Uniden SX507-2CKHS Manuel utilisateur

Marque: Uniden

Modèle: SX507-2CKHS

Catégorie: Radios bidirectionnelles

Taper: Manuel utilisateur

SX507

Radio color/pattern varies

according to model number.

*Range may vary depending on environmental

and/or topographical conditions.

• 7 Weather Channels

• 142 Privacy Codes (CTCSS

Tone and DCS Code)

• Up to 50 Mile Range*

• Internal VOX Circuitry

• TRU Waterproof™ (IPX7/

JIS7) — Submersible and

Floats

• Direct Call with Name

Display

• 143 Group Codes

• Silent Mode

• 10 Selectable Call/Ring Tone

Alerts

• Backlit LCD Display

• Roger Beep

• Call Alert; Vibrate

• 2 Earbuds with VOX Mic or 2

Headset Boom Mics

(depending on model

number) per radio

1 Antenna 9 Charging Contacts

2 Push to Talk 10 MicroUSB port and

earbud jack

3 Boost (Change

transmission power

from 1.0W to 2.5W.)

11 Volume (UP/DOWN)

4 Channel UP/DOWN 12 Enter/Lock

5 Menu/Power 13 Tone/Group

6 D Call 14 WX Alert

7 Light/MON 15 Microphone

8 Speaker

Congratulations on your purchase of a Uniden

SX507 series radio. This lightweight, palm-sized

radio is a state-of-the-art device, equipped with

many valuable features. Use it at sporting

events, to stay in contact with family and friends,

hiking, skiing, outdoors, or in a neighborhood

watch for vital communication.

Your radio complies with IPX7/JIS7 water-

resistant standards, which means the radio

can be submerged in 3.3 feet (1.0 meters) of

water for 30 minutes without damage.

• The radio will only meet this rating if fully

assembled and all rubber seals and the jack

cover are well maintained and correctly fitted.

This means that the Headset plug is not

inserted, and the Headset jack cover and the

battery pack are attached and securely

fastened.

• After your radio is submerged in water, you

might notice that the sound is distorted. This is

because water remains in and around the

speaker and microphone. Just shake the radio

to clear excess water, and the sound should

return to normal.

Note: If your radio is exposed to salt water,

clean your radio thoroughly with fresh water

and dry it before turning it on.

PACKAGE CONTENTS

Each radio uses 3 rechargeable 1000mAH AA

Ni-MH batteries, included.

If your model number contains a "C," your

package contains a microUSB Y charging cable.

If your model number contains "CK," it contains a

charging kit (including a charging cradle).

If your models number contains "HS," it contains

headsets.

Refer to the packaging for other specific

contents.

INSTALL THE BATTERY

These radios each use 3 rechargeable 1000mAH

AA batteries for power (included).

1. Remove the belt clip if necessary.

2. Turn the screw holding the battery

compartment counterclockwise with a

screwdriver and lift up the battery cover,

3. Insert the NiMH batteries in the battery

compartment according to the directions

inside the case. Installing the batteries

incorrectly will prevent the unit from operating.

4. Before placing the battery cover back on the

radio, check the rubber seal around the

battery compartment. Make sure that the seal

is in good condition and that there is no

foreign matter under it.

5. Replace the battery compartment door.

Tighten the screws securely.

6. Replace the belt clip if necessary.

Note: If the rubber seal appears worn, nicked,

or dried out, replacement seals are available

from www.uniden.com.

CHARGING THE RADIO

Follow these instructions to charge or recharge

your radios.

Make sure to turn the radio OFF before

placing it in the charging cradle.

1. Insert the adapter's microUSB plug to DC IN

5V USB jack of the charging cradle and plug

the other end into an AC outlet.

2. Set the charging cradle on a stable desk or

tabletop and place the radios in the charging

cradle with the keypad facing forward.

3. Make sure that the LED illuminates. Charge

the batteries for 16 hours and remove the

radio from the charging cradle after charging.

Note:

• Use only the supplied batteries and AC

adapter or approved accessories from

Uniden.

• The batteries must be installed for the unit to

operate, even if the unit is also connected to

external power.

• If battery power is low, you cannot operate

the radio even using external power. Allow

the batteries to charge before using. If you try

to transmit while power is low, the radio will

automatically turn off.

• Charge time may vary depending on the

battery life remaining.

• For faster charging, turn off the radio before

charging.

Warning!

• The charging cradle is not waterproof. If the

charging cradle falls in the water, unplug it

before attempting to remove it from the water.

Allow the cradle to dry completely before

reconnecting the power.

• Wipe off dirt or shake water from your radio

before placing in the charging cradle if your

radio is soiled or wet.

USING A HEADSET

Depending on the model number, your radios

may come with an earbud headset with mic on

the cord or with a boom mic headset. To use a

headset, lift the rubber cover from over the

headset jack, then plug in the headset.

Important: Your radio is not waterproof when

using a headset jack. When you remove the

headset, be sure to fully press the jack cover

into place to restore its waterproof capability.

• Set a "Nickname."

Setting the Radio to Group Mode

To set the radio to Group mode, which enables

Direct Call, Auto Channel Change, and All Call,

press and hold TONE/GROUP for 2 seconds.

The radio displays GRP and group code.

Note: In Group mode, you cannot receive

transmissions from other radios unless

they are also set to the same channel and

group code.

Setting the Group Code

Set the group code for your radio group from

0-142. Everyone in your group must select the

same group code in order to communicate with

each other.

1. PressTONE/GROUP in Group mode. Press

CH or to select the group number.

2. Press ENTER/LOCK or TONE/GROUP to

return to normal operation.

Setting the Unit Number

Each radio in your group needs to be set to a

unique unit number, from 1-16.

1. Press MENU/ . Advance through the menu

until UNIT appears, and then press ENTER/

LOCK. The current unit number flashes.

2. Press CH or to select the desired unit

number.

3. Press ENTER/LOCK to continue to the next

section.

Setting Your Nickname

Your nickname appears on other units’ displays

when you make an All Call or Direct Call. This is

also the name that appears on other radio

displays when someone wants to make a Direct

Call to you. Without a nickname, the unit

number shows.

1. Press MENU/ and advance through the

menu until UNIT appears; then press

ENTER/LOCK. The current unit number

flashes, then press ENTER/LOCK The radio

displays

- - - -

(or your current nickname)

with the first place in the nickname flashing.

2. Press CH or to select the letter, then

ENTER/LOCK to advance to the next letter

until you have entered your nickname.

3. Press MENU/ to confirm the setting and

exit the menu.

Using Group Mode

Group mode lets you make direct calls to other

people in your group without alerting the entire

group and also lets you quickly change

everyone in your group to another channel from

a single radio. Before using Group mode, follow

the instructions in "Setting Up Group mode" on

every radio in your group. Then, to record the

unit ID and everyone’s nickname in every radio,

send a call to "All" from each radio one time

(see "Sending a Direct Call").

Sending a Direct Call

Direct Call lets you call everyone in your group

at once, or call a single person in your group

without anyone else in the group knowing. It is

like a "speed dial" directly to the person(s) you

want to talk to.

To call everyone in your group, press D CALL in

Group mode. The radio flashes ALL. Then,

press D CALL or ENTER/LOCK Everyone in

your group receives a call "chirp" for about 3

seconds. When the chirp ends, begin your

conversation.

Note: When you make a direct call to "all," your

radio also sends out your nickname or ID so

that it will show up in the call list for everyone in

your group.

To call one person in your group without having

other people know, press D CALL in Group

mode. Then, use CH or to select the

person you want to call and press D CALL or

ENTER/LOCK. Your radio sounds tones for 3

seconds as it sends the call. When the selected

person answers, you can begin your

conversation.

You can silence the call tones any time by

pressing PTT or BOOST.

Your conversation remains private between you

and the person you called until 15 seconds after

your last conversation. Then, your radio

automatically exits Private mode.

Automatically Changing Channels

Auto Channel Change lets you easily coordinate

a channel change for everyone in your group.

You might want to do this when you find you are

getting a lot of interference on your current

channel. You also use this feature to change

from a low-power channel (8-14) to one of the

high-powered channels (1-7, 15-22) for more

range (or to a low-power channel if you need

longer battery life).

To start an auto channel change, on any radio

in the group, press MENU/ . Advance through

the menu until CHCX appears, then press

ENTER/LOCK. The current channel flashes.

Use CH or to select the target channel.

You can check whether the selected channel is

clear. Then press D CALL or ENTER/LOCK.

Your radio chirps for about 10 seconds while it

sends out the channel change signal. As each

radio receives the channel change signal, it

chirps once, then changes to the new channel.

To ensure all radios make it to the new channel,

we recommend you:

cutting off the first part of your transmission,

pause slightly after pressing PTT or BOOST

before you start talking.

2. When you finish speaking, release PTT or

BOOST. You can now receive incoming calls.

While receiving, RX appears on the display.

Note:

• When you press BOOST, BOOST appear on

the display.

• If BOOST, PTT or VOX is continuously used,

1 minute after you start using the feature the

transmission stops and you hear a timeout

error tone.

Monitor Mode Feature

Your radio lets you listen for weak signals on

the current channel at the press of a key.

To turn on the Monitor mode:

• Press and hold LIGHT/MON for 2 seconds

until two beeps sound for continuous

listening. The receiver circuit stays open, so

you hear both the noise and weak signals.

To turn off Monitor mode:

Press LIGHT/MON to return to the previous

mode. MON and RX disappear.

Navigating through the Normal Menu

Your radio has a Menu function to access

advanced features. In order to use Auto

Channel Change, you need to set your radio to

Group mode.

Start

Scanning

Scan

Mode

Silent

Mode

ON-OFF

Auto

Channel

Change

Channel

Change

VOX

Level

OFF, 1-5

1-10

Call

Tone

Unit

Setting

Unit

Number

Roger

Beep

ON-OFF

Beep

Tone

ON-OFF

Setting

Nickname

1. To enter the menu, press MENU/ .

2. Press MENU/ again to advance through

the menu. After the last menu item, the radio

exits to the previous mode.

3. Other ways to exit the Menu function are:

a. Press PTT, BOOST, LIGHT/MON, D

CALL, WX/ALERT or TONE/GROUP.

b. Wait 10 seconds until the radio

automatically returns to the previous

mode.

Setting Silent Mode

When you turn on Silent mode, all incoming

calls are muted, the display backlight flashes,

and the channel indicator displays SLNT and

CALL to alert you to an incoming call. If you do

not respond to the call within 15 seconds, the

backlight turns off. The radio will also vibrate to

remind you that you missed a call. Silent mode

is disabled for 15 seconds when you transmit,

receive, or press any other button.

To set Silent mode:

1. Enter the menu. Advance through the menu

until the SLNT displays, then press ENTER/

LOCK. The current setting flashes.

2. Press

to display on, then press

ENTER/

LOCK.

Note: To prevent unwanted silent alerts, be sure

to use a Privacy Code or Group Code whenever

you use the Silent mode feature.

You can hear the received voice when you turn

on channel scan and an active channel is

detected, even during Silent mode.

Missed Call Alerts

If you receive an incoming call while Silent

mode is on and do not respond, the radio will

turn on the Missed Call icon. If you are using

Group mode, the radio will also indicate who

made the call.

The radio also remind you of a missed call by

vibrating every minute after the call for 3

minutes.

Voice Operated Transmission

Your radio is equipped with a user selectable

Voice Operated Transmitter (VOX) that can be

used for automatic voice transmissions. The

VOX feature is designed to be used with a

headset with a microphone. Initiate transmission

by speaking into the remote microphone instead

of pushing PTT and BOOST. To select the VOX

level:

1. Press MENU/ . Advance through the Menu

until VOX appears on the display, then press

ENTER/LOCK. The current level (off, 1-5)

flashes. Level oF (off) disables VOX, while

levels 1-5 set the sensitivity of the VOX

circuit.

2. Press either CH or to reach the

desired VOX sensitivity level, then press

ENTER/LOCK. Use level 1 for increased

sensitivity to voice in normally quiet

environments, and use a higher level to

reduce undesired activation in very noisy

environments.

Transmitting a Call Tone

Your radio is equipped with 10 selectable call

tones that are transmitted when you press D

CALL in Standard mode.

The selected tone also will be heard when

• BOOST for Maximum

Range*

• Headset Jack

• Auto Channel Change

Call

• Battery Level Meter

• Rechargeable NiMH

Batteries

• Dual Charging Cradle

with AC Adapter

• Channel Monitor

• Channel Scan

Group Scan

• Keypad Lock

• Emergency Weather

Alert

• Emergency Light

• Last Channel Memory

• Carabiner clip (1 per

radio)

• Make sure you are in an open environment,

where the radio will get the best range.

• Optimize range during the channel change

signal by raising the radio over your head to

give the best possible height.

• Do a "roll call" on the new channel after the

move to be sure no one was left behind. If

you missed someone, return to the previous

channel and issue the signal again.

USING THE RADIO IN

STANDARD MODE

Use the radio in Standard (not Group) mode

when you need to be able to communicate with

radios that do not have the group feature.

Choosing a Privacy Code

You can select a Privacy Code from 1-142 for

each channel. oF (off) indicates no Privacy

Code selected and your radio can receive a

signal regardless of the code settings of the

transmitting radio.

1. Press TONE/GROUP. The Privacy Code

indicator flashes.

2. Press CH or to increase or decrease

the code. You can also select oF.

3. Press ENTER/LOCK or TONE/GROUP to

return to normal operation.

Note: Only tones 1-38 are standard across

radio brands. Other settings might differ

from brand to brand. See the specifications

for the specific tones used for each setting.

Channel Scan Feature

Your radio has a channel scan feature that lets

you easily scan all 22 channels. When an active

channel is detected, the radio pauses on that

channel until the channel is clear. Then after a

2-second delay, the radio resumes scanning.

Pressing PTT or BOOST while the scan is

paused on a channel lets you transmit on that

channel.

To turn on channel scan:

Press MENU/ . The radio displays SCAN.

Press ENTER/LOCK. The channel number

changes as the radio rapidly cycles through the

channels.

Use the radio in Standard (not Group) mode

when you need to be able to communicate with

radios that do not have the group feature.

Talking on Your Radio

To talk to others using the radio:

1. Press and hold PTT or BOOST and speak in

a clear, normal voice about 2-3 inches away

from the microphone. While you transmit,

TXHI or TXLO appears on the display

according to the type of channel. To avoid

someone places a direct call to you.

To select a call tone:

1. Press MENU/ . Advance through the menu

until CALL appears, then press ENTER/LOCK.

The current call tone number (1-10) flashes.

Press CH or to increase or decrease the

number to the desired call tone. Each tone will

be heard through the speaker. Press ENTER/

LOCK to select a call tone.

To transmit the selected call tone, press D CALL.

The selected tone is transmitted for a fixed length

of time. Press PTT or BOOST to cancel.

Roger Beep

Roger Beep is a beep that is sent to notify the end

of transmission (both PTT and VOX transmission).

You can hear Roger Beep through the speaker

when both Roger Beep and Beep Tone are on.

When Roger Beep is on and Beep Tone is off, you

do not hear Roger Beep, but it is transmitted to

your party.

To adjust Roger Beep, press MENU/ . Advance

through the menu until RGR appears, then press

ENTER/LOCK. The current setting flashes.

To turn off Roger Beep:

Press CH to display oF, then press ENTER/

LOCK.

To turn on Roger Beep:

Press CH to display on, then press ENTER/

LOCK.

Adjusting the Sound (Beep Tone)

Your radio sounds a beep each time you press a

key (except for PTT and BOOST).

To adjust the sound, press MENU/ . Advance

through the menu until TONE appears, then press

ENTER/LOCK. The current setting flashes.

To turn off the beep:

Press CH to display oF, then press ENTER/

LOCK.

To turn on the beep:

Press CH to display on, then press ENTER/

LOCK.

Key Lock

Press and hold the ENTER/LOCK until LOCK

appears.

To turn Keylock off, press and hold ENTER/LOCK

again.

Note:

• If Keylock is on, the radio can still receive

transmissions. Use D CALL in Standard mode,

VO or , PTT, BOOST, LIGHT/MON, and

MENU/ to turn the radio on or off.

USING RADIO BATTERY

LEVEL AND LOW BATTERY

ALERT

This radio has a battery level meter that

indicates the battery power level. When the

battery level is low, the battery level meter icon

flashes and then BATT appears after 30

seconds. Recharge the NiMH batteries

immediately.

Warning! To avoid the risk of personal injury or

property damage from fire or electrical shock,

only use the Uniden accessories specifically

designated for this product.

USING THE RADIO

In order to get the most out of your new radio,

read this reference guide completely before

attempting to operate it.

Turning the Radio On and Adjusting

the Volume

1. Press and hold MENU/ to turn the radio

on.

2. Press VO or to increase or decrease

the volume level then press ENTER/LOCK.

3. Press and hold MENU/ to turn the radio

off.

Choosing a Channel

Your radio has 22 channels and 142 Privacy

codes you can use to talk to others. In order to

speak to someone, both your radios must be set

to the same channel and Privacy code.

To choose a channel:

Press CH or , then press CH or to

increase or decrease the channel number

displayed.

To scroll through the channels, press CH or

, then press and hold CH or for more

than 1 second.

Note: Channels 1-7 and 15-22 have a typical

range of up to 50 miles by pressing BOOST.

HI displays when you select one of these

channels, and LO displays when you select

channel 8 - 14.

SETTING UP GROUP MODE

Group mode lets several people talk on the

same channel in a separate group. In order to

use Group mode, you need to initialize specific

settings in your radio:

• Set the radio to Group mode.

• Set a Group Code.

• Set a Unit Number.

• The radio retains the keylock status even when

you cycle power.

Using the Flashlight

You can use this radio in an emergency. If you

press LIGHT/MON, the radio turns on the high-

intensity LED flashlight on your radio. Depending

on how you set it up, the LED functions as a

flashlight, flashes “S O S” in international Morse

Code, is always on, or is off.

Note: Your radio operates normally when the

SOS strobe is activated.

1. Press LIGHT/MON while this light is turned off,

the Strobe Light emits the SOS signal. (Strobe

SOS mode)

2. And then, press LIGHT/MON once more, it will

turn on continuously. (Always On mode)

3. And then, press LIGHT/MON while Always On

mode, the light will be turned off.

Automatic Power Save Feature

Your radio has a unique circuit designed to

dramatically extend the life of the battery. If you do

not transmit and do not receive an incoming call

within 3 seconds, your radio switches to the Power

Save mode. The radio is still able to receive

transmissions in this mode.

LCD Backlight

The LCD Backlight automatically turns on when any

key (except for PTT and BOOST) is pressed. The

LCD remains lit for 10 seconds before turning off.

USING THE WEATHER RADIO

Your radio can receive weather broadcasts from the

NOAA National Weather Service. When in Weather

Radio Alert mode, the system functions as it does

in Standard mode or Group mode but also monitors

the selected weather channel for alerts when not

communicating.

1. To turn on the Weather Radio Broadcast mode,

press WX/ALERT. WX appears.

2. Press CH or to increase or decrease the

number to the desired Weather Channel.

3. To exit the Weather Radio Broadcast mode,

press WX/ALERT. WX disappears.

When in the Weather Radio Broadcast mode, you

can only set the Beep Tone from the Menu mode.

Choosing an Emergency/Weather Channel

There are 7 NOAA channel frequencies available

and these frequencies are common between the

US and Canada. You need to know what frequency

is being transmitted in your location.

1. Press and hold WX/ALERT. appears.

2. When the unit receives a warning signal, it

beeps for 5 seconds. and channel indicator

flash.

3. To turn off Weather Alert, press and hold

WX/ALERT. disappears.

• When Weather Alert is activated, the highest

priority is given to this function. It checks the

weather alert signals every 7 seconds. When the

unit finds a warning signal, it switches to the

Warning Receive mode automatically.

• Weather Alert is activated even if Beep Tone is

off.

NOAA Weather Radio Frequency List:

Chan. Freq.

(MHz)

Chan. Freq.

(MHz)

1 162.550 5 162.450

2 162.400 6 162.500

3 162.475 7 162.525

4 162.425

SPECIFICATIONS

Item Specication

Channels 22 + 7 Weather

Privacy Codes 38 Sub-Codes

83 DCS Codes

Operating Frequency (MHz)

FRS:

462.5500 - 467.7125

WX:

162.4000 - 162.5500

Power Source Per radio: 3 AA NiMH Batteries

(1000 mAh)

Range (Chan.) 50 Miles

1-7

Up to 18 (up to 50 with BOOST)

8-14

Up to 5

15-22

Up to 18 (up to 50 with BOOST)

Battery Life

(Hours)

8.5 Hours (typical) -- AA NiMH

Batteries (5/5/90 duty cycle)

FREQUENCIES

Frequency Chart

CHANNEL Frequency CH. Frequency.

1 462.5625 12 467.6625

2 462.5875 13 467.6875

3 462.6125 14 467.7125

4 462.6375 15 462.5500

5 462.6625 16 462.5750

CHANNEL Frequency CH. Frequency.

6 462.6875 17 462.6000

7 462.7125 18 462.6250

8 467.5625 19 462.6500

9 467.5875 20 462.6750

10 467.6125 21 462.7000

11 467.6375 22 462.7250

CTCSS & DCS CODES

CTCSS Chart (Hz)

Code Freq. Code Freq. Code Freq.

oF OFF 13 103.5 26 162.2

1 67.0 14 107.2 27 167.9

2 71.9 15 110.9 28 173.8

3 74.4 16 114.8 29 179.9

4 77.0 17 118.8 30 186.2

5 79.7 18 123.0 31 192.8

6 82.5 19 127.3 32 203.5

7 85.48 20 131.8 33 210.7

8 88.5 21 136.5 34 218.1

9 91.5 22 141.3 35 225.7

10 94.8 23 146.2 36 233.6

11 97.4 24 151.4 37 241.8

12 100.0 25 156.7 38 250.3

DSC Code List

Tone

No.

Octal

Code

Tone

No.

Octal

Code

Tone

No.

Octal

Code

39 023 67 174 95 445

40 025 68 205 96 464

41 026 69 223 97 465

42 031 70 226 98 466

43 032 71 243 99 503

44 043 72 244 100 506

45 047 73 245 101 516

46 051 74 251 102 532

47 054 75 261 103 546

48 065 76 263 104 565

49 071 77 265 105 606

50 072 78 271 106 612

51 073 79 306 107 624

52 074 80 311 108 627

53 114 81 315 109 631

54 115 82 331 110 632

Tone

No.

Octal

Code

Tone

No.

Octal

Code

Tone

No.

Octal

Code

55 116 83 343 111 654

56 125 84 346 112 662

57 131 85 351 113 664

58 132 86 364 114 703

59 134 87 365 115 712

60 143 88 371 116 723

61 152 89 411 117 731

62 155 90 412 118 732

63 156 91 413 119 734

64 162 92 423 120 743

65 165 93 431 121 754

66 172 94 432

MAINTENANCE

To be safe and sure:

• Never open your radio’s case.

• Never change or replace anything in your

radio except the batteries.

Care and Safety

To clean the radio, use a soft cloth dampened

with water. Do not use cleaners or solvents

because they can harm the body of the unit and

leak inside, causing permanent damage. Use a

dry, lint-free cloth to clean the battery contacts.

Do not submerge the unit in water. If the unit

gets wet, turn it off and remove the batteries

immediately.

Dry the battery compartment with a soft cloth to

minimize potential water damage. Leave the

battery compartment cover off overnight to

ensure complete drying. Do not use the radio

until the unit is completely dry.

Your radio might cause TV or radio interference

even when it is operating properly. To determine

whether your radio is causing the interference,

turn it off. If the interference goes away, your

radio is causing it. Try to eliminate the

interference by moving your radio away from the

receiver. If you cannot eliminate the interference,

the FCC requires that you stop using the radio.

Hazardous Environments

Do not operate the radio in hazardous

environments. Explosion or fire may result. Do

not operate the radio near unshielded electrical

blasting caps.

Under certain conditions, radios can interfere

with blasting operations and may cause an

explosion. Turn your radio OFF to prevent

accidental transmission when in a blasting area or

in areas posted: "Turn off two-way radio."

Construction crews often use remote control RF

devices to set off explosives.

WARNING! Read this information before using the

radio. In August 1996 the Federal Communications

Commission (FCC) of the United States with its

action in Report and Order FCC 96-326 adopted an

updated safety standard for human exposure to

radio frequency electromagnetic energy emitted by

FCC regulated transmitters.

Those guidelines are consistent with the safety

standard previously set by both U.S. and

international standards bodies. The design of the

radio complies with the FCC guidelines and these

international standards.

Never allow children to operate the radio without

adult supervision and the knowledge of the

following guidelines.

WARNING! It is up to the user to properly operate

this radio transmitter to insure safe operation.

Please adhere to the following:

Do not use the radio with a damaged antenna. If a

damaged antenna comes into contact with the skin,

a minor burn may result. Please contact your local

dealer for a replacement antenna.

REGULATORY INFORMATION

Hand-Held Operation (Held-to-Face)

This device was evaluated for typical hand-held

(held-to-face) operations with a 1 inch spacing from

the front of the radio. For hand-held operation, the

radio should be held 1 inch from the user's face in

order to comply with FCC RF exposure

requirements.

Body-Worn Operation

This device was evaluated for body-worn

operations with the supplied belt-clip accessory.

(All necessary accessories are included in the

package; any additional or optional accessories are

not required for compliance with the guidelines.)

Third party accessories (unless approved by the

manufacturer) should be avoided as these might

not comply with FCC RF exposure guidelines.

For body worn operation, this device has been

tested and meets the Industry Canada RF exposure

guidelines when used with Uniden accessories

supplied or designated for this product. Use of

other accessories may not ensure compliance with

Industry Canada RF exposure guidelines.

Fonctionnement de l’appareil, lorsque porté sur le

corps. Cet appareil a été testé et s’est avéré

conforme aux normes d’Industrie Canada et

approuvé pour le port sur le corps à l’aide des

accessoires Uniden inclus et conçus pour cet

appareil. L’utilisation d'accessoires ne respectant

pas les exigences d'exposition RF d’Industrie

Canada doit être évitée.

FCC PART15/

IC COMPLIANCE

FCC PART 15 COMPLIANCE

This device complies with Part 15 of the FCC rules.

Operation is subjected to the following two

conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any

interference received, including interference that

may cause undesired operation.

Changes or modifications not expressly approved by

the party responsible for compliance could void your

authority to operate the equipment.

Avis de conformité à la FCC : Ce dispositif a été

testé et s’avère conforme à l’article 15 des

règlements de la Commission fédérale des

communications (FCC). Ce dispositif est soumis aux

conditions suivantes: 1) Ce dispositif ne doit pas

causer d’interférences nuisibles et; 2) Il doit pouvoir

supporter les parasites qu’il reçoit, incluant les

parasites pouvant nuire à son fonctionnement.

Tout changement ou modification non approuvé

expressément par la partie responsable pourrait

annuler le droit à l’utilisateur de faire fonctionner cet

équipement.

IC Compliance

This device complies with Industry Canada license-

exempt RSS standard(s).Operation is subject to the

following two conditions: (1) this device may not

cause interference, and (2) this device must accept

any interference, including interference that may

cause undesired operation of the device.

Changes or modifications not expressly approved by

the party responsible for compliance could void your

authority to operate the equipment.

Cet appareil est conforme aux normes RSS

exemptes de licences d’Industrie Canada. Son

fonctionnement est soumis aux deux conditions

suivantes : (1) cet appareil ne doit pas causer

d’interférences nuisibles et (2), il doit pouvoir

accepter les interférences, incluant celles pouvant

nuire à son fonctionnement normal.

Tout changement ou modification non approuvé

expressément par la partie responsable pourrait

annuler le droit à l’utilisateur de faire fonctionner cet

équipement.

ONE YEAR LIMITED

WARRANTY

Important: Save your receipt! Evidence of

original purchase is required for warranty service.

battery from the Product and separately secure the

battery in its own separate packaging within the

shipping carton. The Product should include all parts

and accessories originally packaged with the Product.

Include evidence of original purchase and a note

describing the defect that has caused you to return

it.The Product should be shipped freight prepaid, by

traceable means, to warrantor at:

Uniden America Service

C/O Saddle Creek

743 Henrietta Creek Road, Suite 100

Roanoke, TX 76262

WARRANTOR: UNIDEN AMERICA

CORPORATION ("Uniden")

ELEMENTS OF WARRANTY: Uniden warrants, for

one year, to the original retail owner, this Uniden

Product to be free from defects in materials and

craftsmanship with only the limitations or exclusions

set out below.

WARRANTY DURATION: This warranty to the

original user shall terminate and be of no further

effect 12 months after the date of original retail

sale. The warranty is invalid if the Product is:

(A) damaged or not maintained as reasonable or

necessary, (B) modified, altered, or used as part of

any conversion kits, sub-assemblies, or any

configurations not sold by Uniden, (C) improperly

installed, (D) serviced or repaired by someone

other than an authorized Uniden service center for

a defect or malfunction covered by this warranty,

(E) used in any conjunction with equipment or parts

or as part of any system not manufactured by

Uniden, or (F) installed or programmed by anyone

other than as detailed by the owner’s manual for

this product.

STATEMENT OF REMEDY: In the event that the

product does not conform to this warranty at any

time while this warranty is in effect, warrantor will

either, at its option, repair or replace the defective

unit and return it to you without charge for parts,

service, or any other cost (except shipping and

handling) incurred by warrantor or its

representatives in connection with the performance

of this warranty. Warrantor, at its option, may

replace the unit with a new or refurbished unit.

THE LIMITED WARRANTY SET FORTH ABOVE IS

THE SOLE AND ENTIRE WARRANTY

PERTAINING TO THE PRODUCT AND IS IN LIEU

OF AND EXCLUDES ALL OTHER WARRANTIES

OF ANY NATURE WHATSOEVER, WHETHER

EXPRESS, IMPLIED OR ARISING BY

OPERATION OF LAW, INCLUDING, BUT NOT

LIMITED TO ANY IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE.THIS WARRANTY DOES

NOT COVER OR PROVIDE FOR THE

REIMBURSEMENT OVERPAYMENT OF

INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow this exclusion or limitation

of incidental or consequential damages so the

above limitation or exclusion may not apply to you.

LEGAL REMEDIES: This warranty gives you

specific legal rights, and you may also have other

rights which vary from state to state. This warranty

is void outside the United States of America and

Canada.

PROCEDURE FOR OBTAINING PERFORMANCE

OF WARRANTY: If, after following the instructions

in the owner’s manual you are certain that the

Product is defective, pack the Product carefully

(preferably in its original packaging). Disconnect the

Uniden SX507-2CKHS Manuel utilisateur

Marque: Uniden

Modèle: SX507-2CKHS

Catégorie: Radios bidirectionnelles

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Uniden SX507-2CKHS User manual

Uniden SX507-2CKHS Manuel utilisateur

Uniden SX507-2CKHS Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents