STIHL MM 56 Manuel utilisateur

STIHL MM 56

Instruction Manual

Notice d’emploi

G Instruction Manual

1 - 23

F Notice d’emploi

24 - 48

Original Instruction ManualPrinted on chlorine-free paper

Printing inks contain vegetable oils, paper can be recycled.

0458-489-8221-A. VA1.L20.

0000008147_002_GB

MM 56 C

English

1

with electronic systems.

Contents

Dear Customer,

Thank you for choosing a quality

engineered STIHL product.

It has been built using modern

production techniques and

comprehensive quality assurance.

Every effort has been made to ensure

your satisfaction and trouble-free use of

the product.

Please contact your dealer or our sales

company if you have any queries

concerning this product.

Your

Dr. Nikolas Stihl

MultiSystem 2

Guide to Using this Manual 2

Safety Precautions and Working

Techniques 2

Approved MultiTools 7

Adjusting the bicycle handle 8

Fuel 8

Fueling 9

Starting / Stopping the Engine 10

Extra weight 12

Wheels 13

Operating Instructions 14

Replacing the Air Filter 14

Engine Management 15

Adjusting the Carburetor 15

Spark Plug 15

Engine Running Behavior 16

Storing the Machine 17

Maintenance and Care 18

Main Parts 19

Specifications 20

Maintenance and Repairs 20

Disposal 21

STIHL Limited Emission Control

Warranty Statement 21

MM 56 C

English

2

In the STIHL MultiSystem a number of

different MultiEngines and MultiTools

can be combined to produce a power

tool. In this instruction manual the

functional unit formed by the

MultiEngine and MultiTool is referred to

as the power tool.

Therefore, the separate instruction

manuals for the MultiEngine and

MultiTool should be used together for

the power tool.

Always read and and make sure you

understand both instruction manuals

before using your power tool for the first

time and keep them in a safe place for

future reference.

Pictograms

All the pictograms attached to the

machine are shown and explained in this

manual.

Symbols in text

WARNING

Warning where there is a risk of an

accident or personal injury or serious

damage to property.

NOTICE

Caution where there is a risk of

damaging the machine or its individual

components.

Engineering improvements

STIHL's philosophy is to continually

improve all of its products. For this

reason we may modify the design,

engineering and appearance of our

products periodically.

Therefore, some changes, modifications

and improvements may not be covered

in this manual.

Observe all applicable local safety

regulations, standards and ordinances.

If you have not used this type of power

tool before: Have your dealer or other

experienced user show you how it is

operated or attend a special course in its

operation.

Minors should never be allowed to use a

power tool.

Keep bystanders, especially children,

and animals away from the work area.

When the power tool is not in use, shut it

off so that it does not endanger others.

Secure it against unauthorized use.

The user is responsible for avoiding

injury to third parties or damage to their

property.

MultiSystem

+

0000-GXX-5900-A0

Guide to Using this Manual Safety Precautions and

Working Techniques

Special safety precau

-

tions must be observed

when working with a

power tool.

Always read and and

make sure you under

-

stand both instruction

manuals (MultiEngine

and MultiTool) before

using your power tool for

the first time and keep

them in a safe place for

future reference. Non-

observance of the safety

precautions may result in

serious or even fatal

injury.

MM 56 C

English

3

Lend or rent your power tool only to

persons who are familiar with this model

and its operation – do not lend of rent

your power tool without the MultiEngine

and MultiTool instruction manuals.

The use of noise emitting power tools

may be restricted to certain times by

national or local regulations.

To operate the power tool you must be

rested, in good physical condition and

mental health.

If you have any condition that might be

aggravated by strenuous work, check

with your doctor before operating a

power tool.

Persons with pacemakers only: The

ignition system of your power tool

produces an electromagnetic field of a

very low intensity. This field may

interfere with some pacemakers. STIHL

recommends that persons with

pacemakers consult their physician and

the pacemaker manufacturer to reduce

any health risk.

Do not operate the power tool if you are

under the influence of any substance

(drugs, alcohol) which might impair

vision, dexterity or judgment.

Use your power tool only for the

applications described in the instruction

manual of the MultiTool you are using.

Do not use your power tool for any other

purpose because of the increased risk of

accidents.

Do not operate the MultiEngine without a

properly mounted MultiTool since this

may result in damage to the machine.

Only use MultiTools and accessories

that are explicitly approved for this

power tool by STIHL or are technically

identical. It is important that you read the

chapter on "Approved MultiTools". If you

have any questions in this respect,

consult a servicing dealer. Use only high

quality tools and accessories in order to

avoid the risk of accidents and damage

to the machine.

STIHL recommends the use of genuine

STIHL tools and accessories. They are

specifically designed to match the

product and meet your performance

requirements.

Never attempt to modify your power tool

in any way since this may increase the

risk of personal injury. STIHL excludes

all liability for personal injury and

damage to property caused while using

unauthorized attachments.

Do not use a pressure washer to clean

your power tool. The solid jet of water

may damage parts of the power tool.

Clothing and Equipment

Wear proper protective clothing and

equipment.

Avoid clothing that could get caught on

branches or brush or moving parts of the

machine. Do not wear a scarf, necktie or

jewelry. Tie up and confine long hair

(e.g. with a hair net, cap, hard hat, etc.).

WARNING

Wear hearing protection, e.g. earplugs

or ear muffs.

Wear a face shield and make sure it is a

good fit. A face shield alone does not

provide adequate eye protection.

See also notes on "During Operation" in

the instruction manual of the MultiTool

you are using.

Vibrations

Prolonged use of the power tool may

result in vibration-induced circulation

problems in the hands (whitefinger

disease).

No general recommendation can be

given for the length of usage because it

depends on several factors.

The period of usage is prolonged by:

– Hand protection (wearing warm

gloves)

– Work breaks

The period of usage is shortened by:

– Any personal tendency to suffer

from poor circulation (symptoms:

frequently cold fingers, tingling

sensations).

– Low outside temperatures.

– The force with which the handles

are held (a tight grip restricts

circulation).

Your power tool produces

toxic exhaust fumes as

soon as the engine is

running. These fumes

may be colorless and

odorless and contain

unburned hydrocarbons

and benzol. Never run

the engine indoors or in

poorly ventilated loca

-

tions, even if your model

is equipped with a cata

-

lytic converter.

Keep your hands and feet

well away from the work

-

ing tool. To reduce the

risk of injury, never touch

a rotating tool. Always

stand behind the deflec

-

tor or to one side of the

machine during opera

-

tion – never in front of the

rotating tools.

MM 56 C

English

7

Continual and regular users should

monitor closely the condition of their

hands and fingers. If any of the above

symptoms appear (e.g. tingling

sensation in fingers), seek medical

advice.

Maintenance and Repairs

Service the machine regularly. Do not

attempt any maintenance or repair work

not described in the instruction manual.

Have all other work performed by a

servicing dealer.

STIHL recommends that you have

servicing and repair work carried out

exclusively by an authorized STIHL

servicing dealer. STIHL dealers are

regularly given the opportunity to attend

training courses and are supplied with

the necessary technical information.

Only use high-quality replacement parts

in order to avoid the risk of accidents

and damage to the machine. If you have

any questions in this respect, consult a

servicing dealer.

STIHL recommends the use of original

STIHL replacement parts. They are

specifically designed to match your

model and meet your performance

requirements.

To reduce the risk of injury, always shut

off the engine before carrying out any

maintenance or repairs or cleaning the

machine. – Exception: Carburetor and

idle speed adjustments.

Do not turn the engine over on the

starter with the spark plug boot or spark

plug removed unless the slide control /

stop switch is on STOP or 0 since there

is otherwise a risk of fire from

uncontained sparking.

To reduce the risk of fire, do not service

or store your machine near open flames.

Check the fuel filler cap for leaks at

regular intervals.

Use only a spark plug of the type

approved by STIHL and make sure it is

in good condition – see "Specifications".

Inspect the ignition lead (insulation in

good condition, secure connection).

Check the condition of the muffler.

To reduce the risk of fire and damage to

hearing, do not operate your machine if

the muffler is damaged or missing. –

Do not touch a hot muffler since burn

injury will result.

Maintenance, replacement, or repair of

the emission control devices and

systems may be performed by any

nonroad engine repair establishment or

individual. However, if you make a

warranty claim for a component which

has not been serviced or maintained

properly, STIHL may deny coverage.

For any maintenance please refer to the

maintenance chart and to the warranty

statement near the end of the instruction

manual.

The following STIHL MultiTools may be

mounted on the MultiEngine:

Approved MultiTools

MultiTool Application

BF

-

MM Pick tines

BK

-

MM Bolo tines

RL

-

MM Aerator

FC

-

MM Edger

FS

-

MM Clearing saw

MF

-

MM Dethatcher

KW

-

MM STIHL

PowerSweep

TM

KB

-

MM Bristle brush

9911BA000 KN

BF-MM

BK-MM

RL-MM

FC-MM

KB-MMKW-MM

MF-MM

FS-MM

MM 56 C

English

8

N Loosen the knob (1).

N Swing the bicycle handle with both

hands into the working position (as

far as stop).

N Tighten down the knob firmly.

This engine is certified to operate on

unleaded gasoline and with the mix ratio

50:1.

Your engine requires a mixture of high-

quality premium gasoline and high-

quality two-stroke air-cooled engine oil.

Use premium branded unleaded

gasoline with a minimum octane rating

of 89 (R+M)/2.

Note: Models equipped with a catalytic

converter require unleaded gasoline. A

few tankfuls of leaded gasoline can

reduce the efficiency of the catalytic

converter by more than 50%.

Fuel with a lower octane rating may

result in preignition (causing "pinging")

which is accompanied by an increase in

engine temperature. This, in turn,

increases the risk of the piston seizure

and damage to the engine.

The chemical composition of the fuel is

also important. Some fuel additives not

only detrimentally affect elastomers

(carburetor diaphragms, oil seals, fuel

lines etc.), but magnesium castings as

well. This could cause running problems

or even damage the engine. For this

reason it is essential that you use only

high-quality fuels!

Fuels with different percentages of

ethanol are being offered. Ethanol can

affect the running behaviour of the

engine and increase the risk of lean

seizure.

Gasoline with an ethanol content of

more than 10% can cause running

problems and major damage in engines

with a manually adjustable carburetor

and should not be used in such engines.

Engines equipped with M-Tronic can be

run on gasoline with an ethanol content

of up to 25% (E25).

Use only STIHL two-stroke engine oil or

equivalent high-quality two-stroke air-

cooled engine oils for mixing.

We recommend STIHL 50:1 two-stroke

engine oil since it is specially formulated

for use in STIHL engines.

To ensure the maximum performance of

your STIHL engine, use a high quality 2-

cycle engine oil. To help your engine run

cleaner and reduce harmful carbon

deposits, STIHL recommends using

STIHL HP Ultra 2-cycle engine oil or ask

your dealer for an equivalent fully

synthetic 2-cycle engine oil.

To meet the requirements of EPA and

CARB we recommend to use STIHL HP

Ultra oil.

Do not use BIA or TCW (two-stroke

water cooled) mix oils!

Use only STIHL 50:1 heavy-duty engine

oil or an equivalent quality two-stroke

engine oil for the fuel mix in models

equipped with a catalytic converter.

Take care when handling gasoline.

Avoid direct contact with the skin and

avoid inhaling fuel vapour.

The canister should be kept tightly

closed in order to avoid any moisture

getting into the mixture.

Adjusting the bicycle handle

0000-GXX-0549-A1

1

Fuel

MM 56 C

English

9

The fuel tank and the canister in which

fuel mix is stored should be cleaned

from time to time.

Fuel mix ratio

Only mix sufficient fuel for a few days

work, not to exceed 30 days of storage.

Store in approved safety fuel-canisters

only. When mixing, pour oil into the

canister first, and then add gasoline.

Dispose of empty mixing-oil canisters

only at authorized disposal locations.

Preparations

N Before fueling, clean the filler cap

and the area around it to ensure that

no dirt falls into the tank.

N Position the machine so that the

filler cap is facing up.

Opening screw-type tank cap

N Turn the cap counterclockwise until

it can be removed from the tank

opening.

N Remove the cap.

Filling up with fuel

Take care not to spill fuel while fueling

and do not overfill the tank. STIHL

recommends you use the STIHL filler

nozzle (special accessory).

Closing screw-type tank cap

N Place the cap in the opening.

N Turn the cap clockwise as far as

stop and tighten it down as firmly as

possible by hand.

Examples

Gasoline Oil (STIHL 50:1 or equiva

-

lent high-quality oils)

liters liters (ml)

10.02(20)

5 0.10 (100)

10 0.20 (200)

15 0.30 (300)

20 0.40 (400)

25 0.50 (500)

Fueling

547BA045 KN

002BA447 KN

002BA448 KN

MM 56 C

English

10

Controls

1 Throttle trigger lockout

2 Throttle trigger

3 Stop switch with Run and Stop

positions. Depress the stop switch

(…) to switch off the ignition – see

"Function of Stop Switch and

Ignition System".

Function of Stop Switch and Ignition

System

The ignition is switched off and the

engine stopped when the stop switch is

depressed. The stop switch returns

automatically to the Run position when it

is released: The ignition is switched on

again after the engine stops – the engine

is then ready to start.

Starting the Engine

N Swing bicycle handle into working

position – see "Adjusting the Bicycle

Handle"

N Depress the manual fuel pump

bulb (4) at least five times – even if

the bulb is filled with fuel.

Cold engine (cold start)

N Depress the choke knob (5) and

turn it to g at the same time.

Warm engine (warm start)

N Depress in the choke knob (5) and

turn it to < at the same time.

Also use this setting if the engine has

been running but is still cold.

Cranking

N Retract the wheels, if fitted.

N Put the unit on the ground: It must

rest securely on the engine flange

and the support on the frame.

Check that the MultiTool is not

touching the ground or any other

Starting / Stopping the

Engine

1

0000-GXX-0538-A0

2

3

0000-GXX-0540-A0

4

0000-GXX-0539-A0

5

0000-GXX-0541-A0

5

0000-GXX-0545-A0

MM 56 C

English

11

obstacles – see also "Starting /

Stopping the Engine" in the

MultiTool instruction manual.

N Make sure you have secure footing

– as shown. To reduce the risk of

injury from contact with rotating

attachments, always stand to the

side of the power tool.

N With your left hand on the carrying

handle, press the unit firmly against

the ground.

NOTICE

Do not stand or kneel on the shaft.

N Hold the starter grip with your right

hand.

Version without Easy2Start

N Pull the starter grip slowly until you

feel it engage and then give it a brisk

strong pull.

Version with Easy2Start

N Pull the starter grip steadily.

NOTICE

Do not pull out the starter rope all the

way – it might otherwise break.

N Do not let the starter grip snap back.

Guide it slowly back into the housing

so that the starter rope can rewind

properly.

N Continue cranking until the engine

runs.

As soon as the engine runs

N Press down the throttle trigger

lockout and open the throttle – the

choke lever moves to the run

position F. After a cold start, warm

up the engine by opening the

throttle several times.

WARNING

Make sure the carburetor is correctly

adjusted. The MultiTool must not rotate

when the engine is idling.

Your machine is now ready for

operation.

Stopping the Engine

N Depress the momentary contact

stop switch – the engine stops –

release the stop switch – it springs

back to the run position.

Other Hints on Starting

Engine stalls in cold start position g or

under acceleration.

N Move the choke knob to < and

continue cranking until the engine

runs.

Engine does not start in warm start

position <

N Move the choke knob to g and

continue cranking until the engine

runs.

If the engine does not start

N Check that all settings are correct.

N Check that there is fuel in the tank

and refuel if necessary.

N Check that the spark plug boot is

properly connected.

N Repeat the starting procedure.

Engine is flooded

N Move the choke knob to F and

continue cranking until the engine

runs.

0000-GXX-0546-A0

0000-GXX-0542-A0

MM 56 C

English

12

Fuel tank run until completely dry

N After refueling, depress the manual

fuel pump bulb at least five times –

even if the bulb is already filled with

fuel.

N Set the choke knob to suit the

engine temperature.

N Now start the engine.

An extra weight (special accessory) may

be retrofitted on the MultiEngine to

increase the weight on the MultiTool.

Use only original STIHL weights. The

use of other weights parts may result in

damage to the machine or personal

injury.

Mounting the extra weight

MultiEngine without wheels

Use the combination wrench to unscrew

and retighten the weights.

Unscrew weights on the side without

square end – as follows:

The weights (1) on the side with the

square end (2) remain on the bolt.

N Take out the hex head screw (3)

and remove the outer weight (4).

N Loosen the inner weight (5) and

remove it from the bolt.

N Push the extra weight (1) with bolt

through the bore (6) in the flange,

turning it until the square end (2)

engages the recess in the flange.

N Screw the inner weight (5) onto the

bolt and tighten it down firmly.

N Screw the outer weight (4) with the

hex head screw (3) into the thread

of the inner weight and tighten it

down firmly.

One of two weights may be mounted on

each side of the extra weight as

required.

NOTICE

The maximum allowable extra weight is

4 kg. Never use a heavier extra weight

as this may damage the machine.

MultiEngine with wheels

If the MultiEngine is already equipped

with wheels (special accessory), see

chapter on "Wheels", additional parts

are required to mount the extra weights.

In such a case have the extra weight

mounted by your servicing dealer.

Extra weight

469BA053 KN

1

2

3

4

5

Weight on each

side

Total extra weight

12kg

24kg

6

469BA054 KN

1

2

3

4

5

MM 56 C

English

13

STIHL recommends that you have

servicing and repair work carried out

exclusively by an authorized STIHL

servicing dealer.

For convenient transport, the

MultiEngine can be retrofitted with a set

of wheels (special accessory).

Always use original STIHL wheels.

Using other wheels can lead to damage

to the machine and personal injuries.

Installing wheels

No additional weight is attached to the

MultiEngine

To simplify installation, turn the machine

so that it rests on the handles.

N Insert the two sleeves (1) in the

frame

N Push the frame onto the flange

N Insert the bolt (2) with the

washer (3) through the hole (4) in

the flange

N Fit the washer (3) and tighten it

down with the nut (5)

N Fasten the notched plate (6) to the

frame with the screws (7) in the

threaded holes – in the process,

push the notched plate toward the

handle

N The wheels must fold down

automatically in working position; if

necessary, loosen the nut (5) by a

quarter turn

Additional weight is attached to the

MultiEngine

If additional weight (special accessory) –

see "Additional weight" – is already

attached to the MultiEngine, then

additional parts are required in order to

install wheels.

In this case, have the wheels installed by

a servicing dealer.

STIHL recommends that maintenance

and repair work be carried out only by

authorized STIHL dealers.

Folding the wheels in and out

The wheels can be locked in various

positions.

If the wheels are not needed during

work, fold in the wheels.

Wheels

3

6

469BA035 KN

2

4

1

7

5

3

1

MM 56 C

English

14

N Loosen knob (8)

N Engage knob in the desired working

position and tighten it

During break-in period

A factory-new machine should not be

run at high revs (full throttle off load) for

the first three tank fillings. This avoids

unnecessary high loads during the

break-in period. As all moving parts

have to bed in during the break-in

period, the frictional resistances in the

engine are greater during this period.

The engine develops its maximum

power after about 5 to 15 tank fillings.

During Operation

After a long period of full throttle

operation, allow the engine to run for a

short while at idle speed so that engine

heat can be dissipated by the flow of

cooling air. This protects engine-

mounted components (ignition,

carburetor) from thermal overload.

After Finishing Work

Storing for a short period: Wait for the

engine to cool down. Empty the fuel tank

and keep the machine in a dry place,

well away from sources of ignition, until

you need it again. For longer out-of-

service periods – see "Storing the

Machine".

If There is a Noticeable Loss of Engine

Power

N Move the choke lever (1) to <.

N Loosen the screws (2).

N Remove the filter cover (3).

N Clean away loose dirt from around

the filter.

N Remove the filter element (4).

N Replace dirty or damaged filter

element (4).

Replacing the filter element

N Install the filter element (4) in the

filter housing (5) and fit the cover.

N Insert the screws (2) and tighten

them down firmly.

8

469BA036 KN

Operating Instructions Replacing the Air Filter

0000-GXX-0543-A0

1

2

3

4

5

MM 56 C

English

15

Exhaust emissions are controlled by the

design of the engine and components

(e.g. carburation, ignition, timing and

valve or port timing).

The carburetor has been set at the

factory to provide an optimum fuel-air

mixture under most operating

conditions.

Adjusting Idle Speed

Engine stops while idling

N Warm up the engine for about

3 minutes.

N Turn the idle speed screw (LA)

slowly clockwise until the engine

runs smoothly – the MultiTool must

not run.

MultiTool runs when the engine is idling

N Turn the idle speed screw (LA)

counterclockwise until the MultiTool

stops moving and then turn the

screw about another 1/2 to 3/4 turn

in the same direction.

WARNING

If the MultiTool continues to run when

the engine is idling, have your machine

checked and repaired by your servicing

dealer.

N If the engine is down on power,

difficult to start or runs poorly at idle

speed, first check the spark plug.

N Fit a new spark plug after about 100

operating hours – or sooner if the

electrodes are badly eroded. Install

only suppressed spark plugs of the

type approved by STIHL – see

"Specifications".

Removing the Spark Plug

N Shut off the engine.

The spark plug boot (2) is under the

cap (1).

WARNING

The cap (1) protects the spark plug boot

from damage. Do not operate the

machine without a cap – replace a

damaged cap.

N Remove the cap (1).

N Pull off the spark plug boot (2).

N Allow the spark plug (3) to cool

down.

N Unscrew the spark plug (3).

Engine Management Adjusting the Carburetor

0000-GXX-0544-A0

Spark Plug

3

1

4907BA014 KN

MM 56 C

English

16

Checking the Spark Plug

N Clean dirty spark plug.

N Check electrode gap (A) and

readjust if necessary – see

"Specifications".

N Rectify the problems which have

caused fouling of the spark plug.

Possible causes are:

– Too much oil in fuel mix.

– Dirty air filter.

– Unfavorable running conditions.

WARNING

Arcing may occur if the adapter nut (1) is

loose or missing. Working in an easily

combustible or explosive atmosphere

may cause a fire or an explosion. This

can result result in serious injuries or

damage to property.

N Use resistor type spark plugs with a

properly tightened adapter nut.

Installing the spark plug

N Screw the spark plug into the

cylinder.

N Press the boot firmly onto the spark

plug.

N Push the cap (1) on to the spark

plug boot as far as stop.

If engine running behavior is

unsatisfactory even though the air filter

is clean and the carburetor is properly

adjusted, the cause may be the muffler.

Have the muffler checked for

contamination (carbonization) by your

servicing dealer.

STIHL recommends that you have

servicing and repair work carried out

exclusively by an authorized STIHL

servicing dealer.

000BA039 KN

A

1

000BA045 KN

4907BA016 KN

1

Engine Running Behavior

MM 56 C

English

17

For periods of about 3 months or longer

N Drain and clean the fuel tank in a

well ventilated area.

N Dispose of fuel properly in

accordance with local

environmental requirements.

N Run the engine until the carburetor

is dry – this helps prevent the

carburetor diaphragms sticking

together.

N Thoroughly clean the machine – pay

special attention to the cylinder fins

and air filter.

N Remove, clean and inspect the

attachment.

N Store the machine in a dry and

secure location Keep out of the

reach of children and other

unauthorized persons.

Fold the handle down and hang up the

machine by the handle support.

Storing the Machine

0000-GXX-0551-A0

MM 56 C

English

18

Maintenance and Care

The following intervals apply to normal operating conditions only. If your daily work

-

ing time is longer or operating conditions are difficult (very dusty work area, etc.),

shorten the specified intervals accordingly.

before starting work

after finishing work or daily

after each refueling stop

weekly

monthly

every 12 months

if problem

if damaged

as required

Complete machine

Visual inspection (condition, leaks) X X

Clean X

Control handle Check operation XX

Air filter

Clean XX

Replace X

Manual fuel pump (if fitted)

Check X

Have repaired by servicing dealer

1)

X

Pickup body (filter) in fuel tank

Check X

Have replaced by servicing dealer

1)

XXX

Fuel tank Clean XX

Carburetor

Check idle adjustment – the working/cut

-

ting attachment must not run

XX

Readjust idle X

Spark plug

Readjust electrode gap X

Replace after every 100 operating hours

Cooling inlet

Visual inspection X

Clean X

Spark arrestor in muffler

Check XX

Clean or replace XX

All accessible screws and nuts (not adjust

-

ing screws)

Retighten X

Safety labels Replace X

1)

STIHL recommends an authorized STIHL servicing dealer.

La page charge ...

STIHL MM 56 Manuel utilisateur

STIHL MM 56 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents