Worx WX531L.9 WORKXSAW Nitro 20V Power Share Cordless Compact Le manuel du propriétaire

Marque: Worx

Modèle: WX531L.9 WORKXSAW Nitro 20V Power Share Cordless Compact

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Ce manuel convient également à

WX531L WX531L.X

20V Cordless Brushless Circular saw EN

Scie circulaire sans ﬁl 20V sans brosse F

Sierra circular sin escobillas inalámbrica de 20V ES

P03

P19

P31

20V Cordless Brushless Circular saw EN

PRODUCT SAFETY

WARNING: Some dust created by power

sanding, sawing, grinding, drilling

and other construction activities contains

chemicals known to the State of California

to cause cancer, birth defects or other

reproductive harm. Some examples of these

chemicals are:

• Lead from lead-based paints;

• Crystalline silica from bricks and cement

and other masonry products;

• Arsenic and chromium from chemically-

treated lumber.

Your risk from these exposures varies,

depending on how often you do this type

of work. To reduce your exposure to these

chemicals: work in a well ventilated area,

and work with approved safety equipment,

such as those dust masks that are specially

designed to ﬁlter out microscopic particles.

WARNING: This product can expose

you to chemicals including lead and

Di (2-ethylhexyl) phthalate (DEHP) which

are known to the State of California to

cause cancer and birth defects or other

reproductive harm. For more information go

to www.P65Warnings.ca.gov.

GENERAL POWER TOOL

SAFETY WARNINGS

WARNING: Read all safety warnings,

instructions, illustrations and

speciﬁcations provided with this power tool.

Failure to follow all instructions listed below may

result in electric shock, ﬁre and/or serious injury.

Save all warnings and instructions for future

reference.

The term “power tool” in the warnings refers

to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂammable liquids, gases or dust. Power

tools create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can

cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do

not use any adapter plugs with earthed

(grounded) power tools. Unmodiﬁed plugs

and matching outlets will reduce risk of electric

shock.

b) Avoid body contact with earthed or

grounded surfaces, such as pipes,

radiators, ranges and refrigerators. There

is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool

will increase the risk of electric shock.

d) Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk

of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for

outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp

location is unavoidable, use a residual

current device (RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use a power tool while

you are tired or under the inﬂuence of

drugs, alcohol or medication. A moment

of inattention while operating power tools may

result in serious personal injury.

b) Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, non-skid safety

shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal

injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to power source and/or

battery pack, picking up or carrying the

tool. Carrying power tools with your ﬁnger on

the switch or energising power tools that have

the switch on invites accidents.

d) Remove any adjusting key or wrench

before turning the power tool on. A wrench

or a key left attached to a rotating part of the

power tool may result in personal injury.

e) Do not overreach. Keep proper footing

and balance at all times. This enables

better control of the power tool in unexpected

situations.

f) Dress properly. Do not wear loose

clothing or jewellery. Keep your hair and

clothing away from moving parts. Loose

clothes, jewellery or long hair can be caught in

moving parts.

g) If devices are provided for the connection

of dust extraction and collection

facilities, ensure these are connected

and properly used. Use of dust collection can

reduce dust-related hazards.

h) Do not let familiarity gained from

20V Cordless Brushless Circular saw EN

frequent use of tools allow you to become

complacent and ignore tool safety

principles. A careless action can cause severe

injury within a fraction of a second.

4) Power tool use and care

a) Do not force the power tool. Use the

correct power tool for your application.

The correct power tool will do the job better

and safer at the rate for which it was designed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power tool

that cannot be controlled with the switch is

dangerous and must be repaired.

c) Disconnect the plug from the power

source and/or remove the battery pack,

if detachable, from the power tool before

making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools and accessories.

Check for misalignment or binding of

moving parts, breakage of parts and any

other condition that may affect the power

tool’s operation. If damaged, have the

power tool repaired before use. Many

accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

g) Use the power tool, accessories and

tool bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations different from those intended could

result in a hazardous situation.

h) Keep handles and grasping surfaces

dry, clean and free from oil and grease.

Slippery handles and grasping surfaces do not

allow for safe handling and control of the tool in

unexpected situations.

5) Battery tool use and care

a) Recharge only with the charger speciﬁed

by the manufacturer. A charger that is

suitable for one type of battery pack may create

a risk of ﬁre when used with another battery

pack.

b) Use power tools only with speciﬁcally

designated battery packs. Use of any other

battery packs may create a risk of injury and

ﬁre.

c) When battery pack is not in use, keep it

away from other metal objects, like paper

clips, coins, keys, nails, screws or other

small metal objects, that can make a

connection from one terminal to another.

Shorting the battery terminals together may

cause burns or a ﬁre.

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact.

If contact accidentally occurs, ﬂush with

water. If liquid contacts eyes, additionally

seek medical help. Liquid ejected from the

battery may cause irritation or burns.

e) Do not use a battery pack or tool that is

damaged or modiﬁed. Damaged or modiﬁed

batteries may exhibit unpredictable behaviour

resulting in ﬁre, explosion or risk of injury.

f) Do not expose a battery pack or tool to

ﬁre or excessive temperature. Exposure

to ﬁre or temperature above 130 °C may cause

explosion.

g) Follow all charging instructions and

do not charge the battery pack or tool

outside the temperature range speciﬁed

in the instructions. Charging improperly or

at temperatures outside the speciﬁed range

may damage the battery and increase the risk

of ﬁre.

6) Service

a) Have your power tool serviced by

a qualiﬁed repair person using only

identical replacement parts. This will

ensure that the safety of the power tool is

maintained.

b) Never service damaged battery packs.

Service of battery packs should only be

performed by the manufacturer or authorized

service providers.

SAFETY INSTRUCTIONS

FOR ALL SAWS

CUTTING PROCEDURES

a) DANGER: Keep hands away from

cutting area and the blade. If both

hands are holding the saw, they cannot be cut

by the blade.

b) Do not reach underneath the workpiece.

The guard cannot protect you from the blade

below the workpiece.

c) Adjust the cutting depth to the thickness

of the workpiece. Less than a full tooth of

the blade teeth should be visible below the

workpiece.

d) Never hold the workpiece in your hands

or across your leg while cutting. Secure

the workpiece to a stable platform. It

is important to support the work properly to

minimise body exposure, blade binding, or loss

of control.

e) Hold the power tool by insulated gripping

surfaces, when performing an operation

where the cutting tool may contact

20V Cordless Brushless Circular saw EN

hidden wiring. Contact with a “live” wire will

also make exposed metal parts of the power

tool “live” and could give the operator an

electric shock.

f) When ripping, always use a rip fence

or straight edge guide. This improves the

accuracy of cut and reduces the chance of blade

binding.

g) Always use blades with correct size and

shape (diamond versus round) of arbour

holes. Blades that do not match the mounting

hardware of the saw will run off-centre, causing

loss of control.

h) Never use damaged or incorrect blade

washers or bolt. The blade washers and

bolt were specially designed for your saw, for

optimum performance and safety of operation.

FURTHER SAFETY

INSTRUCTIONS FOR ALL

SAWS

Kickback causes and related warnings

- kickback is a sudden reaction to a pinched,

jammed or misaligned saw blade, causing an

uncontrolled saw to lift up and out of the workpiece

toward the operator;

- when the blade is pinched or jammed tightly by

the kerf closing down, the blade stalls and the

motor reaction drives the unit rapidly back toward

the operator;

- if the blade becomes twisted or misaligned in the

cut, the teeth at the back edge of the blade can dig

into the top surface of the wood causing the blade

to climb out of the kerf and jump back toward the

operator.

Kickback is the result of saw misuse and/or

incorrect operating procedures or conditions and

can be avoided by taking proper precautions as

given below.

a) Maintain a ﬁrm grip on the saw and

position your arms to resist kickback

forces. Position your body to either

side of the blade, but not in line with

the blade. Kickback could cause the saw to

jump backwards, but kickback forces can be

controlled by the operator, if proper precautions

are taken.

b) When blade is binding, or when

interrupting a cut for any reason, release

the trigger and hold the saw motionless

in the material until the blade comes to a

complete stop. Never attempt to remove

the saw from the work or pull the saw

backward while the blade is in motion or

kickback may occur. Investigate and take

corrective actions to eliminate the cause of

blade binding.

c) When restarting a saw in the workpiece,

centre the saw blade in the kerf so that

the saw teeth are not engaged into the

material. If a saw blade binds, it may walk up

or kickback from the workpiece as the saw is

restarted.

d) Support large panels to minimise the

risk of blade pinching and kickback.

Large panels tend to sag under their own

weight. Supports must be placed under the

panel on both sides, near the line of cut and

near the edge of the panel.

e) Do not use dull or damaged blades.

Unsharpened or improperly set blades

produce narrow kerf causing excessive

friction, blade binding and kickback.

f) Blade depth and bevel adjusting locking

levers must be tight and secure before

making the cut. If blade adjustment shifts

while cutting, it may cause binding and

kickback.

g) Use extra caution when sawing into

existing walls or other blind areas. The

protruding blade may cut objects that can

cause kickback.

SAFETY INSTRUCTIONS FOR

CIRCULAR SAW WITH INNER

PENDULUM GUARD

LOWER GUARD FUNCTION

a) Check the lower guard for proper closing

before each use. Do not operate the saw

if the lower guard does not move freely

and close instantly. Never clamp or tie

the lower guard into the open position.

If the saw is accidentally dropped, the

lower guard may be bent. Raise the lower

guard with the retracting handle and make sure

it moves freely and does not touch the blade or

any other part, in all angles and depths of cut.

b) Check the operation of the lower guard

spring. If the guard and the spring are not

operating properly, they must be serviced

before use. Lower guard may operate

sluggishly due to damaged parts, gummy

deposits, or a build-up of debris.

c) The lower guard may be retracted

manually only for special cuts such as

“plunge cuts” and “compound cuts.”

Raise the lower guard by retracting

handle and as soon as the blade enters

the material, the lower guard must be

released. For all other sawing, the lower guard

should operate automatically.

d) Always observe that the lower guard is

covering the blade before placing the saw

down on bench or ﬂoor. An unprotected,

coasting blade will cause the saw to walk

backwards, cutting whatever is in its

path. Be aware of the time it takes for the blade

to stop after switch is released.

20V Cordless Brushless Circular saw EN

ADDITIONAL SAFETY RULES

FOR YOUR CIRCULAR SAW

1. Only use saw blades recommended in the

speciﬁcation.

2. Do not use any abrasive wheels.

3. Use only blade diameter(s) in accordance with

the markings.

4. Identify the correct saw blade to be used for

the material to be cut.

5. Use only saw blades that are marked with a

speed equal or higher than the speed marked

on the tool.

CUT-OFF MACHINE SAFETY

WARNINGS

a) The guard provided with the tool must

be securely attached to the power tool

and positioned for maximum safety, so

the least amount of wheel is exposed

towards the operator. Position yourself

and bystanders away from the plane

of the rotating wheel. The guard helps to

protect operator from broken wheel fragments

and accidental contact with wheel.

b) Use only bonded reinforced or diamond

cut-off wheels for your power tool. Just

because an accessory can be attached to your

power tool, it does not assure safe operation.

c) The rated speed of the accessory must

be at least equal to the maximum speed

marked on the power tool. Accessories

running faster than their rated speed can break

and ﬂy apart.

d) Wheels must be used only for

recommended applications. For example:

do not grind with the side of cut-off

wheel. Abrasive cut-off wheels are intended

for peripheral grinding, side forces applied to

these wheels may cause them to shatter.

e) Always use undamaged wheel ﬂanges

that are of correct diameter for your

selected wheel. Proper wheel ﬂanges

support the wheel thus reducing the possibility

of wheel breakage.

f) Do not use worn down reinforced wheels

from larger power tools. Wheels intended

for a larger power tool are not suitable for the

higher speed of a smaller tool and may burst.

g) The outside diameter and the thickness

of your accessory must be within the

capacity rating of your power tool.

Incorrectly sized accessories cannot be

adequately guarded or controlled.

h) The arbour size of wheels and ﬂanges

must properly ﬁt the spindle of the power

tool. Wheels and ﬂanges with arbour holes

that do not match the mounting hardware of

the power tool will run out of balance, vibrate

excessively and may cause loss of control.

i) Do not use damaged wheels. Before

each use, inspect the wheels for chips

and cracks. If power tool or wheel is

dropped, inspect for damage or install an

undamaged wheel. After inspecting and

installing the wheel, position yourself

and bystanders away from the plane of

the rotating wheel and run the power

tool at maximum no load speed for one

minute. Damaged wheels will normally break

apart during this test time.

j) Wear personal protective equipment.

Depending on application, use face

shield, safety goggles or safety glasses.

As appropriate, wear dust mask, hearing

protectors, gloves and shop apron

capable of stopping small abrasive or

workpiece fragments. The eye protection

must be capable of stopping ﬂying debris

generated by various operations. The

dust mask or respirator must be capable

of ﬁltrating particles generated by your

operation. Prolonged exposure to high

intensity noise may cause hearing loss.

k) Keep bystanders a safe distance away

from work area. Anyone entering the

work area must wear personal protective

equipment. Fragments of workpiece or of a

broken wheel may ﬂy away and cause injury

beyond immediate area of operation.

l) Hold the power tool by insulated gripping

surfaces only, when performing an

operation where the cutting accessory

may contact hidden wiring. Cutting

accessory contacting a “live” wire may make

exposed metal parts of the power tool “live”

and could give the operator an electric shock.

m) Position the cord clear of the spinning

accessory. If you lose control, the cord may

be cut or snagged and your hand or arm may

be pulled into the spinning wheel.

n) Never lay the power tool down until the

accessory has come to a complete stop.

The spinning wheel may grab the surface and

pull the power tool out of your control.

o) Do not run the power tool while carrying

it at your side. Accidental contact with the

spinning accessory could snag your clothing,

pulling the accessory into your body.

p) Regularly clean the power tool’s air

vents. The motor’s fan will draw the dust

inside the housing and excessive accumulation

of powdered metal may cause electrical

hazards.

q) Do not operate the power tool near

ﬂammable materials. Sparks could ignite

these materials.

r) Do not use accessories that require liquid

coolants. Using water or other liquid coolants

may result in electrocution or shock.

20V Cordless Brushless Circular saw EN

FURTHER SAFETY

INSTRUCTIONS FOR

ABRASIVE CUTTING-OFF

OPERATIONS

Kickback and related warnings

Kickback is a sudden reaction to a pinched or

snagged rotating wheel. Pinching or snagging

causes rapid stalling of the rotating wheel which in

turn causes the uncontrolled power tool to be forced

in the direction opposite of the wheel’s rotation at

the point of the binding.

For example, if an abrasive wheel is snagged or

pinched by the workpiece, the edge of the wheel

that is entering into the pinch point can dig into the

surface of the material causing the wheel to climb

out or kick out. The wheel may either jump toward

or away from the operator, depending on direction

of the wheel’s movement at the point of pinching.

Abrasive wheels may also break under these

conditions.

Kickback is the result of power tool misuse and/or

incorrect operating procedures or conditions and

can be avoided by taking proper precautions as

given below.

a) Maintain a ﬁrm grip on the power tool

and position your body and arm to allow

you to resist kickback forces. Always

use auxiliary handle, if provided, for

maximum control over kickback or torque

reaction during start-up. The operator can

control torque reactions or kickback forces, if

proper precautions are taken.

b) Never place your hand near the rotating

accessory. Accessory may kickback over your

hand.

c) Do not position your body in line with the

rotating wheel. Kickback will propel the

tool in direction opposite to the wheel’s

movement at the point of snagging.

d) Use special care when working corners,

sharp edges etc. Avoid bouncing and

snagging the accessory. Corners, sharp

edges or bouncing have a tendency to snag the

rotating accessory and cause loss of control or

kickback.

e) Do not attach a saw chain, woodcarving

blade, segmented diamond wheel with

a peripheral gap greater than 10 mm or

toothed saw blade. Such blades create

frequent kickback and loss of control.

f) Do not “jam” the wheel or apply

excessive pressure. Do not attempt

to make an excessive depth of cut.

Overstressing the wheel increases the loading

and susceptibility to twisting or binding of the

wheel in the cut and the possibility of kickback

or wheel breakage.

g) When wheel is binding or when

interrupting a cut for any reason, switch

off the power tool and hold the power

tool motionless until the wheel comes

to a complete stop. Never attempt to

remove the wheel from the cut while the

wheel is in motion otherwise kickback

may occur. Investigate and take corrective

action to eliminate the cause of wheel binding.

h) Do not restart the cutting operation in

the workpiece. Let the wheel reach full

speed and carefully re-enter the cut. The

wheel may bind, walk up or kickback if the

power tool is restarted in the workpiece.

i) Support panels or any oversized

workpiece to minimize the risk of wheel

pinching and kickback. Large workpieces

tend to sag under their own weight.

Supports must be placed under the workpiece

near the line of cut and near the edge of the

workpiece on both sides of the wheel.

j) Use extra caution when making a “pocket

cut” into existing walls or other blind

areas. The protruding wheel may cut gas or

water pipes, electrical wiring or objects that

can cause kickback.

ADDITIONAL SAFETY RULES:

1. Always wear a dust mask.

SAFETY WARNINGS FOR

BATTERY PACK

a) Do not dismantle, open or shred battery

pack.

b) Do not expose battery pack to heat or

ﬁre. Avoid storage in direct sunlight.

c) Do not short-circuit a battery pack. Do

not store battery packs haphazardly in

a box or drawer where they may short-

circuit each other or be short-circuited

by other metal objects. When battery pack

is not in use, keep it away from other metal

objects, like paper clips, coins, keys, nails,

screws or other small metal objects, that

can make a connection from one terminal

to another. Shorting the battery terminals

together may cause burns or ﬁre.

d) Do not remove battery pack from its

original packaging until required for use.

e) Do not subject battery pack to

mechanical shock.

f) In the event of battery leaking, do not

allow the liquid to come in contact with

the skin or eyes. If contact has been

made, wash the affected area with

copious amounts of water and seek

medical advice.

g) Observe the plus (+) and minus (–) marks

on the battery back and equipment and

ensure correct use.

h) Do not use any battery pack which is not

20V Cordless Brushless Circular saw EN

designed for use with the equipment.

i) Keep battery pack out of the reach of

children.

j) Seek medical advice immediately if a cell

or battery has been swallowed.

k) Always purchase the battery

pack recommended by the device

manufacturer for the equipment.

l) Keep battery pack clean and dry.

m) Wipe the battery pack terminals with a

clean dry cloth if they become dirty.

n) Battery pack needs to be charged before

use. Always use the correct charger and

refer to the manufacturer’s instructions

or equipment manual for proper charging

instructions.

o) Do not leave battery pack on prolonged

charge when not in use.

p) After extended periods of storage, it may

be necessary to charge and discharge

the battery pack several times to obtain

maximum performance.

q) Battery pack gives its best performance

when it is operated at normal room

temperature (68°F ± 9°F).

r) When disposing of battery packs,

keep battery packs of different

electrochemical systems separate from

each other.

s) Recharge only with the charger speciﬁed

by WorxNITRO. Do not use any charger

other than that speciﬁcally provided for

use with the equipment. A charger that is

suitable for one type of battery pack may create

a risk of ﬁre when used with another battery

pack.

t) Retain the original product literature for

future reference.

u) Use only the battery pack in the

application for which it was intended.

v) Remove the battery pack from the

equipment when not in use.

w) Dispose of properly.

SYMBOLS

To reduce the risk of injury, user must

read instruction manual

Warning

Wear ear protection

Wear eye protection

Wear dust mask

Batteries may enter water cycle if

disposed improperly, which can be

hazardous for ecosystem. Do not dispose

of waste batteries as unsorted municipal

waste.

Do not burn

Li-I on

Li-Ion battery, battery must be recycled

Make sure the battery is removed prior

to changing accessories

Wear protective gloves

Wood

Metal

Aluminium

Plastic

Tile

Incorrect

20V Cordless Brushless Circular saw EN

Correct

Lock

Unlock

Abrasive cutting disc

HCS blade

TCT blade

POSITEC Inc. has established a partnership with

the RBRC Corporation to recycle any Positec

batteries with the RBRC-call2recycle seal. For

environmental protection, please do not discard

batteries in the trash. After the batteries’ life

cycle is ended, then please call 1-800-822-8837

for a free service that will properly dispose of the

battery.

20V Cordless Brushless Circular saw EN

1 2 3

2021

20V Cordless Brushless Circular saw EN

COMPONENT LIST

1. SAFETY SWITCH

2. ON/OFF TRIGGER

3. SOFT GRIP HANDLE

4. HEX KEY

5. BLADE GUARD LEVER

6. BLADE GUARD

7. BASE PLATE

8. PARALLEL GUIDE

9. CUTTING MARK, 0°

10. CUTTING MARK, 45°

11. PARALLEL GUIDE CLAMPING FIXTURE

12. BEVEL ADJUSTMENT LEVER

13. DUST EXTRACTION OUTLET

14. VACUUM ADAPTER

15. FIXED UPPER BLADE GUARD

16. SPINDLE LOCK BUTTON

17. DEPTH ADJUSTMENT LEVER

18. BLADE BOLT

19. OUTER FLANGE

20. SAW BLADE*

21. INNER FLANGE

22. BATTERY PACK

* Not all the accessories illustrated or

described are included in standard delivery.

TECHNICAL DATA

Type WX531L WX531L.X (5- designation of

machinery, representative of Saw )

WX531L

WX531L.X**

Voltage 20V Max***

Rated speed 6900/min

No load speed 6900/min

Blade size

24T TCT

Blade(WA5043)

4-1/2 inch x 3/8

inch x 24T

4-1/2 inch

60T HCS

Blade(WA8302)

4-1/2 inch x 3/8

inch x 60T

4-1/2 inch

Abrasive

cutting blade

(WA5048)

4-1/2 inch x 3/8

inchx 60G

Cutting capacity

Cutting Depth

at 90°

1-1/2 inch

Cutting Depth

at 45°

1-1/8 inch

Bevel capacity 0-46°

Machine weight (Bare tool) 3.8 lbs

** X may be followed by one or two characters. All

models are the same except model number and

trademark.The sufﬁx in models may be number from

“1” to “999” or English letter “A” to “Z” or “M1” to”

M9” which means different package or the various of

accessories packed in the package.

***Voltage measured without workload. Initial

battery voltage reaches maximum of 20 volts.

Nominal voltage is 18 volts

Category

Type

Capacity

20V Battery

WA3578 4.0Ah

WA3012 4.0Ah

WA3525 2.0Ah

WA3520 1.5Ah

WA3575 2.0Ah

20V Charger

WA3881 2.0A

WA3742 0.4A

WA3875 2.0A

We recommend that you purchase your

accessories from the same store that sold you the

tool. Refer to the accessory packaging for further

details. Store personnel can assist you and offer

advice.

20V Cordless Brushless Circular saw EN

D1C

E1D2

A2A1

E2 F1

20V Cordless Brushless Circular saw EN

D1C

E1D2

A2A1

E2 F1

20V Cordless Brushless Circular saw EN

1.5

0.5

inch

1 3

1.5

0.5

inch

1.5

0.5

inch

20V Cordless Brushless Circular saw EN

1.5

0.5

inch

1 3

1.5

0.5

inch

1.5

0.5

inch

20V Cordless Brushless Circular saw EN

1.5

0.5

inch

1 3

1.5

0.5

inch

1.5

0.5

inch

20V Cordless Brushless Circular saw EN

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the

instruction book carefully.

ASSEMBLY AND OPERATION

ACTION FIGURE

BEFORE OPERATION

Removing the battery pack See Fig. A1

Charging the battery See Fig. A2

Installing the battery pack See Fig. A3

Mounting and Removing the

Blade

NOTE: Lock or loose the blade

bolt, the spindle lock button

should be pressed.

WARNING: Always

remove the battery

before changing the blade!

See Fig. B

Safety switch and On/Off

trigger

WARNING: To avoid

cutting injury from the

sharp blade, please don’t put

your hands around the Base

Plate.

NOTE: Keep the dust

adapter connected to dust

collecting device when using

the tool.

See Fig. C

Rip and Cross Cutting

NOTE: The cutting line of

saw blade is aligned with the

cutting mark 0°.

See Fig. D1, D2

Parallel Guide See Fig. E1, E2

Adjusting the Cutting Depth See Fig. F1, F2

Adjusting the Cutting Angle

NOTE: The cutting line of

saw blade is aligned with the

cutting mark 45°.

See Fig. G

Pocket /Plunge See Fig. H1, H2

Sawdust Removal See Fig. I

WORKING HINTS FOR YOUR

TOOL

Your power tool shall not be used for cutting

plastics. The blade may become very hot after

prolonged usage, please do not touch it.

MAINTAIN TOOLS WITH

CARE

Remove the battery before carrying out any

adjustment, servicing or maintenance.

Keep tools sharp and clean for better and safer

performance. Follow instructions for lubricating and

changing accessories. Inspect tool cords periodically

and if damaged, have repaired by authorized service

facility. Your power tool requires no additional

lubrication or maintenance. There are no user

serviceable parts in your power tool. Never use water

or chemical cleaners to clean your power tool. Wipe

clean with a dry cloth. Always store your power tool

in a dry place. Keep the motor ventilation slots clean.

Keep all working controls free of dust.

Periodically clear dust and chips from guard and

base to ensure proper performance.

FOR BATTERY TOOLS

The ambient temperature range for the use and

storage of tool and battery is 0

C-45

The recommended ambient temperature range for

the charging system during charging is 0

C-40

1918

20V Cordless Brushless Circular saw EN

TROUBLE SHOOTING

Symptom Possible Causes Possible Solution

Tool will not start when operating

the on/off trigger.

Battery park not plugged in.

Battery park is powered off.

Carbon brush has worn down

Check to make sure battery park is

connected well into a working outlet.

Charging the battery.

Replace the carbon brush using a

qualiﬁed maintenance person.

Cutting depth is less than that

is set.

Sawdust accumulated at the

rear of the base.

Shake out sawdust. Consider

connecting a vacuum for dust

collection.

Blade spins or slips Blade is not tightly engaged

with the spindle.

Remove the blade and reassemble

it as described in Mounting and

Removing the Blade section.

Blade will not cut a straight line. Blade is dull.

Blade is not mounted properly.

Saw is not being guided

properly.

Mount a new, sharp blade on the saw.

Check that blade is properly mounted.

Use a parallel guide.

Blade kicks back when beginning

a cut

Saw blade teeth may be

engaged in the material when

starting.

Blade is not spinning fast

enough

Before restarting a saw in the

workpiece, center the saw blade in the

kerf and check that the saw teeth are

not engaged into the material.

Allow the saw blade to reach full speed

prior to beginning a cut in the material.

1918

Scie circulaire sans fil 20V sans

brosse

SÉCURITÉ DU PRODUIT

AVERTISSEMENT! Certaines des

poussières produites en utilisant des

outils électriques sont considérées par

l’État de Californie comme susceptibles

de provoquer le cancer, des anomalies

congénitales et d’autres problèmes de

reproduction. Voici des exemples de ces

produits chimiques:

• plomb issu de peinture à base de plomb;

• silice crystalline issue de briques et du

ciment et autres produits de maçonnerie;

• arsenic et chrome issus de bois traité

chimiquement.

Votre risque de ces expositions varie en

fonction de la fréquence à laquelle vous

effectuez ce travail. Pour réduire votre

exposition à ces produits chimiques :

travaillez dans une zone bien ventilée; portez

un équipement de sécurité approuvé, tel que

des masques antipoussières spécialement

conçus pour éliminer les particules

microscopiques par ﬁltrage.

AVERTISSEMENT : Ce dispositif peut

vous exposer aux produits chimiques

notamment le plomb et le di-phtalate (de

2-éthylhexyle) (DEHP) qui sont reconnus

dans l’État de Californie comme causant

des cancers et des anomalies congénitales

ou d’autres anomalies de la reproduction.

Pour en savoir plus, veuillez consulter le site

www.P65Warnings.ca.gov.

AVERTISSEMENTS

GENERAUX CONCERNANT

LA SECURITE DES OUTILS

ELECTRIQUES

AVERTISSEMENT Lisez et assimilez

toutes les instructions. Le non-respect des

instructions ci-après peut entraîner un risque de choc

électrique, d’incendie et/ou de blessures graves.

Conservez tous les avertissements et

instructions pour pouvoir les consulter

ultérieurement.

L’expression « outil électrique » dans tous les

avertissements énumérés ci-dessous se réfère

à votre outil électrique fonctionnant sur secteur

(branché) ou à batterie (sans-ﬁl).

1) Aire de travail

a) Veillez à ce que l’aire de travail soit

propre et bien éclairée. Le désordre et le

manque de lumière favorisent les accidents.

b) N’utilisez pas d’outils électriques dans un

milieu présentant un risque d’explosion,

par exemple en présence de liquides,

de gaz ou de poussières inﬂammables.

Les outils électriques créent des étincelles qui

pourraient enﬂammer les poussières ou les

vapeurs.

c) Gardez à distance les curieux, les enfants

et les visiteurs lorsque vous travaillez

avec un outil électrique. Ils pourraient

vous distraire et vous faire faire une fausse

manoeuvre.

2) Sécurité électrique

a) Les ﬁches des outils électriques doivent

correspondre aux prises murales. Ne

jamais modiﬁer la ﬁche de quelque façon

que ce soit. Ne pas utiliser de ﬁches

d’adaptation avec des outils électriques

mis à la terre (mis à la masse). Des

ﬁches non modiﬁées et des prises qui leur

correspondent réduiront le risque de choc

électrique.

b) Évitez tout contact corporel avec des

surfaces mises à la terre (tuyauterie,

radiateurs, cuisinières, réfrigérateurs,

etc. Le risque de choc électrique est plus grand

si votre corps est en contact avec la terre.

c) N’exposez pas les outils électriques à la

pluie ou à l’eau. La présence d’eau dans un

outil électrique augmente le risque de choc

électrique.

d) Ne maltraitez pas le cordon. Ne

transportez jamais l’outil par son cordon

et ne débranchez jamais la ﬁche en tirant

sur le cordon. N’exposez pas le cordon à

la chaleur, à des huiles, à des arrêtes vives

ou à des pièces en mouvement. Un cordon

endommagé augmente le risque de choc

électrique.

e) Lorsque vous utilisez un outil électrique

à l’extérieur, utilisez un prolongateur

adapté à une utilisation en extérieur.

L’utilisation d’un cordon adapté à une utilisation

extérieure réduit le risque de choc électrique.

f) Si vous devez utiliser un outil électrique

dans un endroit humide, utilisez un

dispositif de courant résiduel (RCD)

d’alimentation protégée. L’utilisation d’un

RCD réduit le risque de choc électrique.

3) Sécurité des personnes

a) Restez alerte, concentrez-vous sur

votre travail et faites preuve de bon

sens. N’utilisez pas un outil électrique si

vous êtes fatigué ou sous l’inﬂuence de

drogues, d’alcool ou de médicaments. Un

instant d’inattention lors de l’utilisation d’outils

électriques peut entraîner des blessures graves.

b) Utilisez des accessoires de sécurité.

Portez toujours une protection oculaire.

De l’équipement de sécurité tel que le

masque antipoussière, les chaussures de

sécurité antidérapantes, des casques durs

ou des protections antibruit utilisés dans des

conditions appropriées réduiront les blessures

corporelles.

c) Évitez les démarrages accidentels.

Avant d’insérer la batterie dans l’outil,

2120

Scie circulaire sans fil 20V sans

brosse

assurez-vous que son interrupteur est en

position « OFF » (Arrêt) ou verrouillée. Le

fait de transporter un outil avec le doigt sur la

détente/l’interrupteur ou d’insérer la batterie

dans un outil dont la détente est en position «

ON » (Marche) peut causer un accident.

d) Retirer les clés de réglage avant de

mettre l’outil sous tension. Une clé restée

attachée à une partie mobile de l’outil pourrait

entraîner des blessures corporelles.

e) Ne vous penchez pas trop en avant.

Maintenez un bon appui et restez en

équilibre en tout temps. Une bonne stabilité

vous permet de mieux réagir à une situation

inattendue.

f) Habillez-vous convenablement. Ne portez

ni vêtements ﬂottants ni bijoux. Gardez

les cheveux, les vêtements et les gants

éloignés des pièces en mouvement. Les

vêtements ﬂottants, les bijoux ou les cheveux

longs risquent d’être happés par des pièces en

mouvement.

g) Si un sac de récupération de la poussière

est fourni avec un connecteur pour

aspirateur, assurez vous qu’il est

correctement relié et utilisé de façon

appropriée. L’utilisation de ce système réduit

les dangers physiques et physiologiques liés à

la poussière.

h) Ne laissez pas les habitudes acquises par

une utilisation fréquente d’outils relâcher

notre vigilance et ignorer les principes

de sécurité des outils. Une utilisation

négligente peut causer des blessures graves en

une fraction de seconde.

4) Utilisation et entretien de l’outil

a) Ne forcez pas l’outil. Utilisez l’outil

approprié à la tâche. L’outil approprié

fonctionne mieux et de façon plus

sécuritaire. Respectez aussi la vitesse de

travail qui lui est propre.

b) N’utilisez pas un outil si l’interrupteur

ne le met pas en marche ou ne peut

l’arrêter. Un outil qui ne peut être contrôlé par

l’interrupteur est dangereux et doit être réparé.

c) Débranchez la batterie de l’outil ou

mettez son interrupteur en position «

OFF » (Arrêt) ou « LOCKED » (Verrouillé)

avant d’effectuer un réglage, de changer

d’accessoire ou de ranger l’outil. De telles

mesures de sécurité préventive réduisent le

risque de démarrage accidentel de l’outil.

d) Rangez les outils hors de portée

des enfants et d’autres personnes

inexpérimentées. Les outils sont dangereux

dans les mains d’utilisateurs novices.

e) Prenez soin de bien entretenir les outils.

Soyez attentif à tout désalignement ou

coincement des pièces en mouvement,

à tout bris ou à toute autre condition

préjudiciable au bon fonctionnement de

l’outil. Si vous constatez qu’un outil est

endommagé, faites-le réparer avant de

vous en servir. De nombreux accidents sont

causés par des outils en mauvais état.

f) Les outils de coupe doivent être toujours

bien affûtés et propres. Des outils

bien entretenus, dont les arêtes sont bien

tranchantes, sont moins susceptibles de se

coincer et plus faciles à contrôler.

g) Utilisez l’outil électrique, les accessoires

et les forets etc., en conformité avec

ces instructions et de la manière conçue

pour le type particulier d’outil électrique,

prend en compte les conditions de

travail et le travail qui doit être accompli.

L’emploi de l’outil électrique pour des

opérations différentes de celles pour lesquelles

il a été conçu pourrait entraîner une situation

dangereuse.

h) Maintenez les poignées et les surfaces de

prise sèches, propres et exemptes d’huile

et de graisse. Des poignées et surfaces

de prise glissantes ne permettent pas une

manipulation et un contrôle sécurisés de l’outil

dans des situations inattendues.

5) Utilisation de la batterie et entretien

a) Un outil à batterie avec batteries

incorporées ou une batterie séparée

doit être rechargé uniquement avec le

chargeur indiqué pour la batterie. Un

chargeur qui peut être adéquat pour un type de

batterie peut créer un risque d’incendie lorsqu’il

est utilisé avec une autre batterie.

b) Utiliser un outil à batterie uniquement

avec la batterie désignée. L’emploi de toute

autre batterie peut créer un risque d’incendie.

c) Lorsque la batterie n’est pas utilisée,

tenez-la à l’écart d’autres objets

métalliques tels que trombones, pièces

de monnaie, clés, clous, vis ou autres

petits objets métalliques susceptibles

d’établir une connexion d’une borne à

une autre. Le court-circuitage des bornes

de batterie peut causer des étincelles, des

brûlures, une explosion ou un incendie.

d) Dans le cadre de conditions d’abus, du

ﬂuide peut être éjecté de la batterie,

évitez tout contact. Si un contact se

produisait accidentellement, rincez

abondamment avec de l’eau. Si le ﬂuide

touche les yeux, cherchez en plus de la

mesure précédente de l’aide médicale.

Le ﬂuide éjecté de la batterie peut causer des

irritations ou des brûlures.

e) N’utilisez pas une batterie ou un outil

endommagé ou modiﬁé. Les batteries

endommagées ou modiﬁées peuvent avoir

un comportement imprévisible entraînant

un incendie, une explosion ou un risque de

blessure.

f) N’exposez pas une batterie ou un outil

au feu ou à une température excessive.

Une exposition au feu ou à une température

supérieure à 265 °F pourrait provoquer une

explosion.

La page charge ...

Worx WX531L.9 WORKXSAW Nitro 20V Power Share Cordless Compact Le manuel du propriétaire

Marque: Worx

Modèle: WX531L.9 WORKXSAW Nitro 20V Power Share Cordless Compact

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

Worx WX531L.9 WORKXSAW Nitro 20V Power Share Cordless Compact Le manuel du propriétaire

Ce manuel convient également à

Worx WX531L.9 WORKXSAW Nitro 20V Power Share Cordless Compact Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents