Simplicity 5901867 Manuel utilisateur

Marque: Simplicity

Modèle: 5901867

Catégorie: Tondeuses à gazon

Taper: Manuel utilisateur

Ce manuel convient également à

ZTR, S120 EXPORT

Not for

Reproduction

Not for

Reproduction

2 SnapperPro.com

Quick Setup List

Setup Procedures

 

Uncrate the unit.

 

Connect the battery cables.

 

Install the ground speed control levers.

 

Install the seat.

 

Install the roll bar on the unit.

 

Check engine oil level.

 

Check / Fill transmission oil level.

 

Check tire pressures.

 

Check mower blade bolt torque.

 

Check the deck lift rod timing.

 

Check and level the mower deck.

 

Check the mower deck drive belt.

 

Lubricate all grease and oil points.

 

Check / Add fuel.

 

Start the engine

PERFORM THE SAFETY CHECKS

 

Check forLOOSE HARDWARE.

 

Check allOPERATOR CONTROLS.

 

PerformSAFETY INTERLOCK SYSTEM CHECK.

Register Product

 

To register the product: log ontowww.thepowerportal.com, select the appropriate brand, click “Sales &

Marketing”, select the “Product Registration” link, and then select “New Product Registration”. Fill out and submit

the online product registration form.

Snapper Pro is a registered trademark of Briggs & Stratton

Corporation.

Not for

Reproduction

Introduction

The safety warnings provided in this guide and in the

operator’s manual included with the unit contain important

information that must be obeyed when assembling, setting-

up, operating, servicing, transporting, or storing the unit.

These warnings are highlighted by the safety alert triangle

symbol shown above, which signifies that an important safety

message is being provided.

You must read, understand, and follow these warnings

and instructions, and use safe shop and work practices

at all times while working on or around this unit and all

other outdoor power equipment.

SETUP PROCEDURES

Instructions in the Setup Procedures section provide the

information necessary to fully assemble, test, and prepare

the units described above for delivery to your customers. The

location of normal lubrication points are also included in this

section.

The QUICK SETUP LIST is provided in this booklet to help

you identify and check that the items have been performed.

ADJUSTMENT PROCEDURES

Additional information concerning general adjustment

procedures are included in this section.

Although all required lubrication and normal adjustments on

factory-assembled components are done at the factory, this

additional information is provided to assist you in ensuring

that each unit is delivered to the customer in proper working

order.

Not for

Reproduction

4 SnapperPro.com

Setup Procedures

The items in this section provide the information necessary

to fully assemble, test, and prepare the unit, that these

instructions were included with, for delivery to your customer.

The Quick Setup List provided on page 2 of this booklet

to help you identify and check that the items have been

performed.

Uncrating

1. Locate the transmission release levers (A, Figure 1)

underneath the engine deck of the machine and between

the two rear wheels on the transmission cradle (B).

There is one transmission release lever per transmission.

The transmission release lever opens and closes the

transmission bypass valve.

2. To open the transmission bypass valves (bypass position)

(C), move the transmission release lever up and pull it

towards the rear of the machine. When the second nut

(D) has passed through the hole, lower the rod down in

the slot so it will stay in the disengaged position. Repeat

the process for the other side of the zero-turn rider.

3. Push down on the parking brake lever to release the

parking brake.

4. Be sure there are no nails or sharp objects on the bottom

skid to puncture the zero-turn rider’s tires. Roll the zero-

turn rider forward off the bottom skid.

5. After moving the zero-turn rider, close the bypass valves

(run position) (E) by raising the transmission release

lever so that the back nut clears the slot, push the lever

towards the front of the machine. Repeat this process for

the other side of the zero-turn rider.

Connect the Battery Cables

WARNING

Battery acid can cause severe burns. Wear protective

gear when handling the battery.

Open flames and sparks can cause battery to explode.

BATTERY SAFETY RULES:

• Battery acid causes severe burns. Avoid contact with

skin.

• Wear eye protection when handling the battery.

• To avoid an explosion, keep flames and sparks away

from the battery, especially while charging.

• When installing the battery cables, connect the

positive (+) cable first and negative (-) cable last.

If not done in this order, the positive terminal can be

shorted to the frame by a tool.

1. Connect the red positive battery cable (B, Figure 2) to the

positive battery post.

2. Connect the black negative battery cable (A) to the

negative battery post.

Install the Ground Speed Control Levers

This procedure is only necessary if the ground speed control

levers are not factory-installed on your unit.

There is a LEFT-HAND (A, Figure 3) and a RIGHT-HAND

(B) control lever. When assembled to the base (C), the lever

base (D) should be pointing toward the rear of the machine as

shown in Figure 3.

Not for

Reproduction

1. Remove the ground speed control levers and mounting

hardware from the handle bar box.

2. Install the ground speed control levers (A & B) onto the

control lever base using the hardware (E) supplied in the

box. Prior to tightening the bolts, align the handles with

each other.

Install the Seat

This procedure is only necessary if the seat is not factory-

installed on your unit.

Some models are equipped with two sets of holes in the

seat plate that the seat can be installed in. Use the forward

set of holes to position the operator closer to the front of the

machine and the rear set of holes to position the operator

towards the rear of the machine. Determining what holes

to use is based on the preferred operating position of the

operator.

1. Unpack the seat.

2. Install the seat (A, Figure 4) onto the seat mount plate (B)

and secure with the 5/16 nylock flange nuts (C).

3. Connect the wire harness (D) to the seat switch (E) that is

located in the bottom of the seat.

Rigid Roll Bar Installation

If you are installing a rigid roll bar onto your unit follow these

instructions:

Install the Roll Bar to the Unit

The roll bar (A, Figure 5) is installed in roll bar pockets which

are part of the main frame of the unit and are located behind

the seat and in front of the engine on both sides of the unit.

The roll bar has safety decals installed on one side of the roll

bar and when the roll bar is installed on the unit the decals

Not for

Reproduction

6 SnapperPro.com

must be on the left side of the machine (as determined from

the operating position).

1. Unpack the roll bar and hardware from the box.

2. Make sure that no fuel lines, cables, or parts or the wire

harness are in the way of the roll bar pocket.

3. Have an assistant help you to lift the roll bar and place it

into the roll bar pockets.

4. Install the four (4) 1/2” bolts (B), and 1/2” washers (C)

through the roll bar and the frame of the unit and secure

in place with the 1/2” nylock flange nuts (D).

5. Tighten the installation hardware to 80 ft. lbs. (108 Nm) of

torque.

Folding Roll Bar Installation

If you are installing a folding roll bar onto your unit follow

these instructions:

Assemble the Roll Bar Retainer Pins

1. Unpack the roll bar and hardware from the box.

2. Lock the snap end (A, Figure 6) of the lanyard (B) through

the retainer pin handle (C) and snap together.

3. Install the lanyard anchor (D) onto the lanyard.

4. Install the hair pin (E) onto the loop end (F) of the lanyard

as shown in Figure 6.

Install the Roll Bar to the Unit

The roll bar assembly is installed in the roll bar pockets which

are part of the main frame of the unit and are located behind

the seat and in front of the engine on both sides of the unit.

1. Assemble the top loop (A, Figure 7) to the left upright

tube (B) and the right upright tube (C) by loosely installing

the 1/2 bolt (D), through the retainer pin assembly (E),

then through the hole in the top loop that is closest to the

rear of the machine, the upright tube, and then loosely

install the 1/2 side lock nut (F).

2. Fold the roll bar to the down position (A, Figure 8) and

lock in place using the retainer pins and hair pin clips (B).

3. Make sure that no fuel lines, cables, or parts of the wire

harness are in the way of the roll bar pockets.

4. From the bottom of the roll bar upright tube measure up

8” (G, Figure 7) and mark the distance with a marking tool

or a piece of tape. Repeat for other upright tube.

5. Install the roll bar into the roll bar pockets. The roll bar is

installed so that the safety decals are on the left side of

the machine (as determined from the operator’s position)

facing towards the front of the machine. When the mark

you made is even with the top of the roll bar pocket, the

holes are close to being lined up. If necessary, use a

dead blow hammer and drift pin to assist in lining up the

holes in the roll bar with the holes in the roll bar pocket.

Not for

Reproduction

6. It may be necessary to remove the rear tires of the zero-

turn rider to install the roll bar mounting bolts. To remove

the rear tires jack up the rear end of the zero-turn rider,

secure with jack stands, and then remove the rear tires

from the unit.

7. Loosely install the (4) 1/2” bolts (C, Figure 8), and 1/2”

washers (D), through the frame of the unit, the roll bar,

the outer frame of the unit, and loosely install the 1/2” lock

nuts (E).

8. Tighten the 1/2” hardware that secures the upright tubes

to the frame of the unit to 82 ft. lbs (108 Nm) of torque.

9. Tighten the 1/2” bolt and side lock nuts that secure the

top loop to the upright tubes. Do not over-tighten. The top

loop should pivot snugly with the retainer pins removed.

10. If the rear tires were removed from the unit re-install them

now. The lug nuts should be torqued to 90 ft. lbs. (122

Nm). Remove the jack stands from underneath the zero-

turn rider.

11. Raise the top loop to the upright position and install the

retainer pins and hair pin clips to secure the roll bar in the

raised position.

Check the Engine Oil Level

This model has different engine options. Use Figure 9 to

determine if your model is equipped with a Briggs & Stratton

Commercial Turf Series engine (A, Figure 9) or a Kawasaki

FS engine (B).

1. Use the dipstick (C) to check the engine oil level. If

necessary add engine oil through the engine oil fill (D).

Check the engine manufacturer’s owner’s manual for oil

recommendations.

Check / Fill Transmission Oil Level

This unit is equipped with two transmission oil tanks. One

transmission oil tank only supplies oil to one transmission.

The level of oil in both transmission tanks must be checked,

and if necessary, filled.

Oil Type: 20W-50 conventional detergent motor oil.

1. Locate the transmission oil tanks (A, Figure 10) by raising

the seat of the unit.

2. Check the oil level when the unit is cold. The oil should be

up to the "FULL COLD" mark (B). If the oil is below this

level, proceed to step #3.

3. Before removing the tank caps (C), make sure the area

around the tank cap and fill neck of the tank is free of

dust, dirt, or other debris. Remove the tank cap.

4. Add oil up the "FULL COLD" mark.

5. Reinstall the tank caps.

6. After adding oil to the tanks, it may be necessary to purge

air from the hydraulic system. If the unit is not driving

properly perform the Purging the Air from the Hydraulic

System procedure.

Check Tire Pressures

Tire pressure should be checked periodically, and maintained

at the levels shown in the chart. Note that these pressures

may differ slightly from the "Max Inflation" stamped on the

side-wall of the tires. The pressures shown in the chart

provide proper traction and extend tire life.

Tire Pressure

Front 25 psi (1,72 bar)

Rear 15 psi (1,03 bar)

Not for

Reproduction

8 SnapperPro.com

Check the Mower Blade Bolt Torque

WARNING

Avoid injury! Mower blades are sharp.

• Mower blades are sharp. For your personal safety, do

NOT handle mower blades with bare hands.

• Careless or improper handling of blades may result in

serious injury.

• Blade mounting bolts must each be installed with a

flat washer and then securely tightened. Torque blade

mounting bolts to 120 ft. lbs. (163 Nm).

1. Lock the mower deck in it's highest cutting position.

2. Check that the blades are installed with the tabs

pointing up (A, Figure11)towards the deck as showing

inFigure11.

3. Check that a flat washer (B) is installed between each

blade and the head of it's mounting bolt (C).

4. Wedge a wooden block (D) between the mower blade

and the mower deck housing to keep the mower blade

from turning. Torque each mower blade mounting bolt to

120 ft. lbs. (163 Nm).

Deck Lift Rod Timing Adjustment

Checking the Deck Lift Rod Timing

1. Park the machine on a flat, level surface. Disengage the

PTO, engage the parking brake, turn off the engine and

remove ignition key. Check that the tires are properly

inflated.

2. To check the lift rod timing, measure and record the

distance between the lift pivots (A, Figure 12) and the rod

pivots (B). Repeat for the other side of the unit.

3. If the measurements for the rods are equal, no further

adjustment is required. If the measurements are not equal

(greater than 1/8" (3.17 mm) difference), adjustment

is required, continue with Adjusting the Deck Lift Rod

Timing.

Adjusting the Deck Lift Rod Timing

1. Lock the deck lift pedal in the TRANSPORT position.

Remove the cutting height adjustment pin and lower the

mower deck.

2. To ensure that the deck is in the lowest position, push the

pedal by hand towards the rear of the unit and install the

height adjustment pin in the 3" (7.6 cm) position to hold in

place.

3. Block up the mower deck with 2 X 4's (B, Figure 13) until

all hanger chains are slack. The arrow (A) indicates the

front of the mower deck.

4. To adjust the deck lift rod (A, Figure 14), loosen the jam

nut (B) on the ball joint (C) then remove the 1/2" bolt (D),

washer (E), and 1/2" nylock flange nut (F) fastening the

ball joint (G) to the lift pivot arm (G). Turn the ball joint

clockwise to shorten the distance between the rod pivots

or counter-clockwise to lengthen the distance between

the rod pivots until the measurements between the lift

pivots and the rod pivots are the same. Reinstall the ball

Not for

Reproduction

joint and washer on the lift pivot arm and secure with

the 1/2" bolt and nylock flange nut that were previously

removed. Tighten the jam nut against the ball joint.

5. Remove the blocks from under the mower deck.

6. Remove the cutting height adjustment pin from in front of

the deck lift pedal arm. Lift the mower deck and reinstall

the adjustment pin in the desired mowing height.

Deck Leveling Adjustment

Before adjusting the deck level, the deck lift rod timing must

be checked and/or adjusted.

Determining if the Deck Leveling Needs to be

Adjusted

1. Park the unit on a flat, level surface. Disengage the PTO,

engage the parking brake, turn the ignition switch to OFF,

and remove the ignition key.

2. Lock the deck lift pedal in the TRANSPORT position.

Place the cutting height adjustment pin in the 4" position

and lower the deck lift pedal until the deck lift arm

contacts the cutting height adjustment pin.

3. Verify that the tires are inflated to the correct pressure.

4. Verify that the mower blades are flat, and not bent or

broken. A bent or broken blade must be replaced.

WARNING

Avoid Injury! Mower blades are sharp.

Always wear gloves when handling blades or working near

blades.

5. See Figure15. Position the outside mower blades so they

face front-to-back.

6. Measure the front tip (A, Figure15) of the blade from the

cutting edge to the ground.

7. Measure the rear tip (A) of the blade from the cutting

edge to the ground.

8. Repeat the process on the other side of the machine.

• the front measurements should equal 4" (10,2 cm).

• the rear measurements should equal 4-1/4" (10,8

cm)

If the measurements do not equal the measurements as

listed above, adjust the deck leveling.

Deck Leveling Adjustment

1. Place the deck height adjustment pin in the 4" (10,2 cm)

position.

2. Place 2 X 4 blocks under each corner of the mower deck

with the 3-1/2" sides being vertical. Place a 1/4" (0,64 cm)

thick spacer on the top of the rear blocks.

3. Loosen the nuts (D, Figure 16) and allow the front of the

deck to rest on the 2 X 4's. Slide the chains in the slots

until the chains are tight and tighten the nuts.

4. Loosen the nuts (C) and allow the rear of the deck to rest

on the 2 X 4's and 1/4" spacers. Slide the chains in the

slots until the chains are tight and tighten the nuts.

5. Repeat the process for the other side of the unit.

6. Remove all the blocks and spacers for under the mower

deck.

7. Perform the Determining if the Deck Leveling Needs to

be Adjusted procedure to verify that the deck has been

leveled correctly.

Not for

Reproduction

10 SnapperPro.com

• If the mower deck does not measure 4" (10,2 cm) in

the front and 4-1/4" (10,8 cm) in the rear, proceed

with step #8.

8. Loosen the jam nut (A) and turn the fine adjustment bolt

(B) to adjust the deck height.

• Turn the bolt clockwise to raise the deck.

• Turn the bolt counter-clockwise to lower the deck.

9. Once the desired measurements are achieved, re-tighten

the jam nut.

10. Repeat the process for the other side of the unit.

Deck Lift Assist Springs

Some models are equipped with deck lift assist springs (A,

Figure 17) that assist the operator in raising the mower deck

with the deck lift pedal. The deck lift assist springs are factory

set to provide optimal lifting performance.

Although it is fastened with a multi-position anchor, this is not

an adjustment point.

Do NOT attempt to adjust the spring length or lifting

performance will be compromised.

Check the Mower Deck Drive Belt

NOTICE To avoid damaging belt, do not pry over

pulleys.

1. Park the mower on a smooth level surface such as a

concrete floor. Disengage the PTO, engage the parking

brake, turn the ignition switch to OFF, and remove the

ignition key.

2. Lower the mower deck to it's lowest cutting position and

remove the mower deck guards and floor pan to gain

access to the mower deck drive belt.

3. Make sure that the V-side of the belt (A, Figures 18 & 19)

runs in the pulley grooves of the spindle pulleys (D & J)

and the PTO clutch pulley (G). Make sure that the back

side of the belt contacts the face of the front stationary

idler pulley(s) (H), rear stationary idler pulley (I), and

the adjustable idler pulley (F). Make sure that the belt is

correctly routed through the belt guides (E & K).

WARNING

Use extreme caution when rotating the idler arm with the

breaker bar, due to the increased tension in the spring

as the idler arm is being rotated. Injury may result if the

breaker bar is prematurely released while the spring is

under tension.

4. If the belt is not properly seated, use a 1/2” breaker bar

(B), and place the square end in the opening in the idler

arm (C).

5. Carefully rotate the breaker bar clockwise, pulling the

adjustable idler pulley away from the idler arm stop (L).

This will relieve the tension on the belt exerted from the

idler arm.

6. Re-seat the belt and carefully release the tension on the

breaker bar.

Not for

Reproduction

Check / Adjust the Mower Deck Drive Belt

Tensioning Spring Length

Mower Deck Drive Belt Tensioning Spring Length

Deck Size Measurement

52" 12" (30,5 cm)

61" 12" (30,5 cm)

1. Set the mower deck to the 3-1/2" (8.9 cm) cutting height.

2. Use the Mower Deck Drive Belt Tensioning Spring Length

chart to determine the correct spring length for your unit.

3. Measure the coil length (A, Figure 20) of the mower belt

idler tensioning spring (B). The measurement should

equal the measurement as indicated in the chart. If not,

continue with step #4..

4. Loosen the jam nut (C) on the eyebolt (D).

5. Turn the adjustment nut (E) until the measurement as

indicated in the chart is achieved.

6. Re-tighten the jam nut.

7. Re-install the mower deck guards and the floor pan.

8. Run the mower under no-load condition for about five (5)

minutes to break in the new belt.

Lubrication

Lubricate the unit at the locations shown in Figure 21, 22, 23

and as well as the following lubrication points.

Grease:

• front caster wheel axles and yokes

• deck lift pivot blocks

• mower deck spindles

Use grease fittings when present. Disassemble parts to apply

grease to moving parts when grease fittings are not installed.

Not all greases are compatible. Red grease (p/n 5022285)

is recommended. Automotive type, high temperature, lithium

grease may be used when this is not available.

Oil:

• ground speed control lever pivots & linkages

• parking brake shaft pivots

• seat plate pivots

• deck lift pivot points

• discharge chute hinge

Generally, all moving metal parts should be oiled where

contact is made with other parts. Keep oil and grease off belts

and pulleys. Remember to wipe fittings and surfaces clean

both before and after lubrication.

Not for

Reproduction

12 SnapperPro.com

Lubricate the Front Casters

Interval:Annually

1. Remove the 1/4-28 bolt (A, Figure24) screwed into the

caster and install a 1/4-28 grease fitting.

2. Grease the front caster.

3. Remove the 1/4-28 grease fitting and reinstall the 1/4-28

bolt.

4. Repeat the process for the other side of the machine.

Checking / Adding Fuel

WARNING

Gasoline is highly flammable and must be handled with

care. Allow engine to cool for at least 3 minutes before

refueling. Do not allow open flame, smoking or matches in

the area. Avoid over-filling and wipe up any spills.

To add fuel:

1. Remove the fuel cap (A, Figure25).

2. Fill the fuel tank to the bottom of the filler neck. This will

allow for fuel expansion.

Note: Do not overfill. Refer to your engine owner's

manual for specific fuel recommendations.

3. Install and hand tighten the fuel cap.

4. If your unit is equipped with two fuel tanks, repeat this

process to fill the other fuel tank.

NOTICE

Refer to your engine owner's manual for specific fuel

recommendations.

Starting the Engine - Carbureted Models

1. While standing on the operator's platform, engage

the parking brake, make sure that the PTO switch is

disengaged, and that the ground speed control levers are

in the NEUTRAL position.

2. A warm engine may not require choking. Set the

engine throttle control to FAST throttle position. Then fully

close the choke by pulling the knob OUT fully.

3. Insert the key into the ignition switch and turn it to

START.

4. After the engine starts, gradually open the choke (push

knob down fully). Reduce to half throttle speed and allow

engine to warm. Warm up the engine by running it for

atleast a minute before engaging the PTO switch or

driving the rider.

5. After warming the engine always operate the unit at FULL

throttle when mowing.

In the event of an emergency the engine can be stopped

by simply turning the ignition switch to STOP.

Not for

Reproduction

Perform the Safety Checks

WARNING

Disengage the PTO, stop the engine, set the parking

brake, and wait for moving parts to stop before leaving the

operator’s position for any reason.

If the unit does not pass a test, do not operate the unit. Under

no circumstance should you attempt to defeat the purpose of

the safety system.

Functional Tests

1. Check the unit for loose bolts, screws, nuts, etc.

2. Start the engine and check all the controls for proper

operation: ground speed control levers, parking brake,

throttle cable, electric PTO clutch, etc.

3. Stop the engine and check for fluid leaks: oil, fuel, and

hydraulic oil.

4. If any control fails to operate properly during testing or

seems to be out of adjustment, check and re-adjust it

according to the following Adjustment Procedures

section.

Safety Interlock System

This unit is equipped with safety interlock switches. These

safety systems are present for your safety, do not attempt

to bypass safety switches, and never tamper with safety

devices. Check their operation regularly.

Operational SAFETY Checks

Test 1 - Engine SHOULD NOT crank if:

• PTO switch is engaged, OR

• Parking brake is not engaged.

Test 2 - Engine SHOULD crank if:

• PTO switch is not engaged, AND

• Parking brake is engaged.

Test 3 - Engine should SHUT OFF if:

• Operator rises off seat with PTO engaged, OR

• Operator rises off seat with parking brake disengaged.

Test 4 - Blade Brake Check

Mower blades and mower drive belt should come to a

complete stop within seven (7) seconds after electric PTO

switch is turned off (or operator rises off seat). If mower drive

belt does not stop within seven (7) seconds, see your dealer.

NOTE: Once the engine has stopped, PTO switch must be

turned off, parking brake must be engaged, and the ground

speed control levers must be locked in the NEUTRAL position

after the operator returns to the seat in order to start the

engine.

WARNING

If the unit does not pass a safety test, do not operate it. See

your authorized dealer. Under no circumstance should you

attempt to defeat the purpose of safety interlock system.

Adjustment Procedures

If any control fails to operate properly during testing or seems

to be out of adjustment, check and re-adjust it according to

the following instructions.

Seat Adjustment

The seat can be adjusted forward and back. Move the lever

(A, Figure 26) towards the left, position the seat as desired,

and release the lever to lock the seat into position.

Ground Speed Control Lever Adjustment

The control levers can be adjusted in three ways. The

alignment of the control levers, the placement of the levers

(how close the ends are to one another) and the height of the

levers can be adjusted.

To Adjust the Handle Alignment

Loosen the mount bolts (A, Figure 27) and pivot the lever(s)

To Adjust the Handle Placement

Not for

Reproduction

14 SnapperPro.com

Loosen the jam nuts and adjust the placement bolt (B) in or

out to properly adjust the lever end spacing.

To Adjust the Handle Height

Remove the mounting hardware and reposition the handle

either up or down from its original position. You will need to

readjust the handle alignment as described above.

Speed Balancing Adjustment

If the rider veers to the right or left when the ground speed

control levers are in the maximum forward position, the top

speed of each of these levers can be balanced by turning the

adjustment bolt(s) (A, Figure28). Only adjust the speed of the

wheel that is traveling faster.

To Reduce the Speed of the Faster Wheel

1. Loosen the securing nut (B).

2. Turn the top speed adjustment boltcounter-clockwiseto

reduce the speed.

3. Retighten the securing nut when adjustment is complete.

WARNING

DO NOT adjust the tractor for a faster overall speed

forward or reverse than it was designed for.

Cutting Height Adjustment

The cutting height adjustment pin (A, Figure29) controls

the mower's cutting height. The cutting height is adjustable

between 1-1/2" (3,8 cm) and 5” (12,7 cm) in 1/4” (0,64 cm)

increments.

Note:Make sure that the pin is inserted into the holes in both

upper and lower plates of the pin box (B).

To set the cutting height at 1-1/2” (3,37 cm):

1. While sitting in the operator’s seat, press the deck lift

foot pedal (C) forward until it locks into the 5" (12,7 cm)

position.

2. Remove the cutting height adjustment pin from the hole

that it is installed in.

3. Press the deck lift foot pedal forward and then push the

lock lever (D) towards the right to release the lock.

4. Slowly release the deck lift foot pedal until it comes to

rest against the stationary pin (E) in the 1-1/2” (3,37 cm)

cutting height hole.

5. Place the cutting height adjustment pin in the storage

hole (F).

To set the cutting height in the range of 1-3/4” (4,40 cm)

and 4-3/4” (12,06 cm):

1. While sitting in the operator’s seat, press the deck lift foot

pedal forward until it locks into the 5" (12,7 cm) position.

2. Place the cutting height adjustment pin in the desired

cutting height.

3. Press the deck lift pedal forward and then push the lock

lever towards the right to release the lock.

4. Slowly release the deck lift foot pedal until it comes to rest

against the cutting height adjustment pin.

To set the cutting height at 5" (12,7 cm):

1. While sitting in the operator’s seat, press the deck lift foot

pedal forward until it locks into the 5" (12,7 cm) position.

2. Place the cutting height adjustment pin in any open

cutting height hole. The lift lock lever holds the mower

deck at 5" (12,7 cm) while cutting.

Neutral Adjustment

Each ground speed control lever on this unit is connected to

a transmission by a neutral linkage rod (A, Figure 30). The

Not for

Reproduction

neutral adjustment for this machine is achieved by changing

the length of the neutral linkage rods.

Determining if Adjustment is Necessary: If the tractor

"creeps" while the ground speed control levers are in the

NEUTRAL LOCKOUT position and the parking brake is

disengaged, then it is necessary to adjust the neutral linkage

rods.

Note:Perform this adjustment on a hard, level surface such

as a concrete floor.

1. Disengage the PTO, engage the parking brake and turn

off the engine.

2. There are two nuts (B & C) on the neutral linkage rod

(A). One nut is located by the ground speed control lever

(B) and the other nut is located by the transmission (C).

Loosen the nuts from the ball joints and turn the linkage

rod to adjust.

• If the machine creeps forward, turn the rod

clockwise (while standing at the rear of the machine

facing forward);

• If the machine creeps backwards, turn the rod

counter-clockwise (while standing at the rear of the

machine facing forward).

3. Lock the nuts against the ball joints when neutral is

achieved.

Note:The adjustment should not be performed while the

machine is running. It may take several attempts to achieve

neutral, depending on how much the machine creeps.

Return-to-Neutral Adjustment

Prior to performing this procedure the Neutral Adjustment

Procedure must be completed.

WARNING

To avoid serious injury, perform adjustments only with

engine stopped, key removed, and tractor parked on level

ground.

1. Position the ground speed control levers into the

NEUTRAL LOCKOUT position

2. Loosen the set collar (A, Figure31) on the neutral return

rod (B).

3. Position the set collar along the neutral return rod until it

contacts and very lightly compresses the neutral return

spring (C).

4. Move the ground speed control levers into the operating

position, pull rearward, and release.

5. Move the ground speed control levers out towards the

NEUTRAL LOCKOUT position.

• if the ground speed control lever aligns with the notch

in the neutral lock plate, adjustment is complete;

• if the ground speed control lever stops it's return

motion past the notch (while standing at the rear of

the machine), re-position the set collar so the neutral

return spring is less compressed.

• if the ground speed control lever stops it's return

motion before the notch (while standing at the rear

of the machine), re-position the set collar so that the

neutral return spring is more compressed.

6. Repeat the process as necessary until the ground speed

control lever aligns with the notch in the neutral lock

plate.

Note:It is important to note that after every adjustment of

the neutral return rod, the lever must be pulled rearward and

released to properly check the return-to-neutral position.

Neutral Lockout Adjustment

Prior to adjusting the neutral lockout, the neutral and return-

to-neutral must be properly adjusted.

1. Park the unit on a flat, level surface such as a concrete

floor. Disengage the PTO, engage the parking brake, turn

the ignition switch to OFF, and remove the ignition key.

2. Chock the wheels of the unit to prevent movement.

Not for

Reproduction

16 SnapperPro.com

3. Raise the seat to gain access to the neutral lockout

components.

4. Loosen the jam nuts (A, Figure 32) on the neutral lockout

bolts (B).

5. Engage the parking brake. The neutral lockout bolts will

enter the notches of the neutral lockout plates (C).

6. Position the neutral lockout bolts to the center of the

notches of the neutral lockout plates.

7. Re-tighten the jam nuts.

Purging the Air from the Hydraulic

System

Due to the effects air has on efficiency in hydraulic drive

systems, it is critical that it be purged from the system.

These purge procedures should be implemented any time a

hydraulic system has been opened to facilitate maintenance

or any additional oil has been added to the system.

The resulting symptoms of air in the hydraulic system may be:

• Noisy operation.

• Lack of power or drive after short term operation.

• High operation temperature and excessive expansion of

oil.

Before starting, make sure the transaxles/transmissions are

at the proper oil levels. If it is not, fill to the specifications

outlined in the Check / Fill Transmission Oil Level procedure.

Purging Air from the Hydraulic System:

1. Chock the front wheels to prevent the machine from

rolling. Raise the rear of the machine so that the vehicle’s

rear tires do not contact the ground. Position jack stands

under the rear bumper of the machine to secure it.

2. Open the transaxle’s bypass valves (see Uncrating for

the location and function of the bypass valves), start

the engine, release the parking brake, and slowly move

the zero-turn rider’s ground speed control levers in both

forward and reverse directions (5 to 6 times), as air is

purged from the unit, the oil level will drop.

3. Stop the engine and engage the parking brake.

4. Close the transaxle’s bypass valves, start the engine,

release the parking brake, and slowly move the zero-turn

rider’s ground speed control levers in both forward and

reverse directions (5 to 6 times), as air is purged from the

unit, the oil level will drop.

5. Stop the engine. Remove the jack stands from

underneath the machine.

6. Repeat the process detailed above but with the unit's

drive wheels on the ground. The procedure should be

performed in an area free of any objects or bystanders.

It may be necessary to repeat the process detailed above

until all the air is completely purged from the system. When

the transaxles/transmissions operate at normal noise levels

and move smoothly forward and reverse at normal speeds,

then the transaxles/transmissions are considered purged.

Parking Brake Adjustment

The parking brake mechanism consists of a two parking

brake cables, with a spring on both ends, that routes from the

transmission to the parking brake lever shaft. The position of

the parking brake cables and the compressed length of the

lower springs located by the transmissions are factory preset

and should not be changed for parking brake adjustment

procedures. The adjustment is achieved by changing the

compressed spring length of the upper parking brake springs.

1. Disengage the PTO, engage the parking brake, stop the

engine, and chock the tires.

2. Raise the seat plate.

3. Locate the parking brake springs (A, Figure33)



Not for

Reproduction

4. With the parking brake engaged measure the

compressed spring length. The spring should

measure2-1/4" (5,7 cm)when compressed.

5. If the spring length is not 2-1/4" (5,7 cm), release

the parking brake, and turn the adjustment nut (B) to

compress or release the spring.



CAUTION

Do not adjust the spring to be shorter than 2" (5,1 cm) when

compressed. This may damage the brake mechanism.

6. Engage the parking brake and re-measure the spring.

If this does not correct the braking problem, see your

dealer.

Not for

Reproduction

18 SnapperPro.com

Lista de instalación rápida

Procedimientos de configuración

 

Desempaque la unidad.

 

Conecte los cables de la batería.

 

Instale las palancas de control de velocidad de desplazamiento.

 

Instale el asiento.

 

Instale la barra antivuelco en la unidad.

 

Revise el nivel de aceite del motor.

 

Revise el nivel y complete el nivel de aceite de transmisión.

 

Revise la presión de los neumáticos.

 

Revise la torsión de los pernos de la cuchilla del cortacésped.

 

Revise la sincronización de la varilla de elevación de la cubierta.

 

Revise y nivele la cubierta del cortacésped.

 

Revise la correa de transmisión de la cubierta del cortacésped.

 

Lubrique todos los puntos de engrase y aceite.

 

Revise y agregue combustible.

 

Arranque el motor

REALICE LAS REVISIONES DE SEGURIDAD

 

Revise si hayPIEZAS METÁLICAS SUELTAS.

 

Revise todos losCONTROLES DEL OPERADOR.

 

Realice laREVISIÓN DEL SISTEMA DE INTERBLOQUEO DE SEGURIDAD.

Registre el producto

 

Para registrar el producto: inicie sesión enwww.thepowerportal.com, seleccione la marca correspondiente, haga

clic en “Ventas y marketing”, seleccione el enlace “Registro de producto” y después seleccione “Nuevo registro

de producto”. Complete y envíe el formulario de registro del producto en línea.

Snapper Pro es una marca comercial registrada de Briggs &

Stratton Corporation.

Not for

Reproduction

Introducción

Las advertencias de seguridad que se proporcionan en

esta guía y en el manual del operador que se incluye con

la unidad contienen información importante que se debe

obedecer cuando se monte, configure, opere, realice

mantenimiento, transporte o almacene la unidad.

Estas advertencias se destacan mediante el símbolo de

triángulo de alerta de seguridad que se muestra arriba, lo

que significa que se está proporcionando un mensaje de

seguridad importante.

Debe leer, comprender y seguir estas advertencias e

instrucciones, además de usar prácticas seguras en el

taller y en el trabajo en todo momento mientras trabaja

en o alrededor de esta unidad y de todos los equipos

motorizados para exteriores.

PROCEDIMIENTOS DE CONFIGURACIÓN

Las instrucciones de la sección Procedimientos de montaje

proporcionan la información necesaria para montar,

probar y preparar completamente las unidades descritas

anteriormente para entrega a los clientes. En esta sección

se incluye también la ubicación de los puntos de lubricación

normal.

Se proporciona una LISTA DE MONTAJE RÁPIDO en este

folleto para ayudarlo a identificar y verificar que se haya

realizado cada ítem.

PROCEDIMIENTOS DE AJUSTE

En esta sección se incluye información adicional con

respecto a los procedimientos generales de ajuste.

Aunque toda la lubricación y los ajustes normales requeridos

para los componentes montados en la fábrica se realizan

en la misma, esta información adicional se proporciona para

ayudarlo a garantizar que cada unidad se entregue al cliente

en buenas condiciones de funcionamiento.

Not for

Reproduction

20 SnapperPro.com

Procedimientos de

configuración

Los ítems de esta sección proporcionan la información

necesaria para ensamblar, probar y preparar la unidad por

completo, con las instrucciones que se incluyen, para su

entrega a su cliente.

Se proporciona una Lista de montaje rápido en la

página2 de este folleto para ayudarlo a identificar y

verificar que se haya realizado cada ítem.

Desempaque

1. Localice las palancas de desbloqueo de la transmisión

(A, Figura 1) ubicadas bajo la cubierta del motor de la

máquina y entre las dos ruedas posteriores del soporte

de la transmisión (B). Cada transmisión está equipada

con una palanca de liberación de transmisión. La palanca

de liberación de la transmisión abre y cierra las válvulas

de paso de la transmisión.

2. Para abrir la válvula de paso de la transmisión (posición

de paso) (C), mueva la palanca de liberación de la

transmisión hacia arriba y jale hacia la parte posterior de

la máquina. Cuando la segunda tuerca (D) pase a través

del orificio, baje la varilla a la ranura de modo que se

quede en la posición desactivada. Repita el proceso en el

otro lado del montable de giro cero.

3. Empuje la palanca de freno de estacionamiento hacia

abajo para soltar el freno de estacionamiento.

4. Asegúrese de que no hayan clavos ni objetos afilados en

la plataforma inferior que puedan perforar los neumáticos

del montablede giro cero. Haga avanzar el montablede

giro cero hacia adelante, fuera de la plataforma.

5. Después de mover el montablede radio de giro cero,

cierre las válvulas de paso (E) levantando la palanca

de liberación de la transmisión, de modo que la ranura

posterior salga de la ranura y empujando la palanca

hacia el frente de la máquina. Repita este proceso en el

otro lado del montablede giro cero.

Conexión de los cables de la batería

ADVERTENCIA

El ácido de la batería puede provocar quemaduras

graves. Use equipo de protección mientras manipula la

batería.

Las llamas abiertas y las chispas pueden provocar que

la batería explote.

REGLAS DE SEGURIDAD DE LA BATERÍA:

• El ácido de la batería provoca quemaduras graves.

Evite el contacto con la piel.

• Use protección para los ojos mientras manipula la

batería.

• Para evitar una explosión, mantenga las llamas y las

chispas alejadas de la batería, especialmente cuando

la esté cargando.

• Cuando instale los cables de la batería, conecte el

cable positivo (+) primero y al final el cable negativo

(-). Si no se hace en este orden, el terminal positivo

podría ser cortocircuitado a masa por una herramienta.

1. Conecte el cable positivo rojo de la batería (B, Figura 2)

al borne positivo de la batería.

2. Conecte el cable negro negativo de la batería (A) al

borne negativo de la batería.

Instalación de las palancas de control de

velocidad de desplazamiento

Este procedimiento solo es necesario si las palancas de

control de velocidad de desplazamiento no vienen instaladas

de fábrica en su unidad.

Hay una palanca de control IZQUIERDA (A, Figura 3) y una

palanca de control DERECHA (B). Cuando se montan en la

base (C), la base de la palanca (D) debe apuntar hacia la

La page charge ...

Simplicity 5901867 Manuel utilisateur

Marque: Simplicity

Modèle: 5901867

Catégorie: Tondeuses à gazon

Taper: Manuel utilisateur

Ce manuel convient également à

ZTR, S120 EXPORT

Télécharger le PDF

rapport

dans d''autres langues

English: Simplicity 5901867 User manual
español: Simplicity 5901867 Manual de usuario
português: Simplicity 5901867 Manual do usuário

Simplicity 5901867 Manuel utilisateur

Ce manuel convient également à

Simplicity 5901867 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents