Zanussi ZWF71243I Manuel utilisateur

Marque: Zanussi

Modèle: ZWF71243I

Catégorie: Machines à laver

Taper: Manuel utilisateur

GETTING

STARTED?

EASY.

User Manual

ZWF71243I

EN User Manual 2

Washing Machine

FR Notice d'utilisation 19

Lave-linge

SAFETY INFORMATION

Before the installation and use of the appliance, carefully read the

supplied instructions. The manufacturer is not responsible for any

injuries or damage that are the result of incorrect installation or

usage. Always keep the instructions in a safe and accessible

location for future reference.

CHILDREN AND VULNERABLE PEOPLE SAFETY-

GULF MARKET

• This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the appliance

by a person responsible for their safety.

• Children should be supervised to ensure that they do not play

with the appliance.

• Keep all packaging away from children and dispose of it

appropriately.

• Keep detergents away from children.

• Keep children and pets away from the appliance when the door

is open.

• If the appliance has a child safety device, it should be activated.

• Children shall not carry out cleaning and user maintenance of

the appliance without supervision.

GENERAL SAFETY

• Do not change the specification of this appliance.

• Do not exceed the maximum load of 7 kg (refer to the

"Programme chart" chapter).

• The operating water pressure at the water entry point from the

outlet connection must be between 0.5 bar (0.05 MPa) and 8

bar (0.8 MPa).

• The ventilation opening in the base must not be covered by a

carpet, mat, or any floor covering.

• The appliance must be connected to the water mains using the

new supplied hose sets, or other new hose sets supplied by

the Authorised Service Centre.

• Old hose sets must not be reused.

• If the mains power supply cable is damaged, it must be

replaced by the manufacturer, its Authorised Service Centre or

similarly qualified persons to avoid an electrical hazard.

• Before any maintenance operation, deactivate the appliance

and disconnect the mains plug from the socket.

• Do not use high pressure water sprays and/or steam to clean

the appliance.

• Clean the appliance with a moist cloth. Use only neutral

detergents. Do not use abrasive products, abrasive cleaning

pads, solvents or metal objects.

• Only for use in air-conditioned environments.

SAFETY INSTRUCTIONS

INSTALLATION

The installation must comply with

relevant national regulations.

• Remove all the packaging and the transit bolts

including rubber bush with plastic spacer.

• Keep the transit bolts in a safe place. If the

appliance is to be moved in the future they must

be reattached to lock the drum to prevent an

internal damage.

• Always take care when moving the appliance as

it is heavy. Always use safety gloves and

enclosed footwear.

• Follow the installation instructions supplied with

the appliance.

• Do not install or use a damaged appliance.

• Do not install or use the appliance where the

temperature can be less than 0°C or where it is

exposed to the weather.

• The floor area on which the appliance is to be

installed must be flat, stable, heat resistant and

clean.

• Make sure that there is air circulation between

the appliance and the floor.

• When the appliance is in its permanent position,

check if it is levelled correctly with the aid of a

spirit level. If it is not, adjust the feet accordingly.

• Do not install the appliance directly above a

floor drain.

• Do not spray water on the appliance and do not

expose it to excessive humidity.

• Do not install the appliance where the appliance

door cannot be fully opened.

• Do not put a closed container to collect

possible water leakage under the appliance.

Contact the Authorised Service Centre to

ensure which accessories can be used.

ELECTRICAL CONNECTION

WARNING! Risk of fire and electric

shock.

• The appliance must be earthed.

• Always use a correctly installed shockproof

socket.

• Make sure that the parameters on the rating

plate are compatible with the electrical ratings

of the mains power supply.

• Do not use multi-plug adapters and extension

cables.

• Make sure not to cause damage to the mains

plug and to the mains cable. Should the mains

cable need to be replaced, this must be carried

out by our Authorised Service Centre.

• Connect the mains plug to the mains socket

only at the end of the installation. Make sure that

there is access to the mains plug after the

installation.

• Do not touch the mains cable or the mains plug

with wet hands.

• Do not pull the mains cable to disconnect the

appliance. Always pull the mains plug.

• This appliance complies with the E.E.C.

Directives.

WATER CONNECTION

• Do not cause damage to the water hoses.

• Before connection to new pipes, pipes not used

for a long time, where repair work has been

carried out or new devices fitted (water meters,

etc.), let the water flow until it is clean and clear.

• Ensure that there are no visible water leaks

during and after the first use of the appliance.

• Do not use an extension hose if the inlet hose is

too short. Contact the Authorised Service

Centre for the replacement of the inlet hose.

• When unpacking the appliance, It is possible to

see water flowing from the drain hose. This is

due to the testing of the appliance with the use

of water in the factory.

• You can extend the drain hose to maximum 400

cm. Contact the Authorised Service Centre for

the other drain hose and the extension.

• Make sure that there is access to the tap after

the installation.

USE

WARNING! Risk of injury, electric

shock, fire, burns or damage to the

appliance.

• Follow the safety instructions on the detergent

packaging.

• Do not put flammable products or items that are

wet with flammable products in, near or on the

appliance.

• Do not wash fabrics which are heavily soiled

with oil, grease or other greasy substances. It

can damage rubber parts of the washing

machine. Prewash such fabrics by hand before

loading them into the washing machine.

• Do not touch the glass door while a programme

operates. The glass can get hot.

• Make sure that all metal objects are removed

from the laundry.

DISPOSAL

WARNING! Risk of injury or

suffocation.

• Disconnect the appliance from the mains

electrical and water supplies.

• Cut off the mains electrical cable close to the

appliance and dispose of it.

• Remove the door catch to prevent children or

pets from becoming trapped in the drum.

• Dispose of the appliance in accordance with

local requirements for the disposal of Waste

Electrical and Electronic Equipment (WEEE).

PRODUCT DESCRIPTION

APPLIANCE OVERVIEW

1 2 3

Worktop

Detergent dispenser

Control panel

Door handle

Rating plate

Feet for levelling the appliance

CHILD SAFETY

This device prevents children or pets to be closed

in the drum.

• Turn the device clockwise, until the groove is

horizontal.

You cannot close the door.

• To close the door, turn the device anticlockwise

until the groove is vertical.

FIXING PLATE KIT (4055171146)

Available from your authorised dealer.

If you install the appliance on a plinth, secure the

appliance in the fixing plates.

Read carefully the instructions supplied with the

accessory.

EASY START

SPECIAL FEATURES

Your new washing machine meets all modern

requirements for an effective treatment of laundry

with low water, energy and detergent consumption

and will care for fabrics.

This appliance is designed with a self cleaning

draining system, allowing light fluff fibers that fall

off the clothes to be drained out with the water, in

such a way that there is no need to access this

area for regular maintenance and cleaning. Refer to

chapter 'Care and Cleaning' for best maintenance

and care of the appliance.

The AutoSense System automatically adjusts the

programme duration to the laundry in the drum to

achieve perfect washing results in the minimum

possible time.

CONTROL PANEL DESCRIPTION

תינכות

תרצוקמ

90°

60°

40°

30°

1200

900

700

םינידע

דיב הסיבכ/רמצ

סנ'ג

הרוטרפמט

הטיחס

הפיטש

זוקינ

הטיחס

20°

ברועמ

םיהכ םידב

טמק לא

תוקד 20 ןונעיר

הנתוכ

יטטניס

ינוכסח הנתוכ

ההשה/לחתה

תפסונ הפיטש

תייהשה

הפיטש

הלחתה תייהשה

3 4

6 578910

Programme knob

Display

Delay Start button ( תייהשה הלחתה )

Door locked indicator

Start/Pause button ( לחתה/ההשה )

Extra Rinse button ( הפיטש תפסונ )

Super Quick button ( תינכות תרצוקמ )

Rinse Hold button ( תייהשה הפיטש )

Spin reduction button (הטיחס)

Temperature button ( הרוטרפמט)

DISPLAY

A CB

The display shows:

A. The delay start .

When you press the delay start button, the

display shows the delay start time.

B. The child lock indicator.

The indicator comes on the display when the

related option is set.

C. This area shows:

• The programme time.

• The alarm codes.

If the appliance has a malfunction, the

display shows the alarm codes. Refer to the

chapter 'Troubleshooting' .

• The display shows the message for

some seconds if:

– You set a option that is not suitable for

the programme.

– You change the programme while it

operates.

PROGRAMME CHART

Programme

Temperature range

Maximum load

Reference spin

speed

Programme description

(Type of load and soil level)

הנתוכ

90°C - Cold

7 kg

1200 rpm

White cotton and coloured cotton. Normal, heavy and

light soil.

הנתוכ ינוכסח

60°C - 40°C

7 kg

1200 rpm

White cotton and fast-coloured cotton. Normal soil.

The energy consumption decreases and the time of the

washing programme is extended, ensuring good washing

results.

יטטניס

60°C - Cold

3 kg

1200 rpm

Synthetic items or mixed fabric items. Normal soil.

םינידע

40°C - Cold

3 kg

700 rpm

Delicate fabrics such as acrylics, viscose and mixed

fabrics requiring gentler washing. Normal soil.

רמצ/הסיבכ דיב

40°C - Cold

1,5 kg

1200 rpm

Machine washable wool, hand washable wool and

other fabrics with «hand washing» care symbol

םידב םיהכ

40°C

3 kg

1200 rpm

Cotton items or mixed fabric items in dark colours.

Normal soil.

Programme

Temperature range

Maximum load

Reference spin

speed

Programme description

(Type of load and soil level)

ברועמ 20°

20°C

2 kg

1200 rpm

Special programme for cotton, synthetic and mixed fabrics

lightly soiled. Select this programme to reduce the energy

consumption. Make sure that the detergent is suitable for

low temperatures in order to have good washing results

הפיטש 7 kg

1200 rpm

To rinse and spin the laundry. All fabrics, except woollens

and very delicate fabrics. Reduce the spin speed accord-

ingly to the type of laundry.

זוקינ 7 kg To drain the water in the drum. All fabrics.

הטיחס 7 kg

1200 rpm

To spin the laundry and to drain the water in the drum. All

fabrics, except woollens and delicate fabrics.

לא טמק

60°C - Cold

1 kg

900 rpm

Synthetic items requiring a gentle wash. Normal and

light soil.

ןונעיר 20 תוקד

30°C

1 kg

900 rpm

Synthetic and delicate items. Light soil items or items

to refresh.

ג'סנ

60°C - Cold

3 kg

1200 rpm

Items in denim and jersey. Normal soil.

30'@ 30°

30°C

3 kg

700 rpm

A short cycle for synthetic and delicate items with

light soil level or for items to freshen up.

1) Standard programmes for the Energy Label consumption values. According to regulation

1061/2010, these programmes are respectively the «Standard 60°C cotton programme» and the «Stand-

ard 40°C cotton programme». They are the most efficient programmes in terms of combined energy and

water consumption for washing normally soiled cotton laundry.

The water temperature of the washing phase may differ from the temperature declared for the

selected programme.

2) During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't

rotate or doesn't rotate properly, but this is normal for this programme.

3) The appliance performs the short heating phase if the water temperature is below 20°C. The appliance

can show the temperature setting as “cold”.

4) The default spin speed is 700 rpm.

5) To reduce creasing, this cycle regulates the water temperature and performs a soft wash and spin

phase. The appliance adds some rinses.

Programme options compatibility

Programme הטיחס תייהשה הפיטש

תינכות תרצוקמ

הפיטש תפסונ תייהשה הלחתה

הנתוכ ■ ■ ■ ■ ■

הנתוכ ינוכסח

■ ■ ■ ■

Programme הטיחס תייהשה הפיטש

תינכות תרצוקמ

הפיטש תפסונ תייהשה הלחתה

יטטניס

■ ■ ■ ■ ■

םינידע ■ ■ ■ ■

רמצ/הסיבכ דיב ■ ■ ■

םידב םיהכ ■ ■ ■ ■

ברועמ 20° ■ ■ ■ ■

הפיטש ■ ■ ■ ■

זוקינ ■

הטיחס ■ ■

לא טמק ■ ■ ■ ■

ןונעיר 20 תוקד ■ ■

ג'סנ ■ ■ ■

30'@ 30° ■

1) When you set the תינכות תרצוקמ option, we recommend that you decrease the quantity of the laundry. It is

possible to keep the full load but the washing results can be unsatisfactory. Recommended load: cotton:

3,5 kg, synthetics and delicates: 1,5 kg.

CONSUMPTION VALUES

Stated values are obtained in laboratory conditions with relevant standards. Different cau-

ses can change the data: the quantity and type of laundry and ambient temperature. Wa-

ter pressure, the supply voltage and the temperature of inlet water may also affect the

washing programme duration.

Technical specifications may be changed without prior notice to improve the quality of

product.

At the start of the programme, the display shows the programme duration for the maxi-

mum load capacity.

During the washing phase the programme duration is automatically calculated and can be

greatly reduced if the laundry load is lower than the maximum load capacity (e.g. Cotton

60°C, maximum load capacity 7 kg, the programme duration exceeds 2 hours; actual load

1 kg, the programme duration will be less than 1 hour).

When the appliance is calculating the real programme duration a dot flashes in the dis-

play.

Programmes Load (kg)

Energy con-

sumption

(kWh)

Water con-

sumption (litre)

Approximate pro-

gramme duration (mi-

nutes)

Cottons 60°C 7 1,34 68 157

Cotton Energy Saving Pro-

gramme 60°C

7 0,92 45 250

Cottons 40°C 7 0,78 61 157

Synthetics 40°C 3 0,60 56 103

Delicates 40°C 3 0,55 59 81

Wool/Handwash 30°C 1,5 0,45 62 75

1) «Cotton Energy Saving programme » at 60°C with a load of 7 kg is the reference programme for the

data entered in the energy label, in compliance with EU Commission Directive 95/12/EC and measured

according to EN 60456/2005.

Off Mode (W) Left On Mode (W)

0,48 0,48

The information given in the chart above is compliant with the EU Commission regulation 1015/2010

implementing directive 2009/125/EC

OPTIONS

הרוטרפמט

With this option you can change the default

temperature.

Indicator = cold water.

The indicator of the set temperature comes on.

הטיחס

With this option you can change the default spin

speed.

The indicator of the set speed comes on.

תייהשה הפיטש

Set this option to prevent the laundry creases.

The related indicator comes on.

There is water in a drum when the

programme completes. To drain the

water refer to ‘At the end of the

programme’.

תינכות תרצוקמ

Press this button to decrease the programme

duration.

Set this option for items with light soil or items to

refresh.

הפיטש תפסונ

With this option you can add some rinses to a

washing programme.

Use this option for persons allergic to detergents

and in areas where the water is soft.

The related indicator comes on.

תייהשה הלחתה

With this option you can delay the start of a

programme from 30 minutes to 20 hours.

The display shows the related indicator.

DOOR LOCKED INDICATOR

The indicator shows when the door can be

opened:

• The indicator is on: the door cannot be opened.

• The indicator flashes: the door is opening in

some minutes.

• The indicator is off: the door can be opened.

SETTINGS

CHILD LOCK

With this option you can prevent that the children

play with the control panel.

• To activate/deactivate this option, press

Temperature and Spin at the same time until the

indicator comes on/goes off.

You can activate this option:

• After you press לחתה/ההשה : the options and the

programme knob are locked.

• Before you press לחתה/ההשה : the appliance

cannot start.

ACOUSTIC SIGNALS

The acoustic signals operate when:

• The programme is completed.

• The appliance has a malfunction.

To deactivate/activate the acoustic signals,

press Rinse Hold and Quick at the same time for 6

seconds.

If you deactivate the acoustic signals,

they continue to operate when the

appliance has a malfunction.

PERMANENT EXTRA RINSE

With this option you can permanently have an extra

rinse when you set a new programme.

• To activate/deactivate this option touch the

buttons Rinse Hold and Extra Rinse at the same

time until the indicator of הפיטש תפסונ button

comes on/goes off.

BEFORE FIRST USE

During installation or before first use

you may observe some water in the

appliance. This is residual water left in

the appliance after a full functional test

in the factory to ensure the appliance

is delivered to customers in perfect

working order and is no cause for

concern.

1. Connect the mains plug to the mains socket.

2. Open the water tap.

3. Put a small quantity of detergent in the

compartment for washing phase.

4. Set and start a programme for cotton at the

highest temperature without laundry.

This removes all possible dirt from the drum and the

tub.

DAILY USE

WARNING! Refer to Safety chapters.

LOADING THE LAUNDRY

Open the water tap. Connect the mains plug to the

mains socket.

1. Pull the door handle to open the appliance

door.

2. Put the laundry in the drum, one item at a time.

3. Shake the items before you put them in the

appliance.

Make sure not to put too much laundry in the drum.

Refer to max. loads indicated in "Programme chart".

4. Close the door.

CAUTION! Make sure that no laundry

stays between the seal and the door.

There is a risk of water leakage or

damage to the laundry.

Washing heavily oiled, greasy stains

could cause damage rubber parts of

the washing machine.

USING DETERGENT AND ADDITIVES

1. Measure out the detergent and the fabric

conditioner.

2. Put the detergent and the fabric conditioner

into the compartments.

3. Carefully close the detergent drawer.

DETERGENT COMPARTMENTS

Detergent compartment for

washing phase.

If you use liquid detergent, put it

immediately before you start the

programme.

Compartment for liquid additives

(fabric conditioner, starch).

CAUTION! Do not

exceed the MAX

level.

Flap for powder or liquid deter-

gent.

LIQUID OR POWDER DETERGENT

The default position of

the flap is A (powder de-

tergent).

To use liquid detergent:

1. Remove the drawer.

Push the drawer edge in

the place with the arrow

(PUSH) to remove the

drawer easily.

2. Adjust the flap in posi-

tion B.

3. Put back the drawer in

the recess.

When you use the liquid detergent:

• Do not use gelatinous or thick liq-

uid detergents.

• Do not put more liquid then 120

ml.

• Do not set the delay start.

When the flap is in posi-

tion B and you want to

use powder detergent:

1. Remove the drawer.

2. Adjust the flap in po-

sition A.

3. Put back the drawer

in the recess.

SETTING A PROGRAMME

1. Turn the programme knob to switch the

appliance on and set the programme:

• The indicator of the button לחתה/ההשה

flashes.

• The display shows the programme duration.

2. If necessary, change the temperature and the

spin speed or add available options. When you

activate an option, the indicator of the set

option comes on.

If you set something incorrect, the

display shows the message .

STARTING A PROGRAMME WITHOUT THE

DELAY START

Press the button לחתה/ההשה .

• The indicator of the button לחתה/ההשה stops

to flash and stays on.

• The programme starts, the door locks, the

indicator is on.

• The programme time decreases with steps

of one minute.

The drain pump can operate for a

short time at the beginning of the

washing cycle.

STARTING A PROGRAMME WITH THE DELAY

START OPTION

1. Press the button תייהשה הלחתה again and again

until the display shows the delay you want to

set. The delay start indicator comes on.

2. Press the button לחתה/ההשה :

• The door is locked and the indicator is

on.

• The appliance starts the countdown.

• When the countdown is completed, the

programme starts automatically.

You can cancel or change the set of

the תייהשה הלחתה option before you

press the button לחתה/ההשה . After

pressing the button לחתה/ההשה you can

only cancel the תייהשה הלחתה option.

To cancel the תייהשה הלחתה option:

a. Press the button לחתה/ההשה to set the

appliance to pause. The indicator of button

לחתה/ההשה flashes.

b. Press the button תייהשה הלחתה until the

display shows .

Press the button לחתה/ההשה again to start

the programme immediately.

INTERRUPTING A PROGRAMME AND

CHANGING THE OPTIONS

You can change only some options before they

operate.

1. Press the button לחתה/ההשה .

The indicator flashes.

2. Change the options.

3. Press the button לחתה/ההשה again.

The programme continues.

CANCELLING A RUNNING PROGRAMME

1. Turn the programme knob to position to

cancel the programme and to deactivate the

appliance.

2. Turn the programme knob again to activate the

appliance. Now, you can set a new washing

programme.

Before starting the new programme

the appliance could drain the water. In

this case, make sure that the detergent

is still in the detergent compartment, if

not fill the detergent again.

OPENING THE DOOR

While a programme or the תייהשה הלחתה operates,

the appliance door is locked. The indicator is

on.

CAUTION! If the temperature and

level of the water in the drum are too

high and the drum still rotates, you

cannot open the door.

To open the door during the first minutes of the

cycle or when the תייהשה הלחתה operates:

1. Press the button לחתה/ההשה to pause the

appliance.

2. Wait until the indicator goes off.

3. You can open the door.

4. Close the door and touch the button לחתה/ההשה

again. The programme (or the תייהשה הלחתה )

continues.

AT THE END OF THE PROGRAMME

• The appliance stops automatically.

• The acoustic signal operates (if it is activated).

• In the display comes on.

• The indicator of the button לחתה/ההשה goes off.

• The door lock indicator goes off.

Turn the programme knob to position to

deactivate the appliance.

• You can open the door.

• Remove the laundry from the appliance. Make

sure that the drum is empty.

• Close the water tap.

• Keep the door and the detergent drawer ajar, to

prevent the mildew and odours.

The washing programme is completed, but

there is water in the drum:

• The drum turns regularly to prevent the creases

in the laundry.

• The indicator תייהשה הפיטש stays on to remind

you to drain the water.

• The door lock indicator is on. The indicator

of button לחתה/ההשה is off. The door stays

locked.

• You must drain the water to open the door.

Draining the water:

1. To drain the water.

• Set a

זוקינ or a הטיחס programme.

• Press the button לחתה/ההשה . The appliance

drains the water and spins.

2. When the programme is completed and the

door lock indicator goes off, you can open

the door.

3. Turn the programme knob to the position to

deactivate the appliance.

STAND BY

Some minutes after the end of the washing

programme, if you do not deactivate the appliance,

the energy saving status activates. The energy

saving status decreases the energy consumption

when the appliance is on the standby:

• All indicators and the display go off.

• The indicator of button Start flashes slowly.

Press one of the buttons to deactivate the energy

saving status.

HINTS AND TIPS

THE LAUNDRY LOAD

• Divide the laundry in: white, coloured,

synthetics, delicates and wool.

• Obey the washing instructions that are on the

laundry care labels.

• Do not wash white and coloured items together.

• Some coloured items can discolour with the first

wash. We recommend that you wash them

separately for the first times.

• Turn multilayered fabrics, wool and items with

painted illustrations inside out.

• Remove hard stains with a special detergent.

• Wash and pre-treat heavy soil stains before

putting items in drum

• Be careful with the curtains. Remove the hooks

and put the curtains in a washing bag or

pillowcase.

• Do not wash laundry without hems or with cuts.

Use a washing bag to wash small and/or

delicate items (e.g. underwired bras, belts,

tights, shoelaces, ribbons, etc. ).

• A very small load can cause balance problems

with the spin phase. If this occurs, adjust

manually the items in the tub and start the spin

phase again.

• Avoid washing garments full of long animal hair

or poor quality garments releasing lots of fluff

that could block the drain circuit and therefore

requiring the Service assistance.

• Button up pillowcases, close zippers, hooks and

poppers. Tie up belts, cords, shoelaces, ribbons

and any other loose elements.

• Empty the pockets and unfold the items.

STUBBORN STAINS

For some stains, water and detergent is not

sufficient.

We recommend that you pre-treat these stains

before you put the items in the appliance.

Special stain removers are available. Use the

special stain remover that is applicable to the type

of stain and fabric.

DETERGENTS AND ADDITIVES

• Only use detergents and additives specially

made for washing machines:

– powder detergents for all types of fabric,

– powder detergents for delicate fabrics (40

°C max) and woollens,

– liquid detergents, preferably for low

temperature wash programmes (60 °C max)

for all types of fabric, or special for woollens

only.

• Do not mix different types of detergents.

• To help the environment, do not use more than

the correct quantity of detergent.

• Obey the instructions that you find on the on

packaging of these products.

• Use the correct products for the type and colour

of the fabric, the programme temperature and

the level of soil.

• If your appliance does not have the detergent

dispenser with the flap device, add the liquid

detergents with a dosing ball (supplied by the

detergent's manufacturer).

ECOLOGICAL HINTS

• Always start a washing programme with the

maximum load of laundry allowed.

• If necessary, use a stain remover when you set a

programme with a low temperature.

• To use the correct quantity of detergent, check

the water hardness of your domestic system.

Refer to "Water hardness".

WATER HARDNESS

If the water hardness in your area is high or

moderate, we recommend that you use a water

softener for washing machines. In areas where the

water hardness is soft it is not necessary to use a

water softener.

To know the water hardness in your area, contact

your local water authority.

Use the correct quantity of the water softener.

Obey the instructions that you find on the

packaging of the product.

CARE AND CLEANING

WARNING! Refer to Safety chapters.

EXTERNAL CLEANING

Clean the appliance with soap and warm water

only. Fully dry all the surfaces.

CAUTION! Do not use alcohol,

solvents or chemical products.

DESCALING

If the water hardness in your area is high or

moderate, we recommend that you use a water

descaling product for washing machines.

Regularly examine the drum to prevent limescale

and rust particles.

To remove rust particles use only special products

for washing machines. Do this separately from the

laundry wash.

Always obey the instructions that you

find on the packaging of the product.

MAINTENANCE WASH

With the low temperature programmes it is possible

that some detergent stays in the drum. Perform a

maintenance wash regularly. To do this:

• Remove all laundry from the drum.

• Select the cotton programme with the highest

temperature with a small quantity of detergent.

DOOR SEAL

This appliance is designed with a self cleaning

draining system, allowing light fluff fibers that fall

off the clothes to be drained out with the water, in

such a way that there is no need to access this

area for regular maintenance and cleaning.

Regularly examine the seal and remove all objects

from the inner part. Coins, buttons, other small

items forgotten in the pockets of your clothes are

deposited during the washing cycle in the special

double lip trap in the porthole seal, where they can

be conveniently recovered at the end of the cycle.

CLEANING THE DETERGENT DISPENSER

1 2 3 4

5 6

CLEANING THE INLET HOSE AND THE VALVE FILTER

1 2 3

45°

20°

FROST PRECAUTIONS

If the appliance is installed in an area where the

temperature can be less than 0 °C, remove the

remaining water from the inlet hose and the drain

pump.

Do this procedure also when you want

to do the emergency drain.

1. Disconnect the mains plug from the mains

socket.

2. Remove the water inlet hose.

3. Remove the drain hose from the rear support

and unhook it from sink or spigot.

4. Put the ends of the drain and inlet hose in a

container. Let the water flow out of the hoses.

5. Set any selected programme with option

הטיחס

זוקינו and let it operate until the end of the cycle.

6. When no more water flows, install the inlet

hose and the drain hose again.

7. Press the button to deactivate the

appliance.

WARNING! Make sure that the

temperature is more than 0°C before

you use the appliance again. The

manufacturer is not responsible for

damages caused by low temperatures.

TROUBLESHOOTING

WARNING! Refer to Safety chapters.

INTRODUCTION

The appliance does not start or it stops during

operation.

First try to find a solution to the problem (refer to

the table). If the problem persists, contact the

Authorised Service Centre.

With some problems, the acoustic signals

operate and the display shows an alarm

code:

• - The appliance does not fill with water

properly. Start the appliance again by pressing

לחתה/ההשה button. After 10 seconds the door will

be unlocked.

• - The appliance does not drain the water.

• - The appliance door is open or not

closed correctly. Please check the door!

• - The mains supply is unstable. Wait until

the mains supply is stable.

WARNING! Deactivate the appliance

before you do the checks.

POSSIBLE FAILURES

Problem Possible solution

The programme does not

start.

• Make sure that the mains plug is connected to the mains socket.

• Make sure that the appliance door is closed.

• Make sure that there is not a damaged fuse in the fuse box.

• Make sure that the Start/Pause has been pressed.

• If the delay start is set, cancel the setting or wait for the end of

countdown.

• Deactivate the Child Lock function if it is on (if available).

The appliance does not fill

with water properly.

• Make sure that the water tap is open.

• Make sure that the pressure of the water supply is not too low. For

this information, contact your local water authority.

• Make sure that the water tap is not clogged.

• Make sure that the filter of the inlet hose and the filter of the valve

are not clogged. Refer to “Care and cleaning”.

• Make sure that the inlet hose has no kinks or bends.

• Make sure that the connection of the water inlet hose is correct.

• Make sure that the drain hose is in the correct position. The hose

may be too low.

The appliance does not

drain the water.

• Make sure that the sink spigot is not clogged.

• Make sure that the drain hose has no kinks or bends.

• Make sure that the connection of the drain hose is correct.

• Set the drain programme if you set a programme without drain

phase.

• Set the drain programme if you set an option which ends with water

in the drum.

• If above mentioned solutions do not help, contact the Authorised

Service Centre (as the filter of the drain pump may be clogged).

The spin phase does not

operate or the washing cy-

cle lasts longer than usual-

ly.

• Set the spin programme.

• Adjust manually the items in the tub and start the spin phase again.

This problem may be caused by balance problems.

• If above mentioned solutions do not help, contact the Authorised

Service Centre (as the filter of the drain pump may be clogged).

There is water on the floor. • Make sure that the couplings of the water hoses are tight and there

is not water leakages.

• Make sure that the inlet hose and/or the drain hose have no dam-

ages.

• Make sure you use the correct detergent and the correct quantity of

it.

You cannot open the appli-

ance door.

• Make sure that the washing programme is finished.

• Set the drain or the spin programme if there is water in the drum.

The appliance makes an

unusual noise.

• Make sure the levelling of the appliance is correct. Refer to 'Installa-

tion Instruction'.

• Make sure that the packaging and/or the transit bolts are removed.

Refer to 'Installation Instruction'.

• Add more laundry in the drum. The load may be too small.

The cycle is shorter than

the time displayed.

The appliance calculates a new time according to the laundry load.

See the ‘Consumption Values’ chapter.

Problem Possible solution

The cycle is longer than

the time displayed.

An unbalanced laundry load increases the duration time. This is a nor-

mal behaviour of the appliance.

The washing results are

not satisfactory.

• Increase the detergent quantity or use a different detergent.

• Use special products to remove the stubborn stains before you

wash the laundry.

• Make sure that you set the correct temperature.

• Decrease the laundry load.

You cannot set an option. • Make sure that you press only the wanted button(s).

After the check, activate the appliance. The

programme continues from the point of interruption.

If the problem occurs again, contact the Authorised

Service Centre.

If the display shows other alarm codes. Deactivate

and activate the appliance. If the problem

continues, contact the Service.

SERVICE

We recommend the use of original spare parts.

When contacting the Authorised Service Centre,

make sure that these data are available. You can

find the information on the rating plate: model, PNC

and Serial Number. (Mod., Prod. No., Ser. No.)

TECHNICAL DATA

Dimension Width/ Height/ Depth/ To-

tal depth

600 mm/ 850 mm/ 559 mm/ 578 mm

Electrical connection Voltage

Overall power

Fuse

Frequency

230 V

2200 W

10 A

50 Hz

Level of protection against ingress of solid particles and

moisture ensured by the protective cover, except where

the low voltage equipment has no protection against

moisture

IPX4

Water supply pressure Minimum

Maximum

0,5 bar (0,05 MPa)

8 bar (0,8 MPa)

Water supply

1) Cold water

Maximum Load Cotton 7 kg

Energy Efficiency Class A+++

Spin Speed Maximum spin speed 1151 rpm

1) Connect the water inlet hose to a water tap with a 3/4'' thread.

ENVIRONMENTAL CONCERNS

Recycle materials with the symbol . Put the

packaging in relevant containers to recycle it. Help

protect the environment and human health by

recycling waste of electrical and electronic

appliances. Do not dispose of appliances marked

with the symbol with the household waste.

Return the product to your local recycling facility or

contact your municipal office.

INFORMATIONS DE SÉCURITÉ

Avant d'installer et d'utiliser cet appareil, lisez soigneusement les

instructions fournies. Le fabricant ne pourra être tenu pour

responsable des blessures et dégâts résultant d'une mauvaise

installation ou utilisation. Conservez toujours les instructions dans

un lieu sûr et accessible pour vous y référer ultérieurement.

SÉCURITÉ DES ENFANTS ET DES PERSONNES

VULNÉRABLES - MARCHÉ DU GOLFE

• Cet appareil n'est pas conçu pour être utilisé par des

personnes (y compris des enfants) dont les facultés physiques,

sensorielles ou mentales sont réduites, ou qui manquent

d'expérience et de connaissances, à moins qu'une personne

responsable de leur sécurité ne les supervise ou leur donne

des instructions sur la manière de l'utiliser.

• Ne laissez pas les enfants jouer avec l'appareil.

• Ne laissez pas les emballages à la portée des enfants et jetez-

les convenablement.

• Ne laissez pas les détergents à la portée des enfants.

• Tenez les enfants et les animaux éloignés de l'appareil lorsque

la porte est ouverte.

• Si l'appareil est équipé d'un dispositif de sécurité enfants, nous

vous recommandons de l'activer.

• Les enfants ne doivent pas nettoyer ni entreprendre une

opération de maintenance sur l'appareil sans surveillance.

SÉCURITÉ GÉNÉRALE

• Ne modifiez pas les caractéristiques de cet appareil.

• Respectez la charge maximale de 7 kg (reportez-vous au

chapitre « Tableau des programmes »).

• La pression de l'eau en service au niveau du point d'entrée en

provenance de l'arrivée d'eau doit être comprise entre 0,5 bar

(0,05 MPa) et 8 bar (0,8 MPa).

• Les orifices d'aération situés à la base ne doivent pas être

obstrués par de la moquette, un tapis, ou tout type de

revêtement de sol.

• L'appareil doit être raccordé à l'arrivée d'eau à l'aide des tuyaux

neufs fournis, ou d'autres tuyaux neufs fournis par le service

après-vente agréé.

• N'utilisez pas de tuyaux provenant d'anciens appareils.

• Si le câble d'alimentation est endommagé, il doit être remplacé

par le fabricant, un service de maintenance agréé ou un

technicien qualifié afin d'éviter tout danger lié à l'électricité.

• Avant toute opération d'entretien, éteignez l'appareil et

débranchez la fiche de la prise secteur.

• Ne pulvérisez pas d'eau ni de vapeur à haute pression pour

nettoyer l'appareil.

• Nettoyez l'appareil avec un chiffon humide. Utilisez uniquement

des produits de lavage neutres. N'utilisez pas de produits

abrasifs, de tampons à récurer, de solvants ni d'objets

métalliques.

• À utiliser uniquement dans des environnements climatisés.

CONSIGNES DE SÉCURITÉ

INSTRUCTIONS D'INSTALLATION

L'installation doit être confirme aux

réglementations nationales en vigueur.

• Retirez l'intégralité de l'emballage et les boulons

de transport, y compris le joint en caoutchouc et

l'entretoise en plastique.

• Conservez les boulons de transport en lieu sûr.

Si l'appareil doit être de nouveau déplacé, les

boulons doivent être réutilisés pour maintenir le

tambour en place et éviter tout dégât interne.

• Soyez toujours vigilants lorsque vous déplacez

l'appareil car il est lourd. Utilisez toujours des

gants de sécurité et des chaussures fermées.

• Suivez scrupuleusement les instructions

d'installation fournies avec l'appareil.

• N'installez pas et ne branchez pas un appareil

endommagé.

• N'installez pas l'appareil ou ne l'utilisez pas dans

un endroit où la température ambiante est

inférieure à 0 °C ou dans un endroit exposé aux

intempéries.

• L'appareil doit être installé sur un sol plat,

stable, résistant à la chaleur et propre.

• Assurez-vous que de l'air circule entre l'appareil

et le sol.

• Une fois l'appareil installé à son emplacement

permanent, vérifiez qu'il est bien de niveau à

l'aide d'un niveau à bulle. S'il n'est pas de

niveau, réglez les pieds jusqu'à ce qu'il le soit.

• N'installez pas l'appareil directement au-dessus

d'une évacuation dans le sol.

• Ne vaporisez pas d'eau sur l'appareil et ne

l'exposez pas à une humidité excessive.

• N'installez pas l'appareil dans un endroit où il ne

pourrait pas être complètement ouvert.

• Ne placez aucun récipient fermé sous l'appareil

pour récupérer tout éventuel écoulement.

Contactez le service après-vente agréé pour

connaître les accessoires disponibles.

BRANCHEMENT ÉLECTRIQUE

AVERTISSEMENT! Risque

d'incendie ou d'électrocution.

• L’appareil doit être relié à la terre.

• Utilisez une prise correctement installée et

protégée contre les chocs.

• Vérifiez que les paramètres figurant sur la

plaque signalétique correspondent aux données

électriques de votre réseau.

• L’appareil ne doit pas être raccordé à l’aide

d'une prise multiple ou d'un prolongateur.

• Veillez à ne pas endommager la fiche secteur ni

le câble d’alimentation. Le remplacement du

La page charge ...

Zanussi ZWF71243I Manuel utilisateur

Marque: Zanussi

Modèle: ZWF71243I

Catégorie: Machines à laver

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Zanussi ZWF71243I User manual

Zanussi ZWF71243I Manuel utilisateur

Zanussi ZWF71243I Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents