{
STIHL MF-MM
Instruction Manual
Notice d’emploi
Original Instruction ManualPrinted on chlorine-free paper
Printing inks contain vegetable oils, paper can be recycled.
© ANDREAS STIHL AG & Co. KG, 2015
0458-483-8221. VA0.L15.
0000000635_005_GB
MF-MM
English
1
{
This instruction manual is protected by copyright. All rights reserved, especially the rights to reproduce, translate and process
with electronic systems.
Contents
Dear Customer,
Thank you for choosing a quality
engineered STIHL product.
It has been built using modern
production techniques and
comprehensive quality assurance.
Every effort has been made to ensure
your satisfaction and troublefree use of
the product.
Please contact your dealer or our sales
company if you have any queries
concerning this product.
Your
Dr. Nikolas Stihl
MultiSystem 2
Guide to Using this Manual 2
Safety Precautions and Working
Techniques 2
Using the Unit 6
Approved MultiEngines 7
Mounting the MultiTool 7
Mounting the Deflector 10
Starting / Stopping the Engine 10
Replacing Spring Tines 11
Storing the Machine 11
Maintenance and Care 12
Main Parts 13
Specifications 14
Maintenance and Repairs 14
Disposal 15
MF-MM
English
2
In the STIHL MultiSystem, various
MultiEngines and MultiTools are
combined to form a machine. In this
Instruction Manual, the functional unit of
MultiEngine and MultiTool is referred to
as a machine.
Accordingly, the instruction manuals for
the MultiEngine and the MultiTool
constitute the entire Instruction Manual
for the machine.
Always read both manuals carefully
before using your machine for the first
time and keep them safe for future
reference.
Pictograms
All the pictograms attached to the
machine are shown and explained in this
manual.
Symbols in text
WARNING
Warning where there is a risk of an
accident or personal injury or serious
damage to property.
NOTICE
Caution where there is a risk of
damaging the machine or its individual
components.
Engineering improvements
STIHL's philosophy is to continually
improve all of its products. For this
reason we may modify the design,
engineering and appearance of our
products periodically.
Therefore, some changes, modifications
and improvements may not be covered
in this manual.
Lend or rent your power tool only to
persons who are familiar with this model
and its operation – do not lend of rent
your power tool without the MultiEngine
and MultiTool instruction manuals.
Use the dethatcher only for removing
old, dried cuttings, moss, grass or root
residue from lawns.
Do not use your power tool for any other
purpose because of the increased risk of
accidents.
Only use attachments and accessories
that are explicitly approved for this
power tool model by STIHL or are
technically identical. If you have any
questions in this respect, consult a
servicing dealer.
MultiSystem
469BA028 KN
+
+
Guide to Using this Manual Safety Precautions and
Working Techniques
Some special safety pre-
cautions must be
observed to reduce the
risk of personal injury
when operating the
dethatcher because of
the high speed of its
rotating tines.
Always read and and
make sure you under-
stand both instruction
manuals (MultiEngine
and MultiTool) before
using your power tool for
the first time and keep
them in a safe place for
future reference. Non-
observance of the safety
precautions may result in
serious or even fatal
injury.
MF-MM
English
3
Use only high quality parts and
accessories in order to avoid the risk of
accidents and damage to the machine.
STIHL recommends the use of original
STIHL replacement parts. They are
specifically designed to match the
product and meet your performance
requirements.
The deflector on this power tool cannot
protect the operator from all objects
thrown by the attachment (stones, glass,
wire, etc.). Such objects may ricochet
and then hit the operator.
Never attempt to modify your unit in any
way since this may increase the risk of
personal injury. STIHL excludes all
liability for personal injury and damage
to property caused while using
unauthorized attachments.
Do not use a pressure washer to clean
the unit. The solid jet of water may
damage parts of the unit.
Clothing and Equipment
Wear proper protective clothing and
equipment.
Avoid clothing that could get caught on
branches or brush or moving parts of the
machine. Do not wear a scarf, necktie or
jewelry. Tie up and confine long hair
(e.g. with a hair net, cap, hard hat, etc.).
WARNING
Wear hearing protection, e.g. earplugs
or ear muffs.
STIHL offers a comprehensive range of
personal protective clothing and
equipment.
Transporting the Power Tool
Always turn off the engine.
Carry your power tool by the handle,
attachment in front of you.
Do not touch hot parts of the machine
since burn injury will result.
In vehicles: Properly secure your power
tool to prevent turnover, fuel spillage and
damage.
The power tool may be dragged
backwards (opposite to normal direction
of operation) for short distances. Never
attempt to move it around by pushing it
forwards as this could result in damage.
The spring tines might break.
Before Starting
Check that your power tool is properly
assembled and in good condition – refer
to appropriate chapters in the
MultiEngine and MultiTool instruction
manuals.
– Attachment correctly and securely
mounted and in good condition
(clean, move freely, not warped).
– Mount both deflector extensions
and mud flap.
– Inspect the deflectors for damage
and wear. Do not operate the
machine with a damaged deflector –
replace damaged parts.
– Never attempt to modify the controls
or safety devices in any way.
– Keep the handles dry and clean –
free from oil and dirt – for safe
control of the power tool.
– Swing the handlebar to the normal
operating position and tighten it
down firmly with the rotary knob.
See chapter on "Adjusting the
Handlebar" in the MultiEngine
instruction manual.
Clothing must be sturdy
but allow complete free-
dom of movement. Wear
snug-fitting clothing, an
overall and jacket combi-
nation, do not wear a
work coat.
Wear sturdy shoes with
non-slip soles.
To reduce the risk of eye
injuries, wear snug-fitting
safety glasses in accord-
ance with European
Standard EN 166. Make
sure the safety glasses
are a good fit.
Wear heavy-duty work
gloves made of durable
material (e.g. leather).
469BA001 KN
MF-MM
English
4
To reduce the risk of accidents, do not
operate your power tool if it is damaged
or not properly assembled.
Check correct position of gearbox and
adjust if necessary. This helps reduce
the risk of injury from the MultiTool
rotating in the wrong direction.
See also notes on "Mounting the
MultiTool".
If you use metal tools, position the
gearbox so that the axle is below the
drive shaft.
Use this position for:
– BF-MM pick tines
– BK-MM bolo tines
– FC-MM edger
– RL-MM aerator
– MF-MM dethatcher
Holding and Controlling the Unit
Make sure you always have good
balance and secure footing.
Always hold the power tool firmly with
both hands on the handles.
Right handle on control handle, left hand
on left handle.
During Operation
In the event of impending danger or in
an emergency, switch off the engine
immediately by moving the slide control
/ stop switch/button to 0 or STOP.
To reduce the risk of injury from contact
with the tool and thrown objects, do not
allow any other persons within a radius
of 5 meters of your own position. To
reduce the risk of damage to property,
also maintain this distance from other
objects (vehicles, windows).
The correct engine idle speed is
important to ensure that the attachment
stops moving when you let go of the
throttle trigger. Check and correct the
idle speed setting regularly. If the
attachment still rotates when the engine
is idling, have your dealer check your
machine and make proper adjustments
or repairs – see MultiEngine instruction
manual.
To reduce the risk of injury from thrown
objects or contact with the attachment,
never operate the unit without a properly
mounted deflector designed specifically
for the unit and the attachment.
Always stand behind the deflector or to
one side of the machine during
operation – never in front of the
attachment.
Do not push the attachment into the
ground.
Take special care in slippery conditions
– damp or ice on slopes or uneven
ground.
To reduce the risk of accidents or injury,
remove all obstacles and objects from
the work area.
Inspect the work area – solid objects
(stones, pieces of metal, etc.) may
damage the attachment.
469BA045 KN
5m (16ft)
The gearbox becomes
hot during operation. To
reduce the risk of burn
injury, do not touch the
gearbox housing.
To avoid the risk of elec-
tric shock, never use your
power tool in areas where
electrical lines are laid on
the surface or buried just
below the surface. Strik-
ing and damaging such
lines with the attachment
could cause serious or
even fatal injury.
MF-MM
English
5
Operate your power tool at normal
walking pace only.
Be extremely cautious when pulling the
power tool towards you because of the
risk of injury from contact with the
rotating attachment.
Make sure you always have good
balance and secure footing.
Be extremely cautious when changing
direction with the power tool – especially
on slopes.
On slopes, always work parallel to the
gradient to reduce the risk of injury from
slipping or contact with the attachment.
Never work on steep slopes because of
the risk of injury through loss of control
of the power tool.
Take particular care when working close
to fences, walls, stones, roots, trees and
areas of dense growth. Solid objects
may be thrown in your direction or
damage the attachment – risk of
accidents.
When working next to high scrub,
bushes and hedges, take care not to
harm small animals.
Be particularly alert and cautious when
wearing hearing protection because
your ability to hear warnings (shouts,
alarms, etc.) is restricted.
To reduce the risk of accidents, take a
break in good time to avoid tiredness or
exhaustion.
Work calmly and carefully – in daylight
conditions and only when visibility is
good. Stay alert so as not to endanger
others.
If your power tool is subjected to
unusually high loads for which it was not
designed (e.g. heavy impact or a fall),
always check that it is in good condition
before continuing work – see also
"Before Starting". Make sure the safety
devices are working properly. Do not
continue operating your power tool if it is
damaged. In case of doubt, have the unit
checked by your servicing dealer.
Do not touch the attachment while the
engine is running. If the attachment
becomes jammed by an obstruction,
switch off the engine immediately before
attempting to remove the obstruction.
Opening the throttle while the
attachment is blocked increases the
load and reduces engine speed. The
clutch then slips continuously and this
causes overheating and damage to
important components (e.g. clutch,
polymer housing components) – and this
can increase the risk of injury from the
cutting attachment moving while the
engine is idling.
Check the attachment at regular short
intervals during operation or
immediately if there is a noticeable
change in behavior:
– Shut off the engine, hold the unit
securely.
– Check condition and tightness, look
for broken spring tines.
– Replace damaged spring tines
immediately.
Clean the attachment and deflector at
regular intervals during operation.
–
Shut off the engine.
– Wear gloves.
– Remove grass, weeds and scrub,
etc.
To reduce the risk of injury, shut off the
engine before changing attachments.
Never continue using or attempt to
repair damaged or cracked spring tines.
After Finishing Work
After finishing work or before leaving the
unit unattended: Shut off the engine.
After finishing work, clean dirt, soil and
plant residue off the attachment – wear
gloves to reduce the risk of injury.
Do not use grease solvents for cleaning.
After thoroughly cleaning, coat metal
surface of attachments with a corrosion
inhibitor.
Maintenance and Repairs
Service the machine regularly. Do not
attempt any maintenance or repair work
not described in the MultiTool and
MultiEngine instruction manuals. Have
all other work performed by a servicing
dealer.
STIHL recommends that you have
servicing and repair work carried out
exclusively by an authorized STIHL
servicing dealer. STIHL dealers are
regularly given the opportunity to attend
training courses and are supplied with
the necessary technical information.
MF-MM
English
6
Only use high-quality replacement parts
in order to avoid the risk of accidents
and damage to the power tool. If you
have any questions in this respect,
consult a servicing dealer.
STIHL recommends the use of original
STIHL replacement parts. They are
specifically designed to match your
model and meet your performance
requirements.
To reduce the risk of injury, always shut
off the engine before carrying out any
maintenance or repairs or cleaning the
machine.
The MF-MM dethatcher MultiTool is
designed to remove old, dried cuttings,
moss, grass or root residue from lawns.
Preparations
If the lawn is very dry, spray it with water
before you start work: this softens the
soil a little and reduces the amount of
dust created.
If the grass is longer than about 5 cm,
mow it before using the dethatcher.
WARNING
Clear away all obstacles and solid
objects from the work area.
N Plan the route to be taken.
Operate the MultiEngine with MF-MM
dethatcher in the forward direction only.
The attachments may only be rotate in
one direction. Arrows on the flanges
show the correct direction of rotation –
see chapter on "Mounting the MultiTool".
WARNING
Never work without the deflector, both
deflector extensions and the mud flap.
These devices divert loosened and cut
material away from the machine and the
operator.
Using the Unit
483BA001 KN
483BA002 KN
483BA003 KN
MF-MM
English
7
Operation
N Secure the handlebar in the normal
operating position.
N Start the engine.
N Work with the engine running at full
throttle.
N Walk at a pace that achieves the
required result without lugging down
the engine.
N Operate at no more than a normal
walking pace.
Cleaning the Dethatcher
Parts of plants, such as grass or roots,
may become tightly wound around the
tool mounting and the attachment itself.
Clean the attachment as follows:
– Shut off the engine.
– Wear work gloves.
– Remove the inner hitch pins from
the shaft.
– Pull the dethatcher off the shaft.
– Remove the outer hitch pin (wheel)
from the shaft.
– Pull off the wheel.
– Remove pieces of roots, plants and
soil.
Refer to "Mounting the MultiTool" for
mounting instructions.
Only use MultiEngines supplied by
STIHL or expressly approved by STIHL
for use with the MultiTool.
This MultiTool may only be used in
combination with the STIHL MM 55
MultiEngine.
Removing Existing MultiTools
WARNING
Wear gloves to reduce the risk of injury
from contact with sharp MultiTools
and/or hot surface of gearbox.
N Remove the hitch pins and pull the
MultiTools (if fitted) off the axle –
see also "Mounting the MultiTool" in
the instruction manual of the other
MultiTool.
N Clean the gearbox if necessary.
Approved MultiEngines Mounting the MultiTool
481BA008 KN
MF-MM
English
8
Checking Deflector
WARNING
To reduce the risk of injury from thrown
objects, operate the MF-MM dethatcher
only with the deflector shown and with
properly mounted deflector extensions.
Changing the Deflector
Removing the Gearbox
N Loosen the clamp screws (1) and
pull the gearbox (2) off the drive
tube.
Removing the Deflector
N Loosen the screw (3) and pull the
deflector (4) off the drive tube.
Fitting New Deflector
N Line up the deflector (5) on the
flange (6) and push it onto the drive
tube as far as stop.
N Tighten down the clamp screws (7)
firmly.
Mounting the Gearbox
N Push the gearbox (2) onto the drive
tube as far as stop while turning it
back and forth.
N Line up the gearbox.
N Go to "Checking Position of
Gearbox".
486BA011 KN
1
486BA012 KN
2
1
3
486BA013 KN
4
7
7
5
486BA014 KN
6
1
1
2
486BA015 KN
MF-MM
English
9
Checking Position of Gearbox
WARNING
To reduce risk of injury from the
MultiTool rotating in the wrong direction,
check that position of gearbox is correct
and adjust if necessary.
The axle (1) must be below the shaft (2).
Direction of rotation (3) of MultiTool.
Adjusting Position of Gearbox
N Loosen clamp screws on gearbox.
N Turn the gearbox through 180°.
N Line up the gearbox in the correct
position.
N Tighten down the two clamp screws
on the gearbox in the following
sequence:
– Tighten the first screw moderately.
– Tighten the second screw
moderately.
– Tighten down first screw firmly.
– Tighten down second screw firmly.
NOTICE
It must not be possible to rotate the
gearbox on the drive tube.
Mounting the Dethatcher
NOTICE
Left-hand and right-hand dethatchers
are different.
The direction of rotation is marked with
arrows on the gearbox and flange. Make
sure both arrows point in the same
direction.
The spring tines may be damaged or
break if the direction of rotation is wrong.
N Rotate the left-hand dethatcher (4)
on the shaft until it can be pushed
into position – check the direction of
rotation again (arrows).
N Insert hitch pin (5) in hole in shaft
and snap it into position.
N Mount the right-hand dethatcher in
the same way.
WARNING
Always mount both dethatchers.
481BA011 KN
4
483BA004 KN
5
MF-MM
English
10
Mounting and Removing the Deflector
Extensions
Mounting
N Slide both deflector extensions onto
the right and left sides of the
deflector, push them fully home at
the top and bottom and engage the
tab (1).
Removing
N Use the combination wrench to
disengage the tabs (1) and then pull
off the extensions.
WARNING
The deflector extensions divert removed
material and debris away from the
machine and the operator. Never work
without a properly mounted deflector
extensions.
Installing and Removing the Mud Flap
N Secure the mud flap (1) with
screw (2) and rotary knob (3) to the
right-hand side of the flange.
N Adjust the mud flap to the required
length so that it overlaps the
deflector.
N Tighten down the rotary knob firmly.
WARNING
The mud flap diverts removed material
and debris away from the machine and
the operator. Never work without a
properly mounted mud flap.
Starting the Engine
Always follow the starting procedure
described in the MultiEngine instruction
manual.
N Secure the handlebar in the normal
operating position.
N Retract the wheels, if fitted – see
chapter on "Wheels" in MultiEngine
instruction manual.
N Retract the spur, if fitted.
Mounting the Deflector
1
1
483BA007 KN
3
483BA011 KN
2
Starting / Stopping the
Engine
469BA061 AS
469BA062 AS
MF-MM
English
11
N Check that the MultiTool is not
touching the ground or any other
obstacles. The unit must rest on the
engine flange and the support on
the frame.
N Make sure you have good balance
and secure footing – as shown in the
illustration.
WARNING
To reduce the risk of injury from contact
with the rotating attachment, always
stand to the side of the power tool, never
in front of the attachment.
N With your left hand on the loop
handle, press the unit firmly against
the ground – do not touch the
throttle trigger or lockout lever.
NOTICE
Do not stand or kneel on the handlebar
or frame.
WARNING
The attachment may begin to move as
soon as the engine starts. For this
reason, blip the throttle after starting –
the engine returns to idling speed.
Now follow the starting procedure
described in the MultiEngine instruction
manual.
Stopping the Engine
N See MultiEngine instruction manual.
Replace individual spring tines if they
are severely damaged or broken.
N Remove the dethatcher – see
"Mounting the MultiTool".
N Loosen the screws (1) on the
dethatcher.
N Remove the flange (2).
Spring tines and washers are fitted
alternately on the tubes.
N Pull off the spring tines (3) and
washers.
N Replace damaged spring tines.
N Fit spring tines and washers on the
tubes until they are full.
N Fit the flange (2).
N Tighten down the screws (1) firmly.
N Mount the dethatcher – see
"Mounting the MultiTool".
For periods of 3 months or longer
N Remove, clean and inspect the
dethatcher with deflector extensions
and mud flap.
N Store the machine in a dry, high or
locked location – out of the reach of
children and other unauthorized
persons.
Replacing Spring Tines
483BA006 KN
1
2
3
1
Storing the Machine
MF-MM
English
12
The following intervals apply to normal
operating conditions only. If your daily
working time is longer or operating
conditions are difficult (very dusty work
area, etc.), shorten the specified
intervals accordingly.
All accessible screws and nuts
N Retighten if necessary
Sweeping attachments and deflectors
N Visual inspection, check tightness
before starting work and after every
refueling stop
N Replace if damaged
Safety labels
N Replace illegible safety labels
Maintenance and Care
MF-MM
English
13
1 Right-hand Wheel
2 Left-hand Wheel
3 Inner Hitch Pin
4 Deflector Extension, Right
5 Deflector Extension, Left
6 Skirt
7 Outer Hitch Pin
8 Spring Tines
9 Deflector
Main Parts
1
483BA012 KN
8
3
2
6
5
4
7
99
MF-MM
English
14
Definitions
1 Right-hand Wheel
Keeps the spring tines of the
dethatcher at a constant height
above the ground.
2 Left-hand Wheel
Keeps the spring tines of the
dethatcher at a constant height
above the ground.
3 Inner Hitch Pin
Secures the attachment to the shaft
and simplifies installation and
removal of the attachment.
4 Deflector Extension, Right
Helps divert removed material and
debris away from the machine and
operator.
5 Deflector Extension, Left
Helps divert removed material and
debris away from the machine and
operator.
6Skirt
Diverts removed material and
debris away from the machine and
operator.
7 Outer Hitch Pin
Secures the wheel to the
attachment and simplifies
installation and removal of the
wheel.
8 Spring Tines
Elements of attachment for
removing moss, dead grass and
root residue from lawns.
9 Deflector
Large deflector for attaching
deflector extensions.
Attachment
Weight
Users of this machine may only carry out
the maintenance and service work
described in this user manual. All other
repairs must be carried out by a
servicing dealer.
STIHL recommends that you have
servicing and repair work carried out
exclusively by an authorized STIHL
servicing dealer. STIHL dealers are
regularly given the opportunity to attend
training courses and are supplied with
the necessary technical information.
When repairing the machine, only use
replacement parts which have been
approved by STIHL for this power tool or
are technically identical. Only use high-
quality replacement parts in order to
avoid the risk of accidents and damage
to the machine.
STIHL recommends the use of original
STIHL replacement parts.
Original STIHL parts can be identified by
the STIHL part number, the {
logo and the STIHL parts symbol K
(the symbol may appear alone on small
parts).
Specifications
Dethatcher, left, right
Working width: 500 mm
Dethatcher with deflec-
tor extensions and mud
flap 8.6 kg
Maintenance and Repairs
MF-MM
English
15
Observe all country-specific waste
disposal rules and regulations.
STIHL products must not be thrown in
the garbage can. Take the product,
accessories and packaging to an
approved disposal site for environment-
friendly recycling.
Contact your STIHL servicing dealer for
the latest information on waste disposal.
Disposal
000BA073 KN
Notice d'emploi d'origine Imprimé sur papier blanchi sans chlore
L'encre d'imprimerie contient des huiles végétales, le papier
est recyclable.
© ANDREAS STIHL AG & Co. KG, 2015
0458-483-8221. VA0.L15.
0000000635_005_F
MF-MM
français
16
{
La présente Notice d'emploi est protégée par des droits d'auteur. Tous droits réservés, en particulier tout droit de copie, de tra-
duction et de traitement avec des systèmes électroniques quelconques.
Table des matières
Chère cliente, cher client,
nous vous félicitons d'avoir choisi un
produit de qualité de la société STIHL.
Ce produit a été fabriqué avec les
procédés les plus modernes et les
méthodes de surveillance de qualité les
plus avancées. Nous mettons tout en
œuvre pour que cette machine vous
assure les meilleurs services, de telle
sorte que vous puissiez en être
parfaitement satisfait.
Pour toute question concernant cette
machine, veuillez vous adresser à votre
revendeur ou directement à
l'importateur de votre pays.
Dr. Nikolas Stihl
MultiSystème 17
Indications concernant la présente
Notice d'emploi 17
Prescriptions de sécurité et
techniques de travail 17
Utilisation 22
Moteurs MultiSystème autorisés 23
Montage de l'outil MultiSystème 23
Montage des dispositifs de sécurité 26
Mise en route / arrêt du moteur 26
Remplacement des dents à ressort 27
Rangement 27
Instructions pour la maintenance et
l'entretien 28
Principales pièces 29
Caractéristiques techniques 30
Instructions pour les réparations 31
Mise au rebut 31
MF-MM
français
17
Le MultiSystème STIHL offre la
possibilité de combiner différents
moteurs MultiSystème et outils
MultiSystème pour composer une
machine. Dans la présente Notice
d'emploi, l'ensemble – en ordre de
marche – d'un moteur MultiSystème et
d'un outil MultiSystème est dénommé
machine ou dispositif à moteur.
Par conséquent, les Notices d'emploi du
moteur MultiSystème et de l'outil
MultiSystème constituent, ensemble, la
Notice d'emploi intégrale de la machine
ou du dispositif à moteur.
Il faut donc toujours lire attentivement
les deux Notices d'emploi avant la
première mise en service de la machine
et les conserver précieusement pour
pouvoir les relire lors d'une utilisation
ultérieure.
Pictogrammes
Tous les pictogrammes appliqués sur le
dispositif sont expliqués dans la
présente Notice d'emploi.
Repérage des différents types de textes
AVERTISSEMENT
Avertissement contre un risque
d'accident et de blessure ainsi que de
graves dégâts matériels.
AVIS
Avertissement contre un risque de
détérioration du dispositif ou de certains
composants.
Développement technique
La philosophie de STIHL consiste à
poursuivre le développement continu de
toutes ses machines et de tous ses
dispositifs ; c'est pourquoi nous devons
nous réserver tout droit de modification
de nos produits, en ce qui concerne la
forme, la technique et les équipements.
On ne pourra donc en aucun cas se
prévaloir des indications et illustrations
de la présente Notice d'emploi à l'appui
de revendications quelconques.
Ne confier la machine qu'à des
personnes familiarisées avec ce modèle
et sa manipulation – et toujours y joindre
les Notices d'emploi du moteur
MultiSystème et de l'outil MultiSystème.
Utiliser le démousseur exclusivement
pour extraire des pelouses les restes
d'herbe coupée desséchés, ainsi que la
mousse et les morceaux d'herbe ou de
racines détachés.
Il est interdit d'utiliser cette machine
pour d'autres travaux – risque
d'accident !
Monter exclusivement des outils de
travail ou accessoires autorisés par
STIHL pour cette machine, ou des
pièces similaires du point de vue
MultiSystème
469BA028 KN
+
+
Indications concernant la
présente Notice d'emploi
Prescriptions de sécurité et
techniques de travail
En travaillant avec le
démousseur, il faut res-
pecter des prescriptions
de sécurité particulières,
parce que l'outil de travail
tourne à haute vitesse.
Avant la première mise
en service, lire attentive-
ment et intégralement les
deux Notices d'emploi
(celle du moteur
MultiSystème et celle de
l'outil MultiSystème). Les
conserver précieuse-
ment pour pouvoir les
relire lors d'une utilisa-
tion ultérieure. Le fait de
ne pas respecter les ins-
tructions des Notices
d'emploi peut entraîner
un danger de mort.
MF-MM
français
18
technique. Pour toute question à ce
sujet, s'adresser à un revendeur
spécialisé.
Utiliser exclusivement des outils ou
accessoires de haute qualité. Sinon, des
accidents pourraient survenir ou la
machine risquerait d'être endommagée.
STIHL recommande d'utiliser des outils
et accessoires d'origine STIHL. Leurs
caractéristiques sont optimisées tout
spécialement pour ce produit, et pour
satisfaire aux exigences de l'utilisateur.
Le capot protecteur de l'outil de travail
ne peut pas protéger l'utilisateur contre
tous les objets (pierres, morceaux de
verre ou de fil de fer etc.) projetés par
l'outil de travail. Ces objets peuvent
ricocher et toucher l'utilisateur.
N'apporter aucune modification à cette
machine – cela risquerait d'en
compromettre la sécurité. STIHL décline
toute responsabilité pour des blessures
ou des dégâts matériels occasionnés en
cas d'utilisation d'outils de travail non
autorisés.
Pour le nettoyage de cette machine, ne
pas utiliser un nettoyeur haute pression.
Le puissant jet d'eau risquerait
d'endommager certaines pièces de la
machine.
Vêtements et équipement
Porter des vêtements et équipements de
protection réglementaires.
Ne pas porter des vêtements qui
risqueraient de se prendre dans le bois,
les broussailles ou les pièces en
mouvement de la machine. Ne porter ni
écharpe ou cravate, ni bijoux. Les
personnes aux cheveux longs doivent
les nouer et les assurer (foulard,
casquette, casque etc.).
AVERTISSEMENT
Porter un dispositif antibruit
« individuel » – par ex. des capsules
protège-oreilles.
STIHL propose une gamme complète
d'équipements pour la protection
individuelle.
Transport
Toujours arrêter le moteur.
Porter la machine par la poignée de
portage, avec l'outil de travail en avant.
Ne pas toucher aux pièces très chaudes
de la machine – risque de brûlure !
Pour le transport dans un véhicule :
assurer la machine de telle sorte qu'elle
ne risque pas de se renverser, d'être
endommagée ou de perdre du
carburant.
Pour parcourir de courtes distances, il
est également permis de tirer la machine
dans le sens contraire au sens de
travail. Pour transporter la machine, ne
jamais la pousser dans le sens de travail
– risque d'endommagement ! Les dents
à ressort risqueraient de casser.
Les vêtements doivent
être fonctionnels et
garantir une liberté de
mouvement totale. Por-
ter des vêtements bien
ajustés – une combinai-
son, mais pas une blouse
de travail.
Porter des chaussures
robustes avec semelle
crantée antidérapante.
Étant donné le risque de
blessure des yeux, il faut
impérativement porter
des lunettes de protec-
tion couvrant étroitement
les yeux, conformément
à la norme EN 166. Veil-
ler à ce que les lunettes
soient parfaitement
ajustées.
Porter des gants de tra-
vail robustes (par ex. en
cuir).
469BA001 KN
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
dans d''autres langues
- English: STIHL MF-MM User manual
Documents connexes
-
STIHL MM 55 Manuel utilisateur
-
STIHL BF-MM, BK-MM Manuel utilisateur
-
STIHL RL-MM Manuel utilisateur
-
STIHL MM 56 Manuel utilisateur
-
STIHL KB-MM, KW-MM Manuel utilisateur
-
-
-
-
-