Velp Scientifica JLT4 - JLT6 Manuel utilisateur

Marque
Velp Scientifica
Modèle
JLT4 - JLT6
Taper
Manuel utilisateur
1
Instruction Manual
Manuale di istruzioni
Manuel d’instructions
Manual de instrucciones
Bedienungsanleitung
指导手册
JLT4 - JLT6 Flocculators
F105A0108, F105A0109
General Information / Informazioni Generali / Informations Générales / Información General /
Allgemeine Hinweise / 一般信息
Before using the unit, please read the following instruction manual carefully.
Prima dell’utilizzo dello strumento si raccomanda di leggere attentamente il seguente manuale operativo.
Avant d’utiliser l’instrument, il est recommandé de lire attentivement le présent manuel d’instructions.
Antes de utilizar el instrumento, le recomendamos que lea con atención el siguiente manual de funcionamiento.
Bitte lesen Sie vor Inbetriebnahme des Geräts diese Bedienungsanleitung sorgfältig durch
在使用本装置之前，请仔细阅读以下使用说明书。
Do not dispose of this equipment as urban waste, in accordance with EEC directive 2002/96/CE.
Non smaltire l’apparecchiatura come rifiuto urbano, secondo quanto previsto dalla Direttiva 2002/96/CE.
Ne pas recycler l’appareil comme déchet solide urbain, conformément à la Directive 2002/96/CE.
No tirar el aparato en los desechos urbanos, como exige la Directiva 2002/96/CE.
Dieses Gerät unterliegt der Richtlinie 2002/96/EG und darf nicht mit dem normalen Hausmüll entsorgt werden.
根据 EEC 指令 2002/96/CE，请不要将本设备作为城市垃圾处理。
This unit must be used for laboratory applications only.
The manufacturer declines all responsibility for any use of the unit that does not comply with these instructions.
Questo strumento deve essere utilizzato solo per applicazioni di laboratorio.
La società produttrice declina ogni responsabilità sull’impiego non conforme alle istruzioni degli strumenti.
Cet instrument ne peut être utilisé que pour des applications de laboratoire.
Le fabriquant décline toute responsabilité en cas d’utilisation non conforme aux instructions concernant ces instruments.
Este dispositivo sólo debe utilizarse para aplicaciones de laboratorio.
El fabricante declina toda responsabilidad por el uso no conforme a las instrucciones de los dispositivos.
Dieses Gerät darf nur für Laboranwendungen verwendet werden.
Der Hersteller lehnt jede Haftung für unsachgemäße Verwendung oder Nichtbeachtung dieser Bedienungsanleitung ab.
本装置必须仅用于实验室应用。
制造商对任何不符合这些说明的使用不承担任何责任。
2
This unit has been designed and manufactured in compliance with the following standards:
Lo strumento è stato progettato e costruito in accordo con le seguenti norme:
L’instrument a été conçu et fabriqué conformément aux normes suivantes:
El dispositivo se ha sido diseñado y fabricado de acuerdo con las siguientes normas:
Das Gerät wurde in Übereinstimmung mit folgenden Normen entwickelt und gebaut:
本装置的设计和制造符合以下标准。
Safety requirements for electrical equipment for measurement, control and for laboratory use
Prescrizioni di sicurezza per apparecchi elettrici di misura, controllo e per l’utilizzo in laboratorio
Règles de sécurité pour appareils électriques de mesurage, de régulation et de laboratoire
Prescripciones de seguridad para equipos eléctricos de medición, control y su uso en laboratorio
Sicherheitsbestimmungen für elektrische Mess-, Steuer-, Regel- und Laborgeräte
测量、控制和实验室用电气设备的安全要求
IEC/EN 61010-1
Electrical equipment for laboratory use
UL 61010-1
General requirement - Canadian electrical code
CAN/CSA-C22.2 No.61010-1
VELP reserves the right to modify the characteristics of its products with the aim to constantly improving their quality.
Nell’impegno di migliorare costantemente la qualità dei prodotti, VELP si riserva la facoltà di variarne le caratteristiche.
Dans le but d’améliorer constamment la qualité de ses produits, VELP se réserve le droit d’apporter des modifications aux
caractéristiques de ceux-ci.
VELP se reserva el derecho de modificar las características de sus productos con el objetivo de mejorar constantemente su
calidad.
VELP behält sich zum Zwecke der ständigen Verbesserung der Produktqualität das Recht auf Änderung der
Geräteeigenschaften vor.
VELP 保留修改其产品特性的权利，目的是不断提高其质量。
3
4
Analytical methods
Coagulation and flocculation of wastewaters
Chemical coagulants are added to wastewaters for the primary purpose of removing suspended solids and also phosphorus.
The addition of chemicals reduces also heavy metal concentrations and improves disinfection efficiency. Chemical
coagulation can be obtained by adding to wastewaters defined amounts of lime (calcium hydroxide), alum (aluminium
sulphate) or iron salts (ferric or ferrous). The coagulation-sedimentation process typically involves:
a) injection and mixing of the coagulant that neutralize the electric charge, prevalently negative, on suspended particles.
Good and rapid mixing of the coagulant and wastewater is important to ensure efficient use of the chemical. Typical
detention times in plant basins for turbulent mixing are 15 to 120 seconds.
b) agglomeration of the coagulated particles into large settable flocs. This agglomeration is accomplished by stirring the
water slowly so to allow the solids formed by the addition of chemicals to grow in size so that they can be removed by
gravity settling. The stirring is usually performed by slowly rotating paddles during 10 to 30 minutes.
c) sedimentation of the flocculated material by gravity separation. The solids are allowed to settle by gravity from the
chemically treated standing wastewater. The effluent from the chemical settling tank is very clear and does not usually
require further filtration.
The quantity of chemical coagulant required to achieve the test varies with time and from wastewater to wastewater.
Typical coagulant doses are: 75 to 250 g/m3 for alum , 45 to 90 g/m3 for ferric chloride, 200 to 400 g/m3 for lime.
Reagents
The choice and dosing of the chemical coagulant to be adopted for the removal of suspended solids from wastewaters
derive from the results of laboratory evaluations by the so-called Jar test. Multiple stirrers with reproducible stirring speeds
allow to adopt standard conditions for the test, that are the basic requirement for reproducible results.
The standard conditions are related to:
- dimensions and shape of vessel and stirring paddle - volume of wastewater
- time and speed of stirring during turbulent mixing - time and speed of stirring during flocculation
- evaluation criteria for the obtained results.
The most diffused adopted conditions are:
- 1000 ml glass beakers (jars), tall form, Ø 105 mm - 600 ml wastewater samples
- stirring paddles 25 mm high, 75 mm wide, 1 mm thickness - stirring height of paddles, middle height of sample
- turbulent stirring after chemical addition: 120 rpm, 120 seconds - slow speed flocculation: 30 rpm, 25 minutes
- first evaluation of results after 5 minutes of sedimentation
The results can be evaluated on the basis of different criteria:
a) floc dimension evaluation with numerical degree (0=no flocs, 2=very small, 4=small, 6=medium, 8=large, 10=very large).
b) time from the addition of chemicals to first appearing of flocs.
c) evaluation of residual turbidity of supernatant, after a determined sedimentation time, by turbidimeter.
d) measurement of electro-kinetic potential of suspended particles on a sample taken immediately after the addition and
mixing of chemicals. Coagulations should be easier when zeta potential of particles is very low.
e) evaluation of filterability of clarified water by standardized membrane filters under pressure. The reduction of water flow
with time is related to the degree of clogging of filters due to residual unsettled suspended matter.
Other measurements are related to the pH of water after chemical treatment (lime raises the value while iron and aluminium
salts lower it) and the temperature of water at which the experiments are performed.
References: American Society for Testing Materials Norm ASTM D-2035-G4 T; Passino R. and M.Beccari (1970)
“Standardization of jar test in coagulation-flocculation processes for the removal of inorganic turbidities (in Italian). Acqua e
Aria, Milano, 1-10, October 1970”; Degremont (1978) “Etude de la coagulation et de la floculation des eaux. Methode n.703,
948-950. Memento technique de l'eau. 1200 pages, Paris”; U.S. Association of Environmental Engineering Professors
(1972) “Environmental Engineering Unit Operations and Unit Processes Laboratory Manual. J.T. O'Connor Ed. 350 ppg”.
Leaching test
Leaching tests are used to simulate the behaviour of a waste in a dump that is submitted to the leaching activity of rain
water. There are two different methods that use leaching solutions of different type:
a) acetic acid, proposed for dumps receiving both organic and inorganic wastes;
b) carbon dioxide saturated water, for dumps receiving only inorganic wastes.
Waste sample to be examined: if a liquid phase is present, it must be removed by filtration or centrifugation and preserved
in a refrigerator at 2-4 °C. The granulometry of the solid phase, must be lower than 9.5 mm (standard sieve).
Waste extraction: 20-25 g of the solid phase are weighed with a precision of ± 0.1 g.
Method a) A volume of distilled water corresponding to 16 times the weight of the sample is added.
The pH of the mixture is kept to 5±0.2 using 0.5 N acetic acid. The stirring is performed for 24 hours, controlling the pH
every 15 minutes during the first hour and then every hour. The pH is corrected to 5±2 using again 0.5 N acetic acid. If after
24 hours of stirring the pH is higher than 5.2, a new correction is made and the stirring prolonged for other 4 hours.
Method b) The leaching solution is given by a volume corresponding to 20 times the sample weight of distilled water
saturated by carbon dioxide for not less than 15 minutes. The stirring is performed during 6 hours without any pH correction.
Stirring speed: must be able to maintain continuously mixed the solid phase with the leaching solution.
Analysis of extract: the leaching solution and the liquid phase if present in the original sample are filtered by a membrane
filter of 0.45 µm porosity and submitted to analysis for the single metals by the methods commonly used for waters.
5
Contents / Indice / Index / Índice / Inhalt / 内容
ANALYTICAL METHODS ......................................................................................................................................................... 4
1. INTRODUCTION .............................................................................................................................................................. 6
2. ASSEMBLY AND INSTALLATION ................................................................................................................................... 6
2.1 ELECTRICAL CONNECTION .................................................................................................................................................................... 6
2.2 START-UP ........................................................................................................................................................................................ 6
3. OPERATING CONTROLS ............................................................................................................................................... 6
4. MAINTENANCE ............................................................................................................................................................... 6
4.1 CLEANING ........................................................................................................................................................................................ 6
5. TECHNICAL DATA .......................................................................................................................................................... 6
6. ACCESSORIES / SPARE PARTS ................................................................................................................................... 6
1. INTRODUZIONE .............................................................................................................................................................. 7
2. MONTAGGIO ED INSTALLAZIONE ................................................................................................................................ 7
2.1 COLLEGAMENTO ALLA RETE ELETTRICA .................................................................................................................................... 7
2.2 AVVIO........................................................................................................................................................................................... 7
3. CONTROLLI DI FUNZIONAMENTO ................................................................................................................................ 7
4. MANUTENZIONE ............................................................................................................................................................. 7
4.1 PULIZIA ........................................................................................................................................................................................ 7
5. CARATTERISTICHE TECNICHE .................................................................................................................................... 7
6. ACCESSORI / PARTI DI RICAMBIO ............................................................................................................................... 7
1. INTRODUCTION .............................................................................................................................................................. 8
2. MONTAGE ET INSTALLATION ....................................................................................................................................... 8
2.1 RACCORDEMENT AU RESEAU ELECTRIQUE ............................................................................................................................................... 8
2.2 MISE EN MARCHE .............................................................................................................................................................................. 8
3. CONTRÔLES DES OPÉRATIONS .................................................................................................................................. 8
4. ENTRETIEN ..................................................................................................................................................................... 8
4.1 NETTOYAGE ..................................................................................................................................................................................... 8
5. CARACTÉRISTIQUES TECHNIQUES ............................................................................................................................ 8
6. ACCESSOIRES / PIECES DE RECHANGE.................................................................................................................... 8
1. INTRODUCCIÓN ............................................................................................................................................................. 9
2. MONTAJE E INSTALACIÓN ............................................................................................................................................ 9
2.1 CONEXIÓN A RED ELÉCTRICA ................................................................................................................................................................ 9
2.2 ENCENDIDO ...................................................................................................................................................................................... 9
3. CONTROLES DE FUNCIONAMIENTO ........................................................................................................................... 9
4. MANTENIMIENTO ........................................................................................................................................................... 9
4.1 LIMPIEZA ......................................................................................................................................................................................... 9
5. CARACTERÍSTICAS TÉCNICAS .................................................................................................................................... 9
6. ACCESORIOS / REFACCIONES .................................................................................................................................... 9
1. EINFÜHRUNG ............................................................................................................................................................... 10
2. MONTAGE UND INSTALLATION .................................................................................................................................. 10
2.1 ANSCHLUSS AN DAS STROMNETZ ........................................................................................................................................................ 10
2.2 INBETRIEBNAHME ............................................................................................................................................................................ 10
3. BEDIENUNGSELEMENTE ............................................................................................................................................ 10
4. WARTUNG ..................................................................................................................................................................... 10
4.1 REINIGUNG .................................................................................................................................................................................... 10
5. TECHNISCHE MERKMALE ........................................................................................................................................... 10
6. ZUBEHÖR / ERSATZTEILE .......................................................................................................................................... 10
1. 简介 ................................................................................................................................................................................ 11
2. 装配和安装 ..................................................................................................................................................................... 11
2.1 电气连接 .................................................................................................................................................................................... 11
2.2 初创 ............................................................................................................................................................................................ 11
3. 操作控制 ......................................................................................................................................................................... 11
4. 维护 ................................................................................................................................................................................ 11
4.1 清洗 ............................................................................................................................................................................................ 11
5. 技术数据 ......................................................................................................................................................................... 11
6. 附件 / 备件 ...................................................................................................................................................................... 12
7. WIRING DIAGRAM / SCHEMA ELETTRICO / SCHEMA ELECTRIQUE / ESQUEMA ELÉCTRICO / SCHALTPLAN 13
8. DECLARATION OF CONFORMITY / DICHIARAZIONE DI CONFORMITA / DECLARATION DE CONFORMITE /
DECLARACIÓN DE CONFORMIDAD / KONFORMITÄTSERKLÄRUNG / 符合性声明 ...................................... 14
9. DECLARATION OF CONFORMITY ........................................................................................................................ 15
6
1. Introduction
During chemical-physical treatments of waters aimed to coagulate and precipitate pollutants, chemical coagulants are
evaluated and their dosing optimized by jar tests. In relation to the variable composition of wastewaters the chemical dosing
and the test frequency are to be adapted to local conditions. JLT Series is characterized by a settable speed of rotation,
from 10 to 300 rpm, with the real speed showed on the relative display. The steel structure epoxy painted is studied and
tested in order to give the instrument an excellent resistance against the attack of chemical agents and corrosion in general.
The stainless-steel stirring rods are adjustable in height by a self-blocking chuck. The examined samples can be lighted by a
back fluorescent lamp controlled by a switch located on front panel.
2. Assembly and installation
Upon receipt and after having removed the packaging, please check the integrity of the instrument. The box includes:
• Flocculator
• Plug for power supply • Switching VELP 100-240V/12V without plug
• Instruction manual
2.1 Electrical connection
Before connecting the instrument to the power supply, make sure that the values on the rating plate correspond to those of
the power supply. Connect the unit to the power supply using the transformer supplied.
Ensure that the socket and the relative cut-off device conform to current safety norms and easy to reach.
2.2 Start-up
Place the beakers containing the sample and then, set the speed and time using + or -.
3. Operating controls
The start-up is empowered by the keys + and -. t’s possible to select the speed from 10 to 300 rpm. The progression speed
is increased by keeping one of the two keys pushed, in order to reach the desired value faster.
It’s possible to select two different type of running by the SET key on the “Electronic Timer Windows”:
- Continuous (. . .); - With timer (minute/hour base);
In order to change the timer modality (minutes/hour base), maintain the set key pushed for a few seconds:
- With timer (minutes): “000” - with timer (hours): “h00”
If the time of running is not selected, the stirring is not active.
The display shows the count down and simultaneously the third decimal point turns on to indicate that the count is operative.
At the end, the instrument stops the stirring, the acoustic signal warns the end of the time and the display shows “End”.
4. Maintenance
No routine or extraordinary maintenance is necessary apart from periodically cleaning the unit as described in this manual.
In compliance with the product guarantee law, repairs to our units must be carried out in our factory, unless previously
agreed otherwise with local distributors. The instrument must be transported in its original packaging and any indications
present on the original packaging must be followed (e.g., palletized). It is the responsibility of the user, to properly
decontaminate the unit in case of hazardous substances remaining on the surface or interior of the device. If in doubt about
the compatibility of a cleaning or decontamination product, contact the manufacturer or distributor.
4.1 Cleaning
Disconnect the unit from the power supply and use a cloth dampened with an non-inflammable non-aggressive detergent.
5. Technical data
Power supply
100-240 V / 50-60 Hz
Power
19 W
Dimensions (WxHxD)
655x404x296 mm (JLT4) 935x404x296 mm (JLT6)
Weight (with plug)
13.0 Kg (JLT4) 17.0 Kg (JLT6)
Speed range
10 ÷ 300 rpm, 1 rpm step
Time range
0 ÷ 999 minutes / 0 ÷ 99 hours or continuous
Construction material
Epoxy painted metal structure
Environmental ambient temperature
5 - 40 °C (41 - 104°F)
Storage temperature range
-10… + 60 °C (14 - 140°F)
Max humidity
80%
Pollution degree
2
6. Accessories / Spare parts
A00001000 Plastic Becher 1000 ml A00001001 Glass Becher 1000 ml
A00001002 Transparent plastic Imhoff cone A00001003 Glass graduated Imhoff cone
A00001004 Stand for 2 Imhoff cones 10000235 Foot
EN
7
1. Introduzione
Nei trattamenti chimico-fisici delle acque idonei alla coagulazione e precipitazione degli inquinanti, le sostanze chimiche per
precipitazione vengono confrontate per la loro efficacia ed i loro dosaggi ottimizzati per mezzo di prove Jar Test.
Date le caratteristiche variabili dei liquami, i dosaggi chimici e la frequenza del test devono essere adattati alle condizioni
locali. VELP ha realizzato questo apparecchio per l’esecuzione di Jar Test caratterizzato dalla velocità di rotazione
impostabile, in un range da 10 a 300 rpm, con visualizzazione della velocità reale a display.
2. Montaggio ed installazione
Verificare l’integrità dello strumento al ricevimento. Gli elementi contenuti nell’imballo sono i seguenti:
• Flocculatore
• Manuale di istruzioni • Cavo di alimentazione 100-240V/12V
• Spina UE
2.1 Collegamento alla rete elettrica
Prima di collegare l’unità alla rete di alimentazione elettrica, assicurarsi che i dati di targa dell’unità corrispondano a quelli
disponibili. Assicurarsi che sia la presa di corrente che il relativo dispositivo di sezionamento siano conformi alle norme di
sicurezza e di facile accessibilità.
2.2 Avvio
Collocare il contenitore con il liquido e regolare la velocità di agitazione ed il tempo desiderato con i tasti + o -.
3. Controlli di funzionamento
Tramite i tasti + o - della finestra “Speed rpm” si può selezionare la velocità di agitazione da 10 a 300 rpm. Mantenendo
premuto uno dei due tasti, la velocità di progressione aumenta al fine di ottenere più rapidamente la velocità desiderata.
Si possono selezionare 2 tipi diversi di funzionamento tramite il tasto Set della finestra “Time”:
• Continuo (…) • Temporizzato (minuti/ore).
Per cambiare la base tempo mantenere premuto il tasto Set per qualche secondo.:
• funzionamento temporizzato (minuti): “000” • funzionamento temporizzato (ore): “h00”
L’impostazione del tempo desiderato si effettua mediante i pulsanti + e -. L’agitazione non è attiva se è stato programmato
un funzionamento temporizzato ed il tempo residuo è 0. Il display visualizza costantemente il tempo residuo a scalare e
contemporaneamente il terzo punto decimale si accende in modalità intermittente stando ad indicare che il conteggio è
operativo. Allo scadere del tempo programmato l’agitazione si ferma automaticamente, una segnalazione acustica si attiva e
il display visualizza in modo intermittente “end”.
4. Manutenzione
La manutenzione ordinaria e straordinaria non è prevista salvo la pulizia periodica dello strumento come descritto in questo
manuale. In conformità alla legge sulla garanzia dei prodotti, le riparazioni dei nostri strumenti devono essere eseguite
presso la nostra sede, salvo accordi diversi con i distributori locali. Il trasporto dello strumento tramite spedizionieri, corrieri o
altro, deve essere effettuato utilizzando l'imballo originale antiurto di cui lo strumento è dotato quando spedito da nuovo.
Seguire le istruzioni eventualmente riportate sullo stesso (es. pallettizzare). È responsabilità dell'utente procedere alla
decontaminazione dell'unità nel caso in cui sostanze pericolose rimangano sulla superficie o all'interno del dispositivo. In
caso di dubbi sulla compatibilità di un prodotto per la pulizia o la decontaminazione, contattare il produttore o il distributore.
4.1 Pulizia
La pulizia dello strumento deve essere eseguita, dopo aver staccato l’alimentazione, con un panno inumidito con detergenti
non infiammabili e non aggressivi.
5. Caratteristiche tecniche
100-240 V / 50-60 Hz
19 W
655x404x296 mm (JLT4) 935x404x296 mm (JLT6)
13.0 Kg (JLT4) 17.0 Kg (JLT6)
10 ÷ 300 rpm, step da 1 rpm
0 ÷ 999 minuti / 0 ÷ 99 ore o in continuo
Metallica con verniciatura epossidica
5 - 40 °C (41 - 104°F)
-10… + 60 °C (14 - 140°F)
80%
2
6. Accessori / Parti di ricambio
A00001000 Becher 1000 ml in plastica A00001001 Becher 1000 ml in vetro
A00001002 Cono Imhoff in plastica A00001003 Cono Imhoff in vetro
A00001004 Supporto per coni Imhoff a due posti 10000235 Piedino
IT
8
1. Introduction
Floculateurs pour exécuter Jar Test caractérisé donne un contrôle électronique de la vitesse commun pour toutes les
positions. La vitesse de rotation programmable de 10 à 300 t/min (par pas de 1 t/min) et est affiché sur l'écran.
2. Montage et installation
Lors de la réception et après avoir enlevé l’emballage, contrôler que l’instrument est intègre La fourniture comprend:
• Floculateur
• Fiche UE pour alimentateur • Câble d'alimentation100-240V/12V
• Manuel d’instructions
2.1 Raccordement au réseau électrique
Avant de brancher l’instrument au réseau d’alimentation électrique, vérifier que les données de la plaque de l’instrument
correspondent aux données disponibles à la prise d’alimentation.
2.2 Mise en marche
Disposez le réservoir avec le liquide et régler la vitesse d’agitation et la durée d'utilisation avec + et -.
3. Contrôles des opérations
La vitesse d'agitation de 10 à 300 t/min, par pas de 1 t/min, est sélectionnée en appuyant sur les touches + et - de l'écran
de "Vitesse Il est possible de sélectionner deux types de fonctionnement différents à l'aide de la touche SET sur les
"Fenêtres de la minuterie électronique" :
- Continu (. . .) ; - Avec minuterie (base minutes/heures) ;
Pour changer la modalité du timer (base minutes/heures), maintenez la touche SET enfoncée pendant quelques secondes :
- Avec minuterie (minutes) : "000" - avec minuterie (heures) : "h00"
Si le temps de fonctionnement n'est pas sélectionné, l'agitation n'est pas active.
L'écran affiche en continu le temps restant et le troisième point décimal scintille en même temps pour indiquer que le
décompte est en cours. A la fin du temps programmé, l'agitation s'arrête automatiquement et un signal sonore avertit
l'utilisateur que la procédure est terminée. L'écran affiche "end" (fin).
4. Entretien
Aucun entretien ordinaire ou extraordinaire n’est prévu excepté le nettoyage périodique de l’instrument comme décrit dans
le présent manuel. Conformément à la loi sur la garantie des produits, les réparations de nos instruments doivent être
effectuées dans nos ateliers, sauf accords différents avec les distributeurs locaux. L'instrument doit être transporté dans son
emballage d'origine et les indications présentes sur l'emballage d'origine doivent être suivies (par exemple palettisér).
Il est de la responsabilité de l'utilisateur de décontaminer correctement l'unité en cas de substances dangereuses restant
sur la surface ou à l'intérieur de l'appareil. En cas de doute sur la compatibilité d'un produit de nettoyage ou de
décontamination, contactez le fabricant ou le distributeur.
4.1 Nettoyage
Le nettoyage de l’instrument doit être effectué après avoir débranché l’appareil, à l’aide un chiffon légèrement imbibé de
détergent non inflammable et non agressif.
5. Caractéristiques techniques
Prise d'alimentation
100-240 V / 50-60 Hz
Puissance
19 W
Dimensions (LxHxP)
655x404x296 mm (JLT4) 935x404x296 mm (JLT6)
Poids
13.0 Kg (JLT4) 17.0 Kg (JLT6)
Ecart de réglage vitesse
10 ÷ 300 rpm, 1 rpm étape
Temps de travail
0 à 999 minutes / 0 à 99 heures ou en continu
Châssis
Epoxy métal
Température admise - Milieu environnant
5 - 40 °C (41 - 104°F)
Température admise - Stockage
-10… + 60 °C (14 - 140°F)
Humidité admise
80%
Degré de pollution
2
6. Accessoires / Pièces de rechange
A00001000 Bécher en plastique 1000 ml A00001001 Bécher en verre, 1000 ml
A00001002 Imhoff Cône plastique A00001003 Imhoff Cône verre
A00001004 Soutien aux cônes Imhoff en deux endroits 10000235 Pied
FR
9
1. Introducción
Floculadores para la ejecución de Jar Test caracterizado da el control electrónico de velocidad con ajuste común para todas
las posiciones. La serie JLT se caracteriza por una velocidad de rotación ajustable, de 10 a 300 rpm, con la velocidad real
mostrada en la pantalla.
2. Montaje e instalación
Al recibir el producto, quitar el embalaje y comprobar la integridad del aparato. El suministro incluye:
• Floculador
• Clavija UE para alimentador • Alimentador 100-240V/12V sin clavija
• Manual de instrucciones
2.1 Conexión a red eléctrica
Asegúrarse que las características de la placa corresponden y que la toma de corriente cumplia con las normas de
seguridad y accesibilidad.
2.2 Encendido
Colocar un recipiente para contener la muestra y ajustar la velocidad y el tiempo de funcionamiento con + y -.
3. Controles de funcionamiento
El inicio de la agitación se lleva a cabo mediante + y - ("Speed rpm"). Se puede seleccionar la velocidad deseada de 10 a
300 rpm. Es posible seleccionar dos tipos diferentes de funcionamiento mediante la tecla SET en las "Ventanas del
Temporizador Electrónico":
- Continua (. . .); - Con temporizador (base de minutos/hora);
Para cambiar la modalidad del temporizador (base minutos/hora), mantenga pulsada la tecla set durante unos segundos:
- Con temporizador (minutos): "000" - Con temporizador (horas): "h00"
Si no se selecciona el tiempo de funcionamiento, la agitación no está activa. La agitación no está activa si se ha
programado una operación programada y el tiempo restante es 0. La pantalla muestra constantemente el tiempo, y al
mismo tiempo el terceros punto decimal se ilumina de forma intermitente indicando que la cuenta del tiempo está activa. A
la fin del tiempo programado, la agitación se detiene automáticamente, una señal acústica se activa y la pantalla muestra
"end".
4. Mantenimiento
El mantenimiento ordinario y extraordinario no está previsto excepto para la limpieza periódica del aparato como se
describe en este manual. De acuerdo con la ley de garantía del producto, las reparaciones de nuestros aparatos se deben
llevar a cabo en nuestras instalaciones, a menos que se acuerde otra cosa con los distribuidores locales.
El equipo debe transportarse sólo en su embalaje original y todas las indicaciones presentes en el embalaje original debe
seguirse (por ejemplo, paletizado). Es responsabilidad del usuario descontaminar la unidad en el caso de que haya restos
de sustancias peligrosas tanto en la superficie como en el interior del equipo. En caso de duda sobre la compatibilidad de
los productos a usar para limpieza y/o descontaminacion, contacte con su distribuidor o con fabricante.
4.1 Limpieza
La limpieza del aparato debe llevarse a cabo, después de desconectar la alimentación, con un paño húmedo con
detergentes no inflamables y no agresivos.
5. Características técnicas
Fuente de alimentación externa
100-240 V / 50-60 Hz
Potencia
19 W
Dimensiones (LxHxP)
655x404x296 mm (JLT4) 935x404x296 mm (JLT6)
Peso
13.0 Kg (JLT4) 17.0 Kg (JLT6)
Ámbito de ajuste velocidad
10 ÷ 300 rpm, 1 rpm
Tiempo de trabajo
0 a 999 minutos / 0 a 99 horas o en continuo
Estructura
Metálica recubierta con pintura epoxi
Temperatura admitida - Almacenamiento
5 - 40 °C (41 - 104°F)
Temperatura admitida - Ambiente
-10… + 60 °C (14 - 140°F)
Humedad admitida
80%
Grado de contaminación
2
6. Accesorios / Refacciones
A00001000 Vaso de plástica de 1000 ml A00001001 Vaso de vidrio de 1000 ml
A00001002 Cono Imhoff plástico A00001003 Cono Imhoff vidrio
A00001004 Soporte para conos Imhoff en dos lugares 10000235 Pie
ES
10
1. Einführung
JLT Serie bietet elektronische Drehzahlregelung und Einstellung der Drehzahl gemeinsam für alle Positionen . JLT wird
durch eine einstellbare Drehzahl gekennzeichnet, von 10 bis 300 rpm, mit der realen Geschwindigkeit zeigte auf der
relativen Darstellung.
2. Montage und Installation
Bitte überprüfen Sie nach dem Auspacken den einwandfreien Zustand des Gerätes. Im Lieferumfang sind enthalten:
• Flockulator
• EU-Stecker für Netzteil • Netzteil 100-240V/12V ohne Stecker
• Bedienungsanleitung
2.1 Anschluss an das Stromnetz
Prüfen Sie bitte vor dem Anschluß an das Stromnetz, dass der Netzschalter ausgeschaltet ist und der Drehknopf auf
Linksanschlag steht. Dann können Sie das Gerät mit der Anschlußleitung an das Stromnetz anschließen.
2.2 Inbetriebnahme
Für Start und Steuerung der Schüttelbewegung bedienen Sie sich der Pfeilen + und -.
3. Bedienungselemente
Um die Bewegung zu starten, drücken Sie die Tasten + und - auf dem Bedienfeld "Speed rpm". Es ist möglich, die
gewünschte Geschwindigkeit von 10 bis 300 rpm wählen. Es ist möglich, mit der SET-Taste im "Elektronischen
Zeitschaltuhr-Fenster" zwei verschiedene Lauftypen auszuwählen:
- Kontinuierlich (. . .); - Mit Timer (Minuten-/Stundenbasis);
Um die Timer-Modalität (Minuten-/Stundenbasis) zu ändern, halten Sie die Set-Taste für einige Sekunden gedrückt:
- Mit Timer (Minuten): "000" - mit Timer (Stunden): "h00"
Wenn die Laufzeit nicht ausgewählt ist, ist das Rühren nicht aktiv.
Das Rühren ist nicht aktiv, wenn Sie einen zeitgesteuerten Betrieb programmiert haben und die verbleibende Zeit 0 ist.
Das Display zeigt ständig die verbleibende Zeit, während die dritte Dezimalstelle leuchtet in der intermittierende Form.
Am Ende der programmierten Zeit stoppt das Rühren automatisch, ein akustisches Signal aktiviert ist und auf dem Display
erscheint intermittierend "End".
4. Wartung
Abgesehen von einer regelmäßigen Reinigung gemäß der nachfolgenden Hinweise benötigt das Gerät keine gewöhnliche
oder außergewöhnliche Wartung. In Übereinstimmung mit dem Produkthaftungsgesetz müssen Reparatureingriffe an den
Geräten in unserem Hause durchgeführt werden, soweit keine anderweitigen Vereinbarungen mit den örtlichen Händlern
getroffen werden. Das Gerät muss in der Originalverpackung transportiert werden. Es liegt in der Verantwortung des
Benutzers, das Gerät ordnungsgemäß zu dekontaminieren, falls gefährliche Substanzen auf der Oberfläche oder im Inneren
des Geräts verbleiben. Wenn Sie Zweifel an der Verträglichkeit eines Reinigungs- oder Dekontaminationsprodukts haben,
wenden Sie sich an den Hersteller oder Händler.
4.1 Reinigung
Trennen Sie das Gerät zur Reinigung vom Stromnetz und verwenden Sie ein weiches Tuch mit einem sanften, nicht
entzündlichen Reiniger.
5. Technische merkmale
100-240 V / 50-60 Hz
19 W
655x404x296 mm (JLT4) 935x404x296 mm (JLT6)
13.0 Kg (JLT4) 17.0 Kg (JLT6)
10 ÷ 300 rpm, 1 rpm étape
von 0 bis 999 Minuten / von 0 bis 99 Stunden oder Dauerbetrieb
Epoxy lackiertem Metall
5 - 40 °C (41 - 104°F)
-10… + 60 °C (14 - 140°F)
80%
2
6. Zubehör / Ersatzteile
A00001000 Kunststoffbecher, 1000 ml A00001001 Glasbecher, 1000 ml
A00001002 Imhoff Cone Kunststoff A00001003 Imhoff Cone Glas
A00001004 Unterstützung für Imhoff Kegel mit zwei Orten 10000235 Fuß
DE
11
1. 简介
在对凝固和沉淀污染物的水域进行化学物理处理期间，对化学凝结剂进行评估，并通过罐体测试优化其剂型。关于废水的可
变成分，化学剂和测试频率应因地制宜。JLT系列的特点是可设定的旋转速度，从10到300rpm，相关显示屏上显示真实速度。
对涂漆的钢结构环氧树脂进行研究和测试，使仪器具有极好的抗化学制剂和腐蚀能力。不锈钢搅拌棒的高度可通过自挡夹头
调节。被检查的样品可以通过前面板上的开关控制的后荧光灯照亮。
2. 装配和安装
收到包装后和拆下包装后，请检查仪器的完整性。 包括：
• 絮凝器
• 电源插头
• 开关 VELP 100-240V/12V，无插头
• 使用说明书
2.1 电路连接
在将仪表连接到电源之前，请确保额定板上的值与电源值相对应。使用所提供的变压器将设备连接到电源。
确保插座和相对切断装置符合当前安全规范，且易于触及。
2.2 开机
放置包含样品的烧杯，然后使用+或-设置速度和时间。
3. 操作控制
启动是由键+和-开启的。可以选择转速从 10 到300 转。可以通过按压两个按键中的一个来提高设置速度，以便更快地达到预
期值。
通过“电子计时器窗口”上的 SET 键，可以选择两种不同类型的运行方式:
—连续的(…); —计时器模式(分钟/小时基数);
为了改变计时器模式(分钟/小时基数)，保持按下设置键几秒钟:
—计时(分): " 000 " —计时(小时): " h00 "
如果不选择运行时间，则搅拌不激活。
显示屏显示倒计时，同时第三个小数点打开，表明计数是有效的。搅拌结束时，仪器停止搅拌，声音信号提示时间结束，显
示器显示“结束”。
4. 维护
除了定期清洁本手册中描述的装置外，无需进行常规或特殊维护。
根据产品保证法，除非事先与当地经销商达成其他协议，否则我们工厂必须进行维修。
仪器必须以原始包装运输，并且必须遵循原始包装上的任何指示（例如托盘化）。
用户有责任在设备表面或内部残留有害物质的情况下，对装置进行适当净化。如对清洁或净化产品的兼容性有疑问，请联系
制造商或分销商。
4.1 清洗
将装置与电源断开，并使用用不可燃非腐蚀性的布。
5. 技术数据
电源
100-240 V / 50-60 Hz
电源
19 W
尺寸(宽x高x深)
655x404x296 毫米 (JLT4) 935x404x296 毫米 (JLT6)
重量(含插头)
13.0 Kg (JLT4) 17.0 Kg (JLT6)
速度范围
10 - 300 转/分，1 转/分步长
时间范围
0-999 分钟/0-99 小时或连续工作
结构材料
环氧漆金属结构
环境温度
5 - 40 °C (41 - 104°F)
储存温度范围
-10… + 60 °C (14 - 140°F)
CN
12
最大湿度
80%
最大湿度
2
6. 附件 / 备件
A00001000 塑料烧杯 1000 毫升 A00001001 玻璃烧杯 1000 毫升
A00001002 透明塑料 Imhoff cone 椎体 A00001003 玻璃Imhoff cone 椎体
A00001004 Imhoff cone 椎体 2位支架 10000235 脚垫
13
7. Wiring diagram / Schema elettrico / Schéma électrique / Esquema eléctrico /
Schaltplan/电路
1. External power supply / Alimentatore di rete / Alimentateur de réseau / Alimentador de red / Netzteil / 外部电源
2. Socket / Presa / Prise de courant / Enchufe / Buchse / 插座
3. Electronic board / Scheda elettronica / Fiche électronique / Tarjeta electrónica / Steckkarte / 电子板
4. Led column / Led colonna / Colonne Led / Columna Led / Spalte-Led / LED 灯带
5. Led electronic board with selector / Scheda elettronica led / Fiche électronique du led / Tarjeta electrónica de led / Led-
Steckkarte / 带选择器的 LED 电子板
6. Counter / Lettore ottico velocità motore / Lecteur optique du vitesse / Unidad óptica de velocidad / Optisches Laufwerk
der Drehzahl / 计数器
7. Motor / Motore / Moteur / Motor / Motor / 电机
8. ON-OFF switch / Interruttore generale / Interrupteur général / Interruptor general / Netzschalter / ON-OFF 开关
9. Switch lighting / Interruttore led colonna / Commutateur de colonne LED / Interruptor de la columna Led / Spalte-Led
Schalter / 开关照明
10. Fuse / Fusibile / Fusibles / Fusible / Sicherung / 保险丝
MULTI
14
8. Declaration of conformity / Dichiarazione di conformità / Déclaration de conformité /
Declaración de conformidad / Konformitätserklärung / 符合性声明
We, the manufacturer VELP Scientifica, under our responsibility declare that the product is manufactured in conformity with
the following standards:
Noi, casa costruttrice VELP SCIENTIFICA, dichiariamo sotto la ns. responsabilità che il prodotto è conforme alle seguenti
norme:
Nous, VELP Scientifica, déclarons sous notre responsabilité que le produit est conforme aux normes suivantes:
Nosotros casa fabricante, VELP Scientifica, declaramos bajo nuestra responsabilidad que el producto es conforme con las
siguientes normas:
Der Hersteller, VELP Scientifica, erklärt unter eigener Verantwortung, dass das Gerät mit folgenden Normen übereinstimmt:
我们，制造商 VELP Scientifica，根据我们的责任声明，该产品的生产符合以下标准。
EN 61010-1 EN 61010-2-051 EN 61326-1
and satisfies the essential requirements of the following directives:
e soddisfa i requisiti essenziali delle direttive:
et qu’il satisfait les exigences essentielles des directives:
y cumple con los requisitos esenciales de las directivas:
und den Anforderungen folgender Richtlinien entspricht:
并满足以下指令的基本要求。
2006/42/EC
2014/30/EU
2015/863/EU (RoHS III)
2012/19/EU (WEEE)
plus modifications / più modifiche / plus modifications / más sucesivas modificaciones / in der jeweils gültigen Fassung / 加
上修改
15
9. Declaration of conformity
We, the manufacturer VELP Scientifica, under our responsibility declare that the product is manufactured in conformity with
the following regulations:
S.I. 2016/1101
Electrical Equipment (Safety) Regulations 2016
S.I. 2016/1091
Electromagnetic Compatibility Regulations 2016
according to the relevant designated standards:
EN 61010-1
Safety requirements for electrical equipment for measurement, control, and laboratory use
Part 1: General requirements
EN 61010-2-051
Particular requirements for laboratory equipment for mixing and stirring
EN 61326-1
Electrical equipment for measurement, control and laboratory use - EMC requirements -
Part 1: General requirements
and satisfies the essential requirements of regulations:
S.I. 2008/1597
Supply of Machinery (Safety) Regulations 2008
S.I. 2012/3032
Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic
Equipment Regulations 2012
S.I. 2013/3113
Waste Electrical and Electronic Equipment Regulations 2013
plus modifications.
16
Thank you for having chosen VELP!
Established in 1983, VELP is today one of the world’s
leading manufacturer of analytical instruments and
laboratory equipment that has made an impact on the
world-wide market with Italian products renowned for
innovation, design and premium connectivity. VELP
works according to ISO 9001, ISO14001 and OHSAS
18001 Quality System Certification.
Our instruments are manufactured in Italy according
to the IEC 1010-1 and CE regulation.
Our product lines:
Grazie per aver scelto VELP!
Fondata nel 1983, VELP è oggi tra i leader mondiali nella
produzione di strumenti analitici e apparecchiature da
laboratorio grazie ai suoi prodotti italiani rinomati per
innovazione, design e connettività.
VELP opera secondo le norme della Certificazione del
Sistema Qualità ISO 9001, ISO14001 e OHSAS 18001.
Tutti i nostri strumenti vengono costruiti in Italia in
conformità alle norme internazionali IEC 1010-1 e alle
regole della marcatura CE.
Le nostre Linee di prodotti:
Analytical instruments
Elemental Analyzers
Digestion Units
Distillation Units
Solvent Extractors
Fiber Analyzers
Dietary Fiber Analyzers
Oxidation Stability Reactor
Consumables
Analytical Instruments
Analizzatori Elementari
Digestori e Mineralizzatori
Distillatori
Estrattori a Solventi
Estrattori di Fibra
Estrattori di Fibra Dietetica
Reattore di Ossidazione
Consumabili
Laboratory Equipment
Magnetic Stirrers
Heating Magnetic Stirrers
Heating Plates
Overhead stirrers
Vortex mixers
Homogenizers
COD Thermoreactors
BOD and Respirometers
Cooled Incubators
Flocculators
Overhead Shakers
Turbidimeter
Radiation Detector
Open Circulating Baths
Pumps
Laboratory Equipment
Agitatori Magnetici
Agitatori Magnetici Riscaldanti
Piastre Riscaldanti
Agitatori ad Asta
Agitatori Vortex
Omogeneizzatori
Termoreattori COD
BOD e Analizzatori Respirometrici
Frigotermostati e Incubatori
Flocculatori
Mescolatore Rotativo
Torbidimetro
Rilevatore di Radiazioni
Bagni Termostatici
Pompe
www.velp.com
VELP Scientifica Srl
20865 Usmate (MB) ITALY
Via Stazione, 16
Tel. +39 039 62 88 11
Fax. +39 039 62 88 120
Distributed by:
We respect the environment by printing our manuals on recycled paper.
Rispettiamo l’ambiente stampando i nostri manuali su carta riciclata.
10003611/B3
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Velp Scientifica JLT4 - JLT6 Manuel utilisateur

Marque
Velp Scientifica
Modèle
JLT4 - JLT6
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents