Toro Flex-Force Power System 60V MAX Axial Blower Manuel utilisateur

Catégorie
Souffleurs / sécheurs d'air
Taper
Manuel utilisateur
Form No. 3460-490 Rev A
Flex-Force Power System
60V MAX Axial
Blower
51820, 51820T
Soplador Axial Flex-Force Power System
60V MAX51820, 51820T
Soufeur axial Flex-Force Power System
60 V MAX51820, 51820T
www .T oro.com.
*3460-490*
Form No. 3460-487 Rev A
Flex-Force Power System
60V
MAX Axial Blower
Model No. 51820 —Serial No. 323000001 and Up
Model No. 51820T —Serial No. 323000001 and Up
Register at www .T oro.com.
Original Instructions (EN)
*3460-487*
For assistance, please see
www .T oro.com/support
for instructional videos
or contact 1-888-384-9939
before returning this
product.
W ARNING
CALIFORNIA
Proposition 65 W arning
The power cord on this product contains
lead, a chemical known to the State
of California to cause birth defects
or other reproductive harm. W ash
hands after handling.
Use of this product may cause exposure
to chemicals known to the State of
California to cause cancer , birth defects,
or other reproductive harm.
Introduction
This blower is intended to be used by residential
homeowners to move leaf-like debris as needed
outdoors. It is designed to use T oro 60V lithium-ion
battery packs. These battery packs are designed
to be charged only by T oro 60V lithium-ion battery
chargers. Using these products for purposes other
than their intended use could prove dangerous to you
and bystanders.
Model 51820T does not include a battery or a
charger .
Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. Y ou are responsible for
operating the product properly and safely .
V isit www .T oro.com for more information, including
safety tips, training materials, accessory information,
help nding a dealer , or to register your product.
Whenever you need service, genuine T oro parts, or
additional information, contact an Authorized Service
Dealer or T oro Customer Service and have the model
and serial numbers of your product ready . Figure 1
identies the location of the model and serial numbers
on the product. W rite the numbers in the space
provided.
Important: W ith your mobile device, you can
scan the QR code (if equipped) on the serial
number plate to access warranty , parts, and other
product information.
g426535
Figure 1
1. Model and serial number location.
Model No.
Serial No.
© 2023—The T oro® Company
81 1 1 L yndale A venue South
Bloomington, MN 55420
2
Contact us at www .T oro.com.
Printed in V ietnam
All Rights Reserved
Safety-Alert Symbol
The safety-alert symbol ( Figure 2 ) shown in this
manual and on the machine identies important safety
messages that you must follow to prevent accidents.
g000502
Figure 2
Safety-alert symbol
The safety-alert symbol appears above information
that alerts you to unsafe actions or situations and
is followed by the word DANGER ,W ARNING , or
CAUTION .
DANGER indicates an imminently hazardous situation
which, if not avoided, will result in death or serious
injury .
W ARNING indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury .
CAUTION indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury .
This manual uses two other words to highlight
information. Important calls attention to special
mechanical information and Note emphasizes general
information worthy of special attention.
Safety
IMPORT ANT SAFETY
INSTRUCTIONS
W ARNING
When using electric gardening tools, always
read and follow basic safety warnings and
instructions to reduce the risk of re, electric
shock, and personal injury , including the
following:
Read All Instructions
I. T raining
1. The operator of the tool is responsible for any
accidents or hazards occurring to others or their
property .
2. Do not allow children to use or play with the
tool, battery pack, or the battery charger; local
regulations may restrict the age of the operator .
3. Do not allow children or untrained people to
operate or service this device. Allow only people
who are responsible, trained, familiar with the
instructions, and physically capable to operate
or service the device.
4. Before using the tool, battery pack, and battery
charger , read all the instructions and cautionary
markings on these products.
5. Become familiar with the controls and proper use
of the tool, battery pack, and battery charger .
II. Preparation
1. Keep bystanders and children away from the
operating area.
2. Use only the battery pack specied by T oro.
Using other accessories and attachments may
increase the risk of injury and re.
3. Plugging the battery charger into an outlet that is
not 120 V can cause a re or electric shock. Do
not plug the battery charger into an outlet other
than 120 V . For a dif ferent style of connection,
use an attachment plug adapter of the proper
conguration for the power outlet if needed.
4. Do not use a damaged or modied battery
pack or battery charger , which may exhibit
unpredictable behavior that results in re,
explosion, or risk of injury .
5. If the supply cord to the battery charger is
damaged, contact an Authorized Service Dealer
to replace it.
6. Charge the battery pack with only the battery
charger specied by T oro. A charger suitable for
3
one type of battery pack may create a risk of re
when used with another battery pack.
7. Charge the battery pack in a well-ventilated area
only .
8. Follow all charging instructions and do
not charge the battery pack outside of the
temperature range specied in the instructions.
Otherwise, you may damage the battery pack
and increase the risk of re.
9. Do not operate the tool without all guards and
other safety protective devices in place and
functioning properly on the tool.
10. Dress properly—W ear appropriate clothing,
including eye protection; long pants; substantial,
slip-resistant footwear; and hearing protection.
T ie back long hair and do not wear loose clothing
or loose jewelry that can get caught in moving
parts. W ear a dust mask in dusty operating
conditions.
III. Operation
1. A void dangerous environments—Do not use the
tool in rain or in damp or wet locations.
2. Use the proper tool for your application—Using
the tool for purposes other an its intended use
could prove dangerous to you and bystanders.
3. Prevent unintentional starting—Ensure that the
switch is in the O FF position before connecting
to the battery pack and handling the tool. Do
not carry the tool with your nger on the switch
or energize the tool with the switch in the O N
position.
4. Operate the tool only in daylight or good articial
light.
5. Remove the battery pack from the tool before
adjusting it or changing accessories.
6. Keep your hands and feet away from the
opening and all moving parts.
7. Stop the tool, remove the battery pack from the
tool, and wait for all movement to stop before
adjusting, servicing, cleaning, or storing the tool.
8. Remove the battery pack from the tool whenever
you leave it unattended.
9. Do not force the tool—Allow the tool to do the
job better and safer at the rate for which it was
designed.
10. Do not overreach—Keep proper footing and
balance at all times, especially on slopes. W alk,
never run with the tool.
1 1. Stay alert—W atch what you are doing and use
common sense when operating the tool. Do not
use the tool while ill, tired, or under the inuence
of alcohol or drugs.
12. Ensure that the ventilation openings are kept
clear of debris.
13. Do not insert any object into the opening or
use the tool with a blocked opening. Keep the
opening free from dust, lint, hair , or anything
else that could reduce the air ow .
14. Use extra care when using the tool to clean
stairways.
15. Under abusive conditions, the battery pack may
eject liquid; avoid contact. If you accidently
come into contact with the liquid, ush with
water . If the liquid contacts your eyes, seek
medical help. Liquid ejected from the battery
pack may cause irritation or burns.
16. Do not expose a battery pack or tool to re or
excessive temperature. Exposure to re or
temperature above 130°C (265°F) may cause
explosion.
17. CAUTION—A mistreated battery pack may
present a risk of re, explosion, or chemical
burn.
Do not disassemble the battery pack.
Replace the battery pack with a genuine
T oro battery pack only; using another type of
battery pack may cause a re or risk of injury .
Keep battery packs out of the reach of
children and in the original packaging until
you are ready to use them.
4
IV . Maintenance and Storage
1. Maintain the tool with care—Keep it clean and
in good repair for best performance and to
reduce the risk of injury . Follow the instructions
for lubricating and changing accessories. Keep
handles dry , clean, and free from oil and grease.
2. When the battery pack is not in use, keep it
away from metal objects such as paper clips,
coins, keys, nails, and screws that can make
a connection from one terminal to another .
Shorting the battery terminals may cause burns
or a re.
3. Keep your hands and feet away from moving
parts.
4. Stop the tool, remove the battery pack from the
tool, and wait for all movement to stop before
adjusting, servicing, cleaning, or storing the tool.
5. Check the tool for damaged parts—If there
are damaged guards or other parts, determine
whether it will operate properly . Check for
misaligned and binding moving parts, broken
parts, mounting, and any other condition that
may af fect its operation. Unless indicated in the
instructions, have an Authorized Service Dealer
repair or replace a damaged guard or part.
6. Keep all fasteners on the tool tight.
7. Do not attempt to service or repair the tool,
battery pack, or battery charger except as
indicated in the instructions. Have an Authorized
Service Dealer perform service using identical
replacement parts to ensure that the product is
safely maintained.
8. Store an idle tool indoors in a place that is dry ,
secure, and out of the reach of children.
SA VE THESE
INSTRUCTIONS
5
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger . Replace any decal that is damaged or missing.
decal137-9454
137-9454
1. Read the Operator ’ s
Manual .
3. Keep away from open re
or ames.
2. Call2Recycle
®
battery
recycling program
4. Do not expose to rain.
decal137-9461
137-9461
1. Battery charge status
decal137-9462
137-9462
decal137-9463
137-9463
1. The battery pack is charging.
2. The battery pack is fully charged.
3. The battery pack is over or under the appropriate temperature range.
4. Battery pack charging fault
6
decal140-8496
140-8496
1. W arning—read the
Operator ’ s Manual ; stay
away from moving parts;
keep all guards and
shields in place; wear eye
protection; do not expose
to rain.
3. Thrown object
hazard—keep bystanders
away .
2. W arning—keep
bystanders away from the
machine in all directions.
decal140-8497
140-8497
1. W arning—read the
Operator ’ s Manual ; stay
away from moving parts;
keep all guards and
shields in place; wear eye
protection; do not expose
to rain.
3. Thrown object
hazard—keep bystanders
away .
2. W arning—keep
bystanders away from the
machine in all directions.
7
Setup
Important: The battery pack is not fully charged
when you purchase it. Before using the tool for
the rst time, refer to Charging the Battery Pack
( page 12 ) .
Mounting the Battery
Charger (Optional)
If desired, mount the battery charger securely on a
wall using the wall-mount key holes on the back of
the charger .
Mount it indoors (such as a garage or other dry place),
near a power outlet, and out of the reach of children.
Refer to Figure 3 for assistance in mounting the
charger .
Slide the charger over the appropriately positioned
hardware to secure the charger in place (hardware
not included).
g290534
Figure 3
Assembling the Blower
Slide the blower tube onto the blower housing. Y ou
may need to press down on the tube latch for the
blower tube to lock into place ( Figure 4 ).
g273147
Figure 4
1. T ube latch
8
Product Overview
g335835
Figure 5
1. Battery and battery cavity 5. Blower tube latch
2. T urbo boost button 6. Blower tube
3. Speed lock
7. V ariable-speed trigger
4. Handle knob
g362427
Figure 6
1. Battery charger Model
88602 (included with
Model 51820)
2. Battery pack Model 88625
(included with Model
51820)
Specications
Model 51820, 51820T
Rated V oltage
60V DC maximum, 54 VDC
nominal usage
Charger T ype
T oro 60V lithium-ion chargers
Battery T ype T oro 60V lithum-ion batteries
Appropriate T emperature Ranges
Charge/ store the battery pack
at
5°C (41°F) to 40°C (104°F)*
Use the battery pack at
-30°C (-22°F) to 49°C (120°F)
Use the blower at
0°C (32°F) to 49°C (120°F)
*Charging time will increase if you do not charge the
battery within this range.
Store the tool, battery pack, and battery charger in an
enclosed clean, dry area.
Attachments/Accessories
A selection of T oro approved attachments and
accessories is available for use with the machine
to enhance and expand its capabilities. Contact
your Authorized Service Dealer or authorized T oro
distributor or go to www .T oro.com for a list of all
approved attachments and accessories.
T o ensure optimum performance and continued safety
certication of the machine, use only genuine T oro
replacement parts and accessories. Replacement
parts and accessories made by other manufacturers
could be dangerous.
9
Operation
W ARNING
The blower can throw debris, possibly
causing serious personal injury to you or
bystanders.
• Do not blow hard objects, such as nails or
bolts.
• Do not operate the blower near bystanders
or pets.
• Be careful of blowing direction (i.e.,
blow away from bystanders, windows,
automobiles, etc.). Only use as much
speed as required.
• Use extra care when cleaning debris from
stairs or other tight areas.
Starting the Blower
Important: Use the battery pack only in
temperatures that are within the appropriate
range; refer to Specications ( page 9 ) .
1. Make sure that the vents on the blower are clear
of any dust and debris.
2. Align the cavity on the battery pack with the
tongue in the handle housing ( Figure 7 ).
3. Grasp the handle, and push the battery pack
into the handle until the latch locks into place
(Figure 7 ).
g273146
Figure 7
1. Battery latch
4. T o start the blower , squeeze the variable-speed
trigger ( Figure 8 ).
Note: Engage the speed lock to keep the
machine on without pressing the variable-speed
trigger ( Figure 8 ).
g267241
Figure 8
1. Speed lock
4. Battery latch
2. T urbo boost button 5. Blower venting areas
3. V ariable-speed trigger
10
Adjusting the Air Speed of
the Blower
T o achieve maximum performance (air speed), fully
depress the variable-speed trigger , then press and
hold the turbo boost button for the desired amount of
time ( Figure 8 ).
T o adjust the air speed as you blow , use the
variable-speed trigger ( Figure 8 ).
T o maintain the current air speed, engage the speed
lock ( Figure 8 ).
Shutting Off the Blower
T o shut of f the blower , disengage the speed lock (if in
use) and release the variable-speed trigger ( Figure 8 ).
Important: After stopping the blower , do not
leave the speed lock engaged with the battery
pack in the blower .
Whenever you are not using the blower or are
transporting the blower to or from the work area,
remove the battery pack.
Removing the Blower T ube
Press down on the tab latch to separate the blower
tube from the blower ( Figure 9 ).
g273159
Figure 9
1. T ube latch
Removing the Battery from
the Blower
Press the battery latch to release the battery pack and
slide the battery pack out of the blower ( Figure 10 ).
g267488
Figure 10
1. Battery latch
1 1
Charging the Battery Pack
Important: The battery pack is not fully charged
when you purchase it. Before using the tool for
the rst time, place the battery pack in the charger
and charge it until the LED display indicates the
battery pack is fully charged. Read all safety
precautions.
Important: Charge the battery pack only in
temperatures that are within the appropriate
range; refer to Specications ( page 9 ) .
Note: At any time, press the battery-charge-indicator
button on the battery pack to display the current
charge (LED indicators).
1. Make sure that the vents on the battery and
battery charger are clear of any dust and debris.
g290533
Figure 1 1
1. Battery pack cavity
5. LED indicators (current
charge)
2. Battery pack venting areas 6. Handle
3. Battery pack terminals
7. Charger LED indicator
light
4. Battery-charge-indicator
button
8. Charger venting areas
2. Line up the cavity in the battery pack ( Figure 1 1 )
with the tongue on the charger .
3. Slide the battery pack into the charger until it is
fully seated ( Figure 1 1 ).
4. T o remove the battery pack, slide the battery
backward out of the charger .
5. Refer to the following table to interpret the LED
indicator light on the battery charger .
Indicator
light
Indicates
Of f
No battery pack inserted
Green
blinking
Battery pack is charging
Green
Battery pack is charged
Red
Battery pack and/or battery charger is over or under
the appropriate temperature range
Red
blinking
Battery pack charging fault*
*Refer to T roubleshooting ( page 14 ) for more
information.
Important: The battery can be left on the charger
for short periods between uses.
If the battery will not be used for longer periods,
remove the battery from the charger; refer to
Storage ( page 13 ) .
12
Storage
Important: Store the tool, battery pack, and
charger only in temperatures that are within the
appropriate range; refer to Specications ( page 9 ) .
Important: If you are storing the battery pack for
the off-season, remove the battery pack from the
tool and charge the battery pack until 2 or 3 LED
indicators turn green on the battery . Do not store
a fully charged or fully depleted battery . When you
are ready to use the tool again, charge the battery
pack until the left indicator light turns green on
the charger or all 4 LED indicators turn green on
the battery .
Disconnect the product from the power supply
(i.e., remove the plug from the power supply or the
battery pack) and check for damage after use.
Do not store the tool with the battery pack installed.
Clean all foreign material from the product.
When not in use, store the tool, battery pack, and
battery charger out of the reach of children.
Keep the tool, battery pack, and battery charger
away from corrosive agents, such as garden
chemicals and de-icing salts.
T o reduce the risk of serious personal injury , do
not store the battery pack outside or in vehicles.
Store the tool, battery pack, and battery charger
in an enclosed clean, dry area.
Preparing the Battery Pack
for Recycling
Important: Upon removal, cover the terminals of
the battery pack with heavy-duty adhesive tape.
Do not attempt to destroy or disassemble the
battery pack or remove any of its components.
Lithium-ion battery packs labeled with the
Call2Recycle seal can be recycled at any
participating retailer or battery recycling
facility in the Call2Recycle program (US
and Canada only). T o locate a participating
retailer or facility closest to you, please call
1-800-822-8837 or visit www .call2recycle.org.
If you cannot locate a participating retailer or
facility nearby , or if your rechargeable battery
is not labeled with the Call2Recycle seal,
please contact your local municipality for more
information on how to responsibly recycle the
battery . If you are located outside of the US
and Canada, please contact your authorized
T oro distributor .
13
T roubleshooting
Perform only the steps described in these instructions. All further inspection, maintenance, and repair work
must be performed by an authorized service center or a similarly qualied specialist if you cannot solve the
problem yourself.
Always remove the battery from the tool when troubleshooting, inspecting, maintaining, or cleaning the tool.
Problem
Possible Cause Corrective Action
1. The battery is not fully installed in the
tool.
1. Remove and then replace the battery
into the tool, making sure that it is fully
installed and latched.
2. The battery pack is not charged.
2. Remove the battery pack from the tool
and charge it.
3. The battery pack is damaged. 3. Replace the battery pack.
The tool does not start.
4. There is another electrical problem
with the tool.
4. Contact an Authorized Service Dealer .
1. The battery pack charge capacity is
too low .
1. Remove the battery pack from the tool
and fully charge the battery pack.
The tool does not reach full power .
2. The air vents are blocked.
2. Clean the air vents.
1. There is moisture on the leads of the
battery pack.
1. Allow the battery pack to dry or wipe it
dry .
2. The battery is not fully installed in the
tool.
2. Remove and then replace the battery
in the tool, ensuring that it is fully
installed and latched.
The tool does not run or does not run
continuously .
3. The battery pack is low on charge.
3. Charge the battery pack.
The speed lock does not hold when
engaged.
1. The speed lock screw is loose. 1. T ighten the speed lock screw by
turning the speed lock screw ¼ turn. If
the speed lock still does not hold when
engaged, turn the speed lock screw an
additional ¼ turn.
The battery pack loses charge quickly . 1. The battery pack is over or under the
appropriate temperature range.
1. Move the battery pack to a place
where it is dry and the temperature is
between 5°C (41°F) and 40°C (104°F).
1. The battery charger is over or under
the appropriate temperature range.
1. Unplug the battery charger and move
it to a place where it is dry and the
temperature is between 5°C (41°F)
and 40°C (104°F).
The battery charger is not working.
2. The outlet that the battery charger is
plugged into does not have power .
2. Contact your licensed electrician to
repair the outlet.
The LED indicator light on the battery
charger is red.
1. The battery charger and/or battery
pack is over or under the appropriate
temperature range.
1. Unplug the battery charger and move
the battery charger and battery pack
to a place where it is dry and the
temperature is between 5°C (41°F)
and 40°C (104°F).
14
Problem
Possible Cause Corrective Action
1. There is an error in the communication
between the battery pack and the
charger .
1. Remove the battery pack from the
battery charger , unplug the battery
charger from the outlet, and wait 10
seconds. Plug the battery charger into
the outlet again and place the battery
pack on the battery charger . If the LED
indicator light on the battery charger is
still blinking red, repeat this procedure
again. If the LED indicator light on
the battery charger is still blinking red
after 2 attempts, properly dispose of
the battery pack at a battery recycling
facility .
The LED indicator light on the battery
charger is blinking red.
2. The battery pack is weak.
2. Properly dispose of the battery pack at
a battery recycling facility .
15
California Proposition 65 W arning Information
What is this warning?
Y ou may see a product for sale that has a warning label like the following:
W ARNING: Cancer and Reproductive Harm—www .p65W arnings.ca.gov .
What is Prop 65?
Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into
California. It mandates that the Governor of California maintain and publish a list of chemicals known to cause cancer , birth defects, and/or other
reproductive harm. The list, which is updated annually , includes hundreds of chemicals found in many everyday items. The purpose of Prop 65 is to
inform the public about exposure to these chemicals.
Prop 65 does not ban the sale of products containing these chemicals but instead requires warnings on any product, product packaging, or literature with
the product. Moreover , a Prop 65 warning does not mean that a product is in violation of any product safety standards or requirements. In fact, the
California government has claried that a Prop 65 warning “is not the same as a regulatory decision that a product is ‘safe’ or ‘unsafe.’” Many of these
chemicals have been used in everyday products for years without documented harm. For more information, go to https://oag.ca.gov/prop65/faqs-view-all .
A Prop 65 warning means that a company has either (1) evaluated the exposure and has concluded that it exceeds the “no signicant risk level”; or (2)
has chosen to provide a warning based on its understanding about the presence of a listed chemical without attempting to evaluate the exposure.
Does this law apply everywhere?
Prop 65 warnings are required under California law only . These warnings are seen throughout California in a wide range of settings, including but not
limited to restaurants, grocery stores, hotels, schools, and hospitals, and on a wide variety of products. Additionally , some online and mail order
retailers provide Prop 65 warnings on their websites or in catalogs.
How do the California warnings compare to federal limits?
Prop 65 standards are often more stringent than federal and international standards. There are various substances that require a Prop 65 warning
at levels that are far lower than federal action limits. For example, the Prop 65 standard for warnings for lead is 0.5 μg/day , which is well below
the federal and international standards.
Why don’t all similar products carry the warning?
Products sold in California require Prop 65 labelling while similar products sold elsewhere do not.
A company involved in a Prop 65 lawsuit reaching a settlement may be required to use Prop 65 warnings for its products, but other companies
making similar products may have no such requirement.
The enforcement of Prop 65 is inconsistent.
Companies may elect not to provide warnings because they conclude that they are not required to do so under Prop 65; a lack of warnings for a
product does not mean that the product is free of listed chemicals at similar levels.
Why does T oro include this warning?
T oro has chosen to provide consumers with as much information as possible so that they can make informed decisions about the products they buy and
use. T oro provides warnings in certain cases based on its knowledge of the presence of one or more listed chemicals without evaluating the level of
exposure, as not all the listed chemicals provide exposure limit requirements. While the exposure from T oro products may be negligible or well within the
“no signicant risk” range, out of an abundance of caution, T oro has elected to provide the Prop 65 warnings. Moreover , if T oro does not provide these
warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.
Rev A
Form No. 3460 - 488 Rev A
Soplador Axial Flex - Force Power
System
60V MAX
de modelo 51820 —Nº de serie 323000001 y superiores
de modelo 51820T —Nº de serie 323000001 y superiores
Registre su producto en www .T oro.com.
T raducción del original (ES)
*3460 - 488*
Si necesita ayuda, consulte
los vídeos instruccionales
en www .T oro.com/support
o llame al 1 - 888 - 384 - 9939
antes de devolver este
producto.
ADVERTENCIA
CALIFORNIA
Advertencia de la Propuesta 65
El cable eléctrico de este producto
contiene plomo, que el Estado de
California sabe que causa defectos
congénitos u otros peligros para la
reproducción. Lávese las manos después
de manejar el material.
El uso de este producto puede provocar la
exposición a sustancias químicas que el
Estado de California considera causantes
de cáncer , defectos congénitos u otros
trastornos del sistema reproductor .
Introducción
Este soplador está diseñado para ser usado por
usuarios domésticos para mover hojas y otros
residuos similares en espacios exteriores. Está
diseñada para usar baterías de ion litio de 60 V
de T oro. Estas baterías están diseñadas para ser
cargadas únicamente con cargadores de batería de
ion litio de 60 V de T oro. El uso de estos productos
para propósitos diferentes a los previstos puede ser
peligroso para usted y para otras personas.
El Modelo 51820T no incluye batería ni cargador .
Lea este manual detenidamente para aprender a
utilizar y mantener correctamente su producto, y
para evitar lesiones y daños al producto. Usted es
responsable de utilizar el producto de forma correcta
y segura.
V isite www .T oro.com para obtener más información,
incluidos consejos de seguridad, materiales de
formación, información sobre accesorios, ayuda
para encontrar a un distribuidor o para registrar su
producto.
Cuando necesite asistencia técnica, piezas genuinas
T oro o información adicional, póngase en contacto
con un Servicio Técnico Autorizado o con Atención
al cliente de T oro, y tenga a mano los números de
modelo y serie de su producto. Figura 1 identica la
ubicación de los números de modelo y serie en el
producto. Escriba los números en el espacio provisto.
Importante: Con su dispositivo móvil, puede
escanear el código QR (en su caso) de la place
del número de serie para acceder a información
sobre la garantía, las piezas, y otra información
sobre el producto.
g426535
Figura 1
1. Ubicación de los números de modelo y de serie.
Nº de modelo
Nº de serie
© 2022—The T oro® Company
81 1 1 L yndale A venue South
Bloomington, MN 55420
2
Póngase en contacto con nosotros en www .T oro.com.
Impreso en V ietnam
Reservados todos los derechos
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Toro Flex-Force Power System 60V MAX Axial Blower Manuel utilisateur

Catégorie
Souffleurs / sécheurs d'air
Taper
Manuel utilisateur