Tripp Lite 3-Phase Metered 0U Power Distribution Unit Le manuel du propriétaire

1

Owner’s Manual

3-Phase Metered 0U

Power Distribution Unit

(Phase and Bank Measurements)

PDU3XMV6G32

(Series Number: AG-00BD)

Important Safety Instructions 2

Installation 3

Digital Display 5

Using the Digital Display 6

Features 12

Service 13

Warranty and 14

Product Registration

Español 15

Français 29

Русский 43

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

14-08-206-93338E.indb 1 10/9/2014 11:31:48 AM

2

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during

the installation, operation, and storage of this product. Failure to heed these

instructions and warnings may affect the product warranty.

• The PDU provides the convenience of multiple outlets, but DOES NOT provide surge or line

noise protection for connected equipment.

• The PDU is designed for indoor use only, in a controlled environment, away from excess

moisture, temperature extremes, conductive contaminants, dust or direct sunlight.

• Keep indoor ambient temperature between 32°F and 122°F (0°C and 50°C).

• The PDU must be installed by a qualiﬁed technician only.

• Do not attempt to mount the PDU to an insecure or unstable surface.

• Install in accordance with National Electrical Code standards. Be sure to use the proper

overcurrent protection for the installation, in accordance with the plug/equipment rating.

• Connect the PDU to an outlet that is in accordance with your local building codes and that is

adequately protected against excess currents, short circuits and earth faults.

• The electrical outlets supplying power to the equipment should be installed near the equipment

and easily accessible.

• Do not connect the PDU to an ungrounded outlet or to extension cords or adapters that

eliminate the connection to ground.

• Be sure to provide a local disconnect device on any models that are permanently installed

without a plug that is easily accessible.

• Never attempt to install electrical equipment during a thunderstorm.

• Individual equipment connected to the PDU should not draw more current than the individual

PDU’s outlet’s rating.

• The total load connected to the PDU must not exceed the maximum load rating for the PDU.

• Do not attempt to modify the PDU, input plugs or power cables.

• Do not drill into or attempt to open any part of the PDU housing. There are no user-serviceable

parts inside.

• Do not attempt to use the PDU if any part of it becomes damaged.

• Use of this equipment in life support applications where failure of this equipment can

reasonably be expected to cause the failure of the life support equipment or to signiﬁcantly

affect its safety or effectiveness is not recommended. Do not use this equipment in the

presence of a ﬂammable anesthetic mixture with air, oxygen or nitrous oxide.

14-08-206-93338E.indb 2 10/9/2014 11:31:48 AM

1-5

1-1

1-6

A

B

1-5

1-2 1-3 1-4

3

Installation

Mounting the PDU

Note: The illustrations may differ somewhat from your PDU model. Regardless of conﬁguration, the user must

determine the ﬁtness of hardware and procedures before mounting. The PDU and included hardware are designed

for common rack and rack enclosure types and may not be appropriate for all applications. Exact mounting

conﬁgurations may vary. Screws for attaching the mounting brackets to the PDU are included. Use only the screws

supplied by the manufacturer or their exact equivalent.

Note: Mounting buttons come preinstalled to the PDU for toolless mounting.

1-1

To mount the PDU using the pre-installed

mounting buttons, position the PDU as

desired in the rack enclosure, align the

buttons with the rack mounting slots,

and slide the PDU into position.

1-2

To attach the mounting brackets to the

PDU, remove the mounting buttons.

1-3

Attach the mounting brackets to the

PDU with the included screws.

1-4

Attach the PDU to a vertical rail in

your rack or rack enclosure. (Use the

mounting hardware that came with your

rack or rack enclosure to attach the

mounting brackets to the rail.)

1-5

To reinstall the mounting buttons for

toolless mounting, remove the mounting

brackets then install the mounting

buttons onto the PDU.

Note: Be sure to insert the 2 buttons into either

the upper hole at each end of the PDU or into

the lower hole at each end of the PDU.

1-6

To install the PDU with its outlets facing

the rear of the rack, use the included

PDUMVROTATEBRKT accessory. First,

attach the mounting button

A

to the

V-shaped bracket

B

using the included

screw and washer. Then, use the

button-mount slot to attach the bracket

to the PDU and the mounting button to

attach the PDU to the rack. The bracket

effectively repositions the mounting

brackets allowing for the PDU outlets to

face the rear of the rack.

14-08-206-93338E.indb 3 10/9/2014 11:31:50 AM

L3-N BANK 3L2-N BANK 2L1-N BANK 1

L1-N BANK 1

L2-N BANK 2

L3-N BANK 3

L1-N BANK 4

2-2

2-3

2-4

A

4

Installation

Connecting the PDU

2-1

The PDU3XMV6G32 is equipped with a 32A Red IEC 309 3P + N + E plug.

Model Name Input Plug

Max Input

Amps (Limited

by Input Cord

and Plug)

Input

Voltage

Range

Output

Voltage

Range Breakers

Cord

Length Outlets

PDU3XMV6G32

32A Red IEC 309

3P + N + E

32A 360-415V 208-240V

6 x Single

Pole, 20A

Branch-Rated

6 ft.

(1.8 m)

42 Total: 6 Banks

of (1) C19 and

(6) C13

2-2

Connect the input plug to your facility’s

compatible AC power source.

2-3

Connect your equipment’s input plugs to

the appropriate outlets on the PDU. The

LED near each bank illuminates when

the bank is ready to distribute live

AC power.

Note: It is recommended that you do not

connect a live load to the PDU. If the load you

intend to connect has an ON/OFF switch, please

turn the switch to OFF prior to connection.

2-4

Optional Cord Retention Procedure

Use the included C14 and C20 plastic

sleeves to secure plugs to receptacles.

Attach the sleeve to the plug, making

sure that the pull tabs

A

remain outside

the plug and that the ﬁt is secure. To

unplug equipment properly, use the pull

tabs to remove the plug and sleeve from

the receptacle.

14-08-206-93338E.indb 4 10/9/2014 11:31:51 AM

A

BC DE

5

Digital Display

A

3-Digit Display: Shows measured or calculated values such as Amperage, Kilowatts,

Voltage and Power Unbalance Percentage.

B

Arrow Buttons: Scroll through indicated Input, Bank, Power, Load Balance and Display

Brightness options using these buttons. A long press of the up or down arrow buttons allows

the user to skip to the next sequential measurement category.

C

Mode Button: When a menu option is selected using the Arrow Buttons, the Mode Button

scrolls through the sub-options within each category. Sub-options are shown by the

Indicator LEDs.

D

Indicator LEDs: Lit LED indicates which value is being displayed on the 3-digit screen.

Amps (A): When selected, the load on the selected Input Phase (L#) or

Load Bank (B#) is displayed in amps.

Wattage (kW): When selected, the load on the selected Load Bank (B#) or

Total Output Power (OP) is displayed in kW.

Voltage (V): Input Phase (L#) or Load Bank (B#) voltage is displayed.

Unbalanced Load (%UB): When lit, the display shows the unbalanced load

percentage deviance from the average measured value. A value that is zero or closest

to zero is desirable.

E

2-Digit Display: This display indicates which Input Phase (L#), Load Unbalance (UB),

Load Bank (B#) or Output Power (OP) option is selected.

Button Response Deﬁnitions:

Switch Action Control Function

Up

Pushbutton

Depress ½ sec Sequentially, moves up one selection in the menu.

Depress 3 sec Advances up to the next measurement category.

Down

Pushbutton

Depress ½ sec Sequentially, moves down one selection in the menu.

Depress 3 sec Advances down to the next measurement category.

Mode

Pushbutton

Depress ½ sec Displays available options for a given measurement category.

Depress 3 sec Selects the chosen available option for a given conﬁguration category.

14-08-206-93338E.indb 5 10/9/2014 11:31:51 AM

L3-N BANK 6L2-N BANK 5L1-N BANK 4L3-N BANK 3L2-N BANK 2L1-N BANK 1

L1-N BANK 1

L2-N BANK 2

L3-N BANK 3

L1-N BANK 4

L2-N BANK 5

L3-N BANK 6

Factory Use Only

L1-N L1-NL3-N L3-NL2-N L2-N

n

i 5.5

L i

n

i 5.5

L 2

n

i 5.5

L 3

4 0 0

L i

n

4 0 0

L 2

n

4 0 0

L 3

6

Digital Display

Load Bank Receptacle Location and Display References

PDU3XMV6G32

MODEL SILKSCREEN LABEL DESCRIPTION 2-DIGIT DISPLAY REFERENCE

PDU3XMV6G32

L1-N (Bank 1) B1

L2-N (Bank 2) B2

L3-N (Bank 3) B3

L1-N (Bank 4) B4

L2-N (Bank 5) B5

L3-N (Bank 6) B6

INPUT PHASE REFERENCE

INPUT PHASE REPORTED 2-DIGIT DISPLAY REFERENCE

L1-N L1

L2-N L2

L3-N L3

Using the Digital Display

Scrolling Through Input Phases and Options

(Measurement Category)

Press Mode button to toggle between options and data within a menu. A momentary press of the

arrow buttons switches between menus. A long press skips between measurement categories.

The scrolling pattern of the display is outlined below.

Input Phase 2

Input Phase 1

Amps Volts*

* Note: Voltages displayed are

phase-to-phase voltages (i.e.,

L1 display will indicate L1-L2

voltage).

14-08-206-93338E.indb 6 10/9/2014 11:31:52 AM

n

2 0

n

i 5.5

L i

n

i 5.5

L 2

n

i 5.5

L 3

4 0 0

L i

n

4 0 0

L 2

n

4 0 0

L 3

7

Using the Digital Display

Phase Imbalance %

Unbalanced Load Detect (Measurement Category)

Input Phase 2

Amps Volts*

Input Phase 3

Amps Volts*

To Unbalanced Load Detect

14-08-206-93338E.indb 7 10/9/2014 11:31:52 AM

n

1 0 .5

2. 1 8

2 0 8

1 0 .5

2. 1 8

2 0 8

n

1 0 .5

2. 1 8

2 0 8

8

Using the Digital Display

Scrolling Through Load Banks and Options (Measurement Category)

Scroll through the parameter display for each Load Bank using Mode and buttons.

Amps

Kilowatts

Volts

Bank #2

Bank #3

To Total

Output

Power

Amps Kilowatts Volts

Note: Continue for Load Banks 4-6.

14-08-206-93338E.indb 8 10/9/2014 11:31:53 AM

n

i.2 3

OP

n

nn

n

4

Y

3

I 2

n

I 2

9

Using the Digital Display

Press Mode button to toggle between options and data within a menu. A momentary press of the

arrow buttons switches between menus. A long press skips between measurement categories.

The scrolling pattern of the display is outlined below.

Total Output Power (Measurement Category)

Kilowatts

To Scroll

Function

Options

Press Mode button to toggle between options and data within a menu. A momentary press of the

arrow buttons switches between menus. A long press skips between measurement categories.

The scrolling pattern of the display is outlined below.

Scroll Function Options (Conﬁguration Category)

When enabled, the Auto Scroll function displays data for Input Phases, Load Unbalance and Load

Banks in 4-second intervals. Y indicates the function is enabled; N indicates that it is disabled.

Pressing any button interrupts the auto scroll function, allowing the user to navigate between

menu options. If no button is pressed, there is a 10 second timeout.

Note: Hold Mode button for 3 seconds to switch between options. The letter in the 2-digit display indicates the

selected option.

To LED

Brightness

14-08-206-93338E.indb 9 10/9/2014 11:31:54 AM

n

4

Y

3

I 2

n

I 2

n

4

Y

3

I 2

n

I 2

n

nn

n

4

Y

3

I 2

n

I 2

10

Using the Digital Display

LED Brightness and Color Scheme (Conﬁguration Category)

Hold the Mode button for 3 seconds to scroll through each option. The number in the 2-digit

display is deﬁned as: 1=25%; 2=50%; 3=75%; 4=100%

Bank Indicator LED Color Code Options (Conﬁguration Category)

Hold the Mode button for 3 seconds to switch between options.

The number in the 2-digit display indicates the selected scheme.

1=Standard, 2=Alternate

14-08-206-93338E.indb 10 10/9/2014 11:31:54 AM

nn

n

88

0 3.0

8 8 8

0 i

0 3.0

0 i

11

BANK INDICATOR LED DEFINITIONS:

LED Conﬁguration LED Color Bank Status Description

Standard

1

Off Off Bank power is absent

Green On Circuit breaker is on – Bank power is present

Yellow On

Bank has exceeded 80% of its current rating –

Bank power is present

Red Off

Bank is below the Low Voltage threshold –

Bank is disabled

Red Flashing Off Circuit breaker has tripped – Bank power is absent

Alternate

Off Off Bank power is absent

Red On Circuit breaker is on – Bank power is present

Red Flashing On

Bank has exceeded 80% of its current rating –

Bank power is present

Green Off

Bank is below the Low Voltage threshold –

Bank is disabled

Green Flashing Off Circuit breaker has tripped – Bank power is absent

1

This is the default conﬁguration.

Display Options

LED Test

Hold the Mode button for 3 seconds to test the display. For 5 seconds, all LEDs and display

segments will light green, while all Load Indicator LEDs will light yellow. Please visit

www.tripplite.com/support for issues with display segment or Indicator LED functionality.

Rotating the Display

At any point, pressing both of the arrow

buttons simultaneously and holding for

3 seconds rotates the 2-digit and 3-digit

displays.

Using the Digital Display

14-08-206-93338E.indb 11 10/9/2014 11:31:55 AM

12

Features

Outlets: During normal operation, the outlets distribute AC power to

connected equipment.

Bank Status LED: Once the unit is powered on, each Bank Status LED

will illuminate when the associated bank is ready to distribute live AC

power.

LED Color Bank Status Comments/Notes

Green On Normal operation.

Yellow On Bank’s current has exceeded 80% of its current

rating.

Red Off Bank’s voltage is below the Low Voltage

threshold.

Red Flashing Off Circuit breaker for this bank has tripped.

Off Off Bank is powered off.

Note: Colors noted here reﬂect standard LED conﬁguration. See chart on page 9 for

full LED color deﬁnitions.

C13

C19

Circuit Breaker: Each Load Bank is protected by a circuit breaker. If the

connected equipment load exceeds the Maximum Load Rating for those

banks of the PDU, the circuit breaker will trip. Disconnect excess load and

reset the breaker.

Note: Each breaker comes equipped with a push-to-reset guard to prevent

accidental breaker tripping. To turn off the breaker, insert a ﬂathead screwdriver into

the reset slot.

Mounting Brackets: Use these brackets as an alternate PDU mounting

method.

Mounting Buttons: Come pre-installed on the back side of the PDU and

are used for toolless mounting.

Note: Four additional mounting buttons are included for alternate rack styles.

Bank Status LED

Push-to-Reset Guard

PDUMVROTATEBRKT Mounting Accessory: Use these V-shaped

brackets to mount the PDU with its outlets facing the rear of the rack.

14-08-206-93338E.indb 12 10/9/2014 11:31:56 AM

13

Features

Ground Screw: Use this to connect any equipment that requires a

chassis ground.

C20 Plug Sleeve: (Optional) Use the included C20 plastic sleeves to

secure plugs to receptacles. Attach the sleeve to the plug making sure

that the pull tabs remain outside the plug and that the ﬁt is secure. To

unplug equipment properly, use the pull tabs to remove the plug and

sleeve from the receptacle.

RJ-45 Conﬁguration Port: For factory use only.

C14 Plug Sleeve: (Optional) Use the included C14 plastic sleeves to

secure plugs to receptacles. Attach the sleeve to the plug making sure

that the pull tabs remain outside the plug and that the ﬁt is secure. To

unplug equipment properly, use the pull tabs to remove the plug and

sleeve from the receptacle.

Service

Your Tripp Lite product is covered by the warranty described in this manual. A variety of Extended

Warranty and On-Site Service Programs are also available from Tripp Lite. For more information

on service, visit www.tripplite.com/support. Before returning your product for service, follow these

steps:

1. Review the installation and operation procedures in this manual to ensure that the service

problem does not originate from a misreading of the instructions.

2. If the problem continues, do not contact or return the product to the dealer. Instead, visit

www.tripplite.com/support.

3. If the problem requires service, visit www.tripplite.com/support and click the Product

Returns link. From here you can request a Returned Material Authorization (RMA) number,

which is required for service. This simple on-line form will ask for your unit’s model and

serial numbers, along with other general purchaser information. The RMA number, along

with shipping instructions will be emailed to you. Any damages (direct, indirect, special

or consequential) to the product incurred during shipment to Tripp Lite or an authorized

Tripp Lite service center is not covered under warranty. Products shipped to Tripp Lite or an

authorized Tripp Lite service center must have transportation charges prepaid. Mark the RMA

number on the outside of the package. If the product is within its warranty period, enclose

a copy of your sales receipt. Return the product for service using an insured carrier to the

address given to you when you request the RMA.

14-08-206-93338E.indb 13 10/9/2014 11:31:56 AM

14

Warranty and Product Registration

2- YEAR LIMITED WARRANTY

Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects

in material and workmanship for a period of 2 years from the date of initial purchase. If the product should

prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole

discretion. Service under this Warranty can only be obtained by your delivering or shipping the product (with all

shipping or delivery charges prepaid) to: Tripp Lite, 1111 W. 35th Street, Chicago, IL 60609 USA. Seller will pay

return shipping charges. Visit www.tripplite.com/support before sending any equipment back for repair.

THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE,

ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY

SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES,

INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE

WARRANTY PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND

CONSEQUENTIAL DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts,

and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above

limitations or exclusions may not apply to you. This Warranty gives you speciﬁc legal rights, and you may have

other rights which vary from jurisdiction to jurisdiction).

WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate

or safe for the use intended. Since individual applications are subject to great variation, the manufacturer makes

no representation or warranty as to the suitability or ﬁtness of these devices for any speciﬁc application.

PRODUCT REGISTRATION

Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered

into a drawing for a chance to win a FREE Tripp Lite product!*

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

FCC Notice, Class A

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct the interference

at his own expense. The user must use shielded cables and connectors with this equipment. Any changes or

modiﬁcations to this equipment not expressly approved by Tripp Lite could void the user’s authority to operate

this equipment.

Regulatory Compliance Identiﬁcation Numbers

For the purpose of regulatory compliance certiﬁcations and identiﬁcation, your Tripp Lite product has been assigned

a unique series number. The series number can be found on the product nameplate label, along with all required

approval markings and information. When requesting compliance information for this product, always refer to the

series number. The series number should not be confused with the marking name or model number of the product.

WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union)

Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations,

when customers buy new electrical and electronic equipment from Tripp Lite they are entitled to:

• Send old equipment for recycling on a one-for-one, like-for-like basis

(this varies depending on the country)

• Send the new equipment back for recycling when this ultimately becomes waste

The policy of Tripp Lite is one of continuous improvement. Speciﬁcations are subject to change without notice.

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

14-08-206-93338E.indb 14 10/9/2014 11:31:57 AM

15

Manual del propietario

Unidad de Distribución de Energía

Trifásica con Medidor Digital de 0U

(Mediciones de Fase y Banco)

PDU3XMV6G32

(Número de Serie: AG-00BD)

Instrucciones Importantes 16

de Seguridad

Instalación 17

Pantalla Digital 19

Usando la Pantalla Digital 20

Características 26

Servicio 27

Garantía 28

English 1

Français 29

Русский 43

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

14-08-206-93338E.indb 15 10/9/2014 11:31:59 AM

16

Instrucciones Importantes de Seguridad

CONSERVE ESTAS INSTRUCCIONES

Este manual contiene instrucciones y advertencias que deben seguirse durante

la instalación, operación y almacenamiento de este producto. La omisión en la

observancia de estas instrucciones y advertencias puede afectar la garantía

del producto.

• El PDU proporciona la conveniencia de múltiples tomacorrientes, pero NO proporciona

protección contra sobretensión o ruido en la línea para los equipos conectados.

• El PDU está diseñada solo para uso en interiores en un entorno controlado lejos de humedad

excesiva, temperaturas extremas, contaminantes conductivos, polvo o luz del sol directa.

• Mantiene la temperatura ambiente interior entre 32°F y 122°F (0°C y 50°C).

• El PDU debe ser instalado solamente por un técnico caliﬁcado.

• No intente instalar el PDU en una superﬁcie inestable o no segura.

• Instale de acuerdo con los estándares del Código Eléctrico Nacional (NEC). Asegúrese de

usar para la instalación la protección adecuada contra sobrecorriente, de acuerdo con la

especiﬁcación de la clavija o del equipo.

• Conecte el PDU a un tomacorriente que esté de acuerdo a los códigos locales de construcción

y que esté correctamente protegido contra corrientes excesivas, cortocircuitos y fallas de

conexión a tierra.

• Los tomacorrientes eléctricos que suministran energía al equipo deben instalarse próximos al

equipo y ser fácilmente accesibles.

• No conecte El PDU a un toma corriente que no esté a tierra o cables de extensión o

adaptadores que eliminen la conexión a tierra.

• Asegúrese de proporcionar un dispositivo local de desconexión, que sea fácilmente accesible,

en cualquier modelo que esté instalado permanentemente sin una clavija.

• Nunca intente instalar equipos eléctricos durante una tormenta eléctrica.

• El equipo individual conectado al PDU no debe consumir más corriente que la de la

especiﬁcación de cada tomacorriente individual del PDU.

• La carga total conectada al PDU no debe exceder la capacidad de carga máxima del PDU.

• No intente modiﬁcar el PDU, las clavijas de entrada o los cables de alimentación.

• No perfore ni intente abrir ninguna parte del gabinete del PDU. No tiene partes a las que el

usuario pueda dar servicio.

• No intente usar el PDU si se daña cualquier parte.

• El uso de este equipo en aplicaciones de soporte de vida en donde la falla de este equipo

pueda razonablemente hacer suponer que causará fallas en el equipo de soporte de vida

o afecte signiﬁcativamente su seguridad o efectividad, no está recomendado. No use este

equipo en la presencia de una mezcla anestésica inﬂamable con aire, oxigeno u óxido nitroso.

14-08-206-93338E.indb 16 10/9/2014 11:31:59 AM

1-5

1-1

1-6

A

B

1-5

1-2 1-3 1-4

17

Instalación

Instalación del PDU

Nota: Las ilustraciones pueden diferir un poco de su modelo de PDU. Sin importar la conﬁguración, el usuario debe

determinar la adecuación de los accesorios y procedimientos antes de la instalación. El PDU y accesorios incluidos

están diseñados para tipos comunes de racks y gabinetes y pueden no ser apropiados para todas las aplicaciones.

Las conﬁguraciones exactas de instalación pueden variar. Se incluyen los tornillos para instalar los soportes de

instalación al PDU. Use sólo los tornillos suministrados por el fabricante o su equivalente exacto.

Nota: El PDU tiene botones de instalación preinstalados para instalación sin herramientas.

1-1

Para montar el PDU utilizando los

botones pre-instaladas de montaje,

coloque el PDU como se desee en el

rack, alinear los botones con las ranuras

de montaje en rack, y deslice la PDU en

su posición.

1-2

Para ﬁjar los soportes de instalación al

PDU, retire los botones de instalación.

1-3

Fije los soportes de instalación al PDU

con los tornillos incluidos.

1-4

Acople el PDU a un riel vertical en su

rack o gabinete. (Use los accesorios de

instalación que vienen con su rack o

gabinete para acoplar los soportes de

instalación al riel).

1-5

Para reinstalar los botones de

instalación para instalación sin

herramienta, retírelos soportes de

instalación y entonces instale los

botones de instalación en el PDU.

Nota: Cerciórese de insertar los dos botones en

en cualquier oriﬁcio superior en cada extremo

del PDU o en el oriﬁcio inferior en cada

extremo del PDU.

1-6

Para instalar el PDU con los

tomacorrientes viendo hacia la parte

posterior del rack, use el accesorio

PDUMVROTATEBRKT incluido. Primero,

acople el botón de instalación

A

al

soporte con perﬁl en V

B

usando el

tornillo y arandela incluidos. Después,

use la ranura para instalación por

botón para acoplar el soporte al PDU

y el botón de instalación para acoplar

el PDU al rack. El soporte reposiciona

efectivamente los soportes de

instalación para que los tomacorrientes

del PDU apunten a la parte posterior del

rack.

14-08-206-93338E.indb 17 10/9/2014 11:32:00 AM

L3-N BANK 3L2-N BANK 2L1-N BANK 1

L1-N BANK 1

L2-N BANK 2

L3-N BANK 3

L1-N BANK 4

2-2

2-3

2-4

A

18

Instalación

Conexión del PDU

2-1

El PDU3XMV6G32 está equipado con una clavija IEC 309 de

3P + N + T, Roja de 32A.

Nombre del

Modelo

Clavija de

Entrada

Amperes

Máximos

de Entrada

(Limitado por el

Cable y Clavija

de Entrada)

Rango de

Voltaje de

Entrada

Rango de

Voltaje de

Salida Breakers

Longitud

del Cable Tomacorrientes

PDU3XMV6G32

IEC 309 de

3P + N + T,

Roja de 32A

32A 360-415V 208-240V

6 x Solo Polo,

Especiﬁcación

por Banco 20A

1.8 m

(6 pies)

42 Total:

6 Bancos de

(1) C19 y (6) C13

2-2

Conecte la clavija de entrada a la

fuente de alimentación de CA de su

instalación.

2-3

Conecte las clavijas de entrada de

sus equipos a los tomacorrientes

apropiados en el PDU. El LED próximo a

cada tomacorriente se ilumina cuando

el tomacorriente está listo para distribuir

energía de CA.

Nota: Se recomienda no conectar una

carga viva al PDU. Si la carga que pretende

conectar tiene un interruptor de encendido/

apagado, coloque por favor el interruptor en

apagado antes de la conexión.

2-4

Procedimientos Opcionales para

Sujeción del Cable

Use los manguitos plásticos C14 y

C20 para asegurar las clavijas a los

tomacorrientes. Instale el manguito a la

clavija, garantizando que las pestañas

A

permanezcan fuera de la clavija y que

el ajuste sea ﬁrme. Para desenchufar

correctamente el equipo, use las

pestañas para retirar del tomacorriente

la clavija y el manguito.

14-08-206-93338E.indb 18 10/9/2014 11:32:00 AM

A

BC DE

19

Pantalla Digital

A

Pantalla de 3 Dígitos: Muestra los valores medidos o calculados como Amperaje,

Kilowatts, Voltaje y Porcentaje de Desbalanceo de Potencia.

B

Botones de Flecha: Usando estos botones, se desplaza a través de las opciones indicadas

de Salida, Entrada, Banco, Potencia, Balance de Carga, Sensor Brillo de Pantalla. Una

presión prolongada de los botones de ﬂecha arriba o abajo permite al usuario saltar a la

siguiente categoría de medición secuencial.

C

Botón de Modo: Cuando se selecciona una opción de menú usando los Botones de

Flecha, el Botón de Modo se desplaza a través de las opciones secundarias dentro de cada

categoría. Las opciones secundarias se muestran mediante los LEDs indicadores.

D

LEDs Indicadores: El LED encendido indica qué valor se está mostrando en la pantalla de

3 dígitos.

Amperes (A): Cuando se selecciona, la carga en la fase de entrada (L#) seleccionada

o Banco de Carga (B#) se muestra en Amperes.

Potencia (kW): Cuando se selecciona, la carga en el Banco de Carga (B#)

seleccionada o Salio Potencia Total de Salida (OP) se muestra en kW.

Voltaje (V): Se muestra el voltaje en la Fase de Entrada (L#) o Banco de Carga (B#).

Desbalanceo de Carga (%UB): Al encender, la pantalla muestra la desviación del

porcentaje de desbalanceo de carga contra el valor medido promedio. Un valor que es

cero o tan cercano a cero como es deseable.

E

Pantalla de 2 Dígitos: Esta pantalla indica que opción de Fase de Entrada (L#),

Desbalanceo de Carga (UB), Banco de Carga (B#) o energía de salida (OP) está seleccionada.

Deﬁniciones de Respuesta de Botón:

Interruptor Acción Función de Control

Botón de Presión

Hacia Arriba

Oprimir ½ segundo Mueve secuencialmente hacia arriba una selección en el menú.

Oprimir 3 segundos Avanza hacia arriba a la siguiente categoría de medición.

Botón de Presión

Hacia Abajo

Oprimir ½ segundo Mueve secuencialmente hacia abajo una selección en el menú.

Oprimir 3 segundos Avanza hacia abajo a la siguiente categoría de medición.

Botón de Presión

de Modo

Oprimir ½ segundo

Muestra las opciones disponibles para una categoría de medición

dada.

Oprimir 3 segundos

Selecciona la opción disponible elegida para una categoría de

conﬁguración dada.

14-08-206-93338E.indb 19 10/9/2014 11:32:00 AM

L3-N BANK 6L2-N BANK 5L1-N BANK 4L3-N BANK 3L2-N BANK 2L1-N BANK 1

L1-N BANK 1

L2-N BANK 2

L3-N BANK 3

L1-N BANK 4

L2-N BANK 5

L3-N BANK 6

Factory Use Only

L1-N L1-NL3-N L3-NL2-N L2-N

n

i 5.5

L i

n

i 5.5

L 2

n

i 5.5

L 3

4 0 0

L i

n

4 0 0

L 2

n

4 0 0

L 3

20

Pantalla Digital

Ubicación del Receptáculo del Banco de Carga y Referencias de

Pantalla

PDU3XMV6G32

MODELO DESCRIPCIÓN DE ETIQUETA DE SERIGRAFÍA REFERENCIA DE PANTALLA DE 2 DÍGITOS

PDU3XMV6G32

L1-N (Banco 1) B1

L2-N (Banco 2) B2

L3-N (Banco 3) B3

L1-N (Banco 4) B4

L2-N (Banco 5) B5

L3-N (Banco 6) B6

REFERENCIA DE FASE DE ALIMENTACIÓN

FASE DE ALIMENTACIÓN REPORTADA REFERENCIA DE PANTALLA DE 2 DÍGITOS

L1-N L1

L2-N L2

L3-N L3

Usando la Pantalla Digital

Desplazándose a Través de Fases y Opciones de Entrada

(Categoría de Medición)

Oprima el botón de modo (Mode) para cambiar entre opciones y datos dentro de un menú. Una

presión momentánea de los botones de ﬂecha cambia entre menús. Una presión prolongada

salta entre categorías de mediciones. El patrón de desplazamiento en la pantalla se detalla a

continuación.

Fase de Entrada 2

Fase de Entrada 1

Amperes Volts*

* Nota: Los voltajes mostrados

son voltajes de fase a fase (i.e., la

pantalla L1 indicará voltaje entre

L1-L2).

14-08-206-93338E.indb 20 10/9/2014 11:32:01 AM

La page charge ...

Tripp Lite 3-Phase Metered 0U Power Distribution Unit Le manuel du propriétaire

Tripp Lite 3-Phase Metered 0U Power Distribution Unit Le manuel du propriétaire

dans d''autres langues

Documents connexes