RIDGID R4210 - Manuel utilisateur

To register your RIDGID

product, please visit:

http://register.RIDGID.com

Pour enregistrer votre produit de

RIDGID, s’il vous plaît la visite :

http://register.RIDGID.com

Para registrar su producto de

RIDGID, por favor visita:

http://register.RIDGID.com

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

10 in. SLIDING COMPOUND MITER SAW

SCIE À ONGLETS

COMBINÉS COULISSANTE

DE 254 mm (10 po)

SIERRA INGLETEADORA

COMPUESTA DESLIZANTE

DE 254 mm (10 pulg.)

R4210

WARNING: To reduce the

risk of injury, the user must read and

understand the operator’s manual

before using this product.

ADVERTENCIA: Para reducir

el riesgo de lesiones, el usuario debe

leer y comprender el manual del

operador antes de usar este producto.

AVERTISSEMENT :

Pour

réduire les risques de blessures,

l’utilisateur doit lire et veiller à bien

comprendre le manuel d’utilisation avant

d’employer ce produit.

TABLE OF CONTENTS

****************

 General Safety Rules .......................2-3

 Miter Saw Safety Rules ...................3-4

 Additional Safety Rules ...................4-5

 Symbols ..............................................6

 Electrical ............................................. 7

 Glossary of Terms ...............................8

 Features .........................................9-13

 Tools Needed ...................................14

 Loose Parts List ................................14

 Assembly .....................................15-24

 Operation .....................................25-38

 Maintenance ................................39-40

 Accessories ......................................40

 Guarantee .........................................41

 Parts Ordering / Service ..... Back Page

TABLE DES MATIÈRES

****************

 Règles de sécurité générales ..........2-3

 Règles de sécurité scie à onlgets ....3-4

 Règles de sécurité supplémentaires ...4-5

Symboles ............................................6

 Caractéristiques électriques ...............7

 Glossaire .............................................8

 Caractéristiques ............................9-13

Outils nécessaires ............................14

 Liste des pièces détachées ..............14

 Assemblage .................................15-24

 Utilisation .....................................25-38

 Entretien ......................................39-40

 Accessories ...................................... 40

 Garantie ............................................ 41

 Commande de pièces /

réparation ..........................Page arrière

ÍNDICE DE CONTENIDO

****************

Reglas de seguridad generales .......2-3

Reglas de seguridad sierra

ingleteadora ....................................3-4

Advertencias de seguridad

adicionales ......................................4-5

Símbolos ............................................6

Aspectos eléctricos ............................ 7

 Glosario de términos ..........................8

Características ..............................9-13

Herramientas necesarias ..................14

 Lista de piezas sueltas .....................14

Armado ........................................15-24

Funcionamiento ...........................25-38

Mantenimiento .............................39-40

Accessorios ...................................... 40

Garantía ............................................ 41

Pedidos de piezas /

servicio .......................... Pág. posterior

SAVE THIS MANUAL FOR

FUTURE REFERENCE

GUARDE ESTE MANUAL

PARA FUTURAS CONSULTAS

CONSERVER CE MANUEL

POUR FUTURE RÉFÉRENCE

2 - English

GENERAL SAFETY RULES

WARNING:

Read all safety warnings, instructions, illustra-

tions and specifications provided with this power

tool. Failure to follow all instructions listed below

may result in electric shock, fire and/or serious

injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

power tool.

WORK AREA SAFETY

Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases

or dust. Power tools create sparks which may ignite the

dust or fumes.

Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces,

such as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock if your body

is earthed or grounded.

Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged

or entangled cords increase the risk of electric shock.

When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

If operating a power tool in a damp location is

unavoidable, use a ground fault circuit interrupter

(GFCI) protected supply. Use of a GFCI reduces the

risk of electric shock.

PERSONAL SAFETY

Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a

power tool while you are tired or under the influence

of drugs, alcohol or medication. A moment of inattention

while operating power tools may result in serious personal

injury.

Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal

injuries.

Prevent unintentional starting. Ensure the switch is in

the off-position before connecting to power source

and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or

energising power tools that have the switch on invites

accidents.

Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal injury.

Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

Dress properly. Do not wear loose clothing or jewellery.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewellery or long hair can be caught

in moving parts.

If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

Do not let familiarity gained from frequent use of tools

allow you to become complacent and ignore tool

safety principles. A careless action can cause severe

injury within a fraction of a second.

POWER TOOL USE AND CARE

Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it was

designed.

Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from the

power tool before making any adjustments, changing

accessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the power tool

accidentally.

Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool

or these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused

by poorly maintained power tools.

3 - English

GENERAL SAFETY RULES

Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping

surfaces do not allow for safe handling and control of the

tool in unexpected situations.

SERVICE

Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Mitre saws are intended to cut wood or wood-like

products, they cannot be used with abrasive cut-off

wheels for cutting ferrous material such as bars, rods,

studs, etc. Abrasive dust causes moving parts such as

the lower guard to jam. Sparks from abrasive cutting will

burn the lower guard, the kerf insert and other plastic

parts.

Use clamps to support the workpiece whenever

possible. If supporting the workpiece by hand, you

must always keep your hand at least 100 mm from

either side of the saw blade. Do not use this saw to

cut pieces that are too small to be securely clamped

or held by hand. If your hand is placed too close to the

saw blade, there is an increased risk of injury from blade

contact.

The workpiece must be stationary and clamped or

held against both the fence and the table. Do not feed

the workpiece into the blade or cut ”freehand” in any

way. Unrestrained or moving workpieces could be thrown

at high speeds, causing injury.

Push the saw through the workpiece. Do not pull the

saw through the workpiece. To make a cut, raise the

saw head and pull it out over the workpiece without

cutting, start the motor, press the saw head down

and push the saw through the workpiece. Cutting on

the pull stroke is likely to cause the saw blade to climb

on top of the workpiece and violently throw the blade

assembly towards the operator.

Never cross your hand over the intended line of cut-

ting either in front or behind the saw blade. Supporting

the workpiece ”cross handed” i.e. holding the workpiece

to the right of the saw blade with your left hand or vice

versa is very dangerous.

Do not reach behind the fence with either hand closer

than 100 mm from either side of the saw blade, to

remove wood scraps, or for any other reason while

the blade is spinning. The proximity of the spinning saw

blade to your hand may not be obvious and you may be

seriously injured.

Inspect your workpiece before cutting. If the

workpiece is bowed or warped, clamp it with the

outside bowed face toward the fence. Always make

certain that there is no gap between the workpiece,

fence and table along the line of the cut. Bent or warped

workpieces can twist or shift and may cause binding on

the spinning saw blade while cutting. There should be no

nails or foreign objects in the workpiece.

Do not use the saw until the table is clear of all tools,

wood scraps, etc., except for the workpiece. Small de-

bris or loose pieces of wood or other objects that contact

the revolving blade can be thrown with high speed.

Cut only one workpiece at a time. Stacked multiple

workpieces cannot be adequately clamped or braced

and may bind on the blade or shift during cutting.

Ensure the mitre saw is mounted or placed on a level,

firm work surface before use. A level and firm work sur-

face reduces the risk of the mitre saw becoming unstable.

Plan your work. Every time you change the bevel or

mitre angle setting, make sure the adjustable fence

is set correctly to support the workpiece and will not

interfere with the blade or the guarding system. With-

out turning the tool ”ON” and with no workpiece on the

table, move the saw blade through a complete simulated

cut to assure there will be no interference or danger of

cutting the fence.

Provide adequate support such as table extensions,

saw horses, etc. for a workpiece that is wider or longer

than the table top. Workpieces longer or wider than the

mitre saw table can tip if not securely supported. If the

cut-off piece or workpiece tips, it can lift the lower guard

or be thrown by the spinning blade.

Do not use another person as a substitute for a table

extension or as additional support. Unstable support

for the workpiece can cause the blade to bind or the

workpiece to shift during the cutting operation pulling

you and the helper into the spinning blade.

The cut-off piece must not be jammed or pressed by

any means against the spinning saw blade. If confined,

i.e. using length stops, the cut-off piece could get wedged

against the blade and thrown violently.

MITER SAW SAFETY RULES

4 - English

MITER SAW SAFETY RULES

Always use a clamp or a fixture designed to properly

support round material such as rods or tubing. Rods

have a tendency to roll while being cut, causing the blade

to bite and pull the work with your hand into the blade.

Let the blade reach full speed before contacting the

workpiece. This will reduce the risk of the workpiece

being thrown.

If the workpiece or blade becomes jammed, turn the

mitre saw off. Wait for all moving parts to stop and

disconnect the plug from the power source and/or re-

move the battery pack. Then work to free the jammed

material. Continued sawing with a jammed workpiece

could cause loss of control or damage to the mitre saw.

After finishing the cut, release the switch, hold the

saw head down and wait for the blade to stop before

removing the cut-off piece. Reaching with your hand

near the coasting blade is dangerous.

Hold the handle firmly when making an incomplete cut

or when releasing the switch before the saw head is

completely in the down position. The braking action of

the saw may to be suddenly pulled downward, causing

a risk of injury.

 Save these instructions. Refer to them frequently and

use to instruct other users. If you loan someone this tool,

loan them these instructions also.

ADDITIONAL SAFETY RULES

 Use the proper extension cord. Make sure your extension

cord is in good condition. Use only a cord heavy enough

to carry the current your product will draw. An undersized

cord will cause a drop in line voltage resulting in loss of

power and overheating. A wire gauge size (A.W.G.) of at

least 14 is recommended for an extension cord 25 feet

or less in length. If in doubt, use the next heavier gauge.

The smaller the gauge number, the heavier the cord.

 Inspect tool cords periodically. If damaged, have

repaired by a qualified service technician at an authorized

service facility. Repair or replace a damaged or worn cord

immediately. Stay constantly aware of cord location and

keep it well away from the rotating blade.

 Inspect extension cords periodically and replace if

damaged.

 Polarized plugs. To reduce the risk of electric shock,

this tool has a polarized plug (one blade is wider than the

other). This plug will fit in a polarized outlet only one way.

If the plug does not fit fully in the outlet, reverse the plug.

If it still does not fit, contact a qualified electrician to install

the proper outlet. Do not change the plug in any way.

 Know your power tool. Read the operator’s manual

carefully. Learn the applications and limitations as well

as the specific potential hazards related to this tool.

 Always wear eye protection with side shields which

is marked to comply with ansi Z87.1 when using this

product. Failure to do so could result in objects being

thrown into your eyes, resulting in possible serious injury.

 Never stand on tool. Serious injury could occur if the tool

is tipped or if the cutting tool is unintentionally contacted.

 Keep guards in place and in good working order.

 Use the right direction of feed. Feed work into a blade,

cutter, or sanding spindle against the direction of rotation

of the blade, cutter, or sanding spindle only.

 Never leave tool running unattended. Turn the power

off. Don’t leave tool until it comes to a complete stop.

 Use only correct blades. Do not use blades with incorrect

size holes. Never use blade washers or blade bolts that

are defective or incorrect. The maximum blade capacity

of your saw is 10 in.

 Before making a cut, be sure all adjustments are

secure.

 Never touch blade or other moving parts during use.

 Double check all setups. Make sure blade is tight and not

making contact with saw or workpiece before connecting

to power supply.

 Firmly clamp or bolt your tool to a workbench or table

at approximately hip height.

 Make sure the miter table and saw arm (bevel

function) are locked in position before operating

your saw. Lock the miter table by pushing the

miter lock lever down. Lock the saw arm (bevel

function) by securely tightening the bevel lock knob.

 Never move the workpiece or make adjustment to any

cutting angle while the saw is running and the blade

is rotating. Any slip can result in contact with the blade

causing serious personal injury.

 Avoid awkward operations and hand positions where a

sudden slip could cause your hand to move into the blade.

ALWAYS make sure you have good balance. NEVER

operate your miter saw on the floor or in a crouched

position.

5 - English

ADDITIONAL SAFETY RULES

 Never stand or have any part of the body in line with the

path of the saw blade.

 Do not turn the motor switch on and off rapidly. This

could cause the saw blade to loosen and could create a

hazard. Should this ever occur, stand clear and allow the

saw blade to come to a complete stop. Disconnect your

saw from the power supply and securely retighten the

blade bolt.

 If any part of this miter saw is missing or should break,

bend, or fail in any way, or should any electrical component

fail to perform properly, shut off the power switch, remove

the miter saw plug from the power source and have

damaged, missing, or failed parts replaced before resuming

operation.

 Always turn off the saw before disconnecting it to avoid

accidental starting when reconnecting to power supply.

NEVER leave the saw unattended while connected to a

power source.

 This tool should have the following markings:

• To reduce the risk of injury, user must read and under-

stand the operator’s manual before using the miter saw.

• Keep hands and body out of the path of the saw blade.

Contact with the blade will result in serious injury.

• Do not operate saw without guards in place.

• Check guarding system to make sure it is functioning

correctly.

• Do not perform any operation freehand.

• Never reach around the saw blade.

• Turn off tool and wait for saw blade to stop before rais-

ing saw arm, moving workpiece, or changing settings.

• Disconnect the saw from the power source before

changing blade or servicing.

 Always carry the tool only by the carrying handle.

 This saw can tip over if the saw head is released suddenly

and the saw is not secured to a work surface. Always

secure this saw to a stable work surface before any use

to avoid serious personal injury.

 Always make sure the saw blade has clearance of

all obstructions before turning the saw on.

6 - English

SYMBOLS

Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation

of these symbols will allow you to operate the tool better and safer.

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s

Manual

To reduce the risk of injury, user must read and understand operator’s

manual before using this product.

Eye Protection

Always wear eye protection with side shields marked to comply

with ANSI Z87.1.

No Hands Symbol

Failure to keep your hands away from the blade will result in

serious personal injury.

Wet Conditions Alert Do not expose to rain or use in damp locations.

V Volts Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

min Minutes Time

Alternating Current Type of current

n

o

No Load Speed Rotational speed, at no load

Class II Construction Double-insulated construction

.../min Per Minute Revolutions, strokes, surface speed, orbits, etc., per minute

SYMBOL NAME

DESIGNATION/EXPLANATION

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates a hazardous situation, which, if not avoided, will result in death or

serious injury.

WARNING:

Indicates a hazardous situation, which, if not avoided, could result in death or

serious injury.

CAUTION:

Indicates a hazardous situation, that, if not avoided, may result in minor or

moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates information considered important, but

not related to a potential injury (e.g. messages relating to property damage).

7 - English

ELECTRICAL

DOUBLE INSULATION

Double insulation is a concept in safety in electric power

tools, which eliminates the need for the usual three-wire

grounded power cord. All exposed metal parts are isolated

from the internal metal motor components with protecting in-

sulation. Double insulated tools do not need to be grounded.

WARNING:

The double insulated system is intended to protect

the user from shock resulting from a break in the

tool’s internal wiring. Observe all normal safety

precautions to avoid electrical shock.

NOTE: Servicing of a product with double insulation requires

extreme care and knowledge of the system and should be

performed only by a qualified service technician. For service,

we suggest you return the tool to your nearest authorized

service center for repair. Always use original factory replace-

ment parts when servicing.

ELECTRICAL CONNECTION

This tool has a precision-built electric motor. It should be

connected to a power supply that is 120 volts, 60 Hz, AC

only (normal household current). Do not operate this tool

on direct current (DC). A substantial voltage drop will cause

a loss of power and the motor will overheat. If the tool does

not operate when plugged into an outlet, double-check the

power supply.

EXTENSION CORDS

When using a power tool at a considerable distance from

a power source, be sure to use an extension cord that has

the capacity to handle the current the product will draw. An

undersized cord will cause a drop in line voltage, resulting in

overheating and loss of power. Use the chart to determine

the minimum wire size required in an extension cord. Only

round jacketed cords listed by Underwriter’s Laboratories

(UL) should be used.

When working outdoors with a product, use an extension

cord that is designed for outside use. This type of cord is

designated with “WA” or “W” on the cord’s jacket.

Before using any extension cord, inspect it for loose or

exposed wires and cut or worn insulation.

**Ampere rating (on product data plate)

0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0

Cord Length Wire Size (A.W.G.)

25' 16 16 16 16 14 14

50' 16 16 16 14 14 12

100' 16 16 14 12 10 —

**Used on 12 gauge - 20 amp circuit.

NOTE: AWG = American Wire Gauge

WARNING:

Keep the extension cord clear of the working area.

Position the cord so that it will not get caught on

lumber, tools, or other obstructions while you are

working with a power tool. Failure to do so can

result in serious personal injury.

WARNING:

Check extension cords before each use. If dam-

aged replace immediately. Never use tool with a

damaged cord since touching the damaged area

could cause electrical shock resulting in serious

injury.

8 - English

GLOSSARY OF TERMS

Pilot Hole (drill presses and scroll saws)

A small hole drilled in a workpiece that serves as a guide

for drilling large holes accurately or for insertion of a scroll

saw blade.

Push Blocks (jointer planers)

Device used to feed the workpiece over the jointer planer

cutterhead during any operation. This aid helps keep the

operator’s hands well away from the cutterhead.

Push Blocks and Push Sticks (table saws)

Devices used to feed the workpiece through the saw blade

during cutting operations. When making a narrow rip cut

without a jig or similar cutting aid, always use a push stick

(not a push block). A push block can be used for narrow

ripping operations, if a jig or similar cutting aid is used.

These aids help keep the operator’s hands well away from

the blade.

Rabbet

A non-through cut positioned on the end or edge of the

workpiece which produces a square, two-sided notch or

trough in the workpiece.

Resaw (table saws and band saws)

A cutting operation to reduce the thickness of the workpiece

to make thinner pieces.

Resin

A sticky, sap-based substance that has hardened.

Revolutions Per Minute (RPM)

The number of turns completed by a spinning object in one

minute.

Ripping or Rip Cut (table saws)

A cutting operation along the length of the workpiece and

typically in the direction of the grain.

Riving Knife/Spreader/Splitter (table saws)

A metal piece, slightly thinner than the blade, which helps

keep the kerf open and also helps to prevent kickback.

Saw Blade Path

The area over, under, behind, or in front of the blade. As it

applies to the workpiece, that area which will be or has been

cut by the blade.

Snipe (planers)

Depression made at either end of a workpiece by cutter

blades when the workpiece is not properly supported.

Taper Cut

A cut where the material being cut has a different width at

the beginning of the cut from the end.

Through Sawing

Any cutting operation where the blade extends completely

through the thickness of the workpiece. This type of cut will

separate a single workpiece into two pieces.

Workpiece or Material

The item on which the operation is being done.

Worktable

Surface where the workpiece rests while performing a

cutting, drilling, planing, or sanding operation.

Anti-Kickback Pawls (radial arm and table saws)

A device which, when properly installed and maintained,

is designed to stop the workpiece from being kicked back

toward the front of the saw during a ripping operation.

Arbor

The shaft on which a blade or cutting tool is mounted.

Bevel Cut

A cutting operation made with the blade at any angle other

than 90° to the table surface.

Chamfer

A cut removing a wedge from a block so the end (or part of

the end) is angled rather than at 90°.

Compound Cut

A cross cut made with both a miter and a bevel angle.

Cross Cut

A cutting or shaping operation made across the grain or the

width of the workpiece.

Cutter Head (planers and jointer planers)

A rotating cutterhead with adjustable blades or knives. The

blades or knives remove material from the workpiece.

Dado Cut (table saws and compound sliding miter saws)

A non-through cut which produces a square, three-sided

notch or trough in the workpiece.

Featherboard (table saws)

A device used to help control the workpiece by guiding

it securely against the table or fence during any ripping

operation.

FPM or SPM

Feet per minute (or strokes per minute), used in reference

to blade movement.

Freehand

Performing a cut without the workpiece being guided by a

fence, miter fence, or other aids.

Gum

A sticky, sap-based residue from wood products.

Heel

Alignment of the blade to the fence.

Kerf

The material removed by the blade in a through cut or the

slot produced by the blade in a non-through or partial cut.

Kickback

A hazard that can occur when the blade binds or stalls,

throwing the workpiece in the direction of the spinning blade.

Miter Cut

A cutting operation made with the workpiece at any angle

to the blade other than 90°.

Non-Through Cuts (table saws and compound sliding

miter saws)

Any cutting operation where the blade does not extend

completely through the thickness of the workpiece. This is a

cut where the blade will not cut the workpiece into two pieces.

9 - English

FEATURES

PRODUCT SPECIFICATIONS

Blade Diameter .......................................................... 10 in.

Arbor Hole .................................................................5/8 in.

No Load Speed ......................................4,500 /min. (RPM)

Input ................................... 120, 60 Hz, AC Only, 15 Amps

Cutting Capacity with Miter at 0°/Bevel 0°:

Maximum nominal lumber sizes ................... 2 in. x 12 in.

or 4 in. x 6 in.

Cutting Capacity with Miter at 45°/Bevel 0°:

Maximum nominal lumber sizes ..................... 2 in. x 8 in.

Cutting Capacity with Miter at 0°/Bevel 45°:

Maximum nominal lumber sizes ................... 2 in. x 12 in.

Cutting Capacity with Miter at 45°/Bevel 45°:

Maximum nominal lumber sizes ..................... 2 in. x 8 in.

Crown Capacity

Nested Crown with Miter at 45° ......................... 6-5/8 in.

Baseboard Against the Fence ......................................6 in.

SWITCH

TRIGGER

BEVEL

LOCK KNOB

FENCE LOCK

KNOB

CARRYING

HANDLE

HEAD LOCK

BLADE WRENCH

STORAGE

DEPTH CONTROL KNOB

BEVEL DETENT

LEVER

LED

SWITCH

MITER DETENT

OVERRIDE

LEVER

Fig. 1

10 - English

FEATURES

Fig. 2

DUST

BAG

UPPER BLADE

GUARD

LOWER BLADE

GUARD

ADJUSTABLE

THROAT PLATE

MITER SCALE

MITER DETENT

BYPASS BUTTON

MITER LOCK

LEVER

MITER TABLE

SAW BASE

SLIDING MITER

FENCE

SLIDE

LOCK KNOB

WORK

CLAMP

SLIDE BAR

CONTROL

ARM

“D” HANDLE

“NO HANDS ZONE”

BOUNDARY LINE

“NO HANDS

ZONE” LABEL

“NO HANDS ZONE”

BOUNDARY LINE

TABLE LOCK

BUTTON

ROTATING

EXTENSION

TABLE

SLIDING MITER

FENCE

CROWN AND

BASEBOARD

SETTING LEVER

SLIDE

LOCK

KNOB

BASEBOARD

LOCK GROOVE

CROWN STOP

11 - English

FEATURES

Fig. 4

“D” HANDLE

HEAD

LOCK PIN

DEPTH CONTROL

KNOB

KNOW YOUR COMPOUND MITER SAW

See Figures 1 - 2.

The safe use of this product requires an understanding of

the information on the tool and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

10 in. BLADE

A 10 in. blade is included with the compound miter saw. It will

cut materials up to 3-1/2 in. thick or 12 in. wide, depending

upon the angle at which the cut is being made.

BEVEL DETENT LEVER

See Figure 3.

Loosen the bevel lock knob before using the bevel detent lever.

Tighten the knob after adjusting to lock the saw in place.

POSITION 1: (detent disengaged) Allows the blade to be

freely tilted either left or right for custom selection of bevel

cuts.

POSITION 2: (detent engaged) Allows you to easily find 0°,

15°, 22.5°, 33.9°, and 45° at indexed stops.

BEVEL LOCK KNOB

See Figure 3.

The bevel lock knob securely locks your compound miter

saw at desired bevel angles. Loosen the bevel lock knob to

release the saw, allowing the blade to be tilted either left or

right for bevel cuts. Tighten the knob to lock the saw in place.

CARRYING HANDLES

See Figure 4.

Carrying handles are located on the top of the saw arm

(D handle), at the top of the slide housing, and on the sides

of the saw base.

To transport: turn off and unplug the saw, lower saw arm

and lock it in the transport position, lock bevel and miter

lock levers, lock slide lock knob.

CROWN AND BASEBOARD SETTING LEVER

See Figure 2.

The crown and baseboard setting lever is helpful when mak-

ing miter cuts between 45° right and 45° left for tall crown

molding and vertical baseboard.

DEPTH CONTROL KNOB

See Figure 4.

The depth control knob is a guide for limiting downward

movement of the saw arm.

NOTE: Controlling depth of cut is necessary when rough

cutting a dado.

ELECTRIC BRAKE

An electric brake quickly stops blade rotation after the switch

trigger is released.

CARRYING

HANDLE

SIDE HANDLE

AREA

Fig. 3

BEVEL

ARM

1

2

BEVEL

LOCK KNOB

MITER

DETENT

OVERRIDE

LEVER

TIGHTEN

LOOSEN

BEVEL

DETENT

LEVER

MITER

DETENT

BYPASS

BUTTON

12 - English

Fig. 5

SLIDING

MITER FENCE

SLIDE

BAR

LOWER BLADE

GUARD

FEATURES

EXTENDED MITER CAPACITY

Rotating extension tables allow for miter cuts up to 70°.

HEAD LOCK PIN

See Figure 4.

The head lock pin is used for locking the saw arm in the

down position.

LED LIGHTING SYSTEM

The LED casts a shadow of the blade teeth onto the

workpiece for making precision cuts and predicts blade kerf

for blade cut line.

MITER DETENT OVERRIDE LEVER

See Figure 5.

The miter detent override lever allows you to make adjust-

ments to the miter angle without holding the miter detent

button. To use the miter detent override lever, unlock the

miter lock lever, push the miter detent bypass button (1) and

move the miter detent override lever down (2) to engage the

override.

MITER SCALE

Indexed miter stops have been provided at 0°, 15°, 22.5°,

31.6°, 45°, 60°, and 67.5°. The 0°, 15°, 22.5°, 31.6°, 45°, 60°,

and 67.5° indexed miter stops have been provided on both

the left and right side of the miter table.

SELF-RETRACTING LOWER BLADE GUARD

See Figure 5.

The lower blade guard is made of shock-resistant plastic that

provides protection from each side of the blade. It retracts

over the upper blade guard as the saw is lowered into the

workpiece.

SLIDE BAR

When unlocked, the saw arm will glide forward and back-

ward the length of the slide bar for cutting various workpiece

widths.

SLIDE LOCK KNOB

See Figure 5.

The slide lock knob locks and unlocks the sliding feature

of this tool.

SLIDE

LOCK

KNOB

1

2

13 - English

SPINDLE

LOCK BUTTON

SWITCH

TRIGGER

PADLOCK

Fig. 6

SWITCH

TRIGGER

LOCKOUT

LEVER

FEATURES

SLIDING MITER FENCES

See Figure 5.

The sliding miter fences help hold the workpiece securely

when making most cuts. The sliding feature allows for clear-

ance of the saw blade when making bevel or compound cuts.

Some cuts may require that the sliding fence be removed

completely to avoid interference between the fence and the

blade. Make sure the fence lock knob is tightened securely

to avoid interferance with the saw head.

Loosen the fence lock knob before attempting to slide the

fences or lift them for removal. Once the desired position of

the fence is determined, retighten the fence screw securely.

SPINDLE LOCK BUTTON

See Figure 6.

The spindle lock button locks the spindle (keeps the saw

blade from turning). Depress and hold the lock button only

while installing, changing, or removing the saw blade.

SWITCH TRIGGER

See Figures 6.

The saw will not start until you depress the trigger lockout

lever and squeeze the switch trigger. To prevent unauthor-

ized use of the compound miter saw, unplug the saw, and

lock the switch in the off position. To lock the switch, install

a padlock (not included) through the hole in the switch trig-

ger and make certain the switch is inoperable. If the switch

is still operable with the padlock installed, a padlock with a

larger shackle diameter must be used. Store the padlock key

in another location.

14 - English

WARNING:

The use of attachments or accessories not listed might be hazardous and could cause serious personal injury.

The following tools (not included) are needed for making adjustments:

COMBINATION SQUARE

TOOLS NEEDED

Fig. 7

COMBINATION WRENCH

10 mm, 13 mm

FRAMING SQUARE

PHILLIPS SCREWDRIVER

FLAT HEAD SCREWDRIVER

The following items are included with your miter saw:

 Dust Bag and Frame Assembly

 Work Clamp

 Blade

Fig. 8

LOOSE PARTS

WORK CLAMP

BLADE

SLIDING

MITER FENCES

HEX KEY

4 mm

DUST BAG/FRAME

ASSEMBLY

BLADE WRENCH/HEX KEY

 Blade Wrench/Hex Key

 Sliding Miter Fences

 Operator’s Manual (not shown)

15 - English

ASSEMBLY

UNPACKING

This product requires assembly.

 Carefully lift saw from the carton by the carrying handle

and the saw base, and place it on a level work surface.

WARNING:

Do not use this product if any parts on the Loose

Parts List are already assembled to your product

when you unpack it. Parts on this list are not

assembled to the product by the manufacturer and

require customer installation. Use of a product that

may have been improperly assembled could result

in serious personal injury.

 This saw has been shipped with the saw arm secured in

the down position. To release the saw arm, push down

on the top of the saw arm, cut the tie-wrap, and pull out

the lock pin.

WARNING:

The saw arm is spring loaded. Hold the handle

down to prevent it from snapping up when cutting

the tie-wrap. Failure to do so could result in

possible serious injury.

 Lift the saw arm by the D handle. Hand pressure should

remain on the saw arm to prevent sudden rise upon re-

lease of the tie-wrap.

 Inspect the tool carefully to make sure no breakage or

damage occurred during shipping.

 Do not discard the packing material until you have care-

fully inspected and satisfactorily operated the tool.

 The saw is factory set for accurate cutting. After assem-

bling it, check for accuracy. If shipping has influenced

the settings, refer to specific procedures explained in

this manual.

 If any parts are damaged or missing, please call

1-866-539-1710 for assistance.

WARNING:

If any parts are damaged or missing do not operate

this product until the parts are replaced. Use of this

product with damaged or missing parts could result

in serious personal injury.

WARNING:

Do not attempt to modify this product or create

accessories not recommended for use with this

tool. Any such alteration or modification is misuse

and could result in a hazardous condition leading

to possible serious personal injury.

WARNING:

Do not connect to power supply until assembly is

complete. Failure to comply could result in acci-

dental starting and possible serious personal injury.

WARNING:

Do not start the miter saw without checking for

interference between the blade and the miter fence.

Damage could result to the blade if it strikes the

miter fence during operation of the saw.

WARNING:

This saw can tip over if the saw head is released

suddenly and the saw is not secured to a work

surface. ALWAYS secure this saw to a stable work

surface before any use to avoid serious personal

injury.

16 - English

ASSEMBLY

TRACE HOLES AT THESE

LOCATIONS FOR HOLE PATTERN

Fig. 9

SAW

BASE

MOUNTING HOLES

See Figure 9.

WARNING:

Before starting any cutting operation, clamp, bolt or

screw your miter saw to a workbench or an approved

miter saw stand. If a miter saw stand is used, read

operator’s manual and follow the instructions for the

miter saw stand. Never operate your miter saw on

the floor or in a crouched position. Failure to heed

this warning can result in serious personal injury.

The compound miter saw should be mounted to a firm

supporting surface such as a workbench, mounting board,

or miter saw stand. The saw base has four mounting holes.

If using bolts or screws, they should be of sufficient length

to accommodate the saw base, lock washers, hex nuts, and

the thickness of the workbench or other mounting surface.

Tighten all bolts or screws securely.

The hole pattern for mounting to a workbench is shown in

figure 9. Carefully check the workbench after mounting to

make sure that no movement can occur during use. If any

tipping, sliding, or walking is noted, secure the workbench

to the floor before operating.

INSTALLING MITER FENCES

See Figure 10.

 Turn the fence lock knob counterclockwise to clear fixed

fence slots.

 Install the sliding miter fence. Lower fence into fence

slots. Be sure side of fence lines up flush with side of

fixed fence.

 Tighten fence lock knob securely. Repeat on other side.

USING THE DEPTH GUIDE

See Figure 11.

When used, the depth guide limits the downward travel of

the blade when cutting dadoes and other non-through cuts.

To use the depth guide:

 Unplug the saw.

 Rotate the depth stop outward.

 Loosen the lock nut.

 With the depth control knob touching the depth stop,

adjust the depth control knob by turning the knob until

the desired depth of cut is attained.

 Tighten the lock nut.

 A wooden spacer must be placed between the workpiece

and the fence to create a distance of 3-1/2 inches

between the workpiece and the fence for a consistent

depth of cut in the workpiece. Use the work clamp to

clamp the spacer and another suitable clamp to clamp

the workpiece. Make the slide cut at the desired depth.

See Figures 45 and 46.

Fig. 10

SLIDING MITER

FENCE

FENCE LOCK

KNOB

SLOT

17 - English

HEAD LOCK

DEPTH CONTROL

KNOB

ASSEMBLY

 Rotate the depth stop inward for normal through cuts.

NOTE: The depth stop must be pushed in before locking/

unlocking the saw arm.

LOCKING/UNLOCKING THE SAW ARM

See Figure 12.

When locking and unlocking the saw arm, it is not necessary

to loosen the depth control knob, however the depth stop

must be pushed in.

To unlock and raise the saw arm:

 Firmly grasp the “D” handle and apply downward pres-

sure while at the same time pulling the head lock pin out

and away from the saw housing.

 Release the head lock pin and slowly raise the saw arm.

To lock the saw arm:

 Firmly grasp the “D” handle and apply downward pres-

sure until head stops. Push in the head lock pin toward

the saw.

 Release the head lock pin allowing it to lock the saw into

place.

NOTE: Do not use saw to cut while in the locked position.

DUST BAG AND FRAME ASSEMBLY

See Figure 13.

To install the dust bag and frame assembly, slide the open

end of the frame assembly onto the exhaust port.

For efficient operation, empty the dust bag before it is half

full. This will permit better air flow through the bag.

NOTE: The exhaust port also accepts a 1-1/4 in. vacuum

hose and 1-1/4 in. wet/dry vacuum adaptors.

Fig. 13

DUST

BAG

END OF FRAME

ASSEMBLY

EXHAUST

PORT

Fig. 11

DEPTH

STOP

Fig. 12

HEAD LOCK

D HANDLE

LOCK

NUT

18 - English

ASSEMBLY

Fig. 14

INSTALLING/REPLACING THE BLADE

See Figure 14.

WARNING:

A 10 in. blade is the maximum blade capacity of

the saw. Never use a blade that is too thick to allow

outer blade washer to engage with the flats on the

spindle. Larger blades will come in contact with the

blade guards, while thicker blades will prevent the

blade bolt from securing the blade on the spindle.

Either of these situations could result in a serious

accident and can cause serious personal injury.

 Unplug the saw.

 Raise the saw arm.

 Rotate the lower blade guard to expose the blade bolt.

 Depress the spindle lock button and rotate the blade bolt

until the spindle locks.

 Using the hex end of the blade wrench, loosen and re-

move the blade bolt from the arbor.

NOTE: The blade bolt has left hand threads. Turn blade

bolt clockwise to loosen.

 Remove the outer blade washer.

NOTE: The inner blade washer is integrated into the

spindle and cannot be removed.

 Wipe a drop of oil onto inner blade washer and outer

blade washer where they contact the blade.

 Rotate the lower blade guard to expose the arbor.

 Fit saw blade inside blade guard and onto the arbor and

against the inner blade washer. The blade teeth point

downward at the front of saw as shown in figure 14.

 Replace the outer blade washer. The double “D” flats on

the blade washers align with the flats on the spindle.

 Depress spindle lock button and replace blade bolt.

NOTE: The blade bolt has left hand threads. Turn blade

bolt counterclockwise to tighten.

CAUTION:

Always install the blade with the blade teeth and

the arrow printed on the side of the blade pointing

down at the front of the saw. The direction of blade

rotation is also stamped with an arrow on the upper

blade guard.

 Tighten the blade bolt securely.

 Lower the blade guard.

 Raise and lower the saw arm to ensure the lower blade

guard functions correctly.

BLADE

LOWER BLADE

GUARD

BLADE

WRENCH

OUTER BLADE

WASHER

WITH DOUBLE

“D” FLATS

TO

LOOSEN

TO

TIGHTEN

BLADE

BOLT

ARBOR

OUTER

BLADE

WASHER

BLADE

BOLT

SPINDLE

LOCK BUTTON

SPINDLE

19 - English

ASSEMBLY

Fig. 15

ADJUSTABLE

THROAT PLATE

BLADE

WRENCH

Fig. 16

WORK

CLAMP

WORK CLAMP

SHAFT

WORK CLAMP

HOLE

WARNING:

Make sure the spindle lock button is not engaged

before reconnecting saw into power source. Never

engage spindle lock button when blade is rotating.

REMOVING/REPLACING THE ADJUSTABLE

THROAT PLATE

See Figure 15.

When squaring the saw blade, it may be necessary to

move the throat plate away from the blade. Once the saw’s

alignment has been confirmed, return the throat plate to its

original position. Never operate the saw without a throat

plate installed.

 Unplug the saw.

 Using the blade wrench provided, loosen the screws

securing the right side of the adjustable throat plate.

NOTE: The throat plate may be adjusted to (near) zero

clearance to support thin materials.

 Slide the throat plate away from the blade as far as

possible.

 Retighten the screws, being careful not to overtighten

which can cause the throat plate to bow or bend.

 Repeat the above steps for the left side of the throat plate.

INSTALLING THE WORK CLAMP

See Figure 16.

WARNING:

In some operations, the work clamp assembly

may interfere with the operation of the blade guard

assembly. Always make sure there is no interfer-

ence with the blade guard prior to beginning any

cutting operation to reduce the risk of serious

personal injury.

The work clamp provides greater control by clamping the

workpiece to the miter table. It also helps to prevent the

workpiece from creeping toward the saw blade. This is

helpful when cutting compound miters. Depending on the

cutting operation and the size of the workpiece, it may be

necessary to use a C-clamp instead of the work clamp to

secure the workpiece prior to making the cut. The work

clamp can be installed and used on either side of the blade.

To install the work clamp:

 Place the work clamp shaft in one of the holes located

behind the sliding miter fence.

 Rotate the knob on the work clamp to move it up or down

as needed.

20 - English

ASSEMBLY

Fig. 17

Fig. 18

MITER

LOCK

LEVER

Fig. 19

MITER LOCK

LEVER

MITER LOCK

NUT

UNDERSIDE OF MITER LOCK LEVER

MITER LOCK

SCREW

MITER

DETENT

BYPASS

BUTTON

MITER

LOCK NUT

MITER LOCK

SHOE

MITER LOCK

SCREW

SAW

BASE

ADJUSTING THE MITER LOCK

See Figures 17 - 18.

Prior to squaring the saw blade to the fence, ensure the

miter table moves and locks securely.

 Unplug the saw.

 Locate the miter lock nut, miter lock screw and miter lock

shoe on the rear underside of the saw.

To check the clamping force of the miter lock:

 Unplug the saw.

 Lift the miter lock lever and press the miter detent bypass

button to unlock the miter table.

 Rotate the miter table to an “unindexed” miter position

other than 0˚, 15˚, 22.5˚, 31.6˚, 45˚, 60˚, and 67.5˚.

 Push the miter lock lever down and attempt to move the

miter table. If the table moves easily when in the “locked”

position, adjust the miter lock screw.

 Using a 4 mm hex key, adjust the miter lock screw. Make

adjustments of one-quarter turn or less.

NOTE: Turning the miter lock screw clockwise will in-

crease the clamping force. Turning the miter lock screw

counterclockwise decreases the clamping force.

 After making the adjustment, test the clamping force.

To adjust miter table movement:

 Lift the miter lock lever, press the miter detent bypass

button, and move the miter table left to right. If the miter

table does not move freely, adjust the miter lock nut.

 Using the 4 mm hex key, hold the miter lock screw sta-

tionary and use the 13 mm combination wrench to adjust

the nut holding the miter lock shoe.

NOTE: Turning the miter lock nut clockwise will move the

shoe closer to the miter saw base and make it harder to

move the miter table. Turning the miter lock nut coun-

terclockwise will move the shoe farther away from the

base and make it easier to move the table.

 Adjust the miter lock nut until the shoe and miter saw

base are close but not in contact with each other.

 After making the adjustment, test the movement of the

miter table.

 Rotate the miter table to an “unindexed” miter position

other than 0˚, 15˚, 22.5˚, 31.6˚, 45˚, 60˚, and 67.5˚ and push

the miter lock lever down. Test the clamping force.

NOTE: It should take considerable force to move the

table in the locked position.

ADJUSTING THE MITER LOCK LEVER

See Figure 19.

 Unplug the saw.

 Lift the miter lock lever to unlock the miter table.

 If the miter lock lever is not parallel with the top of the

miter table, adjustments are needed.

La page charge ...

RIDGID R4210 - Manuel utilisateur

Ce manuel convient également à

RIDGID R4210 - Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents