DeWalt DCS565P1 Manuel utilisateur

Marque: DeWalt

Modèle: DCS565P1

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

final page size: 8.5 x 5.5 in

If you have questions or comments, contactus.

Pour toute question ou tout commentaire, nouscontacter.

Si tiene dudas o comentarios,contáctenos.

1-800-4-

DeWALT

DCS565, DCS566

6-1/2" (165mm) 20V Max* Brushless Circular Saw

Scie circulaire sans balais 20V max* 165mm (6-1/2 po)

Sierra Circular sin Escobillas 20V Máx* de 165mm (6-1/2")

Instruction Manual

Guide D’utilisation

Manual de Instrucciones

English (original instructions) 5

Français (traduction de la notice d’instructions originale) 15

Español (traducido de las instrucciones originales) 27

Components

Trigger switch lock-off button

Trigger switch

Battery pack

Depth adjustment lever

Shoe

Lower blade guard

retractinglever

Lower blade guard

Blade clamping screw

Kerf indicator

Bevel adjustment lever

Worklight

Auxiliary handle

Battery release button

Blade wrench

Blade

Composants

Bouton de verrouillage de la gâchette

Gâchette

Bloc-piles

Levier d’ajustement de la profondeur

Patin

Levier de rétraction du protège-lame

inférieur

Protecteur inférieur de la lame

Vis de serrage de la lame

Indicateur de trait de scie

Levier de réglage du biseau

Lampe de travail

Poignée auxiliaire

Bouton de libération du bloc-piles

Clé pour lame

Lame

Componentes

Botón de bloqueo en apagado de

interruptor de gatillo

Interruptor de gatillo

Paquete de batería

Palanca de ajuste de profundidad

Zapata

Palanca retráctil de protección de

cuchilla inferior

Protección de cuchilla inferior

Tornillo de sujeción de cuchilla

Indicador de corte de sierra

Palanca de ajuste de bisel

Luz de trabajo

Manija auxiliar

Botón de liberación de batería

Llave de cuchilla

Cuchilla

Fig. A

DCS565

Fig.B Fig.C

Fig.D Fig.E

Fig.F

2012

Fig.G

75–100% charged

Chargé de 75 à 100 %

75–100% cargada

51–74% charged

Chargé de 51 à 74 %

51–74% cargada

< 50% charged

Chargé de < 50 %

< 50% cargada

Pack needs to be charged

Le bloc-piles doit être rechargé

La batería tiene que cargarse

Indicators/Témoin/Indicador

Charging

Bloc-piles en Cours

de Chargement

Unidad en Proceso de Carga

Fully Charged

Bloc-piles Chargé

Unidad Cargada

Hot/Cold Pack Delay

Suspension de Charge Contre

le Chaud/Froid

Restraso por Unidad Caliente/

Fría

Fig.H

Fig.I

Fig.J

Fig.K

Fig.L Fig.M

Fig.N Fig.O

Fig.P

Fig.Q

ENGLISH

Definitions: Safety Alert Symbols andWords

This instruction manual uses the following safety alert

symbols and words to alert you to hazardous situations and

your risk of personal injury or propertydamage.



DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

seriousinjury.



WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or

seriousinjury.



CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderateinjury.



(Used without word) Indicates a safety relatedmessage.

NOTICE: Indicates a practice not related to

personal injury which, if not avoided, may result in

propertydamage.

Intended Use

This heavy-duty circular saw is designed for professional

wood cutting applications. Do not cut metal, plastic,

concrete, masonry or fiber cementmaterials.

DO NOT use under wet conditions or in presence of

flammable liquids orgases.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

English (original instructions)



WARNING: Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

WARNING: To reduce the risk of injury, read the

instructionmanual.

GENERAL POWER TOOL SAFETY WARNINGS



WARNING: Read all safety warnings, instructions,

illustrations and specifications provided with

this power tool. Failure to follow all instructions

listed below may result in electric shock, fire and/or

seriousinjury.

SAVE ALL WARNINGS

AND INSTRUCTIONS FOR

FUTUREREFERENCE.

The term “power tool” in the warnings refers to your

mains‑operated (corded) power tool or battery‑operated

(cordless) powertool.

1) Work Area Safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create

sparks which may ignite the dust orfumes.

c ) Keep children and bystanders away while

operating a power tool. Distractions can cause you

to losecontrol.

2) Electrical Safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electricshock.

b ) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase

the risk of electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electricshock.

f ) If operating a power tool in a damp location

is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI

reduces the risk of electricshock.

3) Personal Safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personalinjury.

b ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as a dust

mask, non‑skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personalinjuries.

c ) Prevent unintentional starting. Ensure the switch

is in the off‑position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energizing power tools that have the switch

on invitesaccidents.

d ) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result

in personalinjury.

e ) Do not overreach. Keep proper footing and

balance at all times. This enables better control of the

power tool in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewelry. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewelry or long hair

can be caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of dust

collection can reduce dust‑relatedhazards.

ENGLISH

Safety Instructions for All Saws

CuttingProcedures

a ) DANGER: Keep hands away from cutting

area and the blade. Keep your second hand on

auxiliary handle, or motor housing. If both hands

are holding the saw, they cannot be cut by theblade.

b ) Do not reach underneath the workpiece. The

guard cannot protect you from the blade below

theworkpiece.

c ) Adjust the cutting depth to the thickness of the

workpiece. Less than a full tooth of the blade teeth

should be visible below theworkpiece.

d ) Never hold the workpiece in your hands or across

your leg while cutting. Secure the workpiece to a

stable platform. It is important to support the work

properly to minimize body exposure, blade binding, or

loss ofcontrol.

e ) Hold the power tool by insulated gripping

surfaces, when performing an operation where

the cutting tool may contact hidden wiring.

Contact with a "live" wire will also make exposed

metal parts of the power tool "live" and could give the

operator an electricshock.

f ) When ripping, always use a rip fence or straight

edge guide. This improves the accuracy of cut and

reduces the chance of bladebinding.

g ) Always use blades with correct size and shape

(diamond versus round) of arbor holes. Blades that

h ) Do not let familiarity gained from frequent use of

tools allow you to become complacent and ignore

tool safety principles. A careless action can cause

severe injury within a fraction of asecond.

4) Power Tool Use and Care

a ) Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which it

wasdesigned.

b ) Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must

berepaired.

c ) Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting

the power toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands of

untrainedusers.

e ) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tool’s operation. If

damaged, have the power tool repaired before

use. Many accidents are caused by poorly maintained

powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking

into account the working conditions and the

work to be performed. Use of the power tool for

operations different from those intended could result in

a hazardoussituation.

h ) Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpectedsituations.

5) Battery Tool Use and Care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with

another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury andfire.

c ) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects,

that can make a connection from one terminal to

another. Shorting the battery terminals together may

cause burns or afire.

d ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation

orburns.

e ) Do not use a battery pack or tool that is damaged

or modified. Damaged or modified batteries may

exhibit unpredictable behavior resulting in fire,

explosion or risk ofinjury.

f ) Do not expose a battery pack or tool to

fire or excessive temperature. Exposure to

fire or temperature above 265°F (130°C) may

causeexplosion.

g ) Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specified in the instructions.

Charging improperly or at temperatures outside the

specified range may damage the battery and increase

the risk offire.

6) Service

a ) Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power tool

ismaintained.

b ) Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized serviceproviders.

ENGLISH

Additional Safety Information



WARNING: Never modify the power tool or any part of

it. Damage or personal injury couldresult.



WARNING: ALWAYS use safety glasses. Everyday

eyeglasses are NOT safety glasses. Also use face or

dust mask if cutting operation is dusty. ALWAYS WEAR

CERTIFIED SAFETYEQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratoryprotection.



WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to the State

of California to cause cancer, birth defects or

other reproductive harm. Some examples of these

chemicalsare:

• lead from lead‑based paints,

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from

chemically‑treatedlumber.

Your risk from these exposures varies, depending on

how often you do this type of work. To reduce your

exposure to these chemicals: work in a well ventilated

area, and work with approved safety equipment, such

as those dust masks that are specially designed to filter

out microscopicparticles.

The protruding blade may cut objects that can

causekickback.

Lower Guard Function Safety

Instructions

a ) Check the lower guard for proper closing before

each use. Do not operate the saw if lower guard

does not move freely and close instantly. Never

clamp or tie the lower guard into the open

position. If saw is accidentally dropped, lower guard

may be bent. Raise the lower guard with the retracting

handle and make sure it moves freely and does not

touch the blade or any other part, in all angles and

depths ofcut.

b ) Check the operation of the lower guard spring.

If the guard and the spring are not operating

properly, they must be serviced before use. Lower

guard may operate sluggishly due to damaged parts,

gummy deposits, or a build‑up ofdebris.

c ) The low guard may be retracted manually only for

special cuts such as “plunge cuts” and “compound

cuts.” Raise the lower guard by retracting the

handle and as soon as blade enters the material,

the lower guard must be released. For all other

sawing, the lower guard should operateautomatically.

d ) Always observe that the lower guard is covering

the blade before placing saw down on bench or

floor. An unprotected, coasting blade will cause the

saw to walk backwards, cutting whatever is in its path.

Be aware of the time it takes for the blade to stop after

switch isreleased.

Further Safety Instructions for All Saws

Causes and Operator Prevention

ofKickback:

• Kickback is a sudden reaction to a pinched, bound or

misaligned saw blade, causing an uncontrolled saw to lift

up and out of the workpiece toward the operator;

• When the blade is pinched or bound tightly by the kerf

closing down, the blade stalls and the motor reaction drives

the unit rapidly back toward the operator;

• If the blade becomes twisted or misaligned in the cut, the

teeth at the back edge of the blade can dig into the top

surface of the wood causing the blade to climb out of the

kerf and jump back toward theoperator.

Kickback is the result of saw misuse and/or incorrect operating

procedures or conditions and can be avoided by taking proper

precautions as given below:

a ) Maintain a firm grip with both hands on the saw

and position your arms to resist kickback forces.

Position your body to either side of the blade,

but not in line with the blade. Kickback could cause

the saw to jump backwards, but kickback forces can

be controlled by the operator, if proper precautions

aretaken.

b ) When blade is binding, or when interrupting a

cut for any reason, release the trigger and hold

the saw motionless in the material until the

blade comes to a complete stop. Never attempt

to remove the saw from the work or pull the saw

backward while the blade is in motion or kickback

may occur. Investigate and take corrective actions to

eliminate the cause of bladebinding.

c ) When restarting a saw in the workpiece, center

the saw blade in the kerf and check that saw teeth

are not engaged into the material. If a saw blade

binds, it may walk up or kickback from the workpiece

as the saw isrestarted.

d ) Support large panels to minimize the risk of blade

pinching and kickback. Large panels tend to sag

under their own weight. Supports must be placed

under the panel on both sides, near the line of cut and

near the edge of thepanel.

e ) Do not use dull or damaged blades. Unsharpened

or improperly set blades produce narrow kerf causing

excessive friction, blade binding andkickback.

f ) Blade depth and bevel adjusting locking levers

must be tight and secure before making the cut.

If blade adjustment shifts while cutting, it may cause

binding andkickback.

g ) Use extra caution when making a “plunge

cut” into existing walls or other blind areas.

do not match the mounting hardware of the saw will

run off‑center, causing loss ofcontrol.

h ) Never use damaged or incorrect blade washers

or bolt. The blade washers and bolt were specially

designed for your saw, for optimum performance and

safety ofoperation.

ENGLISH

liquids, gases or dust. Inserting or removing the battery

pack from the charger may ignite the dust orfumes.

• NEVER force the battery pack into the charger. DO

NOT modify the battery pack in any way to fit into a

non‑compatible charger as battery pack may rupture

causing serious personal injury. Consult the chart

at the end of this manual for compatibility of batteries

andchargers.

• Charge the battery packs only in

DeWALT

chargers.

• DO NOT splash or immerse in water or otherliquids.

• DO NOT allow water or any liquid to enter batterypack.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or

exceed 104°F (40°C) (such as outside sheds or metal

buildings in summer). For best life store battery packs in

a cool, drylocation.

NOTE: Do not store the battery packs in a tool with

the trigger switch locked on. Never tape the trigger

switch in the ONposition.

• Do not incinerate the battery pack even if it is

severely damaged or is completely worn out. The

battery pack can explode in a fire. Toxic fumes and

materials are created when lithium‑ion battery packs

areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open

eye for 15minutes or until irritation ceases. If medical

attention is needed, the battery electrolyte is composed of a

mixture of liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause

respiratory irritation. Provide fresh air. If symptoms

persist, seek medicalattention.

• Battery liquid may be flammable if exposed to spark

orflame.

• Never attempt to open the battery pack for any

reason. If the battery pack case is cracked or

damaged, do not insert into the charger. Do not crush,

drop or damage the battery pack. Do not use a battery

pack or charger that has received a sharp blow, been

dropped, run over or damaged in any way (e.g., pierced

with a nail, hit with a hammer, stepped on). Damaged

battery packs should be returned to the service center

forrecycling.

Storage Recommendations

The best storage place is one that is cool and dry, away

from direct sunlight and excess heat or cold. Store the fully

charged battery pack out of thecharger.

Battery Pack Cleaning Instructions

Dirt and grease may be removed from the exterior of the

battery pack using a cloth or soft non-metallic brush. Do not

use water or any cleaningsolutions.

Fuel Gauge Battery Packs (Fig.B)

Some battery packs include a fuel gauge. When the

fuel gauge button is pressed and held, the LED lights

READ ALL INSTRUCTIONS

Important Safety Instructions for All

Battery Packs



WARNING: Read all safety warnings, instructions,

and cautionary markings for the battery pack,

charger and product. Failure to follow the

warnings and instructions may result in electric

shock, fire and/or seriousinjury.

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable

BATTERIES AND CHARGERS

The battery pack is not fully charged out of the carton.

Before using the battery pack and charger, read the

safety instructions below and then follow charging

proceduresoutlined. When ordering replacement battery

packs, be sure to include the catalog number andvoltage.

The label on your tool may include the following symbols. The

symbols and their definitions are asfollows:

BPM .................... beats per minute

V ......................... volts

min ..................... minutes

or DC ............direct current

…/min ..............per minute

RPM .................... revolutions per

minute

A ......................... amperes

Hz .......................hertz

W ........................watts

Wh ......................watt hours

.......................no load speed

n .........................rated speed

.....................safety alert symbol

..................... wear respiratory

protection

..................... wear eye protection

..................... Class II Construction

(double insulated)

..................... wear hearing

protection

..................... read all

documentation

..................... avoid staring at

light

or AC............alternating current

Ah ....................... amp hours

• Wear protective clothing and wash exposed areas

with soap and water. Allowing dust to get into your

mouth, eyes, or lay on the skin may promote absorption

of harmfulchemicals. Direct particles away from face

andbody.

• Use the appropriate dust extractor vacuum to remove

the vast majority of static and airborne dust. Failure

to remove static and airborne dust could contaminate the

working environment or pose an increased health risk to

the operator and those in closeproximity.

• Use clamps or other practical ways to secure and

support the workpiece to a stable platform. Holding

the work by hand or against your body is unstable and may

lead to loss ofcontrol andinjury.

• Air vents often cover moving parts and should be

avoided. Loose clothes, jewelry or long hair can be caught

in movingparts.



CAUTION: When not in use, place tool on its

side on a stable surface where it will not cause

a tripping or falling hazard. Some tools with large

battery packs will stand upright on the battery pack

but may be easily knockedover.

ENGLISH

• DO NOT attempt to charge the battery pack with

any chargers other than a

DeWALT

charger.

DeWALT

chargers and battery packs are specifically designed to

worktogether.

• These chargers are not intended for any uses other

than charging

DeWALT

rechargeable battery packs.

Charging other types of battery packs may cause them to

overheat and burst, resulting in personal injury, property

damage, fire, electric shock orelectrocution.

• Do not expose the charger to rain orsnow.

• Do not allow water or any liquid to entercharger.

• Pull by the plug rather than the cord when

disconnecting the charger. This will reduce the risk of

damage to the electric plug andcord.

• Make sure that the cord is located so that it will not

be stepped on, tripped over or otherwise subjected to

damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in

risk of fire, electric shock orelectrocution.

• When operating a charger outdoors, always provide

a dry location and use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electricshock.

• An extension cord must have adequate wire size

(AWG or American Wire Gauge) for safety. The smaller

the gauge number of the wire, the heavier the cord and

thus the greater its capacity. An undersized cord will

cause a drop in line voltage resulting in loss of power and

overheating. The following table shows the correct size

to use depending on total length of all extension cords

plugged together, and nameplate ampere rating. If in

doubt, use the next heaviergauge.

Minimum Gauge for Cord Sets

Volts

Total Length of Cord in Feet

(meters)

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

Ampere Rating

American Wire Gauge

More Than Not More

Than

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or place

the charger on a soft surface that might block the

ventilation slots and result in excessive internal heat.

Place the charger in a position away from any heat source.

The charger is ventilated through slots in the top and the

bottom of thehousing.

• Do not operate the charger with a damaged cord

orplug. Have them replacedimmediately.

• Do not operate the charger if it has received a sharp

blow, been dropped or otherwise damaged in any

way. Take it to an authorized servicecenter.

• Do not disassemble the charger; take it to an

authorized service center when service or repair

Important Safety Instructions for All

Battery Chargers



WARNING: Read all safety warnings, instructions,

and cautionary markings for the battery pack,

charger and product. Failure to follow the

warnings and instructions may result in electric

shock, fire and/or seriousinjury.

The RBRC® Seal

Please take your spent battery packs to

an authorized

DeWALT

service center or

to your local retailer for recycling. In some

areas, it is illegal to place spent battery

packs in the trash. You may also contact your local recycling

center for information on where to drop off the spent

battery pack. Do not place in curbside recycling. For more

information visit www.call2recycle.org. or call the toll free

number in the RBRC®Seal.

RBRC® is a registered trademark of Call 2Recycle,Inc.

Shipping the

DeWALT

FLEXVOLT™ Battery Pack

The

DeWALT

FLEXVOLT™ battery pack has a battery cap that

should be used when shipping the batterypack.

Attach the cap to the battery pack to ready it for shipping.

This converts the battery pack to three separate 20V

batteries. The three batteries have the Watt hour rating

labeled “Shipping” on the battery pack. If shipping without

the cap or in a tool, the pack is one battery at the Watt hour

rating labeled“Use”.

Example battery pack label:

USE: 120 Wh SHIPPING: 3 x 40 Wh

In this example, the battery pack is three batteries with 40

Watt hours each when using the cap. Otherwise, the battery

pack is one battery with 120 Watthours.

will indicate the approximate level of charge remaining.

This does not indicate tool functionality and is subject to

variation based on product components, temperature, and

end-userapplication.

Transportation



WARNING: Fire hazard. Do not store, carry, or

transport the battery pack so that metal objects

can contact exposed battery terminals. For

example, do not place the battery pack in aprons,

pockets, tool boxes, product kit boxes, drawers, etc.,

with loose nails, screws, keys, coins, hand tools, etc.

When transporting individual battery packs, make

sure that the battery terminals are protected and well

insulated from materials that could contact them and

cause a short circuit. NOTE: Li‑ion battery packs should

not be put in checked baggage on airplanes and must

be properly protected from short circuits if they are in

carry‑onbaggage.

ENGLISH

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start‑up can causeinjury.

Wall Mounting

Some

DeWALT

chargers are designed to be wall mountable

or to sit upright on a table or work surface. If wall mounting,

locate the charger within reach of an electrical outlet, and

away from a corner or other obstructions which may impede

air flow. Use the back of the charger as a template for the

location of the mounting screws on the wall. Mount the

charger securely using drywall screws (purchased separately)

at least 1” (25.4mm) long, with a screw head diameter of

0.28–0.35” (7–9mm), screwed into wood to an optimal

depth leaving approximately 7/32” (5.5 mm) of the screw

exposed. Align the slots on the back of the charger with the

exposed screws and fully engage them in theslots.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

does not indicate a problem. To facilitate the cooling of

the battery pack after use, avoid placing the charger or

battery pack in a warm environment such as in a metal

shed or an uninsulatedtrailer.

2. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp

or other appliance;

b. Check to see if receptacle is connected to a light

switch which turns power off when you turn out

the lights;

c. If charging problems persist, take the tool, battery

pack and charger to your local servicecenter.

3. You may charge a partially used pack whenever you

desire with no adverse effect on the batterypack.

Charger Cleaning Instructions



WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using

a cloth or soft non‑metallic brush. Do not use water or

any cleaningsolutions.

is required. Incorrect reassembly may result in a risk of

electric shock, electrocution orfire.

• The charger is designed to operate on standard

120V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.

• Foreign materials of a conductive nature, such as, but

not limited to, grinding dust, metal chips, steel wool,

aluminum foil or any buildup of metallic particles

should be kept away from the charger cavities and

ventilation slots.

• Always unplug the charger from the power supply

when there is no battery pack in thecavity.

Charging a Battery (Fig.C)

1. Plug the charger into an appropriate outlet.

2. Insert and fully seat battery pack. Red charging light will

continuously blink whilecharging.

3. Charging is complete when the red charging light

remains continuously ON. Battery pack can be left in

charger or removed. Some chargers require the battery

pack release button to be pressed forremoval.

4. Charger will not charge a faulty battery pack, which

may be indicated by the light staying OFF. Take charger

and battery pack to an authorized service center if light

staysOFF.

NOTE: Refer to label near charging light on charger

for blink patterns. Older chargers may have additional

information and/or may not have a yellow indicatorlight.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot

or too cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery pack has reached an

appropriate temperature. The charger then automatically

switches to the pack charging mode. This feature ensures

maximum battery packlife.

A cold battery pack may charge at a slower rate than a warm

batterypack.

The hot/cold pack delay will be indicated by the red light

continuing to blink but with the yellow light continuously

ON. Once the battery pack has reached an appropriate

temperature, the yellow light will turn OFF and the charger

will resume the chargingprocedure.

DCB118 and DCB1112 Chargers

The DCB118 and DCB1112 chargers are equipped with

an internal fan designed to cool the battery pack. The fan

will turn on automatically when the battery pack needs to

becooled.

Electronic Protection System

Li-Ion tools are designed with an Electronic Protection

System that will protect the battery pack against overloading,

overheating or deep discharge. The tool will automatically

turn off and the battery pack will need to berecharged.

Important Charging Notes

1. The charger and battery pack may become warm to the

touch while charging. This is a normal condition, and

MAXIMUM CUTTING DEPTH

90° 2-1/8" (54 mm)

45° 1-5/8" (41,3 mm)

Changing Blades

To Install the Blade (Fig.A, D, E)



WARNING: Remove battery before service,

adjustment, installing or removingaccessories.

1. Place inner clamp washer

17

on saw spindle

16

with

the large flat surface facing out toward theblade.

2. Retract the lower blade guard

7

and place blade on saw

spindle against the inner clamp washer, making sure

that the blade will rotate in the proper direction (the

ENGLISH

Kickback

Kickback is a sudden reaction to a pinched, bound or

misaligned saw blade, causing an uncontrolled saw to lift

up and out of the workpiece toward the operator. When the

blade is pinched or bound tightly by the kerf closing down,

the blade stalls and the motor reaction drives the unit rapidly

back toward the operator. If the blade becomes twisted or

misaligned in the cut, the teeth at the back edge of the blade

can dig into the top surface of the wood causing the blade to

climb out of the kerf and jump back toward theoperator.

Blades



WARNING: To minimize the risk of eye injury, always

use eye protection. Carbide is a hard but brittle

material. Foreign objects in the workpiece such as wire

or nails can cause tips to crack or break. Only operate

saw when proper saw blade guard is in place. Mount

blade securely in proper rotation before using, and

always use a clean, sharpblade.



WARNING: Do not cut metal, plastic, concrete,

masonry or fiber cement materials with thissaw.

Do not use abrasive wheels or blades. A dull blade will cause

slow inefficient cutting, overload on the saw motor, excessive

splintering, and could increase the possibility of kickback.

Please refer to the table below to determine the correct size

replacement blade for your modelsaw.

Blade Diameter Teeth Application

6–1/2" (165 mm) 18 General purpose cutting

6–1/2" (165 mm) 24 Smooth woodcutting

6–1/2" (165 mm) 90 Non-carbide, plywood/ vinyl siding cutting

lower blade guard to protect you under all

circumstances. Your safety depends on following

all warnings and precautions as well as proper

operation of the saw. Check lower blade guard

for proper closing before each use as outlined

in Further Safety Instructions for All Saws.

If the lower blade guard is missing or not

working properly, have the saw serviced before

using. To assure product safety and reliability,

repair, maintenance and adjustment should be

performed by an authorized service center or

other qualified service organization, always using

identical replacementparts.

Checking the Lower Guard(Fig.A)

1. Turn tool off and disconnect from powersupply.

2. Rotate the lower blade guard retracting lever

6

from the

fully closed position to the fully openposition.

3. Release the lever and observe the guard

7

return to the

fully closedposition.

The tool should be serviced by a qualified service center if it:

• fails to return to the fully closed position,

• moves intermittently or slowly, or

• contacts the blade or any part of the tool in all angles

and depth ofcut.

Lower Blade Guard



WARNING: The lower blade guard is a safety

feature which reduces the risk of serious personal

injury. Never use the saw if the lower blade

guard is missing, damaged, misassembled

or not working properly. Do not rely on the

direction of the rotation arrow on the saw blade and the

teeth must point in the same direction as the direction of

rotation arrow on the lower blade guard). Do not assume

that the printing on the blade will always be facing

you when properly installed. When retracting the lower

blade guard to install the blade, check the condition

and operation of the lower blade guard to assure that

it is working properly. Make sure it moves freely and

does not touch the blade or any other part, in all angles

and depths of cut.

3. Place outer clamp washer

18

on saw spindle with the

large flat surface against the blade with beveled side

facingout.

4. Thread blade clamping screw

8

into saw spindle by

hand (screw has left-hand threads and must be turned

counterclockwise totighten).

5. Depress the blade lock button

19

while turning the saw

spindle with the blade wrench

14

until the blade lock

engages and the blade stopsrotating.

6. Tighten the blade clamping screw firmly with the

bladewrench.

NOTE: Never engage the blade lock while saw is running, or

engage in an effort to stop the tool. Never turn the saw on

while the blade lock is engaged. Serious damage to your saw

willresult.

To Replace the Blade (Fig.A, D, E)



WARNING: Remove battery before service, adjustment,

installing or removingaccessories.

1. To loosen the blade clamping screw

8

, depress the

blade lock button

19

and turn the saw spindle with

the blade wrench

14

until the blade lock engages and

the blade stops rotating. With the blade lock engaged,

turn the blade clamping screw clockwise with the blade

wrench (screw has left-hand threads and must be turned

clockwise toloosen).

2. Remove the blade clamping screw

8

and outer clamp

washer

18

only. Remove oldblade.

3. Clean any sawdust that may have accumulated in the

guard or clamp washer area and check the condition

and operation of the lower blade guard as previously

outlined. Do not lubricate thisarea.

4. Select the proper blade for the application (see Blades).

Always use blades that are the correct size (diameter)

with the proper size and shape center hole for mounting

on the saw spindle. Always assure that the maximum

recommended speed (rpm) on the saw blade meets or

exceeds the speed (rpm) of thesaw.

5. Follow steps 2 through 6 under To Install the

Blade, making sure that the blade will rotate in the

properdirection.

ENGLISH

Mounting the Dust Extraction

Port(Fig.A,H, I)

Your circular saw is supplied with a dust extractionport.

To Install the Dust Extraction Port

1. Fully loosen depth adjustment lever

4

2. Place the shoe

5

in the lowestposition.

Kerf Indicator (Fig.A)

The front of the saw shoe has a kerf indicator

9

for vertical

and bevel cutting. This indicator enables you to guide the

saw along cutting lines penciled on the material being cut.

The kerf indicator lines up with the left (inner) side of the

saw blade, which makes the slot or “kerf” cut by the moving

blade fall to the right of the indicator. Guide along the

penciled cutting line so that the kerf falls into the waste or

surplusmaterial.

Bevel Angle Adjustment (Fig.A, L)

The full range of the bevel adjustment is from 0° to 50°. The

quadrant is graduated in increments of 1°. On the front of the

saw is a bevel angle adjustment mechanism consisting of a

calibrated quadrant and a bevel adjustment lever

10

To Set the Saw for a Bevel Cut

1. Loosen (counterclockwise) the bevel adjustment

lever

10

and tilt shoe (

5

, Fig.A) to the desired angle by

aligning the pointer with the desired anglemark.

2. Retighten lever firmly (clockwise).

Cutting Depth Adjustment (Fig.A, K)

1. Hold the saw firmly and loosen (clockwise) the depth

adjustment lever

4

and move shoe (

5

, Fig.A) to obtain

the desired depth ofcut.

2. Make sure the depth adjustment lever has been

retightened (counterclockwise) before operatingsaw.

For the most efficient cutting action, set the depth

adjustment so that one-half tooth of the blade will project

below the material to be cut. This distance is from the tip of

the tooth to the bottom of the gullet in front of it. This keeps

blade friction at a minimum, removes sawdust from the cut,

results in cooler, faster sawing and reduces the chance of

kickback. A method for checking for correct cutting depth

is shown in FigureK. Lay a piece of the material you plan to

cut along the side of the blade, as shown, and observe how

much tooth projects beyond thematerial.

7. RESTARTING A CUT WITH THE BLADE TEETH

JAMMED AGAINST THE MATERIAL

a. The saw should be brought up to full operating speed

before starting a cut or restarting a cut after the unit

has been stopped with the blade in the kerf. Failure to

do so can cause stalling andkickback.

Any other conditions which could result in pinching, binding,

twisting, or misalignment of the blade could cause kickback.

Refer to the sections Further Safety Instructions for All

Saws and Blades for procedures and techniques that will

minimize the occurrence ofkickback.

Kickback is more likely to occur when any of the following

conditionsexists.

1. IMPROPER WORKPIECE SUPPORT

a. Sagging or improper lifting of the cut off piece can

cause pinching of the blade and lead tokickback.

b. Cutting through material supported at the outer ends

only can cause kickback. As the material weakens it

sags, closing down the kerf and pinching theblade.

c. Cutting off a cantilevered or overhanging piece of

material from the bottom up in a vertical direction

can cause kickback. The falling cut off piece can pinch

theblade.

d. Cutting off long narrow strips (as in ripping) can cause

kickback. The cut off strip can sag or twist closing the

kerf and pinching theblade.

e. Snagging the lower guard on a surface below the

material being cut momentarily reduces operator

control. The saw can lift partially out of the cut

increasing the chance of bladetwist.

2. IMPROPER DEPTH OF CUT SETTING ON SAW

a. To make the most efficient cut, the blade should

protrude only far enough to expose one-half of a

tooth. This allows the shoe to support the blade and

minimizes twisting and pinching in the material. See

the section titled Cutting DepthAdjustment.

3. BLADE TWISTING MISALIGNMENT IN CUT

a. Pushing harder to cut through a knot, a nail or a hard

grain area can cause the blade totwist.

b. Trying to turn the saw in the cut (trying to get back on

the marked line) can cause bladetwist.

c. Overreaching or operating the saw with poor body

control (out of balance), can result in twisting

theblade.

d. Changing hand grip or body position while cutting

can result in bladetwist.

e. Backing up the saw to clear blade can lead totwist.

4. MATERIALS THAT REQUIRE EXTRA ATTENTION

a. Wet lumber

b. Green lumber (material freshly cut or not kiln dried)

c. Pressure treated lumber (material treated with

preservatives or anti-rot chemicals)

5. USE OF DULL OR DIRTY BLADES

a. Dull blades cause increased loading of the saw. To

compensate, an operator will usually push harder

which further loads the unit and promotes twisting

of the blade in the kerf. Worn blades may also have

insufficient body clearance which increases the

chance of binding and increasedloading.

6. LIFTING THE SAW WHEN MAKING A BEVEL CUT

a. Bevel cuts require special operator attention to proper

cutting techniques – especially guidance of the

saw. Both blade angle to the shoe and greater blade

surface in the material increase the chance for binding

and misalignment (twist) tooccur.

ENGLISH

Cutting (Fig. N, O)

Place the wider portion of the saw shoe on that part of the

workpiece which is solidly supported, not on the section

that will fall off when the cut is made. As an example,

FigureN illustrates the RIGHT way to cut off the end of a

board. Always clamp work. Don’t try to hold short pieces

by hand! (FigureO) Remember to support cantilevered and

overhanging material. Use caution when sawing material

frombelow.

Be sure saw is up to full speed before blade contacts material

to be cut. Starting saw with blade against material to be

cut or pushed forward into kerf can result in kickback. Push

the saw forward at a speed which allows the blade to cut

withoutlaboring.

Hardness and toughness can vary even in the same piece of

material, and knotty or damp sections can put a heavy load

on the saw. When this happens, push the saw more slowly,

but hard enough to keep working without much decrease

in speed. Forcing the saw can cause rough cuts, inaccuracy,

kickback, and over-heating of themotor.

Should your cut begin to go off the line, don’t try to force

it back on. Release the trigger switch and allow blade to

come to a complete stop. Then you can withdraw the saw,

sight anew, and start a new cut slightly inside the wrong

one. Withdraw the saw if you must shift the cut. Forcing

a correction inside the cut can stall the saw and lead

tokickback.

IF SAW STALLS, RELEASE THE TRIGGER SWITCH AND BACK THE

SAW UNTIL IT IS LOOSE. BE SURE BLADE IS STRAIGHT IN THE

CUT AND CLEAR OF THE CUTTING EDGE BEFORERESTARTING.

As you finish a cut, release the trigger switch and allow the

blade to stop before lifting the saw from the work. As you

lift the saw, the spring-tensioned lower blade guard will

automatically close under the blade. Remember the blade

is exposed until this occurs. Never reach under the work for

any reason. When you have to retract the lower blade guard

manually (as is necessary for starting pocket cuts), always use

the retractinglever.



WARNING: When cutting thin strips, be careful to

ensure that small cutoff pieces don’t hang up on the

inside of the lower bladeguard.

Workpiece Support (Fig.G, M)



WARNING: It is important to support the work

properly and to hold the saw firmly to prevent loss of

control which could cause personal injury. FigureG

illustrates proper hand support of the saw. Maintain a

firm grip with both hands on the saw and position your

body and arm to allow you to resist kickback if it occurs.

ALWAYS TURN OFF TOOL AND REMOVE BATTERY

BEFORE MAKING ANY ADJUSTMENTS!

Figure G shows proper sawing position. Note that hands are

kept away from cutting area. To avoid kickback, DO support

board or panel NEAR the cut (Fig.M). DON’T support board

or panel away from the cut (Fig.M).

Place the work with its “good” side – the one on which

appearance is most important – down. The saw cuts upward,

so any splintering will be on the work face that is up when

you cutit.

Rafter Hook (Fig.J [DCS565])



WARNING: To reduce the risk of serious personal injury,

do not use the tool's rafter hook to hang the tool from

your body. DO NOT use the rafter hook for tethering or

securing the tool to a person or object during use. DO

NOT suspend tool overhead or suspend objects from

the rafterhook.



WARNING: To reduce the risk of injury from the circular

saw falling on operators or bystanders, make sure it

is supported securely when using the rafter hook, or

resting in a secure and stable location when not in

use. Be sure to keep the area below clear to reduce the

risk of the tool or off‑cut material falling and striking

someone or somethingbelow.

The circular saw has a convenient rafter hook

23

that allows

it to hang on a suitable, stable structure between uses.

The rafter hook is not for tethering or securing the tool to a

person or object during use whenelevated.

Proper Hand Position (Fig. G)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position as shown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Proper hand position requires one hand on the main

handle 

20

and one hand on the auxilliary handle

12

Installing and Removing the Battery Pack

(Fig.F)

NOTE: For best results, make sure your battery pack is

fullycharged.

To install the battery pack

3

into the tool handle, align the

battery pack with the rails inside the tool’s handle and slide it

into the handle until the battery pack is firmly seated in the

tool and ensure that it does notdisengage.

To remove the battery pack from the tool, press the release

button

13

and firmly pull the battery pack out of the tool

handle. Insert it into the charger as described in the charger

section of thismanual.

OPERATION



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start‑up can causeinjury.

Prior to Operation

• Make sure the guards have been mounted correctly.The

saw blade guard must be in closedposition.

• Make sure the saw blade rotates in the direction of the

arrow on theblade.

• Do not use excessively worn sawblades.

3. Push the dust extraction port

22

onto the circular saw

body until the locks engage the dust extraction port and

an audible click isheard.

ENGLISH

Thank you for your purchase. Register your product nowfor:

• WARRANTY SERVICE: Registering your product will

help you obtain more efficient warranty service in case

there is a problem with yourproduct.

• CONFIRMATION OF OWNERSHIP: In case of

an insurance loss, such as fire, flood or theft, your

registration of ownership will serve as your proof

ofpurchase.

• FOR YOUR SAFETY: Registering your product will

allow us to contact you in the unlikely event a safety

notification is required under the Federal Consumer

SafetyAct.

• Register online at www.dewalt.com

Repairs

The charger and battery pack are notserviceable. There are

no serviceable parts inside the charger or batterypack.



WARNING: To assure product SAFETY and RELIABILITY,

repairs, maintenance and adjustment (including brush

inspection and replacement, when applicable) should

be performed by a

DeWALT

factory service center or a

DeWALT

authorized service center. Always use identical

replacementparts.

Accessories



WARNING: Since accessories, other than those offered

DeWALT

, have not been tested with this product, use

of such accessories with this tool could be hazardous.

To reduce the risk of injury, only

DeWALT

recommended

accessories should be used with thisproduct.

Recommended accessories for use with your tool are available

at extra cost from your local dealer or authorized service

center. If you need assistance in locating any accessory, please

contact

DeWALT

call 1-800-4-

DeWALT

(1-800-433-9258) or

visit our website: www.dewalt.com.



WARNING: Never use solvents or other harsh

chemicals for cleaning the non‑metallic parts of the

tool. These chemicals may weaken the plastic materials

used in these parts. Use a cloth dampened only with

water and mild soap. Never let any liquid get inside the

tool; never immerse any part of the tool into aliquid.

Cleaning



WARNING: Blow dirt and dust out of all air vents with

clean, dry air at least once a week. To minimize the risk

of eye injury, always wear ANSI Z87.1approved eye

protection when performingthisprocedure.

MAINTENANCE



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start‑up can causeinjury.

Worklight (Fig.A [DCS565])



CAUTION: Do not stare into worklight. Serious eye

injury couldresult.

The worklight

11

is activated when the trigger switch is

depressed, and will automatically turn off 20 seconds after

the trigger switch is released. If the trigger switch remains

depressed, the worklight will remainon.

NOTE: The worklight is for lighting the immediate work

surface and is not intended to be used as aflashlight.

Pocket Cutting (Fig.Q)



WARNING: Never tie the lower blade guard in a raised

position. Never move the saw backwards when pocket

cutting. This may cause the saw to raise up off the work

surface, which could causeinjury.

A pocket cut is one that is made in a floor, wall or other

flatsurface.

1. Adjust the saw shoe so the blade cuts at desireddepth.

2. Tilt the saw forward and rest front of the shoe on material

to becut.

3. Using the lower blade guard retracting lever, retract the

lower blade guard to an upward position. Lower the

rear of the shoe until the blade teeth almost touch the

cuttingline.

4. Release the lower blade guard (its contact with the work

will keep it in position to open freely as you start the cut).

Remove your hand from the lower blade guard retracting

lever and firmly grip the auxiliary handle

12

, as shown

in FigureQ. Position your body and arm to allow you to

resist kickback if itoccurs.

5. Make sure blade is not in contact with cutting surface

before startingsaw.

6. Start the motor and gradually lower the saw until its shoe

rests flat on the material to be cut. Advance saw along

the cutting line until cut iscompleted.

7. Release the trigger switch and allow the blade to

stop completely before withdrawing the blade from

thematerial.

8. When starting each new cut, repeat the abovesteps.

Ripping (Fig.P)

Ripping is the process of cutting wider boards into narrower

strips – cutting grain lengthwise. Hand guiding is more

difficult for this type of sawing and the use of a

DeWALT

rip

fence isrecommended.

Three Year Limited Warranty

For warranty terms, go to https://www.dewalt.com/Legal/

Warranty/3-Year-Limited-Warranty.

To request a written copy of the warranty terms, contact:

Customer Service at D

WALT Industrial Tool Co., 701East

Joppa Road, Towson, MD 21286 or call 1-800-4-

DeWALT

(1-800-433-9258).

FRANÇAIS

1) Sécurité du lieu de travail

a ) Tenir l’aire de travail propre et bien éclairée.

Les lieux encombrés ou sombres sont propices

auxaccidents.

b ) Ne pas faire fonctionner d’outils électriques

dans un milieu déflagrant, tel qu’en présence de

liquides, de gaz ou de poussières inflammables.

Les outils électriques produisent des étincelles qui

pourraient enflammer la poussière ou lesvapeurs.

c ) Éloigner les enfants et les personnes à proximité

pendant l’utilisation d’un outil électrique. Une

distraction pourrait en faire perdre la maîtrise

àl’utilisateur.

2) Sécurité en matière d’électricité

a ) Les fiches des outils électriques doivent

correspondre à la prise. Ne jamais modifier la

fiche d’aucune façon. Ne jamais utiliser de fiche

d’adaptation avec un outil électrique mis à la

terre. Le risque de choc électrique sera réduit par

l’utilisation de fiches non modifiées correspondant à

laprise.

b ) Éviter tout contact physique avec des surfaces

mises à la terre comme des tuyaux, des radiateurs,

des cuisinières et des réfrigérateurs. Le risque de

choc électrique est plus élevé si votre corps est mis à

laterre.

c ) Ne pas exposer les outils électriques à la pluie ou

à l’humidité. La pénétration de l’eau dans un outil

électrique augmente le risque de chocélectrique.

d ) Ne pas utiliser le cordon de façon abusive. Ne

jamais utiliser le cordon pour transporter, tirer

ou débrancher un outil électrique. Tenir le

cordon éloigné de la chaleur, de l’huile, des bords

tranchants et des pièces mobiles. Les cordons

endommagés ou enchevêtrés augmentent les risques

de chocélectrique.

e ) Pour l’utilisation d’un outil électrique à l’extérieur,

se servir d’une rallonge convenant à cette

application. L’utilisation d’une rallonge conçue pour

l’extérieur réduira les risques de chocélectrique.

f ) S’il est impossible d’éviter l’utilisation d’un

outil électrique dans un endroit humide,

brancher l’outil dans une prise ou sur un circuit

d’alimentation dotés d’un disjoncteur de fuite à

la terre (GFCI). L’utilisation de ce type de disjoncteur

réduit les risques de chocélectrique.

3) Sécurité personnelle

a ) Être vigilant, surveiller le travail effectué et faire

preuve de jugement lorsqu’un outil électrique est

utilisé. Ne pas utiliser d’outil électrique en cas de

fatigue ou sous l’influence de drogues, d’alcool ou

de médicaments. Un simple moment d’inattention en

utilisant un outil électrique peut entraîner des blessures

corporellesgraves.

b ) Utiliser des équipements de protection

individuelle. Toujours porter une protection

oculaire. L’utilisation d’équipements de protection

comme un masque antipoussière, des chaussures

AVERTISSEMENTS GÉNÉRAUX SUR LA

SÉCURITÉ DES OUTILS



AVERTISSEMENT : lisez tous les avertissements de

sécurité, toutes les instructions, les illustrations

et les caractéristiques fournis avec cet outil

électrique. Ne pas suivre toutes les instructions

comprises aux présentes peut conduire à un choc

électrique, un incendie et/ou des blessuresgraves.

CONSERVER TOUS LES

AVERTISSEMENTS ET TOUTES

LES DIRECTIVES POUR UN

USAGEULTÉRIEUR

Le terme « outil électrique » cité dans les avertissements se

rapporte à votre outil électrique à alimentation sur secteur

(avec fil) ou par piles (sansfil).

Définitions: symboles et termes

d'alarmessécurité

Ces guides d'utilisation utilisent les symboles et termes

d'alarmes sécurité suivants pour vous prévenir de situations

dangereuses et de risques de dommages corporels

oumatériels.



DANGER : indique une situation dangereuse

imminente qui, si elle n’est pas évitée, entraînera la

mort ou des blessuresgraves.



AVERTISSEMENT : indique une situation

potentiellement dangereuse qui, si elle n’est pas évitée,

pourrait entraîner la mort ou des blessuresgraves.



ATTENTION : indique une situation potentiellement

dangereuse qui, si elle n’est pas évitée, pourrait

entraîner des blessures légères oumodérées.



(Si utilisé sans aucun terme) Indique un message

propre à lasécurité.

AVIS : indique une pratique ne posant aucun risque

de dommages corporels mais qui par contre, si rien

n’est fait pour l’éviter, pourrait poser des risques de

dommagesmatériels.

Usage Prévu

Cette scie circulaire pour service dur est conçue pour les

applications de coupe du bois professionnelles. Ne pas

couper du métal, du plastique, du béton, de la maçonnerie

ou des matériaux à fibre deciment.

NE PAS les utiliser en milieu humide ou en présence de gaz

ou de liquidesinflammables.

NE PAS les laisser à la portée des enfants. Une supervision

est nécessaire auprès de tout utilisateur nonexpérimenté.

Français (traduction de la notice d’instructions originale)



AVERTISSEMENT : lire tous les avertissements

de sécurité et toutes les directives. Le non‑respect

des avertissements et des directives pourrait se

solder par un choc électrique, un incendie et/ou une

blessuregrave.

AVERTISSEMENT : afin de réduire le risque de

blessures, lire le mode d’emploi del’outil.

FRANÇAIS

e ) Gardez les poignées et surfaces d’emprise propres

et libres de tout produit lubrifiant. Vérifier si les

pièces mobiles sont mal alignées ou coincées,

si des pièces sont brisées ou présentent toute

autre condition susceptible de nuire au bon

fonctionnement de l’outil électrique. En cas de

dommage, faire réparer l’outil électrique avant

toute nouvelle utilisation. Beaucoup d’accidents

sont causés par des outils électriques malentretenus.

f ) S’assurer que les outils de coupe sont aiguisés et

propres. Les outils de coupe bien entretenus et affûtés

sont moins susceptibles de se coincer et sont plus faciles

àmaîtriser.

g ) Utiliser l’outil électrique, les accessoires, les forets,

etc. conformément aux présentes directives en

tenant compte des conditions de travail et du

travail à effectuer. L’utilisation d’un outil électrique

pour toute opération autre que celle pour laquelle il a

été conçu estdangereuse.

h ) Garder vos mains et les surfaces de prise sèches,

propres et libres de graisse et de poussière. Les

mains et les surfaces de prise glissante ne permettent

pas la manutention et le contrôle sécuritaires de l’outil

dans les situationsimprévues.

5) Utilisation et entretien du bloc-piles

a ) Ne recharger l’outil qu’au moyen du chargeur

précisé par le fabricant. L’utilisation d’un chargeur

qui convient à un type de bloc‑piles risque de

provoquer un incendie s’il est utilisé avec un autre type

de b loc‑piles.

b ) Utiliser les outils électriques uniquement avec

les blocs‑piles conçus à cet effet. L’utilisation de

tout autre bloc‑piles risque de causer des blessures ou

unincendie.

c ) Lorsque le bloc‑piles n’est pas utilisé, le tenir

éloigné des objets métalliques, notamment

des trombones, de la monnaie, des clés, des

clous, des vis ou autres petits objets métalliques

qui peuvent établir une connexion entre les

deux bornes. Le court‑circuit des bornes du bloc‑piles

risque de provoquer des brûlures ou unincendie.

d ) En cas d’utilisation abusive, le liquide peut gicler

hors du bloc‑piles; éviter tout contact avec ce

liquide. Si un contact accidentel se produit, laver

à grande eau. Si le liquide entre en contact avec

les yeux, obtenir également des soins médicaux.

Le liquide qui gicle hors du bloc‑piles peut provoquer

des irritations ou desbrûlures.

e ) Ne pas utiliser de bloc‑piles ou outil qui a été

endommagé ou modifié. Les unités endommagées

ou modifiées peuvent avoir une réaction

imprévisible résultant en un incendie, une

explosion ou un potentiel de blessure.

f ) Ne pas exposer de bloc‑piles ou l’outil aux

flammes ou à des températures excessives.

L’exposition aux flammes ou à une température

au‑dessus de 129°C (265°F) pourrait causer

uneexplosion.

antidérapantes, un casque de sécurité ou des

protecteurs auditifs lorsque la situation le requiert

réduira les risques de blessurescorporelles.

c ) Empêcher les démarrages intempestifs. S’assurer

que l’interrupteur se trouve à la position d’arrêt

avant de relier l’outil à une source d’alimentation

et/ou d’insérer un bloc‑piles, de ramasser ou de

transporter l’outil. Transporter un outil électrique

alors que le doigt repose sur l’interrupteur ou brancher

un outil électrique dont l’interrupteur est à la position

de marche risque de provoquer unaccident.

d ) Retirer toute clé de réglage ou clé avant de

démarrer l’outil. Une clé ou une clé de réglage

attachée à une partie pivotante de l’outil électrique

peut provoquer des blessurescorporelles.

e ) Ne pas trop tendre les bras. Conserver son

équilibre en tout temps. Cela permet de mieux

maîtriser l’outil électrique dans les situationsimprévues.

f ) S’habiller de manière appropriée. Ne pas porter

de vêtements amples ni de bijoux. Garder les

cheveux, les vêtements et les gants à l’écart des

pièces mobiles. Les vêtements amples, les bijoux ou

les cheveux longs risquent de rester coincés dans les

piècesmobiles.

g ) Si des composants sont fournis pour le

raccordement de dispositifs de dépoussiérage

et de ramassage, s’assurer que ceux‑ci sont bien

raccordés et utilisés. L’utilisation d’un dispositif de

dépoussiérage peut réduire les dangers engendrés par

lespoussières.

h ) Ne pas laisser votre connaissance acquise suite

l’utilisation fréquente des outils vous permettre

de baisser la garde et ignorer les principes de

sécurité de l’outil. Un acte irréfléchi peut causer une

blessure grave en une fraction deseconde.

4) Utilisation et entretien d’un

outilélectrique

a ) Ne pas forcer un outil électrique. Utiliser l’outil

électrique approprié à l’application. L’outil

électrique approprié effectuera un meilleur travail,

de façon plus sûre et à la vitesse pour laquelle il a

étéconçu.

b ) Ne pas utiliser un outil électrique dont

l’interrupteur est défectueux. Tout outil électrique

dont l’interrupteur est défectueux est dangereux et doit

êtreréparé.

c ) Débranchez la fiche de la prise électrique et, si

amovible, retirez le bloc‑piles de l’outil avant

d’effectuer tout ajustement, changement et

entreposage de celui‑ci. Ces mesures préventives

réduisent les risques de démarrage accidentel de

l’outilélectrique.

d ) Ranger les outils électriques hors de la portée

des enfants et ne permettre à aucune personne

n’étant pas familière avec un outil électrique ou

son mode d’emploi d’utiliser cet outil. Les outils

électriques deviennent dangereux entre les mains

d’utilisateursinexpérimentés.

FRANÇAIS

Consignes de sécurité supplémentaires

pour toutes les scies

Causes et prévention du rebond par

l’utilisateur :

• Le rebond est une réaction soudaine d’une la lame de la

scie pincée, bloquée ou désalignée, causant une scie non

contrôlée qui se soulève et sort de la pièce de travail vers

l’utilisateur;

• Lorsque la lame est pincée ou bloquée serrée par la

fermeture du trait de scie, la lame bloque et la réaction du

moteur ramène rapidement l’outil vers l’utilisateur;

• Si la lame devient tordue ou désalignée dans la coupe, les

dents du bord arrière de la lame peuvent pénétrer dans la

surface supérieure du bois faisant sortir la lame du trait et

rebondir versl’utilisateur.

Le rebond est le résultat d’une mauvaise utilisation de la scie

et/ou de procédures, ou de conditions de fonctionnement

incorrectes, et il peut être évité en prenant les précautions

appropriées définies ci‑dessous :

a ) Maintenez solidement la scie avec les deux mains

et placez vos bras de façon à ce qu’ils résistent

aux forces des rebonds. Placez votre corps d’un

côté ou l’autre de la lame, mais non en ligne avec

la lame. Le rebond pourrait faire en sorte que la scie

saute vers l'arrière, mais les forces des rebonds peuvent

être contrôlées par l’utilisateur si des précautions

appropriées sontprises.

b ) Lorsque la lame se coince ou si vous cessez une

coupe pour quelque raison que ce soit, relâchez

la gâchette et tenez la scie de coupe sans bouger

dans le matériau jusqu’à ce que la scie s’arrête

complètement. Ne jamais tenter de retirer la scie

du travail ou tirer la scie vers l’arrière pendant

que la scie est en mouvement sinon un rebond

peut se produire. Examinez‑la et prenez des mesures

correctives pour éliminer la cause du coincement de

lalame.

c ) Lors du redémarrage de la scie avec la pièce de

travail, centrez la lame de la scie dans le trait et

assurez‑vous que les dents de la scie ne sont pas

engagées dans le matériau. Si la lame de scie se

coince, elle pourrait se soulever ou rebondir de la pièce

de travail lors du redémarrage de lascie.

d ) Soutenez les grands panneaux afin de réduire le

risque de pincements de la lame et de rebonds.

Les panneaux de grandes dimensions ont

tendance à s’affaisser sous leur propre poids. Des

supports doivent être placés sous le panneau sur les

deux côtés, près de la ligne de coupe et près du bord

dupanneau.

h ) Ne vous servez jamais de rondelles ou de boulons

de lames qui sont endommagés ou inappropriés.

Les rondelles et le boulon de lame ont été conçus

spécifiquement pour votre scie dans le but d'assurer

une performance optimale et un fonctionnement

sansdanger.

Consignes de sécurité propres à toutes

lesscies

Procédures de coupe

a ) DANGER : kéloigner les mains des zones et

organes de coupe. Maintenir la deuxième main

sur la poignée auxiliaire ou le boîtier du moteur.

Lorsque les deux mains maintiennent la scie, la lame ne

peut lescouper.

b ) N’essayez pas de tenir le dessous de l’ouvrage. Le

protège‑lame ne peut pas vous protéger de la lame en

dessous del'ouvrage.

c ) Ajustez la profondeur de coupe à l’épaisseur de

l’ouvrage. Moins d’une dent entière de lame devrait

être visible en dessous del’ouvrage.

d ) Ne tenez jamais dans vos mains ou sur vos

genoux un ouvrage qui est en cours de coupe.

Fixez votre ouvrage sur une plateforme stable. Il

est important de soutenir correctement l’ouvrage afin

de minimiser l’exposition du corps à la lame, le risque

de coincement de la lame ou la perte de contrôle

del’outil.

e ) Tenez l’outil électrique par ses surfaces de

préhension isolantes quand vous réalisez une

opération au cours de laquelle l’outil de coupe

pourrait entrer en contact avec des câbles

dissimulés. Le contact avec un fil sous tension mettra

également sous tension toutes les pièces métalliques

exposées et donnera un choc électrique à l’utilisateur

del’outil.

f ) Pendant les coupes de refente, utilisez toujours

un guide de refente ou un guide à bord droit. Ceci

augmente toujours l’exactitude de la coupe et diminue

la possibilité de coincement de lalame.

g ) Utilisez toujours des lames dont l’alésage central

est de la taille et de la forme appropriées (soit

en forme de diamant, soit en forme de rond). Les

lames qui ne correspondent pas aux pièces de montage

de la cie tourneront de façon excentrique, ce qui

causera une perte de contrôle del’outil.

g ) Suivre toutes les instructions de recharge et

ne rechargez pas le bloc‑piles ou l’outil à des

températures hors de la plage de température

indiquée dans les instructions. Une recharge

non conforme ou à une température hors des limites

spécifiées peut endommager les piles et augmenter le

risqued’incendie.

6) Réparation

a ) Faire réparer l’outil électrique par un réparateur

professionnel en n’utilisant que des pièces de

rechange identiques. Cela permettra de maintenir

une utilisation sécuritaire de l’outilélectriques.

b ) Ne jamais réparer des blocs‑piles endommagés.

La réparation de blocs‑piles doit seulement être

effectuée par le fabricant ou les fournisseurs de

serviceautorisé.

FRANÇAIS

L’étiquette sur votre outil peut comporter les symboles suivants.

Les symboles et les définitions sont les suivants:

BPM .................... battements par

minute

V ......................... volts

min ..................... minutes

ou DC .......... courant continu

…/min .............. par minute

facial ou antipoussière si l'opération de coupe est

poussiéreuse. PORTEZ TOUJOURS UN ÉQUIPEMENT DE

SÉCURITÉ CERTIFIÉ:

• Protection des yeuxANSI Z87.1 (CAN/CSA Z94.3),

• protection auditive ANSI S12.6 (S3.19),

• protection respiratoire NIOSH/OSHA/MSHA.



AVERTISSEMENT : certaines poussières créées par le

ponçage mécanique, le sciage, l’aiguisage, le perçage

et autres activités de construction contiennent des

produits chimiques reconnus dans l’État de la Californie

pour causer le cancer et des anomalies congénitales

ou autres effets nuisibles sur la reproduction. Certains

exemples de ces produits chimiques sont:

• le plomb provenant des peintures à base de plomb,

• la silice cristallisée provenant des briques, du ciment

et d’autres produits de la maçonnerie ainsi que

• l’arsenic et le chrome provenant du bois de

construction traitéchimiquement.

Le risque associé à de telles expositions varie selon

la fréquence à laquelle on effectue ces travaux. Pour

réduire toute exposition à ces produits: travailler dans

un endroit bien aéré, en utilisant du matériel de sécurité

homologué, tel un masque antipoussières spécialement

conçu pour filtrer les particulesmicroscopiques.

• Portez des vêtements protecteurs et lavez vos zones

exposées avec du savon et de l’eau. Permettre à la

poussière d’entrer dans votre bouche, vos yeux ou la

laisser sur la peau peut favoriser l’absorption des produits

chimiques dangereux. Dirigez les particules loin du visage

et ducorps.

• Utilisez le dépoussiéreur approprié pour enlever la

grande majorité de la statique et de la poussière en

suspension. Ne pas enlever la statique et la poussière en

suspension pourrait contaminer l’environnement de travail

ou représenter un risque accru pour la santé de l’utilisateur

et ceux qui sont àproximité.

• Utilisez des pinces ou d’autres façons pratiques de

sécuriser et maintenez la pièce de travail sur une

plateforme stable. Tenir le travail par une main ou

contre votre corps est instable et peut mener à une perte de

contrôle et uneblessure.

• Les évents couvrent souvent des pièces qui se

déplacent et doivent être évités. Des vêtements amples,

les bijoux ou les cheveux longs peuvent se coincer dans des

pièces quidéplacent.



ATTENTION: lorsque vous ne l’utilisez pas, placez

l’outil sur le côté sur une surface stable là où cela

n’entraînera pas un risque de trébuchement ou

de chute. Certains outils avec de gros blocs‑piles se

tiendront debout sur le bloc‑piles, mais ils peuvent

facilement êtrerenversés.

Renseignements de sécurité

supplémentaires



AVERTISSEMENT : ne jamais modifier l’outil électrique

ou toute pièce de celui‑ci. Cela pourrait entraîner des

dommages matériels ou des blessurescorporelles.



AVERTISSEMENT : portez TOUJOURS des lunettes

de sécurité. Les lunettes de tous les jours NE SONT PAS

des lunettes de sécurité. De plus, utilisez un masque

e ) Ne pas utiliser des lames émoussées ou

endommagées. Les lames non aiguisées ou mal

placées produisent un trait de scie étroit causant une

friction excessive, le coincement de la lame et lerebond.

f ) La profondeur de la lame et les leviers de

verrouillage de l’ajustement du biseau doivent

être serrés et sécurisés avant de faire la coupe. Si

l’ajustement de la lame change pendant la coupe, cela

peut causer un coincement et unrebond.

g ) Soyez très prudent lorsque vous effectuez une

«coupe en plongée» dans les murs actuels ou

d’autres zones cachées. La lame qui dépasse peut

couper des objets qui peuvent causer unrebond.

Consignes de sécurité sur les fonctions

du protecteur inférieur

a ) Vérifiez le protecteur inférieur pour une fermeture

appropriée avant chaque utilisation. Ne pas

utiliser la scie si le protecteur inférieur ne bouge

pas librement et se ferme instantanément. Ne

jamais fixer ou attacher le protecteur inférieur

en position ouverte. Si la scie est accidentellement

échappée, le protecteur inférieur peut être plié. Levez

le protecteur inférieur avec la poignée rétractable

et assurez‑vous qu’il se déplace librement et qu’il ne

touche pas la lame ou toute autre pièce, dans tous les

angles et toutes lesprofondeurs.

b ) Vérifiez le fonctionnement du ressort du

protecteur inférieur. Si le protecteur et le ressort

ne fonctionnent pas correctement, ils doivent

être réparés avant l’utilisation. Le protecteur

inférieur peut fonctionner mollement en raison de

pièces endommagées, de dépôts collants ou d’une

accumulation dedébris.

c ) Le protecteur inférieur doit être rétracté

manuellement seulement pour les coupes

spéciales comme les « coupes en plongée » ou

les «coupes combinées». Levez le protecteur

inférieur en rétractant la poignée et dès que la

lame pénètre le matériau, le protecteur inférieur

doit être relâché. Pour tous les autres sciages, le

protecteur inférieur doit fonctionnerautomatiquement.

d ) Observez toujours le protecteur inférieur couvre

la lame avant de déposer la scie sur banc ou sur

le plancher. Une lame glissante non protégée fera en

sorte que la scie retournera en arrière en coupant tout

ce qui se trouve dans sa trajectoire. Tenez compte du

temps que cela prend pour que la lame s’arrête après

que la gâchette estrelâchée.

La page charge ...

DeWalt DCS565P1 Manuel utilisateur

Marque: DeWalt

Modèle: DCS565P1

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DCS565P1 User manual
español: DeWalt DCS565P1 Manual de usuario

DeWalt DCS565P1 Manuel utilisateur

DeWalt DCS565P1 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents