Sony HT-S100F Manuel utilisateur

HT-S100F

4-727-410-61(1)

HT-S100F

4-727-410-61(1)

K:\081\Win7 CS\new3\4727410611_HT-S100F_GB-FR-PR-

AR\00COV\010COV.fm

masterpage:

Right

HT-S100F

4-727-410-61(1)

HT-S100F

Operating Instructions

GB

Manuel d’instructions

FR

4-727-410-61(1)

Sound Bar

H:\0186-PC115\ML\4727410611_HT-S100F_GB-FR-PR-

AR\00COV\010BCO.fm

masterpage:

Right

HT-S100F

4-727-410-61(1)

HT-S100F

PR

AR

http://www.sony.net/

Sound Bar

2

GB

Do not install the appliance in a

confined space, such as a bookcase or

built-in cabinet.

To reduce the risk of fire, do not cover

the ventilation opening of the appliance

with newspapers, tablecloths, curtains,

etc.

Do not expose the appliance to naked

flame sources (for example, lighted

candles).

To reduce the risk of fire or electric

shock, do not expose this appliance to

dripping or splashing, and do not place

objects filled with liquids, such as vases,

on the appliance.

The unit is not disconnected from the

mains as long as it is connected to the

AC outlet, even if the unit itself has been

turned off.

As the main plug is used to disconnect

the unit from the mains, connect the

unit to an easily accessible AC outlet.

Should you notice an abnormality in the

unit, disconnect the main plug from the

AC outlet immediately.

Do not expose batteries or appliances

with battery-installed to excessive heat,

such as sunshine and fire.

Indoor use only.

Recommended cables

Properly shielded and grounded cables

and connectors must be used for

connection to host computers and/or

peripherals.

For the Bar Speaker

The nameplate is located on the bottom

of the Bar Speaker.

WARNING

3

GB

Table of Contents

About These Operating

Instructions ..............................3

What’s in the Box ..........................4

What You Can Do with the

System .....................................5

Guide to Parts and Controls ..........6

Preparing for Using the

System

Mounting the Bar Speaker on a

Wall .........................................12

When the TV Remote Control does

not Work ................................ 14

Listening to the Sound

Listening to a TV and Other

Devices .................................. 15

Listening to Music on a USB

Device .................................... 16

Selecting the Sound Effect

Adjusting the Sound .................... 18

Listening to Music/Sound

with the BLUETOOTH®

Function

Listening to Music from a Mobile

Device ....................................20

Turning the System On by

Operating the BLUETOOTH

Device .................................... 22

Turning the BLUETOOTH Function

Off .......................................... 22

Using the Various Functions

Using the Control for HDMI

Function .................................23

Saving Power Consumption ........24

Troubleshooting

Troubleshooting ..........................25

Resetting the System ..................29

Additional Information

Specifications ...............................30

Playable Types of Files

(USB Input) ............................. 31

Supported Input Audio Formats

(HDMI OUT (TV (ARC)) or TV IN

(OPTICAL)) .............................. 31

On BLUETOOTH

Communication .....................32

Precautions ..................................33

About These Operating

Instructions

•The instructions in these Operating

Instructions describe the controls on

the remote control.

•Some illustrations are presented as

conceptual drawings, and may be

different from the actual products.

•The default settings are underlined on

each feature description.

Basic Setup



Startup Guide

(separate

document)

GB

4

GB

What’s in the Box

•Bar Speaker (1)

• Remote control (1)

• R03 (size AAA) battery (2)

• Optical digital cable (1)

• AC power cord (mains lead) (1)

• WALL MOUNT TEMPLATE (1)

•Startup Guide

• Operating Instructions

5

GB

What You Can Do with the System

“Listening to a TV and Other Devices”

(page 15)

Blu-ray Disc™ player, cable

box, satellite box, etc.

Connecting the TV

(refer to “Startup Guide” (separate

document))

“Using the Control for HDMI Function”

(page 23)

“Listening to Music

on a USB Device”

(page 16)

“Listening to Music from a

Mobile Device” (page 20)

6

GB

Guide to Parts and Controls

Details are omitted from the illustrations.

Front

 Remote control sensor

Point the remote control at the

remote control sensor to operate

the system.

 (power) button

Turns on the system or sets it to

standby mode.

 (input select) button

(page 15)

 BLUETOOTH button (page 20)

 +/– (volume) buttons

 Indicators

For details, see “About the

indicators on the Bar Speaker”

(page 7).

Bar Speaker

7

GB

About the indicators on the Bar Speaker

Lighting and flashing of the indicator(s) on the Bar Speaker indicate the input or

status of the input device.

The indicators flash when turning on/off the function setting or operating the remote

control.

Indicators Status

• Lights: TV input is selected.

• Lights in blue: BLUETOOTH connection is established (BLUETOOTH input is

selected).

• Flashes quickly in blue: While waiting for connection with a device.

• Flashes in blue: While reconnecting or performing pairing.

• Lights: USB input is selected.

• Flashes twice: The play mode is changed.

• Flashes three times first, then flashes slowly repeatedly: When connecting an

unsupported device.

• Flashes repeatedly: While reading data of the connected USB device.

Indicators Status

• Flashes twice: One of the following functions is set to on.

–Night mode (page18)

–Voice mode (page18)

• Flashes once: The audio channel is set to Main (page 19), the sound mode is

selected (page 18), or one of the following functions is set to off.

–Night mode (page18)

–Voice mode (page18)

• Flashes twice: One of the following functions is set to on.

–Dolby DRC (page19)

– Control for HDMI (page 23)

– BLUETOOTH standby (page 22)

– BLUETOOTH function (page 22)

– Auto standby (page 24)

– IR repeater (page 14)

• Flashes once: The audio channel is set to Sub (page 19) or one of the following

functions is set to off.

–Dolby DRC (page19)

– Control for HDMI (page 23)

– BLUETOOTH standby (page 22)

– BLUETOOTH function (page 22)

– Auto standby (page 24)

– IR repeater (page 14)

• Flash once: The audio channel is set to Main/Sub (page 19).

• Flash quickly: The protection feature is activated (page 28).

• Flash slowly: The system enters standby mode by the auto standby

function (page 24).

8

GB

The indicators flash while adjusting the volume level.

Tip

You can turn the indicators off by pressing INDICATOR.

Even if the indicators are turned off by pressing INDICATOR, if you operate the system, the

indicators in relation to the operation light or flash.

Indicators Status

• Flashes once: The volume level is low.

• Flash once: The volume level is medium.

• Flash once: The volume level is high.

• Flash repeatedly: The sound is muted.

• Flash twice: The volume level is set to maximum/minimum.

9

GB

Rear

 AC IN terminal

 HDMI OUT (TV (ARC)) jack

Connect a TV that has an HDMI

input jack with an HDMI cable.

The system is compatible with

Audio Return Channel (ARC). ARC

is the function that sends TV

sound to an AV device such as the

system from the TV’s HDMI jack.

 (USB) port (page 16)

 TV IN (OPTICAL) jack

 IR repeater (page 14)

Transmits the remote signal of

the TV remote control to the TV.

10

GB

Some buttons function differently

depending on how long the button is

pressed. The icons below indicate how

long to press the button.

• : Press the button.

• : Press and hold the button for 5

seconds.

 INPUT (page 15)

Selects the playback source. When

you press INPUT once, the current

input indicator flashes.

Press INPUT again to select the

device you want.

Each time you press INPUT, the

input changes cyclically as follows.

TV input BLUETOOTH input 

USB input

 AUTO SOUND (page 18)

Selects AUTO SOUND for the sound

effect.

 CINEMA

: Selects CINEMA for the sound

effect. (page 18)

: Turns on/off the auto standby

function. (page 24)

 VOICE

: Turns on/off the voice mode.

(page 18)

: Turns on/off the Control for

HDMI function. (page 23)

  (volume) +*/–

Adjusts the volume.

 INDICATOR (page 7)

Turns on/off the indicators on the

Bar Speaker.

 PLAY MODE (page 16)

Selects the play mode for USB

playback.

 / (page 16)

Select the content on the TV screen

for USB playback.

Remote Control

11

GB

/ (previous/next)

(page 16, 20)

Pressing the button shortly goes to

the beginning of the previous or

next file.

Pressing and holding searches

backward or forward (rewind/fast

forward).

 (power)

Turns on the system or sets it to

standby mode.

 STANDARD

: Selects STANDARD for the

sound effect. (page 18)

: Turns on/off the IR repeater

function. (page 14)

 MUSIC (page 18)

Selects MUSIC for the sound effect.

 NIGHT

: Turns on/off the night mode.

(page 18)

: Turns on/off the BLUETOOTH

standby mode. (page 22)

  (muting)

Turns off the sound temporarily or

turn on the sound.

 AUDIO*

: Selects the audio channel for

Dolby Digital multiplex broadcast.

(page 19)

: Turns on/off the Dolby DRC

function. (page 19)

 ENTER (page 16)

Plays the content that is selected by

/ for USB playback.

  (play/pause)* (page 16, 20)

Pauses or resumes playback.

*The AUDIO,  +, and  buttons have

a tactile dot. Use it as a guide during

operation.

12

GB

Mounting the Bar

Speaker on a Wall

You can mount the Bar Speaker on a

wall.

• Prepare screws (not supplied) that are

suitable for the wall material and

strength. As a plasterboard wall is

especially fragile, attach the screws

securely in the wall beam. Install the

speakers horizontally, hung by screws in

studs in a continuous flat section of the

wall.

• Have the installation done by a Sony

dealer or licensed contractor and pay

special attention to safety during the

installation.

• Sony shall not be held responsible for

accidents or damage caused by improper

installation, insufficient wall strength,

improper screw installation or natural

disaster, etc.

1 Prepare two screws (not supplied)

that are suitable for the wall

mount holes on the rear of the Bar

Speaker.

2 Stick WALL MOUNT TEMPLATE

(supplied) on a wall.

1 Align TV CENTER LINE () of

WALL MOUNT TEMPLATE with the

center line of your TV.

2 Align TV BOTTOM LINE () of

WALL MOUNT TEMPLATE with the

bottom of your TV, then stick

WALL MOUNT TEMPLATE on a

wall by using a commercially

available adhesive tape, etc.

Preparing for Using the System

Notes

Hole on the rear of the Bar Speaker

4mm

More than 30 mm

5 mm

10 mm

Center of the TV

WALL MOUNT

TEMPLATE

Adhesive tape,

etc.

13

GB

3 Fasten the screws into the marks

on SCREW LINE () of WALL

MOUNT TEMPLATE as the

illustration below.

4 Remove WALL MOUNT TEMPLATE.

5 Hang the Bar Speaker on the

screws.

Align the holes of the rear of the Bar

Speaker with the screws, then hang

the Bar Speaker on the two screws.

When sticking WALL MOUNT TEMPLATE,

smooth it out fully.

Screws

Marks

6 mm to

7mm

228.5 mm

Note

14

GB

When the TV Remote

Control does not Work

When the Bar Speaker obstructs the

remote control sensor of the TV, the TV

remote control may not work. In that

case, enable the IR repeater function of

the system.

You can control the TV with the TV

remote control by sending the remote

signal from the rear of the Bar Speaker.

Press and hold STANDARD for 5

seconds to set the function to on or

off.

• Be sure to check that the TV remote

control cannot control the TV, and then

set the IR repeater function to on. If it is

set to on when the remote control can

control the TV, appropriate operation

may not be obtained because of the

interference between the direct

command from the remote control and

the command via the Bar Speaker.

• On some TVs, this function may not work

correctly. In this case, place the Bar

Speaker slightly further away from the TV.

IR repeater on

The USB indicator flashes twice.

IR repeater off

The USB indicator flashes once.

Notes

15

GB

Listening to a TV and

Other Devices

1 Press INPUT repeatedly.

When you press INPUT once, the

current input indicator flashes.

Press INPUT again to select the

device you want.

The indicator of the selected device

lights up.

Each time you press INPUT, the

input changes cyclically as follows.

TV input  BLUETOOTH input 

USB input

2 Adjust the volume by pressing 

+/– on the remote control.

Tip

You can also select the input by pressing

on the Bar Speaker.

Listening to the Sound

INPUT

 +/–

TV input

• TV that is connected to the TV IN

(OPTICAL) jack

• TV compatible with the Audio Return

Channel (ARC) function that is

connected to the HDMI OUT (TV (ARC))

jack

When you connect the TV to both the

HDMI OUT (TV (ARC)) and TV IN

(OPTICAL) jacks, the input of the HDMI

OUT (TV (ARC)) jack has priority.

BLUETOOTH input

BLUETOOTH device that supports A2DP

For details, see “Listening to Music/

Sound with the BLUETOOTH® Function”

(page 20).

USB input

USB device that is connected to the

(USB) port

For details, see “Listening to Music on a

USB Device” (page 16).

16

GB

Listening to Music on a

USB Device

You can play music files stored on a

connected USB device.

For playable types of files, see “Playable

Types of Files (USB Input)” (page 31).

• To view the USB content list on the TV

screen, make sure you connect the

system to the TV using an HDMI cable.

• Change the input of the TV to the input

which the Bar Speaker is connected.

1 Connect the USB device to the

(USB) port.

2 Press INPUT repeatedly to select

the USB input.

The USB indicator lights up and the

USB content list appears on the TV

screen.

3 Press / to select the content

you want, then press ENTER.

The selected content starts playing.

4 Press PLAY MODE repeatedly to

select the play mode you want.

• None: Plays back all tracks.

• [Repeat One]: Repeats one track.

• [Repeat Folder]: Repeats all tracks

in a folder.

• [Shuffle]: Repeats all tracks in a

folder in random order.

The USB indicator flashes twice

each time you press PLAY MODE.

5 Adjust the volume by pressing 

+/– on the remote control.

Notes

ENTER

PLAY MODE

 +/–



/

INPUT

/

17

GB

Other operations

• Do not remove the USB device during

operation. To avoid data corruption or

damage to the USB device, turn the

system off before connecting or

removing the USB device.

• The USB indicator flashes three times first,

then flashes slowly repeatedly if you

connect an unsupported USB device.

• Depending on the file format, rewind and

fast forward do not work.

 Playing time

 Total playing time

 Selected file index/Total files in the

folder

 Play mode

 Playback status

 Rewind/fast forward speed

The following messages appear on the

TV screen depending on the status of

the USB device.

•[No USB]

No USB device is inserted.

•[Waiting]

The system is searching a USB device.

•Depending on the playback source, some

information may not be displayed.

•Depending on the play mode, the

information displayed may be different.

To Do this

Pause or resume

playback

Press .

Select the previous or

next track

Press /.

Search backward or

forward (rewind/fast

forward)

Press and hold

/.

Notes

Information of USB Device

on the TV Screen

Notes

18

GB

Adjusting the Sound

You can easily enjoy pre-programmed

sound effects that are tailored to

different kinds of sound sources.

Press AUTO SOUND, CINEMA, MUSIC,

or STANDARD to select the sound

mode.

When selecting the sound mode, the TV

indicator flashes once.

You can compress sound in accordance

with the information contained in the

content by setting the night mode to on.

Sound is output at low volume with

minimum loss of fidelity and clarity of

dialogue.

Press NIGHT to set the function to on

or off.

When you turn the system off, the night

mode is set to off automatically.

You can make dialogs clearer by setting

the voice mode to on.

Press VOICE to set the function to on

or off.

Selecting the Sound Effect

Enjoying the Sound Effect

that is Tailored to Sound

Sources (Sound Mode)

AUTO SOUND

You can enjoy the sound with Sony-

recommended sound mode. The sound

mode is automatically optimized according

to playback content and function.

CINEMA

Sounds are played back with surround

effects, and they are realistic and powerful,

making them suitable for movies.

MUSIC

Sound effects are optimized for listening to

music.

STANDARD

AUTO SOUND

MUSIC

CINEMA

STANDARD

Sound effects are optimized for the

individual source.

Enjoying Clear Sound with

Low Volume at Midnight

(NIGHT)

Night mode on

The TV indicator flashes twice.

Night mode off

The TV indicator flashes once.

Note

Making Dialogs Clearer

(VOICE)

Voice mode on

The TV indicator flashes twice.

Voice mode off

The TV indicator flashes once.

19

GB

This function works only when playing

the Dolby Digital signal of the device

that is connected to the TV IN

(OPTICAL)/HDMI OUT (TV (ARC)) jack.

When you set Dolby DRC (Dynamic

Range Control) to on, dynamic range of

the audio signal (range between the

maximum and minimum volume) is

compressed and sound with low

volume is easy to hear.

Press and hold AUDIO for 5 seconds to

set the function to on or off.

You can enjoy multiplex broadcast

sound when the system receives a

Dolby Digital multiplex broadcast signal.

Press AUDIO repeatedly.

The channel changes cyclically as

follows.

Main

 Sub  Main/Sub

To receive a Dolby Digital signal, you need

to connect a TV or other devices to the TV

IN (OPTICAL) jack with the optical digital

cable (supplied) or the HDMI OUT (TV

(ARC)) jack with an HDMI cable (not

supplied).

Making Sound with Low

Volume Easy to Hear by

Compressing Dynamic

Range

Dolby DRC on

The USB indicator flashes twice.

Dolby DRC off

The USB indicator flashes once.

Enjoying Multiplex

Broadcast Sound (AUDIO)

Main

Outputs only the main channel.

The TV indicator flashes once.

Sub

Outputs only the sub channel.

The USB indicator flashes once.

Main/Sub

Main sound is output from the left speaker

and sub sound is output from the right

speaker.

The TV and USB indicators flash once.

Note

20

GB

Listening to Music from

a Mobile Device

You can listen to music stored on a

mobile device such as a smartphone or

tablet via a wireless connection by

connecting the system and the mobile

device with the BLUETOOTH function.

When connecting to the mobile device

with the BLUETOOTH function, you can

operate by simply using the supplied

remote control without turning the TV

on.

1 Press and hold the BLUETOOTH

button on the Bar Speaker for 5

seconds.

The system enters the pairing mode

and the BLUETOOTH indicator

flashes quickly.

2 On the mobile device, turn on the

BLUETOOTH function, and then

select “HT-S100F” after searching

for it.

If a Passkey is requested, enter

“0000.”

3 Make sure that the BLUETOOTH

indicator on the Bar Speaker lights

in blue.

A connection between the system

and mobile device has been

established.

4 Start audio playback with the

music app on the connected

mobile device.

Sound is output from the Bar

Speaker.

5 Adjust the volume.

• Adjust the volume by pressing 

+/– on the remote control.

•  and / on the remote

control can be used for the

BLUETOOTH function.

• You can pair up to 8 BLUETOOTH devices.

If a 9th BLUETOOTH device is paired, the

least recently connected device will be

replaced by the new one.

• Perform pairing for the second and

subsequent mobile devices.

Tips

• You can check the connection status of

the BLUETOOTH function by checking the

BLUETOOTH indicator status (page 7).

• While the BLUETOOTH input is being

selected, the system enters the pairing

mode by pressing the BLUETOOTH button

on the Bar Speaker shortly.

Listening to Music/Sound with the

BLUETOOTH® Function

Listening to Music by Pairing

with a Mobile Device

BLUETOOTH

indicator

BLUETOOTH

button

Notes

La page charge ...

Sony HT-S100F Manuel utilisateur

Ce manuel convient également à

Sony HT-S100F Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents