouvert à l’eau claire

une quinzaine de minutes ou jusqu’à ce que l’irritation

cesse. Si des soins médicaux s’avéraient nécessaires, noter

que l’électrolyte de la pile est composé d’un mélange de

carbonates organiques liquides et de sels delithium.

• Le contenu des cellules d’une pile ouverte peut

causer une irritation respiratoire. En cas d’inhalation,

exposer l’individu à l’air libre. Si les symptômes persistent,

consulter unmédecin.



AVERTISSEMENT: risques de brûlure. Le liquide de la

pile peut s’enflammer s’il est exposé à des étincelles ou

à uneflamme.



AVERTISSEMENT: risques d’incendie. Ne jamais

tenter d’ouvrir le bloc-piles pour quelque raison

que ce soit. Si le boîtier du bloc-piles est fissuré ou

endommagé, ne pas l’insérer dans un chargeur. Ne

pas écraser, laisser tomber, ou endommager les blocs-

piles. Ne pas utiliser un bloc-piles ou un chargeur

qui a reçu un choc violent, ou si l’appareil est tombé,

a été écrasé ou endommagé de quelque façon que

ce soit (p. ex. percé par un clou, frappé d’un coup

de marteau, piétiné). Les blocs-piles endommagés

doivent être renvoyés à un centre de réparation pour

y êtrerecyclés.

Transport



AVERTISSEMENT: risques d’incendie. Au moment

de ranger ou transporter le bloc-piles, veiller à

protéger ses bornes à découvert de tout objet

métallique. Par exemple, éviter de placer le bloc-

piles dans un tablier, une poche, une boîte à outils

ou un tiroir, etc. contenant des objets tels que clous,

vis, clés, etc. Le fait de transporter des blocs-piles

comporte des risques d’incendie, car les bornes

des piles pourraient entrer, par inadvertance,

en contact avec des objets conducteurs, tels

que: clés, pièces de monnaie, outils ou autres.

La réglementation sur les produits dangereux

(Hazardous Material Regulations) du département

américain des transports interdit, en fait, le transport

des blocs-piles dans les commerces ou dans les avions

dans les bagages de cabine, À MOINS qu’ils ne soient

correctement protégés de tout court-circuit. Aussi

lors du transport individuel de blocs-piles, s’assurer

que leurs bornes sont bien protégées et isolées de

tout matériau pouvant entrer en contact avec elles et

provoquer un court-circuit.

Expédition du bloc-piles

DeWALT

FLEXVOLT

Le bloc-piles D

WALT FLEXVOLT

possède deux modes:

Utilisation et Expédition.

Mode Utilisation: lorsque le bloc-piles FLEXVOLT

est par

lui-même ou dans un produit D

WALT 20v max*, il

fonctionnera comme un bloc-piles de 20v max*. Lorsque le

bloc-piles FLEXVOLT

est dans un produit de 60v max* ou

120v max* (deux blocs-piles de 60v max*), il fonctionnera

comme un bloc-piles de 60v max*.

Mode Expédition: lorsque

le capuchon est inséré sur

le bloc-piles FLEXVOLT

le bloc-piles est en mode

Expédition. Les modules

de cellules sont électriquement déconnectés du bloc le

faisant correspondre à trois blocs-piles d’un wattheure (Wh)

inférieur comparé à un bloc-piles de wattheure élevé. Ce

passage à trois blocs-piles à un wattheure inférieur peut

permettre au bloc-piles d’être exempté de suivre certaines

La page charge ...

DeWalt DCC2560T1DCB606 Manuel utilisateur

Marque: DeWalt

Modèle: DCC2560T1DCB606

Catégorie: Compresseurs d'air

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DCC2560T1DCB606 User manual
español: DeWalt DCC2560T1DCB606 Manual de usuario

DeWalt DCC2560T1DCB606 Manuel utilisateur

DeWalt DCC2560T1DCB606 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents