Steinberg UR24C Startup Manual

Marque: Steinberg

Modèle: UR24C

Catégorie: Équipement musical supplémentaire

Taper: Startup Manual

1. IMPORTANT NOTICE: DO NOT MODIFY

THIS UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly

approved by Yamaha may void your authority,

granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to

accessories and/ or another product use only high

quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation

instructions. Failure to follow instructions could void

your FCC authorization to use this product in the

USA.

3. NOTE: This product has been tested and found to

comply with the requirements listed in FCC

Regulations, Part 15 for Class “B” digital devices.

Compliance with these requirements provides a

reasonable level of assurance that your use of this

product in a residential environment will not result

in harmful interference with other electronic

devices. This equipment generates/uses radio

frequencies and, if not installed and used according

to the instructions found in the users manual, may

cause interference harmful to the operation of other

electronic devices. Compliance with FCC

regulations does not guarantee that interference

will not occur in all installations. If this product is

found to be the source of interference, which can

be determined by turning the unit “OFF” and “ON”,

please try to eliminate the problem by using one of

the following measures:

Relocate either this product or the device that is

being affected by the interference.

Utilize power outlets that are on different branch

(circuit breaker or fuse) circuits or install AC line

filter/s.

In the case of radio or TV interference, relocate/

reorient the antenna. If the antenna lead-in is 300

ohm ribbon lead, change the lead-in to co-axial

type cable.

If these corrective measures do not produce

satisfactory results, please contact the local retailer

authorized to distribute this type of product. If you

can not locate the appropriate retailer, please

contact Yamaha Corporation of America, Electronic

Service Division, 6600 Orangethorpe Ave, Buena

Park, CA90620

The above statements apply ONLY to those

products distributed by Yamaha Corporation of

America or its subsidiaries.

* This applies only to products distributed by Yamaha Corporation of America. (class B)

FCC INFORMATION (U.S.A.)

COMPLIANCE INFORMATION STATEMENT

(Supplierʼs declaration of conformity procedure)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : 714-522-9011

Type of Equipment : USB AUDIO INTERFACE

Model Name : UR24C

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that may cause undesired

operation.

* This applies only to products distributed by Yamaha Corporation of America. (FCC SDoC)

UR24C Startup Guide 3

Contents

Message from the development team................................... 4

Package Contents................................................................... 4

PRECAUTIONS........................................................................ 5

Notice..................................................................................................... 6

Information............................................................................................. 7

Manuals.................................................................................... 8

Conventions in this manual ................................................... 8

TOOLS for UR-C...................................................................... 9

Yamaha Steinberg USB Driver .............................................................. 9

Steinberg UR-C Applications ................................................................. 9

Basic FX Suite ....................................................................................... 9

Preparation before using with a computer.......................... 10

Installing TOOLS for UR-C ................................................................... 10

Activating Basic FX Suite...................................................................... 12

Downloading Cubase AI ....................................................................... 12

Preparation before using with an iOS/iPadOS device........ 13

Apple accessories................................................................................. 13

Downloading Steinberg dspMixFx UR-C (mixing app).......................... 13

Downloading DAW app as necessary .................................................. 13

Setting up the power supply................................................. 14

Connecting the USB cable (bus-powered) ........................................... 14

Connecting the USB power adaptor or the USB mobile battery ........... 14

English

Message from the development team

4 UR24C Startup Guide

Message from the development team

Thank you for choosing the UR24C USB Audio Interface.

As a new lineup of the UR Series, three UR-C Series models were released in 2019. Now, we

are adding the new UR24C model.

Although the UR24C is a simple 2-in/4-out design, it features two powerful monitoring functions

(Monitor Mode DAW and Monitor Mode DJ) that allow you to cover a variety of completely

different usage scenarios with a single interface.

Monitor Mode “DAW” is convenient for producing music with a DAW such as Cubase.

For example, you can use direct monitoring and the built-in effects for latency-free recording.

It also has a loopback function that you can use when streaming your music live over the

Internet.

Monitor Mode “DJ” allows you to monitor two separate output signals at the same time on a

single pair of headphones. This mode is particularly useful if you use DJ software.

The UR-C series is gradually evolving along with the changing needs in audio production.

We will continue to make every effort to fully support the creative efforts of our users.

The Steinberg Hardware Development Team

Package Contents

The package of this product contains the following items. After opening the package, make

sure that it includes everything listed below.

UR24C main unit USB 3.0 cable (3.1 Gen1, Type-C to Type-A, 1.0 m)

UR24C Startup Guide (this book) CUBASE AI DOWNLOAD

INFORMATION

ESSENTIAL PRODUCT LICENCE

INFORMATION

PRECAUTIONS

UR24C Startup Guide 5

PRECAUTIONS

PLEASE READ CAREFULLY

BEFORE PROCEEDING

Please keep this manual in a safe place

for future reference.

This product is designed for music

production/recording. Do not use for any

purposes other than the one intended.

Those who are unfamiliar with handling or

those who can not handle according to this

manual such as children, should be

supervised by responsible persons to

ensure safety.

WARNING

Always follow the basic precautions

listed below to avoid the possibility of

serious injury or even death from

electrical shock, short-circuiting,

damages, fire or other hazards. These

precautions include, but are not limited

to, the following:

If you notice any abnormality

• If any of the following problems occur,

immediately unplug the USB cable from the

computer.

- The USB cable becomes frayed or

damaged.

- Unusual smells or smoke are emitted.

- Some object, or water has been dropped

into the product.

- There is a sudden loss of sound during use

of the product.

- Cracks or other visible damage appear on

the product.

Then have the product inspected or repaired

by qualified Yamaha service personnel.

Do not open

• This product contains no user-serviceable

parts. Do not attempt to disassemble the

internal parts or modify them in any way.

Water warning/Fire warning

• Do not expose the product to rain, use it

near water or in damp or wet conditions, or

place on it any containers (such as vases,

bottles or glasses) containing liquids which

might spill into any openings.

• Do not place any burning items or open

flames near the product, since they may

cause a fire.

Hearing loss

• Before turning the power of all devices on or

off, make sure that all volume levels are set

to the minimum. Failing to do so may result in

hearing loss, electric shock, or device

damage.

• When turning on the AC power in your audio

system, always turn on the power amplifier

LAST, to avoid hearing loss and speaker

damage. When turning the power off, the

power amplifier should be turned off FIRST

for the same reason.

• Do not use headphones for a long period of

time at a high or uncomfortable volume level,

since this can cause permanent hearing

loss. If you experience any hearing loss or

ringing in the ears, consult a physician.

CAUTION

Always follow the basic precautions

listed below to avoid the possibility of

physical injury to you or others. These

precautions include, but are not limited

to, the following:

Location and connection

• Do not place the product in an unstable

position or a location with excessive

vibration, where it might accidentally fall over

and cause injury.

• Keep this product out of reach of children.

This product is not suitable for use in

locations where children are likely to be

present.

PA_en_11 1/2

PRECAUTIONS

6 UR24C Startup Guide

• Do not place the product in a location where

it may come into contact with corrosive

gases or salt air. Doing so may result in

malfunction.

• Before moving the product, remove all

connected cables.

Maintenance

• Remove the USB cable from the computer

when cleaning the product.

Handling caution

• Do not rest your weight on the product or

place heavy objects on it.

Notice

To avoid the possibility of malfunction/

damage to the product, damage to data, or

damage to other property, follow the notices

below.

 Handling and maintenance

• Do not use the product in the vicinity of a TV,

radio, or other electric products. Otherwise,

the product, TV, or radio may generate noise.

• Do not expose the product to excessive dust

or vibration, or extreme cold or heat, in order

to prevent the possibility of panel

disfiguration, unstable operation, or damage

to the internal components.

• Do not install in locations where temperature

changes are severe. Otherwise,

condensation may form on the inside or the

surface of the product, causing it to break.

• If there is reason to believe that

condensation might have occurred, leave

the product for several hours without turning

on the power until the condensation has

completely dried out, in order to prevent

possible damage.

• Do not place vinyl, plastic or rubber objects

on the product, since this might cause

alteration or discoloration of the panel.

• When cleaning the product, use a dry and

soft cloth. Do not use paint thinners,

solvents, cleaning fluids, or chemical-

impregnated wiping cloths, since this might

cause alteration or discoloration.

PA_en_11 2/2

PRECAUTIONS

UR24C Startup Guide 7

Information

 About copyrights

• The software included in the TOOLS for

UR-C and the copyrights thereof are under

exclusive ownership by Yamaha

Corporation.

• This manual is the exclusive copyrights of

Yamaha Corporation.

• Copying of the software or reproduction of

this manual in whole or in part by any means

is expressly forbidden without the written

consent of the manufacturer.

• This product incorporates and bundles

computer programs and contents in which

Steinberg Media Technologies GmbH and

Yamaha Corporation own copyrights or with

respect to which it has license to use others’

copyrights. Such copyrighted materials

include, without limitation, all computer

software, style files, MIDI files, WAVE data,

musical scores and sound recordings. Any

unauthorized use of such programs and

contents outside of personal use is not

permitted under relevant laws. Any violation

of copyright has legal consequences.

DON’T MAKE, DISTRIBUTE OR USE

ILLEGAL COPIES.

 About functions/data bundled

with the product

• XLR-type connectors are wired as follows

(IEC60268 standard): pin 1: ground, pin 2:

hot (+), and pin 3: cold (-).

 About this manual

• The illustrations and screens as shown in

this manual are for instructional purposes

only.

• Steinberg Media Technologies GmbH and

Yamaha Corporation make no

representations or warranties with regard to

the use of the software and documentation

and cannot be held responsible for the

results of the use of this manual and the

software.

• Steinberg, Cubase and Cubasis are

registered trademarks of Steinberg Media

Technologies GmbH.

• Windows is a registered trademark of

Microsoft

Corporation in the United States

and other countries.

• Apple, Mac, iPad, iPadOS, iPhone, and

Lightning are trademarks of Apple Inc.,

registered in the U.S. and other countries.

• IOS is a trademark or registered trademark

of Cisco in the U.S. and other countries and

is used under license.

• The company names and product names in

this manual are the trademarks or registered

trademarks of their respective companies.

• Software may be revised and updated

without prior notice.

 About disposal

• This product contains recyclable

components. When disposing of this

product, please contact the appropriate

local authorities.

(bottom_en_01)

Yamaha/Steinberg cannot be held

responsible for damage caused by

improper use or modifications to the

product, or data that is lost or destroyed.

The model number, serial number, power

requirements, etc., may be found on or

near the name plate, which is at the

bottom of the unit. You should note this

serial number in the space provided

below and retain this manual as a

permanent record of your purchase to aid

identification in the event of theft.

Model No.

Serial No.

Manuals

8 UR24C Startup Guide

Manuals

The UR24C has the following two separate

manuals.

Startup Guide (this book)

Read this manual when setting up the

device. After finishing the setup as

indicated in this manual, read the Operation

Manual.

Operation Manual (PDF)

Read through this manual to understand

how to use the features of the product. You

can download the Operation Manual from

the Steinberg website:

http://www.steinberg.net/hardwaredownloads

NOTE

To view PDF files, you need to install Adobe

Reader on your computer. You can download

the latest version at the following website.

https://www.adobe.com/

Conventions in this

manual

Windows or Mac

When the procedures or explanations are

specific to only one of the platforms,

Windows or Mac, this is properly indicated

in the manual. When the platforms do not

appear, procedures or explanations are for

both Windows and Mac. This manual

predominantly uses screenshots of

Windows. However, Mac screenshots are

used when instructions of the function apply

only to the Mac.

Cubase series

The phrase “Cubase” in this manual applies

to all Cubase programs and versions

(except Cubase LE). If a specific version is

indicated, the version is described in the

text. This manual uses screenshots of

Cubase Pro 10 series. If you are using

another version of Cubase, the actual

screenshots might not be the same. For

details, refer to the Cubase manuals.

Cubasis series

This manual uses screenshots of Cubasis 2.

If you are using another version of Cubasis,

the actual screen shots might not be the

same.

Procedures

An arrow “” is shown for some

procedures in the manual. For example, the

string [Studio]  [Studio Setup]  [Control

Panel] indicates that you should perform the

procedures in the following order.

1. Click the [Studio] menu.

2. Select the [Studio Setup] option.

3. Click the [Control Panel] button.

Version information

The letters “x.x.x” and “x.xx” indicate the

version number.

TOOLS for UR-C

UR24C Startup Guide 9

TOOLS for UR-C

The software TOOLS for UR-C is necessary

for proper connection and use of the device

with a computer. Make sure to install it

before initially using the device (page 10).

You will need to download TOOLS for UR-C

beforehand from the Steinberg website

below.

http://www.steinberg.net/hardwaredownloads

When you install the TOOLS for UR-C, the

following three software programs will be

installed.

NOTE

• TOOLS for UR-C does not support an iOS/

iPadOS device.

• For the latest information on TOOLS for

UR-C, see the Steinberg website.

Yamaha Steinberg USB

Driver

This software allows communication

between the device and a computer.

Steinberg UR-C

Applications

This software allows setting the parameters

of the device from a computer or using the

Link function between the device and

Cubase series software. The software

consists of the following two components.

• Steinberg dspMixFx UR-C

This editing software lets you set the device

when using the device independently, or

when using it with a DAW (Digital Audio

Workstation) software other than Cubase

series. You can use Cubase and dspMixFx

UR-C at the same time.

• Steinberg UR-C Extension

This software allows you to link the device

with Cubase series (for versions which

supports the link function). To use this link

function, see the Steinberg web site below.

https://www.steinberg.net/

Basic FX Suite

Basic FX Suite is software consisting of

Plug-ins of various effects and sound

processing developed by Yamaha, some of

which fully utilize modeling technology.

When you install the Basic FX Suite, the

following three software programs will be

installed.

NOTE

AU (Audio Unit) Plug-ins are additionally

available, as well as VST Plug-ins, for use with

a Mac.

• Sweet Spot Morphing Channel

Strip

This processing effect is a multi effect that

features a compressor and equalizer.

•REV-X

This processing effect is a digital reverb

platform developed by Yamaha for

professional audio devices.

• Guitar Amp Classics

This processing effect features guitar amp

simulations developed by Yamaha that fully

utilize modeling technology.

Preparation before using with a computer

10 UR24C Startup Guide

Preparation before

using with a computer

The following three setup procedures are

required before you can use the device with

a computer.

• Installing TOOLS for UR-C

• Activating Basic FX Suite

• Downloading Cubase AI (DAW)

Installing TOOLS for UR-C

Download TOOLS for UR-C previously from

the Steinberg website. Follow the steps

below to install the TOOLS for UR-C.

NOTE

• You are only permitted to use this software

pursuant to the terms and conditions of the

“License Agreement” shown during the

installation.

• Future upgrades of application and system

software and any changes in specifications

and functions will be announced at the

following website.

https://www.steinberg.net/

• The eLicenser Control Center (eLCC) for

controlling the product license is installed at

the same time.

Windows

1. Disconnect all USB devices other

than the mouse and keyboard

from the computer.

2. Start the computer and log on to

the Administrator account.

Exit any open applications and close

all open windows.

3. Extract the previously downloaded

TOOLS for UR-C.

4. Double click the [setup.exe] file in

the extracted folder to start the

installation.

5. Follow the on-screen instructions

to install the software.

NOTE

• While installing the software, the “eLicenser

Control Center” installation message

appears. Follow the onscreen instructions to

install the software.

• You can select the desired software to be

installed on the installation screen.

- Yamaha Steinberg USB Driver

- Steinberg UR-C Applications

- Basic FX Suite (VST3 Plug-ins)

6. When installation has been

completed, click [Finish].

If a window requiring you to restart your

computer appears, follow the onscreen

instructions and restart the computer.

Confirmation of Installation

7. Move the [POWER SOURCE]

switch to the left and then connect

the device to a USB 3.0 jack on the

computer with the included USB

cable.

Make sure not to connect it to a USB

hub.

8. Open the [Device Manager]

window as follows.

[Control Panel]  ([Hardware and

Sound])  [Device Manager]

Preparation before using with a computer

UR24C Startup Guide 11

9. Click on the [>] mark next to

“Sound, video and game

controllers.”

10. Confirm that the device name is

listed.

Installation of the TOOLS for UR-C is now

complete.

Mac

1. Disconnect all USB devices other

than the mouse and keyboard

from the computer.

2. Start the computer and log in to

the Administrator account.

Exit any open applications and close

all open windows.

3. Extract the previously downloaded

TOOLS for UR-C.

4. Double click the [TOOLS for UR-C

V**.pkg] file in the extracted folder

to start the installation.

The characters ** represent the version

number.

5. Follow the on-screen instructions

to install the software.

NOTE

• While installing the software, the “eLicenser

Control Center” installation message

appears. Follow the onscreen instructions to

install the software.

• You can select the desired software to be

installed on the installation screen.

- Yamaha Steinberg USB Driver

- Steinberg UR-C Applications

- Basic FX Suite (VST3/AU Plug-ins)

6. When installation has been

completed, click [Restart] or

[Close].

Confirmation of Installation

7. Move the [POWER SOURCE]

switch to the left and then connect

the device to a USB 3.0 jack on the

computer with the included USB

cable.

Make sure not to connect it to a USB

hub.

8. Open the “Audio MIDI Setup”

window as follows.

[Applications]  [Utilities]  [Audio

MIDI Setup]

9. Confirm that the device name is

listed in the left column.

Installation of the TOOLS for UR-C is now

complete.

Preparation before using with a computer

12 UR24C Startup Guide

Activating Basic FX Suite

To use the Basic FX Suite programs which

are installed in “Installing TOOLS for UR-C,”

you will need to download the licenses for

them via the Internet. Use the Activation

Code provided on the ESSENTIAL

PRODUCT LICENSE INFORMATION.

1. Launch the “eLicenser Control

Center” as follows.

Windows

[All Programs] or [All apps] 

[eLicenser]  [eLicenser Control

Center]

Mac

[Applications]  [eLicenser Control

Center]

2. Click [Enter Activation Code].

3. Enter the Activation Code

described on the included

ESSENTIAL PRODUCT LICENSE

INFORMATION.

4. Follow the on-screen instructions

to download the licenses.

NOTE

If you connect a USB-eLicenser (USB

protection device) to your computer, a window

requiring you to select the destination of the

license appears. Follow the on-screen

instructions to select the device. Keep in mind

that the license saved in the USB-eLicenser

cannot be transferred to the Soft-eLicenser.

Downloading Cubase AI

We are offering Cubase AI as a free

download via our website, specifically for

customers who have purchased the

UR24C. Cubase AI is software for music

production that allows you to record, play,

and edit sounds on a computer. To

download the software, you’ll need to first

create a MySteinberg account on the

Steinberg website. For the latest

information, see the Steinberg website

below.

http://www.steinberg.net/getcubaseai/

NOTE

A valid “Download access code” is required

for Cubase AI download. It is printed on the

included CUBASE AI DOWNLOAD

INFORMATION.

The setup is now complete.

For detailed instructions and information on

the functions of the product, read the

operation manual.

Preparation before using with an iOS/iPadOS device

UR24C Startup Guide 13

Preparation before

using with an iOS/

iPadOS device

The following preparations are required

before you can use the device with an iOS/

iPadOS device.

Apple accessories

These may be necessary for connecting the

device to an iOS/iPadOS device.

• iOS/iPadOS device equipped

with Type-C port

USB-C charge cable in the Apple

product box.

• iOS/iPadOS device not

equipped with Type-C port

Lightning to USB Camera Adapter

(optional)

Lightning to USB 3 Camera Adapter

(optional)

Downloading Steinberg

dspMixFx UR-C (mixing app)

Download from the App store.

Downloading DAW app as

necessary

Download from the App Store.

NOTE

• Installing the TOOLS for UR-C is not

necessary when connecting the device to an

iOS/iPadOS device.

• For the latest information on compatible iOS/

iPadOS device, refer to the Steinberg

Website below.

https://www.steinberg.net/

The setup is now complete.

For detailed instructions and information on

the functions of the product, read the

operation manual. In the operation manual,

you can refer to the basic instructions for

operating with Cubasis (an iPad app sold

by Apple) as an example.

Setting up the power supply

14 UR24C Startup Guide

Setting up the power

supply

Connecting the USB cable

(bus-powered)

When using the device by bus power,

connect the included USB cable to the

USB 3.0 jack on a computer. When

connecting the device to a USB 3.1 Type-C

port, you will need a commercially available

USB 3.1 Type-C to Type-C cable (optional).

1. Move the [POWER SOURCE]

switch on the rear panel to the left.

2. Connect the included USB cable to

the [USB 3.0] jack on the rear

panel.

3. Connect the included USB cable to

the USB 3.0 jack on the computer.

4. The POWER indicator on the front

panel lights when the power is

turned on.

Connecting the USB power

adaptor or the USB mobile

battery

When connecting the device to a USB 2.0

jack on a computer or to iOS/iPadOS

device, you will need a commercially

available USB power adapter or USB

mobile battery for external power supply.

1. Move the [POWER SOURCE]

switch on the rear panel to the

right.

2. Insert the plug of the USB power

adaptor or USB mobile battery into

the DC IN [5V] port on the rear

panel.

3. The POWER indicator on the front

panel lights when the power is

turned on.

WARNING

Before turning the power of all

devices on or off, set all

volume levels to minimum.

Failing to do so may result in

hearing loss, electric shock, or

device damage.

(weee_eu_en_02)

(weee_eu_de_02)

(weee_eu_fr_02)

Information for users on collection and disposal of old equipment:

This symbol on the products, packaging, and/or accompanying documents means that used electrical

and electronic products should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection

points, in accordance with your national legislation.

By disposing of these products correctly, you will help to save valuable resources and prevent any

potential negative effects on human health and the environment which could otherwise arise from

inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local

municipality, your waste disposal service or the point of sale where you purchased the items.

For business users in the European Union:

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

Information on Disposal in other Countries outside the European Union:

This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or

dealer and ask for the correct method of disposal.

Verbraucherinformation zur Sammlung und Entsorgung alter Elektrogeräte

Befindet sich dieses Symbol auf den Produkten, der Verpackung und/oder beiliegenden Unterlagen, so

sollten benutzte elektrische Geräte nicht mit dem normalen Haushaltsabfall entsorgt werden.

In Übereinstimmung mit Ihren nationalen Bestimmungen bringen Sie alte Geräte bitte zur fachgerechten

Entsorgung, Wiederaufbereitung und Wiederverwendung zu den entsprechenden Sammelstellen.

Durch die fachgerechte Entsorgung der Elektrogeräte helfen Sie, wertvolle Ressourcen zu schützen, und

verhindern mögliche negative Auswirkungen auf die menschliche Gesundheit und die Umwelt, die

andernfalls durch unsachgerechte Müllentsorgung auftreten könnten.

Für weitere Informationen zum Sammeln und Wiederaufbereiten alter Elektrogeräte kontaktieren Sie bitte Ihre örtliche

Stadt- oder Gemeindeverwaltung, Ihren Abfallentsorgungsdienst oder die Verkaufsstelle der Artikel.

Information für geschäftliche Anwender in der Europäischen Union:

Wenn Sie Elektrogeräte ausrangieren möchten, kontaktieren Sie bitte Ihren Händler oder Zulieferer für weitere

Informationen.

Entsorgungsinformation für Länder außerhalb der Europäischen Union:

Dieses Symbol gilt nur innerhalb der Europäischen Union. Wenn Sie solche Artikel ausrangieren möchten, kontaktieren Sie

bitte Ihre örtlichen Behörden oder Ihren Händler und fragen Sie nach der sachgerechten Entsorgungsmethode.

Informations concernant la collecte et le traitement des déchets d’équipements électriques et

électroniques

Le symbole sur les produits, l'emballage et/ou les documents joints signifie que les produits électriques

ou électroniques usagés ne doivent pas être mélangés avec les déchets domestiques habituels.

Pour un traitement, une récupération et un recyclage appropriés des déchets d’équipements électriques

et électroniques, veuillez les déposer aux points de collecte prévus à cet effet, conformément à la

réglementation nationale.

En vous débarrassant correctement des déchets d’équipements électriques et électroniques, vous

contribuerez à la sauvegarde de précieuses ressources et à la prévention de potentiels effets négatifs sur

la santé humaine qui pourraient advenir lors d'un traitement inapproprié des déchets.

Pour plus d'informations à propos de la collecte et du recyclage des déchets d’équipements électriques et électroniques,

veuillez contacter votre municipalité, votre service de traitement des déchets ou le point de vente où vous avez acheté les

produits.

Pour les professionnels dans l'Union européenne :

Si vous souhaitez vous débarrasser des déchets d’équipements électriques et électroniques, veuillez contacter votre

vendeur ou fournisseur pour plus d'informations.

Informations sur la mise au rebut dans d'autres pays en dehors de l'Union européenne :

Ce symbole est seulement valable dans l'Union européenne. Si vous souhaitez vous débarrasser de déchets

d’équipements électriques et électroniques, veuillez contacter les autorités locales ou votre fournisseur et demander la

méthode de traitement appropriée.

(weee_eu_es_02)

(weee_eu_pt_02a)

(weee_eu_it_02)

Información para usuarios sobre la recogida y eliminación de los equipos antiguos

Este símbolo en los productos, embalajes y documentos anexos significa que los productos eléctricos y

electrónicos no deben mezclarse con los desperdicios domésticos normales.

Para el tratamiento, recuperación y reciclaje apropiados de los productos antiguos, llévelos a puntos de

reciclaje correspondientes, de acuerdo con la legislación nacional.

Al deshacerse de estos productos de forma correcta, ayudará a ahorrar recursos valiosos y a impedir los

posibles efectos desfavorables en la salud humana y en el entorno que de otro modo se producirían si se

trataran los desperdicios de modo inapropiado.

Para obtener más información acerca de la recogida y el reciclaje de los productos antiguos, póngase en contacto con

las autoridades locales, con el servicio de eliminación de basuras o con el punto de venta donde adquirió los artículos.

Para los usuarios empresariales de la Unión Europea:

Si desea desechar equipos eléctricos y electrónicos, póngase en contacto con su vendedor o proveedor para obtener

más información.

Información sobre la eliminación en otros países fuera de la Unión Europea:

Este símbolo solo es válido en la Unión Europea. Si desea desechar estos artículos, póngase en contacto con las

autoridades locales o con el vendedor y pregúnteles el método correcto.

Informações para os utilizadores relativas à recolha e eliminação de equipamentos usados

Este símbolo, presente em produtos, embalagens e/ou incluído na documentação associada, indica que

os produtos elétricos e eletrónicos usados não devem ser eliminados juntamente com os resíduos

domésticos em geral.

O procedimento correto consiste no tratamento, recuperação e reciclagem de produtos usados, pelo que

deve proceder à respetiva entrega nos pontos de recolha adequados, em conformidade com a

legislação nacional em vigor.

A eliminação destes produtos de forma adequada permite poupar recursos valiosos e evitar potenciais

efeitos prejudiciais para a saúde pública e para o ambiente, associados ao processamento incorreto dos

resíduos.

Para mais informações relativas à recolha e reciclagem de produtos usados, contacte as autoridades locais, o serviço de

eliminação de resíduos ou o ponto de venda onde foram adquiridos os itens relevantes.

Informações para utilizadores empresariais na União Europeia:

Para proceder à eliminação de equipamento elétrico e eletrónico, contacte o seu revendedor ou fornecedor para obter

informações adicionais.

Informações relativas à eliminação em países não pertencentes à União Europeia:

Este símbolo é válido exclusivamente na União Europeia. Caso pretenda eliminar este tipo de itens, contacte as

autoridades locais ou o seu revendedor e informe-se acerca do procedimento correto para proceder à respetiva

eliminação.

Informazioni per gli utenti sulla raccolta e lo smaltimento di vecchia attrezzatura

Questi simboli sui prodotti, sull'imballaggio e/o sui documenti che li accompagnano, indicano che i

prodotti elettrici ed elettronici non devono essere mischiati con i rifiuti generici.

Per il trattamento, il recupero e il riciclaggio appropriato di vecchi prodotti, si prega di portarli ai punti di

raccolta designati, in accordo con la legislazione locale.

Smaltendo correttamente questi prodotti si potranno recuperare risorse preziose, oltre a prevenire

potenziali effetti negativi sulla salute e l'ambiente che potrebbero sorgere a causa del trattamento

improprio dei rifiuti.

Per ulteriori informazioni sulla raccolta e il riciclaggio di vecchi prodotti, si prega di contattare l’amministrazione comunale

locale, il servizio di smaltimento dei rifiuti o il punto vendita dove sono stati acquistati gli articoli.

Per utenti imprenditori dell'Unione europea:

Se si desidera scartare attrezzatura elettrica ed elettronica, si prega di contattare il proprio rivenditore o il proprio fornitore

per ulteriori informazioni.

Informazioni sullo smaltimento negli altri Paesi al di fuori dell'Unione europea:

Questi simboli sono validi solamente nell'Unione Europea; se si desidera scartare questi articoli, si prega di contattare le

autorità locali o il rivenditore e richiedere informazioni sulla corretta modalità di smaltimento.

Важное примечание: Информация об условиях Гарантии для Клиентов в Российской Федерации

[Русский]

Для получения подробной информации об условиях Гарантии на продукцию Yamaha в России, условиях

гарантийного обслуживания, пожалуйста, посетите веб-сайт по адресу ниже (на сайте доступен файл с

условиями для скачивания и печати) или обратитесь в офис представительства Yamaha в России.

https://ru.yamaha.com/ru/support/

Продукция USB -аудиоинтерф ейс UR24C

Страна

происхождения

КИТАЙ

Изготовитель

YAMAHA CORPORATION 10-1 Nakazawa-cho,

Naka-ku, Hamamatsu-shi, Shizuoka-ken 430-8650, Япония.

Номинальное

напряжение

5 В пост. Тока

Потребляемая

мощность

4.5 Вт

Дата изготовления

Дата изготовления обозначена в серийном номере,

указанном на нижней или задней стороне инструмента.

Год изготовления обозначен первой из двух букв, предшествующих пяти последним

цифрам. 2020 год обозначен буквой «A», а следующие за ним годы обозначены

следующими за «A» буквами английского алфавита.

Месяц изготовления обозначен второй буквой, предшествующей пяти последним

цифрам. Месяцы с января по сентябрь обозначены буквами с «H» до «P», а

месяцы с октября по декабрь обозначены буквами от «X» до «Z».

Cooтветствует

требованиям

ТР ТС 004/2011

ТР ТС 020/2011

Срок хранения Срок хранения не установлен.

Условия для

утилизации

продуктов

Следуйте местному органу правил утилизации отходов.

Условия для

реализации

продуктов

Правила и условия реализации не установлены изготовителем и должны

соответствовать национальному и/или местному законодательству страны

реализации товара.

Название и адрес

импортера на

территории

таможенного союза

ООО "Ямаха Мюзик" г.Москва, улица Киевская, дом 7, офис 37

Условие хранения

Во избежание деформации и, повреждения внутренних компонентов

и сбоев в работе не держите оборудовани в помещениях с избыточной

вибрацией, а также в местах, где слишком пыльно, холодно или жарко.

Ser No. XXXAB00000

Месяц изготовленияГод изготовления

► Warranty Terms and Conditions

available as printed PDF file at

www.steinberg.net/warranty

The Warranty Terms and Conditions available as printed PDF file at www.steinberg.net/warranty

apply only for countries of the European Economic Area (EEA) and Switzerland.

► Gewährleistungsbestimmungen

finden Sie als druckbare PDF Datei unter

www.steinberg.de/warranty

Die Gewährleistungsbestimmungen in Schriftform sind als PDF-Datei unter www.steinberg.de/

warranty erhältlich und gelten nur für den Europäischen Wirtschaftsraum (EWR) und die Schweiz.

► Les conditions de garantie

se trouvent dans le document PDF imprimable sous

www.steinberg.net/warranty

Les conditions de garantie disponibles au format PDF à la page www.steinberg.net/warranty

s’appliquent uniquement aux pays de l’Espace économique européen (EEE) et à la Suisse.

► Las condiciones de garantía

se encuentran en el documento PDF en

www.steinberg.net/warranty

Los términos y condiciones de la garantía como archivo PDF para su impresión en

www.steinberg.net/warranty sólo están disponible en países del Espacio Económico Europeo

(EEE) y Suiza.

► Termos e condições de garantia

arquivo PDF disponível no endereço

www.steinberg.net/warranty

O arquivo PDF com os Termos e condições de garantia disponibilizado no endereço

www.steinberg.net/warranty aplica-se somente aos países da Área Econômica Europeia (AEE) e

à Suíça.

► Termini e Condizioni di Garanzia

disponibili su file PDF stampabile all’indirizzo web

www.steinberg.net/warranty

termini e le condizioni della garanzia, disponibili in formato PDF all’indirizzo www.steinberg.net/

warranty, sono validi soltanto per I paesi dell’Area Economica Europea (EEA) e per la Svizzera.

List of distributors

https://www.steinberg.net/en/company/distributor.html

If you need support or further product information please contact the distributor in your

country. A list of distributors is available at this website.

For assistance in determining who to contact, please contact “Headquarter SMTG.”

Wenn Sie Unterstützung oder weitere Produktinformationen benötigen, wenden Sie sich

bitte an den Vertrieb in Ihrem Land.

Eine Liste der Vertriebspartner finden Sie auf dieser Website.

Wenn Sie Hilfe benötigen, an wen Sie sich wenden sollten, kontaktieren Sie bitte

„Headquarter SMTG“.

Pour toute demande d’assistance ou d’information supplémentaire sur les produits, veuillez

contacter le distributeur agréé dans votre pays.

La liste des distributeurs agréés est disponible sur le site Web suivant.

Pour obtenir de l’aide sur les ressources à contacter, adressez-vous au « Siège de SMTG ».

Para solicitar asistencia o más información sobre el producto, póngase en contacto con el

distribuidor de su país.

Encontrará una lista de distribuidores en el siguiente sitio web.

Para consultas sobre el contacto adecuado, diríjase a “Headquarter SMTG.”

Se você precisar de suporte ou de mais informações sobre o produto, entre em contato

com o distribuidor no seu país.

Há uma lista de distribuidores disponível neste site.

Para receber ajuda para determinar com quem entrar em contato, fale com a “Sede da

SMTG”.

Per ottenere assistenza o avere ulteriori informazioni sul prodotto, contattare il distributore

locale.

L’elenco dei distributori e disponibile sul sito Web al seguente indirizzo.

Per individuare il distributore da contattare, rivolgersi alla sede centrale SMTG.

Если вам необходима техническая поддержка или дополнительные сведения о

продуктах, обратитесь к дистрибьютору в вашей стране.

Список дистрибьюторов можно найти на этом веб-сайте.

Чтобы узнать, к кому следует обращаться, свяжитесь с центральным офисом SMTG.

지원 또는 추가 제품 정보가 필요한 경우 해당 국가의 판매업체에 문의하십시오.

판매업체 목록은 다음 웹사이트에서 이용할 수 있습니다.

문의 판매업체를 결정하는 데 도움이 필요한 경우 "SMTG 본사"에 문의하십시오.

ENIT

HEAD OFFICE: Steinberg Media Technologies GmbH

Beim Strohhause 31, 20097 Hamburg, Germany Tel: +49-(0)40-210 35 0

La page charge ...

Steinberg UR24C Startup Manual

Marque: Steinberg

Modèle: UR24C

Catégorie: Équipement musical supplémentaire

Taper: Startup Manual

Télécharger le PDF

rapport

dans d''autres langues

English: Steinberg UR24C

Steinberg UR24C Startup Manual

Steinberg UR24C Startup Manual

dans d''autres langues

Documents connexes

Autres documents