Vulcan VG30 Manuel utilisateur

Marque: Vulcan

Modèle: VG30

Taper: Manuel utilisateur

INSTALLATION &

OPERATION MANUAL

For additional information on Vulcan or to locate an authorized parts

and service provider in your area, visit our website at www.vulcanequipment.com

VULCAN

DIVISION OF ITW FOOD EQUIPMENT GROUP, LLC

WWW.VULCANEQUIPMENT.COM

3600 NORTH POINT BLVD.

BALTIMORE, MD 21222

FORM 31227 Rev. B (January 2018)

VG30, VG40, VE30 & VE40 BRAISING PANS

MODELS

VG30 ML-126847

VG40 ML-126848

VE30 ML-152047

VE40 ML-152048

Model VE40

IMPORTANT FOR YOUR SAFETY

THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS

EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS

OF THE EQUIPMENT COVERED BY THIS MANUAL.

POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT

THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OBTAINED FROM THE

LOCAL GAS SUPPLIER.

IMPORTANT

IN THE EVENT A GAS ODOR IS DETECTED, SHUT DOWN UNITS

AT MAIN SHUTOFF VALVE AND CONTACT THE LOCAL GAS

COMPANY OR GAS SUPPLIER FOR SERVICE.

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE

VAPORS OR LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER

APPLIANCE.

IMPROPER INSTALLATION, ADJUSTMENT,

ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE

PROPERTY DAMAGE, INJURY OR DEATH. READ THE

INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS

THOROUGHLY BEFORE INSTALLING OR SERVICING THIS

EQUIPMENT.

IN THE EVENT OF A POWER FAILURE, DO NOT ATTEMPT TO

OPERATE THIS DEVICE.

RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

– 2 –

©VULCAN, 2018

– 3 –

TABLE OF CONTENTS

GENERAL .............................................................................................................................................................. 4

INSTALLATION .....................................................................................................................................................4

Unpacking ........................................................................................................................................................4

Location ...........................................................................................................................................................4

Installation Codes and Standards ....................................................................................................................6

Leveling and Anchoring the Tilting Braising Pan ..............................................................................................6

Service Connections ........................................................................................................................................6

Gas Connections .............................................................................................................................................7

Testing the Gas Supply System .......................................................................................................................7

Ventilation ........................................................................................................................................................7

Control Circuit Power Connection — Gas Braising Pans ................................................................................7

Electrical Connections .....................................................................................................................................8

Installation Diagram .........................................................................................................................................9

OPERATION .......................................................................................................................................................10

Before First Use .............................................................................................................................................10

Gas Heat Braising Pans .................................................................................................................................10

Electric Heat Braising Pans ...........................................................................................................................12

Operation of the Lifting System ...................................................................................................................... 12

Unloading Prepared Foods ............................................................................................................................13

Steaming Inserts (Optional) ...........................................................................................................................14

Suggested Uses For Your Braising Pan ......................................................................................................... 14

CLEANING ..........................................................................................................................................................15

COOKING GUIDELINES (Domestic Measurements) ........................................................................................16

COOKING GUIDELINES (Metric Measurements) ..............................................................................................19

MAINTENANCE ..................................................................................................................................................22

Lubrication .....................................................................................................................................................22

Adjustments ...................................................................................................................................................22

Flue ................................................................................................................................................................22

Service and Parts Information ........................................................................................................................ 22

TROUBLESHOOTING .......................................................................................................................................23

Gas Heat Braising Pans .................................................................................................................................23

Electric Heat Braising Pans ...........................................................................................................................23

– 4 –

INSTALLATION, OPERATION AND CARE OF

TILTING BRAISING PANS

MODELS VG30, VG40, VE30 & VE40

SAVE THESE INSTRUCTIONS FOR FUTURE USE

GENERAL

Vulcan Tilting Braising Pans are available in two sizes. Models VG30 and VE30 have a 30-gallon (114 L)

capacity, and Models VG40 and VE40 have a 40-gallon (151 L) capacity.

The tilting braising pan is a versatile piece of equipment. It allows you to stew, simmer, pan fry, braise,

grill or sauté, and all with a very uniform heat pattern.

Standard features on all models include thermostat, manual lift, drop-away food pan support and four

anged feet.

Optional features include automatic power lift and casters.

Your Vulcan braising pan is produced with quality workmanship and material. Proper installation, usage

and maintenance will result in many years of satisfactory performance.

Vulcan suggests that you thoroughly read this entire manual and carefully follow all of the instructions

provided.

INSTALLATION

Before installing, verify that the electrical service and gas supply (natural or propane) agree with the

specications on the rating plate located on the left front edge of the table top.

UNPACKING

This braising pan was carefully inspected before leaving the factory. The transportation company assumes

full responsibility for safe delivery upon acceptance of this shipment.

Immediately after unpacking, check for possible shipping damage. If the tilting braising pan is found to be

damaged, save the packaging material and contact the carrier within 5 working days of delivery.

LOCATION

For Gas-Powered Braising Pans Only

The braising pan must be kept free and clear from combustible substances. The braising pan, when

installed, must have minimum clearance from combustible construction of 2" (5 cm)

from the sides

and 6" (15 cm) from the rear. Minimum clearance from noncombustible construction is 0" from the sides

and 6" (15 cm) from the rear.

– 5 –

The installation location must allow adequate clearances for servicing and proper operation. Recommended

clearances are 24" (61 cm) on the sides and back (for servicing), and 36" (91 cm) on the front.

The braising pan must be installed so that the ow of combustion and ventilation air will not be obstructed.

Adequate clearance for air openings into the combustion chamber must be provided. Make sure there

is an adequate supply of air in the room suitable for the amount of combustion gas feeding the braising

pan burners.

Do not permit fans to blow directly at the braising pan. Wherever possible, avoid open windows next to

the braising pan. Avoid wall-type fans which create air crosscurrents within the room.

Gas-Powered Braising Pans Equipped with Casters (Optional)

If casters are assembled to the braising pan, the installation must be made using:

1. A connector (not supplied by Vulcan) that complies with the Standard for Connectors for Movable

Gas Appliances, ANSI Z21.69 (latest edition) or Connectors for Movable Gas Appliances, CAN/

CGA-6.16 (latest edition).

2. A quick-disconnect device that complies with the Standard for Quick-Disconnect Devices for

Use

With Gas Fuel, ANSI Z21.41 or Quick-Disconnect Devices for Use with Gas Fuel, CAN1-

6.9

(latest edition).

Adequate means must be provided to limit the movement of the appliance, without depending on the

connector and/or any quick-disconnect device or its associated piping to limit braising pan movement.

Attach the restraint at the rear of the braising pan (Fig. 1).

Fig. 1

If disconnection of the restraint is necessary, turn o the gas supply before disconnection. Reconnect this

restraint prior to turning the gas supply on and prior to returning the braising pan to its originally installed

position.

HOLES PROVIDED

FOR RESTRAINT

PL-56652

– 6 –

INSTALLATION CODES AND STANDARDS

Your Vulcan tilting braising pan must be installed in accordance with:

In the United States:

1. State and local codes, or in the absence of local codes, with:

2. National Fuel Gas Code ANSI-Z223.1 (latest edition), available from The American Gas Association,

Inc., 1515 Wilson Boulevard, Arlington, VA 22209.

3. National Electrical Code ANSI/NFPA-70 (latest edition).

4. ANSI NFPA Standard #96 Vapor Removal from Cooking Equipment (latest edition), available from

The National Fire Protection Association, Batterymarch Park, Quincy, MA 01169.

In Canada:

1. Local codes.

2. CAN/CGA-B149.1 National Fuel Gas Code (latest edition), available from The Canadian Gas

Association, 178 Rexdale Boulevard, Etobicoke, Ontario, Canada M9W 1R3.

3. Canadian Electrical Code Part 1 CSA-C22.1 (latest edition), available from The Canadian Standards

Association, 178 Rexdale Boulevard, Etobicoke, Ontario, Canada M9W 1R3.

LEVELING AND ANCHORING THE TILTING BRAISING PAN

1. Place the braising pan in the nal installed position.

2. Place a carpenter's level on the braising pan table top and turn the adjustable feet to level the braising

pan table top side-to-side and front-to-back. Do not attempt to level the braising pan base.

3. Mark hole locations on the oor through the anchoring holes provided in the rear, anged adjustable

feet.

4. Remove the tilting braising pan from the installation location and drill holes in the locations marked

on the oor. Insert proper anchoring devices (not supplied).

5. Place the tilting braising pan back in the installation location.

6. Place a carpenter's level on top of the braising pan, and re-level side-to-side and front-to-back.

7. Bolt and anchor the tilting braising pan securely to the oor.

8. Seal bolts and anged feet with Silicon sealant or equivalent compound.

SERVICE CONNECTIONS

To access service and utility connections, remove the left side panel. To remove, hold the panel from

underneath and lift it up. While holding the panel up, swing out the lower part of the panel until it clears

the bottom ange and remove the panel. If required, the rear panel can also be removed using the same

procedure.

The gas-powered braising pan is supplied with a 120-volt power cord.

The electrical connection for the electric braising pan can be accessed from the rear or the left panel.

– 7 –

GAS CONNECTIONS (See Fig. 2)

All gas supply connections and any pipe joint compound used must be resistant to the action of propane gases.

Connect a

/4" (nominal) gas supply to the braising pan. Recommended incoming gas line pressure is 7"

W.C. (Water Column) (48.3 kPa) for natural gas or 11" W.C. (75.8 kPa) for propane gas.

Make sure the pipes are clean and free of obstructions, dirt and piping compound.

Codes require that a gas shuto valve be installed in the gas line ahead of the tilting braising pan.

Natural gas and propane gas braising pans are equipped with xed orices, and no adjustment is necessary.

The manifold is set at 3.7 W.C. (Water Column) (25.5 kPa) for natural gas and 10" W.C. (68.9 kPa) for

propane gas.

Prior to lighting, check all joints in the gas supply line for leaks. Use soap and water

solution. Do not use an open ame.

After piping has been checked for leaks, all piping receiving gas should be fully purged to remove air.

The electrical control circuit must be connected (see CONTROL CIRCUIT POWER CONNECTION in this

manual).

TESTING THE GAS SUPPLY SYSTEM

When test pressures exceed

/2 psig (3.45 kPa), the tilting braising pan and its individual shuto valve

must be disconnected from the gas supply piping system.

When test pressures are

/2 psig (3.45 kPa) or less, the tilting braising pan must be isolated from the gas

supply system by closing its individual manual shuto valve.

VENTILATION

DO NOT obstruct the ow of ue gases from the ue duct located on the rear of the tilting braising pan.

It is recommended that the ue gases be ventilated to the outside of the building through a ventilation

system installed by qualied personnel.

From the termination of the braising pan ue vent to the lters of the hood venting system, an 18"

(46

cm) minimum clearance must be maintained. The ue is not to be directly connected to the ventilation

system.

Local jurisdictions may require a ventilation system to exhaust the steam from this appliance. Clearance

should be provided for the lid to be raised without interference with the hood. A ceiling that is too low may

not allow for an installation of a hood to meet this requirement.

CONTROL CIRCUIT POWER CONNECTION — GAS BRAISING PANS (See Fig. 2)

Appliances equipped with a exible electric supply cord are provided with a three-

prong grounding plug. It is imperative that this plug be connected into a properly grounded three-

prong receptacle. If the receptacle is not the proper grounding type, contact an electrician. Do

not remove the grounding prong from this plug.

– 8 –

ELECTRICAL CONNECTIONS (SEE FIG. 2)

Electrical and grounding connections must comply with the national electrical code

and/or other local codes.

Disconnect the electrical power to the machine and follow lockout / tagout procedures.

The eld connection box for eld wire connection of Models VE30 and VE40 is located at the back of the

braising pan. A knockout hole is provided for a 1" (2.5 cm) conduit connection.

1. Remove the eld connection box cover plate. Mount suitable 1" (2.5 cm) conduit tting in the conduit

opening provided on the bottom surface.

2. Connect eld wire to the terminal block as indicated on the wiring diagram. The wiring diagram is

located on the inside of the eld box lid. Wire must be of the type suitable for 75°C service and at

the suitable gauge for loads shown on the data plate.

3. After making the connections, replace the control box cover plate.

4. The braising pan must be grounded by installing a properly grounded lead to the ground lug located

inside the eld connection box.

ELECTRICAL DATA CHART

Model

Number

V (L-L)

Rated Line Current (A)

Rated

Power

(kW)

3Ø 1Ø

L1 L2 L3

VE30-FB

208 33.3 33.3 33.3 57.7 12

240 28.9 28.9 28.9 50.0 12

480 14.4 14.4 14.4 - 12

VE40-FB

208 45.9 41.6 45.9 76.9 16

240 39.7 36.1 39.7 66.7 16

480 19.9 18.0 19.9 - 16

These values are nominal ratings. Field wire connections must be capable of withstanding anticipated

surges.

– 9 –

INSTALLATION DIAGRAM

Fig. 2

76"

(1930 mm)

36.761"

(934 mm)

.501"

(12.7 mm)

46"

(1168 mm)

36"

(914 mm)

40.75"

(1040 mm)

12"

(305 mm)

14"

(355 mm)

35.5"

(900 mm)

(153 mm)

8.75"

(222 mm)

(127 mm)

SERVICE CONNECTIONS:

ELECTRICAL: Machine is supplied with 120-VAC,

1-phase, 15-amp. power cord.

GAS INPUT: 3/4" N.P.T., Nat.6"-14" W.C.,

IMPORTANT

1. A pressure regulator sized for this unit is included. Natural gas 7"

W.C., propane gas 11" W.C. supply pressure.

propane gas 11" - 18" W.C., See capacity chart.

2. Gas line connecting to appliance must be

" or larger. If flexible

connectors are used, the inside diameter must be at least the same

as the

" iron pipe.

3. An adequate ventilation system is required for commercial cooking

equipment. Information may be obtained by writing to the National

Fire Protection Association, Batterymarch Park, Quincy, MA 02289.

When writing, refer to NFPA No. 96.

4. These units are manufactured for installation in accordance with

ANSZ223.1A (latest edition), National Fuel Gas Code. Copies may

be obtained from the American Gas Association, 1515 Wilson Blvd.,

Arlington, VA 22209.

5. Clearances: Combustible Noncombustible

Rear 6 6

Sides 2 0

6. This appliance is manufactured for commercial installation only and

is not intended for home use.

ELECTRICAL CONNECTION: 1" dia. conduit, fitting

to be installed by installer.

Cooking 4 oz.

MODEL Surface Area Capacity Portions

VE/VG30 29" x 23" 30 gal./114 liters 960

VE/VG40 39" x 23" 40 gal./152 liters 1280

BTU/hr.

MODEL Input

VG30 90,000

VG40 120,000

208

VAC

MODEL

VE30

VE40

12 KW

16 KW

12 KW

16 KW

12 WK

16 KW

240

VAC

480

VAC

PL-56638

GAS BRAISING PAN:

ELECTRICAL BRAISING PAN:

– 10 –

OPERATION

The tilting braising pan and its parts are hot. Use care when operating, cleaning

or servicing the braising pan.

BEFORE FIRST USE

Use a noncorrosive, grease-dissolving commercial cleaner to clean the protective metal oils from all

surface parts and the interior of the tilting braising pan. Follow the cleaner manufacturer's directions.

Rinse thoroughly and drain the pan. Wipe dry with a soft, clean cloth.

GAS HEAT BRAISING PANS

Controls (Fig. 3)

Fig. 3

Thermostat — Sets desired cooking temperature.

On/O Switch (Black) — Turns the braising pan on and o.

Amber Light — When lit, indicates the machine is turned on.

Heat Light (Red) — When lit, indicates the thermostat is calling for heat.

Auto. Power Lift (Gray) — (Optional). Push the upper part of the switch to raise the braising

pan; push the lower part to lower the braising pan. Always remove

the manual lift crank handle before operating the automatic power lift.

Manual Lift Crank Handle

— Use to manually raise and lower the braising pan.

PL-41750-1

THERMOSTAT

ON / OFF

SWITCH

[

] = OFF

[

] = ON

OPTIONAL

AUTOMATIC

POWER

LIFT

RED HEATLIGHT

AMBER

LIGHT

MANUAL LIFT CRANK

HANDLE

– 11 –

Lighting and Shutdown of Pilot

Lighting instructions are also located on the front panel.

1. Turn main gas supply to the braising pan to the ON position at the shuto valve.

2. Lower the braising pan (see OPERATION OF LIFTING SYSTEM in this manual). The braising pan

will not operate with the pan in the UP position (5 degrees or higher from horizontal).

3. Turn the black on/o switch to the ON position. The ON position is indicated by a glowing amber

light on the control panel.

4. Turn the thermostat to the desired cooking temperature.

5. If pilot is extinguished, turn the gas supply and the on/o switch to the OFF position. Wait 5 minutes

before relighting.

Nightly Shutdown

Turn the on/o switch to the OFF position.

Extended Shutdown

Turn the on/o switch to the OFF position and turn o the gas supply.

Operating the Gas Braising Pan

The braising pan does not require any adjustments before startup.

The entire ue duct opening (located across the rear of the braising pan) must be left uncovered.

Turn the on/o switch to the ON position and turn the thermostat to the desired temperature to put the

braising pan into operation.

To prevent discoloration of the stainless steel cooking surface, do not turn the heat on unless the braising

pan is covered with a uid, a thin layer of cooking oil or food to be cooked.

DO NOT use the braising pan as a deep fat fryer; use it only for shallow pan frying (cooking oil lm not

more than

/8" [0.3 cm] thick). Its use for deep frying could result in a re hazard. See SUGGESTED

USES FOR YOUR BRAISING PAN in this manual for additional information.

Do not overheat the clad stainless steel plate by setting the temperature well above recommended

temperatures or by operating the braising pan without any uid inside the pan to absorb heat. Overheating

the plate may cause warping and will carbonize any cooking oil on the plate and cause sticking.

In case of a power failure, there will be no ames because the combination control valve will shut o the

gas ow. In the event of a power failure, immediately turn the on/o switch to the OFF position. Once

power is restored, turn the on/o switch to the ON position to resume cooking.

The lid is spring-loaded and will stay in any position at which it is placed. After some time, the springs

may need to be tightened. Call your local Vulcan-authorized servicer to make these adjustments.

– 12 –

ELECTRIC HEAT BRAISING PANS

Controls (see Fig. 3)

Thermostat — Sets desired cooking temperature.

On/O Switch (Black) — Turns the braising pan on and o.

Amber Light — When lit, indicates the machine is turned on.

Heat Light (Red) — When lit, indicates the thermostat is calling for heat.

Auto. Power Lift (Gray) — (Optional). Push the upper part of the switch to raise the braising pan;

push the lower part to lower the braising pan. Always remove the manual

lift crank handle before operating the automatic power lift.

Manual Lift Crank Handle

— Use to manually raise and lower the braising pan.

Operating the Electric Braising Pan

The braising pans do not require any adjustments before startup.

Turn the black on/o switch to the ON position.

Lower the braising pan (see OPERATION OF LIFTING SYSTEM in this manual). The braising pan will

not operate with the pan in the UP position (5 degrees or higher from horizontal).

Turn the thermostat to the desired cooking temperature.

To prevent discoloration of the stainless steel cooking surface, do not turn the heat on unless the braising

pan surface is covered with a uid, a thin layer of cooking oil or food to be cooked.

DO NOT use the braising pan as a deep fat fryer; use it only for shallow pan frying (cooking oil lm not

more than

/8" [0.3 cm] thick). Its use for deep frying could result in a re hazard. See SUGGESTED

USES FOR YOUR BRAISING PAN in this manual for additional information.

Do not overheat the clad stainless steel plate by setting the temperature well above recommended

temperatures or by operating the braising pan without any uid inside the pan to absorb heat. Overheating

the plate may cause warping and will carbonize any cooking oil on the plate and cause sticking.

The lid is spring-loaded and will stay in any position at which it is placed. After some time, the springs

may need to be tightened. Call your local Vulcan-authorized servicer to make these adjustments.

OPERATION OF THE LIFTING SYSTEM

Keep the area underneath and around the braising pan clear of your hands or any other objects when

operating the lifting system.

Do not obstruct any of the moving parts of the lift system located underneath the table top on the right and/

or left side of the braising pan. This area must be kept clear of any objects or obstructions at all times.

Do not leave the braising pan in the UP position for extended periods (e.g., overnight or during a shutdown

period between cooking times).

– 13 –

Fig. 4

Braising Pans with Manual Lift (Standard)

1. The crank for the manual lift system is shipped separately.

2. There are two pins on one end of the crank. Insert the crank through the hole on the control panel

so that the two pins engage in the slots of the speed reducer coupling located behind the panel.

3. Turn the crank handle clockwise to lift the braising pan and counterclockwise to lower the braising

pan.

4. This lift system is not aected by a power failure and can be operated during a power failure.

5. Refer to the MAINTENANCE section of this manual for lubrication and maintenance instructions.

Braising Pans with Automatic Power Lift (Optional)

1. The automatic lift cannot raise the braising pan unless the lid is fully opened.

2. The pan lift is controlled by the gray rocker switch located on the control panel (see Fig. 3).

3. Always remove the manual crank handle before operating the automatic power lift.

4. Press the upper half of the gray rocker switch to raise the braising pan and the lower half of the gray

rocker switch to lower the braising pan. The switch must be held for continuous raising or lowering

of the braising pan.

5. In case of a power failure, use the hand crank (shipped separately) to lower or raise the pan (same

as the braising pans with manual lift).

UNLOADING PREPARED FOODS

All braising pans are provided with a frame support (Fig. 4) for holding a food receiving pan when unloading

prepared foods.

Pull the frame support out and up until it locks. The support will accept food receiving pans of 12" x 20"

(30 cm x 50 cm) up to 6" (15 cm) deep.

When lowering the frame support, push in on the hinges until they bend, then lower the support.

PL-41751-1

HINGE

FRAME

SUPPORT

– 14 –

STEAMING INSERTS (Optional)

Your tilting braising pan can be used for steaming frozen and fresh foods. The 30-gallon (114 L) pans

(Models VE30 or VG30) can be loaded with a maximum of two 12" x 20" x 4"

(30 cm x 50.8 cm x

10 cm) deep steaming pans. The 40-gallon (151 L) pan (Models VE40 or VG40) will accept up to three

steam pans of this same size.

To use the braising pan for steaming, ll the pan with 6 to 7 gallons (23 to 26 L) of water (approximately

2" [5 cm] deep) for 30-gallon (114 L) models and 8 to 9 gallons (30 to 34 L) of water (approximately 2"

[5 cm] deep) for 40-gallon (151 L) models.

Turn the braising pan ON. Set the thermostat at 212°F (100°C). Allow the water to come to a boil. Then

change the thermostat setting to 250°F (121°C) and carefully place the steaming inserts into the pan as

shown in Fig. 5. Place the pan with product into the steaming insert. Close the lid and allow steaming

for the desired time.

Periodically inspect the water level inside the braising pan. Add water if the water level is less than

/2"

(1 cm) deep.

To use the braising pan as a food warmer or bain marie, follow the same procedure as for steaming, but

increase the depth of the water to allow the bottom and part of the sides of the steaming inserts to be

immersed in water. Set the thermostat for the holding or warming temperature desired.

The steaming inserts can be ordered from your dealer.

Fig. 5

SUGGESTED USES FOR YOUR BRAISING PAN

DO NOT use the braising pan for deep fat frying. Restrict frying activity to shallow pan frying (oil lm not

more than

/8" [0.3 cm] thick) or sautéing.

A tilting braising pan is quite versatile. It can be used for roasting, simmering, boiling, sautéing, searing,

frying, warming, holding, proong, thawing, browning, steaming, braising, griddling or stewing. It can

be used as an oversized skillet, as a bain marie, as a proong oven, as a stock pot, as a kettle or as an

even-heat range top. It can be used for cooking breakfasts, lunches and dinners.

Your Vulcan tilting braising pan is a multi-purpose unit that can be used for virtually any type of cooking,

except deep fat frying, with great speed, in large volume and with considerable savings in labor and energy.

PL-41752-1

STEAMING INSERT

– 15 –

CLEANING

Disconnect the electrical power to the machine and follow lockout / tagout procedures

before cleaning.

Clean your braising pan regularly. Keep the plate surface clean. To produce evenly cooked, perfectly

braised products, keep the pan surface free from carbonized grease. Carbonized grease on the surface

hinders the transfer of heat from the pan surface to the food. This results in spotty browning and loss

of cooking eciency. Worst of all, carbonized grease tends to cling to the foods, giving them a highly

unsatisfactory and unappetizing appearance.

After Each Use

Clean the pan surface with a brush or exible spatula.

Remove the strainer (Fig. 6) at the pouring lip of the braising pan by pulling it toward the back of the pan.

Clean the strainer in a sink. Rinse thoroughly and dry with a soft, clean cloth. Replace strainer.

Fig. 6

Once a Day

Thoroughly clean the back, sides and front of the pan. Also clean the inside and outside surfaces of the lid.

Once a Week

Clean the pan surface thoroughly. If necessary, use a griddle stone or brush on the surface. A detergent

may be used on the pan surface to help clean it, but be sure the detergent is thoroughly removed.

Clean other stainless steel surfaces with a damp cloth and polish with a soft, dry cloth. To remove

discolorations, use a nonabrasive cleaner. If the braising pan usage is very high, consider going through

the weekly cleaning procedures more often than once a week.

When cleaning the braising pan, it is helpful to ll the pan with approximately 10 gallons (38 L) of warm

water and add detergent. After cleaning, raise the braising pan to drain all water (place a bucket or

container under the pouring lip). Then repeat the procedures for rinsing with clean water.

PL-41753

– 16 –

COOKING GUIDELINES (Domestic Measurements)

The guidelines given below are suggested quantities, temperature settings and estimated numbers of

orders per load and per hour. When two temperatures are given, the rst is to start the product and the

second is to nish the product.

The following temperatures should be used:

Temperature

(°F)

Simmering 200 Max.

Sautéing 225 to 275

Searing 300 to 350

Frying 325 to 375

Grilling 350 to 425

ITEM

PORTION

SIZE

TEMP.

(°F)

BATCHES

PER

HOUR

VG30/VE30

PER LOAD

VG40/VE40

PER LOAD

QTY. PORTIONS QTY. PORTIONS

BREAKFAST FOODS

Bacon 3 Slices 350 12 2 lb. 10 3 lb. 15

Eggs

–Boiled-Hard 1 egg 225 5 50 eggs 50 75 eggs 75

–Boiled-Soft 1 egg 225 8 50 eggs 50 75 eggs 75

–Fried 1 egg 400 4 30 eggs 30 45 eggs 45

–Poached 1 egg 225 5 36 eggs 36 60 eggs 60

–Scrambled 1

/2 eggs 300 – 200 1 18 gal. 720 28 gal. 1100

French Toast 3 slices 425 7 35 slices 12 50 slices 17

Regular Oatmeal

/2 cup 250 2

20 lb (100 cups)

500 40 lb (200 cups) 1000

Pancakes 2 each 400 10 30 ea. 15 50 ea. 25

FISH

Clams 1 pt. 400 10 10 qts. 20 15 qts. 30

Fish Cakes 2 to 3 oz. 400 5 70 – 3 oz. 35 110 – 3 oz. 55

Haddock Fillet 4 oz. 400 4 60 – 4 oz. 60 90 – 4 oz. 90

Halibut Steak 5 oz. 425 3 60 – 4 oz. 60 90 – 4 oz. 90

Lobster 1 – 1 lb. 350 4 20 – 1 lb. 20 30 – 1 lb. 30

Swordsh 5 oz. 425 3 50 – 5 oz. 50 75 – 5 oz. 75

SAUCES, GRAVIES, SOUPS

Brown Gravy 1 oz. 350 – 200 2 30 gal. 3840 40 gal. 5120

Cream Sauce 2 oz. 250 – 175 1 30 gal. 1920 40 gal. 2560

Cream Soup 6 oz. 200 1 30 gal. 640 40 gal. 853

French Onion Soup 6 oz. 225 1 30 gal. 640 40 gal. 853

Meat Sauce 4 oz. 350 – 200 1 30 gal. 960 40 gal. 1280

– 17 –

ITEM

PORTION

SIZE

TEMP.

(°F)

BATCHES

PER

HOUR

VG30/VE30

PER LOAD

VG40/VE40

PER LOAD

QTY. PORTIONS QTY. PORTIONS

VEGETABLES

CANNED 3 oz. 400 6 30 lb. 125 45 lb. 200

FRESH

Beans, Wax, Green 3 oz. 400 3 25 lb. 125 50 lb. 250

Beets 3 oz. 400 1 30 lb. 125 60 lb. 300

Broccoli 3 oz. 400 3 25 lb. 125 40 lb. 200

Cabbage 3 oz. 400 5 20 lb. 80 30 lb. 125

Carrots 3 oz. 400 2 35 lb. 150 70 lb. 300

Cauliower 3 oz. 250 5 15 lb. 75 25 lb. 125

Corn 1 Ear 400 8 50 ears 50 75 ears 75

Potatoes 3 oz. 400 2 40 lb. 200 60 lb. 300

Spinach 4 oz. 250 10 6 lb. 25 9 lb. 35

Turnips 4 oz. 400 2 20 lb. 100 30 lb. 150

FROZEN

Beans, French Green 3 oz. 400 6 15 lb. 60 22

/2 lb. 90

Lima Beans 3 oz. 250 4 15 lb. 60 22

/2 lb. 90

Broccoli 3 oz. 400 8 12 lb. 50 18 lb. 75

Sliced Carrots 3 oz. 250 6 15 lb. 60 22

/2 lb. 90

Small Whole Carrots 3 oz. 250 3 15 lb. 50 22

/2 lb. 90

Corn 3 oz. 250 18 15 lb. 50 22

/2 lb. 90

Small Whole Onions 3 oz. 250 7 15 lb. 50 22

/2 lb. 90

Peas 3 oz. 400 10 15 lb. 75 22

/2 lb. 110

Spinach 3 oz. 400 3 15 lb. 75 22

/2 lb. 110

DESSERTS, PUDDINGS, SWEET SAUCES

Butterscotch Sauce 1 oz. 200 1 30 gal. 3840 40 gal. 5120

Cherry Cobbler 3 oz. 200 1 30 gal. 1280 40 gal. 1707

Chocolate Sauce 1 oz. 200 1 30 gal. 3840 40 gal. 5120

Cornstarch Pudding 4 oz. 200 1 30 gal. 960 40 gal. 1280

Fruit Gelatin 3 oz. 250 2 30 gal. 1280 40 gal. 1707

MEAT – POULTRY

Bacon 3 Slices 350 12 2 lb. 10 3 lb. 15

BEEF

Amer. Chop Suey 6 oz. 400 – 225 2 30 gal. 640 40 gal. 853

Beef Stew 8 oz. 300 — 30 gal. 480 40 gal. 640

Corned Beef Hash 5 oz. 400 5 20 lb. 60 30 lb. 90

Cheeseburger 3 oz. 300 12 7 lb. 35 10 lb. 50

Hamburger 3 oz. 300 15 7 lb. 35 10 lb. 50

Meatballs 1 oz. 400 – 225 3 12

/2 lb. 65 18 lb. 100

Pot Roast 2 oz. 350 – 200 120 lb. 500 180 lb. 750

Salisbury Steak 5 oz. 400 3 16 lb. 50 24 lb. 75

Sirloin Steak 6 oz. 400 5 15 lb. 40 22

/2 lb. 60

Swiss Steak 4 oz. 300 – 200 1 25 lb. 110 40 lb. 160

– 18 –

ITEM

PORTION

SIZE

TEMP.

(°F)

BATCHES

PER

HOUR

VG30/VE30

PER LOAD

VG40/VE40

PER LOAD

QTY. PORTIONS QTY. PORTIONS

CHICKEN

Pan Fried 2 –

/4's 350 3 50 pieces 25 80 pieces 40

Whole 2 oz. 350 – 200 16 – 5 lb. 200 24 – 5 lb. 265

FRANKFURTERS

Grilled 2 oz. 300 8 22 lb. 176 33 lb. 264

Boiled 2 oz. 250 12 16 lb. 128 25 lb. 200

PORK

Ham Steak 3 oz. 400 8 10 lb. 50 15 lb. 75

Pork Chops 5 oz. 350 4 15 lb. 50 25 lb. 75

Sausage Links 3 links 350 7 30 lb. 120 45 lb. 180

TURKEY

O Carcass 2 oz. 400 – 200 — 3–26 to 30 lb. 200 4–26 to 30 lb. 275

On Carcass 2 oz. 400 – 200 — 4–16 to 20 lb. 175 6–16 to 20 lb. 265

MISCELLANEOUS

Grilled Cheese Sandwich 1 sand. 400 8 40 sand. 40 50 sand. 50

Macaroni & Cheese 8 oz. 200 2 30 gal. 480 40 gal. 640

Rice 4 oz. 350 – 225 1 20 lb. raw 320 40 lb. raw 650

Spaghetti 4 oz. 350 – 225 2 8 lb. raw 200 12 lb. raw 300

– 19 –

COOKING GUIDELINES (Metric Measurements)

The guidelines given below are suggested quantities, temperature settings and estimated numbers of

orders per load and per hour. When two temperatures are given, the rst is to start the product and the

second is to nish the product.

The following temperatures should be used:

Temperature (°C)

Simmering 93.3 Max.

Sautéing 107 to 135

Searing 149 to 177

Frying 163 to 191

Grilling 177 to 218

ITEM

PORTION

SIZE

TEMP.

(°C)

BATCHES

PER

HOUR

VG30/VE30

PER LOAD

VG40/VE40

PER LOAD

QTY. PORTIONS QTY. PORTIONS

BREAKFAST FOODS

Bacon 3 Slices 177 12 0.9 kg 10 1.4 kg 15

Eggs

–Boiled-Hard 1 egg 107 5 50 eggs 50 75 eggs 75

–Boiled-Soft 1 egg 107 8 50 eggs 50 75 eggs 75

–Fried 1 egg 204 4 30 eggs 30 45 eggs 45

–Poached 1 egg 107 5 36 eggs 36 60 eggs 60

–Scrambled 1

/2 eggs 149 – 93 1 68 L 720 106 L 1100

French Toast 3 slices 218 7 35 slices 12 50 slices 17

Regular Oatmeal 118 mL 121 2 9 kg 500 18 kg 1000

Pancakes 2 each 204 10 30 ea. 15 50 ea. 25

FISH

Clams 473 mL 204 10 9 L 20 14 L 30

Fish Cakes 57 to 85 g 204 5 70 – 85 g 35 110 – 85 g 55

Haddock Fillet 113 g 204 4 60 – 113 g 60 90 – 113 g 90

Halibut Steak 142 g 218 3 60 – 113 g 60 90 – 113 g 90

Lobster 1 – 0.5 kg 177 4 20 – 0.5 kg 20 30 – 0.5 kg 30

Swordsh 142 g 218 3 50 – 142 g. 50 75 – 142 g 75

SAUCES, GRAVIES, SOUPS

Brown Gravy 28 g 177 – 93 2 114 L 3840 151 L 5120

Cream Sauce 57 g 121 – 79 1 114 L 1920 151 L 2560

Cream Soup 170 g 93 1 114 L 640 151 L 853

French Onion Soup 170 g 107 1 114 L 640 151 L 853

Meat Sauce 113 g 177 – 93 1 114 L 960 151 L 1280

– 20 –

ITEM

PORTION

SIZE

TEMP.

(°C)

BATCHES

PER

HOUR

VG30/VE30

PER LOAD

VG40/VE40

PER LOAD

QTY. PORTIONS QTY. PORTIONS

VEGETABLES

CANNED 85 g 204 6 14 kg 125 20 kg 200

FRESH

Beans, Wax, Green 85 g 204 3 11 kg 125 23 kg 250

Beets 85 g 204 1 14 kg 125 27 kg 300

Broccoli 85 g 204 3 11 kg 125 18 kg 200

Cabbage 85 g 204 5 9 kg 80 14 kg 125

Carrots 85 g 204 2 16 kg 150 32 kg 300

Cauliower 85 g 121 5 7 kg 75 11 kg 125

Corn 1 Ear 204 8 50 ears 50 75 ears 75

Potatoes 85 g 204 2 18 kg 200 27 kg 300

Spinach 113 g 121 10 3 kg 25 4 kg 35

Turnips 113 g 204 2 9 kg 100 14 kg 150

FROZEN

Beans, French Green 85 g 204 6 7 kg 60 10 kg 90

Lima Beans 85 g 121 4 7 kg 60 10 kg 90

Broccoli 85 g 204 8 5 kg 50 8 kg 75

Sliced Carrots 85 g 121 6 7 kg 60 10 kg 90

Small Whole Carrots 85 g 121 3 7 kg 50 10 kg 90

Corn 85 g 121 18 7 kg 50 10 kg 90

Small Whole Onions 85 g 121 7 7 kg 50 10 kg 90

Peas 85 g 204 10 7 kg 75 10 kg 110

Spinach 85 g 204 3 7 kg 75 10 kg 110

DESSERTS, PUDDINGS, SWEET SAUCES

Butterscotch Sauce 28 g 93 1 114 L 3840 151 L 5120

Cherry Cobbler 85 g 93 1 114 L 1280 151 L 1707

Chocolate Sauce 28 g 93 1 114 L 3840 151 L 5120

Cornstarch Pudding 113 g 93 1 114 L 960 151 L 1280

Fruit Gelatin 85 g 121 2 114 L 1280 151 L 1707

MEAT – POULTRY

Bacon 3 Slices 177 12 0.9 kg 10 1 kg 15

BEEF

Amer. Chop Suey 170 g 204 – 107 2 114 L 640 151 L 853

Beef Stew 0.2 kg 149 — 114 L 480 151 L 640

Corned Beef Hash 142 g 204 5 9 kg 60 14 kg 90

Cheeseburger 85 g 149 12 3 kg 35 5 kg 50

Hamburger 85 g 149 15 3 kg 35 5 kg 50

Meatballs 28 g 204 – 107 3 6 kg 65 8 kg 100

Pot Roast 57 g 177 – 93 54 kg 500 82 kg 750

Salisbury Steak 142 g 204 3 7 kg 50 11 kg 75

Sirloin Steak 170 g 204 5 7 kg 40 10 kg 60

Swiss Steak 113 g 149 – 93 1 11 kg 110 18 kg 160

La page charge ...

Vulcan VG30 Manuel utilisateur

Marque: Vulcan

Modèle: VG30

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Vulcan VG30 User manual

Vulcan VG30 Manuel utilisateur

Vulcan VG30 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents