Tripp Lite 3-Phase Switched 0U PDUs 8 Le manuel du propriétaire

1

Owner’s Manual

3-Phase Switched 0U Power

Distribution Units

208V MODELS

PDU3VSR6H50A • PDU3VSR6G60A

(Series Number: AG-0065) • (Series Number: AG-0063)

400V MODELS

PDU3XVSRHWA • PDU3XVSRHWB PDU3XVSR6G32A • PDU3XVSR6G32B

(Series Number: AG-0057) (Series Number: AG-0080)

PDU3XVSR6L2230 • PDU3XVSR6L2230B PDU3XVSR6G60A • PDU3XVSR6G60B

(Series Number: AG-0056) (Series Number: AG-0093)

PDU3XVSR6G30A • PDU3XVSR6G30B PDU3XVSR6G63A • PDU3XVSR6G63B

(Series Number: AG-0096) (Series Number: AG-0094)

Important Safety Instructions 2

Installation 3

Digital Display 8

Using the Digital Display 10

Features 16

Conﬁguration and Operation 18

Service 18

Warranty and Warranty Registration 19

Español 20

Français 39

Русский 58

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

PROTECT YOUR INVESTMENT!

Register your product for quicker service

and ultimate peace of mind.

You could also win an ISOBAR6ULTRA

surge protector—a $100 value!

www.tripplite.com/warranty

18-12-188-9332B8.indb 1 12/20/2018 5:19:13 PM

2

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during

the installation, operation, and storage of this product. Failure to heed these

instructions and warnings may affect the product warranty.

• The PDU provides convenient multiple outlets, but it DOES NOT provide surge or line noise

protection for connected equipment.

• The PDU is designed for indoor use only in a controlled environment away from excess

moisture, temperature extremes, conductive contaminants, dust or direct sunlight.

• Do not connect the PDU to an ungrounded outlet or to extension cords or adapters that

eliminate the connection to ground.

• The power requirement for each piece of equipment connected to the PDU must not exceed

the individual outlet’s load rating.

• The total power requirement for equipment connected to the PDU must not exceed the

maximum load rating for the PDU.

• Do not drill into or attempt to open any part of the PDU housing. There are no user-serviceable

parts inside.

• Do not attempt to modify the PDU, including the input plugs and power cables.

• Do not attempt to use the PDU if any part of it becomes damaged.

• Do not attempt to mount the PDU to an insecure or unstable surface.

• Use of this equipment in life support applications where failure of this equipment can

reasonably be expected to cause the failure of the life support equipment or to signiﬁcantly

affect its safety or effectiveness is not recommended. Do not use this equipment in the

presence of a ﬂammable anesthetic mixture with air, oxygen or nitrous oxide.

• Never attempt to install electrical equipment during a thunderstorm.

• Keep indoor ambient temperature between 32°F and 104°F (0°C and 40°C).

• Connect the PDU to an outlet that is in accordance with your local building codes and that is

adequately protected against excess currents, short circuits and earth faults.

• Do not attempt to open the PDU; there are no user-serviceable parts inside.

• The PDU must be installed by a qualiﬁed technician only.

18-12-188-9332B8.indb 2 12/20/2018 5:19:13 PM

1-1 1-2

1-4

1-3

1-5

A

B

3

Installation

Mounting the PDU

Note: The illustrations may differ somewhat from your PDU model. Regardless of conﬁguration, the user must

determine the ﬁtness of hardware and procedures before mounting. The PDU and included hardware are designed

for common rack and rack enclosure types and may not be appropriate for all applications. Exact mounting

conﬁgurations may vary. Screws for attaching the mounting brackets to the PDU are included. Use only the screws

supplied by the manufacturer or their exact equivalent.

Note: Mounting buttons come preinstalled to the PDU for toolless mounting.

1-1

To attach the mounting brackets to the

PDU, remove the mounting buttons.

1-2

Attach the mounting brackets to the

PDU with the included screws.

1-3

Attach the PDU to a vertical rail in

your rack or rack enclosure. (Use the

mounting hardware that came with your

rack or rack enclosure to attach the

mounting brackets to the rail.)

1-4

To reinstall the mounting buttons for

toolless mounting, remove the mounting

brackets then install the mounting

buttons onto the PDU. Position the PDU

as desired in the rack enclosure, align

the buttons with the rack mounting

slots, and slide the PDU into position.

Note: Be sure to insert the 2 buttons into either

the upper hole at each end of the PDU or into

the lower hole at each end of the PDU.

1-5

To install the PDU with its outlets facing

the rear of the rack, use the included

PDUMVROTATEBRKT accessory. First,

attach the mounting button

A

to the

V-shaped bracket

B

using the included

screw and washer. Then, use the

button-mount slot to attach the bracket

to the PDU and the mounting button to

attach the PDU to the rack. The bracket

effectively repositions the mounting

brackets allowing for the PDU outlets to

face the rear of the rack.

18-12-188-9332B8.indb 3 12/20/2018 5:19:14 PM

4

Installation

Connecting the PDU

2-1

Each 208V model is equipped with 1 of 2 different input plugs.

60A Blue IEC

309 3P+E

Model Name Input Plug

Max Input

Amps (Limited

by Input Cord

and Plug)

Input

Voltage

Output

Voltage Breakers

Cord

Length

Outlets

PDU3VSR6G60A

60A Blue IEC

309 3P+E

45A 208V 208V

6 x Double

Pole, 20A

Branch-Rated

6 ft.

(1.8 m)

18 Total; 6 Banks of

(2) C19 and (1) C13

PDU3VSR6H50A

HUBBLE

CS8365C

40A 208V 208V

6 x Double

Pole, 20A

Branch-Rated

6 ft.

(1.8 m)

18 Total; 6 Banks of

(2) C19 and (1) C13

HUBBLE

CS8365C

18-12-188-9332B8.indb 4 12/20/2018 5:19:14 PM

5

Installation

Each 400V model is equipped with 1 of 3 different input plugs.

63A Red IEC 309

3P+N+E

L22-30P 32A Red IEC 309

3P+N+E

Model Name Input Plug

Max Input

Amps (Limited

by Input Cord

and Plug)

Input

Voltage

Output

Voltage Breakers

Cord

Length

Outlets

PDU3XVSR6L2230

L22-30P 24A 400V 230V

6 x Single

Pole, 20A

Branch-

Rated

6 ft.

(1.8 m)

24 Total; 6 Banks of

(2) C19 and (2) C13

PDU3XVSR6L2230B

30 Total; 6 Banks of

(1) C19 and (4) C13

PDU3XVSR6G30A

30/32A Red

IEC 309

3P+N+E

24A 400V 230V

6 x Single

Pole, 20A

Branch-

Rated

6 ft.

(1.8 m)

24 Total; 6 Banks of

(2) C19 and (2) C13

PDU3XVSR6G30B

30 Total; 6 Banks of

(1) C19 and (4) C13

PDU3XVSR6G32A

30/32A Red

IEC 309

3P+N+E

32A 400V 230V

6 x Single

Pole, 20A

Branch-

Rated

6 ft.

(1.8 m)

24 Total; 6 Banks of

(2) C19 and (2) C13

PDU3XVSR6G32B

30 Total; 6 Banks of

(1) C19 and (4) C13

PDU3XVSR6G60A

60/63A Red

IEC 309

3P+N+E

35A 400V 230V

6 x Single

Pole, 20A

Branch-

Rated

6 ft.

(1.8 m)

24 Total; 6 Banks of

(2) C19 and (2) C13

PDU3XVSR6G60B

30 Total; 6 Banks of

(1) C19 and (4) C13

PDU3XVSR6G63A

60/63A Red

IEC 309

3P+N+E

40A 400V 230V

6 x Single

Pole, 20A

Branch-

Rated

6 ft.

(1.8 m)

24 Total; 6 Banks of

(2) C19 and (2) C13

PDU3XVSR6G63B

30 Total; 6 Banks of

(1) C19 and (4) C13

PDU3XVSRHWA

N/A 40A 400V 230V

6 x Single

Pole, 20A

Branch-

Rated

N/A

24 Total; 6 Banks of

(2) C19 and (2) C13

PDU3XVSRHWB

30 Total; 6 Banks of

(1) C19 and (4) C13

18-12-188-9332B8.indb 5 12/20/2018 5:19:14 PM

6

5

4

LOAD L2

BANK 1

3

1211

10

B4

B3

9

87

LOAD L1

BANK 2

LOAD L3

BANK 1

LOAD L2

BANK 1

STATUS

LINK

RESET

ENVIROSENSE

CONFIG

2-2

2-3

2-4

B

2-5

A

A B

6

Installation

2-2

Connect the input plug to your facility’s

compatible AC power source.

2-3

Connect your equipment’s input plugs to

the appropriate outlets on the PDU. The

LED near each outlet illuminates when

the outlet is ready to distribute live

AC power.

Note: It is recommended that you do not

connect a live load to the PDU. If the load you

intend to connect has an ON/OFF switch, please

turn the switch to OFF prior to connection.

2-4

Optional Cord Retention Procedure

Option 1 (Select Models): Use

the bridge lances located near each

receptacle to retain power cords. Tie

each equipment power cord to a bridge

lance by looping the cord and securing

it with one of the included cable ties

A

.

Make sure each cord can be unplugged

from the PDU without removing the

cable tie.

Option 2: Use the included C14 and

C20 plastic sleeves to secure plugs to

receptacles. Attach the sleeve to the

plug, making sure that the pull tabs

B

remain outside the plug and that the ﬁt

is secure. To unplug equipment properly,

use the pull tabs to remove the plug

and sleeve from the receptacle.

For Installation

Purposes Only

Hardwire Installations

(PDU3XVSRHWA & PDU3XVSRHWB models only)

2-5

These models do not come equipped

with an input cable. Conduit and

adapters are installed to the endplate

A

,

wires are channeled through the conduit

and adapters to the terminal block,

located behind the access plate

B

.

WARNING

Only qualiﬁed personnel should perform hardwire installations. Wire codes and

requirements differ from area to area. Be sure to conform to local electrical

requirements.

18-12-188-9332B8.indb 6 12/20/2018 5:19:16 PM

2-6

Remove Access Plate Screws

7

Installation

Networking the PDU

Your PDU can receive IP address assignments via DHCP server (dynamic) or static (manual)

addressing methods. See the SNMPWEBCARD installation guide on the included CD or visit

www.tripplite.com/manuals. If you are uncertain which method to use, contact your network

administrator for assistance before continuing the conﬁguration process.

Note: The MAC address of the PDU (12-digit string in this format: 000667xxxxxx) is printed on a label attached

to the PDU enclosure. For static IP address assignments, use the RJ-45 to DB9 conﬁguration cable (part

number 73-1243) included with the PDU.

2-6

To access the terminal block to make

input wire connections, remove the

access plate located on the back side of

the PDU.

Ground Terminal

X

Y

Z

N

18-12-188-9332B8.indb 7 12/20/2018 5:19:16 PM

A

BC DE

8

Digital Display

A

3-Digit Display: Shows measured or calculated values such as Amperage, Kilowatts,

Voltage, Power Unbalance Percentage, Temperature and Humidity.

B

Arrow Buttons: Scroll through indicated Outlet, Input, Bank, Power, Load Balance, Sensor

and Display Brightness options using these buttons. A long press of the up or down arrow

buttons allows the user to skip to the next sequential measurement category.

C

Mode Button: When a menu option is selected using the Arrow Buttons, the Mode Button

scrolls through the sub-options within each category. Sub-options are shown by the

Indicator LEDs.

D

Indicator LEDs: Lit LED indicates which value is being displayed on the 3-digit screen.

Amps (A): When selected, the load on the selected Input Phase (L#), Load Bank (B#)

or Outlet (##) is displayed in amps.

Wattage (kW): When selected, the load on the selected Load Bank (B#), Outlet (##)

or Total Output Power (OP) is displayed in kW.

Voltage (V): Input Phase (L#), Load Bank (B#) or Outlet (##) voltage is displayed.

Unbalanced Load (%UB): When lit, the display shows the unbalanced load

percentage deviance from the average measured value. The percentage for the phase

with the highest deviance is displayed.

Temperature (T): If Tripp Lite ENVIROSENSE is connected, the ambient temperature

will be displayed when this option is selected. The temperature is displayed in Celsius

by default, but can be switched to Fahrenheit.

Relative Humidity (%RH): If Tripp Lite ENVIROSENSE is connected, the relative

humidity percentage will be displayed when this option is selected.

E

2-Digit Display: This display indicates which Input Phase (L#), Load Balance (UB), Load

Bank (B#), Output Power (OP), Outlet (##) or Sensor (S#) option is selected.

18-12-188-9332B8.indb 8 12/20/2018 5:19:17 PM

65

4

LOAD L2

BANK 1

LOAD L1

BANK 1

3

21

LOAD L1

BANK 1

1211

10

LOAD L1

BANK 2

LOAD L3

BANK 1

9

87

LOAD L1

BANK 2

LOAD L3

BANK 1

LOAD L2

BANK 1

STATUS

LINK

RESET

ENVIROSENSE

1817

16

LOAD L3

BANK 2

LOAD L2

BANK 2

15

1413

LOAD L3

BANK 2

LOAD L2

BANK 2

CONFIG

STATUS

LINK

RESET

ENVIROSENSE

CONFIG

B1

B3

B5

B2

B4

B6

9

Digital Display

Load Bank Receptacle Location

Display References for 208V Models

LOAD BANKS REFERENCE

SILKSCREEN LABEL DESCRIPTION 2-DIGIT DISPLAY REFERENCE

L1-L2, BANK 1 B1

L2-L3, BANK 2 B2

L3-L1, BANK 3 B3

L1-L2, BANK 4 B4

L2-L3, BANK 5 B5

L3-L1, BANK 6 B6

INPUT PHASE REFERENCE

INPUT PHASE REPORTED 2-DIGIT DISPLAY REFERENCE

INPUT PHASE L1 – L2 L1

INPUT PHASE L2 – L3 L2

INPUT PHASE L3 – L1 L3

Button Response Deﬁnitions:

Conﬁguration

1

Switch Action Control Function

Standard

Up Pushbutton

Depress ½ sec

Sequentially, moves up one selection in

the menu.

Depress 3 sec

Advances up to the next measurement

category.

Down Pushbutton

Depress ½ sec

Sequentially, moves down one selection in

the menu.

Depress 3 sec

Advances down to the next measurement

category.

Mode Pushbutton

Depress ½ sec

Displays available options for a given

measurement category.

Depress 3 sec

Selects the chosen available option for a given

conﬁguration category.

Alternate

Up Pushbutton

Depress ½ sec

Sequentially, moves down one selection in

the menu.

Depress 3 sec

Advances down to the next measurement

category.

Down Pushbutton

Depress ½ sec

Sequentially, moves up one selection in the

menu.

Depress 3 sec

Advances up to the next measurement

category.

Mode Pushbutton

Depress ½ sec

Displays available options for a given

measurement category.

Depress 3 sec

Selects the chosen available option for a given

conﬁguration category.

1

Conﬁgured via Conﬁguration Category item “Outlet Indicator LED Color Code Options”.

18-12-188-9332B8.indb 9 12/20/2018 5:19:17 PM

i 5.5

L i

2 0 8

L i

i 5.5

L2

2 0 8

L2

i 5.5

L3

2 0 8

L3

10

Using the Digital Display

Scrolling Through Input Phases and Options

(Measurement Category)

Press Mode button to toggle between options and data within a menu. A momentary press of the

arrow buttons switches between menus. A long press skips between measurement categories.

The scrolling pattern of the display is outlined below. Note: Three dashes will be shown in the

3-digit display when the input phase voltage is unknown, due to abnormal tripped breaker

conditions.

Input Phase 1

Input Phase 2

Input Phase 3

Amps

Volts

To Unbalanced Load Detect

18-12-188-9332B8.indb 10 12/20/2018 5:19:17 PM

2 0

i 0.5 2. i 8

2. i 8

2 0 8

i 0.5 2 0 8

i.2 3

OP

11

Using the Digital Display

Press Mode button to toggle between options and data within a menu. A momentary press of the

arrow buttons switches between menus. A long press skips between measurement categories.

The scrolling pattern of the display is outlined below.

Unbalanced Load Detect (Measurement Category)

Scrolling Through Load Banks and Options (Measurement Category)

Scroll through Load Banks 2-6 using Mode button.

Amps

Kilowatts

Volts

Phase Imbalance %

To Total

Output

Power

Banks

#2, #3,

#4, #5

18-12-188-9332B8.indb 11 12/20/2018 5:19:18 PM

i 0.5 2. i 8

2. i 8

2 0 8

i 0.5 2 0 8

i.2 3

OP

0 i.5

0 i

0.3 i

2 0 8

30 30

2 0 8

30

0 i 0 i

0 i.5

12

Outlet

#2, #3,

#4…#30

Using the Digital Display

Press Mode button to toggle between options and data within a menu. A momentary press of the

arrow buttons switches between menus. A long press skips between measurement categories.

The scrolling pattern of the display is outlined below.

Total Output Power (Measurement Category)

Kilowatts

Scrolling Through Outlets and Options (Measurement Category)

Scroll through all available outlets using Mode button. Highest outlet number varies by model.

Amps

Kilowatts

Volts

To

Temperature

Readings

18-12-188-9332B8.indb 12 12/20/2018 5:19:18 PM

4 0

5 i 5 i

8 0

C F

C – F C – F

4

Y

3

I 2

13

Using the Digital Display

These options are only available when a sensor such as Tripp Lite’s ENVIROSENSE is attached

(sold separately). Press Mode button to toggle between options and data within a menu. A

momentary press of the arrow buttons switches between menus. A long press skips between

measurement categories. The scrolling pattern of the display is outlined below.

Scrolling Through Temperature Readings (Measurement Category)

Humidity (%RH)Temperature (T)

Temperature Unit Options (Conﬁguration Category)

3 Seconds

Hold Mode button for 3 seconds to

switch between options. The letter

in the 2-digit display indicates the

selected unit, C for Celsius and F for

Fahrenheit.

Press Mode button to toggle between options and data within a menu. A momentary press of the

arrow buttons switches between menus. A long press skips between measurement categories.

The scrolling pattern of the display is outlined below.

Scroll Function Options (Conﬁguration Category)

When enabled, the Auto Scroll

function displays data for

Input Phases, Load Unbalance

and Load Banks in 4-second

intervals. Y indicates the

function is enabled; N indicates

that it is disabled. Pressing any

button interrupts the auto scroll

function, allowing the user to

navigate between menu options.

If no button is pressed, there is

a 10 second timeout.

Note: Hold Mode button for 3

seconds to switch between options.

The letter in the 2-digit display

indicates the selected option.

To LED

Bright-

ness

18-12-188-9332B8.indb 13 12/20/2018 5:19:19 PM

4

Y

3

I 2

4

Y

3

I 2

4

Y

3

I 2

14

Using the Digital Display

Outlet Indicator LED Color Code Options (Conﬁguration Category)

Hold the Mode button for 3 seconds to switch between options.

The number in the 2-digit display indicates the selected scheme.

1=Standard, 2=Alternate

LED Brightness and Color Scheme (Conﬁguration Category)

Hold the Mode button for 3 seconds to scroll through each option. The number in the 2-digit

display is deﬁned as: 1=25%; 2=50%; 3=75%; 4=100%

18-12-188-9332B8.indb 14 12/20/2018 5:19:19 PM

i

88

i P

0 3.0

8 8 8

0 i

0 3.0

0 i

15

Using the Digital Display

Display Options

LED Test

Hold the Mode button for 3 seconds to test the display. All LEDs and display segments will light

green, while all Load Indicator LEDs will light yellow. Please visit www.tripplite.com/support for

issues with display segment or Indicator LED functionality.

Viewing the IP Address

At any point, pressing both of the arrow buttons simultaneously for 1/2

second displays the unit’s IP address in the 2-digit display.

OUTLET INDICATOR LED DEFINITIONS:

LED Conﬁguration LED Color Outlet Status Description

Standard

1

Off Off Outlet power is absent

Green On Circuit breaker is on – Outlet power is present

Yellow On

Outlet current has exceeded 80% of the outlet

current rating – Outlet power is present

Red Off

Outlet voltage is below the Low Voltage threshold –

Outlet power is absent

Red Flashing Off Circuit breaker has tripped – Outlet power is absent

Alternate

Off Off Outlet power is absent

Red On Circuit breaker is on – Outlet power is present

Red Flashing On

Outlet current has exceeded 80% of the outlet

current rating – Outlet power is present

Green Off Outlet is disabled - Outlet power is absent

Green Flashing Off Circuit breaker has tripped – Outlet power is absent

1

This is the default conﬁguration.

To Rotating the Display

18-12-188-9332B8.indb 15 12/20/2018 5:19:20 PM

i

88

i P

0 3.0

8 8 8

0 i

0 3.0

0 i

16

Using the Digital Display

Rotating the Display

At any point, pressing both of the arrow

buttons simultaneously and holding

for 3 seconds rotates the 2-digit and

3-digit displays.

Features

Outlets: During normal operation, the outlets

distribute AC power to connected equipment.

Outlet Status LED: Once the unit is powered on, each outlet individually

ramps up and each Outlet Status LED will illuminate when the associated

outlet is ready to distribute live AC power.

LED Color Outlet Status Comments/Notes

Green On Normal operation.

Yellow On Outlet current has exceeded 80% of the outlet

current rating.

Red Off Outlet voltage is below the Low Voltage threshold.

Flashing Red Off Circuit breaker for this bank has tripped.

Off Off Outlet is powered off.

Note: Colors noted here reﬂect standard LED conﬁguration. See chart on page 15

for full LED color deﬁnitions.

C13 C19

Circuit Breaker: There are 6 Load Banks, each protected by a circuit

breaker. If the connected equipment load exceeds the Maximum Load

Rating for that bank of the PDU, the circuit breaker will trip. Disconnect

excess load and reset the breaker.

Note: Each breaker comes equipped with a push-to-reset guard to prevent

accidental breaker tripping. To turn off the breaker, insert a ﬂathead screwdriver into

the reset slot.

Mounting Brackets: Use these brackets to mount the PDU.

Mounting Buttons: Come pre-installed on the back side of the PDU and

are used for toolless mounting. Note: Four additional mounting buttons

are included for alternate rack styles.

Outlet Status LED

Push-to-Reset Guard

18-12-188-9332B8.indb 16 12/20/2018 5:19:21 PM

CONFIG

A B

17

Features

SNMP Reset Button: Press the reset button for 3 seconds to reboot the

PDU’s network card. Rebooting the network card will not erase network

settings or interrupt AC power.

PS/2 Port: Use this port to connect a Tripp Lite ENVIROSENSE

environmental sensor to provide remote temperature/humidity monitoring

and a dry contact interface to control and monitor alarm, security and

telecom devices. Visit www.tripplite.com for ordering information. Note:

Do not connect a keyboard or mouse to this port.

Ground Screw: Use this to connect any equipment that requires a

chassis ground.

C20 Plug-lock Insert: (Optional) Use the included C20 inserts to secure

plugs to receptacles. Attach the insert to the plug making sure that the

pull tabs remain outside the plug and that the ﬁt is secure. To unplug

equipment properly, use the pull tabs to remove the plug and insert from

the receptacle.

RJ-45 Conﬁguration Port: Use this port to provide a direct terminal

connection to a computer with a terminal emulation program. An RJ-45 to

DB9 cable (part number 73-1243) is included with the PDU. If you need

a replacement cable, visit www.tripplite.com for ordering information.

Note: Conﬁguration options can found in the SNMPWEBCARD installation

guide on the included CD or at www.tripplite.com/manuals.

Ethernet Port: Use this RJ-45 jack to connect the PDU to the network

with a standard Ethernet patch cable. The Link LED

A

and Status LED

B

indicate several operating conditions, as shown in the table below. This

port is not compatible with PoE (Power Over Ethernet) applications.

Network Operating Conditions

A

Link LED Color

Off No Network Connection

Flashing Amber 100 Mbps Network Connection

Flashing Green 10 Mbps Network Connection

B

Status LED Color

Off Card Not Initialized

Steady or Flashing Green Card Initialized and Operational

Steady Amber Error - Card Not Initialized

PDUMVROTATEBRKT Mounting Accessory: Use these V-shaped

brackets to mount the PDU with its outlets facing the rear of the rack.

C14 Plug-lock Insert: (Optional) Use the included C14 inserts to secure

plugs to receptacles. Attach the insert to the plug making sure that the

pull tabs remain outside the plug and that the ﬁt is secure. To unplug

equipment properly, use the pull tabs to remove the plug and insert from

the receptacle.

18-12-188-9332B8.indb 17 12/20/2018 5:19:21 PM

A

B

18

Conﬁguration and Operation

Service

Remote Monitoring and Control

The PDU provides remote monitoring

A

,

outlet control

B

and more via Web browser,

telnet and SNMP-based Network Management

Systems. For more information about

conﬁguration and operation of the PDU via

thePowerAlert Web browser interface, refer to

the SNMPWEBCARD User’s Guide, included on

the CD-ROM bundled with the PDU.

Your Tripp Lite product is covered by the warranty described in this manual. A variety of Extended

Warranty and On-Site Service Programs are also available from Tripp Lite. For more information

on service, visit www.tripplite.com/support. Before returning your product for service, follow these

steps:

1. Review the installation and operation procedures in this manual to ensure that the service

problem does not originate from a misreading of the instructions.

2. If the problem continues, do not contact or return the product to the dealer. Instead, visit

www.tripplite.com/support.

3. If the problem requires service, visit www.tripplite.com/support and click the Product

Returns link. From here you can request a Returned Material Authorization (RMA) number,

which is required for service. This simple on-line form will ask for your unit’s model and

serial numbers, along with other general purchaser information. The RMA number, along

with shipping instructions will be emailed to you. Any damages (direct, indirect, special

or consequential) to the product incurred during shipment to Tripp Lite or an authorized

Tripp Lite service center is not covered under warranty. Products shipped to Tripp Lite or an

authorized Tripp Lite service center must have transportation charges prepaid. Mark the RMA

number on the outside of the package. If the product is within its warranty period, enclose

a copy of your sales receipt. Return the product for service using an insured carrier to the

address given to you when you request the RMA.

18-12-188-9332B8.indb 18 12/20/2018 5:19:21 PM

19

Warranty and Warranty Registration

2- YEAR LIMITED WARRANTY

Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects

in material and workmanship for a period of 2 years from the date of initial purchase. If the product should

prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole

discretion. Service under this Warranty can only be obtained by your delivering or shipping the product (with all

shipping or delivery charges prepaid) to: Tripp Lite, 1111 W. 35th Street, Chicago, IL 60609 USA. Seller will pay

return shipping charges. Visit www.tripplite.com/support before sending any equipment back for repair.

THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE,

ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY

SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES,

INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE

WARRANTY PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND

CONSEQUENTIAL DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts,

and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above

limitations or exclusions may not apply to you. This Warranty gives you speciﬁc legal rights, and you may have

other rights which vary from jurisdiction to jurisdiction).

WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate

or safe for the use intended. Since individual applications are subject to great variation, the manufacturer makes

no representation or warranty as to the suitability or ﬁtness of these devices for any speciﬁc application.

WARRANTY REGISTRATION

Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product.You’ll be

automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

FCC Notice, Class A

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct the interference

at his own expense. The user must use shielded cables and connectors with this equipment. Any changes or

modiﬁcations to this equipment not expressly approved by Tripp Lite could void the user’s authority to operate

this equipment.

Regulatory Compliance Identiﬁcation Numbers

For the purpose of regulatory compliance certiﬁcations and identiﬁcation, your Tripp Lite product has been assigned

a unique series number. The series number can be found on the product nameplate label, along with all required

approval markings and information. When requesting compliance information for this product, always refer to the

series number. The series number should not be confused with the marking name or model number of the product.

WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union)

Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations,

when customers buy new electrical and electronic equipment from Tripp Lite they are entitled to:

• Send old equipment for recycling on a one-for-one, like-for-like basis

(this varies depending on the country)

• Send the new equipment back for recycling when this ultimately becomes waste

The policy of Tripp Lite is one of continuous improvement. Speciﬁcations are subject to change without notice.

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

18-12-188-9332B8.indb 19 12/20/2018 5:19:22 PM

20

Manual del propietario

Unidades de Distribución de Energía

Trifásicas Controlables de 0U

MODELOS DE 208V

PDU3VSR6H50A • PDU3VSR6G60A

(Número de Serie: AG-0065) • (Número de Serie: AG-0080)

MODELOS DE 400V

Instrucciones Importantes de Seguridad 21

Instalación 22

Pantalla Digital 27

Usando la Pantalla Digital 29

Características 35

Conﬁguración y Operación 37

Servicio 37

Garantía 38

English 1

Français 39

Русский 58

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

PDU3XVSRHWA • PDU3XVSRHWB PDU3XVSR6G32A • PDU3XVSR6G32B

(Número de Serie: AG-0057) (Número de Serie: AG-0080)

PDU3XVSR6L2230 • PDU3XVSR6L2230B PDU3XVSR6G60A • PDU3XVSR6G60B

(Número de Serie: AG-0056) (Número de Serie: AG-0093)

PDU3XVSR6G30A • PDU3XVSR6G30B PDU3XVSR6G63A • PDU3XVSR6G63B

(Número de Serie: AG-0096) (Número de Serie: AG-0094)

18-12-188-9332B8.indb 20 12/20/2018 5:19:22 PM

La page charge ...

Tripp Lite 3-Phase Switched 0U PDUs 8 Le manuel du propriétaire

Tripp Lite 3-Phase Switched 0U PDUs 8 Le manuel du propriétaire

dans d''autres langues

Documents connexes