Intermec MobileLAN access 2106 Guide de démarrage rapide

Intermec
Marque
Intermec
Modèle
MobileLAN access 2106
Catégorie
Points d'accès WLAN
Taper
Guide de démarrage rapide
Intermec’s MobileLAN™ access family access points delivers reliable and seamless wireless
performance to almost any operational environment. The MobileLAN access 2106 is
designed for standards-based connectivity and it has an IEEE 802.11a radio.
The 2106 is compatible with older Ethernet 10BaseT infrastructure; however, your installed
infrastructure base of cable and switching hardware may limit system data throughput. To
achieve the best performance possible, your installation procedure should include a test to
verify the Ethernet performance. All hubs and switches should be rated for dual speed
performance at 10/100 Mbps. The connection cabling should meet Level II test standards
described in TIA/EIA TSB #67. Servers and clients should be 850 MHz Pentium machines or
better.
Use this quick start guide to help you understand the 2106 ports and LEDs. You can also use
this quick start guide to learn how to install the mounting bracket, how to connect the 2106
to power and to your network, and how to use the MobileLAN access Utility to configure its
IP address. Once you assign the 2106 an IP address, you can continue configuring it using a
Web browser.
Out of the Box
MobileLAN™ access 2106
Heading 1
About the 2106Safety First
Quick Start Guide
More Information
Specifications
Caution
Government regulatory agencies mandate that the antenna not be
alterable. Therefore, the access point uses a custom antenna connector. Do
not attempt to use a different antenna or you may damage the connector
and the access point.
Conseil
Les agences responsables de la réglementation gouvernmentale exigent
que l’antenne ne soit pas modifiable. Par conséquent, le point d’accès est
doté d’un connecteur d’antenne personnalisé. Ne pas essayer d’utiliser une
antenne différente au risque d’endommanger le connecteur et le point
d’accès.
Caution
You must use the appropriate Intermec power supply with this device or
equipment damage may occur.
Conseil
Vour deves utiliser la source d’alimentation Intermec adéquate avec cet
appareil sinon vous risquez d’endommager l’équipement.
MobileLAN access 2106 Quick Start Guide
*072215-004*
*072215-004*
For more information on using the 2106, please see:
• MobileLAN access System Manual (Part No. 067150)
• Intermec Web site at www.intermec.com
To order access point accessories and antennas, contact your local Intermec representative.
Physical dimensions 14.7 cm x 9.3 cm x 3.5 cm
(5.8 in x 3.7 in x 1.4 in)
Weight 232 g (0.5 lb)
Electrical rating ~100 to 240V
1.0A
50 to 60 Hz
Operating temperature 0°C to 45°C (32°F to 113°F)
Storage temperature -20°C to 70°C (-4°F to 158°F)
Humidity 10 to 90%, non-condensing
Frequency band 5.15 to 5.35 GHz
Power output 40 mW
Data rate 802.11 compliant mode: 54 Mbps, 48 Mbps, 36 Mbps, 24 Mbps,
12 Mbps, 6 Mbps with automatic fallback for increased range
Turbo mode: 72 Mbps, 48 Mbps, 36 Mbps, 24 Mbps, 12 Mbps
with automatic fallback for increased range
Channels 802.11 compliant mode: 8 (North America)
Turbo mode: 3 (North America)
Receiver sensitivity 54 Mbps: -69 dBm
CAUTION
!
CAUTION
!
6001 36th Avenue West
Everett, WA 98203
U.S.A.
www.intermec.com
© 2002 Intermec Technologies Corp.
All Rights Reserved
Getting Started Guide
M
ob
ileLAN™
acc
ess 2106
Document package
MobileLAN access
2106 and mounting
bracket
Power cord
Power supply
CD
This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org).
This product includes cryptographic software written by Eric Young ([email protected]).
Defining the LEDs, Ports, and Antenna Positions
MobileLAN™ access 2106 Quick Start Guide
1 2
Mounting the 2106 Connecting the 2106
3
Check for Software Upgrades
You should check the Intermec MobileLAN Web site at http://mobilelan.intermec.com for
free software downloads and the latest documentation. To upgrade your access point
software, follow the instructions in the MobileLAN access System Manual.
Click Software
Downloads.
4
Setting an Initial IP Address
Install the MobileLAN access Utility on your PC by inserting the enclosed CD,
clicking Install Software, and following the instructions that appear on your screen.
You can also download the software from http://mobilelan.intermec.com.
Note: Your PC must be on the same Ethernet segment as the access point.
Or, if your PC is communicating wirelessly with the access point, you must
have an active radio connection.
Start the utility.
Configure parameters A through C. See the screen to the right.
Click Set.
Reboot the access point by disconnecting it from and reconnecting it to a power
source. The Status box lets you know when the IP address is successfully set.
1
5
4
3
2
Congratulations!
Your wireless end devices can now begin transmitting data packets through the 2106 to your
wired network. To continue configuring the access point, from the Actions menu choose
Configure Access Point. Your Web browser application (for example, Internet Explorer) starts
and the Access Point Login screen appears.
A
Click the down arrow and
choose Set IP Address.
B
Enter the Ethernet MAC
address of the access point
(printed on a label on the
access point).
C
Enter the new IP address of
the access point.
5
You can install the 2106 horizontally on a desk or counter, or you can install it vertically to a
wall using the wall bracket that ships with it.
To mount the 2106 using the wall bracket, you need two #5 or M3 screws (appropriate for the
surface on which you are mounting the bracket), a drill and drill bit appropriate for the
mounting screws, and a screwdriver.
To mount the 2106 vertically
1
2
Use the mounting bracket
as a template to mark the
location of the mounting
holes on the mounting
surface.
Drill the mounting holes.
Follow the instructions in
the illustration to the right.
Note: Intermec offers a
variety of mounting bracket
kits and accessories. For a
complete list, see the
MobileLAN access System
Manual (Part No. 067150).
3
Connect the 2106 to your network by using an Ethernet cable to connect the
Ethernet port to an Ethernet drop.
Connect the 2106 to power. You can either use an AC power supply with the
appropriate power cord or power over Ethernet. To use power over Ethernet, you use
an Ethernet cable to connect the Ethernet port to a MobileLAN splitter, which is
connected to a MobileLAN power bridge. For help, see the documentation that
shipped with your power bridge.
1
2
Fit the slots on the back of
the 2106 over the hooks on
the mounting bracket and
snap the 2106 into place.
Screws fasten
into mounting
surface.
Mounting screw (not
provided) (2 places)
Ethernet
drop
Power
supply
Plug the power supply
into the power port.
Plug the AC power cord
into an AC power outlet.
Power
Remains on after
the 2106 boots.
Wired LAN
Flashes when a frame is transmitted
or received on the Ethernet port.
Root/error
Flashes if this 2106 is
configured as the root. It
remains on if an error has
occurred.
Radio
Flashes when a frame is
transmitted or received on the
Radio port.
Use this position
when storing the
2106.
Use this
p
osition
when the 21
06
is
m
ou
nte
d
o
n
a
deskto
p.
U
se this
p
osition
wh
e
n
t
h
e
21
06
is
m
ou
nte
d
t
o
a
w
a
ll
.
0
90
9
1
80
Power
port
10BaseT/100BaseTx
Ethernet port
  • Page 1 1
  • Page 2 2

Intermec MobileLAN access 2106 Guide de démarrage rapide

Intermec
Marque
Intermec
Modèle
MobileLAN access 2106
Catégorie
Points d'accès WLAN
Taper
Guide de démarrage rapide
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes