Sony CDP-LSA1 Manuel utilisateur

4-227-583-12(1)

CDP-LSA1

2000 Sony Corporation

Compact Disc

Player

Operating Instructions

Mode d’emploi

Bedienungsanleitung

Manual de instrucciones

FR

DE

GB

ES

S200

TM

2

GB

WARNING

To prevent fire or shock

hazard, do not expose the unit

to rain or moisture.

To avoid electrical shock, do

not open the cabinet. Refer

servicing to qualified

personnel only.

The laser component in this product

is capable of emitting radiation

exceeding the limit for Class 1.

This appliance is classified as a CLASS 1

LASER product.

The CLASS 1 LASER PRODUCT

MARKING is located on the rear

exterior.

The following caution label is located

inside the unit.

Don’t throw a

battery, dispose it as

the injurious wastes.

Precautions

On safety

• Caution — The use of optical

instruments with this product will

increase eye hazard.

• Should any solid object or liquid fall

into the cabinet, unplug the player and

have it checked by qualified personnel

before operating it any further.

On power sources

• The unit is not disconnected from the

AC power source (mains) as long as it

is connected to the wall outlet, even if

the unit itself has been turned off.

• If you are not going to use the player

for a long time, be sure to disconnect

the player from the wall outlet. To

disconnect the AC power cord (mains

lead), grasp the plug itself; never pull

the cord.

• AC power cord must be changed only

at the qualified service shop.

On placement

• Place the player in a location with

adequate ventilation to prevent heat

build-up in the player.

• Do not place the player on a soft

surface such as a rug that might block

the ventilation holes on the bottom.

• Do not place the player in a location

near heat sources, or in a place subject

to direct sunlight, excessive dust or

mechanical shock.

On operation

If the player is brought directly from a

cold to a warm location, or is placed in a

very damp room, moisture may

condense on the lenses inside the player.

Should this occur, the player may not

operate properly. In this case, remove

the disc and leave the player turned on

for about an hour until the moisture

evaporates.

On adjusting the volume

Do not turn up the volume while

listening to a portion with very low level

inputs or no audio signals. If you do, the

speakers may be damaged when a peak

level portion is played.

On cleaning

Clean the cabinet, panel and controls

with a soft cloth slightly moistened with

a mild detergent solution. Do not use

any type of abrasive pad, scouring

powder or solvent such as alcohol or

benzine.

Replacing the battery in the remote

Slide out and remove the battery case

and insert a new lithium battery CR2025

with the + side facing up. And then,

slide the battery case back in.

1

2

1 Keep pushing

2 Pull out

CAUTION

Danger of explosion if battery is

incorrectly replaced. Replace the battery

only with the same or eqivalent type

recommended by the manufacturer.

Discard used batteries according to the

manufacturer’s instructions.

On transport

When transporting the player, be sure to

attach the protective bar onto the disc

tray, and secure it with adhesive tape as

it was at the time you purchased the

player. For details about attaching the

protective bar, see page 5.

Before transporting the player, be sure to

remove any CD that may be loaded.

If you have any questions or

problems concerning your player,

please consult your nearest Sony

dealer.

A lithium battery CR2025

3

GB

Welcome!

Thank you for purchasing the Sony

Compact Disc Player. Before operating

the unit, please read this manual

thoroughly and retain it for future

reference.

About This Manual

The instructions in this manual are for

model CDP-LSA1.

Conventions

•Instructions in this manual describe

the controls on the player.

You can also use the controls on the

remote if they have the same or

similar names as those on the player.

•The following icons are used in this

manual:

Z

Indicates that you can do the

task using the remote.

z

Indicates hints and tips for

making the task easier.

TABLE OF CONTENTS

Getting Started

Unpacking4

Hooking Up the System4

Basic Operations

Playing a CD6

Playing CDs

Using the Display8

Locating a Specific Track or a Particular Point in a Track11

Playing Tracks Repeatedly Z12

Playing in Random Order (Shuffle Play) Z13

Creating Your Own Programme (Programme Play) Z13

Other Functions

Adjusting the Brightness of the Display Z15

Setting the Player to Turn Off Automatically

(Power Save Function) Z16

About i.LINK16

Additional Information

Notes on CDs19

Troubleshooting19

Specifications20

Display Messages20

Index

Index21

4

GB

Getting Started

Hooking Up the System

Overview

This section describes how to hook up the CD player to

a receiver or other components such as an MD deck.

Be sure to turn off the power to all components before

you start connecting them.

v v

ç

≈

i.LINK

S200

:

i.LINK

S200

b

* You can connect components to either i.LINK S200

connector.

What cords will I need?

i.LINK connecting cable (supplied) (1)

Unpacking

Check that you have received the following items:

• i.LINK connecting cable (1)

• Remote commander (remote) (1)

Before using the supplied remote

The supplied remote already contains a battery. Before

using the remote, pull out the insulating sheet to allow

the power to flow from the battery.

To avoid battery leakage

If you don’t use the remote for an extended period of time,

remove the battery to avoid possible damage from battery

leakage and corrosion.

z When to replace the battery

Under normal conditions, the battery should last for

about six months. When the remote no longer operates

the player, replace the battery with a new one.

Notes on lithium battery

• Keep the lithium battery out of the reach of the children.

Should the battery be swallowed, immediately consult a

doctor.

• Wipe the battery with a dry cloth to assure a good contact.

• Be sure to observe the correct polarity when inserting the

battery.

• Do not hold the battery with metallic tweezers, otherwise a

short-circuit may occur.

WARNING

Battery may explode if mistreated.

Do not recharge, disassemble, or dispose of in fire.

CDP-LSA1

Receiver*

Signal flow

To a mains

Getting Started

MD deck, etc.*

Getting Started

5

GB

Getting Started

Hookups

Connecting the player to a receiver

Connect the receiver to the i.LINK S200 connector with

the i.LINK connecting cable (supplied). Make sure all

connections are firm. If not, there will be no sound

from the speakers.

v v

ç

:

i.LINK S200

≈

Notes

• Do not connect the mains lead of any component until all

the connections have been completed.

• Do not allow any metal object to enter the i.LINK S200

connector as this may short-circuit the connector and

damage the components.

z The other i.LINK S200 connector can be used to

connect other components

The following i.LINK components can be used with the

player:

• STR-LSA1 receiver

• MDS-LSA1 MD deck

Be sure to use the Sony i.LINK S200 connecting cable

(4 pins - 4 pins).

z For general information about i.LINK

See “About i.LINK” on page 16.

Connecting the mains lead

Connect the mains lead to a mains.

Removing the protective bar

Remove the attached protective bar and retain it for

use when transporting the player at a later time.

DISPLAY

§

When you connect the mains lead to a mains, the disc

tray will close automatically after a while.

Where do I go next?

Now you’re ready to use your player.

If you aren’t familiar with how to play CDs, go to the section

“Playing a CD” on page 6.

Then, go to the following sections for other operations.

ReceiverCDP-LSA1

Signal flow

Attaching the protective bar

When transporting the player, be sure to attach the

protective bar (which you removed at the time you

unpacked the player) onto the disc tray, and use

adhesive tape to secure the bar. If you fail to

attach the protective bar, the player may be

damaged during transport.

1 With the disc tray opened, disconnect the

mains lead.

2 Place the protective bar on the disc tray as

shown below.

DISPLAY

§ x

·

3 Push the disc tray with your fingers to close it.

§

DISPLAY

Slowly push both sides of the disc tray as

shown above.

4 Secure the protective bar with adhesive tape.

DISPLAY

§

6

GB

Basic Operations

Playing a CD

3 4

2

STANDBY

DISPLAY

1/u

=+

§ px·P

1

Turn on the receiver and select the CD player as the audio

source.

2

Press 1/u to turn on the player.

The STANDBY indicator turns off.

3

Press § and place a CD on the tray.

DISPLAY

1/u

§

4

Press ·P.

The disc tray closes and the player plays all the tracks once each

in sequence (Continuous Play).

Adjust the volume on the receiver.

Place the CD with the label side up. When

you play a CD single (8 cm CD), place it on

the inner circle of the tray.

• See pages 4 - 5 for hookup

information.

Basic Operations

Note

In step 3, do not place more than

one CD on the tray at the same

time.

If you do so, the discs and/or the

player may be damaged.

Basic Operations

7

GB

Basic Operations

To stop playback

Press p.

p·P

§

=/+

DISPLAY

1/u

=+

§ px·P

To Press

Pause ·P

Resume play after pause ·P

Go to the next track +

Go back to the preceding track =

Stop play and remove the CD §

8

GB

Playing CDs

Using the Display

You can use the display to check a variety of

information about the disc.

1/u

=+

§ p·P

DISPLAY

SCROLL

YES

MENU/NO

=/+

1/u

=+0 )

(P p

789

>10

10

/0

123

456

Checking the total number of the tracks

and the total playing time of the CD

The total number of tracks and the total playing time

appear in the display before you start playing.

12 58m 41s

z If you press DISPLAY in Programme Play mode before

you start playing

Each time you press DISPLAY, the display changes as

shown below.

12 58m 41s

12 Step4

* The original display returns a second later, even if

you do not press the DISPLAY button.

Total playing timeTotal number of tracks

Information displayed while playing a disc

The current track number and elapsed playing time of

the track appear in the display while playing a disc.

1 3m 29s

Checking the remaining playing time

Each time you press DISPLAY while playing a disc, the

display changes as shown below.

1  3m 29s

55

-

-m12s

1  1m 13s

* This does not appear in Programme Play mode or

Shuffle Play mode.

Elapsed playing timeCurrent track number

Press

Remaining playing time of the disc*

Playing CDs

Last track programmed and total playing

time

Press

Current track number and elapsed playing

time of the track

Current track number and remaining playing

time of the track

Press

Last track programmed and selection

number

Press

Playing CDs

9

GB

Playing CDs

(Continued)

Checking the information on CD TEXT discs

CD TEXT discs contain information such as disc titles

and artist names. This information is recorded in

empty spaces that are normally unused on

conventional CDs. The CD TEXT information of the

disc appears in the display so that you can check the

current disc tittle, artist name and track tittle. When

the player detects CD TEXT discs, “CD-TEXT”

indication appears in the display. If the CD TEXT has

multi-language capability, “CD-TEXT” and “MULTI”

indications appear in the display. To check the

information in another language, see “Checking the

information on CD TEXT discs in other languages” on

page 10.

Each time you press DISPLAY, the display changes as

shown below.

• Before you start playing

2185m41s

NOSY SHIT

NOSY NDBA

z If you press DISPLAY in Programme Play mode before

you start playing

See page 8.

Press

Total number of tracks and total playing time

Press

Artist name

Disc title

• While playing a disc

1  3m 29s

s

tiWh em

55

-

-m12

1  1m 13

* This does not appear in Programme Play mode or

Shuffle Play mode.

If a title or name has more than 14 characters, the first

14 characters will appear in the display after the entire

title or name has scrolled across the display once.

z You can check a title or name with more than 14

characters

Z

Press SCROLL.

The title or name scrolls across the display. Then the first

14 characters will appear in the display.

Notes

• Depending on the disc, the display may not show all the

characters.

• This player can display only the disc titles, track titles and

artist names. Other information on CD TEXT discs cannot

be displayed.

Press

Current track title

Press

Remaining playing time of the disc*

Current track number and playing time of

the track

Current track number and remaining playing

time of the current track

10

GB

Playing CDs

Checking the information on CD TEXT discs

in other languages Z

If the player detects a CD TEXT disc with multi-

language capability, “CD-TEXT” and “MULTI” appear

in the display. This type of CD allows you to change

the displayed language.

1 Before playing a CD TEXT disc, press MENU/NO.

“Select Lang” appears, followed by the display

information in the currently selected language.

2 Press YES.

“English” flashes in the display.

3 Press =/+ repeatedly until the language you

want appears in the display.

4 Press YES to select the language.

“TEXT Reading” appears momentarily. Then the

display information appears in the new selected

language.

5 Press DISPLAY repeatedly until the information

you want to check appears (see page 9).

z To check the currently selected language while

playing a disc

Press MENU/NO while playing a disc.

The currently selected language appears in the display

after “Show Lang” is displayed.

To return to the original display, press MENU/NO

again.

Notes

• The selected language mode remains in effect even if you

turn off the player or disconnect the mains lead from the

mains.

• The languages that you can select differ according to the

disc.

Other display information

When the player is selected as the audio source by

other Sony component featuring the PING function

connected through the i.LINK connecting cable,

“( ( 9 9” appears in the display of the player.

Note that this indication does not appear when the

STANDBY indicator is on.

z When the H.A.T.S. indicator lights up

This means the H.A.T.S. function is activated on the

receiver.

The H.A.T.S. (High-quality digital Audio Transmission

System) function on the receiver causes digital audio

signals output from a CD player or another source (e.g.,

an MD deck) to be momentarily stored in a buffer in the

receiver prior to output. This reduces jitter that

sometimes occurs during digital audio transmission.

Playing CDs

11

GB

Playing CDs

To locate Do the following

The beginning of the

next or succeeding

tracks

Press + repeatedly until you find

the track.

The beginning of the

current or preceding

tracks

Press = repeatedly until you find

the track.

A specific track

directly Z

Enter the track number with the

numeric buttons.

A particular point in

a track while

monitoring the

sound Z

Press down ) (forward) or 0

(backward) until you find the point.

Quickly a particular

point in a track by

observing the

display Z

Press down ) (forward) or 0

(backward) with the player paused

until you find the point. There will be

no sound output during this operation.

z To specify a track numbered over 10

Z

Press >10 first, then the corresponding numeric buttons.

To enter “0,” press 10/0.

Example: To enter track number 30

Press >10 first, then 3 and 10/0.

Note

If you reach the end of the disc while pressing ) on the

remote, “– OVER –” appears in the display. Press 0 on the

remote to go back.

Locating a Specific Track or a

Particular Point in a Track

Using the AMS (Automatic Music Sensor) buttons or

the numeric buttons on the remote, you can quickly

locate any point in a track or any track on the disc

while playing a disc.

1/u

=+

§ p·P

=/+

0/)

=/+

>10

1/u

=+0 )

(P p

789

>10

10

/0

123

456

Numeric

buttons

12

GB

Playing CDs

Playing Tracks Repeatedly Z

You can play tracks repeatedly in any play mode.

A˜B

(

REPEAT

CLEAR

1/u

=+0 )

(P p

789

>10

10

/0

123

456

While playing a disc, press REPEAT CLEAR

repeatedly until “REPEAT” appears in the display.

The player repeats the tracks as follows:

If the play mode is The player repeats

Continuous Play (page 6) All the tracks

Shuffle Play (page 13) All the tracks in random order

Programme Play (page 13) The programmed tracks

To cancel Repeat Play

Press REPEAT CLEAR repeatedly until “REPEAT” and

“REPEAT 1” disappear.

Repeating the current track (Repeat 1)

You can repeat only the current track in any play

mode.

While the track you want is being played, press

REPEAT CLEAR repeatedly until “REPEAT 1” appears

in the display.

To cancel Repeat 1

Press REPEAT CLEAR repeatedly until “REPEAT” and

“REPEAT 1” disappear.

Repeating a Specific Portion

(A˜B Repeat)

You can play a specific portion in a track repeatedly.

This might be useful when you want to memorize

lyrics.

Note that you cannot repeat a portion that extends over

two tracks.

1 While playing a disc, press A˜B at the starting

point of the portion you want to play repeatedly

(point A).

“A-” of “REPEAT A-” flashes in the display.

2 When you reach the ending point of the portion

(point B), press A˜B again.

“REPEAT A-B” appears and the player plays the

specified portion repeatedly.

To cancel A˜B Repeat

Press REPEAT CLEAR.

Moving the starting point

By moving the starting point, you can change the specified

portion to one that immediately follows.

1 Press A˜B while the player is repeating the specific

portion.

The ending point B becomes the new starting point A and

“A-” of “REPEAT A-” flashes in the display.

2 When you reach the new ending point (point B), press

A˜B again.

“REPEAT A-B” appears and the player plays the newly

specified portion repeatedly.

z To go back to the starting point A

Press ( while playing a track with A˜B Repeat.

Playing CDs

13

GB

Playing CDs

Playing in Random Order

(Shuffle Play) Z

You can use this function to “shuffle” tracks and play

them in a random order.

(

PLAY MODE

1/u

=+0 )

(P p

789

>10

10

/0

123

456

1 Press PLAY MODE repeatedly until “SHUFFLE”

appears in the display.

2 Press ( to start Shuffle Play.

The

indication appears while the player is

“shuffling” the tracks.

To cancel Shuffle Play

While the player is stopped, press PLAY MODE repeatedly

until “SHUFFLE” disappears.

Note

The play mode cannot be changed while playing a disc even if

you press the PLAY MODE button.

Creating Your Own Programme

(Programme Play) Z

You can make a programme that plays up to 25

selected tracks in the order that you want.

(

PLAY MODE

CLEAR

=/+

>10

1/u

=+0 )

(P p

789

>10

10

/0

123

456

1 Before you start playing, press PLAY MODE

repeatedly until “PROGRAM” appears in the

display.

2 Use the numeric buttons to enter the track

numbers you want to include in the programme, in

the order you want.

Example: To programme the tracks 2, 8 and 5.

Press the numeric buttons in the order

2, 8 and 5.

5 13m 18s

To enter a track with a number over 10

Use >10 button (see page 11).

If you enter the wrong track number

Press CLEAR, then enter the correct track number.

3 Press ( to start Programme Play.

To cancel Programme Play

While the player is stopped, press PLAY MODE repeatedly

until “PROGRAM” disappears.

Last track programmed

Numeric

buttons

Total playing time

(Continued)

14

GB

Playing CDs

z The programme remains in memory until you erase it

(see below) or press §

The programme is not affected by the ending of the

programme or by the selection of another play mode.

Notes

• “- -m - -s” appears in the display if the total playing time

exceeds 100 minutes.

• “Step Full” appears in the display when you try to add a

track to a programme which already contains 25 tracks.

• The play mode cannot be changed while playing a disc

even if you press the PLAY MODE button.

Changing the track order

You can change the order of the tracks in your

programme before you start playing.

To Do the following

Erase the last track in the

programme

Press CLEAR. Each time you

press the button, the last track

will be erased.

Add tracks to the end of the

programme

Press the numeric buttons to

enter the track numbers you

want to add.

Erase the entire programme

completely

Press down CLEAR until the

total number of tracks and the

total playing time appear. To

create a new programme,

repeat the programming

procedure.

15

GB

Other FunctionsOther Functions

Adjusting the Brightness of

the Display Z

You can select one of four brightness levels for the

display window. The operation buttons on the player

(§, ·P, and p) turn off when “Dimmer3” or

“Dimmer4” is selected.

YES

MENU/NO

=/+

1/u

=+0 )

(P p

789

>10

10

/0

123

456

1 Before playing a disc, press MENU/NO repeatedly

until “Setup Menu” appears in the display.

2 Press =/+ until “Dimmer” appears, then

press YES.

3 Press =/+ repeatedly to select the brightness

level, then press YES.

When you select The display is

Dimmer1 (default setting) Fully lit and the operation

buttons are on.

Dimmer2 Dimmer and the operation

buttons are on.

Dimmer3 Dimmer and the operation

buttons are off.

Dimmer4 Turned off and the

oepration buttons are off.

4 Press MENU/NO.

z If you do any operation while the display window is

turned off

The display turns back on (dimly) for several seconds,

and then turns off again.

z If you make menu settings while the display window

is turned off

The display turns back on (dimly) during the menu

setting.

z The brightness level of the display window on the CD

player can be linked to that of the receiver’s display

window

When the i.LINK control function is activated on the

receiver, the brightness level of the display window on

the CD player is automatically set to that of the receiver’s

display window regardless of the setting on the CD

player.

16

GB

Other Functions

Setting the Player to Turn Off

Automatically

(Power Save Function) Z

When the Power Save function is on, the player will

automatically turn off (change to STANDBY) after

several minutes of inactivity.

YES

MENU/NO

=/+

1/u

=+0 )

(P p

789

>10

10

/0

123

456

1 Before playing a disc, press MENU/NO repeatedly

until “Setup Menu” appears in the display.

2 Press =/+ until “Power Save” appears, then

press YES.

3 Press =/+ to select the setting, then press

YES.

To Select

Turn on the Power Save

function

Power Save On

(default setting)

Turn off the Power Save

function

Power Save Off

4 Press MENU/NO.

About i.LINK

This section explains the general specifications and

major features of i.LINK. Read this section before

doing any i.LINK-related operation.

Note that i.LINK connections and operations may vary,

depending on the component. For details regarding

the connection of i.LINK components to this player, see

“Hooking Up the System” on page 4.

i.LINK functions

i.LINK is a serial digital interface that supports the bi-

directional transmission of audio and video signals,

commands, and even component status information.

All that is needed to hook up i.LINK components are

i.LINK connecting cables. Audio and video

components connected within an i.LINK configuration

can be used to perform a wide range of operations and

data exchanges that is sure to expand as the number

and variety of i.LINK components grow.

Since i.LINK allows data to be transmitted from one

component to other components to which it is not

directly connected, there is no need to pay attention to

connection order. However, due to differences in

characteristics or specifications, operation of or data

exchange with certain i.LINK components may not be

possible, even when they are connected.

z What is i.LINK?

i.LINK is a trademark proposed by Sony Corporation

and accepted by companies throughout the world as an

easy-to-remember name for the IEEE 1394 world

standard of the Institute of Electrical and Electronics

Engineers.

17

GB

Other Functions

i.LINK connections

The use of i.LINK cables to connect i.LINK components

as shown below is called a “daisy chain” configuration.

Data can be transmitted between any two

components even if they are indirectly connected.

Branch connections

• Any i.LINK component with three or more i.LINK

connectors can serve as a branch point.

• Up to 63 i.LINK components can be connected in a

single configuration. However, the maximum

number of components that can be daisy-chained in

a single route is 17 (i.e., a maximum of 16 i.LINK

connecting cables in a row). Each i.LINK cable used

in a single route is called a “hop.” For example,

there are 6 hops in the route between A and C in the

illustration below, and 3 hops in the route between A

and D.

BA

DC

Each route between A and B; A and C; A and D; B and

C; B and D; and C and D in the illustration above can

have 16 hops (i.e., 17 components).

Loop-connetion

A signal output from one component is transmitted to

all other components. A loop connection should thus

be avoided to prevent the return of a signal to its

source.

Notes

• Some i.LINK components (such as personal computers) do

not transfer signals when they are turned off. Refer to the

operation manual of each component to be connected

before you hook them up.

• The maximum transmission rate of an i.LINK component is

printed near its i.LINK connector. The indications S100,

S200, and S400 refer to maximum transmission rates of 100,

200, or 400 Mbps*, respectively. The actual transmission

rate may be faster or slower, depending on the differences

in transmission rates and specifications among the

connected components.

z What is Mbps?

“Mbps” is an abbreviation for megabits per second. It

indicates the amount of data transmitted per second. For

example, a rate of 200 Mbps means 200 megabits of data

are transmitted in one second.

(Continued)

i.LINK connecting cable

i.LINK component

Correct Incorrect (looped)

18

GB

Other Functions

Establishing a LINC

Before an audio signal can be transmitted between

i.LINK components, a “LINC” must first be established

between the receiving component (of the audio signal)

and the sending component. Establishing a “LINC”

means establishing a logical path for the transmission

of digital audio signals between the two components.

Each logical path has an ID number. Since the

component that sends an audio signal must output the

signal to a path, and the component that receives the

signal must input it from the same path, the path must

be mutually known by both components. During the

establishment of a LINC, the following communication

occurs between the two i.LINK components.

Example

A component establishing a LINC with a CD player in

order to receive an audio signal from the CD player

1 The component that will receive an audio signal

from the CD player sends a request and path

information to the CD player to establish a

transmission path for the audio signal.

1

/

2

?

2 The CD player responds to the component,

agreeing to the establishment of a LINC.

The digital audio signal transmission becomes possible

only after the communication described above has

occurred and a LINC has been established.

The component

that receives

the audio signal

CD player

(sending

component)

19

GB

Additional Information

Notes on CDs

On handling CDs

• To keep the disc clean, handle the disc by its edge. Do not

touch the surface.

• Do not stick paper or tape on the disc.

• Do not expose the disc to direct sunlight or heat sources

such as hot air ducts, nor leave it in a car parked in direct

sunlight as there can be considerable rise in temperature

inside the car.

• Do not use any commercially available stabiliser and/or

disc protector. If you do, the disc and the player may be

damaged.

• After playing a disc, store it in its case.

On placing CDs on the disc tray

• Make sure the disc is positioned securely on the tray’s

circle. If not, it may damage the player or the disc.

On cleaning

• Before playing a disc, clean it with a cleaning cloth. Wipe

the disc from the centre out.

• Do not use solvents such as benzine, thinner, commercially

available cleaners or anti-static spray intended for vinyl

LPs.

Troubleshooting

If you experience any of the following difficulties while

using the player, use this troubleshooting guide to help

you remedy the problem. Should any problem persist,

consult your nearest Sony dealer.

There’s no sound.

/ Check that the player is connected securely.

/ Make sure you operate the receiver correctly.

/ Use the i.LINK connecting cable for 200 Mbps

transmission rate.

The CD does not play.

/ There’s no CD inside the player (“No Disc”

appears). Insert a CD.

/ Place the CD on the disc tray with the label side

up correctly.

/ Clean the CD (see page 19).

/ Moisture has condensed inside the player.

Remove the disc and leave the player turned

on for about an hour (see page 2).

The remote does not function.

/ Remove the obstacles between the remote and

the player.

/ Point the remote at the remote sensor g on the

player.

/ Replace the battery in the remote with a new

one if it is weak (see page 2).

Additional Information

20

GB

Additional Information

Specifications

Compact disc player

Laser Semiconductor laser (λ = 800 nm)

Emission duration: continuous

Inputs/Outputs (i.LINK S200)

i.LINK connector 4 pins - 4 pins (S200)

General

Power requirements 230 V AC, 50/60 Hz

Power consumption 22 W

Dimensions (approx.) (w/h/d)

430 × 70 × 315 mm

incl. projecting parts

Mass (approx.) 4.6 kg

Supplied accessories

i.LINK connecting calbe (4 pins - 4 pins) (1)

Remote commander (remote) (1)

Design and specifications are subject to change without

notice.

Display Messages

The following table explains the various messages that

appear in the display.

Message Error code(s) Cause and/or remedy

CANNOT

LINC

C78:11/C78:12 The player cannot establish

a LINC with a component

because of an existing LINC

between the player and

another component. Cancel

the LINC between the

player and the other

component.

BUS FULL C78:15 The signal bus within the

i.LINK configuration is full

and no more signals can be

output from the player.

Cancel the LINC between

the component and the

player.

LOOP

CONNECT

C78:03 The i.LINK connection is

looped. Check the

connection (see page 17).

NEW

CONNECT

— An i.LINK component has

been connected to or

disconnected from the

i.LINK configuration. Wait

several seconds for the

indication to turn off.

La page charge ...

Sony CDP-LSA1 Manuel utilisateur

Sony CDP-LSA1 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents