Intermec MobileLAN access WA21 Guide de démarrage rapide
- Taper
- Guide de démarrage rapide
Intermec’s MobileLAN™access family of access points delivers reliable and seamless wireless
performance to almost any operational environment. The MobileLAN access WA21 can be
powered either by AC power or by power over Ethernet to make installation easier. It is
designed for standards-based connectivity and it may have up to two of the following radios
installed:
• IEEE 802.11b
• IEEE 802.11a
The WA21 with an IEEE 802.11b radio installed is Wi-Fi certified for
interoperability with other 802.11b wireless LAN devices.
This quick start guide helps you to understand the WA21 ports and LEDs. You can also use
this quick start guide to get an overview of how to install the WA21, how to connect the
WA21 to power and to your network, and how to use the MobileLAN access Utility to
configure its IP address. Once you assign the WA21 an IP address, you can continue
configuring it using a Web browser interface or a Telnet session.
For complete instructions on how to install, operate, configure, maintain, and troubleshoot
your WA21, see the MobileLAN access System Manual (P/N 067150). Please visit the Intermec
Web site at www.intermec.com to download this manual and many other current manuals in
PDF format. Or, you can order printed documentation from your local Intermec
representative.
Out of the Box
MobileLAN
™
access WA21
Heading 1
About the WA21
Safety First
Quick Start Guide
Specifications
Note: The WA21 does not ship with an antenna (except for one 802.11a
configuration that ships with non-removable antennas). For a list of antennas and
antenna accessories, see the MobileLAN access System Manual or contact your local
Intermec representative.
MobileLAN access WA21 Quick Start Guide
*072828-001*
*072828-001*
Physical dimensions 9.5 cm x 23.6 cm x 35.5 cm
(3.75 in x 9.3 in x 14.0 in)
AC electrical rating
Standard ~100 to 240 V, 1.0 to 0.5A, 50 to 60 Hz
Heater (optional) ~100 to 120 V, 1.0A, 50 to 60 Hz
or ~200 to 240 V, 0.5A, 50 to 60 Hz
Power over Ethernet
electrical rating N 48V, 315 mA
Environmental rating IP 54
Operating temperature
Standard -25°C to 70°C (-13°F to 158°F)
Heater (optional), AC only -30°C to 70°C (-22°F to 158°F)
Heater/insulated bag
(optional), AC only -30°C to 0°C (-13°F to 32°F)
Storage temperature -40°C to 70°C (-40°F to 158°F)
Humidity 10 to 90%, non-condensing
Patent information
Product is covered by one or more of the following patents: 4,910,794; 5,070,536; 5,295,154;
5,349,678; 5,394,436; 5,425,051; 5,428,636; 5,483,676; 5,504,746; 5,546,397; 5,574,979;
5,592,512; 5,680,633; 5,682,299; 5,696,903; 5,740,366; 5,790,536; 5,844,893; 5,862,171;
5,940,771; 5,960,344. There may be other U.S. and foreign patents pending.
™
6001 36th Avenue West
Everett, WA 98203
U.S.A.
www.intermec.com
© 2002 Intermec Technologies Corp.
All Rights Reserved
This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org).
This product includes cryptographic software written by Eric Young (ea[email protected]).
Government regulatory agencies require that this access point only use approved
antennas. Therefore, this access point uses a custom antenna connector. Do not
use antennas not approved for use with this access point.
Attention: Les organismes de réglementation gouvernementaux exigent que ce
point d’accès. Par conséquent, le point d’accès est doté d’un connecteur
d’antenne personnalisé. N’utilisez pas des antennes qui ne sont pas approuvées.
The WA21 without the internal power supply option is intended to be powered
only from an Ethernet host that complies with the IEEE 802.3af specification for
power over Ethernet (POE).
Attention: Le WA21 sans option de source d’alimentation interne est conçu pour
être alimenté à partir d’un hôte Ethernet qui est conforme à la spécification IEEE
802.3af pour l’alimentation par Ethernet (POE, de l’anglais Power Over Ethernet).
The WA21 with the internal power supply option may be connected either to a
standard Ethernet port or to a powered Ethernet host that complies with the IEEE
802.3af specification for power over Ethernet.
Attention: Le WA21 avec option de source d’alimentation interne peut être
connecté soit à un port Ethernet standard, soit à un hôte Ethernet alimenté qui
est conforme à la spécification IEEE 802.3af pour l’alimentation par Ethernet.
When the WA21 is connected to a powered Ethernet host, both the AC power
cord and the Ethernet cables must be disconnected prior to servicing.
Attention: Lorsque le WA21 est connecté à un hôte Ethernet alimenté, le cordon
d’alimentation CA et les câbles Ethernet doivent tous être débranchés avant tout
entretien ou dépannage.
CD
AC power
cord (optional)
Document
package
MobileLAN access
WA21
Defining the LEDs and Ports
MobileLAN
™
access WA21 Quick Start Guide
To access the WA21 ports, unscrew the two thumbscrews that are on the front of the cable
access door and then remove the door.
1
Mounting the WA21 Connecting the WA21
Attach antennas to the WA21. Intermec offers a variety of antennas and antenna
accessories. For a complete list, see the MobileLAN access System Manual.
Connect the WA21 to your network. You can either use an Ethernet cable to connect
the Ethernet port to an Ethernet drop or you can use the fiber optic port option. For
help connecting the WA21 to your fiber optic network, see “Connecting to Your Fiber
Optic Network” in the MobileLAN access System Manual.
Connect the WA21 to power. You can either use an AC power cord or power over
Ethernet. To use the power over Ethernet option, you use an Ethernet cable to
connect the Ethernet port to a MobileLAN power bridge or another 802.3af-
compliant power over Ethernet network. For help, see the documentation that
shipped with your power bridge.
3
5
4
Setting an Initial IP Address
Checking for Software Upgrades
You should check the Intermec MobileLAN Web site at http://mobilelan.intermec.com for
free software downloads and the latest documentation. To upgrade your access point
software, follow the instructions in the MobileLAN access System Manual.
You can place the WA21 either horizontally or vertically on a stable surface. You can also
mount the WA21 to a wall or a beam using one of these mounting bracket kits:
• Mounting bracket kit (P/N 068918)
• Rotating mounting bracket kit (P/N 068751)
Depending on your operating temperature needs and power, you can use these options:
1
3
2
3
Install the MobileLAN access Utility on your PC by inserting the enclosed CD,
clicking Install Software, and following the instructions that appear on your screen.
You can also download the software from http://mobilelan.intermec.com.
Note: Your PC must be on the same Ethernet segment as the access point.
Or, if your PC is communicating wirelessly with the access point, you must
have an active radio connection.
Start the utility.
Configure parameters A through C. See the screen to the right.
Click Set.
Reboot the access point by disconnecting it from and reconnecting it to a power
source. The Status box lets you know when the new IP address is successfully set.
1
5
4
3
2
Congratulations!
Your wireless end devices can now begin transmitting data packets through the WA21 to
your wired network. To continue configuring the access point, from the Actions menu
choose Configure Access Point. Your Web browser application (for example, Internet
Explorer) starts and the Access Point Login screen appears.
A
Click the down arrow and
choose Set IP Address.
B
Enter the Ethernet MAC
address of the access point
(printed on a label on the
access point).
C
Enter the new IP address of
the access point.
Click Software
Downloads.
Power
port
(optional)
Serial
port
Power
Remains on after
the WA21 boots.
Wireless #1
Flashes when a frame is
transmitted or received on
the radio port for the radio
installed in radio slot 1.
Wired LAN
Flashes when a
frame is transmitted
or received on the
Ethernet port.
Root/error
Flashes if this WA21 is
configured as the
root. It remains on if
an error is detected.
Wireless #2
Flashes when a frame is
transmitted or received on
the radio port for the radio
installed in radio slot 2 (if a
second radio is installed).
Fiber
optic port
(optional)
10BaseT/
100BaseTx
Ethernet port
Cable access
door
2
-25
º
C to 70
º
C
(-13
º
F to 158
º
F)
-30
º
C to 70
º
C
(-22
º
F to 158
º
F)
Use a mounting
bracket kit to
mount the WA21
with heater option
so that the LEDs
face down.
-30
º
C to 0
º
C
(-22
º
F to 32
º
F)
Place the WA21 with heater
option in an insulated bag
(P/N 068216) before using a
mounting bracket kit.
Wall
Wall
AC
power
Ethernet
connection
Antennas
-
1
-
2
Intermec MobileLAN access WA21 Guide de démarrage rapide
- Taper
- Guide de démarrage rapide
dans d''autres langues
Documents connexes
-
Intermec MobileLAN access WA21 Guide de démarrage rapide
-
Intermec MaxiScan 2100 Guide de démarrage rapide
-
Intermec MobileLAN access 2102 Guide de démarrage rapide
-
-
-
-
-
Intermec MobileLAN access WA22 Guide de démarrage rapide
-
-