Tripp Lite SmartPro 3U Rackmount UPS Le manuel du propriétaire

Marque: Tripp Lite

Modèle: SmartPro 3U Rackmount UPS

Catégorie: Alimentations sans interruption (UPS)

Taper: Le manuel du propriétaire

Owner’s Manual

SmartPro

3U Rackmount UPS

Model: SMX5000XLRT3U

(Series Number: AGSM5247)

Not suitable for mobile applications.

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

SmartPro

is a registered trademark of Tripp Lite.

Important Safety ...............2

Instructions

Mounting ..........................3

Quick Installation ..............5

Optional Installation ..........7

Basic Operation ................9

Storage and Service .......13

Battery Replacement ......14

Español...........................16

Français ..........................31





15-12-015- 932460.indb 1 1/19/2016 4:10:01 PM

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains important instructions that should be followed during the

installation, operation and storage of all Tripp Lite UPS Systems. Failure to heed these

warnings may affect your warranty.

UPS Location Warnings

• Use caution when lifting your UPS. Because of the considerable weight of all rackmount UPS

systems, at least two people should assist in lifting and installing them.

• Install your UPS indoors, away from excess moisture or heat, dust or direct sunlight.

• For best performance, the ambient temperature near your UPS should be between 0° C and

40° C (between 32° F and 104° F).

• Leave adequate space around all sides of the UPS for proper ventilation. Do not obstruct its

vents or fan openings.

• Do not mount unit with its front or rear panel facing down (at any angle). Mounting in this

manner will seriously inhibit the unit’s internal cooling, eventually causing product damage not

covered under warranty.

UPS Connection Warnings

• The UPS contains its own energy source (battery). The output terminals may be live even when

the UPS is not connected to an AC supply.

Equipment Connection Warnings

• Use of this equipment in life support applications where failure of this equipment can

reasonably be expected to cause the failure of the life support equipment or to significantly

affect its safety or effectiveness is not recommended. Do not use this equipment in the

presence of a flammable anesthetic mixture with air, oxygen or nitrous oxide.

• Do not connect surge suppressors or extension cords to the output of your UPS. This might

overload the UPS and will void the surge suppressor and UPS warranties.

Battery Warnings

• Batteries can present a risk of electrical shock and burn from high short-circuit current.

Observe proper precautions. Do not dispose of the batteries in a fire. Do not open the UPS or

batteries. Do not short or bridge the battery terminals with any object. Unplug and turn off the

UPS before performing battery replacement. Use tools with insulated handles. There are no

user-serviceable parts inside the UPS. Battery replacement should be performed only by

authorized service personnel using the same number and type of batteries (Sealed Lead-Acid).

The batteries are recyclable. Refer to your local codes for disposal requirements or visit

http://www.tripplite.com/support/recycling-program for recycling information. Tripp Lite offers a

complete line of UPS System Replacement Battery Cartridges (R.B.C.).Visit Tripp Lite on the

Web at http://www.tripplite.com/products/battery-finder/ to locate the specific replacement

battery for your UPS.

• During hot-swap battery replacement, the UPS will not provide backup power in the event of a

blackout or other power interruptions.

• Do not operate UPS without batteries.

• When adding external battery packs connect only Tripp Lite-recommended battery packs of the

correct voltage and type. Do not connect or disconnect battery packs when the UPS is

operating on battery power.

15-12-015- 932460.indb 2 1/19/2016 4:10:01 PM

Mounting

Your UPS may be rackmounted in 4- or 2-post racks. To mount the UPS (power module +

external battery module) in a 2-post rack, purchase the appropriate hardware, sold separately

(order Tripp Lite model # 2POSTRMKITHD). See 2POSTRMKITHD owner’s manual for installation

instructions. To mount the UPS in a 4-post rack, use the included hardware and follow the

procedure outlined below. The procedures are for common rack types and may not be appropriate

for all rack configurations. User must determine the fitness of rackmount hardware and

procedures before mounting.

CAUTION: Rackmount equipment may be extremely heavy—be careful when moving or

lifting equipment. Use one or more assistants if necessary.

4-Post Rack Mounting

Square-Hole Rack Installation

The included plastic pegs

will

temporarily support the empty

rackmount shelves

while you install

the permanent mounting hardware.

Insert a peg near the center of the

front and rear bracket of each shelf as

shown. (Each front bracket has 6 holes

and each rear bracket has 3 holes.)

The pegs will snap into place.

After installing the pegs, expand each shelf to match the depth of your rack rails. The pegs

will fit through the square holes in the rack rails to support the shelves. Refer to the rack unit

labels to confirm that the shelves are level in all directions.

Note: The support ledge of each shelf must face inward.

Secure the shelves

to the mounting

rails permanently using the included

screws and cup washers

as shown.

Place 6 screws total at the front and 4

screws total at the back.

Tighten all screws before proceeding.

Warning: Do not attempt to install

your equipment until you have

inserted and tightened the required

screws. The plastic pegs will not

support the weight of your

equipment.

Attach your equipment’s mounting

brackets to the forward mounting holes

of the cabinet using the hardware

included with your equipment. The

mounting bracket “ears” should face

forward. (Some equipment may have

pre-installed or integral mounting

brackets.)

15-12-015- 932460.indb 3 1/19/2016 4:10:03 PM

With the aid of an assistant (if

necessary), lift your equipment and

slide it into the shelves. Attach the

equipment mounting brackets to the

forward mounting rails with user-

supplied screws and washers

Tighten all screws securely.

Mounting

Threaded-Hole Rack Installation

Align the mounting rail

along the

inside surface of the rack posts

that the flanges on the ends of the rail

wrap around to the front and rear

surfaces of the posts and the rail holes

meet the threaded holes on the rack

post.

Secure the shelves

to the mounting

rails permanently using user-supplied

screws and washers

for your rack as

shown. Place 6 screws total at the

front and 4 screws total at the back.

Tighten all screws before proceeding.

Warning: Do not attempt to install

your equipment until you have

inserted and tightened the required

screws.

Follow steps

and

of the Square-Hole Rack Installation instructions (above) to securely

mount your 3U equipment.

Tower Mounting

If you tower mount this UPS, it requires the addition of a

Tripp Lite 2U to 9U tower stand (model: 2-9USTAND, sold

separately). See owner’s manual for installation

procedure.

Rotate the power module’s Control Panel to view it easier

while the UPS is tower mounted. Insert a small

screwdriver, or other tool, in the slots on either side of the

Control Panel. Pop the panel out; rotate it; and pop the

panel back into place.

15-12-015- 932460.indb 4 1/19/2016 4:10:07 PM

Quick Installation

DANGER!

HIGH VOLTAGE! RISK OF SERIOUS INJURY OR

DEATH! FOR QUALIFIED ELECTRICIANS ONLY!

ELECTRICIANS MUST READ WARNINGS BELOW

AND IN SAFETY SECTION PRIOR TO

INSTALLATION.

connection base step 1

Hardwire the UPS System’s

input terminals to a utility

power source.

Input and Output Ratings

Model Voltage Input Current Output Current Wire Size

SMX5000XLRT3U 230V 27A 30A 10 AWG

Before hardwiring, switch OFF the facility’s circuit breaker which is supplying power to the circuit

the UPS System will be connected to. Using a screwdriver, remove the top of the box

covering

the UPS System’s input terminals. Pass user-supplied cable through the opening in the box

and attach it to the terminals. After hardwiring is complete, switch ON the facility’s circuit breaker

which is supplying power to the circuit the UPS System is connected to. Please note that after the

UPS System is connected to a live utility power source, the UPS (in “Standby” mode) will

automatically charge its batteries,* but will not supply power to its outlets until it is turned ON

(see Step 3 below).

* The BATTERY CHARGE LED will be the only LED illuminated.

Note: UPS system will function properly upon initial startup; however, maximum runtime for the unit’s battery

will only be accessible after it has been charged for 24 hours.

HARDWIRE WARNINGS!

• Wiring must be done by a qualified electrician.

• When making wiring connections, observe the cable connection regulations appropriate to

your area at all times. Be sure to install an easily accessible disconnect switch in your

installation wiring so you may cut off the UPS’s AC input during fires and other

emergencies. Ensure that cables are fitted with cable sleeves and are secured by

connector clamps. Tighten connections with a torque of not less than 10 inch-pounds

(1.1 NM).

• Make sure that your equipment is properly grounded.

• Using cables of improper size may damage your equipment and cause fire hazards.

Choose appropriate cabling and protection circuits to make wiring connections (Ground

conductors must be the same size and type as the power conductors used).

15-12-015- 932460.indb 5 1/19/2016 4:10:07 PM

Quick Installation

Plug your equipment into the

UPS.*

Plug your equipment into the UPS using the

additional power cord(s) that came with the UPS.

Note: Additional interconnection cords (C13 to C14) are

available from Tripp Lite. Visit tripplite.com

(Part # P004-006).

* Your UPS is designed to support only electronic equipment.

You will overload the UPS if the total VA ratings for all the

equipment you connect exceeds the UPS’s Output Capacity.

To find your equipment’s VA ratings, look on their

nameplates. If the equipment is listed in amps, multiply the

number of amps by 230 to determine VA. (Example:

1 amp × 230 = 230 VA). If you are unsure if you have

overloaded the UPS’s outlets, see “OUTPUT LOAD LEVEL”

LED description.

Turn the UPS ON.

Press and hold the “ON/OFF/STANDBY” button for one

second. The alarm will beep once briefly after one

second has passed. Release the button.

15-12-015- 932460.indb 6 1/19/2016 4:10:08 PM

Optional Installation

These connections are optional. Your UPS will function properly without these

connections.

USB and RS-232 Serial Communications

Relay Contact-Closure Connection

Use the included DB9 cable (see

) to connect

specialized electronic equipment to the relay contact-

closure port on your UPS System. See diagram

and

chart below to determine signals carried by this port.

Relay Contact Closure Chart

Line Fail

Indication

Mid Battery

Indication

Low Battery

Indication

UPS Operating

Conditions

Pins

1 & 6

Pins

2 & 6

Pins

7 & 3

Pins

8 & 3

Pins

4 & 9

Pins

5 & 9

AC Input Voltage OK CLOSED OPEN — — — —

AC Input Out of Range OPEN CLOSED — — — —

Battery More than 3

Min. Remaining Charge*

— — OPEN CLOSED — —

Battery Less than 3 Min.

Remaining Charge*

— — CLOSED OPEN — —

Battery More than 2

Min. Remaining Charge*

— — — — OPEN CLOSED

Battery Less than 2 Min.

Remaining Charge*

— — — — CLOSED OPEN

Contact Action Open on

Line

Failure

Close on

Line

Failure

Battery

Below

Mid

Battery

Open

Below

Mid

Battery

Below

Low

Battery

Open

Below

Mid

Battery

* Times are approximate, at full load.

LINE FAIL

K1 A

LO BATT

K1 0A

OPENS ON LI NE FA IL

CLOSES ON LINE FA IL

CLOSES BE LOW LOW BATTER Y

TOP OF DUAL

DB9 (J5/J34)

NO TE :

CLOSES BELOW MID BATTERY

REMOTE CONTAC TS

COM

MID BAT

K4 A

COM

OPENS

BELOW MID BATT ERY

RELA YS SHOW N DE-ENE RGIZ ED

OPENS BELOW LOW BATTERY

Use the included USB cable (see

) and/or DB9

serial cable (see

) to connect the communication

port on your computer to the communication port of

your UPS. Install on your computer the Tripp Lite

PowerAlert

software appropriate to your computer’s

operating system. Consult your PowerAlert manual for

more information.

15-12-015- 932460.indb 7 1/19/2016 4:10:10 PM

Optional Installation

EPO Port Connection

This optional feature is only for those applications

which require connection to a facility’s Emergency

Power Off (EPO) circuit. When the UPS is connected

to this circuit, it enables emergency shutdown of the

UPS’s inverter.

Using the cable provided, connect the EPO port of

your UPS (see

) to a user-supplied normally closed

or normally open switch according to the circuit

diagram (see

). The EPO port is not a phone line

surge suppressor; do not connect a phone line to this

port.

4-5

connection base step 1

External Battery Connection

All UPS models come with a robust internal battery

system; select models feature connectors (see

)

that accept optional external battery packs (sold

separately from Tripp Lite) to provide additional

runtime. Adding external batteries will increase

recharge time as well as runtime. See battery pack

owner’s manual for complete installation instructions.

Make sure cables are fully inserted into their

connectors. Small sparks may result during battery

connection; this is normal. Do not connect or

disconnect battery packs when the UPS is running on

battery power.

If you connect any external batteries, set the Battery

Charge Level Switch (see

) to the down position.

This will increase your UPS’s charger output so the

additional batteries charge faster.

Note: the switch to the right of the Battery Charge Level

Switch is inactive and will not affect UPS operation regardless

of its position.

CAUTION! DO NOT set the Battery Charge Level

Switch to the down position without an external

battery connected. There is a risk of damaging

the UPS’s internal battery system.

15-12-015- 932460.indb 8 1/19/2016 4:10:11 PM

Basic Operation

Buttons (Front Panel)

“ON/OFF/STANDBY” Button

When the UPS system is connected to a live AC utility power source, the UPS

System will operate in one of three modes: ON, OFF or STANDBY. Refer to the chart

below for UPS System operating characteristics within each mode.

Mode

UPS Charges Battery

(when utility is present)

UPS Supplies Power to

Outlets (when utility is

present or absent*) UPS Displays LEDs

ON Yes Yes Yes (variety of LEDs,

depending on conditions)

OFF No No No

STANDBY Yes No Yes (“BATTERY CHARGE”

LED only)

To place the UPS in the ON mode: First, have a qualified electrician connect the

UPS System to a utility power source as outlined in the Quick Installation section.

Once the utility power source is live, the UPS System will automatically enter

STANDBY mode. Press and hold the “ON/OFF/STANDBY” button for one second**

and then release it to switch the UPS System from STANDBY mode to ON mode.

OPTIONAL: If the utility power source is not live, you can “cold-start” the UPS

System (i.e.: switch it directly from the OFF mode to the ON mode by supplying

power for a limited time from its batteries*) by pressing and holding the “ON/

OFF/STANDBY” button for one second** and then releasing it.

To place the UPS in the OFF mode: With the UPS System in the ON mode and

receiving utility power, press and hold the “ON/OFF/STANDBY” button for one

second** and then release it to switch the UPS System from ON mode to

STANDBY mode. Switch OFF the facility’s circuit breaker which is supplying power

to the circuit the UPS System is connected to.

* If batteries are fully charged. ** The alarm will beep once briefly after the interval has passed.

“MUTE/TEST” Button

To Silence (or “Mute”) UPS Alarms: briefly press and release the MUTE/TEST

button.*

To Run a Self-Test: with your UPS connected to a live utility power source and

turned ON, press and hold the MUTE/TEST button for two seconds.* Continue

holding the button until the alarm beeps several times and the UPS performs a self

test. See “Results of a Self-Test” below.

Note: you can leave connected equipment on during a self-test. Your UPS, however, will not

perform a self-test if the UPS is not turned on (see “ON/OFF/STANDBY” Button description).

Results of a Self-Test: the test will last approximately 10 seconds as the UPS

switches to battery to test its load capacity and battery charge.

• If the “OUTPUT LOAD LEVEL” LED remains lit red and the alarm continues to

sound after the test, the UPS’s outlets are overloaded. To clear the overload,

unplug some of your equipment and run the self-test repeatedly until the

“OUTPUT LOAD LEVEL” LED is no longer lit red and the alarm is no longer

sounding.

CAUTION! Any overload that is not corrected by the user immediately

following a self-test may cause the UPS to shut down and cease supplying

output power in the event of a blackout or brownout.

15-12-015- 932460.indb 9 1/19/2016 4:10:11 PM

Basic Operation

• If the “BATTERY WARNING” LED remains lit and the alarm continues to sound

after the test, the UPS batteries need to be recharged or replaced. Allow the UPS

to recharge continuously for 12 hours, and repeat the self-test. If the LED

remains lit, contact Tripp Lite for service. If your UPS requires battery

replacement, visit http://www.tripplite.com/products/battery-finder/ to locate the

specific Tripp Lite replacement battery for your UPS.

* The alarm will beep once briefly after the indicated interval has passed.

Indicator Lights (Front Panel)

All Indicator Light descriptions apply when the UPS is connected to a live utility power source and

turned ON.

“POWER” LED: this green LED lights continuously when the UPS is ON and

supplying connected equipment with AC power from a utility source. The LED

flashes and an alarm sounds (4 short beeps followed by a pause) to indicate the

UPS is operating from its internal batteries during a blackout or severe brownout. If

the blackout or severe brownout is prolonged, you should save files and shut down

your equipment since internal battery power will eventually be depleted. See

“BATTERY CHARGE” LED description below.

“VOLTAGE CORRECTION” LED: this green LED lights continuously whenever the

UPS is automatically correcting high or low AC voltage on the utility line without the

assistance of battery power. The UPS will also emit a slight clicking noise. These

are normal, automatic operations of the UPS, no action is required on your part.

“OUTPUT LOAD LEVEL” LED: this multicolored LED indicates the approximate

electrical load of equipment connected to the UPS’s AC outlets. It will turn from

green (light load) to yellow (medium load) to red (overload). If the LED is red (either

illuminated continuously or flashing), clear the overload immediately by unplugging

some of your equipment from the outlets until the LED changes from red to yellow

(or green).

CAUTION! Any overload that is not corrected by the user immediately may

cause the UPS to shut down and cease supplying output power in the event

of a blackout or brownout.

“BATTERY CHARGE” LED: when the UPS is operating from utility power, this LED

indicates the approximate charge state of the UPS’s internal batteries: red indicates

the batteries are beginning to charge; yellow indicates the batteries are roughly

midway through charging; and green indicates the batteries are fully charged. When

the UPS is operating from battery power during a blackout or severe brownout, this

LED indicates the approximate amount of energy (ultimately affecting runtime)

which the UPS’s batteries will provide: red indicates a low level of energy; yellow

indicates a medium level of energy; and green indicates a high level of energy.

Since the runtime performance of all UPS batteries will gradually deplete over time,

it is recommended that you periodically perform a self-test (see MUTE/TEST Button

description) to determine the energy level of your UPS batteries BEFORE a blackout

or severe brownout occurs. During a prolonged blackout or severe brownout, you

should save files and shut down your equipment since battery power will eventually

be depleted. When the LED turns red and an alarm sounds continuously, it

indicates the UPS’s batteries are nearly out of power and UPS shut down is

imminent.

15-12-015- 932460.indb 10 1/19/2016 4:10:12 PM

Basic Operation

“BATTERY WARNING” LED: this LED lights red and an alarm sounds intermittently

after you complete a self test (See “MUTE/TEST” Button description) to indicate the

UPS batteries need to be recharged or replaced. Allow the UPS to recharge

continuously for 12 hours, and repeat the self-test. If the LED continues to light,

contact Tripp Lite for service. If your UPS requires battery replacement, visit

http://www.tripplite.com/products/battery-finder/ to locate the specific Tripp Lite

replacement battery for your UPS.

C13/230V

C19/230V

Charge Rate

Setting (when

External

Batteries are

not connected)

Charge Rate

Setting (when

External

Batteries are

connected)

Other UPS Features (Rear Panel)

AC Receptacles: Your UPS features C13 outlets, and select models also feature

C19 outlets. These output receptacles provide your connected equipment with AC

line power during normal operation and battery power during blackouts and

brownouts. The UPS protects equipment connected to these receptacles against

damaging surges and line noise. If you have a serial or USB connection to your

UPS, you can remotely reboot connected equipment by turning the receptacles

OFF and ON using Tripp Lite’s PowerAlert software.

Input Terminal block: Use these terminals to connect the UPS System to

utility power. Unscrew and remove the cover over the block for access.

Communications Ports (USB or RS-232): These ports connect your UPS to any

workstation or server. Use with Tripp Lite’s PowerAlert software and included cables

to enable your computer to automatically save open files and shut down equipment

during a blackout. Also use PowerAlert software to monitor a wide variety of AC line

power and UPS operating conditions. Consult your PowerAlert software manual or

contact Tripp Lite Customer Support for more information. See “USB and RS-232

Serial Communications” in the “Optional Installation” section for installation

instructions.

Relay Contact Interface Port: This female DB9 port sends contact-closure

signals to indicate line-fail and low battery status. See “Optional Installation”

section for installation instructions.

EPO (Emergency Power Off) Port: Your UPS features a EPO port that may be

used to connect the UPS to a contact closure switch to enable emergency inverter

shutdown. See “EPO Port Connection” in the “Optional Installation” section for

more information.

Battery Charge Level Switch: Controls the UPS system’s battery charge rate. If

you connect any external batteries, set the Battery Charge Level Switch to the

down position. This will increase your UPS’s charger output so the additional

batteries charge faster. Note: the switch to the right of the Battery Charge Level

Switch is inactive and will not affect UPS operation regardless of its position.

CAUTION! DO NOT set the Battery Charge Level Switch to the down position

without an external battery connected. There is a risk of damaging the

UPS’s internal battery system.

15-12-015- 932460.indb 11 1/19/2016 4:10:13 PM

Basic Operation

Accessory Slot: Remove the small cover panel from this slot to install optional

accessories to remotely monitor and control your UPS. Refer to your accessory’s

manual for installation instructions. Visit tripplite.com for more information,

including a list of available SNMP, network management and connectivity products.

Power Sensitivity Adjustment: This dial is normally set fully counter-clockwise,

which enables the UPS to provide maximum protection against waveform

distortions in its AC input. When such distortion occurs, the UPS will normally

switch to providing sine wave power from its battery reserves for as long as the

distortion is present. In areas with poor utility power or where the UPS’s input

power comes from a backup generator, chronic waveform distortion could cause

the UPS to switch to battery too frequently, draining its battery reserves. You may

be able to reduce how often your UPS switches to battery due to moderate

waveform distortion by experimenting with different settings for this dial. As the dial

is turned clockwise, the UPS becomes more tolerant of variations in its input

power’s AC waveform.

Note: The further the dial is adjusted clockwise, the greater the degree of waveform distortion

the UPS will allow to pass to connected equipment.

When experimenting with different settings for this dial, operate connected

equipment in a safe test mode so that the effect on the equipment of any

waveform distortions in the UPS’s output can be evaluated without disrupting

critical operations.

External Battery Connector: Use to connect Tripp Lite external battery packs for

additional runtime. Refer to instructions available with the battery pack for

complete connection information and safety warnings.

Output Breaker(s): Protect your UPS from output overload. If one or more

breakers trip, remove some of the load on the circuit(s), then reset them by

pressing the breaker switch(es) in.

Ground Screw: Use this to connect any equipment that requires a chassis ground.

15-12-015- 932460.indb 12 1/19/2016 4:10:14 PM

Storage and Service

Storage

Before storing your UPS, turn it completely OFF. If you store your UPS for an extended period of

time, recharge the UPS batteries for 4 to 6 hours once every three months. Note: after you

connect the UPS to utility power, it will automatically begin charging its batteries. If you leave

your UPS batteries discharged for an extended period of time, they will suffer a permanent loss of

capacity.

Service

Before returning your UPS for service, follow these steps:

1. Review the installation and operation procedures in this manual to insure that the service

problem does not originate from a misreading of the instructions. Also, check that the UPS

System’s circuit breaker(s) are not tripped. This is the most common cause of service inquiries

which can be easily remedied by following the resetting instructions in this manual.

2. If the problem continues, do not contact or return the product to the dealer. Instead, visit

www.tripplite.com/support.

3. If the problem requires service, visit www.tripplite.com/support and click the “Request Return

(RMA)” link. From here you can request a Returned Material Authorization (RMA) number,

which is required for service. This simple on-line form will ask for your unit’s model and serial

numbers, along with other general purchaser information. The RMA number, along with

shipping instructions will be emailed to you. Any damages (direct, indirect, special or

consequential) to the product incurred during shipment to Tripp Lite or an authorized Tripp Lite

service center are not covered under warranty. Products shipped to Tripp Lite or an authorized

Tripp Lite service center must have transportation charges prepaid. Mark the RMA number on

the outside of the package. If the product is within its warranty period, enclose a copy of your

sales receipt. Return the product for service using an insured carrier to the address given to

you when you request the RMA.

15-12-015- 932460.indb 13 1/19/2016 4:10:14 PM

Battery Replacement

WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union)

Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing

regulations, when customers buy new electrical and electronic equipment from Tripp Lite they are

entitled to:

• Send old equipment for recycling on a one-for-one, like-for-like basis (this varies depending on

the country)

• Send the new equipment back for recycling when this ultimately becomes waste

Battery replacement should be performed only by authorized service personnel using the same

number and type of batteries (sealed Lead-Acid). Under normal conditions, the original batteries

in your UPS will last many years. See Safety section before replacing batteries. The batteries are

designed for hot-swap replacement (i.e. leaving the UPS in ON mode), but some qualified service

personnel may wish to put the UPS in the OFF mode and disconnect equipment before

proceeding.

Procedure

Remove Front Panel and Battery Holding Plate

Disconnect Batteries

Remove/Dispose of Batteries

Add Batteries

Connect Batteries

Attach connectors: black-to-black and red-to-red.

Replace Front Panel

WARNING!

Batteries can present a risk of electrical shock

and burn from high short-circuit current result-

ing in serious injury or death. Battery terminals

are in close proximity to UPS cabinet and spe-

cial care must be taken to avoid shorting the

batteries including not touching metal

cabinet and battery terminals simultaneously.



2 5

1 6

3 4

UPS and Battery Recycling

Please recycle Tripp Lite Products. The batteries used in Tripp Lite products are sealed Lead-

Acid batteries. These batteries are highly recyclable. Please refer to your local codes for disposal

requirements.

You can call Tripp Lite for recycling info at 1-773-869-1234.

You can go to the Tripp Lite Website for up-to-date information on recycling the batteries or any

Tripp Lite product. Please follow this link: http://www.tripplite.com/support/recycling-program/

15-12-015- 932460.indb 14 1/19/2016 4:10:15 PM

Regulatory Compliance Identiﬁcation Numbers

For the purpose of regulatory compliance certiﬁcations and identiﬁcation, your Tripp Lite product has been

assigned a unique series number. The series number can be found on the product nameplate label, along

with all required approval markings and information. When requesting compliance information for this product,

always refer to the series number. The series number should not be confused with the marketing name or model

number of the product.

Tripp Lite has a policy of continuous improvement. Speciﬁcations are subject to change without notice.

Note on Labeling

Two symbols are used on the label.

V~ : AC Voltage

V : DC Voltage

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

15-12-015- 932460.indb 15 1/19/2016 4:10:15 PM

Manual del propietario

UPS SmartPro

para Instalación de

3U en Rack

Modelo: SMX5000XLRT3U

(Número de Serie: AGSM5247)

No conveniente para los usos móviles.

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

SmartPro

es una marca comercial registrada de Tripp Lite.

Instrucciones de .............17

seguridad importantes

Montaje ..........................18

Instalación rápida ...........20

Instalación opcional ........22

Operación básica ............24

Almacenamiento ............28

y servicio

Reemplazo de batería .....29

English ..............................1

Français ..........................31





15-12-015- 932460.indb 16 1/19/2016 4:10:16 PM

Instrucciones de seguridad importantes

GUARDE ESTAS INSTRUCCIONES

Este manual contiene importantes instrucciones que deben seguirse durante la

instalación, operación y el almacenamiento de todos los UPS de Tripp Lite. La falta de

observar estas advertencias podría afectar su garantía.

Advertencias sobre la ubicación del UPS

• Tenga cuidado al levantar el UPS. Debido al gran peso de los UPS para montaje en bastidor, se

requieren por lo menos dos personas para que le ayuden a levantarlos e instalarlos.

• Instale su UPS bajo techo, lejos de la humedad, el calor, el polvo o la luz solar directa.

• Para un mejor funcionamiento, la temperatura ambiente cerca de su UPS debe estar entre 0°

C y 40° C (32° F - 104° F)

• Deje una cantidad adecuada de espacio alrededor de todos los lados del UPS para sua

adecuada ventilación. No obstruya sus respiraderos ni las aberturas de ventilación.

• No monte esta unidad con el panel frontal o con el panel trasero hacia abajo (Bajo ningún

ángulo o inclinación). Si lo monta de esta manera, inhibirá seriamente el sistema de

enfriamiento interno de la unidad; lo que finalmente causará daños al producto que no están

cubiertos por la garantía.

Advertencias sobre la conexión del UPS

• El UPS contiene su propia fuente de energía (batería). Los terminales de salida pueden estar

con energía incluso cuando el UPS no está conectado a un suministro de corriente alterna.

Advertencias sobre la conexión de equipos

• El uso de este equipo en aplicaciones de soporte de vida en donde la falla de este equipo

pueda razonablemente hacer suponer que causará fallas en el equipo de soporte de vida o

afecte significativamente su seguridad o efectividad, no está recomendado. No use este equipo

en la presencia de una mezcla anestésica inflamable con aire, oxigeno u óxido nitroso.

• No conecte supresores de sobretensiones ni cordones de extensión a la salida de su UPS. Esto

puede sobrecargarlo y anular su garantía y la del supresor de sobretensiones.

Advertencias sobre la batería

• Debido a que las baterías presentan un peligro de choque eléctrico y quemaduras por

las altas corrientes de cortocircuito, tome las precauciones adecuadas. No deseche las

baterías en un incinerador. No abra las baterías. No ponga los terminales de la batería en

corto o en puente con ningún objeto. Apague y desconecte el UPS antes de reemplazar la

batería. Sólo debe cambiar las baterías personal técnico debidamente capacitado. Use

herramientas con mangos aislados y reemplace las baterías existentes con el mismo número y

tipo de baterías nuevas (plomo-ácido selladas). Las baterías del UPS son reciclables. Consulte

la reglamentación local para los requisitos de disposición de desechos o visita

http://www.tripplite.com/support/recycling-program para reciclar información. Tripp Lite ofrece

una línea completa de Cartuchos de reemplazo de batería para UPS (R.B.C.). Visite Tripp Lite

en la web en http://www.tripplite.com/products/battery-finder/ para localizar la batería de

reemplazo específica para su UPS.

• Durante el reemplazo de baterías en operación (hot-swap), el UPS no proporcionará energía de

respaldo en el caso de una falla del servicio eléctrico u otras interrupciones de energía.

• No opere el UPS sin baterías.

• Al agregar bancos de baterías externas, sólo emplee bancos recomendados por Tripp Lite del

voltaje y tipo correctos. No conecte ni desconecte bancos de baterías cuando el UPS esté

funcionando con energía de las baterías.

15-12-015- 932460.indb 17 1/19/2016 4:10:16 PM

Montaje

Su UPS puede instalarse en rack de 4 o 2 postes. Para instalar el UPS (módulo de potencia +

módulo de baterías externas) en un rack de 2 postes, compre los accesorios apropiados, se

venden por separado (ordene # modelo 2POSTRMKITHD de Tripp Lite). Para instrucciones de

instalación, vea el manual del propietario del 2POSTRMKITHD. Para instalar el UPS en un rack de

4 postes, use los accesorios incluidos y siga el procedimiento detallado a continuación. Los

procedimientos son para tipos comunes de racks y pueden no ser apropiados para todas las

configuraciones de rack. Antes de la instalación, el usuario debe determinar la adecuación de los

accesorios y procedimientos.

PRECAUCIÓN: El equipo para instalación en rack puede ser extremadamente pesado—

tenga cuidado al mover o levantar el equipo. De ser necesario, use uno o más ayudantes.

Instalación en Rack de 4 Postes

Instalación en Rack con Orificios Cuadrados

Las espigas de plástico

incluidas

soportarán temporalmente los

entrepaños

para instalación en rack,

vacíos, mientras usted instala los

accesorios de instalación permanentes.

Inserte una espiga cerca del centro del

soporte frontal y posterior de cada

entrepaño, como se muestra. (Cada

soporte frontal tiene 6 orificios y cada

soporte trasero tiene 3 orificios). Las

espigas abrocharán es su lugar.

Después de instalar las espigas, expanda cada entrepaño para hacer coincidir la profundidad

de los rieles de su rack. Las espigas ajustarán a través de los orificios cuadrados en los rieles

del rack para soportar los entrepaños. Consulte las etiquetas en la unidad de rack para

confirmar que los entrepaños estén nivelados en todas direcciones.

Nota: El borde de apoyo de cada entrepaño debe apuntar hacia adentro.

Asegure permanentemente los

entrepaños

a los rieles de

instalación usando los tornillos y las

arandelas de copa

como se

muestra. Coloque 6 tornillos en total

en el frente y 4 tornillos en total en la

parte posterior.

Apriete todos los tornillos antes de

continuar.

Advertencia: No intente instalar su equipo hasta que haya insertado y apretado los

tornillos requeridos. Las espigas de plástico no soportarán el peso de su equipo.

Coloque los soportes de instalación de

su equipo a los orificios de instalación

del frente del gabinete usando los

accesorios incluidos con su equipo.

Las “orejas” del soporte de instalación

deben apuntar al frente. (Algún equipo

puede tener preinstalados o integrados

los soportes de instalación).

15-12-015- 932460.indb 18 1/19/2016 4:10:17 PM

Con la ayuda de un asistente (si fuera

necesario), levante su equipo y

deslícelo en los entrepaños. Coloque

los soportes de instalación del equipo

en los rieles de instalación delanteros

con los tornillos y arandelas

suministrados por el usuario

. Apriete

con firmeza todos los tornillos.

Montaje

Instalación en Rack con Orificios Roscados

Alinee el riel de instalación

a lo

largo de la superficie interior de los

postes del rack

de modo que las

bridas en los extremos del riel

envuelvan las superficies frontal y

posterior de los postes y los orificios

del riel coincidan con los orificios

roscados en el poste del rack.

Asegure permanentemente los

entrepaños

los rieles de instalación

usando tornillos y arandelas,

suministradas por el usuario,

para

su rack como se muestra. Coloque 6

tornillos en total en el frente y 4

tornillos en total en la parte posterior.

Apriete todos los tornillos antes de

continuar.

Advertencia: No intente instalar su equipo hasta que haya insertado y apretado los

tornillos y tuercas requeridos.

Siga los pasos

de las instrucciones de Instalación en Rack con Orificios Cuadrados

(arriba) para instalar firmemente su equipo de 3U.

Montaje de torre

Si monta en torre este UPS, debe agregar un pedestal de

torre Tripp Lite de 2U a 9U (modelo: 2-9USTAND, vendido

por separado). Consulte el procedimiento de instalación

en el manual del propietario.

Gire el panel de control del módulo de potencia para

obtener mejor visibilidad mientras el UPS esté montado

en torre. Introduzca un pequeño destornillador u otra

herramienta en las ranuras en cualquier lado del panel de

control. Saque el panel, gírelo y colóquelo en posición

nuevamente.

15-12-015- 932460.indb 19 1/19/2016 4:10:20 PM

Instalación rápida

¡PELIGRO!

¡ALTO VOLTAJE! ¡RIESGO DE LESIONES GRAVES

O MUERTE! ¡SÓLO PARA ELECTRICISTAS

EXPERIMENTADOS! LOS ELECTRICISTAS DEBEN

LEER LAS ADVERTENCIAS DE LA SECCIÓN

SEGURIDAD ANTES DE LA INSTALACIÓN.

connection base step 1

Conecte los terminales de

entrada del UPS a una fuente

de energía de la red.

Capacidades de entrada y salida

Modelo

Voltaje de

entrada

Capacidad máxima

de corriente de

entrada

Capacidad máxima

de corriente de

salida

Calibre de

alambre usual

SMX5000XLRT3U 230V 27A 30A 10 AWG

Antes de cablear, APAGUE el interruptor automático que suministra energía al circuito al que

estará conectado el UPS. Con un destornillador, retire la parte superior de la caja

que cubre

los terminales de entrada del UPS. Pase el cable suministrado por el usuario a través de la

abertura en la caja

y conéctelo a los terminales. Después de completar el cableado,

ENCIENDA el interruptor automático que suministra energía al circuito al que está conectado el

UPS. Tenga en cuenta que después de conectar el UPS en una fuente activa de energía de la red

pública, el UPS (en modo de espera) cargará automáticamente sus baterías, pero no suministrará

energía a sus tomacorrientes hasta que se ENCIENDA (ver paso 3 a continuación).

* El LED BATTERY CHARGE (CARGA DE BATERÍA) será el único iluminado.

Nota: El sistema UPS funcionará adecuadamente desde la puesta en marcha inicial, no obstante, la

autonomía máxima de la batería de la unidad solo se alcanzará después de que se haya cargado durante 24

horas.

¡ADVERTENCIAS DE CABLEADO!

• El cableado debe ser realizado por un electricista calificado.

• Al conectar conductores, observe en todo momento los reglamentos de conexión de

cables adecuados para su área. Asegúrese de instalar un interruptor de desconexión

fácilmente accesible en su cableado de modo que pueda cortar la entrada de corriente

alterna al UPS durante incendios y otras emergencias. Asegúrese que los cables cuenten

con mangas y estén asegurados con abrazaderas de conectores. Apriete las conexiones

con un torque no menor que 10 libras-pulgada (1.1 Nm)

• Asegúrese que su equipo esté puesto a tierra adecuadamente.

• El uso de cables de calibre inadecuado puede dañar su equipo y causar riesgos de

incendio. Elija cables y circuitos de protección adecuados para realizar las conexiones de

cableado (Los conductores de tierra deben ser del mismo tipo y calibre que los

conductores de energía utilizados).

15-12-015- 932460.indb 20 1/19/2016 4:10:21 PM

La page charge ...

Tripp Lite SmartPro 3U Rackmount UPS Le manuel du propriétaire

Marque: Tripp Lite

Modèle: SmartPro 3U Rackmount UPS

Catégorie: Alimentations sans interruption (UPS)

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Tripp Lite SmartPro 3U Rackmount UPS Owner's manual
español: Tripp Lite SmartPro 3U Rackmount UPS El manual del propietario

Tripp Lite SmartPro 3U Rackmount UPS Le manuel du propriétaire

Tripp Lite SmartPro 3U Rackmount UPS Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents