Maytag MGDZ600TK2 Le manuel du propriétaire

Marque: Maytag

Modèle: MGDZ600TK2

Taper: Le manuel du propriétaire

EPIC

GAS DRYER

USE & CARE GUIDE

SECADORA A GAS

MANUAL DE USO Y CUIDADO

SECHEUSE A GAZ

GUIDE D'UTILISATION ET D'ENTRETIEN

FOR QUESTIONS ABOUT FEAIIJRES, OPERATION/PERFORMANCE,

PARTS, ACCESSORIES OR SERVICE CALL: 1.800.688.9900

IN CANADA, CALl: 1.800.807.6777

VISIT OUR WEBSII E AI WWW.MAYTAG.COM

IN CANADA, WWW.MAY EAG.CA

W10112943A

SI IIENE PREGUN[AS RESPECTO A [AS CARACTER[STICAS,

FUNCIONAMIENTO, RENDIMIENTO, PARIES, ACCESORIOS O

SERVIC[O TECNICO, LI AME AL: 1.800.688.9900

EN CANAD,g,, El AME AL: 1.800.807.6777

VISITE NUESTRO SITIO WEB EN

_/_/_A/.MAYTAG .COM

EN CANAD,g,, WWW.MAYEAG.CA

AU CANADA, POUR ASSISIANCE, INSTALLA|ION OU SERVICE,

COMPOSEZ I E : 1.800.807.6777

OU VISITER NOTRE SITEINTERNET ,_

WWW.MAYTAG.CA

_£:iiiiiiiiiiiiii@£!!@i!!!iiiiiii_ii_!!iiii!£_i_£_i__i:i!:_:_i!!iii!!i_ii_i!!_{_!i(!!_!_!_!_!!_iiiiiiiiiiiiiiiiiiiiiiiiiiii_i_i_¸¸

TABLE OF CONTENTS

DRYER SAFETY ...................................................................... 3

INSTALLATION INSTRUCTIONS ......................................... 5

Tools and Parts ................................................................... .-_

Optional Pedestal ............................................................... 5

Location Requirements ....................................................... 6

Electrical Requirements ...................................................... 8

Gas Supply Requirements .................................................. 9

Venting Requirements ...................................................... 10

Plan Vent System .............................................................. 12

Install Vent System ........................................................... 1_¢

Install Leveling Eegs ......................................................... 1_

Make Cas Connection ...................................................... 14

Connect Vent ................................................................... 15

Level Dryer ...................................................................... 15

Reverse Door Swing ......................................................... 15

Complete Installation ....................................................... 17

DRYER USE.......................................................................... 18

Starting Your Dryer ........................................................... 18

Stopping or Restarting Your Dryer .................................... 19

I.ock Controls ................................................................... 19

Drying and Cycle Tips ...................................................... 19

Status I.ights ...................................................................... 20

Cycles .............................................................................. 20

Additional Features .......................................................... 21

Changing Cycles, Options and Modifiers ......................... 22

Drying Rack Option ......................................................... 22

DRYER CARE ...................................................................... 23

Cleaning the Dryer I.ocation ............................................ 2_

Cleaning the Lint Screen .................................................. 23

Cleaning the Dryer Interior ............................................... 24

Removing Accumulated Lint ............................................ 24

Vacation and Moving Care .............................................. 24

TROUBLESHOOTING ......................................................... 25

ASSISTANCE OR SERVICE ................................................... 27

WARRANTY ........................................................................ 28

_!_!_ii_!iii!_iii!!!iiii!!_iiii!i_!i:_i_iiiiii!i!ii!!_!!_jiii_¸ _i!iii!i£@:!i!ii@iiiiiiiiX{!!!!!!!!!!!!!!!!!!!!!!!!!!!@¢

INDICE

SEGURIDAD DE LA SECADORA ........................................ 29

INSTRUCCIONES DE INSTALACION ................................ 31

Herrarnientas y piezas ..................................................... 31

Pedestal optional ............................................................ 31

Requisitos de ubicaciGn ................................................... 32

Requisitos elGctricos ........................................................ 35

Requisitos del suministro de gas ...................................... 36

Requisitos de ventilaciGn ................................................. 37

PlanificaciGn del sistema de ventilaciGn .......................... 39

InstalaciGn del sistema de ventilaciGn ............................. 40

InstalaciGn de las patas niveladoras ................................. 40

ConexiGn del suministro de gas ....................................... 41

ConexiGn del ducto de escape ........................................ 42

NivelaciGn de la secadora ............................................... 42

CGmo invertir el cierre de la puerta ................................. 42

Complete la instalaciGn ................................................... 44

USO DE LA SECADORA ..................................................... 45

Puesta en marcha de la secadora ..................................... 45

Detenci6n o reanudaci6n de la marcha de la secadora... 46

Bloquear los controles ..................................................... 46

Sugerencias de ciclos y secado ........................................ 47

I.uces de estado ............................................................... 47

Ciclos .............................................................................. 48

Caracter[sticas adicionales ............................................... 49

Cambio de ciclos, opciones y modificadores .................. 49

OpciGn de estante de secado .......................................... 50

CUIDADO DE LA SECADORA .......................................... 51

Limpieza del lugar donde est.1 la secadora ...................... 51

I impieza del filtro de pelusa ............................................ 51

I]mpieza del interior de la secadora ................................ 5I

EliminaciGn de pelusa acumulada ................................... 52

Cuidado para las vacaciones y la mudanza ..................... 52

SOLUCION DE PROBLEMAS ............................................. 52

AYUDA O SERVICIO Tf_CNICO ......................................... 54

GARANTJA ......................................................................... 55

__!_i!!iiiiiiiiiiiiiiiiiiiiiiiiii!i!!@ii!!!!!!!!!!!!!!!!!ili!i!i!!ii!i!!:_jiib 5ii!i£@iiii_ii!iiii!_£!il]iiiiiiiiiiiiiiii_i_!ii!{iiiiiiill¸i_

TABLE DES MATIERES

Sf_CURITI_ DE LA Sf_CHEUSE ............................................... 56

INSTRUCTIONS D'INSTALLATION ................................... 58

Outillage et pi_ces ........................................................... 58

PiGdestal facultatif ............................................................ 58

Exigences d'emplacement ................................................ ,g9

SpGcifications 61ectriques ................................................. 61

Alimentation en gaz ......................................................... 62

Exigences concernant 1'Gvacuation .................................. 64

Planification du systGme d'Gvacuation ............................. 65

Installation du systGme d'Gvacuation ................................ 67

Installation des pieds de nivellement ............................... 67

Raccordement au gaz ...................................................... 68

Raccordement du conduit d'Gvacuation .......................... 68

Mise _ niveau de la sGcheuse ........................................... 69

Inversion du sens d'ouverture de la porte ........................ 69

Achever I'installation ....................................................... 71

UTILISATION DE LA Sf_CHEUSE ........................................ 72

Mise en marche de la s6cheuse ....................................... 72

Arr@ ou remise en marche de la s6cheuse ....................... 7_¢

Verrouillage des commandes ........................................... 73

Conseils pour le s6chage et les programmes .................... 74

T6moins lumineux ........................................................... 74

Programmes ..................................................................... 75

Caract6ristiques suppl6mentaires ..................................... 76

Changement des programmes, options et

modificateurs ................................................................... 77

Option de grille de s6chage ............................................. 77

ENTRETIEN DE LA SI_CHEUSE ........................................... 78

Nettoyage de I'emplacement de la sGcheuse ................... 78

Nettoyage du filtre _ charpie ............................................ 78

Nettoyage de I'intGrieur de la sGcheuse ............................ 79

Retrait de la charpie accumulGe ....................................... 79

PrGcautions _ prendre pour les vacances et avant un

dGmGnagement ................................................................ 79

DI_PANNAGE ...................................................................... 80

ASSISTANCE OU SERVICE .................................................. 82

GARANTIE .......................................................................... 83

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

I WARNING: For your safety, the information in this manual must be followed to minimize

the risk of fire or explosion, or to prevent property damage, personal injury, or death,

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Clear the room, building, or area of all occupants.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

[] Read all instructions before using the dryer.

[] Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to

a chemical reaction that could cause a load to catch fire.

[] Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry-

cleaning solvents, or other flammable or explosive

substances as they give off vapors that could ignite or

explode.

[] Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is

used near children.

[] Before the dryer is removed from service or discarded,

remove the door to the drying compartment.

[] Do not reach into the dryer if the drum is moving.

[] Do not install or store the dryer where it will be exposed

to the weather.

[] Do not tamper with controls.

[] Do not repair or replace any part of the dryer or attempt

any servicing unless specifically recommended in this

Use and Care Guide or in published user-repair

instructions that you understand and have the skills to

carry out.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

[] Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

[] Clean lint screen before or after each load.

[] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

[] The interior of the dryer and exhaust vent should be

cleaned periodically by qualified service personnel.

[] See installation instructions for grounding requirements.

SAVE THESE iNSTRUCTiONS

In the State of Massachusetts, the following installation instructions apply:

[] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

[] If using a ball valve, it shall be a T-handle type.

[] A flexible gas connector, when used, must not exceed 3 feet.

iMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

:ili;iiiiiiiiiiiiiiiiiiiiiiiiiiii!iiiiiiiiiIi!iiiiIi!iiiiIi!iiiiIi!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiii_iii!i:iii!_!_!_!_!_i!!ii!_i!_!_!_!_!_i!i_ii!_i!ii!!_!_!_!_!!!g!!>:i_!;i_!!!ii:;>_!_i_!;i_!_i!!!!!!!!!_i_!ii!!!_i!!_!iiiii!_!:!_!!il!!!!!!!ii!_iiiiiii_i¸ !!_!_!_!_!_!_i!i_ii!_i!_ii!!_!_!_!_!_i!i_ii1!_!_!_!_!!_!Ii_i!ii_i_!!!iii!i:iii!!_i!!ii_iiii!!_!_i!i_ii!_i_!ii!ii!!_!_!!i!!:!ii_iiii_iXi_i_i_i!i!iiiii_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i!!!iiiiiiiiiiiiiiiiiiiiiiiiiiiii_!i_¸i¸

INSTALLATION INSTRUCTIONS

Gather fine required tools and parts before starting installation. Read and follow the

instructions provided with any tools listed here.

• 8" or 10" pipe wrench

• 8" or 10" adjustable wrench (for gas

connections)

• Flat-blade screwdriver

• Adjustable wrench that opens to 1"

(2.54 cm) or hex-head socket wrench

(for adjusting dryer feet)

• V2' nut driver or socket wrench

(recommended)

• level

• Vent clamps

• Knife

• Pipe-joint compound resistant to [.P gas

• Caulking gun and compound (for

installing new exhaust vent)

• Pliers

• Tape measure

Are you placing the dryer on a pedestal? You have the option of purchasing pedestals of

different heights separately for this dryer. You may select a 10" (25.4 cm) pedestal or a

15.5' (5¢9.4 cm) pedestal with a storage drawer. [he pedestal will add to the total height of the

dryer for a total height of approximately 46" (11 6.8 cm) or 51.5' (1 _¢0.8cm), respectively.

For a garage installation, you will need to place the 10" (25.4 cm) pedestal at least

9' (22.9 cm) above the floor. You will need to place the 15.5' (5¢9.4 cm) pedestal at least

3' (7.6 cm) above the floor.

Parts supplied

Remove parts package from dryer drum. Check that all parts were included.

4 [ewfling legs

NOTE: Do not use leveling legs if installing the dryer on a pedestal.

Parts needed

Check local codes and with gas supplier. Check existing gas supply, electrical supply and

venting. Read "Electrical Requirements," "Gas Supply Requirements" and "Venting

Requirements" before purchasing parts.

• For close-clearance installations between 28.65" (72.77 cm) and 34.15" (86.74 cm), see

"Plan Vent System" section for venting requirements.

(86.74 cm)

Mobile home installations require special parts (listed following) that may be ordered by

calling the dealer from whom you purchased your dryer. For further information, please refer

to the "Assistance or Service" section.

• Mobile Home Installation Kit. Ask for Part Number 346764.

Optional pedestal ( t5.5" 139.4 cm] model shown)

The pedestals are available in several colors.

lb order, call the dealer from whom you purchased your dryer or refer to the "Assistance or

Service" section.

Pedestal Height Color Part Number

10" (25.4 cm) White MHP1000SQO

10" (25.4 cm) Black MHP1000SB0

15.5" (39.4 cm) White MHP1500SQ0

15.5" (39.4 cm) Black MHP1500SB0

15.5" (39.4 cm) Pacific Blue MHP1500SK0

Stack Kit

Are you planning to stack your washer and dryer? 1o do so, you will need to purchase a Stack

Kit. lo order, call the dealer from whom you purchased your dryer or refer to the "Assistance

or Service" section. Ask for Part Number 8212640.

• Metal exhaust system hardware.

I( (.= Iio

Dryer Dimensions

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

(91.4 cm)

50"

128.27 cm)

You will need

• A location that allows for proper exhaust installation. A gas dryer must be exhausted to

the outdoors. See "Venting Requirements."

• A grounded electrical outlet located within 2 ft (61 cm) of either side of the dryer. See

"Electrical Requirements."

• A sturdy floor to support the total dryer weight of 200 Ibs (90.7 kg). The combined weight

of a companion appliance should also be considered.

• A level floor with a maximum slope of 1" (2.5 cm) under entire dryer. (if slope is greater

than 1" [2.5 cm], install Extended Dryer Feet Kit, Part No. 279810.) Clothes may not

tumble properly and automatic sensor cycles may not operate correctly if dryer is not

level.

• For a garage installation, you will need to place the dryer at least 18" (46 cm) above the

floon If using a pedestal, you will need 18" (46 cm) to the bottom of the dryer.

Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer

might not shut off at the end of an automatic cycle. Drying times can be extended.

The dryer must not be installed or stored in an area where it will be exposed to water and/or

weather.

Check code requirements. Some codes limit, or do not permit, installation of the dryer in

garages, closets, mobile homes, or sleeping quarters. Contact your local building inspector.

NOTE: No other fuel-burning appliance can be installed in the same closet as a dryer.

Installation clearances

The location must be large enough to allow the dryer door to open fully.

*Most installations require a minimum 5" (12.7 cm) clearance behind the dryer for the

exhaust vent with elbow. See "Venting Requirements."

Installation spacing for recessed area or closet installation

The following spacing dimensions are recommended for this dryer. This dryer has been tested

for spacing of 0" (0 cm) clearance on the sides and rear. Recommended spacing should be

considered for the following reasons:

• Additional spacing should be considered for ease of installation and servicing.

• Additional clearances might be required for wall, door and floor moldings.

• Additional spacing should be considered on all sides of the dryer to reduce noise transfer.

• For closet installation, with a door, minimum ventilation openings in the top and bottom

of the door are required. [ ouvered doors with equivalent ventilation openings are

acceptable.

• Companion appliance spacing should also be considered.

Custom undercounter installation - Dryer only

.... 2"*

"'1o 'c

1"* _ "_-_27"_ "_-- 1"*

2.5 crn 68.6 cm 2.5 cm

*Required spacing

Closet installation - Dryer only

II "1:11_1tll I I 24in.2 _

L_I(155o=2,

h"*_ 20.05"_1_"**1

(2.5 cm) (72.77 cm) (12.7 cm)

A B

A. _id_' vi_'w - closet or confined area

B.Closet door with vents

*Required spacing

**For side or bottom venting, O" (0 cm) spacing is allowed.

Recessed or closet installation - Dryer on pedestal

I O0

23.*

(7.6 crn)

1"--_ I_ 27"_'t "_--1" 11"*1"_26.65"_'-Is"**l

(2.5 cm) ' (68.6 cm) ' (2.5 cm) (2.5 crn) (72.77 crn) (12.7 cm)

A B

A. R_'c_'ss_'ctar_'a

B. Side"vie'w - closet or confined are'a

*Required spacing

**For side or bottom venting, O" (0 cm) spacing is allowed.

7"*(17.8cm)

* Required spacing

7"*(17.8crn)

[9"*

r (22.9 crn)

,, ,, ..........................

(12.7 cm)(72.77crn) (2.5cm) (2.5crn)(58.5cm)(2.5 cm)

** For side or bottom venting, 0" (0 cm) spacing is allowed.

Recommended installation spacing for recessed or closet installation, with

stacked washer and dryer

The dimensions shown are for the recommended spacing.

48 iil. 2 *

(310 crn2)

24 ill 2 *

(155cm2)

3"* (7.6 cm)

3"*(7.6crn)

1"*(2.5cm)

*Required spacing

Recommended installation spacing for cabinet installation

• For cabinet installation, with a door, minimum ventilation openings in the top of the

cabinet are required.

!_i¸I¸I¸I¸I¸I¸I¸I¸I¸i¸II!I¸iii_:!_ii!iii!iii!iiiiiiiiiiiiiiiiiiii¸i¸i¸iiii!!:_iii_!i!_!i!i;iiiiiiiiiiiiiiiii ....iiii_,_,_,_,_,_,_,_,_,_7

72"

(162.9 crn)

(2.5crn)

5Y2"**--_- ,_- 1"

(14crn) (2.5crn)

_- .Jj

(66.6 cm)

*Required spacing

**For venting out the side, 1"/2.5 cm) spacing is allowed.

Mobile home - additional installation requirements

This dryer is suitable for mobile home installations.

The installation must conform to the Manufactured Home Construction and Safety Standard,

Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and

Safety, Title 24, HUD Part 280) or to the Canadian Manufactured Home Standard,

CAN/CSA-Z240 MH.

Mobile home installations require:

[] Metal exhaust system hardware, which is aw3ilable for purchase from your dealer.

[] Mobile Home Installation Kit Part Number 346764. See '"]bols and Parts" section for

information on ordering.

[] Special provisions must be made in mobile homes to introduce outside air into the dryer.

[he opening (such as a nearby window) should be at least twice as large as the dryer

exhaust opening.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

120 Volt, 60 Hz., AC only, 15- or 20-amp fused electrical supply is required. A time-delay

fuse or circuit breaker is recommended. [t is also recommended that a separate circuit

serving only this dryer be provided.

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with the

dryer: if it will not fit the outlet, have a proper outlet installed

by a qualified electrician.

SAVE THESE INSTRUCTIONS

8 ...........

Explosion Hazard

Use a new CSA international approved gas supply line.

Install a shut=off valve.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 13" (33 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel,

Failure to do so can result in death, explosion, or fire.

Gas Type

Natural gas:

This dryer is equipped for use with Natural gas. It is design-certified by CSA International for

[P/propane or butane) gases with appropriate conversion.

• Your dryer must have the correct burner for the type of gas in your home. Burner

information is located on the rating plate in the door well of your dryer. If this information

does not agree with the type of gas available, contact your dealer or call the phone

numbers referenced in the "Assistance or Service" section.

LP gas conversion:

Conversion must be made by a qualified technician.

No attempt shall be made to convert the appliance from tile gas specified on the r'nodel/serial

rating plate for use with a different gas without consulting your gas company.

Gas Supply Line:

• Must include 1/8"NPT minimum plugged tapping accessible for test gauge connection,

immediately upstream of the gas connection to the dryer (see illustration).

• Y2" IPS pipe is recommended.

• %" approved aluminum or copper tubing is acceptable for lengths under 20 ft (6.1 m) if

local codes and gas supplier permit.

• If you are using Natural gas, do not use copper tubing.

• lengths over 20 ft (6.1 m) should use larger tubing and a different size adapter fitting.

• If your dryer has been converted to use [P gas, %" I.P compatible copper tubing can be

used. If the total length of the supply line is more than 20 ft (6.1 m), use larger pipe.

NOTE: Pipe-joint compounds that resist the action of I.P gas must be used. Do not use

TEFI.ON _'_tape.

• Must include a shutoff valve:

In the U.S.A.:

An individual manual shutoff w_lve must be installed within six (6) feet (1.8 m) of the dryer

in accordance with the National Fuel Gas Code, ANSI Z223.1. ]he location should be

easy to reach for opening and closing.

In Canada:

An individual manual shutoff valve must be installed in accordance with tile Bq49.1,

Natural (];as and Propane Installation Code. [t is recommended that an individual manual

shutoff valve be installed within six (6) feet (1.8 m) of the dryer. The location should be

easy to reach for opening and closing.

A C E

B D

A. ?g" flexible gas connector

B. _" pipe to flare adapter fitting

C. _" NPT minimum plugged tapping

D. _//' NPT gas supply line

E. Gas shutoff valve

t®TEFLON is a legistered trademark of E.I. DLI Pont De Nemouls and Company.

Gas supply connection requirements

• Use an elbow and a %" flare x %" NPT adapter fitting between file flexible gas connector

and the dryer gas pipe, as needed to avoid kinking.

• Use only pipe-joint compound. Do not use TEFI.ON _'*tape.

• [his dryer must be connected to the gas supply line with a listed flexible gas connector

that complies with the standard for connectors for gas appliances, ANSI Z21.24 or

CSA 6.10.

Burner input requirements

Elevations up to 10,000 ft (3,048 m):

• The design of this dryer is certified by CSA International for use at altitudes up to 10,000 ft

(3,048 m) above sea level at the Btu rating indicated on the model/serial number plate.

Burner input adjustments are not required when the dryer is operated up to this elevation.

Elevations above 10,000 ft (3,048 m):

• When installed above 10,000 ft (3,048 m) a 4% reduction of the burner Btu rating shown

on the model/serial number plate is required for each ,000 ft (305 m) increase in

elevation.

Gas supply pressure testing

• The dryer must be disconnected from the gas supply piping system during pressure testing

at pressures greater than _/2psi.

Dryer gas pipe

• The gas pipe that comes out through the rear of your dryer has a %" male pipe thread.

A. 1/_,, NPT gas supply line

B. _" NPT dryer pipe

*NOTE: If the dryer is mounted on a pedestal, the gas pipe height must be an additional

10. (25.4 cm) or1 _._.._r_,,/39.4 cm) from the floor, del)ending on the pedestal modeh For a

garage installation, the gas pipe height must be an additional 18" (46 cm) from the floor.

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death

or fire.

WARNING: lb reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

The dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling or a

concealed space of a building.

If using an existing vent system

• C'lean lint from the entire length of the system and make sure exhaust hood is not plugged

with lint.

• Replace any plastic or metal foil vent with rigid or flexible heavy metal vent.

• Review Vent system chart. Modify existing vent system if necessary to achieve the best

drying performance.

If this is a new vent system

Vent material

• Use a heavy metal vent. Do not use plastic or metal foil vent.

• 4" (10.2 cm) heavy metal exhaust vent and clamps must be used.

4" (10.2 cm) heavy metal _'xhaust v_'nt

Vent products can be purchased from your dealer or by calling Maytag Services. For more

information, see the "Assistance or Service" section.

10 ...........

Rigid metal vent

• For best drying performance, rigid metal vents are recommended.

• Rigid metal vent is recommended to avoid crushing and kinking.

Flexible metal vent

• Flexible metal vents are acceptable only if accessible for cleaning.

• Flexible metal vent must lye fully extended and supported when the dryer is in its final

location.

• Remove excess flexible metal vent to avoid sagging and kinking that may result in

reduced airflow and poor performance.

• Do not install flexible metal vent in enclosed walls, ceilings or floors.

Elbows

45 ° elbows provide better airflow than 90 ° elbows.

Clamps

Good Better

Use clamps to seal all joints.

Exhaust vent must not be connected or secured with screws or other fastening devices

that extend into the interior of the duct. Do not use duct tape.

Clamp

Exhaust

Recommended hood styles are shown here.

(10.2 cm)

A. Louv_'md hood style

B.Box hood style

The angled hood style (shown here) is acceptable.

(10.2 cm)_

v_ 21/2"

(6.4 cm)

• An exhaust hood should cap the vent to keep rodents and insects from entering the home.

• Exhaust hood must lye at least 12" (30.5 cm) from the ground or any object that may be in

the path of the exhaust (such as flowers, rocks or bushes, snow line, etc./.

• Do not use an exhaust hood with a magnetic latch.

improper venting can cause moisture and lint to collect

indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint, wallpaper,

carpets, etc.

[] Housecleaning problems and health problems.

Choose your exhaust installation type

Recommended exhaust installations

Typical installations vent the dryer from the rear of the dryer. Other installations are possible.

......................................C

.....................................G

A. Dryer

B. Elbow

C. Wall

D. Fxhaust hood

E. Cla raps

£ Rigid metal or flexible metal vent

G. Vent length necessary to connect elbows

H. fxhaust outlet

Optional exhaust installations

Fire Hazard

Cover unused exhaust holes with one of the

following kits:

279818 (white)

279820 (black)

280102 (pacific blue)

Contact your local dealer.

Failure to follow these instructions can result in death,

fire, electrical shock, or serious injury.

This dryer can be converted to exhaust out the right side, left side, or through the bottom.

Contact your local dealer to have the dryer converted.

A. Standard rear offset exhaust installation

B. Left or right side exhaust installation

C. Bottom exhaust installation (not an option with

pedestal installations)

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for your installation. Two close-

clearance installations are shown. Refer to the manufacturer's instructions.

!z__,'>... ...........

i i

, ._===-f/"

i i /z

i t/

i u

x\ ii

,.__ _ X.L __

A B

A. Over-the-top installation taho available with one

offset elbow)

B.P_'riscope installation

NOTE: The following kits for close clearance alternate installations are available for purchase.

Please see the "Assistance or Service" section to order.

• Over-the-]op installation:

Part Number 4396028

• Periscope Installation (For use with dryer vent to wall vent mismatch/:

Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm) mismatch

Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm) mismatch

Part Number 4396014- 29" (73.66 cm) to 50" (127 cm) mismatch

Special provisions for mobile home installations

The exhaust vent must be securely fastened to a noncombustible portion of the mobile home

structure and must not terminate beneath the mobile home. [erminate the exhaust vent

outside.

Determine vent path

• Select the route that will provide the straightest and most direct path outdoors.

• Plan the installation to use the fewest number of elbows and turns.

• When using elbows or making turns, allow as much room as possible.

• Bend vent gradually to avoid kinking.

• Use the fewest 90 ° turns possible.

Determine vent length and elbows needed for best drying performance

• Use the following Vent system chart to determine type of vent material and hood

combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified in the Vent system chart. Exhaust

systems longer than those specified will:

• Shorten the life of the dryer.

• Reduce performance, resulting in longer drying times and increased energy usage.

]he Vent system chart provides venting requirements that will help to achieve the best drying

performance.

Vent system chart

NOTE: Side and bottom exhaust installations have a 90 ° turn inside the dryer. lb determine

maximum exhaust length, add one 90° turn to the chart.

Number of Type of Box or Angled

90 ° turns vent Iouvered hoods

or elbows hoods

0 Rigid metal 64 ft (20 m) 58 ft (17.7 m)

Flexible metal 36 ft (11 m) 28 ft/8.5 m)

1 Rigid metal 54 ft (16.5 m) 48 ft (14.6 m)

Flexible metal 31 ft (9.4 m) 23 ft (7 m)

2 Rigid metal 44 ff (13.4 m) 38 ft (11.6 m)

Flexible metal 27 ff (8.2 m) 19 ft (5.8 m)

3 Rigid metal 35 ft (10.7 m) 29 ft (8.8 m)

Flexible metal 25 ff (7.6 m) 17 ft (5.2 m)

4 Rigid metal 27 ff (8.2 m) 21 ft (6.4 m)

Flexible metal 23 ff (7 m) 15 ft (4.6 m)

Install exhaust hood. Use caulking compound to seal exterior wall opening around

exhaust hood.

Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust

hood with 4" (10.2 cm) clamp.

Run vent to dryer location. Use the straightest path possible. See "]Z)etermine vent path" in

"Plan Vent System." Avoid 90° turns. Use clamps to seal all joints. Do not use duct tape,

screws or other fastening devices that extend into the interior of the vent to secure vent.

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

lb protect the floor, use a large flat piece of cardboard from the dryer carton. Place

cardboard under the entire back edge of the dryer.

!_iiiilZii!iiii_:!!ii!iii!iii!iiiiiiiiiiiiiiiiiiiiiiiiii!!:_%iiiiiiii ....iiii_,_,_,_,_,_,_,_,_,_I:}

2. Firmly grasp the body of the dryer. Gently lay the dryer on the cardboard. See illustration.

3. Examine the leveling legs. Find the diamond marking.

4. Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the

diamond marking is no longer visible.

5. Place a carton corner post from dryer packaging under each of the 2 dryer back corners.

Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location.

Leave enough room to connect the exhaust vent or gas line.

For mobile home use

Gas dryers must be securely fastened to the floor at the time of installation.

Mobile home installations require a Mobile Home Installation Kit. For more information,

please reference the service numbers in the "Assistance or Service" section.

Remove the red cap from the gas pipe.

Using a wrench to tighten, connect the gas supply to the dryer. Use pipe-joint compound

on the threads of all non-flared male fillings. If flexible metal tubing is used, lye sure there

are no kinks.

A ........

A. Hared male fitting

B. Non-flared male fitting

NOTE: For [.P gas connections, you must use pipe-joint compound resistant to the action

of [P gas. Do not use TEFLON _°*tape.

A combination of pipe fittings must lye used to connect the dryer to the existing gas line.

Shown is a recommended connection. Your connection may lye different, according to the

supply line type, size and location.

A. _" flexible gas connector

B. ?_" dryer pipe

C. _" to _" pipe elbow

D. _" pipe-to-flare adapter fitting

t(=:TEFLON is a legistered trademark of E.I. Du Pont De Nemours and Company.

14 ...........

3. Opentheshutoffvalveinthesupplylille,lhevalveisopenwhenthehandleisparallelto

thegaspipe.

A. Closed valve

B.Open valve

[_st all connections by brushing on an approved noncorrosive leak-detection solution.

Bubbles will show a leak. Correct any leak found.

£o nect %n

1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to

existing vent, make sure the vent is clean. [-he dryer vent must fit over the dryer exhaust

outlet and inside the exhaust hood. Check that the vent is secured to exhaust hood with a

4" (10.2 cm) clamp.

2. Move dryer into its final location. Do not crush or kink vent.

3. (On gas models) Check that there are no kinks in the flexible gas line.

4. Once the exhaust vent connection is made, remove the corner posts and cardboard.

Check the levelness of the dryer. Check levelness first side to side, then front to back.

If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs

up or down and check again for levelness.

You can change your door swing from a right-side opening to a left-side opening, if desired.

1. Place a towel or soft cloth on top of the dryer or work space to protect the surface.

Remove the door assembly

1. Remove the 4 screws that hold the door hinge on the front panel of the dryer.

A. Dryer front panel

B. Door assembly

2. I.ay the door assembly on a flat, protected surface with the inside (inner door assembly/

facing up.

3. Remove the 6 Phillips head screws to release the outer door assembly from the inner door

assembly, as indicated below. See illustration. It is important that you remove only the

6 indicated screws.

4. I.ift the inner door assembly off the outer door assembly.

5. Rotateouterdoor180°.

180 °

Reverse hinge

1. Use a small flat-blade screwdriver to remove 2 plug strips from the inner door. Slide the

head of the screwdriver under the plugs, being certain not to scratch the inner door

surface, lift up.

Remove the 4 screws that attach to the inner door hinge and move the hinge to the other

side. Reinstall the 4 screws.

°/

A. Door hinge

3. Reinstall plug strips on opposite side of the inner door.

4. Check for fingerprints on the glass. Clean glass if necessary.

5. Place the inner door assembly inside the outer door assembly. To fit correctly, the inner

door assembly edge fits completely inside the outer door assembly edge.

6. Reassemble the inner and outer door assemblies with the 6 screws.

16 ...........

Reverse the strike

1. Use a small flat-blade screwdriver to remove plug strip from the dryer door opening. Slide

the head of the screwdriver under the plugs, being certain not to scratch the dryer surface.

I.ifl up.

2. Remove the strike

3. Insert strike on the opposite side.

(

A. Plug strip (cannot be seen from thi_ angle)

B.Door strike

Reinstall the door

1. Reattach door to dryer front panel with the 4 screws.

1. Check that all parts are now installed. If there is an extra part, go back through the steps to

see which step was skipped.

2. Check that you have all of your tools.

3. Check the dryer's final location. Be sure the vent is not crushed or kinked.

4. Check that the dryer is level. See "level Dryer."

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result indeath,

fire, or electrical shock.

\\\\\

10.

A. Dryer front panel

B.Door assembly 11.

2. Check for fingerprints on the glass. Clean glass if necessary.

3. Close door and check that it latches securely.

Plug into a grounded 3 prong outlet. Turn on power.

Remove any protective film or tape remaining on the dryer.

Dispose of/recycle all packaging materials.

Read "Dryer Use."

Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.

Select a Timed Dry heated cycle, and start the dryer. Do not select the Air Only

[emperature setting.

If the dryer will not start, check the following:

• Controls are set in a running or "On" position.

• Start button has been pushed firmly.

• Dryer is plugged into a grounded 3 prong outlet.

• Electrical supply is connected.

• Household fuse is intact and tight, or circuit breaker has not tripped.

• Dryer door is closed.

When the dryer has been running for 5 minutes, open the dryer door and feel for heat. [f

you feel heat, cancel cycle and close door. If you do not feel heat, turn off the dryer and

check that the gas supply line shutoff valve is open.

• [f the gas supply line shutoff valve is closed, open it, then repeat the 5-minute test as

outlined above.

• If the gas supply line shutoff valve is open, contact a qualified technician.

POWER DELICATE

WET 1 WRINKLE

DAMP 0 CONTROL

COOL DOWN NORMAl,,

DRY MOll

WRINKLE PREVENT _OtM_L

CONTROLS LOCKED ;_i 0 TOWEL£COTTON/_

CLEAN LINT SCREEN !!_!!

DRYNESS

LEVEL

START

PAUSEo

CANCEL

_Juft

HIGH

REGULAR

MEDIUM

LOW

EXTRA LOW

AIR FLUFF

O WRINKLE

PREVENT

-,_--,,,............. ,t,,_I( I.II" I.FI"_/I)I

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not dry anything that has ever had anything

flammable on it (even after washing).

Failure to follow these instructions can result in death,

explosion, or fire.

Fire Hazard

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on

it (including cooking oils).

Items containing foam, rubber, or plastic must be dried

on a clothesline or by using an Air Cycle.

Failure to follow these instructions can result in death

or fire.

Follow these basic steps to start your dryer. Please refer to specific sections of this manual for

more detailed information. This information covers several different models. Your dryer

may vary from the model shown and may not have all the cycles and features described.

1. Clean lint screen before each load. See "Cleaning the I.int Screen."

2. Place laundry in dryer and shut door.

3. Press POWER.

Select a Sensor Dry or Timed Dry Cycle. The preset setti%s for Sensor Dry or Timed Dry

Cycles will illuminate. The estimated (Sensor Dry cycle) or actual (Timed Dry) cycle time

(in minutes) will show in the display.

NOTE: A default time is displayed when an automatic cycle is selected. Durin# the first

few minutes of the dryi% process, the cycle time may automatically vary from the default

time based on the size and fabric type of the load. toward the end of the dryin8 process,

the estimated time display will adjust asain, showin# the final dryi% time.

To use a Sensor Dry Cycle

• Select a Sensor [Dry Cycle. Sensor Dry Cycles are preset to Normal Cycle.

• Select DRYNESS I.EVEI. to adjust how dry you want the load. As the cycle runs, the

control senses the dryness of the load and adjusts the time automatically for the

selected dryness level.

To make changes to the Dryness Level and/or Options during a Sensor Dry Cycle:

• Press PAUSE/CANCEl once.

• Adjust Dryness I.evel and/or Options.

NOTE: Dryness I.evel selections can be made only while using Sensor Dry Cycles.

Selecting More, Normal or I.ess automatically adjusts the sensed time needed.

M0 RE

I NORMAL

LESS

DRYNESS

LEVEL

SENSOR DRY ONLY

Sensor Dry cycles take the guesswork out of drying time and enhances fabric care.

The amount of time that is displayed is the estimated time remaining in the cycle.

To use a Timed Dry Cycle

• Select a Nmed [Dry Cycle.

• Press the Timed Dry Cycle Adjust Up or [Down arrow buttons until the desired drying

time is displayed, lap the limed L)ry Cycle Adjust Up or L)own arrow buttons and the

time will change by 1-minute intervals. Press and hold the Timed Dry Cycle Adjust

Up or [])own arrow buttons, and the time will change by S-minute intervals.

NOTE: The Timed Dry Cycle Adjust feature can be used only with Timed [Dry Cycles.

_ TIMED DRYCYCLE

ADJUST

• Press TEMPERATURE until the desired temperature illuminates.

To make changes to Time and/or options during a Timed Dry Cycle:

• Press PAUSE/CANCEl once.

• Adjust the Time and/or Options.

iOPT[ONAL STEP) [f desired, select WRINKLE PREVENT. For more details, see "WR[NK[E

PREVENT" in the "Additional Features" section.

iOPT[ONAL STEP) The Cycle Signal is preset to on. [f desired, you may turn the Cycle

Signal off by pressing the Cycle Signal button.

Press and hold START for approximately 1 second until dryer starts. Be sure the door is

closed.

• [f you do not press Start within 5 minutes of selecting a cycle, the dryer automatically

shuts off.

To pause/stop the dryer at any time

Open the door or press PAUSE/CANCEl once.

To restart the dryer

Close the door. Press and hold START until dryer starts.

To end/cancel your dryer at any time

Press PAUSE/CANCEl. twice or open the door.

NOTE: Drying will continue from where the cycle was interrupted if you close the door and

press Start within 5 minutes. If the cycle is interrupted for more than 5 minutes, the dryer will

shut off. Select new cycle settings before restarting the dryer.

/ < "' .........L,

This feature allows you to lock your settings to avoid unintended use of the dryer. You can also

use the control lock feature to avoid unintended cycle or option changes during dryer

operation. ......

To enable the control lock feature: (,i:

Press and hold CYCI.E SIGNAl. button for 3 seconds. The CONTROI.S lOCKED icon lights

up, and a single beep tone is heard. To unlock, press and hold CYCLE SIGNAl button for

3 seconds. The indicator light turns off.

Select the correct cycle and dryness level or temperature for your load. If a Sensor [Dry Cycle

is running, @e display shows @e esfim_ted cycle time, which is determined by your dryer

automatically sensing the dryness level of your load. If a Timed Dry Cycle is running, the

display shows the exact number of minutes remaining in the cycle.

Cool Down tumbles the load without heat during the last few minutes of all cycles. Cool

Down makes the loads easier to handle and reduces wrinkling. The length of the Cool Down

depends on the load size and dryness level.

Drying tips

• Follow care label directions when they are available.

• If desired, add a fabric softener sheet. Follow package instructions.

• [b reduce wrinkling, remove the load from the dryer as soon as tumbling stops. ]his is

especially important for permanent press, knits, and synthetic fabrics.

• Avoid drying heavy work clothes together with lighter fabrics. This could cause

overdrying of lighter fabrics and lead to increased shrinkage or wrinkling.

Cycle tips

• Dry most loads using the preset cycle settings.

• Refer to the Sensor Dry Cycles or Timed Dry Cycles Preset Settings chart (in the "Cycles"

section) for a guide to drying various loads.

• Drying temperature and Dryness Level are preset when you choose an Sensor [Dry

Cycle. You can select a different dryness level, depending on your load, by pressing

Dryness ].evel and choosing More or ].ess.

NOTE: You cannot use the Timed Dry Cycle Adjust Up or Down arrow buttons and

you cannot modify temperature with the Sensor Dry cycles.

• [f you wish to adjust the cycle length of a Timed Dry Cycle, press the Timed Dry Cycle

Adjust up or down arrow buttons. Adjust the temperature of a Timed [Dry Cycle by

pressing TEMPERATURE until the desired temperature is selected.

NOTE: You cannot use the [Dryness level with Timed Dry Cycles.

Follow the progress of your dryer with the drying Status indicator lights.

WET

DAMP @

COOL DOWN

DRY

WRINKLE PREVENT

CONTROLS LOCKED

C LEAN LI NT SCREEN _:

Wet

The Wet light illuminates at the beginning of a Sensor Dry Cycle if a wet item is detected.

• In a Sensor Dry Cycle, if a wet item is not detected after approximately 5 minutes, the

dryer goes directly into Cool Down and the Cool Down and WR[NK[E PREVENT

indicators illuminate, if selected.

• In a Timed Dry Cycle, wet items are not detected. The dryer will continue to run for the

length of time selected, and the Wet light will illuminate. The damp light will not

illuminate.

WRINKLE PREVENT

The WRINKLE PREVENT light illuminates when this option is selected. This indicator stays on

with [Dry.

Clean Lint Screen

The Clean I.int Screen light is a reminder to check to see whether the lint screen needs to be

cleaned. The Clean [.int Screen light will come on when the machine is turned on. The light

will flash until the cycle is started or the door is opened, and then the light will turn off.

Indicator lights

Other indicator lights show Cycle, Options and Modifier settings selected.

Select the drying cycle that matches the type of load you are drying. See the Sensor Dry

Cycles Preset Settings chart or the Timed [Dry Cycles Preset Settings chart.

DELICATE

WRINKLE

CONTROL

NORMAL. TIMED

" DRY

JEANS - _RAPID

DRY

COTTON/ " FRESHEN

TOWELS UP

SENSOR DRY TIMED DRY

Sensor Dry Cycles

Sensor Dry Cycles allow you to match the cycle to the load you are drying. See the following

Sensor Dry Cycles Preset Settings chart. Each cycle dries certain fabrics at the recommended

temperature. A sensor detects the moisture in the load and automatically adjusts the drying

time for optimal drying.

Cotton/Towels or Heavy Duty

Use this cycle to get high heat for heavy fabrics such as cotton towels or bedspreads.

Jeans

Use this cycle to get regular heat for drying denims.

Damp

The Damp light illuminates in a Sensor Dry Cycle when the laundry is approximately 80%

dry.

Cool Down

The Cool Down light illuminates during the cool down part of the cycle. [aundry cools for

ease in handling.

Dry

The Dry light illuminates when the drying cycle is finished. ]his indicator stays on during

WRINKI.E PREVENT.

Normal

Use this cycle to get rnedium heat for drying sturdy fabrics such as sturdy work clothes and

sheets.

Wrinkle Control

Use this cycle to get low heat for drying no-iron fabrics such as sport shirts, casual business

clothes and permanent press blends.

Delicate

Use this cycle to get extra-low heat for drying synthetic fabrics, washable knit fabrics and no-

iron finishes.

20 ...........

La page charge ...

Maytag MGDZ600TK2 Le manuel du propriétaire

Marque: Maytag

Modèle: MGDZ600TK2

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag MGDZ600TK2 Owner's manual
español: Maytag MGDZ600TK2 El manual del propietario

Maytag MGDZ600TK2 Le manuel du propriétaire

Maytag MGDZ600TK2 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents