Intec VORTEC Beast Manuel utilisateur

Marque: Intec

Modèle: VORTEC Beast

Taper: Manuel utilisateur

INTRODUCTION

CONTENTS

SAFETYMESSAGES

ENGLISHFRANÇAISESPAÑOL

ENGLISH

OWNER’S MANUAL

MANUEL DE L’UTILISATEUR

MANUALDELPROPIETARIO

DAMAGE PREVENTION MESSAGES

GX630 · GX660 · GX690

Thank you for purchasing a Honda engine. We want to help you to

get the best results from your new engine and to operate it safely.

This manual contains information on how to do that; please read it

carefully before operating the engine. If a problem should arise, or

if you have any questions about your engine, consult an

authorized Honda servicing dealer.

All information in this publication is based on the latest product

information available at the time of printing. Honda Motor Co., Ltd.

reserves the right to make changes at any time without notice and

without incurring any obligation. No part of this publication may

be reproduced without written permission.

This manual should be considered a permanent part of the engine

and should remain with the engine if resold.

The engine exhaust from this product

contains chemicals known to the State of

California to cause cancer, birth defects

or other reproductive harm.

We suggest you read the warranty policy to fully understand its

coverage and your responsibilities of ownership. The warranty

policy is a separate document that should have been given to you

by your dealer.

Your safety and the safety of others are very important. We have

provided important safety messages in this manual and on the

engine. Please read these messages carefully.

A safety message alerts you to potential hazards that could hurt

you or others. Each safety message is preceded by a safety alert

symbol and one of three words, DANGER, WARNING, or

CAUTION.

You WILL be KILLED or SERIOUSLY

HURT if you don’t follow instructions.

You CAN be KILLED or SERIOUSLY

HURT if you don’t follow instructions.

You CAN be HURT if you don’t follow

instructions.

These signal words mean:

Your engine or other property can be damaged if you

don’t follow instructions.

This word means:

The purpose of these messages is to help prevent damage to your

engine, other property, or the environment.

You will also see other important messages that are preceded by

the word NOTICE.

Each message tells you what the hazard is, what can happen, and

what you can do to avoid or reduce injury.

United States, Puerto Rico, and U.S. Virgin Islands:

Review the instructions provided with the equipment powered by

this engine for any additional information regarding engine

startup, shutdown,operation, adjustments or any special

maintenance instructions.

.......................INTRODUCTION .1

................SAFETY MESSAGES .1

..........SAFETY INFORMATION .2

.....SAFETY LABEL LOCATION .2

COMPONENT & CONTROL

................................LOCATION .3

................................FEATURES .3

BEFORE OPERATION

.................................... 4.SKCEHC

..............................OPERATION .4

SAFE OPERATING

.....................PRECAUTIONS .4

......STARTING THE ENGINE .4

......STOPPING THE ENGINE .5

.....SETTING ENGINE SPEED .6

.....SERVICING YOUR ENGINE .6

THE IMPORTANCE OF

....................MAINTENANCE .6

......MAINTENANCE SAFETY .6

.......SAFETY PRECAUTIONS .7

MAINTENANCE

............................SCHEDULE .7

...........................REFUELING .7

...........................ENGINE OIL .8

............Recommended Oil .8

..................Oil Level Check .8

.........................Oil Change .8

.............................OIL FILTER .9

........................AIR CLEANER .9

..........................Inspection .9

............................Cleaning .9

......................SPARK PLUG .10

.............SPARK ARRESTER .11

HELPFUL TIPS &

......................SUGGESTIONS .11

...STORING YOUR ENGINE .11

................TRANSPORTING .12

TAKING CARE OF

....UNEXPECTED PROBLEMS .13

........FUSE REPLACEMENT .13

..TECHNICAL INFORMATION .14

.....Serial Number Location .14

Battery Connections for

....................Electric Starter .14

.....Remote Control Linkage .15

CarburetorModifications for

.....High Altitude Operation .15

Emission Control System

.........................Information .16

..............................Air Index .17

.....................Specifications .17

........Tuneup Specifications .17

Quick Reference

.........................Information .17

................Wiring Diagrams .18

.CONSUMER INFORMATION .19

WARRANTY AND

DISTRIBUTOR/DEALER

.LOCATOR INFORMATION .19

CUSTOMER SERVICE

...................INFORMATION .19

37Z6L601

00X37-Z6L-6010

GX630R · GX660R · GX690R

09/07/07 20:32:15 32Z6L600_001

SAFETY INFORMATION SAFETY LABEL LOCATION

ENGLISH

WARNING LABEL For EU Except EU

MUFFLER CAUTION LABEL

WARNING LABEL

Understand the operation of all controls and learn how to stop

the engine quickly in case of emergency. Make sure the operator

receives adequate instruction before operating the equipment.

Your engine’s exhaust contains poisonous carbon monoxide.

Do not run the engine without adequate ventilation, and never

run the engine indoors.

The engine and exhaust become very hot during operation.

Keep the engine at least 1 meter (3 feet) away from buildings

and other equipment during operation. Keep flammable

materials away, and do not place anything on the engine while it

is running.

Do not allow children to operate the engine. Keep children and

pets away from the area of operation.

If the label comes off or becomes hard to read, contact your Honda

servicing dealer for replacement.

This label warns you of potential hazards that can cause serious

injury. Read it carefully.

attached to

product

supplied

with product

supplied

with product

supplied

with product

attached to

product

supplied

with product

Hot muffler can burn you.

Stay away if engine has been running.

Read Owner’s Manual before operation.

The engine emits toxic poisonous carbon

monoxide gas. Do not run in an enclosed area.

Gasoline is highly flammable and explosive.

Stop the engine and let cool before refueling.

Honda factory equipped muffler.

not included

supplied with product

09/07/07 20:32:37 32Z6L600_002

ENGLISH

Hour Meter

Oil Alert System (applicable types)

Fuel-cut Solenoid

FEATURES

COMPONENT & CONTROL LOCATION

OIL DRAIN BOLT

HIGH-MOUNT MUFFLER (B type)

SIDE-MOUNT MUFFLER

AIR CLEANER

SPARK PLUG

SCREEN GRID

PTO TYPE

THROTTLE

LEVER

HOUR METER

FUEL FILTER

PROTECTOR

FAN COVER

PTO TYPE

CHOKE

KNOB

ENGINE

SWITCH

OIL ALERT

INDICATOR

OIL FILLER CAP

SPARK PLUG

HIGH-MOUNT MUFFLER

(A type)

ELECTRIC STARTER

HOUR METER

OIL FILTER

OIL LEVEL DIPSTICK

OIL FILTER

OIL DRAIN BOLT

PROTECTOR FAN

COVER TYPE

OIL ALERT

INDICATOR

(RED)

After starting the engine, the

elapsed time of the engine in

use will be count.

If the engine stops and will not restart, check the engine oil level

(see page ) before troubleshooting in other areas.

The Oil Alert system is designed to prevent engine damage

caused by an insufficient amount of oil in the crankcase. Before

the oil level in the crankcase can fall below a safe limit, the Oil

Alert indicator (red) comes on and the Oil Alert system will

automatically stop the engine (the engine switch will remain in the

ON position).

The engine is equipped with a fuel-cut solenoid that allows fuel to

flow to the carburetor main jet when the engine switch is in the ON

or START position and stops the flow of fuel to the main jet when

the engine switch is in the OFF position.

The engine must be connected to the battery to energize the fuel-

cut solenoid, allowing the engine to run. If the battery is

disconnected, fuel flow to the carburetor will stop.

It will not count the elapsed

time of the engine operation by

just turning the engine switch

ON.

‘‘Oil Alert is a registered trademark in the United States’’

09/07/07 20:32:57 32Z6L600_003

ENGLISH

SAFE OPERATING PRECAUTIONS

STARTING THE ENGINE

IS YOUR ENGINE READY TO GO?

Check the General Condition of the Engine

Check the Engine

OPERATIONBEFORE OPERATION CHECKS

OOPPEENN

CCLLOOSSEEDD

CHOKE KNOB

Before operating the engine for the first time, please review the

SAFETY INFORMATION

section on page and the

BEFORE

OPERATION CHECKS

on page .

For your safety, do not operate the engine in an enclosed area

such as a garage. Your engine’s exhaust contains poisonous

carbon monoxide gas that can collect rapidly in an enclosed area

and cause illness or death.

Review the instructions provided with the equipment powered by

this engine for any safety precautions that should be observed

with engine startup, shutdown or operation.

Do not operate the engine on slopes greater than 20°.

To start a cold engine, pull the choke knob out to the CLOSED

position.

To restart a warm engine, leave the choke knob in the OPEN

position.

Some engine applications use a remote-mounted choke control

rather than the engine-mounted choke knob shown here. Refer

to the instructions provided by the equipment manufacturer.

Exhaust contains poisonous carbon monoxide gas

that can build up to dangerous levels in closed areas.

Breathing carbon monoxide can cause

unconsciousness or death.

Never run the engine in a closed, or even partly

closed area where people may be present.

Improperly maintaining this engine, or failure to

correct a problem before operation, can cause a

malfunction in which you can be seriously hurt or

killed.

Always perform a pre-operation inspection before

each operation, and correct any problem.

For your safety, and to maximize the service life of your

equipment, it is very important to take a few moments before you

operate the engine to check its condition. Be sure to take care of

any problem you find, or have your servicing dealer correct it,

before you operate the engine.

Before beginning your pre-operation checks, be sure the engine is

level and the engine switch is in the OFF position.

Always check the following items before you start the engine:

If the fuel tank is equipped with a valve, be sure the fuel valve is

in the OPEN or ON position before attempting to start the engine.

Look around and underneath the engine for signs of oil or

gasoline leaks.

Look for signs of damage.

Check that all shields and covers are in place, and all nuts, bolts,

and screws are tightened.

Check the engine oil level (see page ). Running the engine

with a low oil level can cause engine damage.

Check the fuel level. Starting with a full tank will help to

eliminate or reduce operating interruptions for refueling.

The Oil Alert system (applicable types) will automatically stop

the engine before the oil level falls below safe limits. However,

to avoid the inconvenience of an unexpected shutdown, always

check the engine oil level before startup.

Check the air filter element (see page ). A dirty air filter

element will restrict air flow to the carburetor, reducing engine

performance.

Check the equipment powered by this engine.

Review the instructions provided with the equipment powered

by this engine for any precautions and procedures that should

be followed before engine startup.

Remove any excessive dirt or debris, especially around the

muffler. 1.

09/07/07 20:33:20 32Z6L600_004

ENGLISH

STOPPING THE ENGINE

MMIINN..

START

ENGINE

SWITCH

START

ENGINE

SWITCH

THROTTLE LEVER

OONN

CHOKE KNOB

OOPPEENN

CCLLOOSSEEDD

OONN

MMIINN..

THROTTLE LEVER

ENGINE SWITCH

OFF

Some engine applications use a remote-mounted throttle control

rather than the engine-mounted throttle lever shown here. Refer to

the instructions provided by the equipment manufacturer.

Turn the engine switch to

the ON position.

Operate the starter.

Turn the engine switch to the START

position, and hold it there until the

engine starts.

If the engine fails to start within 5

seconds, release the engine switch,

and wait at least 10 seconds before

operating the starter again.

Using the electric starter for more than

5 seconds at a time will overheat the

starter motor and can damage it.

When the engine starts, release the

engine switch, allowing it to return

to the ON position.

Move the throttle lever away from the MIN. position, about 1/3

of the way toward the MAX. position.

Warm up the engine for 2 or 3 minutes.

If the choke knob was pulled to the CLOSED position to start the

engine, gradually push it to the OPEN position as the engine

warms up.

To stop the engine in an emergency, simply turn the engine switch

to the OFF position. Under normal conditions, use the following

procedure. Refer to the instructions provided by the equipment

manufacturer.

Move the throttle lever to the MIN. position.

Some engine applications use a remote-mounted throttle

control rather than the engine-mounted throttle lever shown

here.

Turn the engine switch to the OFF position.

If the fuel tank is equipped with a valve, turn the fuel valve to the

CLOSED or OFF position.

09/07/07 20:33:44 32Z6L600_005

ENGLISH

SERVICING YOUR ENGINE

THE IMPORTANCE OF MAINTENANCE

Maintenance, replacement, or repair of the emission control

devices and systems may be performed by any engine repair

establishment or individual, using parts that are ‘‘certified’’ to

EPA standards.

MAINTENANCE SAFETY

SETTING ENGINE SPEED

MMIINN..

MMAAXX..

THROTTLE LEVER

Good maintenance is essential for safe, economical and trouble-

free operation. It will also help reduce pollution.

Improper maintenance, or failure to correct a

problem before operation, can cause a malfunction in

which you can be seriously hurt or killed.

Always follow the inspection and maintenance

recommendations and schedules in this owner’s

manual.

To help you properly care for your engine, the following pages

include a maintenance schedule, routine inspection procedures,

and simple maintenance procedures using basic hand tools. Other

service tasks that are more difficult, or require special tools, are

best handled by professionals and are normally performed by a

Honda technician or other qualified mechanic.

The maintenance schedule applies to normal operating conditions.

If you operate your engine under severe conditions, such as

sustained high-load or high-temperature operation, or use in

unusually wet or dusty conditions, consult your Honda servicing

dealer for recommendations applicable to your individual needs

and use.

Some of the most important safety precautions follow. However,

we cannot warn you of every conceivable hazard that can arise in

performing maintenance. Only you can decide whether or not you

should perform a given task.

Failure to properly follow maintenance instructions

and precautions can cause you to be seriously hurt or

killed.

Always follow the procedures and precautions in this

owner’s manual.

Position the throttle lever for the desired engine speed.

Some engine applications use a remote-mounted throttle control

rather than the engine-mounted throttle lever shown here. Refer to

the instructions provided by the equipment manufacturer.

For engine speed recommendations, refer to the instructions

provided with the equipment powered by this engine.

Do not disconnect the battery from the engine while the engine is

running. Disconnecting the battery causes the fuel-cut solenoid to

shut off the flow of fuel to the carburetor main jet, and the engine

will stop.

09/07/07 20:33:59 32Z6L600_006

ENGLISH

SAFETY PRECAUTIONS

Carbon monoxide poisoning from engine exhaust.

Burns from hot parts.

Injury from moving parts.

MAINTENANCE SCHEDULE

REFUELING

Recommended Fuel

Make sure the engine is off before you begin any maintenance

or repairs. To prevent accidental startup, disconnect the spark

plug cap. This will eliminate several potential hazards:

Operate outside, away from open windows or doors.

Let the engine and exhaust system cool before touching.

Do not run the engine unless instructed to do so.

Read the instructions before you begin, and make sure you have

the tools and skills required.

To reduce thepossibility of fire or explosion, be careful when

working around gasoline. Use only a non-flammable solvent,

not gasoline, to clean parts. Keep cigarettes, sparks and flames

away from all fuel related parts.

Remember that an authorized Honda servicing dealer knows your

engine best and is fully equipped to maintain and repair it.

To ensure the best quality and reliability, use only new Honda

Genuine parts or their equivalents for repair and replacement.

Service more frequently when used in dusty areas.

These items should be serviced by yourHonda servicing

dealer, unless you have the proper tools and are mechanically

proficient. Refer to the Honda shop manual for service

procedures.

For commercial use, log hours of operation to determine

proper maintenance intervals.

Failure to follow this maintenance schedule could result in non-

warrantable failures.

Unleaded gasoline

U.S.

Except U.S.

Pump octane rating 86 or higher

Research octane rating 91 or higher

Pump octane rating 86 or higher

This engine is certified to operate on unleaded gasoline with a

pump octane rating of 86 or higher (a research octane rating of 91

or higher).

Refuel in a well ventilated area with the engine stopped. If the

engine has been running, allow it to cool first. Never refuel the

engine insideabuilding where gasoline fumes may reach flames

or sparks.

You may use unleaded gasoline containing no more than 10%

ethanol (E10) or 5% methanol by volume. In addition, methanol

must contain cosolvents and corrosion inhibitors. Use of fuels

with content of ethanol or methanol greater than shown above

may cause starting and/or performance problems. It may also

damage metal, rubber, and plastic parts of the fuel system. Engine

damage or performance problems that result from using a fuel

with percentages of ethanol or methanol greater than shown

above are not covered under the Warranty.

If your equipment will be used on an infrequent or intermittent

basis, please refer to the fuel section of the STORING YOUR

ENGINE chapter (see page ) for additional information

regarding fuel deterioration.

Spilled fuel is not onlyafire hazard, it causes environmental

damage. Wipe up spills immediately.

Keep gasoline away from appliance pilot lights, barbecues,

electric appliances, power tools, etc.

Refuel in a well-ventilated area before starting the engine. If the

engine has been running, allow it to cool. Refuel carefully to avoid

spilling fuel. It may be necessary to lower the fuel level depending

on operating conditions. After refueling, tighten the fuel tank cap

securely.

Refer to the instructions provided with the equipment powered by

this engine for refuelling.

With the engine stopped and on a level surface, remove the fuel

filler cap and check the fuel level. Refill the tank if the fuel level is

low.

Never use stale or contaminated gasoline or an oil/gasoline

mixture. Avoid getting dirt or water in the fuel tank.

Fuel can damage paint and some types of plastic. Be careful not to

spill fuel when filling your fuel tank. Damage caused by spilled

fuel is not covered under the

Distributor’s Limited Warranty.

Gasoline is highly flammable and explosive, and you

can be burned or seriously injured when refueling.

Stop the engine and keep heat, sparks, and flame

away.

Refuel only outdoors.

Wipe up spills immediately.

Replace the paper filter element only.

Refer to the Shop Manual.

(1)

(2)

(3)

In Europe and other countries where the machinery directive

2006/42/EC is enforced, this cleaning should be done by your

servicing dealer.

(4)

REGULARSERVICEPERIOD (3)

Perform at every

indicated month or

operating hourinterval,

whichever comes first.

ITEM

Engineoil

Engineoil filter

Air cleaner

Spark plug

Spark arrester

( )

Idle speed

Valve clearance

Combustion

chamber

Fuel filter

Fuel tube

Check level

Change

Replace

Check

Clean

Replace

Check-adjust

Replace

Clean

Check-adjust

Clean

Replace

Check

First

Month

20 Hrs

Refer

Page

Every 6

Months

100 Hrs

(1)

(4)

Every

Year

300 Hrs

(2)

Every 2

Years

500 Hrs

Each

Use

Every 200 Hrs.

After every 1000 Hrs. (2)

Every2years (Replace if necessary) (2)

applicable types

09/07/07 20:34:32 32Z6L600_007

ENGLISH

ENGINE OIL

Recommended Oil

Oil Level Check

Oil Change

AMBIENT TEMPERATURE

OIL FILLER

CAP

UPPER LIMIT

LOWER LIMIT

OIL LEVEL DIPSTICK

UPPER

LIMIT

LOWER

LIMIT

SEALING WASHER

DRAIN BOLT

OIL FILLER CAP OIL LEVEL DIPSTICK

Synthetic 5W-30

Use 4-stroke motor oil that meets or exceeds the requirements for

API service category SJ or later (or equivalent). Always check the

API service label on the oil container to be sure it includes the

letters SJ or later (or equivalent).

Check the engine oil level with the engine stopped and in a level

position.

Start the engine and let it idle for 1 or 2 minutes. Stop the engine

and wait for 2 or 3 minutes.

Remove the oil level dipstick and wipe it clean.

Fully insert the oil level dipstick, then remove it to check the oil

level.

If the oil level is low, remove the oil filler cap, and fill with the

recommended oil to the upper limit mark on the oil level dipstick.

Reinstall the oil level dipstick and oil filler cap.

The Oil Alert system (applicable types) will automatically stop the

engine before the oil level falls below the safe limit. However, to

avoid the inconvenience of an unexpected shutdown, always

check the engine oil level before startup.

Oil is a major factor affecting performance and service life.

Use 4-stroke automotive detergent oil.

Drain the used oil when the engine is warm. Warm oil drains

quickly and completely.

Place a suitable container below the engine to catch the used oil,

then remove the oil filler cap, drain bolt and sealing washer.

Allow the used oil to drain completely, then reinstall the drain

bolt and new sealing washer, and tighten the drain bolt securely.

Please dispose of used motor oil in a manner that is compatible

with the environment. We suggest you take used oil in a sealed

container to your local recycling center or service station for

reclamation. Do not throw it in the trash, pour it on the ground,

or pour it down a drain.

Reinstall the oil filler cap and oil level dipstick securely.

The Oil Alert system (applicable types) will automatically stop

the engine before the oil level falls below the safe limit.

However, to avoid the inconvenience of an unexpected

shutdown, fill to the upper limit, and check the oil level regularly.

With the engine in a level position, fill with the recommended oil

to the upper limit mark on the oil level dipstick.

Running the engine with a low oil level can cause engine damage.

This type of damage is not covered by the

Distributor’s Limited

Warranty.

Running the engine with a low oil level can cause engine

damage. This type of damage is not covered by the

Distributor’s

Limited Warranty.

SAE 10W-30 or 5W-30 is recommended for general use. Use a full

synthetic 5W-30 for starting/operating temperatures between 5°F

( 15°C) and 13°F ( 25°C). Other viscosities shown in the chart

may be used when the average temperature in your area is within

the indicated range.

09/07/07 20:34:57 32Z6L600_008

ENGLISH

AIR CLEANER

Inspection

Cleaning

OIL FILTER

Change

OIL FILTER

SEAL

FILTER MOUNTING BASE OIL FILTER SOCKET

AIR CLEANER COVER LATCH

AIR CLEANER CASE

PACKING

FOAM FILTER

ELEMENT

PAPER FILTER

ELEMENT

AIR CLEANER

COVER

WING NUT

AIR CHAMBER

Operating the engine without an air filter, or with a damaged air

filter, will allow dirt to enter the engine, causing rapid engine wear.

This type of damage is not covered by the

Distributor’s Limited

Warranty.

Remove the air cleaner cover and inspect the filter elements.

Clean or replace dirty filter elements. Always replace damaged

filter elements.

Pull the air cleaner cover latch to the unlocked position, and

remove the cover.

Remove the paper filter element and foam filter element from

the air cleaner case.

Inspect both filter elements, and replace them if they are

damaged. Always replace the paper filter element at the

scheduled interval (see page ).

A dirty air cleaner will restrict air flow to the carburetor, reducing

engine performance. If you operate the engine in very dusty areas,

clean the air filter more often than specified in the MAINTENANCE

SCHEDULE (see page ).

Remove the wing nut from the paper filter element.

Drain the engine oil, and retighten the drain bolt securely.

Remove the oil filter, and drain the oil into a suitable container.

Dispose the used oil and filter in a manner compatible with the

environment.

Use an oil filter socket, rather than a strap wrench, to avoid

striking and damaging the oil pressure switch.

Clean the filter mounting base, and coat the seal of the new oil

filter with clean engine oil.

Use only a Honda Genuine oil filter or a filter of equivalent

quality specified for your model. Using the wrong filter, or a

non-Honda filter which is not of equivalent quality, may cause

engine damage.

Oil filter tightening torque:

Refill the crankcase with the specified amount of the

recommended oil (see page ). Reinstall the oil filler cap and oil

level dipstick.

Start the engine, and check for leaks.

Stop the engine, and check the oil level as described on page .

If necessary, add oil to bring the oil level to the upper limit mark

on the oil level dipstick.

Screw on the new oil filter by hand until the seal contacts the

filter mounting base, then use an oil filter socket tool to tighten

the filter an additional 3/4 turn.

12 N·m (1.2 kgf·m , 9 lbf·ft)

Remove the foam filter element from the paper filter element.

09/07/07 20:35:22 32Z6L600_009

ENGLISH

SPARK PLUG

Recommended Spark Plug:

SPARK PLUG CAP

0.7 0.8 mm

(0.028 0.031 in)

SEALING

WASHER

Dry

Soak Squeeze SqueezeOil

SPARK PLUG WRENCH

SIDE ELECTRODE

Clean the filter elements if they are to be reused.

Paper filter element: Tap the filter element several times on a

hard surface to remove dirt, or blow compressed air [not

exceeding 207 kPa (2.1 kgf/cm , 30 psi)] through the filter

element from the air cleaner case side.

Never try to brush off dirt; brushing will force dirt into the fibers.

Replace the paper filter element if it is excessively dirty.

Foam filter element: Clean in warm soapy water, rinse, and

allow to dry thoroughly. Or clean in non-flammable solvent and

allow to dry. Dip the filter element in clean engine oil, then

squeeze out all excess oil. The engine will smoke when started if

too much oil is left in the foam.

Wipe dirt from the inside of the air cleaner body and cover,

using a moist rag. Be careful to prevent dirt from entering the air

chamber that leads to the carburetor.

Place the foam filter element over the paper filter element, and

reinstall the assembled filter element. Be sure the packing is in

place beneath the filter element. Tighten the wing nut securely.

Lock the air cleaner cover latch securely.

Attach the spark plug caps to the spark plugs.

A loose spark plug can overheat and damage the engine.

Overtightening the spark plug can damage the threads in the

cylinder head.

When reinstalling the original spark plug, tighten 1/8 1/4 turn

after the spark plug seats to compress the washer.

When installing a new spark plug, tighten 1/2 turn after the spark

plug seats to compress the washer.

After the spark plug is seated, tighten with a 5/8-inch spark plug

wrench to compress the sealing washer.

Install the spark plug carefully,

by hand, to avoid cross-

threading.

0.7 0.8 mm (0.028 0.031 in)

The gap should be:

Measure the spark plug

electrode gaps with a wire-type

feeler gauge. Correct the gap, if

necessary, by carefully bending

thesideelectrode.

Inspect the spark plugs. Replace

them if damaged, badly fouled,

if the sealing washer is in poor

condition, or if the electrode is

worn.

Incorrect spark plugs can cause engine damage.

If the engine has been running, let it cool before servicing the

spark plugs.

For good performance, the spark plugs must be properly gapped

and free of deposits.

Disconnect the spark plug caps, and remove any dirt from

around the spark plug area.

Remove the spark plugs with a 5/8-inch spark plug wrench.

The recommended spark plug has the correct heat range for

normal engine operating temperatures.

ZFR5F (NGK)

09/07/07 20:35:46 32Z6L600_010

ENGLISH

HELPFUL TIPS & SUGGESTIONS

STORING YOUR ENGINE

Storage Preparation

Cleaning

Fuel

Spark Arrester Cleaning & Inspection

SPARK ARRESTER (applicable types)

Adding a Gasoline Stabilizer to Extend Fuel Storage Life

MUFFLER

SPARK ARRESTER

HIGH-MOUNTMUFFLER TYPE SIDE-MOUNTMUFFLER TYPE

SPARK ARRESTER SCREEN

SPECIAL

SCREW

SPARK ARRESTER

6mmFLANGEBOLTS (4)

SPECIALSCREWS (3)

MUFFLER PROTECTOR

MUFFLER

Proper storage preparation is essential for keeping your engine

trouble-free and looking good. The following steps will help to

keep rust and corrosion from impairing your engine’s function and

appearance, and will make the engine easier to start when you use

it again.

If the engine has been running, allow it to cool for at least half an

hour before cleaning. Clean all exterior surfaces, touch up any

damaged paint, and coat other areas that may rust with a light film

of oil.

Using a garden hose or pressure washing equipment can force

water into the air cleaner or muffler opening. Water in the air

cleaner will soak the air filter, and water that passes through the

air filter or muffler can enter the cylinder, causing damage.

HIGH-MOUNT MUFFLER TYPE: Remove the special screw from

the muffler and remove the spark arrester.

Remove the spark arrester:

If the engine has been running, the muffler will be hot. Allow it to

cool before servicing the spark arrester.

The spark arrester must be serviced every 100 hours to keep it

functioning as designed.

Your engine is not factory-equipped with a spark arrester. The

In Europe and other countries where the machinery directive

2006/42/EC is enforced, this cleaning should be done by your

servicing dealer.

spark arrester is optional part. In some areas, it is illegal to operate

an engine without a spark arrester. Check local laws and

regulations. A spark arrester is available from authorized Honda

servicing dealers.

Stop the engine, and if the fuel tank is equipped with a fuel valve,

move the fuel valve to the CLOSED or OFF position.

After adding a gasoline stabilizer, run the engine outdoors for 10

minutes to be sure that treated gasoline has replaced the

untreated gasoline in the carburetor.

Add gasoline stabilizer following the manufacturer’s instructions.

When adding a gasoline stabilizer, fill the fuel tank with fresh

gasoline. If only partially filled, air in the tank will promote fuel

deterioration during storage. If you keep a container of gasoline

for refueling, be sure that it contains only fresh gasoline.

You can extend fuel storage life by adding a gasoline stabilizer

that is formulated for that purpose, or you can avoid fuel

deterioration problems by draining the fuel tank and carburetor.

Fuel system damage or engine performance problems resulting

from neglected storage preparation are not covered under the

Distributor’s Limited Warranty

The length of time that gasoline can be left in your fuel tank and

carburetor without causing functional problems will vary with

such factors as gasoline blend, your storage temperatures, and

whether the fuel tank is partially or completely filled. The air in a

partially filled fuel tank promotes fuel deterioration. Very warm

storage temperatures accelerate fuel deterioration. Fuel

deterioration problems may occur within a few months, or even

less if the gasoline was not fresh when you filled the fuel tank.

Gasoline will oxidize and deteriorate in storage. Deteriorated

gasoline will cause hard starting, and it leaves gum deposits that

clog the fuel system. If the gasoline in your engine deteriorates

during storage, you may need to have the carburetor and other

fuel system components serviced or replaced.

Depending on the region where you operate your equipment, fuel

formulations may deteriorate and oxidize rapidly. Fuel

deterioration and oxidation can occur in as little as 30 days and

may cause damage to the carburetor and/or fuel system. Please

check with your servicing dealer for local storage

recommendations.

Install the spark arrester and muffler protector in the reverse

order of disassembly.

The spark arrester must be free of breaks and holes. Replace the

spark arrester if it is damaged.

Use a brush to remove carbon deposits from the spark arrester

screen. Be careful to avoid damaging the screen.

SIDE-MOUNT MUFFLER TYPE: Remove the6mm flange bolts

from themuffler protector and remove themuffler protector.

Remove the special screws from the spark arrester and remove

the spark arrester from the muffler.

09/07/07 20:36:16 32Z6L600_011

ENGLISH

Storage Precautions

Removal from Storage

TRANSPORTING

Draining the Fuel Tank and Carburetor

Engine Oil

DRAIN SCREW

CARBURETOR

If your engine will be stored with gasoline in the fuel tank and

carburetor, it is important to reduce the hazard of gasoline vapor

ignition. Select a well ventilated storage area away from any

appliance that operates with a flame, such as a furnace, water

heater, or clothes dryer. Also avoid any area with a spark-

producing electric motor, or where power tools are operated.

If possible, avoid storage areas with high humidity, because that

promotes rust and corrosion.

Keep the engine level in storage. Tilting can cause fuel or oil

leakage.

Unless all fuel has been drained from the fuel tank, leave the fuel

valve in the CLOSED or OFF position to reduce the possibility of

fuel leakage.

With the engine and exhaust system cool, cover the engine to

keep out dust. A hot engine and exhaust system can ignite or melt

some materials. Do not use sheet plastic as a dust cover.

A nonporous cover will trap moisture around the engine,

promoting rust and corrosion.

If installed, remove the battery and store it in a cool, dry place.

Recharge the battery once a month while the engine is in storage.

This will help to extend the service life of the battery.

Check your engine as described in the

BEFORE OPERATION

CHECKS

section of this manual (see page ).

If the fuel was drained during storage preparation, fill the tank with

fresh gasoline. If you keep a container of gasoline for refueling, be

sure it contains only fresh gasoline. Gasoline oxidizes and

deteriorates over time, causing hard starting.

Gasoline is highly flammable and explosive, and you

can be burned or seriously injured when handling

fuel.

If the engine has been running, allow it to cool for at least 15

minutes before loading the engine-powered equipment on the

transport vehicle. A hot engine and exhaust system can burn you

and can ignite some materials.

If the cylinders were coated with oil during storage preparation,

the engine may smoke briefly at startup. This is normal.

Stop the engine and keep heat, sparks, and flame

away.

Loosen the carburetor drain screw, and drain the carburetor into

an approved gasoline container. After draining is completed,

tighten the carburetor drain screw.

Disconnect the fuel line to the engine, and drain the fuel tank

into an approved gasoline container. If the fuel tank is equipped

with a valve, turn the fuel valve to the OPEN or ON position to

enable draining. After draining is completed, reconnect the fuel

line.

Wipe up spills immediately.

Keep the engine level when transporting to reduce the possibility

of fuel leakage. If the fuel tank is equipped with a fuel valve, move

the fuel valve lever to the CLOSED or OFF position.

Reinstall the spark plugs.

Turn the engine for a few seconds by turning the engine switch

to the START position to distribute the oil in the cylinders.

Remove the spark plugs (see page ).

Change the engine oil (see page ).

Handle fuel only outdoors.

Pour 5 10 cm (5 10 cc, 1 2 teaspoons) of clean engine oil

into each cylinder.

09/07/07 20:36:39 32Z6L600_012

ENGLISH

TAKING CARE OF UNEXPECTED PROBLEMS

ENGINE WILL

NOT START

Possible Cause Correction

FUSE REPLACEMENT

ENGINE LACKS

POWER

Possible Cause Correction FUSE COVER

WIRE HARNESSES

WIRE CONNECTOR

30 A FUSE

SWITCH BOX REAR COVER

6 8 mm SPECIAL SCREW

WIRE HARNESS

BAND

The electric starter relay circuit and battery charging circuit are

protected by a 30-ampere fuse. If the fuse burns out, the electric

starter will not operate.Electric

starting:

Check battery

and fuse.

Check control

positions.

Check engine

oil level.

Check fuel.

Remove and

inspect spark

plugs.

Take engine to

an authorized

Honda

servicing

dealer, or refer

to shop

manual.

Check air filter.

Check fuel.

Take engine to

an authorized

Honda

servicing

dealer, or refer

to shop

manual.

Clean or replace

filter element(s)

(p. 9).

Drain fuel tank and

carburetor (p. 12).

Refuel with fresh

gasoline (p. 7).

Replace or repair

faulty components

as necessary.

Battery

discharged.

Fuse burnt out.

Fuel valve

CLOSED or OFF.

(If equipped)

Choke OPEN.

Engine switch

OFF.

Engine oil level

low (Oil Alert

stops engine).

Out of fuel.

Stale fuel;

engine stored

without treating

or draining

gasoline, or

refueled with

stale gasoline.

Spark plugs

faulty, fouled, or

improperly

gapped.

Spark plugs wet

with fuel

(flooded engine).

Fuel filter

restricted,

carburetor

malfunction,

ignition

malfunction,

valves stuck, etc.

Filter element(s)

restricted.

Stale fuel;

engine stored

without treating

or draining

gasoline, or

refueled with

stale gasoline.

Fuel filter

restricted,

carburetor

malfunction,

ignition

malfunction,

valves stuck, etc.

Recharge battery.

Replace fuse.

Move lever to

OPEN or ON

position.

Move knob to

CLOSED position

unless the engine

is warm (p. 4).

Turn engine switch

to ON position

(p. 5).

Fill with the

recommended oil

to the proper level

(p. 8).

Refuel (p. 7).

Drain fuel tank and

carburetor (p. 12).

Refuel with fresh

gasoline (p. 7).

Gap, or replace

spark plugs (p. 10).

Dry and reinstall

spark plugs (p. 10).

Start engine with

throttle lever in

MAX. position

(p. 6).

Replace or repair

faulty components

as necessary.

Disconnect the wire connector, and remove the wire harnesses

from the wire harness band.

Remove the 6 8 mm special screw from the rear cover of the

engine switch box, and remove the rear cover.

Remove the fuse cover, and inspect the fuse.

If the fuse is burnt out, remove the fuse cover, then pull out and

discard the burnt-out fuse. Install a new 30-ampere fuse, and

reinstall the fuse cover.

Never use a fuse with a rating greater than 30 amperes. Serious

damage to the electrical system or a fire could result.

Reinstall the rear cover. Install the 6 8 mm special screw and

tighten it securely.

Frequent fuse failure usually indicates a short circuit or an

overload in the electrical system. If the fuse burns out frequently,

take the engine to a Honda servicing dealer for repair.

09/07/07 20:37:01 32Z6L600_013

ENGLISH

Battery Connections for Electric Starter

Serial Number Location

WARNING:

Wash hands after handling.

Recommended Battery

TECHNICAL INFORMATION

STARTER

SOLENOID

POSITIVE ( )

BATTERY CABLE

NEGATIVE ( )

BATTERY CABLE

SERIAL NUMBER &

ENGINE TYPE LOCATION

Record the engine serial number, type and purchase date in the

spaces below. You will need this information when ordering parts

and when making technical or warranty inquiries.

Engine serial number: __ __ __ __ __ __ __ __ __ __ __

Engine type: ___ ___ ___ ___

Date Purchased: ______ / ______ / ______

Coat the terminals and cable ends with grease.

Connect the battery negative ( ) cable to the battery negative

( ) terminal as shown.

Connect the battery positive ( ) cable to the battery positive ( )

terminal as shown.

Connect the battery negative ( ) cable to an engine mounting

bolt, frame bolt, or other good engine ground connection.

Connect the battery positive ( ) cable to the starter solenoid

terminal as shown.

Battery posts, terminals, and related accessories

contain lead and lead compounds.

Keep all sparks, open flames, and smoking materials

away from the battery.

A battery can explode if you do not follow the correct

procedure, seriously injuring anyone nearby.

Be careful not to connect the battery in reverse polarity, as this will

short circuit the battery charging system. Always connect the

positive ( ) battery cable to the battery terminal before

connecting the negative ( ) battery cable, so your tools cannot

cause a short circuit if they touch a grounded part while tightening

the positive ( ) battery cable end.

12 V 36 Ah

GX630

GX660

GX690

09/07/07 20:37:18 32Z6L600_014

ENGLISH

Remote Control Linkage

Carburetor Modifications for High Altitude Operation

516mm(2)

CHOKE CONTROL

LEVER

GOVERNOR SPRING

CABLE

HOLDER (2)

THROTTLE CONTROL LEVER

516mm(2)

CHOKE CONTROL

LEVER

GOVERNOR SPRING

46mm

CABLE HOLDER (2)

THROTTLE CONTROL

LEVER

CABLE

CHOKE CABLE

THROTTLE CABLE

CHOKE CABLE

THROTTLE CABLE

46mm

CABLE

WIRE HOLDER

RIGHT SIDE CONTROL

LEFT SIDE CONTROL

WIRE HOLDER

For Choke Cable

For Throttle Cable

5mm

CIRCLIP

46mm

THROTTLE CABLE

WIRE HOLDER

(for throttle cable)

5mm

CIRCLIP

THROTTLE CONTROL LEVER

CHOKE CONTROL LEVER

46mm

WIRE HOLDER

(for choke cable)

CHOKE CABLE

The throttle and choke control levers are provided with holes for

optional cable attachment. The following illustrations show

installation examples for a solid wire cable and for a flexible,

braided wire cable.

At high altitude, the standard carburetor air-fuel mixture will be

too rich. Performance will decrease, and fuel consumption will

increase. A very rich mixture will also foul the spark plug and

cause hard starting. Operation at an altitude that differs from that

at which this engine was certified, for extended periods of time,

may increase emissions.

High altitude performance can be improved by specific

modifications to the carburetor. If you always operate your engine

at altitudes above 1,500 meters (5,000 feet), have your servicing

dealer perform this carburetor modification. This engine, when

operated at high altitude with the carburetor modifications for

high altitude use, will meet each emission standard throughout its

useful life.

Even with carburetor modification, engine horsepower will

decrease about 3.5% for each 300 meter (1,000 foot) increase in

altitude. The effect of altitude on horsepower will be greater than

this if no carburetor modification is made.

When the carburetor has been modified for high altitude operation,

the air-fuel mixture will be too lean for low altitude use. Operation

at altitudes below 1,500 meters (5,000 feet) with a modified

carburetor may cause the engine to overheat and result in serious

engine damage. For use at low altitudes, have your servicing

dealer return the carburetor to original factory specifications.

09/07/07 20:37:37 32Z6L600_015

ENGLISH

Emission Control System Information

Source of Emissions

Replacement Parts

Maintenance

Problems That May Affect Emissions

Tampering and Altering

The U.S., California Clean Air Act, and Environment Canada

The combustion process produces carbon monoxide, oxides of

nitrogen, and hydrocarbons. Control of hydrocarbons and oxides

of nitrogen is very important because, under certain conditions,

they react to form photochemical smog when subjected to

sunlight. Carbon monoxide does not react in the same way, but it

is toxic.

The emission control systems on your Honda engine were

designed, built, and certified to conform with EPA, California

(models certified for sale in California), and Canadian emission

regulations. We recommend the use of Honda Genuine parts

whenever you have maintenance done. These original-design

replacement parts are manufactured to the same standards as the

original parts, so you can be confident of their performance. The

use of replacement parts that are not of the original design and

quality may impair the effectiveness of your emission control

system.

Follow the maintenance schedule on page . Remember that this

schedule is based on the assumption that your machine will be

used for its designed purpose. Sustained high-load or high-

temperature operation, or use in unusually wet or dusty conditions,

will require more frequent service.

A manufacturer of an aftermarket part assumes the responsibility

that the part will not adversely affect emission performance. The

manufacturer or rebuilder of the part must certify that use of the

part will not result in a failure of the engine to comply with

emission regulations.

Honda utilizes appropriate air/fuel ratios and other emissions

control systems to reduce the emissions of carbon monoxide,

oxides of nitrogen, and hydrocarbons.

Additionally, Honda fuel systems utilize components and control

technologies to reduce evaporative emissions.

Black exhaust smoke or high fuel consumption.

Afterburning (backfiring).

Misfiring or backfiring under load.

Rough idle.

Hard starting or stalling after starting.

If you are aware of any of the following symptoms, have your

engine inspected and repaired by your servicing dealer.

Altering or defeating the governor linkage or speed-adjusting

mechanism to cause the engine to operate outside its design

parameters.

Removal or alteration of any part of the intake, fuel, or exhaust

systems.

Tampering with or altering the emission control system may

increase emissions beyond the legal limit. Among those acts that

constitute tampering are:

The following instructions and procedures must be followed in

order to keep the emissions from your Honda engine within the

emission standards.

EPA, California, and Canadian regulations require all

manufacturers to furnish written instructions describing the

operation and maintenance of emission control systems. 7

09/07/07 20:37:54 32Z6L600_016

ENGLISH

Air Index

Descriptive Term Applicable to Emissions Durability Period

Specifications

MAINTENANCEITEM

Tuneup Specifications

Quick Reference Information

SPECIFICATION

GX630 (QAF-Type)

GX660 (TAF-Type)

GX690 (TAF-Type)

GX630/660/690

The bar graph is intended to provide you, our customer, the ability

to compare the emissions performance of available engines. The

lower the Air Index, the less pollution.

Extended

Intermediate

Moderate

125 hours (0 80 cc, inclusive)

250 hours (greater than 80 cc)

50 hours (0 80 cc, inclusive)

125 hours (greater than 80 cc)

300 hours (0 80 cc, inclusive)

500 hours (greater than 80 cc)

1,000 hours (225 cc and greater)

An Air Index Information label is applied to engines certified to an

emission durability time period in accordance with the

requirements of the California Air Resources Board.

405 410 438 mm

(15.9 16.1 17.2 in)

44.4 kg (97.9 lbs)

688.0 cm (41.97 cu-in)

[78.0 72.0 mm (3.07 2.83 in)]

15.5 kW (21.1 PS, 20.8 bhp) at 3,600 rpm

48.3 N·m (4.93 kgf·m, 35.6 lbf·ft)

at 2,500 rpm

Length Width

Height

Dry mass [weight]

Engine type

Displacement

[Bore Stroke]

Net power

Max. Net torque

Engine oil capacity

Cooling system

Ignition system

PTO shaft rotation

Forced air

CDI type magneto ignition

Counterclockwise

Length Width

Height

Dry mass [weight]

Engine type

Displacement

[Bore Stroke]

Net power

Max. Net torque

Engine oil capacity

Cooling system

Ignition system

PTO shaft rotation

429 450 438 mm

(16.9 17.7 17.2 in)

45.3 kg (99.9 lbs)

688.0 cm (41.97 cu-in)

[78.0 72.0 mm (3.07 2.83 in)]

16.0 kW (21.8 PS, 21.5 bhp) at 3,600 rpm

48.3 N·m (4.93 kgf·m, 35.6 lbf·ft) at

2,500 rpm

Forced air

CDI type magneto ignition

Counterclockwise

Length Width

Height

Dry mass [weight]

Engine type

Displacement

[Bore Stroke]

Net power

Max. Net torque

Engine oil capacity

Cooling system

Ignition system

PTO shaft rotation

429 450 438 mm

(16.917.717.2in)

45.3 kg (99.9 lbs)

688.0 cm (41.97 cu-in)

[78.0 72.0 mm (3.07 2.83 in)]

16.5 kW (22.4 PS, 22.1 bhp) at 3,600 rpm

48.3 N·m (4.93 kgf·m, 35.6 lbf·ft) at

2,500 rpm

Forced air

CDI type magneto ignition

Counterclockwise

The power rating of the engine indicated in this document is the

net power output tested on a production engine for the engine

model and measured in accordance with SAE J1349 at 3,600

rpm (Net Power) and at 2,500 rpm (Max. Net Torque). Mass

production engines may vary from this value.

Actual power output for the engine installed in the final machine

will vary depending on numerous factors, including the

operating speed of the engine in application, environmental

conditions, maintenance, and other variables.

The durability description is intended to provide you with

information relating to the engine’s emission durability period.

The descriptive term indicates the useful life period for the engine’s

emission control system. See your

Emission Control System

Warranty

for additional information.

Refer to page 10Spark plug gap

Idle speed

Valve clearance

(cold)

U. S.

Except

U. S.

Pump octane rating 86 or higher

Research octane rating 91 or higher

Pump octane rating 86 or higher

No other adjustments needed.

0.7 0.8 mm

(0.028 0.031 in)

1,400 150 rpm

ZFR5F (NGK)

IN: 0.08 0.02 mm

EX: 0.10 0.02 mm

1.5L(1.6USqt,1.3lmpqt)

1.7L(1.8USqt,1.5lmpqt)

1.5L(1.6USqt,1.3lmpqt)

1.7L(1.8USqt,1.5lmpqt)

1.5L(1.6USqt,1.3lmpqt)

1.7L(1.8USqt,1.5lmpqt)

Fuel

Engine oil

Spark plug

Maintenance

Unleaded gasoline (Refer to page 7 ).

SAE 10W-30, API SJ or later, for general use.

Refer to page 8.

Before each use:

Check engine oil level. Refer to page 8.

Check air filter. Refer to page 9.

First 20 hours:

Change engine oil. Refer to page 8.

Subsequent:

Refer to the maintenance schedule on page 7.

(Models certified for sale in California)

Without oil filter replacement:

With oil filter replacement:

Without oil filter replacement:

With oil filter replacement:

Without oil filter replacement:

With oil filter replacement:

4-stroke, overhead valve, 2 cylinders (90° V-Twin)

(in accordance with SAE J1349 )

See your authorized

Honda dealer

See your authorized

Honda dealer

Other specifications

09/07/07 20:38:32 32Z6L600_017

ENGLISH

Wiring Diagrams

2.7 A Charge Coil and With Control Box Type 17 A Charge Coil and With Control Box Type

2.7 A Charge Coil and Without Control Box Type 17 A Charge Coil and Without Control Box Type

Green

Red

White

Brown

Orange

Pink

Gray

ENGINE SWITCH

OIL LEVEL SWITCH

STARTER MOTOR

BATTERY

LEFT SPARK PLUG

MAIN FUSE

RIGHT SPARK PLUG

Black

Yellow

Blue

CHARGE COIL

LEFT IGNITION COIL

RIGHT IGNITION COIL

HOUR METER

CONTROL BOX

FUEL CUT SOLENOID

REGULATOR

RECTIFIER

(A)

(B)

(C)

(D)

(E)

(F)

(G)

(H)

(I)

(J)

(K)

(L)

(M)

(N)

Light blue

Light green

OFF

START

BATEIG LO ST

09/07/07 20:39:01 32Z6L600_018

ENGLISH

CONSUMER INFORMATION

WARRANTY AND DISTRIBUTOR/DEALER LOCATOR

INFORMATION

American Honda Motor Co., Inc.

Canada:

Honda Canada, Inc.

Australia:

Honda Australia Motorcycle and Power Equipment Pty. Ltd.

For European Area:

Honda Europe NV.

For European Area:

Canada:

United States, Puerto Rico, and U.S. Virgin Islands:

Australia:

United States, Puerto Rico, and U.S. Virgin Islands:

CUSTOMER SERVICE INFORMATION

United States, Puerto Rico, and U.S. Virgin Islands:

All Other Areas:

Honda’s Office

All Other Areas:

Power Equipment Division

Customer Relations Office

4900 Marconi Drive

Alpharetta, GA 30005-8847

Please visit www.honda.ca

for address information

Telephone: (888) 9HONDA9

(888) 946-6329

(877) 939-0909

Toll free

Toll freeFacsimile:

1954 1956 Hume Highway

Campbellfield Victoria 3061

Telephone: (03) 9270 1111

(03) 9270 1133Facsimile:

European Engine Center

http://www.honda-engines-eu.com

Visit our website: http://www.honda-engines-eu.com

or visit our website: www.honda.ca

Call (888) 9HONDA9

Visit our website: www.honda-engines.com

Call (03) 9270 1348

or visit our website: www.hondampe.com.au

Or telephone: (770) 497-6400, 8:30 am - 7:00 pm ET

Servicing dealership personnel are trained professionals. They

should be able to answer any question you may have. If you

encounter a problem that your dealer does not solve to your

satisfaction, please discuss it with the dealership’s management.

The Service Manager, General Manager, or Owner can help.

Almost all problems are solved in this way.

If you are dissatisfied with the decision made by the dealership’s

management, contact the Honda Regional Engine Distributor for

your area.

If you are still dissatisfied after speaking with the Regional Engine

Distributor, you may contact the Honda Office as shown.

If you are dissatisfied with the decision made by the dealership’s

management, contact the Honda Office as shown.

When you write or call, please provide this information:

Equipment manufacturer’s name and model number that the

engine is mounted on

Engine model, serial number, and type (see page )

Name of dealer who sold the engine to you

Name, address, and contact person of the dealer who services

your engine

Date of purchase

Your name, address and telephone number

A detailed description of the problem

Please contact the Honda distributor in your area for assistance.

09/07/07 20:39:33 32Z6L600_019

09/07/07 20:39:37 32Z6L600_020

La page charge ...

Intec VORTEC Beast Manuel utilisateur

Marque: Intec

Modèle: VORTEC Beast

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Intec VORTEC Beast User manual
español: Intec VORTEC Beast Manual de usuario

Intec VORTEC Beast Manuel utilisateur

Intec VORTEC Beast Manuel utilisateur

dans d''autres langues

Autres documents